netlink_dump() returns a negative errno value on error. Until now,
netlink_recvmsg() directly recorded that negative value in sk->sk_err, but
that's wrong since sk_err takes positive errno values. (This manifests as
userspace receiving a positive return value from the recv() system call,
falsely indicating success.) This bug was introduced in the commit that
started checking the netlink_dump() return value, commit b44d211 (netlink:
handle errors from netlink_dump()).
Multithreaded Netlink dumps are one way to trigger this behavior in
practice, as described in the commit message for the userspace workaround
posted here:
http://openvswitch.org/pipermail/dev/2014-June/042339.html
This commit also fixes the same bug in netlink_poll(), introduced in commit cd1df525d (netlink: add flow control for memory mapped I/O).
Signed-off-by: Ben Pfaff <blp@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204da0 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+ Fixes: c5aff18204da0 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com> Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting just skb->sk without taking its reference and setting a
destructor is invalid. However, in the places where this was done, skb
is used in a way not requiring skb->sk setting. So dropping the setting
of skb->sk.
Thanks to Eric Dumazet <eric.dumazet@gmail.com> for correct solution.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79441 Reported-by: Ed Martin <edman007@edman007.com> Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The undo code assumes that, upon entering loss recovery, TCP
1) always retransmit something
2) the retransmission never fails locally (e.g., qdisc drop)
so undo_marker is set in tcp_enter_recovery() and undo_retrans is
incremented only when tcp_retransmit_skb() is successful.
When the assumption is broken because TCP's cwnd is too small to
retransmit or the retransmit fails locally. The next (DUP)ACK
would incorrectly revert the cwnd and the congestion state in
tcp_try_undo_dsack() or tcp_may_undo(). Subsequent (DUP)ACKs
may enter the recovery state. The sender repeatedly enter and
(incorrectly) exit recovery states if the retransmits continue to
fail locally while receiving (DUP)ACKs.
The fix is to initialize undo_retrans to -1 and start counting on
the first retransmission. Always increment undo_retrans even if the
retransmissions fail locally because they couldn't cause DSACKs to
undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) create socket, bind and then setsockopt for add mc group.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("192.168.1.2");
setsockopt(sockfd, IPPROTO_IP, IP_ADD_MEMBERSHIP, &mreq, sizeof(mreq));
2) drop the mc group for this socket.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("0.0.0.0");
setsockopt(sockfd, IPPROTO_IP, IP_DROP_MEMBERSHIP, &mreq, sizeof(mreq));
3) and then drop the socket, I found the mc group was still used by the dev:
netstat -g
Interface RefCnt Group
--------------- ------ ---------------------
eth2 1 255.0.0.37
Normally even though the IP_DROP_MEMBERSHIP return error, the mc group still need
to be released for the netdev when drop the socket, but this process was broken when
route default is NULL, the reason is that:
The ip_mc_leave_group() will choose the in_dev by the imr_interface.s_addr, if input addr
is NULL, the default route dev will be chosen, then the ifindex is got from the dev,
then polling the inet->mc_list and return -ENODEV, but if the default route dev is NULL,
the in_dev and ifIndex is both NULL, when polling the inet->mc_list, the mc group will be
released from the mc_list, but the dev didn't dec the refcnt for this mc group, so
when dropping the socket, the mc_list is NULL and the dev still keep this group.
v1->v2: According Hideaki's suggestion, we should align with IPv6 (RFC3493) and BSDs,
so I add the checking for the in_dev before polling the mc_list, make sure when
we remove the mc group, dec the refcnt to the real dev which was using the mc address.
The problem would never happened again.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some older router implementations still send Fragmentation Needed
errors with the Next-Hop MTU field set to zero. This is explicitly
described as an eventuality that hosts must deal with by the
standard (RFC 1191) since older standards specified that those
bits must be zero.
Linux had a generic (for all of IPv4) implementation of the algorithm
described in the RFC for searching a list of MTU plateaus for a good
value. Commit 46517008e116 ("ipv4: Kill ip_rt_frag_needed().")
removed this as part of the changes to remove the routing cache.
Subsequently any Fragmentation Needed packet with a zero Next-Hop
MTU has been discarded without being passed to the per-protocol
handlers or notifying userspace for raw sockets.
When there is a router which does not implement RFC 1191 on an
MTU limited path then this results in stalled connections since
large packets are discarded and the local protocols are not
notified so they never attempt to lower the pMTU.
One example I have seen is an OpenBSD router terminating IPSec
tunnels. It's worth pointing out that this case is distinct from
the BSD 4.2 bug which incorrectly calculated the Next-Hop MTU
since the commit in question dismissed that as a valid concern.
All of the per-protocols handlers implement the simple approach from
RFC 1191 of immediately falling back to the minimum value. Although
this is sub-optimal it is vastly preferable to connections hanging
indefinitely.
Remove the Next-Hop MTU != 0 check and allow such packets
to follow the normal path.
Fixes: 46517008e116 ("ipv4: Kill ip_rt_frag_needed().") Signed-off-by: Edward Allcutt <edward.allcutt@openmarket.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in repair-mode and TCP_RECV_QUEUE is set, we end up calling
tcp_push with mss_now being 0. If data is in the send-queue and
tcp_set_skb_tso_segs gets called, we crash because it will divide by
mss_now:
This can easily be reproduced with the following packetdrill-script (the
"magic" with netem, sk_pacing and limit_output_bytes is done to prevent
the kernel from pushing all segments, because hitting the limit without
doing this is not so easy with packetdrill):
// This forces that not all segments of the snd-queue will be pushed
+0 `tc qdisc add dev tun0 root netem delay 10ms`
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=2`
+0 setsockopt(4, SOL_SOCKET, 47, [2], 4) = 0
// This now will make the write push the remaining segments
+0 setsockopt(4, SOL_SOCKET, 47, [20000], 4) = 0
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=130000`
// Now we will crash
+0 write(4,...,1000) = 1000
This happens since ec3423257508 (tcp: fix retransmission in repair
mode). Prior to that, the call to tcp_push was prevented by a check for
tp->repair.
The patch fixes it, by adding the new goto-label out_nopush. When exiting
tcp_sendmsg and a push is not required, which is the case for tp->repair,
we go to this label.
When repairing and calling send() with TCP_RECV_QUEUE, the data is
actually put in the receive-queue. So, no push is required because no
data has been added to the send-queue.
Cc: Andrew Vagin <avagin@openvz.org> Cc: Pavel Emelyanov <xemul@parallels.com> Fixes: ec3423257508 (tcp: fix retransmission in repair mode) Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Acked-by: Andrew Vagin <avagin@openvz.org> Acked-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Michel Lespinasse <walken@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ariel Elior <ariel.elior@qlogic.com> Fixes: d46d132cc021 ("bnx2x: use netdev_alloc_frag()") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sk_dst_cache has __rcu annotation, so we need a cast to avoid
following sparse error :
include/net/sock.h:1774:19: warning: incorrect type in initializer (different address spaces)
include/net/sock.h:1774:19: expected struct dst_entry [noderef] <asn:4>*__ret
include/net/sock.h:1774:19: got struct dst_entry *dst
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: 7f502361531e ("ipv4: irq safe sk_dst_[re]set() and ipv4_sk_update_pmtu() fix") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have two different ways to handle changes to sk->sk_dst
First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()
Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.
These ways are not inter changeable for a given socket type.
ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.
Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5dfb296b ("udp: ipv4: do not use
sk_dst_lock from softirq context")
In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Fixes: 9cb3a50c5f63e ("ipv4: Invalidate the socket cached route on pmtu events if possible") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.
In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.
DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.
Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dormando <dormando@rydia.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When writing to the sysctl field net.sctp.auth_enable, it can well
be that the user buffer we handed over to proc_dointvec() via
proc_sctp_do_auth() handler contains something other than integers.
In that case, we would set an uninitialized 4-byte value from the
stack to net->sctp.auth_enable that can be leaked back when reading
the sysctl variable, and it can unintentionally turn auth_enable
on/off based on the stack content since auth_enable is interpreted
as a boolean.
Fix it up by making sure proc_dointvec() returned sucessfully.
Fixes: b14878ccb7fa ("net: sctp: cache auth_enable per endpoint") Reported-by: Florian Westphal <fwestpha@redhat.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is an MSS change (or misbehaving receiver) that causes a SACK
to arrive that covers the end of an skb but is less than one MSS, then
tcp_match_skb_to_sack() was rounding up pkt_len to the full length of
the skb ("Round if necessary..."), then chopping all bytes off the skb
and creating a zero-byte skb in the write queue.
This was visible now because the recently simplified TLP logic in bef1909ee3ed1c ("tcp: fixing TLP's FIN recovery") could find that 0-byte
skb at the end of the write queue, and now that we do not check that
skb's length we could send it as a TLP probe.
Previously we would find the new_len > skb->len check failing, so we
would fall through and set pkt_len = new_len = 4000 and chop off
pkt_len of 4000 from the 4000-byte skb, leaving a 0-byte segment
afterward in the write queue.
With this new commit, we notice that the new new_len >= skb->len check
succeeds, so that we return without trying to fragment.
Fixes: adb92db857ee ("tcp: Make SACK code to split only at mss boundaries") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes 3 similar bugs where incoming packets might be routed into
wrong non-wildcard tunnels:
1) Consider the following setup:
ip address add 1.1.1.1/24 dev eth0
ip address add 1.1.1.2/24 dev eth0
ip tunnel add ipip1 remote 2.2.2.2 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets from 2.2.2.2 were routed into ipip1 even if it has dst =
1.1.1.2. Moreover even if there was wildcard tunnel like
ip tunnel add ipip0 remote 2.2.2.2 local any mode ipip dev eth0
but it was created before explicit one (with local 1.1.1.1), incoming ipip
packets with src = 2.2.2.2 and dst = 1.1.1.2 were still routed into ipip1.
Same issue existed with all tunnels that use ip_tunnel_lookup (gre, vti)
2) ip address add 1.1.1.1/24 dev eth0
ip tunnel add ipip1 remote 2.2.146.85 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets with dst = 1.1.1.1 were routed into ipip1, no matter what
src address is. Any remote ip address which has ip_tunnel_hash = 0 raised this
issue, 2.2.146.85 is just an example, there are more than 4 million of them.
And again, wildcard tunnel like
ip tunnel add ipip0 remote any local 1.1.1.1 mode ipip dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
Gre & vti tunnels had the same issue.
3) ip address add 1.1.1.1/24 dev eth0
ip tunnel add gre1 remote 2.2.146.84 local 1.1.1.1 key 1 mode gre dev eth0
ip link set gre1 up
Any incoming gre packet with key = 1 were routed into gre1, no matter what
src/dst addresses are. Any remote ip address which has ip_tunnel_hash = 0 raised
the issue, 2.2.146.84 is just an example, there are more than 4 million of them.
Wildcard tunnel like
ip tunnel add gre2 remote any local any key 1 mode gre dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
All this stuff happened because while looking for a wildcard tunnel we didn't
check that matched tunnel is a wildcard one. Fixed.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
shmem_fault() is the actual culprit in trinity's hole-punch starvation,
and the most significant cause of such problems: since a page faulted is
one that then appears page_mapped(), needing unmap_mapping_range() and
i_mmap_mutex to be unmapped again.
But it is not the only way in which a page can be brought into a hole in
the radix_tree while that hole is being punched; and Vlastimil's testing
implies that if enough other processors are busy filling in the hole,
then shmem_undo_range() can be kept from completing indefinitely.
shmem_file_splice_read() is the main other user of SGP_CACHE, which can
instantiate shmem pagecache pages in the read-only case (without holding
i_mutex, so perhaps concurrently with a hole-punch). Probably it's
silly not to use SGP_READ already (using the ZERO_PAGE for holes): which
ought to be safe, but might bring surprises - not a change to be rushed.
shmem_read_mapping_page_gfp() is an internal interface used by
drivers/gpu/drm GEM (and next by uprobes): it should be okay. And
shmem_file_read_iter() uses the SGP_DIRTY variant of SGP_CACHE, when
called internally by the kernel (perhaps for a stacking filesystem,
which might rely on holes to be reserved): it's unclear whether it could
be provoked to keep hole-punch busy or not.
We could apply the same umbrella as now used in shmem_fault() to
shmem_file_splice_read() and the others; but it looks ugly, and use over
a range raises questions - should it actually be per page? can these get
starved themselves?
The origin of this part of the problem is my v3.1 commit d0823576bf4b
("mm: pincer in truncate_inode_pages_range"), once it was duplicated
into shmem.c. It seemed like a nice idea at the time, to ensure
(barring RCU lookup fuzziness) that there's an instant when the entire
hole is empty; but the indefinitely repeated scans to ensure that make
it vulnerable.
Revert that "enhancement" to hole-punch from shmem_undo_range(), but
retain the unproblematic rescanning when it's truncating; add a couple
of comments there.
Remove the "indices[0] >= end" test: that is now handled satisfactorily
by the inner loop, and mem_cgroup_uncharge_start()/end() are too light
to be worth avoiding here.
But if we do not always loop indefinitely, we do need to handle the case
of swap swizzled back to page before shmem_free_swap() gets it: add a
retry for that case, as suggested by Konstantin Khlebnikov; and for the
case of page swizzled back to swap, as suggested by Johannes Weiner.
Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Sasha Levin <sasha.levin@oracle.com> Suggested-by: Vlastimil Babka <vbabka@suse.cz> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Lukas Czerner <lczerner@redhat.com> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f00cdc6df7d7 ("shmem: fix faulting into a hole while it's
punched") was buggy: Sasha sent a lockdep report to remind us that
grabbing i_mutex in the fault path is a no-no (write syscall may already
hold i_mutex while faulting user buffer).
We tried a completely different approach (see following patch) but that
proved inadequate: good enough for a rational workload, but not good
enough against trinity - which forks off so many mappings of the object
that contention on i_mmap_mutex while hole-puncher holds i_mutex builds
into serious starvation when concurrent faults force the puncher to fall
back to single-page unmap_mapping_range() searches of the i_mmap tree.
So return to the original umbrella approach, but keep away from i_mutex
this time. We really don't want to bloat every shmem inode with a new
mutex or completion, just to protect this unlikely case from trinity.
So extend the original with wait_queue_head on stack at the hole-punch
end, and wait_queue item on the stack at the fault end.
This involves further use of i_lock to guard against the races: lockdep
has been happy so far, and I see fs/inode.c:unlock_new_inode() holds
i_lock around wake_up_bit(), which is comparable to what we do here.
i_lock is more convenient, but we could switch to shmem's info->lock.
This issue has been tagged with CVE-2014-4171, which will require commit f00cdc6df7d7 and this and the following patch to be backported: we
suggest to 3.1+, though in fact the trinity forkbomb effect might go
back as far as 2.6.16, when madvise(,,MADV_REMOVE) came in - or might
not, since much has changed, with i_mmap_mutex a spinlock before 3.0.
Anyone running trinity on 3.0 and earlier? I don't think we need care.
Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Sasha Levin <sasha.levin@oracle.com> Tested-by: Sasha Levin <sasha.levin@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Lukas Czerner <lczerner@redhat.com> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trinity finds that mmap access to a hole while it's punched from shmem
can prevent the madvise(MADV_REMOVE) or fallocate(FALLOC_FL_PUNCH_HOLE)
from completing, until the reader chooses to stop; with the puncher's
hold on i_mutex locking out all other writers until it can complete.
It appears that the tmpfs fault path is too light in comparison with its
hole-punching path, lacking an i_data_sem to obstruct it; but we don't
want to slow down the common case.
Extend shmem_fallocate()'s existing range notification mechanism, so
shmem_fault() can refrain from faulting pages into the hole while it's
punched, waiting instead on i_mutex (when safe to sleep; or repeatedly
faulting when not).
We should always prefer to use full RTS protection. Using
CTS to self gives a meaningless improvement, but this flow
is much harder for the firmware which is likely to have
issues with it.
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently trace option stacktrace is not applicable for
trace_printk with constant string argument, the reason is
in __trace_puts/__trace_bputs ftrace_trace_stack is missing.
In contrast, when using trace_printk with non constant string
argument(will call into __trace_printk/__trace_bprintk), then
trace option stacktrace is workable, this inconstant result
will confuses users a lot.
Running my ftrace tests on PowerPC, it failed the test that checks
if function_graph tracer is affected by the stack tracer. It was.
Looking into this, I found that the update_function_graph_func()
must be called even if the trampoline function is not changed.
This is because archs like PowerPC do not support ftrace_ops being
passed by assembly and instead uses a helper function (what the
trampoline function points to). Since this function is not changed
even when multiple ftrace_ops are added to the code, the test that
falls out before calling update_function_graph_func() will miss that
the update must still be done.
Call update_function_graph_function() for all calls to
update_ftrace_function()
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Add code to poll the channel since we process only one message
at a time and the host may not interrupt us. Also increase the
receive buffer size since some KVP messages are close to 8K bytes in size.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cdc662f704fa9262e5c6e213b4ab45dd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cdc6 (USB: Allow USB 3.0 ports to be disabled.) Signed-off-by: Gavin Guo <gavin.guo@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some machines (eg. Lenovo Z480) ECs are not stable during boot up
and causes battery driver fails to be loaded due to failure of getting
battery information from EC sometimes. After several retries, the
operation will work. This patch is to retry to get battery information 5
times if the first try fails.
[ backport to 3.14.5: removed second parameter in acpi_battery_update(),
introduced by the commit 9e50bc14a7f58b5d8a55973b2d69355852ae2dae (ACPI /
battery: Accelerate battery resume callback)]
[naszar <naszar@ya.ru>: backport to 3.14.5] Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581 Reported-and-tested-by: naszar <naszar@ya.ru> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __ioremap_caller() (the guts of ioremap), we loop over the range of
pfns being remapped and checks each one individually with page_is_ram().
For large ioremaps, this can be very slow. For example, we have a
device with a 256 GiB PCI BAR, and ioremapping this BAR can take 20+
seconds -- sometimes long enough to trigger the soft lockup detector!
Internally, page_is_ram() calls walk_system_ram_range() on a single
page. Instead, we can make a single call to walk_system_ram_range()
from __ioremap_caller(), and do our further checks only for any RAM
pages that we find. For the common case of MMIO, this saves an enormous
amount of work, since the range being ioremapped doesn't intersect
system RAM at all.
With this change, ioremap on our 256 GiB BAR takes less than 1 second.
The modifications include:
1. Kconfig of Score: we don't support ioremap
2. Missed headfile including
3. There are some errors in other people's commit not checked by us, we fix it now
3.1 arch/score/kernel/entry.S: wrong instructions
3.2 arch/score/kernel/process.c : just some typos
When the rtmutex fast path is enabled the slow unlock function can
create the following situation:
spin_lock(foo->m->wait_lock);
foo->m->owner = NULL;
rt_mutex_lock(foo->m); <-- fast path
free = atomic_dec_and_test(foo->refcnt);
rt_mutex_unlock(foo->m); <-- fast path
if (free)
kfree(foo);
spin_unlock(foo->m->wait_lock); <--- Use after free.
Plug the race by changing the slow unlock to the following scheme:
while (!rt_mutex_has_waiters(m)) {
/* Clear the waiters bit in m->owner */
clear_rt_mutex_waiters(m);
owner = rt_mutex_owner(m);
spin_unlock(m->wait_lock);
if (cmpxchg(m->owner, owner, 0) == owner)
return;
spin_lock(m->wait_lock);
}
So in case of a new waiter incoming while the owner tries the slow
path unlock we have two situations:
is sufficient as all access to m->owner is serialized via
m->wait_lock;
Also document and clarify the wakeup_next_waiter function as suggested
by Oleg Nesterov.
Reported-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20140611183852.937945560@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even in the case when deadlock detection is not requested by the
caller, we can detect deadlocks. Right now the code stops the lock
chain walk and keeps the waiter enqueued, even on itself. Silly not to
yell when such a scenario is detected and to keep the waiter enqueued.
Return -EDEADLK unconditionally and handle it at the call sites.
The futex calls return -EDEADLK. The non futex ones dequeue the
waiter, throw a warning and put the task into a schedule loop.
Tagged for stable as it makes the code more robust.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Brad Mouring <bmouring@ni.com> Link: http://lkml.kernel.org/r/20140605152801.836501969@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we walk the lock chain, we drop all locks after each step. So the
lock chain can change under us before we reacquire the locks. That's
harmless in principle as we just follow the wrong lock path. But it
can lead to a false positive in the dead lock detection logic:
T0 holds L0
T0 blocks on L1 held by T1
T1 blocks on L2 held by T2
T2 blocks on L3 held by T3
T4 blocks on L4 held by T4
lock T2 -> lock L0 -> deadlock detected, but it's not a deadlock at all.
Brad tried to work around that in the deadlock detection logic itself,
but the more I looked at it the less I liked it, because it's crystal
ball magic after the fact.
We actually can detect a chain change very simple:
The current deadlock detection logic does not work reliably due to the
following early exit path:
/*
* Drop out, when the task has no waiters. Note,
* top_waiter can be NULL, when we are in the deboosting
* mode!
*/
if (top_waiter && (!task_has_pi_waiters(task) ||
top_waiter != task_top_pi_waiter(task)))
goto out_unlock_pi;
So this not only exits when the task has no waiters, it also exits
unconditionally when the current waiter is not the top priority waiter
of the task.
So in a nested locking scenario, it might abort the lock chain walk
and therefor miss a potential deadlock.
Simple fix: Continue the chain walk, when deadlock detection is
enabled.
We also avoid the whole enqueue, if we detect the deadlock right away
(A-A). It's an optimization, but also prevents that another waiter who
comes in after the detection and before the task has undone the damage
observes the situation and detects the deadlock and returns
-EDEADLOCK, which is wrong as the other task is not in a deadlock
situation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: Lai Jiangshan <laijs@cn.fujitsu.com> Link: http://lkml.kernel.org/r/20140522031949.725272460@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The per_cpu buffers are created one per possible CPU. But these do
not mean that those CPUs are online, nor do they even exist.
With the addition of the ring buffer polling, it assumes that the
caller polls on an existing buffer. But this is not the case if
the user reads trace_pipe from a CPU that does not exist, and this
causes the kernel to crash.
Simple fix is to check the cpu against buffer bitmask against to see
if the buffer was allocated or not and return -ENODEV if it is
not.
More updates were done to pass the -ENODEV back up to userspace.
When we set the valid bit on invalid GART entries they are
loaded into the TLB when an adjacent entry is loaded. This
poisons the TLB with invalid entries which are sometimes
not correctly removed on TLB flush.
For stable inclusion the patch probably needs to be modified a bit.
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first time that we allocate from an uninitialized inode allocation
bitmap, if the block allocation bitmap is also uninitalized, we need
to get write access to the block group descriptor before we start
modifying the block group descriptor flags and updating the free block
count, etc. Otherwise, there is the potential of a bad journal
checksum (if journal checksums are enabled), and of the file system
becoming inconsistent if we crash at exactly the wrong time.
There's a race condition between the atomic_dec_and_test(&io->count)
in dec_count() and the waking of the sync_io() thread. If the thread
is spuriously woken immediately after the decrement it may exit,
making the on stack io struct invalid, yet the dec_count could still
be using it.
Fix this race by using a completion in sync_io() and dec_count().
Reported-by: Minfei Huang <huangminfei@ucloud.cn> Signed-off-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Win8, we have implemented several optimizations to improve the
scalability and performance of the VMBUS transport between the Host and the
Guest. Some of the non-performance critical services cannot leverage these
optimization since they only read and process one message at a time.
Make adjustments to the callback dispatch code to account for the way
non-performance critical drivers handle reading of the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/linux/sched.h implements TASK_SIZE_OF as TASK_SIZE if it
is not set by the architecture headers. TASK_SIZE uses the
current task to determine the size of the virtual address space.
On a 64-bit kernel this will cause reading /proc/pid/pagemap of a
64-bit process from a 32-bit process to return EOF when it reads
past 0xffffffff.
Implement TASK_SIZE_OF exactly the same as TASK_SIZE with
test_tsk_thread_flag instead of test_thread_flag.
Signed-off-by: Colin Cross <ccross@android.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Byte-to-bit-count computation is only partly converted to big-endian and is
mixing in CPU-endian values. Problem was noticed by sparce with warning:
CHECK arch/x86/crypto/sha512_ssse3_glue.c
arch/x86/crypto/sha512_ssse3_glue.c:144:19: warning: restricted __be64 degrades to integer
arch/x86/crypto/sha512_ssse3_glue.c:144:17: warning: incorrect type in assignment (different base types)
arch/x86/crypto/sha512_ssse3_glue.c:144:17: expected restricted __be64 <noident>
arch/x86/crypto/sha512_ssse3_glue.c:144:17: got unsigned long long
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commtit 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to
drivers/cpufreq) this added dependancy only for CONFIG_ARCH_DAVINCI_DA850
where as davinci_cpufreq_init() call is used by all davinci platform.
This patch fixes following build error:
arch/arm/mach-davinci/built-in.o: In function `davinci_init_late':
:(.init.text+0x928): undefined reference to `davinci_cpufreq_init'
make: *** [vmlinux] Error 1
Fixes: 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to drivers/cpufreq) Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On POWER8 when switching to a KVM guest we set bits in MMCR2 to freeze
the PMU counters. Aside from on boot they are then never reset,
resulting in stuck perf counters for any user in the guest or host.
We now set MMCR2 to 0 whenever enabling the PMU, which provides a sane
state for perf to use the PMU counters under either the guest or the
host.
This was manifesting as a bug with ppc64_cpu --frequency:
$ sudo ppc64_cpu --frequency
WARNING: couldn't run on cpu 0
WARNING: couldn't run on cpu 8
...
WARNING: couldn't run on cpu 144
WARNING: couldn't run on cpu 152
min: 18446744073.710 GHz (cpu -1)
max: 0.000 GHz (cpu -1)
avg: 0.000 GHz
The command uses a perf counter to measure CPU cycles over a fixed
amount of time, in order to approximate the frequency of the machine.
The counters were returning zero once a guest was started, regardless of
weather it was still running or had been shut down.
By dumping the value of MMCR2, it was observed that once a guest is
running MMCR2 is set to 1s - which stops counters from running:
This is done unconditionally in book3s_hv_interrupts.S upon entering the
guest, and the original value is only save/restored if the host has
indicated it was using the PMU. This is okay, however the user of the
PMU needs to ensure that it is in a defined state when it starts using
it.
Fixes: e05b9b9e5c10 ("powerpc/perf: Power8 PMU support") Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of separate bits for every POWER8 PMU feature, have a single one
for v2.07 of the architecture.
This saves us adding a MMCR2 define for a future patch.
Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking closer, the active PMC is 0 at this point and we took a PMU
exception on the transition from negative to 0. Some versions of POWER8
have an issue where they edge detect and not level detect PMC overflows.
A number of places program the PMC with (0x80000000 - period_left),
where period_left can be negative. We can either fix all of these or
just ensure that period_left is always >= 1.
This patch takes the second option.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change has caused a regression in (at least) serial port detection
for a number of machines (see LP#1313981 [1]). These seem to represent
their IO regions (presumably incorrectly) as a zero length region.
Reverting the above commit restores these serial devices.
Only elide zero length resources which lie at address 0.
Fixes: b355cee88e3b (ACPI / resources: ignore invalid ACPI device resources) Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module test script for the adm1021 driver exposes a cache problem
when writing temperature limits. temp_min and temp_max are expected
to be stored in milli-degrees C but are stored in degrees C.
Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writing to fanX_div does not clear the cache. As a result, reading
from fanX_div may return the old value for up to two seconds
after writing a new value.
This patch ensures the fan_div cache is updated in set_fan_div().
Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upper limit for write operations to temperature limit registers
was clamped to a fractional value. However, limit registers do
not support fractional values. As a result, upper limits of 127.5
degrees C or higher resulted in a rounded limit of 128 degrees C.
Since limit registers are signed, this was stored as -128 degrees C.
Clamp limits to (-55, +127) degrees C to solve the problem.
Value on writes to auto_temp[12]_min and auto_temp[12]_max were not
clamped at all, but masked. As a result, out-of-range writes resulted
in a more or less arbitrary limit. Clamp those attributes to (0, 127)
degrees C for more predictable results.
Cc: Axel Lin <axel.lin@ingics.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In my investigation, I found the root cause is wq_numa_possible_cpumask.
All entries of wq_numa_possible_cpumask is allocated by
alloc_cpumask_var_node(). And these entries are used without initializing.
So these entries have wrong value.
When hot-adding and onlining CPU, wq_update_unbound_numa() is called.
wq_update_unbound_numa() calls alloc_unbound_pwq(). And alloc_unbound_pwq()
calls get_unbound_pool(). In get_unbound_pool(), worker_pool->node is set
as follow:
3592 /* if cpumask is contained inside a NUMA node, we belong to that node */
3593 if (wq_numa_enabled) {
3594 for_each_node(node) {
3595 if (cpumask_subset(pool->attrs->cpumask,
3596 wq_numa_possible_cpumask[node])) {
3597 pool->node = node;
3598 break;
3599 }
3600 }
3601 }
But wq_numa_possible_cpumask[node] does not have correct cpumask. So, wrong
node is selected. As a result, kernel panic occurs.
By this patch, all entries of wq_numa_possible_cpumask are allocated by
zalloc_cpumask_var_node to initialize them. And the panic disappeared.
The cause is that cpuset_mems_allowed() try to take
mutex_lock(&callback_mutex) under the rcu_read_lock(which was hold in
__mpol_dup()). And in cpuset_mems_allowed(), the access to cpuset is
under rcu_read_lock, so in __mpol_dup, we can reduce the rcu_read_lock
protection region to protect the access to cpuset only in
current_cpuset_is_being_rebound(). So that we can avoid this bug.
This patch is a temporary solution that just addresses the bug
mentioned above, can not fix the long-standing issue about cpuset.mems
rebinding on fork():
"When the forker's task_struct is duplicated (which includes
->mems_allowed) and it races with an update to cpuset_being_rebound
in update_tasks_nodemask() then the task's mems_allowed doesn't get
updated. And the child task's mems_allowed can be wrong if the
cpuset's nodemask changes before the child has been added to the
cgroup's tasklist."
Corsair USB Dongles are shipped with Corsair AXi series PSUs.
These are cp210x serial usb devices, so make driver detect these.
I have a program, that can get information from these PSUs.
Tested with 2 different dongles shipped with Corsair AX860i and
AX1200i units.
In v2.6.34 commit 9d8cebd4bcd7 ("mm: fix mbind vma merge problem")
introduced vma merging to mbind(), but it should have also changed the
convention of passing start vma from queue_pages_range() (formerly
check_range()) to new_vma_page(): vma merging may have already freed
that structure, resulting in BUG at mm/mempolicy.c:1738 and probably
worse crashes.
There's a race between fork() and hugepage migration, as a result we try
to "dereference" a swap entry as a normal pte, causing kernel panic.
The cause of the problem is that copy_hugetlb_page_range() can't handle
"swap entry" family (migration entry and hwpoisoned entry) so let's fix
it.
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.
When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.
This function aborts them with DID_SOFT_ERROR.
If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.
The result is that disk returning QUEUE FULL causes request failures.
The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags. The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags. The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function unifb_mmap calls functions which are defined in linux/mm.h
and asm/pgtable.h
The related error (for unicore32 with unicore32_defconfig):
CC drivers/video/fbdev/fb-puv3.o
drivers/video/fbdev/fb-puv3.c: In function 'unifb_mmap':
drivers/video/fbdev/fb-puv3.c:646: error: implicit declaration of
function 'vm_iomap_memory'
drivers/video/fbdev/fb-puv3.c:646: error: implicit declaration of
function 'pgprot_noncached'
Signed-off-by: Zhichuang Sun <sunzc522@gmail.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Joe Perches <joe@perches.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-fbdev@vger.kernel.org Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need include "asm/pgtable.h" to include "asm-generic/pgtable-nopmd.h",
so can let 'pmd_t' defined. The related error with allmodconfig:
CC arch/unicore32/mm/alignment.o
In file included from arch/unicore32/mm/alignment.c:24:
arch/unicore32/include/asm/tlbflush.h:135: error: expected .). before .*. token
arch/unicore32/include/asm/tlbflush.h:154: error: expected .). before .*. token
In file included from arch/unicore32/mm/alignment.c:27:
arch/unicore32/mm/mm.h:15: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
arch/unicore32/mm/mm.h:20: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
arch/unicore32/mm/mm.h:25: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
make[1]: *** [arch/unicore32/mm/alignment.o] Error 1
make: *** [arch/unicore32/mm] Error 2
Causes the ratelimiting to spam the kernel log with the "callbacks suppressed"
message below, even while the dev_dbg it is supposed to rate limit wouldn't
print anything because DEBUG is not defined for this device.
Commit c49436b657d0 (serial: 8250_dw: Improve unwritable LCR workaround)
caused a regression. It added a check that the LCR was written properly
to detect and workaround the busy quirk, but the behaviour of bit 5
(UART_LCR_SPAR) differs between IP versions 3.00a and 3.14c per the
docs. On older versions this caused the check to fail and it would
repeatedly force idle and rewrite the LCR register, causing delays and
preventing any input from serial being received.
This is fixed by masking out UART_LCR_SPAR before making the comparison.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Tim Kryger <tim.kryger@linaro.org> Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Matt Porter <matt.porter@linaro.org> Cc: Markus Mayer <markus.mayer@linaro.org> Tested-by: Tim Kryger <tim.kryger@linaro.org> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Wang Nan <wangnan0@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configured with UART_16550_COMPATIBLE=NO or in versions prior to
the introduction of this option, the Designware UART will ignore writes
to the LCR if the UART is busy. The current workaround saves a copy of
the last written LCR and re-writes it in the ISR for a special interrupt
that is raised when a write was ignored.
Unfortunately, interrupts are typically disabled prior to performing a
sequence of register writes that include the LCR so the point at which
the retry occurs is too late. An example is serial8250_do_set_termios()
where an ignored LCR write results in the baud divisor not being set and
instead a garbage character is sent out the transmitter.
Furthermore, since serial_port_out() offers no way to indicate failure,
a serious effort must be made to ensure that the LCR is actually updated
before returning back to the caller. This is difficult, however, as a
UART that was busy during the first attempt is likely to still be busy
when a subsequent attempt is made unless some extra action is taken.
This updated workaround reads back the LCR after each write to confirm
that the new value was accepted by the hardware. Should the hardware
ignore a write, the TX/RX FIFOs are cleared and the receive buffer read
before attempting to rewrite the LCR out of the hope that doing so will
force the UART into an idle state. While this may seem unnecessarily
aggressive, writes to the LCR are used to change the baud rate, parity,
stop bit, or data length so the data that may be lost is likely not
important. Admittedly, this is far from ideal but it seems to be the
best that can be done given the hardware limitations.
Lastly, the revised workaround doesn't touch the LCR in the ISR, so it
avoids the possibility of a "serial8250: too much work for irq" lock up.
This problem is rare in real situations but can be reproduced easily by
wiring up two UARTs and running the following commands.
[ 27.700000] serial8250: too much work for irq96
[ 27.700000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.740000] serial8250: too much work for irq96
Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Reviewed-by: Matt Porter <matt.porter@linaro.org> Reviewed-by: Markus Mayer <markus.mayer@linaro.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[wangnan: backport to 3.10.43:
- adjust context
- remove unneeded local var] Signed-off-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is configured for RTS/CTS flow control, serial core
will disable the transmitter if it observes CTS is de-asserted. This is
perfectly reasonable and appropriate when the UART lacks the ability to
automatically perform CTS flow control.
However, if the UART hardware can manage flow control automatically, it
is important that software not get involved. When the DesignWare UART
enables 16C750 style auto-RTS/CTS it stops generating interrupts for
changes in CTS state so software mostly stays out of the way. However,
it does report the true state of CTS in the MSR so software may notice
it is de-asserted and respond by improperly disabling the transmitter.
Once this happens the transmitter will be blocked forever.
To avoid this situation, we simply lie to the 8250 and serial core by
reporting that CTS is asserted whenever auto-RTS/CTS mode is enabled.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org> Reviewed-by: Matt Porter <matt.porter@linaro.org> Reviewed-by: Markus Mayer <markus.mayer@linaro.org> Cc: Wang Nan <wangnan0@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
a27fbf2f067b0cd ("mmc: add ignorance case for CMD13 CRC error") produced
a cmd.flags unhandled in realtek pci host driver. This will make MMC
card fail to initialize, this patch is used to handle the new cmd.flags
condition and MMC card can be used.
The ras3 block on spear320 claims to have 3 interrupts. In fact it has
one and 6 reserved interrupts. Account the 6 reserved to this block so
it has 7 interrupts total. That matches the datasheet and the device
tree entries.
Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move
the shared irq multiplexor to DT). Testing is overrated....
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de Fixes: 80515a5a2e3c ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT') Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we write to a degraded array which has a bitmap, we
make sure the relevant bit in the bitmap remains set when
the write completes (so a 're-add' can quickly rebuilt a
temporarily-missing device).
If, immediately after such a write starts, we incorporate a spare,
commence recovery, and skip over the region where the write is
happening (because the 'needs recovery' flag isn't set yet),
then that write will not get to the new device.
Once the recovery finishes the new device will be trusted, but will
have incorrect data, leading to possible corruption.
We cannot set the 'needs recovery' flag when we start the write as we
do not know easily if the write will be "degraded" or not. That
depends on details of the particular raid level and particular write
request.
This patch fixes a corruption issue of long standing and so it
suitable for any -stable kernel. It applied correctly to 3.0 at
least and will minor editing to earlier kernels.
Reported-by: Bill <billstuff2001@sbcglobal.net> Tested-by: Bill <billstuff2001@sbcglobal.net> Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disabling reading and writing to the trace file should not be able to
disable all function tracing callbacks. There's other users today
(like kprobes and perf). Reading a trace file should not stop those
from happening.
It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format. Fix by wrapping the numbers in
cpu_to_le32.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An NFS operation that creates a new symlink includes the symlink data,
which is xdr-encoded as a length followed by the data plus 0 to 3 bytes
of zero-padding as required to reach a 4-byte boundary.
The vfs, on the other hand, wants null-terminated data.
The simple way to handle this would be by copying the data into a newly
allocated buffer with space for the final null.
The current nfsd_symlink code tries to be more clever by skipping that
step in the (likely) case where the byte following the string is already
0.
But that assumes that the byte following the string is ours to look at.
In fact, it might be the first byte of a page that we can't read, or of
some object that another task might modify.
Worse, the NFSv4 code tries to fix the problem by actually writing to
that byte.
In the NFSv2/v3 cases this actually appears to be safe:
- nfs3svc_decode_symlinkargs explicitly null-terminates the data
(after first checking its length and copying it to a new
page).
- NFSv2 limits symlinks to 1k. The buffer holding the rpc
request is always at least a page, and the link data (and
previous fields) have maximum lengths that prevent the request
from reaching the end of a page.
In the NFSv4 case the CREATE op is potentially just one part of a long
compound so can end up on the end of a page if you're unlucky.
The minimal fix here is to copy and null-terminate in the NFSv4 case.
The nfsd_symlink() interface here seems too fragile, though. It should
really either do the copy itself every time or just require a
null-terminated string.
Reported-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in the inkern.c code for IIO framework, the function
of_iio_channel_get_by_name() will return a non-NULL pointer when
it cannot find a channel using of_iio_channel_get() and when it
tries to search for 'io-channel-ranges' property and fails. This
is incorrect behaviour as the function which calls this expects
a NULL pointer for failure. This patch rectifies the issue.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent Intel CPUs have 10 variable range MTRRs. Since operating systems
sometime make assumptions on CPUs while they ignore capability MSRs, it is
better for KVM to be consistent with recent CPUs. Reporting more MTRRs than
actually supported has no functional implications.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hole punching code for files with indirect blocks wrongly computed
number of blocks which need to be cleared when traversing the indirect
block tree. That could result in punching more blocks than actually
requested and thus effectively cause a data loss. For example:
Error recovery in ext4_alloc_branch() calls ext4_forget() even for
buffer corresponding to indirect block it did not allocate. This leads
to brelse() being called twice for that buffer (once from ext4_forget()
and once from cleanup in ext4_ind_map_blocks()) leading to buffer use
count misaccounting. Eventually (but often much later because there
are other users of the buffer) we will see messages like:
VFS: brelse: Trying to free free buffer
Another manifestation of this problem is an error:
JBD2 unexpected failure: jbd2_journal_revoke: !buffer_revoked(bh);
inconsistent data on disk
The fix is easy - don't forget buffer we did not allocate. Also add an
explanatory comment because the indexing at ext4_alloc_branch() is
somewhat subtle.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we SMB3 mounted with mapchars (to allow reserved characters : \ / > < * ?
via the Unicode Windows to POSIX remap range) empty paths
(eg when we open "" to query the root of the SMB3 directory on mount) were not
null terminated so we sent garbarge as a path name on empty paths which caused
SMB2/SMB2.1/SMB3 mounts to fail when mapchars was specified. mapchars is
particularly important since Unix Extensions for SMB3 are not supported (yet)
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for firmware rev 508+ was added years ago, but we never noticed
it reports channel in a different way for G-PHY devices. Instead of
offset from 2400 MHz it simply passes channel id (AKA hw_value).
So far it was (most probably) affecting monitor mode users only, but
the following recent commit made it noticeable for quite everybody:
The value of ESR has been stored into x1, and should be directly pass to
do_sp_pc_abort function, "MOV x1, x25" is an extra operation and do_sp_pc_abort
will get the wrong value of ESR.
Fix a parser-bug in the omap2 muxing code where muxtable-entries will be
wrongly selected if the requested muxname is a *prefix* of their
m0-entry and they have a matching mN-entry. Fix by additionally checking
that the length of the m0_entry is equal.
For example muxing of "dss_data2.dss_data2" on omap32xx will fail
because the prefix "dss_data2" will match the mux-entries "dss_data2" as
well as "dss_data20", with the suffix "dss_data2" matching m0 (for
dss_data2) and m4 (for dss_data20). Thus both are recognized as signal
path candidates:
This will result in a failure to mux the pin at all:
_omap_mux_get_by_name: Multiple signal paths (2) for dss_data2.dss_data2
Patch should apply to linus' latest master down to rather old linux-2.6
trees.
Signed-off-by: David R. Piegdon <lkml@p23q.org> Cc: stable@vger.kernel.org
[tony@atomide.com: updated description to include full description] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / people / ms / linux.git / log
