Marek Vasut [Tue, 20 Jun 2023 10:27:13 +0000 (12:27 +0200)]
mmc: Add MMC_QUIRK_BROKEN_SD_CACHE for Kingston Canvas Go Plus from 11/2019
This microSD card never clears Flush Cache bit after cache flush has
been started in sd_flush_cache(). This leads e.g. to failure to mount
file system. Add a quirk which disables the SD cache for this specific
card from specific manufacturing date of 11/2019, since on newer dated
cards from 05/2023 the cache flush works correctly.
Fixes: 08ebf903af57 ("mmc: core: Fixup support for writeback-cache for eMMC and SD") Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20230620102713.7701-1-marex@denx.de Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Robert Marko [Mon, 19 Jun 2023 19:35:58 +0000 (21:35 +0200)]
mmc: core: disable TRIM on Kingston EMMC04G-M627
It seems that Kingston EMMC04G-M627 despite advertising TRIM support does
not work when the core is trying to use REQ_OP_WRITE_ZEROES.
We are seeing I/O errors in OpenWrt under 6.1 on Zyxel NBG7815 that we did
not previously have and tracked it down to REQ_OP_WRITE_ZEROES.
Trying to use fstrim seems to also throw errors like:
[93010.835112] I/O error, dev loop0, sector 16902 op 0x3:(DISCARD) flags 0x800 phys_seg 1 prio class 2
Disabling TRIM makes the error go away, so lets add a quirk for this eMMC
to disable TRIM.
Yann Gautier [Mon, 19 Jun 2023 11:51:20 +0000 (13:51 +0200)]
mmc: mmci: stm32: add delay block support for STM32MP25
On STM32MP25, the delay block is inside the SoC, and configured through
the SYSCFG registers. The algorithm is also different from what was in
STM32MP1 chip.
Yann Gautier [Mon, 19 Jun 2023 11:51:18 +0000 (13:51 +0200)]
mmc: mmci: stm32: manage block gap hardware flow control
In stm32 sdmmc variant revision v3.0, a block gap hardware flow control
should be used with bus speed modes SDR104 and HS200.
It is enabled by writing a non-null value to the new added register
MMCI_STM32_FIFOTHRR.
The threshold will be 2^(N-1) bytes, so we can use the ffs() function to
compute the value N to be written to the register. The threshold used
should be the data block size, but must not be bigger than the FIFO size.
Yann Gautier [Mon, 19 Jun 2023 11:51:16 +0000 (13:51 +0200)]
mmc: mmci: add stm32_idmabsize_align parameter
The alignment for the IDMA size depends on the peripheral version, it
should then be configurable. Add stm32_idmabsize_align in the variant
structure.
And remove now unused (and wrong) MMCI_STM32_IDMABNDT_* macros.
For STM32MP25, we'll need to distinguish how is managed the delay block.
This is done through a new comptible dedicated for this SoC, as the
delay block registers are located in SYSCFG peripheral.
Robert Marko [Tue, 30 May 2023 21:32:59 +0000 (23:32 +0200)]
mmc: core: disable TRIM on Micron MTFC4GACAJCN-1M
It seems that Micron MTFC4GACAJCN-1M despite advertising TRIM support does
not work when the core is trying to use REQ_OP_WRITE_ZEROES.
We are seeing the following errors in OpenWrt under 6.1 on Qnap Qhora 301W
that we did not previously have and tracked it down to REQ_OP_WRITE_ZEROES:
[ 18.085950] I/O error, dev loop0, sector 596 op 0x9:(WRITE_ZEROES) flags 0x800 phys_seg 0 prio class 2
Disabling TRIM makes the error go away, so lets add a quirk for this eMMC
to disable TRIM.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:22 +0000 (23:36 +0300)]
mmc: usdhi60rol0: fix deferred probing
The driver overrides the error codes returned by platform_get_irq_byname()
to -ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating error
codes upstream.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:21 +0000 (23:36 +0300)]
mmc: sunxi: fix deferred probing
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:20 +0000 (23:36 +0300)]
mmc: sh_mmcif: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:19 +0000 (23:36 +0300)]
mmc: sdhci-spear: fix deferred probing
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:18 +0000 (23:36 +0300)]
mmc: sdhci-acpi: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 1b7ba57ecc86 ("mmc: sdhci-acpi: Handle return value of platform_get_irq") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20230617203622.6812-9-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:17 +0000 (23:36 +0300)]
mmc: owl: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:16 +0000 (23:36 +0300)]
mmc: omap_hsmmc: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:15 +0000 (23:36 +0300)]
mmc: omap: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:14 +0000 (23:36 +0300)]
mmc: mvsdio: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:13 +0000 (23:36 +0300)]
mmc: mtk-sd: fix deferred probing
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:12 +0000 (23:36 +0300)]
mmc: meson-gx: fix deferred probing
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Sergey Shtylyov [Sat, 17 Jun 2023 20:36:11 +0000 (23:36 +0300)]
mmc: bcm2835: fix deferred probing
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -EINVAL, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the error
codes upstream. Since commit ce753ad1549c ("platform: finally disallow IRQ0
in platform_get_irq() and its ilk") IRQ0 is no longer returned by those APIs,
so we now can safely ignore it...
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.") Cc: stable@vger.kernel.org # v5.19+ Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20230617203622.6812-2-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang [Sat, 17 Jun 2023 08:53:19 +0000 (16:53 +0800)]
mmc: litex_mmc: set PROBE_PREFER_ASYNCHRONOUS
mmc host drivers should have enabled the asynchronous probe option, but
it seems like we didn't set it for litex_mmc when introducing litex mmc
support, so let's set it now.
Tested with linux-on-litex-vexriscv on sipeed tang nano 20K fpga.
Linus Walleij [Fri, 16 Jun 2023 20:42:27 +0000 (22:42 +0200)]
mmc: mmci: Break out a helper function
These four lines clearing, masking and resetting the state
of the busy detect state machine is repeated five times in
the code so break this out to a small helper so things are
easier to read.
Linus Walleij [Fri, 16 Jun 2023 20:42:24 +0000 (22:42 +0200)]
mmc: mmci: Retry the busy start condition
This makes the ux500 ->busy_complete() callback re-read
the status register 10 times while waiting for the busy
signal to assert in the status register.
If this does not happen, we bail out regarding the
command completed already, i.e. before we managed to
start to check the busy status.
There is a comment in the code about this, let's just
implement it to be certain that we can catch this glitch
if it happens.
Linus Walleij [Fri, 16 Jun 2023 20:42:23 +0000 (22:42 +0200)]
mmc: mmci: Make busy complete state machine explicit
This refactors the ->busy_complete() callback currently
only used by Ux500 and STM32 to handle busy detection on
hardware where one and the same IRQ is fired whether we get
a start or an end signal on busy detect.
The code is currently using the cached status from the
command IRQ in ->busy_status as a state to select what to
do next: if this state is non-zero we are waiting for
IRQs and if it is zero we treat the state as the starting
point for a busy detect wait cycle.
Make this explicit by creating a state machine where the
->busy_complete callback moves between three states.
The Ux500 busy detect code currently assumes this order:
we enable the busy detect IRQ, get a busy start IRQ, then a
busy end IRQ, and then we clear and mask this IRQ and
proceed.
We insert debug prints for unexpected states.
This works as before on most cards, however on a
problematic card that is not working with busy detect, and
which I have been debugging, the following happens a lot:
[ 3.380554] mmci-pl18x 80005000.mmc: no busy signalling in time
[ 3.387420] mmci-pl18x 80005000.mmc: no busy signalling in time
[ 3.394561] mmci-pl18x 80005000.mmc: lost busy status
when waiting for busy start IRQ
This probably means that the busy detect start IRQ has
already occurred when we start executing the
->busy_complete() callbacks, and the busy detect end IRQ
is counted as the start IRQ, and this is what is causing
the card to not be detected properly.
Linus Walleij [Fri, 16 Jun 2023 20:42:22 +0000 (22:42 +0200)]
mmc: mmci: Break out error check in busy detect
The busy detect callback for Ux500 checks for an error
in the status in the first if() clause. The only practical
reason is that if an error occurs, the if()-clause is not
executed, and the code falls through to the last
if()-clause if (host->busy_status) which will clear and
disable the irq. Make this explicit instead: it is easier
to read.
Linus Walleij [Fri, 16 Jun 2023 20:42:19 +0000 (22:42 +0200)]
mmc: mmci: Clear busy_status when starting command
If we are starting a command which can generate a busy
response, then clear the variable host->busy_status
if the variant is using a ->busy_complete callback.
We are lucky that the member is zero by default and
hopefully always gets cleared in the ->busy_complete
callback even on errors, but it's just fragile so
make sure it is always initialized to zero.
Yann Gautier [Tue, 13 Jun 2023 15:01:48 +0000 (17:01 +0200)]
mmc: mmci: stm32: set feedback clock when using delay block
The feedback clock is used only for SDR104 & HS200 modes, and when
delay block is used (frequency is higher than 50 MHz). The tuning
procedure is then only required for those modes. Skip the procedure
for other modes.
The setting of this feedback clock is done just after enabling delay
block, and before configuring it.
mmc: meson-gx: remove redundant mmc_request_done() call from irq context
The call to mmc_request_done() can schedule, so it must not be called
from irq context. Wake the irq thread if it needs to be called, and let
its existing logic do its work.
mmc: mmci: stm32: fix max busy timeout calculation
The way that the timeout is currently calculated could lead to a u64
timeout value in mmci_start_command(). This value is then cast in a u32
register that leads to mmc erase failed issue with some SD cards.
Dennis Zhou [Wed, 29 Mar 2023 23:48:01 +0000 (16:48 -0700)]
mmc: core: Allow mmc_start_host() synchronously detect a card
When using dm-verity with a data partition on an emmc device, dm-verity
races with the initialization of the (e)MMC/SD cards. This is because the
card detection procedure is being managed from a workqueue, rather than
synchronously from the mmc host's ->probe() routine.
To allow the card detect to be synchronous, let's simply skip using the
workqueue at the first initialization attempt from mmc_start_host().
Signed-off-by: Dennis Zhou <dennis@kernel.org> Link: https://lore.kernel.org/r/ZCTOMVjW+pnZVGsQ@snowbird
[Ulf: Re-wrote the commit message to clarify the change] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stephan Gerhold [Thu, 18 May 2023 09:39:36 +0000 (11:39 +0200)]
mmc: sdhci-msm: Disable broken 64-bit DMA on MSM8916
While SDHCI claims to support 64-bit DMA on MSM8916 it does not seem to
be properly functional. It is not immediately obvious because SDHCI is
usually used with IOMMU bypassed on this SoC, and all physical memory
has 32-bit addresses. But when trying to enable the IOMMU it quickly
fails with an error such as the following:
Looking closely it's obvious that only the 32-bit part of the address
(0xfffff200) arrives at the SMMU, the higher 16-bit (0xffff...) get
lost somewhere. This might not be a limitation of the SDHCI itself but
perhaps the bus/interconnect it is connected to, or even the connection
to the SMMU.
Work around this by setting SDHCI_QUIRK2_BROKEN_64_BIT_DMA to avoid
using 64-bit addresses.
Abel Vesa [Sat, 8 Apr 2023 21:40:41 +0000 (00:40 +0300)]
mmc: sdhci-msm: Switch to the new ICE API
Now that there is a new dedicated ICE driver, drop the sdhci-msm ICE
implementation and use the new ICE api provided by the Qualcomm soc
driver ice. The platforms that already have ICE support will use the
API as library since there will not be a devicetree node, but instead
they have reg range. In this case, the of_qcom_ice_get will return an
ICE instance created for the consumer's device. But if there are
platforms that do not have ice reg in the consumer devicetree node
and instead provide a dedicated ICE devicetree node, theof_qcom_ice_get
will look up the device based on qcom,ice property and will get the ICE
instance registered by the probe function of the ice driver.
The ICE clock is now handle by the new driver. This is done by enabling
it on the creation of the ICE instance and then enabling/disabling it on
SDCC runtime resume/suspend.
Victor Shih [Fri, 9 Jun 2023 07:14:41 +0000 (15:14 +0800)]
mmc: sdhci-pci-gli: Add support SD Express card for GL9767
Add support SD Express card for GL9767. The workflow of the
SD Express card in GL9767 is as below.
1. GL9767 operates in SD mode and set MMC_CAP2_SD_EXP flag.
2. If card is inserted, Host send CMD8 to ask the capabilities
of the card.
3. If the card has PCIe capability, then init_sd_express()
will be invoked.
4. If the card has been put in write protect state then the
SD features supported by SD mode but not supported by
PCIe mode, therefore GL9767 switch to SD mode.
5. If the card has not been put in write protect state then
GL9767 switch from SD mode to PCIe/NVMe mode and mmc driver
handover control to NVMe driver.
6. If card is removed, GL9767 will return to SD mode.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20230609071441.451464-5-victorshihgli@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Victor Shih [Fri, 9 Jun 2023 07:14:38 +0000 (15:14 +0800)]
mmc: sdhci-pci-gli: Add Genesys Logic GL9767 support
Add support for the GL9767 chipset. GL9767 supports
SD3 mode likes UHS-I SDR50, SDR104.
Enable MSI interrupt for GL9767. Some platform do not
support PCI INTx and devices can not work without
interrupt.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20230609071441.451464-2-victorshihgli@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wenbin Mei [Fri, 9 Jun 2023 10:13:55 +0000 (18:13 +0800)]
mmc: mtk-sd: reduce CIT for better performance
CQHCI_SSC1 indicates to CQE the polling period to use when using periodic
SEND_QUEUE_STATUS(CMD13) polling.
Since MSDC CQE uses msdc_hclk as ITCFVAL, so driver should use hclk
frequency to get the actual time.
The default value 0x1000 that corresponds to 150us for MediaTek SoCs, let's
decrease it to 0x40 that corresponds to 2.35us, which can improve the
performance of some eMMC devices.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com> Link: https://lore.kernel.org/r/20230609101355.5220-2-wenbin.mei@mediatek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christian Loehle [Thu, 25 May 2023 09:56:04 +0000 (09:56 +0000)]
mmc: block: ioctl: do write error check for spi
SPI doesn't have the usual PROG path we can check for error bits
after moving back to TRAN. Instead it holds the line LOW until
completion. We can then check if the card shows any errors or
is in IDLE state, indicating the line is no longer LOW because
the card was reset.
Chevron Li [Tue, 23 May 2023 11:11:14 +0000 (19:11 +0800)]
mmc: sdhci: fix DMA configure compatibility issue when 64bit DMA mode is used.
Bayhub SD host has hardware limitation:
1.The upper 32bit address is inhibited to be written at SD Host Register
[03E][13]=0 (32bits addressing) mode, is admitted to be written only at
SD Host Register [03E][13]=1 (64bits addressing) mode.
2.Because of above item#1, need to configure SD Host Register [03E][13] to
1(64bits addressing mode) before set 64bit ADMA system address's higher
32bits SD Host Register [05F~05C] if 64 bits addressing mode is used.
The hardware limitation is reasonable for below reasons:
1.Normal flow should set DMA working mode first, then do
DMA-transfer-related configuration, such as system address.
2.The hardware limitation may avoid the software to configure wrong higher
32bit address at 32bits addressing mode although it is redundant.
The change that set 32bits/64bits addressing mode before set ADMA address,
has no side-effect to other host IPs for below reason:
The setting order is reasonable and standard: DMA Mode setting first and
then DMA address setting. It meets all DMA setting sequence.
Yeqi Fu [Thu, 18 May 2023 10:12:16 +0000 (18:12 +0800)]
mmc: core: Remove unnecessary error checks and change return type
The error checks in mmc_blk_add_debugfs() and mmc_blk_remove_debugfs()
are extraneous. Therefore, this patch removes all error checks from
both functions.
Additionally, mmc_blk_add_debugfs() has been changed to return void
instead of an integer value that was never used. This simplifies the
function and improves its clarity.
Arnd Bergmann [Tue, 16 May 2023 20:27:04 +0000 (22:27 +0200)]
memstick r592: make memstick_debug_get_tpc_name() static
There are no other files referencing this function, apparently
it was left global to avoid an 'unused function' warning when
the only caller is left out. With a 'W=1' build, it causes
a 'missing prototype' warning though:
drivers/memstick/host/r592.c:47:13: error: no previous prototype for 'memstick_debug_get_tpc_name' [-Werror=missing-prototypes]
Annotate the function as 'static __maybe_unused' to avoid both
problems.
Douglas Anderson [Wed, 10 May 2023 13:44:54 +0000 (06:44 -0700)]
mmc: mediatek: Avoid ugly error message when SDIO wakeup IRQ isn't used
When I boot a kukui-kodama board, I see an ugly warning in my kernel
log:
mtk-msdc 11240000.mmc: error -ENXIO: IRQ sdio_wakeup not found
It's pretty normal not to have an "sdio_wakeup" IRQ defined. In fact,
no device trees in mainline seem to have it. Let's use the
platform_get_irq_byname_optional() to avoid the error message.
Simon Horman [Wed, 10 May 2023 12:39:00 +0000 (14:39 +0200)]
mmc: meson-mx-sdhc: Avoid cast to incompatible function type
Rather than casting mmc_free_host to an incompatible function type,
provide a trivial wrapper with the correct signature for the use-case.
Reported by clang-16 with W=1:
.../meson-mx-sdhc-mmc.c:791:38: error: cast from 'void (*)(struct mmc_host *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
ret = devm_add_action_or_reset(dev, (void(*)(void *))mmc_free_host,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/device.h:265:38: note: expanded from macro 'devm_add_action_or_reset'
__devm_add_action_or_reset(release, action, data, #action)
^~~~~~
The same approach is taken in litex_mmc.c with the function
litex_mmc_free_host_wrapper(). There may be scope for consolidation.
No functional change intended.
Compile tested only.
mmc: dw_mmc: Make dw_mci_pltfm_remove() return void
dw_mci_pltfm_remove() returned zero unconditionally. Make it return void
instead which makes its semantics a bit clearer.
Convert the drivers that use this function as .remove() callback to
.remove_new() which has the right prototype. This helps getting rid of
the platform_driver's remove callback that returns an int (which is
error prone). The other users didn't check the return value anyhow.
Linus Torvalds [Sun, 11 Jun 2023 17:14:02 +0000 (10:14 -0700)]
Merge tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Borislav Petkov:
- Set up the kernel CS earlier in the boot process in case EFI boots
the kernel after bypassing the decompressor and the CS descriptor
used ends up being the EFI one which is not mapped in the identity
page table, leading to early SEV/SNP guest communication exceptions
resulting in the guest crashing
* tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/head/64: Switch to KERNEL_CS as soon as new GDT is installed
Linus Torvalds [Sun, 11 Jun 2023 17:07:35 +0000 (10:07 -0700)]
Merge tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Five smb3 server fixes, all also for stable:
- Fix four slab out of bounds warnings: improve checks for protocol
id, and for small packet length, and for create context parsing,
and for negotiate context parsing
- Fix for incorrect dereferencing POSIX ACLs"
* tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: validate smb request protocol id
ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
ksmbd: fix out-of-bound read in parse_lease_state()
ksmbd: fix out-of-bound read in deassemble_neg_contexts()
Linus Torvalds [Sat, 10 Jun 2023 20:21:04 +0000 (13:21 -0700)]
Merge tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fixes from Vinod Koul:
"Core fix for missing flag clear, error patch handling in qcom driver
and BIOS quirk for HP Spectre x360:
- HP Spectre x360 soundwire DMI quirk
- Error path handling for qcom driver
- Core fix for missing clear of alloc_slave_rt"
* tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: Add missing clear of alloc_slave_rt
soundwire: qcom: add proper error paths in qcom_swrm_startup()
soundwire: dmi-quirks: add new mapping for HP Spectre x360
Linus Torvalds [Sat, 10 Jun 2023 20:01:09 +0000 (13:01 -0700)]
Merge tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes this time are for the Qualcomm Snapdragon
platforms.
There are bug fixes for error handling in Qualcomm icc-bwmon,
rpmh-rsc, ramp_controller and rmtfs driver as well as the AMD tee
firmware driver and a missing initialization in the Arm ff-a firmware
driver. The Qualcomm RPMh and EDAC drivers need some rework to work
correctly on all supported chips.
The DT fixes include:
- i.MX8 fixes for gpio, pinmux and clock settings
- ADS touchscreen gpio polarity settings in several machines
- Address dtb warnings for caches, panel and input-enable properties
on Qualcomm platforms
- Incorrect data on qualcomm platforms fir SA8155P power domains,
SM8550 LLCC, SC7180-lite SDRAM frequencies and SM8550 soundwire
- Remoteproc firmware paths are corrected for Sony Xperia 10 IV"
* tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
firmware: arm_ffa: Set handle field to zero in memory descriptor
ARM: dts: Fix erroneous ADS touchscreen polarities
arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
EDAC/qcom: Get rid of hardcoded register offsets
EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup()
arm64: dts: qcom: sm8550: Use the correct LLCC register scheme
dt-bindings: cache: qcom,llcc: Fix SM8550 description
arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards
arm64: dts: qcom: sm8550: use uint16 for Soundwire interval
soc: qcom: rpmhpd: Add SA8155P power domains
arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains
dt-bindings: power: qcom,rpmpd: Add SA8155P
soc: qcom: Rename ice to qcom_ice to avoid module name conflict
soc: qcom: rmtfs: Fix error code in probe()
soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe()
ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
ARM: at91: pm: fix imbalanced reference counter for ethernet devices
arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths
...
Linus Torvalds [Fri, 9 Jun 2023 21:21:20 +0000 (14:21 -0700)]
Merge tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix an issue with the hardware queue nr_active, causing it to become
imbalanced (Tian)
- Fix an issue with null_blk not releasing pages if configured as
memory backed (Nitesh)
- Fix a locking issue in dasd (Jan)
* tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux:
s390/dasd: Use correct lock while counting channel queue length
null_blk: Fix: memory release when memory_backed=1
blk-mq: fix blk_mq_hw_ctx active request accounting
Linus Torvalds [Fri, 9 Jun 2023 18:04:08 +0000 (11:04 -0700)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio bug fixes from Michael Tsirkin:
"A bunch of fixes all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: use canonical ftrace path
vhost_vdpa: support PACKED when setting-getting vring_base
vhost: support PACKED when setting-getting vring_base
vhost: Fix worker hangs due to missed wake up calls
vhost: Fix crash during early vhost_transport_send_pkt calls
vhost_net: revert upend_idx only on retriable error
vhost_vdpa: tell vqs about the negotiated
vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister
tools/virtio: Add .gitignore for ringtest
tools/virtio: Fix arm64 ringtest compilation error
vduse: avoid empty string for dev name
vhost: use kzalloc() instead of kmalloc() followed by memset()
Linus Torvalds [Fri, 9 Jun 2023 17:53:58 +0000 (10:53 -0700)]
Merge tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix for a potential data corruption in differential backup and
snapshot-based mirroring scenarios in RBD and a reference counting
fixup to avoid use-after-free in CephFS, all marked for stable"
* tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client:
ceph: fix use-after-free bug for inodes when flushing capsnaps
rbd: get snapshot context after exclusive lock is ensured to be held
rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting
Jan Höppner [Fri, 9 Jun 2023 15:37:50 +0000 (17:37 +0200)]
s390/dasd: Use correct lock while counting channel queue length
The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit 583d6535cb9d ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.
The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.
Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.
Fixes: 583d6535cb9d ("dasd: remove dead code") Cc: stable@vger.kernel.org # v5.0+ Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 9 Jun 2023 16:36:17 +0000 (09:36 -0700)]
Merge tag 'riscv-for-linus-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to avoid ISA-disallowed privilege mappings that can result from
WRITE+EXEC mmap requests from userspace.
- A fix for kfence to handle the huge pages.
- A fix to avoid converting misaligned VAs to huge pages.
- ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE has been selected so kprobe
can understand user pointers.
* tag 'riscv-for-linus-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix kprobe __user string arg print fault issue
riscv: Check the virtual alignment before choosing a map size
riscv: Fix kfence now that the linear mapping can be backed by PUD/P4D/PGD
riscv: mm: Ensure prot of VM_WRITE and VM_EXEC must be readable
Linus Torvalds [Fri, 9 Jun 2023 16:29:51 +0000 (09:29 -0700)]
Merge tag 's390-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Avoid linker error for randomly generated config file that has
CONFIG_BRANCH_PROFILE_NONE enabled and make it similar to riscv, x86
and also to commit 4bf3ec384edf ("s390: disable branch profiling for
vdso").
- Currently, if the device is offline and all the channel paths are
either configured or varied offline, the associated subchannel gets
unregistered. Don't unregister the subchannel, instead unregister
offline device.
* tag 's390-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/purgatory: disable branch profiling
s390/cio: unregister device when the only path is gone
Linus Torvalds [Fri, 9 Jun 2023 16:17:25 +0000 (09:17 -0700)]
Merge tag 'gpio-fixes-for-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"Two fixes for the GPIO testing module and one commit making Andy a
reviewer for the GPIO subsystem:
- fix a memory corruption bug in gpio-sim
- fix inconsistencies in user-space configuration of gpio-sim
- make Andy Shevchenko a reviewer for the GPIO subsystem"
* tag 'gpio-fixes-for-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
MAINTAINERS: add Andy Shevchenko as reviewer for the GPIO subsystem
gpio: sim: quietly ignore configured lines outside the bank
gpio: sim: fix memory corruption when adding named lines and unnamed hogs
Ross Zwisler [Wed, 15 Feb 2023 22:33:49 +0000 (15:33 -0700)]
tools/virtio: use canonical ftrace path
The canonical location for the tracefs filesystem is at /sys/kernel/tracing.
But, from Documentation/trace/ftrace.rst:
Before 4.1, all ftrace tracing control files were within the debugfs
file system, which is typically located at /sys/kernel/debug/tracing.
For backward compatibility, when mounting the debugfs file system,
the tracefs file system will be automatically mounted at:
/sys/kernel/debug/tracing
A few spots in tools/virtio still refer to this older debugfs
path, so let's update them to avoid confusion.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Message-Id: <20230215223350.2658616-6-zwisler@google.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Shannon Nelson [Mon, 24 Apr 2023 22:50:31 +0000 (15:50 -0700)]
vhost_vdpa: support PACKED when setting-getting vring_base
Use the right structs for PACKED or split vqs when setting and
getting the vring base.
Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend") Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-4-shannon.nelson@amd.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Shannon Nelson [Mon, 24 Apr 2023 22:50:30 +0000 (15:50 -0700)]
vhost: support PACKED when setting-getting vring_base
Use the right structs for PACKED or split vqs when setting and
getting the vring base.
Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend") Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-3-shannon.nelson@amd.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Linus Torvalds [Fri, 9 Jun 2023 15:38:22 +0000 (08:38 -0700)]
Merge tag 'sound-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Lots of small fixes, and almost all are device-specific.
A few of them are the fixes for the old regressions by the fast kctl
lookups (introduced around 5.19). Others are ASoC simple-card fixes,
selftest compile warning fixes, ASoC AMD quirks, various ASoC codec
fixes as well as usual HD-audio quirks"
* tag 'sound-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: hda/realtek: Enable 4 amplifiers instead of 2 on a HP platform
ALSA: hda: Fix kctl->id initialization
ALSA: gus: Fix kctl->id initialization
ALSA: cmipci: Fix kctl->id initialization
ALSA: ymfpci: Fix kctl->id initialization
ALSA: ice1712,ice1724: fix the kcontrol->id initialization
ALSA: hda/realtek: Add quirk for Clevo NS50AU
ALSA: hda/realtek: Add quirks for Asus ROG 2024 laptops using CS35L41
ALSA: hda/realtek: Add "Intel Reference board" and "NUC 13" SSID in the ALC256
ALSA: hda/realtek: Add Lenovo P3 Tower platform
ALSA: hda/realtek: Add a quirk for HP Slim Desktop S01
selftests: alsa: pcm-test: Fix compiler warnings about the format
ASoC: fsl_sai: Enable BCI bit if SAI works on synchronous mode with BYP asserted
ASoC: simple-card-utils: fix PCM constraint error check
ASoC: cs35l56: Remove NULL check from cs35l56_sdw_dai_set_stream()
ASoC: max98363: limit the number of channel to 1
ASoC: max98363: Removed 32bit support
ASoC: mediatek: mt8195: fix use-after-free in driver remove path
ASoC: mediatek: mt8188: fix use-after-free in driver remove path
ASoC: amd: yc: Add Thinkpad Neo14 to quirks list for acp6x
...
Linus Torvalds [Fri, 9 Jun 2023 15:23:01 +0000 (08:23 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fix from Ted Ts'o:
"Fix an ext4 regression which breaks remounting r/w file systems that
have the quota feature enabled"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: only check dquot_initialize_needed() when debugging
Revert "ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled"
Arnd Bergmann [Fri, 9 Jun 2023 12:15:18 +0000 (14:15 +0200)]
Merge tag 'imx-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.4, round 2:
- Fix SPI CS pinmux for the final production version of imx8mn-beacon
board.
- Fix GPIOs for USDHC2 CD and WP signals on imx8qm-mek board.
- Assign default clock rate for i.MX8 LPUARTs to fix UART failure.
* tag 'imx-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
Linus Torvalds [Fri, 9 Jun 2023 02:14:10 +0000 (19:14 -0700)]
Merge tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Bit busier and a bit more scattered than usual. amdgpu is the main
one, with ivpu and msm having a few fixes, then i915, exynos, ast,
lima, radeon with some misc bits, but overall nothing standing out.
fb-helper:
- Fill in fb-helper vars more correctly
i915:
- CDCLK voltage fix for ADL-P
- eDP wake sync pulse fix
- Two error handling fixes to selftests
exynos:
- Fix wrong return in Exynos vidi driver
- Fix use-after-free issue to Exynos g2d driver
ast:
- resume and modeset fixes for ast
ivpu:
- Assorted ivpu fixes
lima:
- lima context destroy fix
msm:
- Fix max segment size to address splat on newer a6xx
- Disable PSR by default w/ modparam to re-enable, since there still
seems to be a lingering issue
- Fix HPD issue
- Fix issue with unitialized GMU mutex"
* tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drm: (32 commits)
drm/msm/a6xx: initialize GMU mutex earlier
drm/msm/dp: enable HDP plugin/unplugged interrupts at hpd_enable/disable
accel/ivpu: Fix sporadic VPU boot failure
accel/ivpu: Do not use mutex_lock_interruptible
accel/ivpu: Do not trigger extra VPU reset if the VPU is idle
drm/amd/display: Reduce sdp bw after urgent to 90%
drm/amdgpu: change reserved vram info print
drm/amdgpu: fix xclk freq on CHIP_STONEY
drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl
Revert "drm/amdgpu: switch to golden tsc registers for raven/raven2"
Revert "drm/amdgpu: Differentiate between Raven2 and Raven/Picasso according to revision id"
Revert "drm/amdgpu: change the reference clock for raven/raven2"
drm/amd/display: add ODM case when looking for first split pipe
drm/amd: Make lack of `ACPI_FADT_LOW_POWER_S0` or `CONFIG_AMD_PMC` louder during suspend path
drm/amd/pm: conditionally disable pcie lane switching for some sienna_cichlid SKUs
drm/amd/pm: Fix power context allocation in SMU13
drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram
drm/amd: Disallow s0ix without BIOS support again
drm/i915/selftests: Add some missing error propagation
drm/exynos: fix race condition UAF in exynos_g2d_exec_ioctl
...
Linus Torvalds [Fri, 9 Jun 2023 01:52:54 +0000 (18:52 -0700)]
Merge tag 'cgroup-for-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- Fix css_set reference leaks on fork failures
- Fix CPU hotplug locking in cgroup_transfer_tasks() which is used by
cgroup1 cpuset
- Doc update
* tag 'cgroup-for-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Documentation: Clarify usage of memory limits
cgroup: always put cset in cgroup_css_set_put_fork
cgroup: fix missing cpus_read_{lock,unlock}() in cgroup_transfer_tasks()
Dave Airlie [Fri, 9 Jun 2023 01:20:22 +0000 (11:20 +1000)]
Merge tag 'drm-msm-fixes-2023-06-08' of https://gitlab.freedesktop.org/drm/msm into drm-fixes
A few more late fixes for v6.4-rc6
+ Fix max segment size to address splat on newer a6xx
+ Disable PSR by default w/ modparam to re-enable, since there
still seems to be a lingering issue
+ Fix HPD issue
+ Fix issue with unitialized GMU mutex
Move GMU mutex initialization earlier to make sure that it is always
initialized. a6xx_destroy can be called from ther failure path before
GMU initialization.
Fixes: 4cd15a3e8b36 ("drm/msm/a6xx: Make GPU destroy a bit safer") Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/531540/ Signed-off-by: Rob Clark <robdclark@chromium.org>
Kuogee Hsieh [Tue, 23 May 2023 21:52:36 +0000 (14:52 -0700)]
drm/msm/dp: enable HDP plugin/unplugged interrupts at hpd_enable/disable
The internal_hpd flag is set to true by dp_bridge_hpd_enable() and set to
false by dp_bridge_hpd_disable() to handle GPIO pinmuxed into DP controller
case. HDP related interrupts can not be enabled until internal_hpd is set
to true. At current implementation dp_display_config_hpd() will initialize
DP host controller first followed by enabling HDP related interrupts if
internal_hpd was true at that time. Enable HDP related interrupts depends on
internal_hpd status may leave system with DP driver host is in running state
but without HDP related interrupts being enabled. This will prevent external
display from being detected. Eliminated this dependency by moving HDP related
interrupts enable/disable be done at dp_bridge_hpd_enable/disable() directly
regardless of internal_hpd status.
Changes in V3:
-- dp_catalog_ctrl_hpd_enable() and dp_catalog_ctrl_hpd_disable()
-- rewording ocmmit text
Changes in V4:
-- replace dp_display_config_hpd() with dp_display_host_start()
-- move enable_irq() at dp_display_host_start();
Changes in V5:
-- replace dp_display_host_start() with dp_display_host_init()
Changes in V6:
-- squash remove enable_irq() and disable_irq()
Fixes: cd198caddea7 ("drm/msm/dp: Rely on hpd_enable/disable callbacks") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Tested-by: Leonard Lausen <leonard@lausen.nl> # on sc7180 lazor Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Tested-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Link: https://lore.kernel.org/r/1684878756-17830-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Dave Airlie [Fri, 9 Jun 2023 01:10:09 +0000 (11:10 +1000)]
Merge tag 'drm-misc-fixes-2023-06-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v6.4-rc6:
- resume and modeset fixes for ast.
- Fill in fb-helper vars more correctly.
- Assorted ivpu fixes.
- lima context destroy fix.
Linus Torvalds [Thu, 8 Jun 2023 20:54:26 +0000 (13:54 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Two tiny arm64 fixes for -rc6.
One fixes a build breakage when MAX_ORDER can be nonsensical if
CONFIG_EXPERT=y and the other fixes the address masking for perf's
page fault software events so that it is consistent amongst them:
- Fix build breakage due to bogus MAX_ORDER definitions on !4k pages
- Avoid masking fault address for perf software events"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: pass original fault address to handle_mm_fault() in PER_VMA_LOCK block
arm64: Remove the ARCH_FORCE_MAX_ORDER config input prompt
Mike Christie [Wed, 7 Jun 2023 19:23:38 +0000 (14:23 -0500)]
vhost: Fix worker hangs due to missed wake up calls
We can race where we have added work to the work_list, but
vhost_task_fn has passed that check but not yet set us into
TASK_INTERRUPTIBLE. wake_up_process will see us in TASK_RUNNING and
just return.
This bug was intoduced in commit f9010dbdce91 ("fork, vhost: Use
CLONE_THREAD to fix freezer/ps regression") when I moved the setting
of TASK_INTERRUPTIBLE to simplfy the code and avoid get_signal from
logging warnings about being in the wrong state. This moves the setting
of TASK_INTERRUPTIBLE back to before we test if we need to stop the
task to avoid a possible race there as well. We then have vhost_worker
set TASK_RUNNING if it finds work similar to before.
Fixes: f9010dbdce91 ("fork, vhost: Use CLONE_THREAD to fix freezer/ps regression") Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20230607192338.6041-3-michael.christie@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mike Christie [Wed, 7 Jun 2023 19:23:37 +0000 (14:23 -0500)]
vhost: Fix crash during early vhost_transport_send_pkt calls
If userspace does VHOST_VSOCK_SET_GUEST_CID before VHOST_SET_OWNER we
can race where:
1. thread0 calls vhost_transport_send_pkt -> vhost_work_queue
2. thread1 does VHOST_SET_OWNER which calls vhost_worker_create.
3. vhost_worker_create will set the dev->worker pointer before setting
the worker->vtsk pointer.
4. thread0's vhost_work_queue will see the dev->worker pointer is
set and try to call vhost_task_wake using not yet set worker->vtsk
pointer.
5. We then crash since vtsk is NULL.
Before commit 6e890c5d5021 ("vhost: use vhost_tasks for worker
threads"), we only had the worker pointer so we could just check it to
see if VHOST_SET_OWNER has been done. After that commit we have the
vhost_worker and vhost_task pointer, so we can now hit the bug above.
This patch embeds the vhost_worker in the vhost_dev and moves the work
list initialization back to vhost_dev_init, so we can just check the
worker.vtsk pointer to check if VHOST_SET_OWNER has been done like
before.
Fixes: 6e890c5d5021 ("vhost: use vhost_tasks for worker threads") Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20230607192338.6041-2-michael.christie@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reported-by: syzbot+d0d442c22fa8db45ff0e@syzkaller.appspotmail.com Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
vhost_net: revert upend_idx only on retriable error
Fix possible virtqueue used buffers leak and corresponding stuck
in case of temporary -EIO from sendmsg() which is produced by
tun driver while backend device is not up.
In case of no-retriable error and zcopy do not revert upend_idx
to pass packet data (that is update used_idx in corresponding
vhost_zerocopy_signal_used()) as if packet data has been
transferred successfully.
v2: set vq->heads[ubuf->desc].len equal to VHOST_DMA_DONE_LEN
in case of fake successful transmit.
Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru>
Message-Id: <20230424204411.24888-1-asmetanin@yandex-team.ru> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru> Acked-by: Jason Wang <jasowang@redhat.com>
Shannon Nelson [Mon, 24 Apr 2023 22:50:29 +0000 (15:50 -0700)]
vhost_vdpa: tell vqs about the negotiated
As is done in the net, iscsi, and vsock vhost support, let the vdpa vqs
know about the features that have been negotiated. This allows vhost
to more safely make decisions based on the features, such as when using
PACKED vs split queues.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230424225031.18947-2-shannon.nelson@amd.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Dragos Tatulea [Tue, 16 May 2023 09:58:01 +0000 (12:58 +0300)]
vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister
Currently the vdpa device is unregistered after the workqueue that
processes vq commands is disabled. However, the device unregister
process can still send commands to the cvq (a vlan delete for example)
which leads to a hang because the handing workqueue has been disabled
and the command never finishes:
The fix is to disable and destroy the workqueue after the device
unregister. It is expected that vhost will not trigger kicks after
the unregister. But even if it would, the wq is disabled already by
setting the pointer to NULL (done so in the referenced commit).
Fixes: ad6dc1daaf29 ("vdpa/mlx5: Avoid processing works if workqueue was destroyed") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20230516095800.3549932-1-dtatulea@nvidia.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Acked-by: Jason Wang <jasowang@redhat.com>
Rong Tao [Thu, 25 May 2023 08:37:28 +0000 (16:37 +0800)]
tools/virtio: Add .gitignore for ringtest
Ignore executables for ringtest.
Signed-off-by: Rong Tao <rongtao@cestc.cn>
Message-Id: <tencent_C121802C93CB4095C6D7D95113442E830A07@qq.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add cpu_relax() for arm64 instead of directly assert(), and add assert.h
header file. Also, add smp_wmb and smp_mb for arm64.
Compilation error as follows, avoid __always_inline undefined.
$ make
cc -Wall -pthread -O2 -ggdb -flto -fwhole-program -c -o ring.o ring.c
In file included from ring.c:10:
main.h: In function ‘busy_wait’:
main.h:99:21: warning: implicit declaration of function ‘assert’
[-Wimplicit-function-declaration]
99 | #define cpu_relax() assert(0)
| ^~~~~~
main.h:107:17: note: in expansion of macro ‘cpu_relax’
107 | cpu_relax();
| ^~~~~~~~~
main.h:12:1: note: ‘assert’ is defined in header ‘<assert.h>’; did you
forget to ‘#include <assert.h>’?
11 | #include <stdbool.h>
+++ |+#include <assert.h>
12 |
main.h: At top level:
main.h:143:23: error: expected ‘;’ before ‘void’
143 | static __always_inline
| ^
| ;
144 | void __read_once_size(const volatile void *p, void *res, int
size)
| ~~~~
main.h:158:23: error: expected ‘;’ before ‘void’
158 | static __always_inline void __write_once_size(volatile void *p,
void *res, int size)
| ^~~~~
| ;
make: *** [<builtin>: ring.o] Error 1
Signed-off-by: Rong Tao <rongtao@cestc.cn>
Message-Id: <tencent_F53E159DD7925174445D830DA19FACF44B07@qq.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sheng Zhao [Tue, 30 May 2023 03:36:26 +0000 (11:36 +0800)]
vduse: avoid empty string for dev name
Syzkaller hits a kernel WARN when the first character of the dev name
provided is NULL. Solution is to add a NULL check before calling
cdev_device_add() in vduse_create_dev().
As riscv do not select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE,
the +0($arg2) addr is processed as a kernel address though it is a
userspace address, cause the above filename=(fault) print. So select
ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE to avoid the issue, after that the
kprobe trace is ok as below:
projects / thirdparty / linux.git / log
