Tom Rini [Wed, 28 May 2025 00:03:01 +0000 (18:03 -0600)]
include/dt-bindings/reset: Remove local version of bcm6318-reset.h
Aside from SPDX tags, the only difference between our version of this
header and upstream is that BCM6318_RST_HOSTMIPS was defined to 11 (the
same as BCM6318_RST_PHYMIPS) and is now defined to 12.
Tom Rini [Tue, 27 May 2025 23:50:38 +0000 (17:50 -0600)]
include/dt-bindings: Remove strict subset headers
As part of moving to using OF_UPSTREAM and so the upstream dt-bindings
headers we have a number of these headers that are in our include
directory and differ in being a strict subset of what is found upstream.
We can safely remove the copies under include/dt-bindings now to prevent
future conflicts.
As part of moving to using OF_UPSTREAM and so the upstream dt-bindings
headers we have a number of these headers that are in our include
directory and differ only in combinations of spacing changes and/or
switching to SPDX license tags. We can safely remove the copies under
include/dt-bindings now to prevent future conflicts.
Tom Rini [Tue, 27 May 2025 22:18:34 +0000 (16:18 -0600)]
include/dt-bindings: Remove identical headers
As part of moving to using OF_UPSTREAM and so the upstream dt-bindings
headers we have a number of these headers that are in our include
directory and are currently identical to the versions in dts/upstream.
We can remove these now to prevent future conflicts.
Tom Rini [Tue, 27 May 2025 22:18:33 +0000 (16:18 -0600)]
include/dt-bindings: Remove unused headers
As part of moving to using OF_UPSTREAM and so the upstream dt-bindings
headers we have a number of these headers that are in our include
directory and not referenced by any code outside of dts/upstream. We can
remove these now to prevent future conflicts.
Heiko Thiery [Wed, 28 May 2025 09:05:37 +0000 (11:05 +0200)]
arm: dts: remove k3-serdes.h
This file is a duplicate and also comes with the sync of the linux
mainline dts files. By removing this the one from the dts folder should
be taken that is more up-to-date.
cmd: bootmenu: permit to select bootmenu entry with a shortcut
Permit to select a bootmenu entry with a key shortcut. This is
especially useful in production or testing scenario to automate flashing
procedure or testing procedure.
The boot entry are changed to append the shortcut key to it.
Example:
1. Run default boot command.
2. Boot system via TFTP.
3. Boot production system from NAND.
4. Boot recovery system from NAND.
5. Load production system via TFTP then write to NAND.
6. Load recovery system via TFTP then write to NAND.
7. Load BL31+U-Boot FIP via TFTP then write to NAND.
8. Load BL2 preloader via TFTP then write to NAND.
9. Reboot.
a. Reset all settings to factory defaults.
0. Exit
0 is always reserved for Exit to console.
On pressing the keyboard key 2, the bootmenu entry 2 is selected and
executed.
Up to 34 key shortcut (0 excluded as reserved) are supported from 1-9
and a-z.
If a shortcut key not present in the bootmenu list is pressed, it is
simply ignored and eventually the autoboot is interrupted.
Capital A-Z are converted to lower a-z and the related option is
selected.
Suggested-by: Weijie Gao <weijie.gao@mediatek.com> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Tested-by: Petr Štetiar <ynezz@true.cz>
The high-speed UART from MediaTek supports baudrate accuracy
compensation when using high-speed mode 3.
This is done by calculating the first digit of the fraction part of
sample count value. The fraction value will be then used as the
reference to insert 0 to 10 sample cycle(s) to one frame (assume
that frame format is 8n1, i.e. 10 bits per frame).
The fracdiv_[l/m] registers are used to determine whether a bit in one frame
should be inserted with one sample cycle.
With typical 40MHz source clock, the actual baudrates with/without
accuracy compensation are:
Parth Pancholi [Mon, 19 May 2025 15:47:45 +0000 (16:47 +0100)]
board: toradex: add verdin am62p support
This adds initial support for the Toradex Verdin AM62P module.
The module consists of an TI AM62P family SoC, a TPS65219 PMIC, a
Gigabit Ethernet PHY, up to 8GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC,
an I2C EEPROM, an RX8130 RTC, plus an optional Bluetooth/Wi-Fi module.
These specific changes adds support for Toradex Verdin AM62P Quad 2GB WB
IT module.
implement a driver to use semtech pinctrl and
gpio expander, this driver is adapted from a
existent linux driver that is written by
Gregory Bean <gbean@codeaurora.org>.
Anton Moryakov [Fri, 16 May 2025 15:25:38 +0000 (18:25 +0300)]
tools: fix handle leak in ifdtool.c
Prevent file descriptor leaks by properly closing 'fd' and 'new_fd'
when fstat() or write() operations fail.
- Added close(fd) before return in open_for_read() if fstat() fails.
- Added close(new_fd) before return in write_image() if write() fails.
- No close needed if open() fails (fd == -1 is invalid).
Signed-off-by: Anton Moryakov <ant.v.moryakov@gmail.com> Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Tom Rini [Mon, 2 Jun 2025 23:43:56 +0000 (17:43 -0600)]
Merge patch series "Audit include list for include/[a-m]*.h"
Tom Rini <trini@konsulko.com> says:
Hey all,
Related to my other series I've posted recently on cleaning up some
headers, this series here is the result of at least lightly auditing the
#includes used in include/[a-m]*.h. This ignores subdirectories, as at
least in part I think the top-level includes we've constructed are the
most likely places to have some extra transitive include paths. I'm sure
there's exceptions and I'll likely audit deeper once this first pass is
done. This only gets as far as "include/m*.h" because I didn't want this
to get too big. This also sets aside <miiphy.h> and <phy.h>. While
miiphy.h does not directly need <phy.h> there are *so* many users and I
think I had half of the tree just about not building when I first tried.
It might be worth further investigation, but it might just be OK as-is.
Tom Rini [Wed, 21 May 2025 22:51:22 +0000 (16:51 -0600)]
global: Cleanup usage of "ETH_ALEN"
The value of "ETH_ALEN" is defined to 6 in <linux/if_ether.h>. This file
is included in <net.h>. In the places where we had ETH_ALEN but no
direct include of <net.h>, add <linux/if_ether.h>. In the places where
we had a custom name used, make use of ETH_ALEN instead.
Tom Rini [Wed, 21 May 2025 22:51:21 +0000 (16:51 -0600)]
include/mtd.h: Cleanup usage
There are only a few things found in <mtd.h> today. Go through and audit
the C files which include <mtd.h> and remove it when not required. Then,
add it to the files which had either missed it or had an indirect
inclusion of it.
Tom Rini [Wed, 21 May 2025 22:51:20 +0000 (16:51 -0600)]
include/mmc.h: Audit include list
This file does not need <linux/sizes.h> nor <linux/compiler.h> so remove
them. This exposes however that a number of other files had been relying
on this implicit include for <linux/sizes.h> so add that where needed.
Tom Rini [Wed, 21 May 2025 22:51:19 +0000 (16:51 -0600)]
include/ide.h: Cleanup usage
At this point in time, <ide.h> provides the IDE_BUS macro and the
function prototype for ide_set_reset, which is used with IDE_RESET. The
only files which should include this header are the ones that either use
that macro or that function. Remove <blk.h> from <ide.h> and remove
<ide.h> from places which do not need it.
Tom Rini [Wed, 21 May 2025 22:51:17 +0000 (16:51 -0600)]
include/efi_loader.h, include/efi_tcg2.h: Audit include list
In include/efi_loader.h we do not directly need <log.h>, <part_efi.h>,
<pe.h> nor <linux/oid_registry.h> so remove them. In include/efi_tcg2.h
we make use of <part_efi.h> but did not include it, so add it directly.
Tom Rini [Wed, 21 May 2025 22:51:08 +0000 (16:51 -0600)]
include/bios_emul.h: Audit include list
This file does not need <pc.h> but does directly need
<linux/types.h>. Furthermore, arch/x86/lib/bios.c was getting <pci.h>
via <bios_emul.h> so add it there.
Marek Vasut [Sun, 18 May 2025 16:02:58 +0000 (18:02 +0200)]
ARM: Align image end to 8 bytes to fit DT alignment
Align U-Boot image end to 8 bytes to make sure DT alignment requirement
is fulfilled. This fixes a possible failure in fdt_find_separate() in
case the U-Boot image is aligned to 4 Bytes and DT is appended at the
end at already 8 Byte aligned offset.
Link: https://source.denx.de/u-boot/u-boot/-/issues/30 Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Usb gadget:
dwc2: Fix incorrect ULPI_UTMI_SEL bit setting
dwc2: Fix HBstLen setting for external DMA mode
dwc2: Various refactors to get the code closer to Linux
dwc2: Support reset logic for v4.20a
Junhui Liu [Sun, 26 Jan 2025 08:29:59 +0000 (00:29 -0800)]
usb: dwc2: Refactor register operations with clrsetbits macros
Refactor DWC2 USB gadget driver to replace manual read-modify-write
operations with `clrsetbits_le32`, `setbits_le32`, and `clrbits_le32`
macros, which simplify the code and improve readability.
Kongyang Liu [Fri, 10 Jan 2025 13:55:27 +0000 (21:55 +0800)]
usb: dwc2: Replace uint<x>_t types with u<x>
Updates all instances of uint8_t, uint16_t, and uint32_t to u8, u16, and
u32 respectively, ensuring consistent use of kernel-preferred types and
resolving checkpatch.pl warnings.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-8-987f4fd6f8b2@pigmoral.tech Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Kongyang Liu [Fri, 10 Jan 2025 13:55:26 +0000 (21:55 +0800)]
usb: dwc2: Unify flush and reset logic with v4.20a support
This patch merges flush and reset logic for both host and gadget code
into a common set of functions, reducing duplication. It also adds support
for the updated reset logic to compatible with core version since v4.20a.
Kongyang Liu [Fri, 10 Jan 2025 13:55:25 +0000 (21:55 +0800)]
usb: dwc2: Extract macro definitions to common header
Some macros are shared between host and gadget code, causing duplicated
definitions. Move DWC2 macro definitions from host and gadget code into a
common header to reduce duplication.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-6-987f4fd6f8b2@pigmoral.tech Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Kongyang Liu [Fri, 10 Jan 2025 13:55:24 +0000 (21:55 +0800)]
usb: dwc2: Align macros with Linux kernel definitions
Update the DWC2 macros to match those used in the Linux kernel, making
it easier to synchronize updates with kernel. Also removed some unused
macros to cleanup the code.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech> Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-5-987f4fd6f8b2@pigmoral.tech Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Kongyang Liu [Fri, 10 Jan 2025 13:55:23 +0000 (21:55 +0800)]
usb: dwc2: Clean up with bitfield macros
Use FIELD_PREP, FIELD_GET, BIT, and GENMASK macros to standardize bit
manipulation across the DWC2 code, improving readability and
maintainability without altering functionality.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech> Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-4-987f4fd6f8b2@pigmoral.tech Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Kongyang Liu [Fri, 10 Jan 2025 13:55:22 +0000 (21:55 +0800)]
usb: dwc2: Fix HBstLen setting for external DMA mode
The loop used to calculate HBstLen for extern DMA mode does not produce
the correct result according to the datasheet [1]. Replacing that loop
with a direct calculation using LOG2 to correctly assign the burst length
in the GAHBCFG register for external DMA mode.
Junhui Liu [Fri, 10 Jan 2025 13:55:21 +0000 (21:55 +0800)]
usb: dwc2: Fix incorrect ULPI_UTMI_SEL bit setting
The ULPI_UTMI_SEL bit in the DWC2 driver was set incorrectly. According
to the datasheet [1], this bit should be set to 0 for UTMI interface and 1
for ULPI interface. The existing code had this logic reversed,
causing the interface selection to be incorrect.
This commit corrects the ULPI_UTMI_SEL bit setting to match the
datasheet's description. Referencing the kernel's code [2] also confirms
this fix.
Kongyang Liu [Fri, 10 Jan 2025 13:55:20 +0000 (21:55 +0800)]
usb: dwc2: Extract register definitions to common header file
The same registers are accessed in both the otg and gatet drivers of
dwc2, and these registers are repeatedly defined in these two parts.
Extract register definitions into a common header file to reduce
redundancy and make the code more maintainable.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech> Link: https://lore.kernel.org/r/20250110-dwc2-dev-v4-1-987f4fd6f8b2@pigmoral.tech Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Introduce the BSH SystemMaster (SMM) M2B board. Notably, the M2B is
designed to leverage the existing device tree of its predecessor, the M2.
The primary distinction arises from memory incompatibilities with the M2.
To address this, we've implemented a configuration system that allows for
selective inclusion of the desired memory components.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Add i.MX6UL clk driver for i.MX6UL CLK driver model usage
Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Tim Harvey [Fri, 23 May 2025 17:20:15 +0000 (10:20 -0700)]
board: venice: add FSA support
The Gateworks Flexible Socket Adapters adapt common
busses such as SDIO/UART/USB/PCI to various connectors
such as M.2 B-Key, M.2 E-Key, M.2 M-Key, and MiniPCIe.
Each FSA has an EEPROM onboard describing its details as well as an
optional port-expander for configurable GPIO's.
Add support for identifying the FSA's and configuring their
details such as user description and GPIO's:
- enable pca953x, pca954x and eeprom support for communicating
with the I2C eeprom and gpio port expander on the FSA
- add FSA detection support
- add FSA gpio configuration support
Each FSA is identified in the device-tree by an alias to it's I2C
bus where an eeprom@54 node must exist as well as an gpio@20 node
for an io-expander. These nodes must be enabled so that
they can be probed to determine if they are actually present in
the system. If not present or not enabled the gpio expander can
not be used. This also requires livetree as the gpio expander
node if not present must be disabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tim Harvey [Fri, 23 May 2025 17:20:14 +0000 (10:20 -0700)]
board: venice: add imx8mp-gw82xx support
The Gateworks GW82XX-2X is an ARM based single board computer (SBC)
comprised of the i.MX8M Plus based gw702x SoM and the gw82xx
baseboard featuring:
- i.MX8M Plus SoC
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller (GSC)
- microSD (1.8V/3.3V Capable)
- panel status bi-color LED
- pushbutton switch
- fan controller with tachometer
- USB Type-C connector
- PCIe switch
- 2x GbE RJ45 connectors
- multi-protocol RS232/RS485/RS422 Serial ports
- 2x Flexible Socket Adapters with SDIO/UART/USB/PCIe
(for M.2 and miniPCIe expansion)
- 2x isolated CAN
- GPS
- accelerometer
- magnetometer
- off-board connectors for: SPI, GPIO, I2C, ADC
- Wide range DC power input
- support for 802.3at PoE (via adapter)
Add support for it by providing its device-tree.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tim Harvey [Fri, 23 May 2025 17:20:13 +0000 (10:20 -0700)]
board: venice: flip logic for GSC supervisor enable
Flip the logic used to determine if a board has the proper hardware to
support enabling the GSC voltage supervisor so that we do not need to
keep adding new models to the list.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tim Harvey [Fri, 23 May 2025 17:20:10 +0000 (10:20 -0700)]
board: venice: fix dram size for GW7901-SP486
The GW7901-SP486 with the exception of the -C revision has 2GB DRAM
loaded but incorrectly specifies 1GB in the EEPROM. Adjust the DRAM size
to account for this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tim Harvey [Fri, 23 May 2025 17:20:09 +0000 (10:20 -0700)]
board: venice: fix dram bus config for GW7902/GW7903/GW7904
The GW7902/GW7903/GW7904 have an alternate databus layout affecting a few
of the DDRC and DDR PHY registers.
The 512MB configuration used this alternate bus layout. Change
the 512MB config to the standard bus configuration and add a generic
function to patch the DDRC/PHY configs for the alternate bus layout.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tom Rini [Fri, 30 May 2025 19:53:50 +0000 (13:53 -0600)]
Merge tag 'dm-pull-30may25' of git://git.denx.de/u-boot-dm into next
Bring in recent expo enhancements:
- multi-line text
- highlighting of menu items
- rationalisation of menu and expo code
- support for object alignment
- editable strings
- various bug fixes and tweaks
This also includes some required abuf improvements.
Tom Rini [Fri, 30 May 2025 16:26:33 +0000 (10:26 -0600)]
Merge patch series "test/py: enable HTTP testing"
Adriano Cordova <adrianox@gmail.com> says:
Enable HTTP server in CI to support HTTP tests in pytest
QEMU does not emulate an HTTP server, unlike other services like DHCP or TFTP.
To enable HTTP tests during CI runs, start a simple Python HTTP server
on port 80. This allows tests that require HTTP access to run.
The HTTP server is launched on the host. For QEMU environments launched
with '-netdev,user' this means that the HTTP server runs together with DHCP
at 10.0.2.2. HTTP testing needs to be explicitly enabled with
env__efi_helloworld_net_http_test_skip = False.
We also default `WGET=y` in `ARCH_QEMU` configurations so that these HTTP
tests are included automatically when using QEMU in CI.
Marek Vasut [Mon, 12 May 2025 15:58:39 +0000 (17:58 +0200)]
image: Fix FIT image loadable section custom processing
The original commit always generated linker list entries with the same
entry variable name, because _function passed to ll_entry_declare() is
not a variable and therefore was interpreted as fixed string. Change it
to _type which is a variable and which does allow generation of multiple
unique linker list entries, one for each U_BOOT_FIT_LOADABLE_HANDLER().
Fixes: d7be50921ed3 ("image: Add FIT image loadable section custom processing") Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Tom Rini [Tue, 6 May 2025 14:04:12 +0000 (08:04 -0600)]
Gitlab: Rework sjg-lab calling test.py to be closer to test.py stage
There are a few differences between how the test.py stage invokes
test.py and how the sjg-lab stage invokes test.py. As a start of making
both the code and the output and artifacts similar, this updates the
sjg-lab stage with the following:
- Pass "-ra" so that we get the summary information in the job
- Make use of TEST_PY_EXTRA for passing "--capture=tee-sys"
- Re-order some of the arguments to be the same order when possible.
And most importantly:
- Create and save as an artifact the junitxml output.
The last part here is the kind of test result information that in the
future we should determine how to archive for future reference.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 30 May 2025 16:17:40 +0000 (10:17 -0600)]
Merge patch series "Almost complete DM_SERIAL migration"
Tom Rini <trini@konsulko.com> says:
In a private thread, Simon asked about what's needed to get PowerPC
migrated to DM_SERIAL. I went and took a look, and to complete the
entire DM_SERIAL migration (excluding SPL/TPL) we're actually nearly
there. This series first migrates PowerPC (and some NXP Layerscape
boards that share history more clearly with PowerPC parts), with the
biggest change being to make sure we still use the correct legacy
drivers in SPL/TPL (where SPL is extremely constrained). With that out
of the way, I looked at what was left. With two exceptions, it's
platforms which can be trivially enabled for conversion, and so we do
that.
Tom Rini [Fri, 2 May 2025 20:07:40 +0000 (14:07 -0600)]
global: Convert almost all remaining non-DM_SERIAL users
This converts almost all of the remaining non-DM_SERIAL users to enable
DM_SERIAL. These are platforms where there have long been other SoC
boards that have switched and so it's been a matter of inertia keeping
these from being converted. Do so now.
Tom Rini [Fri, 2 May 2025 20:07:39 +0000 (14:07 -0600)]
PowerPC / Layerscape: Finish migration to DM_SERIAL
Migrate the few ARM Layerscape platforms that had not been switched
along with all remaining PowerPC platforms to DM_SERIAL. For PowerPC,
this means that platforms which use SPL/TPL, keeping the non-DM serial
driver enabled there as they do not use DM. We also rework the guards
on how to define CFG_SYS_NS16550_CLK so that this is mostly in one place
now.
Simon Glass [Fri, 2 May 2025 14:46:58 +0000 (08:46 -0600)]
expo: Drop the special theme code for bootflow_menu
The expo now has all that is needed to apply a suitable theme, so drop
this unnecessary code. Any further tweaks can be added to the generic
expo code.
Simon Glass [Fri, 2 May 2025 14:46:57 +0000 (08:46 -0600)]
expo: Set up menu fully in bootflow_menu_start()
Apply the theme, calculate dimensions, highlight the menu and arrange
the scene correctly, so that everything is ready to go when the expo
is rendered.
Simon Glass [Fri, 2 May 2025 14:46:55 +0000 (08:46 -0600)]
expo: Update bootflow_menu_poll() to return a sequence ID
Rather than returning a bootflow, return the index of the bootflow. This
will allow callers to do their own translation to bootflows or some
other data structure.
Also return a special code when the user tries to move the pointer, so
that the caller can cancel the boot-menu timeout, if this is in use.
Simon Glass [Fri, 2 May 2025 14:46:52 +0000 (08:46 -0600)]
expo: Drop the render from expo_poll()
Within tests it is useful to be able to control rendering of the expo.
Drop the automatic call to expo_render() within expo_poll() and adjust
its callers to handle this instead.
Simon Glass [Fri, 2 May 2025 14:46:50 +0000 (08:46 -0600)]
expo: Support highlighting menu items
Expo normally uses a pointer to show the current item. Add support for
highlighting as well, since this makes it easier for the user to see the
current item.
Simon Glass [Fri, 2 May 2025 14:46:49 +0000 (08:46 -0600)]
expo: Add forward declarations to scene_internal.h
Provide some forward declarations for types used in this file, to keep
the LSP happy and avoid errors if the caller happens not to include the
required header.
Simon Glass [Fri, 2 May 2025 14:46:45 +0000 (08:46 -0600)]
expo: Support object alignment
Add support for left, right and centred alignment for text, in the
horizontal dimension.
Also support top, bottom and centred in the vertical dimension, for the
text object as a whole.
Alignment is not yet implemented for images. It has no meaning for
menus. A textline object uses a text object internally, so alignment
is supported there.
Provide some documentation to explain how objects are positioned.
Simon Glass [Fri, 2 May 2025 14:46:42 +0000 (08:46 -0600)]
expo: Support rendering multiple lines of text
Use the measurement info to write each line of text separately, thus
respecting word-wrapping and newlines.
Fix up the comment for scene_obj_render() while we are here.
Since a lineedit does not support alignment, add a special case to just
display the text if there is no measurement. This happens assuming the
lineedit is initially empty.
Simon Glass [Fri, 2 May 2025 14:46:40 +0000 (08:46 -0600)]
expo: Allow strings to be editable
In some cases dynamic text is needed, e.g. for a menu countdown. Add a
function which handles this, allowing the caller to take control of the
text that is shown on each render.
projects / thirdparty / u-boot.git / log
