The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices") Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices") Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.
In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.
Fixes: 9838b20a7fb2 ("net: sched: take rtnl lock in tc_setup_flow_action()") Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The above issue is due to previous incorrect implementation of
tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule()
to get struct flow_rule *rule which is no longer valid for tc filter
delete operation.
So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for
earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(),
this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload
record for 'RX frame steering' tc flower, currently used for VLAN
priority. The implementation has taken consideration for future extension
to include other type RX frame steering such as EtherType based.
v2:
- Clean up overly extensive backtrace and rewrite git message to better
explain the kernel NULL pointer issue.
Fixes: 0e039f5cf86c ("net: stmmac: add RX frame steering based on VLAN priority in tc flower") Tested-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should be doing the HE capabilities lookup based on the full
interface type so if P2P doesn't have HE but client has it doesn't
get confused. Fix that.
The function cfg80211_reg_can_beacon_relax() expects wiphy
mutex to be held when it is being called. However, when
reg_leave_invalid_chans() is called the mutex is not held.
Fix it by acquiring the lock before calling the function.
When we call ieee80211_agg_start_txq(), that will in turn call
schedule_and_wake_txq(). Called from ieee80211_stop_tx_ba_cb()
this is done under sta->lock, which leads to certain circular
lock dependencies, as reported by Chris Murphy:
https://lore.kernel.org/r/CAJCQCtSXJ5qA4bqSPY=oLRMbv-irihVvP7A2uGutEbXQVkoNaw@mail.gmail.com
In general, ieee80211_agg_start_txq() is usually not called
with sta->lock held, only in this one place. But it's always
called with sta->ampdu_mlme.mtx held, and that's therefore
clearly sufficient.
Change ieee80211_stop_tx_ba_cb() to also call it without the
sta->lock held, by factoring it out of ieee80211_remove_tid_tx()
(which is only called in this one place).
This breaks the locking chain and makes it less likely that
we'll have similar locking chain problems in the future.
Fixes: ba8c3d6f16a1 ("mac80211: add an intermediate software queue implementation") Reported-by: Chris Murphy <lists@colorremedies.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20211202152554.f519884c8784.I555fef8e67d93fff3d9a304886c4a9f8b322e591@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when deleting an endpoint the netlink PM treverses
all the local MPTCP sockets, regardless of their status.
If an MPTCP listener socket is bound to the IP matching the
delete endpoint, the listener TCP socket will be closed.
That is unexpected, the PM should only affect data subflows.
Additionally, syzbot was able to trigger a NULL ptr dereference
due to the above:
The recent GRE selftests defined NUM_NETIFS=10. If the users copy
forwarding.config.sample to forwarding.config directly, they will get
error "Command line is not complete" when run the GRE tests, because
create_netif_veth() failed with no interface name defined.
Fix it by extending the NETIFS with p9 and p10.
Fixes: 2800f2485417 ("selftests: forwarding: Test multipath hashing on inner IP pkts for GRE tunnel") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings
in mac_config") removed forcing of speed and duplex from
mv88e6xxx_mac_config(), where the link is forced down, and left it only
in mv88e6xxx_mac_link_up(), by which time link is unforced.
It seems that (at least on 88E6190) when changing cmode to 2500base-x,
if the link is not forced down, but the speed or duplex are still
forced, the forcing of new settings for speed & duplex doesn't take in
mv88e6xxx_mac_link_up().
Fix this by unforcing speed & duplex in mv88e6xxx_mac_link_down().
Fixes: 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings in mac_config") Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tiny fix. Option -u ("use udp") does not take an argument.
It can cause the next argument to silently be ignored.
Fixes: 5ebfb4cc3048 ("selftests/net: toeplitz test") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
we can remove 'q->classes[i].alist' only if DRR class 'i' was part of the
active list. In the ETS scheduler DRR classes belong to that list only if
the queue length is greater than zero: we need to test for non-zero value
of 'q->classes[i].qdisc->q.qlen' before removing from the list, similarly
to what has been done elsewhere in the ETS code.
Fixes: de6d25924c2a ("net/sched: sch_ets: don't peek at classes beyond 'nbands'") Reported-by: Shuang Li <shuali@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ming reported that with the abort path of the descriptor submission, there
can be a window where a completed descriptor can be missed to be completed
by the irq completion thread:
CPU A CPU B
Submit (successful)
Submit (fail)
irq_process_work_list() // empty
llist_abort_desc()
// remove all descs from pending list
irq_process_pending_llist() // empty
exit idxd_wq_thread() with no processing
Add opportunistic descriptor completion in the abort path in order to
remove the missed completion.
IPv6 allows binding a socket to a device then binding to an address
not on the device (__inet6_bind -> ipv6_chk_addr with strict flag
not set). Update the bind tests to reflect legacy behavior.
Fixes: 34d0302ab861 ("selftests: Add ipv6 address bind tests to fcnal-test") Reported-by: Li Zhijian <lizhijian@fujitsu.com> Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit referenced below added negative socket bind tests for VRF. The
socket binds should fail since the address to bind to is in a VRF yet
the socket is not bound to the VRF or a device within it. Update the
expected return code to check for 1 (bind failure) so the test passes
when the bind fails as expected. Add a 'show_hint' comment to explain
why the bind is expected to fail.
Fixes: 75b2b2b3db4c ("selftests: Add ipv4 address bind tests to fcnal-test") Reported-by: Li Zhijian <lizhijian@fujitsu.com> Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit referenced below added configuration in the default VRF that
duplicates a VRF to check MD5 passwords are properly used and fail
when expected. That config should not be added all the time as it
can cause tests to pass that should not (by matching on default VRF
setup when it should not). Move the duplicate setup to a function
that is only called for the MD5 tests and add a cleanup function
to remove it after the MD5 tests.
Fixes: 5cad8bce26e0 ("fcnal-test: Add TCP MD5 tests for VRF") Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When multiple threads concurrently access the debugfs content, data
and pointer exceptions may occur. Therefore, mutex lock protection is
added for debugfs.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the hns3_remove function firstly uninstall client instance,
and then uninstall acceletion engine device. The netdevice is freed in
client instance uninstall process, but acceletion engine device uninstall
process still use it to trace runtime information. This causes a use after
free problem.
So fixes it by check the instance register state to avoid use after free.
Fixes: d8355240cf8f ("net: hns3: add trace event support for PF/VF mailbox") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If any sub-test in this icmp_redirect.sh is failing but not expected
to fail. The script will complain:
./icmp_redirect.sh: line 72: [: 1: unary operator expected
This is because when the sub-test is not expected to fail, we won't
pass any value for the xfail local variable in log_test() and thus
it's empty. Fix this by passing 0 as the 4th variable to log_test()
for non-xfail cases.
v2: added fixes tag
Fixes: 0a36a75c6818 ("selftests: icmp_redirect: support expected failures") Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ethtool ring feature has _max_pending attributes read-only.
Set only read-write attributes in nsim_set_ringparam.
This patch is useful, if netdevsim device is set-up using NetworkManager,
because NetworkManager sends 0 as MAX values, as it is pointless to
retrieve them in extra call, because they should be read-only. Then,
the device is left in incosistent state (value > MAX).
Fixes: a7fc6db099b5 ("netdevsim: support ethtool ring and coalesce settings") Signed-off-by: Filip Pokryvka <fpokryvk@redhat.com> Link: https://lore.kernel.org/r/20211210175032.411872-1-fpokryvk@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
KMSAN reported a kernel-infoleak [1], that can exploited
by unpriv users.
After analysis it turned out UDP was not initializing
r->idiag_expires. Other users of inet_sk_diag_fill()
might make the same mistake in the future, so fix this
in inet_sk_diag_fill().
arch_kexec_apply_relocations_add currently ignores all errors returned
by arch_kexec_do_relocs. This means that every unknown relocation is
silently skipped causing unpredictable behavior while the relocated code
runs. Fix this by checking for errors and fail kexec_file_load if an
unknown relocation type is encountered.
The problem was found after gcc changed its behavior and used
R_390_PLT32DBL relocations for brasl instruction and relied on ld to
resolve the relocations in the final link in case direct calls are
possible. As the purgatory code is only linked partially (option -r)
ld didn't resolve the relocations leaving them for arch_kexec_do_relocs.
But arch_kexec_do_relocs doesn't know how to handle R_390_PLT32DBL
relocations so they were silently skipped. This ultimately caused an
endless loop in the purgatory as the brasl instructions kept branching
to itself.
Fixes: 71406883fd35 ("s390/kexec_file: Add kexec_file_load system call") Reported-by: Tao Liu <ltao@redhat.com> Signed-off-by: Philipp Rudo <prudo@redhat.com> Link: https://lore.kernel.org/r/20211208130741.5821-3-prudo@redhat.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ping6 is failing as it should.
COMMAND: ip netns exec ns-A /bin/ping6 -c1 -w1 fe80::7c4c:bcff:fe66:a63a%red
strace of ping6 shows it is failing with '1',
so change the expected rc from 2 to 1.
Fixes: c0644e71df33 ("selftests: Add ipv6 ping tests to fcnal-test") Reported-by: kernel test robot <lkp@intel.com> Suggested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jie2x Zhou <jie2x.zhou@intel.com> Link: https://lore.kernel.org/r/20211209020230.37270-1-jie2x.zhou@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
That change attempted to improve the DRM drivers fbdev emulation device
names to avoid having confusing names like "simpledrmdrmfb" in /proc/fb.
But unfortunately, there are user-space programs such as pm-utils that
match against the fbdev names and so broke after the mentioned commit.
Since the names in /proc/fb are used by tools that consider it an uAPI,
let's restore the old names even when this lead to silly names like the
one mentioned above.
Fixes: b3484d2b03e4 ("drm/fb-helper: improve DRM fbdev emulation device names") Reported-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211020165740.3011927-1-javierm@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
virtio device id value can be more than 31. Hence, use BIT_ULL in
assignment.
Fixes: 33b347503f01 ("vdpa: Define vdpa mgmt device, ops and a netlink interface") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Parav Pandit <parav@nvidia.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20211130042949.88958-1-parav@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VMADDR_CID_ANY flag used by a socket means that the socket isn't bound
to any specific CID. For example, a host vsock server may want to be bound
with VMADDR_CID_ANY, so that a guest vsock client can connect to the host
server with CID=VMADDR_CID_HOST (i.e. 2), and meanwhile, a host vsock
client can connect to the same local server with CID=VMADDR_CID_LOCAL
(i.e. 1).
The current implementation sets the destination socket's svm_cid to a
fixed CID value after the first client's connection, which isn't an
expected operation. For example, if the guest client first connects to the
host server, the server's svm_cid gets set to VMADDR_CID_HOST, then other
host clients won't be able to connect to the server anymore.
Reproduce steps:
1. Run the host server:
socat VSOCK-LISTEN:1234,fork -
2. Run a guest client to connect to the host server:
socat - VSOCK-CONNECT:2:1234
3. Run a host client to connect to the host server:
socat - VSOCK-CONNECT:1:1234
Without this patch, step 3. above fails to connect, and socat complains
"socat[1720] E connect(5, AF=40 cid:1 port:1234, 16): Connection
reset by peer".
With this patch, the above works well.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support") Signed-off-by: Wei Wang <wei.w.wang@intel.com> Link: https://lore.kernel.org/r/20211126011823.1760-1-wei.w.wang@intel.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When neither VIRTIO_PCI_LIB nor VIRTIO are enabled, but the alibaba
vdpa driver is, the kernel runs into a link error because the legacy
virtio module never gets built:
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_features':
eni_vdpa.c:(.text+0x23f): undefined reference to `vp_legacy_set_features'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_vq_state':
eni_vdpa.c:(.text+0x2fe): undefined reference to `vp_legacy_get_queue_enable'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_vq_address':
eni_vdpa.c:(.text+0x376): undefined reference to `vp_legacy_set_queue_address'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_vq_ready':
eni_vdpa.c:(.text+0x3b4): undefined reference to `vp_legacy_set_queue_address'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_free_irq':
eni_vdpa.c:(.text+0x460): undefined reference to `vp_legacy_queue_vector'
x86_64-linux-ld: eni_vdpa.c:(.text+0x4b7): undefined reference to `vp_legacy_config_vector'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_reset':
When VIRTIO_PCI_LIB was added, it was correctly added to drivers/Makefile
as well, but for the legacy module, this is missing. Solve this by always
entering drivers/virtio during the build and letting its Makefile take
care of the individual options, rather than having a separate line for
each sub-option.
If we get to the WARN_ONCE(..., "Got a HT rate (...)", ...)
here with a NULL sta, then we crash because mvmsta is bad
and we try to dereference it. Fix that by printing -1 as the
state if no station was given.
At the moment, using the ARM32 multi_v7_defconfig always results in two
SoCs being exposed in sysfs. This is wrong, as far as I'm aware the
Qualcomm DragonBoard 410c does not actually make use of a i.MX SoC. :)
This happens because imx_soc_device_init() registers the soc device
unconditionally, even when running on devices that do not make use of i.MX.
Arnd already reported this more than a year ago and even suggested a fix
similar to this commit, but for some reason it was never submitted.
Fix it by checking if the "__mxc_cpu_type" variable was actually
initialized by earlier platform code. On devices without i.MX it will
simply stay 0.
Cc: Peng Fan <peng.fan@nxp.com> Fixes: d2199b34871b ("ARM: imx: use device_initcall for imx_soc_device_init") Reported-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/CAK8P3a0hxO1TmK6oOMQ70AHSWJnP_CAq57YMOutrxkSYNjFeuw@mail.gmail.com/ Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before commit fc0c209c147f ("clk: Allow parents to be specified without
string names") child clks couldn't find their parent until the parent
clk was added to a list in __clk_core_init(). After that commit, child
clks can reference their parent clks directly via a clk_hw pointer, or
they can lookup that clk_hw pointer via DT if the parent clk is
registered with an OF clk provider.
The common clk framework treats hw->core being non-NULL as "the clk is
registered" per the logic within clk_core_fill_parent_index():
parent = entry->hw->core;
/*
* We have a direct reference but it isn't registered yet?
* Orphan it and let clk_reparent() update the orphan status
* when the parent is registered.
*/
if (!parent)
Therefore we need to be extra careful to not set hw->core until the clk
is fully registered with the clk framework. Otherwise we can get into a
situation where a child finds a parent clk and we move the child clk off
the orphan list when the parent isn't actually registered, wrecking our
enable accounting and breaking critical clks.
At this point, 'parent' points to clkBad even though clkBad hasn't been
fully registered yet. Ouch! A similar problem can happen if a clk
controller registers orphan clks that are referenced in the DT node of
another clk controller.
Let's fix all this by only setting the hw->core pointer underneath the
clk prepare lock in __clk_core_init(). This way we know that
clk_core_fill_parent_index() can't see hw->core be non-NULL until the
clk is fully registered.
Fixes: fc0c209c147f ("clk: Allow parents to be specified without string names") Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com> Link: https://lore.kernel.org/r/20211109043438.4639-1-quic_mdtipton@quicinc.com
[sboyd@kernel.org: Reword commit text, update comment] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mxsfb driver handling imx8mq lcdif doesn't yet request the
interconnect bandwidth that's needed at runtime when the description is
present in the DT node.
So remove that description and bring it back when it's supported.
The smatch static checker warned about an uninitialized symbol usage in
this function, in the case where ceph_mdsc_build_path returns an error.
It turns out that that case is harmless, but it just looks sketchy.
Initialize the variable at declaration time, and remove the unneeded
setting of it later.
Fixes: a33f6432b3a6 ("ceph: encode inodes' parent/d_name in cap reconnect message") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
opened_inodes is incremented twice when the same inode is opened twice
with O_RDONLY and O_WRONLY respectively.
To reproduce, run this python script, then check the metrics:
import os
for _ in range(10000):
fd_r = os.open('a', os.O_RDONLY)
fd_w = os.open('a', os.O_WRONLY)
os.close(fd_r)
os.close(fd_w)
Fixes: 1dd8d4708136 ("ceph: metrics for opened files, pinned caps and opened inodes") Signed-off-by: Hu Weiwen <sehuww@mail.scut.edu.cn> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For admission control, obviously all of that only works for
QoS data frames, otherwise we cannot even access the QoS
field in the header.
Syzbot reported (see below) an uninitialized value here due
to a status of a non-QoS nullfunc packet, which isn't even
long enough to contain the QoS header.
Fix this to only do anything for QoS data packets.
Dan reports that smatch has found idxd_wq_quiesce() is being called inside
the idxd->dev_lock. idxd_wq_quiesce() calls wait_for_completion() and
therefore it can sleep. Move the call outside of the spinlock as it does
not need device lock.
Add halt interrupt support. Given that the misc interrupt handler already
check halt state, the driver just need to run the halt handling code when
receiving the halt interrupt.
As stated in the schematics [1] and [2] P5 the APIO5 domain is supplied
by RK808-D Buck4, which in our case vcc1v8_codec - i.e. a 1.8 V regulator.
Currently only white noise comes from the ES8316's output, which - for
whatever reason - came up only after the the correct switch from i2s0_8ch_bus
to i2s0_2ch_bus for i2s0's pinctrl was done.
Fix this by setting the correct regulator for audio-supply.
Correct a typo in the vin-supply property. The input supply is
always-on, so this mistake doesn't affect whether the supply is actually
enabled correctly.
Correct a typo in the vin-supply property. The input supply is
always-on, so this mistake doesn't affect whether the supply is actually
enabled correctly.
On some Lenovo AMD Gen2 platforms the IRQ for the SCI and pinctrl drivers
are shared. Due to how the s2idle loop handling works, this case needs
an extra explicit check whether the interrupt was caused by SCI or by
the GPIO controller.
To fix this rework the existing IRQ handler function to function as a
checker and an IRQ handler depending on the calling arguments.
Looks like our VBIOS/GOP generally fail to turn the DP dual mode adater
TMDS output buffers back on after a reboot. This leads to a black screen
after reboot if we turned the TMDS output buffers off prior to reboot.
And if i915 decides to do a fastboot the black screen will persist even
after i915 takes over.
Apparently this has been a problem ever since commit b2ccb822d376 ("drm/i915:
Enable/disable TMDS output buffers in DP++ adaptor as needed") if one
rebooted while the display was turned off. And things became worse with
commit fe0f1e3bfdfe ("drm/i915: Shut down displays gracefully on reboot")
since now we always turn the display off before a reboot.
This was reported on a RKL, but I confirmed the same behaviour on my
SNB as well. So looks pretty universal.
Let's fix this by explicitly turning the TMDS output buffers back on
in the encoder->shutdown() hook. Note that this gets called after irqs
have been disabled, so the i2c communication with the DP dual mode
adapter has to be performed via polling (which the gmbus code is
perfectly happy to do for us).
We also need a bit of care in handling DDI encoders which may or may
not be set up for HDMI output. Specifically ddc_pin will not be
populated for a DP only DDI encoder, in which case we don't want to
call intel_gmbus_get_adapter(). We can handle that by simply doing
the dual mode adapter type check before calling
intel_gmbus_get_adapter().
Cc: <stable@vger.kernel.org> # v5.11+ Fixes: fe0f1e3bfdfe ("drm/i915: Shut down displays gracefully on reboot") Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4371 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211029191802.18448-2-ville.syrjala@linux.intel.com Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 49c55f7b035b87371a6d3c53d9af9f92ddc962db) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 57d104c153d3 ("ufs: add UFS power management support") made the UFS
driver submit a REQUEST SENSE command before submitting a power management
command to a WLUN to clear the POWER ON unit attention. Instead of
submitting a REQUEST SENSE command before submitting a power management
command, retry the power management command until it succeeds.
This is the preparation to get rid of all UNIT ATTENTION code which should
be handled by users.
Link: https://lore.kernel.org/r/20211001182015.1347587-2-jaegeuk@kernel.org Cc: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were few lockdep warnings because btrfs_show_devname() was using
device_list_mutex as recorded in the commits:
0ccd05285e7f ("btrfs: fix a possible umount deadlock") 779bf3fefa83 ("btrfs: fix lock dep warning, move scratch dev out of device_list_mutex and uuid_mutex")
And finally, commit 88c14590cdd6 ("btrfs: use RCU in btrfs_show_devname
for device list traversal") removed the device_list_mutex from
btrfs_show_devname for performance reasons.
This patch removes a stale comment about the function
btrfs_show_devname and device_list_mutex.
Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we add a device to the seed filesystem (sprouting) it is a new
filesystem (and fsid) on the device added. Update the latest_dev so
that /proc/self/mounts shows the correct device.
Reason:
While btrfs_prepare_sprout() moves the fs_devices::devices into
fs_devices::seed_list, the btrfs_show_devname() searches for the devices
and found none, leading to the warning as in above.
Fix:
latest_dev is updated according to the changes to the device list.
That means we could use the latest_dev->name to show the device name in
/proc/self/mounts, the pointer will be always valid as it's assigned
before the device is deleted from the list in remove or replace.
The RCU protection is sufficient as the device structure is freed after
synchronization.
Reported-by: Su Yue <l@damenly.su> Tested-by: Su Yue <l@damenly.su> Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to fix a bug in btrfs_show_devname().
Convert fs_devices::latest_bdev type from struct block_device to struct
btrfs_device and, rename the member to fs_devices::latest_dev.
So that btrfs_show_devname() can use fs_devices::latest_dev::name.
Tested-by: Su Yue <l@damenly.su> Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the audit daemon were ever to get stuck in a stopped state the
kernel's kauditd_thread() could get blocked attempting to send audit
records to the userspace audit daemon. With the kernel thread
blocked it is possible that the audit queue could grow unbounded as
certain audit record generating events must be exempt from the queue
limits else the system enter a deadlock state.
This patch resolves this problem by lowering the kernel thread's
socket sending timeout from MAX_SCHEDULE_TIMEOUT to HZ/10 and tweaks
the kauditd_send_queue() function to better manage the various audit
queues when connection problems occur between the kernel and the
audit daemon. With this patch, the backlog may temporarily grow
beyond the defined limits when the audit daemon is stopped and the
system is under heavy audit pressure, but kauditd_thread() will
continue to make progress and drain the queues as it would for other
connection problems. For example, with the audit daemon put into a
stopped state and the system configured to audit every syscall it
was still possible to shutdown the system without a kernel panic,
deadlock, etc.; granted, the system was slow to shutdown but that is
to be expected given the extreme pressure of recording every syscall.
The timeout value of HZ/10 was chosen primarily through
experimentation and this developer's "gut feeling". There is likely
no one perfect value, but as this scenario is limited in scope (root
privileges would be needed to send SIGSTOP to the audit daemon), it
is likely not worth exposing this as a tunable at present. This can
always be done at a later date if it proves necessary.
Cc: stable@vger.kernel.org Fixes: 5b52330bbfe63 ("audit: fix auditd/kernel connection state tracking") Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com> Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ceph always inherits the SGID bit if it is set on the parent inode,
while the generic inode_init_owner does not do this in a few cases where
it can create a possible security problem (cf. [1]).
Update ceph to strip the SGID bit just as inode_init_owner would.
This bug was detected by the mapped mount testsuite in [3]. The
testsuite tests all core VFS functionality and semantics with and
without mapped mounts. That is to say it functions as a generic VFS
testsuite in addition to a mapped mount testsuite. While working on
mapped mount support for ceph, SIGD inheritance was the only failing
test for ceph after the port.
The same bug was detected by the mapped mount testsuite in XFS in
January 2021 (cf. [2]).
[1]: commit 0fa3ecd87848 ("Fix up non-directory creation in SGID directories")
[2]: commit 01ea173e103e ("xfs: fix up non-directory creation in SGID directories")
[3]: https://git.kernel.org/fs/xfs/xfstests-dev.git
Cc: stable@vger.kernel.org Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gpio-keys already 'inherits' the interrupts from the controller
of the specified GPIO, so having another declaration is redundant.
On >=v5.15 this started causing an oops under gpio_keys_probe as
the IRQ was already claimed.
On s390, recordmcount.pl is looking for "bcrl 0,<xxx>" instructions in
the objdump -d outpout. However since binutils 2.37, objdump -d
display "jgnop <xxx>" for the same instruction. Update the
mcount_regex so that it accepts both.
This may lead to wrong results from rcu_is_cpu_rrupt_from_idle()
because of a wrong dynticks nmi nesting count. Fix this by only
calling irq_enter_rcu().
Cc: <stable@vger.kernel.org> # 5.12+ Reported-by: Mark Rutland <mark.rutland@arm.com> Fixes: 56e62a737028 ("s390: convert to generic entry") Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this function "c->off" is a u32 and "size" is a long. On 64bit systems
if "c->off" is greater than "size" then "size - c->off" is a negative and
we always return -E2BIG. But on 32bit systems the subtraction is type
promoted to a high positive u32 value and basically any "c->len" is
accepted.
Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend") Reported-by: Xie Yongji <xieyongji@bytedance.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211208103337.GA4047@kili Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
virtio_max_dma_size() returns the maximum DMA mapping size of the virtio
device by querying dma_max_mapping_size() for the device when the DMA
API is in use for the vring. Unfortunately, the device passed is
initialised by register_virtio_device() and does not inherit the DMA
configuration from its parent, resulting in SWIOTLB errors when bouncing
is enabled and the default 256K mapping limit (IO_TLB_SEGSIZE) is not
respected:
| virtio-pci 0000:00:01.0: swiotlb buffer is full (sz: 294912 bytes), total 1024 (slots), used 725 (slots)
Follow the pattern used elsewhere in the virtio_ring code when calling
into the DMA layer and pass the parent device to dma_max_mapping_size()
instead.
Cc: Marc Zyngier <maz@kernel.org> Cc: Quentin Perret <qperret@google.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Signed-off-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20211201112018.25276-1-will@kernel.org Acked-by: Jason Wang <jasowang@redhat.com> Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com> Fixes: e6d6dd6c875e ("virtio: Introduce virtio_max_dma_size()") Cc: Joerg Roedel <jroedel@suse.de> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Steven Price <steven.price@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This condition checks "len" but it does not check "offset" and that
could result in an out of bounds read if "offset > dev->config_size".
The problem is that since both variables are unsigned the
"dev->config_size - offset" subtraction would result in a very high
unsigned value.
I think these checks might not be necessary because "len" and "offset"
are supposed to already have been validated using the
vhost_vdpa_config_validate() function. But I do not know the code
perfectly, and I like to be safe.
Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211208150956.GA29160@kili Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "config.offset" comes from the user. There needs to a check to
prevent it being out of bounds. The "config.offset" and
"dev->config_size" variables are both type u32. So if the offset if
out of bounds then the "dev->config_size - config.offset" subtraction
results in a very high u32 value. The out of bounds offset can result
in memory corruption.
Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211208103307.GA3778@kili Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up unprivileged test case results for 'Dest pointer in r0' verifier tests
given they now need to reject R0 containing a pointer value, and add a couple
of new related ones with 32bit cmpxchg as well.
root@foo:~/bpf/tools/testing/selftests/bpf# ./test_verifier
#0/u invalid and of negative number OK
#0/p invalid and of negative number OK
[...]
#1268/p XDP pkt read, pkt_meta' <= pkt_data, bad access 1 OK
#1269/p XDP pkt read, pkt_meta' <= pkt_data, bad access 2 OK
#1270/p XDP pkt read, pkt_data <= pkt_meta', good access OK
#1271/p XDP pkt read, pkt_data <= pkt_meta', bad access 1 OK
#1272/p XDP pkt read, pkt_data <= pkt_meta', bad access 2 OK
Summary: 1900 PASSED, 0 SKIPPED, 0 FAILED
Given a BPF insn can only have two registers (dst, src), the R0 is fixed and
used as an auxilliary register for input (old value) as well as output (returning
old value from memory location). While the verifier performs a number of safety
checks, it misses to reject unprivileged programs where R0 contains a pointer as
old value.
Through brute-forcing it takes about ~16sec on my machine to leak a kernel pointer
with BPF_CMPXCHG. The PoC is basically probing for kernel addresses by storing the
guessed address into the map slot as a scalar, and using the map value pointer as
R0 while SRC_REG has a canary value to detect a matching address.
Fix it by checking R0 for pointers, and reject if that's the case for unprivileged
programs.
Make the bounds propagation in __reg_assign_32_into_64() slightly more
robust and readable by aligning it similarly as we did back in the
__reg_combine_64_into_32() counterpart. Meaning, only propagate or
pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the case where both s32_{min,max}_value bounds are positive, the
__reg_assign_32_into_64() directly propagates them to their 64 bit
counterparts, otherwise it pessimises them into [0,u32_max] universe and
tries to refine them later on by learning through the tnum as per comment
in mentioned function. However, that does not always happen, for example,
in mov32 operation we call zext_32_to_64(dst_reg) which invokes the
__reg_assign_32_into_64() as is without subsequent bounds update as
elsewhere thus no refinement based on tnum takes place.
Thus, not calling into the __update_reg_bounds() / __reg_deduce_bounds() /
__reg_bound_offset() triplet as we do, for example, in case of ALU ops via
adjust_scalar_min_max_vals(), will lead to more pessimistic bounds when
dumping the full register state:
Technically, the smin_value=0 and smax_value=4294967295 bounds are not
incorrect, but given the register is still a constant, they break assumptions
about const scalars that smin_value == smax_value and umin_value == umax_value.
Without the smin_value == smax_value and umin_value == umax_value invariant
being intact for const scalars, it is possible to leak out kernel pointers
from unprivileged user space if the latter is enabled. For example, when such
registers are involved in pointer arithmtics, then adjust_ptr_min_max_vals()
will taint the destination register into an unknown scalar, and the latter
can be exported and stored e.g. into a BPF map value.
Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking") Reported-by: Kuee K1r0a <liulin063@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Test whether unprivileged would be able to leak the spilled pointer either
by exporting the returned value from the atomic{32,64} operation or by reading
and exporting the value from the stack after the atomic operation took place.
Note that for unprivileged, the below atomic cmpxchg test case named "Dest
pointer in r0 - succeed" is failing. The reason is that in the dst memory
location (r10 -8) there is the spilled register r10:
The change in commit 37086bfdc737 ("bpf: Propagate stack bounds to registers
in atomics w/ BPF_FETCH") around check_mem_access() handling is buggy since
this would allow for unprivileged users to leak kernel pointers. For example,
an atomic fetch/and with -1 on a stack destination which holds a spilled
pointer will migrate the spilled register type into a scalar, which can then
be exported out of the program (since scalar != pointer) by dumping it into
a map value.
The original implementation of XADD was preventing this situation by using
a double call to check_mem_access() one with BPF_READ and a subsequent one
with BPF_WRITE, in both cases passing -1 as a placeholder value instead of
register as per XADD semantics since it didn't contain a value fetch. The
BPF_READ also included a check in check_stack_read_fixed_off() which rejects
the program if the stack slot is of __is_pointer_value() if dst_regno < 0.
The latter is to distinguish whether we're dealing with a regular stack spill/
fill or some arithmetical operation which is disallowed on non-scalars, see
also 6e7e63cbb023 ("bpf: Forbid XADD on spilled pointers for unprivileged
users") for more context on check_mem_access() and its handling of placeholder
value -1.
One minimally intrusive option to fix the leak is for the BPF_FETCH case to
initially check the BPF_READ case via check_mem_access() with -1 as register,
followed by the actual load case with non-negative load_reg to propagate
stack bounds to registers.
Fixes: 37086bfdc737 ("bpf: Propagate stack bounds to registers in atomics w/ BPF_FETCH") Reported-by: <n4ke4mry@gmail.com> Acked-by: Brendan Jackman <jackmanb@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without the bound checks for scpi_pd->name, it could result in the buffer
overflow when copying the SCPI device name from the corresponding device
tree node as the name string is set at maximum size of 30.
Let us fix it by using devm_kasprintf so that the string buffer is
allocated dynamically.
Fixes: 8bec4337ad40 ("firmware: scpi: add device power domain support using genpd") Reported-by: Pedro Batista <pedbap.g@gmail.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Cc: stable@vger.kernel.org Cc: Cristian Marussi <cristian.marussi@arm.com> Link: https://lore.kernel.org/r/20211209120456.696879-1-sudeep.holla@arm.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark TXQs as having seen transmit while they were stopped if
we bail out of drv_wake_tx_queue() due to reconfig, so that
the queue wake after this will make them catch up. This is
particularly necessary for when TXQs are used for management
packets since those TXQs won't see a lot of traffic that'd
make them catch up later.
Cc: stable@vger.kernel.org Fixes: 4856bfd23098 ("mac80211: do not call driver wake_tx_queue op during reconfig") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20211129152938.4573a221c0e1.I0d1d5daea3089be3fc0dccc92991b0f8c5677f0c@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers that do their own sequence number allocation (e.g. ath9k) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Cc: stable@vger.kernel.org Fixes: 31d8bb4e07f8 ("mac80211: agg-tx: refactor sending addba") Reported-by: Eneas U de Queiroz <cotequeiroz@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20211124094024.43222-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The KVM doesn't know whether any TLB for a specific pcid is cached in
the CPU when tdp is enabled. So it is better to flush all the guest
TLB when invalidating any single PCID context.
The case is very rare or even impossible since KVM generally doesn't
intercept CR3 write or INVPCID instructions when tdp is enabled, so the
fix is mostly for the sake of overall robustness.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211019110154.4091-2-jiangshanlai@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit f52447261bc8c2 ("KVM: irq ack notification") introduced an
ack_notifier() callback in struct kvm_pic and in struct kvm_ioapic
without using them anywhere. Remove those callbacks again.
This is not an unrecoverable situation. Users of kvm_read_guest_offset_cached
and kvm_write_guest_offset_cached must expect the read/write to fail, and
therefore it is possible to just return early with an error value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the elevated 'KVM_CAP_MAX_VCPUS' value kvm_create_max_vcpus test
may hit RLIMIT_NOFILE limits:
# ./kvm_create_max_vcpus
KVM_CAP_MAX_VCPU_ID: 4096
KVM_CAP_MAX_VCPUS: 1024
Testing creating 1024 vCPUs, with IDs 0...1023.
/dev/kvm not available (errno: 24), skipping test
Adjust RLIMIT_NOFILE limits to make sure KVM_CAP_MAX_VCPUS fds can be
opened. Note, raising hard limit ('rlim_max') requires CAP_SYS_RESOURCE
capability which is generally not needed to run kvm selftests (but without
raising the limit the test is doomed to fail anyway).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211123135953.667434-1-vkuznets@redhat.com>
[Skip the test if the hard limit can be raised. - Paolo] Reviewed-by: Sean Christopherson <seanjc@google.com> Tested-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP
response") fixed an issue in the Tegra BPMP error handling but has
exposed an issue in the Tegra194 HDA driver and now resetting the
Tegra194 HDA controller is failing. For now revert the commit c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP response")
while a fix for the Tegra HDA driver is created.
Fixes: c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP response") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20211112112712.21587-1-jonathanh@nvidia.com Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The space allowed for new attributes can be too small if existing header
information is large. That can happen, for example, if there are very
many CPUs, due to having an event ID per CPU per event being stored in the
header information.
Fix by adding the existing header.data_offset. Also increase the extra
space allowed to 8KiB and align to a 4KiB boundary for neatness.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Link: http://lore.kernel.org/lkml/20211125071457.2066863-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[Adrian: Backport to v5.15] Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In writeback cache mode mtime/ctime updates are cached, and flushed to the
server using the ->write_inode() callback.
Closing the file will result in a dirty inode being immediately written,
but in other cases the inode can remain dirty after all references are
dropped. This result in the inode being written back from reclaim, which
can deadlock on a regular allocation while the request is being served.
The usual mechanisms (GFP_NOFS/PF_MEMALLOC*) don't work for FUSE, because
serving a request involves unrelated userspace process(es).
Instead do the same as for dirty pages: make sure the inode is written
before the last reference is gone.
- fallocate(2)/copy_file_range(2): these call file_update_time() or
file_modified(), so flush the inode before returning from the call
- unlink(2), link(2) and rename(2): these call fuse_update_ctime(), so
flush the ctime directly from this helper
Commit 723de0f9171e ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem. This updated dim2 driver as well.
However, struct device passed to register_device() becomes refcounted,
and must not be explicitly deallocated, but must provide release method
instead. Which is incompatible with managing it via devres.
This patch makes the device structure allocated without devres, adds
device release method, and moves device destruction there.
The reason is elts->pages[i] is alloced by get_zeroed_page.
and kmemleak will not scan the area alloced by get_zeroed_page.
The address stored in elts->pages will be regarded as leaked.
That is, the elts->pages[i] will have pointers loaded onto it as well, and
without telling kmemleak about it, those pointers will look like memory
without a reference.
To fix this, call kmemleak_alloc to tell kmemleak to scan elts->pages[i]
process_info->lock is used to protect kfd_bo_list, vm_list_head, n_vms
and userptr valid/inval list, svm_range_restore_work and
svm_range_set_attr don't access those, so do not need to take
process_info lock. This will avoid potential circular locking issue.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
IGT bypass test will set crc source as DPRX,and display DM didn`t check
connection type, it run the test on the HDMI connector ,then the kernel
will be crashed because aux->transfer is set null for HDMI connection.
This patch will skip the invalid connection test and fix kernel crash issue.
[How]
Check the connector type while setting the pipe crc source as DPRX or
auto,if the type is not DP or eDP, the crtc crc source will not be set
and report error code to IGT test,IGT will show the this subtest as no
valid crtc/connector combinations found.
drm_gem_object_put calls release_notify callback to free the mem
structure and unreserve_mem_limit, move it down after the last access
of mem and make it conditional call.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
It seems like after a series of plug/unplugs we end up in a situation
where tiled display doesnt support Audio.
[HOW]
The issue seems to be related to when we check streams changed after an
HPD, we should be checking the audio_struct as well to see if any of its
values changed.
Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding a check on len parameter to avoid empty skb. This prevents a
division error in netem_enqueue function which is caused when skb->len=0
and skb->data_len=0 in the randomized corruption step as shown below.
projects / thirdparty / kernel / stable.git / log
