Jun Nie [Thu, 18 Sep 2025 13:29:02 +0000 (21:29 +0800)]
drm/msm/dpu: Enable quad-pipe for DSC and dual-DSI case
To support high-resolution cases that exceed the width limitation of
a pair of SSPPs, or scenarios that surpass the maximum MDP clock rate,
additional pipes are necessary to enable parallel data processing
within the SSPP width constraints and MDP clock rate.
Request 4 mixers and 4 DSCs for high-resolution cases where both DSC
and dual interfaces are enabled. More use cases can be incorporated
later if quad-pipe capabilities are required.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675418/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-10-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Jun Nie [Thu, 18 Sep 2025 13:29:01 +0000 (21:29 +0800)]
drm/msm/dpu: support plane splitting in quad-pipe case
The content of every half of screen is sent out via one interface in
dual-DSI case. The content for every interface is blended by a LM
pair in quad-pipe case, thus a LM pair should not blend any content
that cross the half of screen in this case. Clip plane into pipes per
left and right half screen ROI if topology is quad pipe case.
The clipped rectangle on every half of screen is futher handled by two
pipes if its width exceeds a limit for a single pipe.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/675416/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-9-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Jun Nie [Thu, 18 Sep 2025 13:29:00 +0000 (21:29 +0800)]
drm/msm/dpu: support SSPP assignment for quad-pipe case
Currently, SSPPs are assigned to a maximum of two pipes. However,
quad-pipe usage scenarios require four pipes and involve configuring
two stages. In quad-pipe case, the first two pipes share a set of
mixer configurations and enable multi-rect mode when certain
conditions are met. The same applies to the subsequent two pipes.
Assign SSPPs to the pipes in each stage using a unified method and
to loop the stages accordingly.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Reviewed-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/675414/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-8-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Jun Nie [Thu, 18 Sep 2025 13:28:59 +0000 (21:28 +0800)]
drm/msm/dpu: blend pipes per mixer pairs config
Currently, only 2 pipes are used at most for a plane. A stage structure
describes the configuration for a mixer pair. So only one stage is needed
for current usage cases. The quad-pipe case will be added in future and 2
stages are used in the case. So extend the stage to an array with array
size STAGES_PER_PLANE and blend pipes per mixer pair with configuration in
the stage structure.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675412/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-7-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Jun Nie [Thu, 18 Sep 2025 13:28:58 +0000 (21:28 +0800)]
drm/msm/dpu: Use dedicated WB number definition
Currently MAX_CHANNELS_PER_ENC is defined as 2, because 2 channels are
supported at most in one encoder. The case of 4 channels per encoder is
to be added. To avoid breaking current WB usage case, use dedicated WB
definition before 4 WB usage case is supported in future.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675410/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-6-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Jun Nie [Thu, 18 Sep 2025 13:28:57 +0000 (21:28 +0800)]
drm/msm/dpu: split PIPES_PER_STAGE definition per plane and mixer
The stage contains configuration for a mixer pair. Currently the plane
supports just one stage and 2 pipes. Quad-pipe support will require
handling 2 stages and 4 pipes at the same time. In preparation for that
add a separate define, PIPES_PER_PLANE, to denote number of pipes that
can be used by the plane.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675408/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-5-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Jun Nie [Thu, 18 Sep 2025 13:28:56 +0000 (21:28 +0800)]
drm/msm/dpu: handle pipes as array
There are 2 pipes in a drm plane at most currently, while 4 pipes are
required for quad-pipe case. Generalize the handling to pipe pair and
ease handling to another pipe pair later. Store pipes in array with
removing dedicated r_pipe.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675406/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-4-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Jun Nie [Thu, 18 Sep 2025 13:28:53 +0000 (21:28 +0800)]
drm/msm/dpu: fix mixer number counter on allocation
Current code only supports usage cases with one pair of mixers at
most. To support quad-pipe usage case, two pairs of mixers need to
be reserved. The lm_count for all pairs is cleared if a peer
allocation fails in current implementation. Reset the current lm_count
to an even number instead of completely clearing it. This prevents all
pairs from being cleared in cases where multiple LM pairs are needed.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/675400/ Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-1-ff6232e3472f@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
drm/msm: fix allocation of dumb buffers for non-RGB formats
Several users (including IGT kms_getfb tests) allocate DUMB buffers for
YUV data. Commit 538fa012cbdb ("drm/msm: Compute dumb-buffer sizes with
drm_mode_size_dumb()") broke that usecase, since in those cases
drm_driver_color_mode_format() returns DRM_FORMAT_INVALID.
Handle the YUV usecase, aligning to 32-bit pixels.
Fixes: 538fa012cbdb ("drm/msm: Compute dumb-buffer sizes with drm_mode_size_dumb()") Closes: https://lore.kernel.org/all/vptw5tquup34e3jen62znnw26qe76f3pys4lpsal5g3czwev6y@2q724ibos7by/ Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/685197/
Message-ID: <20251103-drm-msm-fix-nv12-v2-1-75103b64576e@oss.qualcomm.com> Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Simona Vetter [Fri, 31 Oct 2025 17:57:54 +0000 (18:57 +0100)]
Merge tag 'drm-intel-gt-next-2025-10-29' of https://gitlab.freedesktop.org/drm/i915/kernel into drm-next
Driver Changes:
Fixes/improvements/new stuff:
- Set O_LARGEFILE in __create_shmem() (Taotao Chen)
- Fix incorrect error handling in shmem_pwrite() (Taotao Chen)
- Skip GuC communication warning on reset in progress [guc] (Zhanjun Dong)
- Fix conversion between clock ticks and nanoseconds [guc] (Umesh Nerlige Ramappa)
Miscellaneous:
- Avoid accessing uninitialized context in emit_rpcs_query() [selftests] (Krzysztof Karas)
- Fix typo in comment (I915_EXEC_NO_RELOC) [gem] (Marlon Henrique Sanches)
Backmerges:
- Merge drm/drm-next into drm-intel-gt-next (Joonas Lahtinen)
Simona Vetter [Fri, 31 Oct 2025 17:47:16 +0000 (18:47 +0100)]
Merge tag 'drm-misc-next-2025-10-28' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for v6.19-rc1:
UAPI Changes:
Cross-subsystem Changes:
- Update DT bindings for renesas and powervr-rogue.
- Update MAINTAINERS email and add spsc_queue.
Core Changes:
- Allow ttm page protection flags on risc-v.
- Move freeing of drm client memory to driver.
Driver Changes:
- Assorted small fixes and updates to qaic, ivpu, st7571-i2c, gud,
amdxdna.
- Allow configuration of vkms' display through configfs.
- Add Arm Ethos-U65/U85 accel driver.
Simona Vetter [Fri, 31 Oct 2025 17:40:53 +0000 (18:40 +0100)]
Merge tag 'drm-xe-next-2025-10-28' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
Driver Changes:
More xe3p support (Harish, Brian, Balasubramani, Matt Roper)
Make panic support work on VRAM for display (Maarten)
Fix stolen size check (Shuicheng)
xe_pci_test update (Gustavo)
VF migration updates (Tomasz)
A couple of fixes around allocation and PM references (Matt Brost)
Migration update for the MEM_COPY instruction (Matt Auld)
Initial CRI support (Balasubramani, Matt Roper)
Use SVM range helpers in PT layer (Matt Brost)
Drop MAX_GT_TYPE_CHARS constant (Matt Roper)
Fix spelling and typos (Sanjay)
Fix VF FLR synchronization between all GTs (Michal)
Add a Workaround (Nitin)
Access VF's register using dedicated MMIO view (Michal)
drm/msm/dpu: Fix adjusted mode clock check for 3d merge
Since 3D merge allows for larger modes to be supported across 2 layer
mixers, filter modes based on adjusted mode clock / 2 when 3d merge is
supported.
Reported-by: Abel Vesa <abel.vesa@linaro.org> Fixes: 62b7d6835288 ("drm/msm/dpu: Filter modes based on adjusted mode clock") Signed-off-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Tested-by: Abel Vesa <abel.vesa@linaro.org> Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/676353/ Link: https://lore.kernel.org/r/20250923-modeclk-fix-v2-1-01fcd0b2465a@oss.qualcomm.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Vladimir Lypak [Sat, 18 Oct 2025 14:33:43 +0000 (14:33 +0000)]
drm/msm/dpu: Disable broken YUV on QSEED2 hardware
YUV formats on this hardware needs scaling for chroma planes. However it
is not implemented for QSEED2 which breaks display pipeline if YUV format
is used (causing partial and corrupted output with PPDONE timeouts).
This patch temporarily disables YUV by switching affected sub-block to
RGB only format list.
Fixes: daf9a92daeb8 ("drm/msm/dpu: Add support for MSM8996") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/682061/ Link: https://lore.kernel.org/r/20251018-b4-dpu-fixes-v1-6-1852278064d0@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Vladimir Lypak [Fri, 17 Oct 2025 19:58:39 +0000 (19:58 +0000)]
drm/msm/dpu: Require linear modifier for writeback framebuffers
UBWC-related register configuration for writeback is not implemented in
the driver yet but there aren't any checks for non-linear modifiers in
atomic_check. Thus when compressed framebuffer is attached to writeback
connector it will be filled with linear image data. This patch forbids
non-linear modifiers for writeback framebuffers until UBWC support for
writeback is properly implemented.
Vladimir Lypak [Fri, 17 Oct 2025 19:58:38 +0000 (19:58 +0000)]
drm/msm/dpu: Fix pixel extension sub-sampling
In _dpu_plane_setup_pixel_ext function instead of dividing just chroma
source resolution once (component 1 and 2), second component is divided
once more because src_w and src_h variable is reused between iterations.
Third component receives wrong source resolution too (from component 2).
To fix this introduce temporary variables for each iteration.
Fixes: dabfdd89eaa9 ("drm/msm/disp/dpu1: add inline rotation support for sc7280") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681921/ Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-4-40ce5993eeb6@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Vladimir Lypak [Fri, 17 Oct 2025 19:58:37 +0000 (19:58 +0000)]
drm/msm/dpu: Disable scaling for unsupported scaler types
Scaling is not implemented for some type of scalers (QSEED2 and RGB) but
it was unintentionally re-enabled with change below. The remaining
condition in dpu_plane_atomic_check_pipe is not enough because it only
checks for length of scaler block (which is present). This patch adds a
additional check for setup_scaler operation.
Fixes: 8f15005783b8 ("drm/msm/dpu: move scaling limitations out of the hw_catalog") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681918/ Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-3-40ce5993eeb6@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Vladimir Lypak [Fri, 17 Oct 2025 19:58:36 +0000 (19:58 +0000)]
drm/msm/dpu: Propagate error from dpu_assign_plane_resources
The dpu_plane_virtual_assign_resources function might fail if there is
no suitable SSPP(s) for the plane. This leaves sspp field in plane
state uninitialized and later leads to NULL dereference during commit:
Vladimir Lypak [Fri, 17 Oct 2025 19:58:35 +0000 (19:58 +0000)]
drm/msm/dpu: Fix allocation of RGB SSPPs without scaling
Due to condition in dpu_rm_reserve_sspp, RGB SSPPs are only tried when
scaling is requested, which prevents those SSPPs from being reserved if
we don't need scaling at all. Instead we should check if YUV support is
requested, since scaling on RGB SSPPs is optional and is not implemented
in driver yet.
Fixes: 774bcfb73176 ("drm/msm/dpu: add support for virtual planes") Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681914/ Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-1-40ce5993eeb6@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Neil Armstrong [Mon, 27 Oct 2025 13:09:48 +0000 (14:09 +0100)]
drm/msm: dsi: fix PLL init in bonded mode
When in bonded DSI mode, only one PLL in one DSI PHY is used for both
DSI PHYs, meaning that parents of the secondary DSI PHY will use the
primary DSI PHY PLL as parent.
In this case the primary DSI PHY PLL will be set even if the primary
DSI PHY is not yet enabled. The DSI PHY code has support for this
particular use-case and will handle the fact the PLL was already
set when initializing the primary DSI PHY.
By introducing a protected variable pll_enable_cnt in the commit cb55f39bf7b1 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared"),
this variable is only initially set to 1 when the DSI PHY is initialized
making it impossible to set the PLL before, breaking the bonded DSI
use case by returning 0 when setting the PLL from the secondary DSI
PHY driver and skipping the correct clocks initialization.
But since it was already possible to set the PLL without enabling
the DSI PHY, just drop the pll_enable_cnt setting from the PHY
enable/disable and simply increment/decrement the pll_enable_cnt
variable from the dsi_pll_enable/disable_pll_bias to make sure any
PLL operation is done with the PLL BIAS enabled.
Fixes: cb55f39bf7b1 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared") Closes: https://lore.kernel.org/all/50a49d72-2b1e-471d-b0c4-d5a0b38b2a21@linaro.org/ Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/683688/ Link: https://lore.kernel.org/r/20251027-topic-sm8x50-fix-dsi-bonded-v1-1-a477cd3f907d@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-redundant explicit call to
pm_runtime_mark_last_busy().
Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-redundant explicit call to
pm_runtime_mark_last_busy().
Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:02:03 +0000 (20:02 +0200)]
drm/amdgpu: Use DC by default for Bonaire
Now that DC supports analog connectors, there is nothing stopping
us from using it by default on Bonaire.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:02:02 +0000 (20:02 +0200)]
drm/amd/display: Don't add freesync modes to analog displays (v2)
VRR is not supported on analog signals.
Don't add freesync modes to analog displays or when
VRR is unsupported by DC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:02:01 +0000 (20:02 +0200)]
drm/amd/display: Add common modes to analog displays without EDID
When the EDID of an analog display is not available, we can't
know the possible modes supported by the display. However, we
still need to offer the user to select from a variety of common
modes. It will be up to the user to select the best one, though.
This is how it works on other operating systems as well as the
legacy display code path in amdgpu.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:02:00 +0000 (20:02 +0200)]
drm/amd/display: Use DAC load detection on analog connectors (v2)
This feature is useful for analog connections without EDID:
- Really old monitors with a VGA connector
- Cheap DVI/VGA adapters that don't connect DDC pins
When a connection is established through DAC load detection,
the driver is supposed to fill in the supported modes for the
display, which we already do in amdgpu_dm_connector_get_modes.
Also, because the load detection causes visible glitches, do not
attempt to poll the connector again after it was detected this
way. Note that it will still be polled after sleep/resume or
when force is enabled, which is okay.
v2:
Add dc_connection_dac_load connection type.
Properly release sink when no display is connected.
Don't print error when EDID isn't read from an analog display.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:59 +0000 (20:01 +0200)]
drm/amd/display: Add DAC_LoadDetection to BIOS parser (v2)
DAC_LoadDetection can be used to determine whether something
is connected to an analog connector by determining if there is
an analog load. This causes visible flickering on displays, so
we only resort to using this when the connected display doesn't
have an EDID.
For reference, see the legacy display code:
amdgpu_atombios_encoder_dac_load_detect
v2:
Only clear corresponding bit from BIOS_SCRATCH_0.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:58 +0000 (20:01 +0200)]
drm/amd/display: Make get_support_mask_for_device_id reusable
This will be reused by DAC load detection.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:57 +0000 (20:01 +0200)]
drm/amd/display: Add DCE BIOS_SCRATCH_0 register
The BIOS uses this register to write the results of the
DAC_LoadDetection command, so we'll need to read this
in order to make DAC load detection work.
As a reference, I used the mmBIOS_SCRATCH_0 definition from
the amdgpu legacy display code.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:56 +0000 (20:01 +0200)]
drm/amd/display: Poll analog connectors (v3)
VGA connectors don't support any hotplug detection, so the kernel
needs to periodically poll them to see if a display is connected.
DVI-I connectors have hotplug detection for digital signals, and
some analog DVI cables pull up that pin to work with that.
However, in general not all DVI cables do this so we can't rely on
this feature, therefore we need to poll DVI-I connectors as well.
v2:
Call drm_kms_helper_poll_fini in amdgpu_dm_hpd_fini.
Disable/enable polling on suspend/resume.
Don't call full link detection when already connected.
v3:
Encounter CLANG build failure. Remove unused variable:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_irq.c:980:7:
error: variable 'use_polling' set but not used [-Werror,-Wunused-but-
set-variable]
980 | bool use_polling = false;
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prepare for polling analog connectors.
Document the function better.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:54 +0000 (20:01 +0200)]
drm/amd/display: Add analog link detection (v2)
Analog displays typically have a DDC connection which can be
used by the GPU to read EDID. This commit adds the capability
to probe analog displays using DDC, reading the EDID header and
deciding whether the analog link is connected based on the data
that was read.
Note that VGA has no HPD (hotplug detection), so we need to
to do analog link detection for VGA before checking HPD.
In case of DVI-I, while the connector supports HPD, not all
analog cables connect the HPD pins, so we can't rely on HPD
either.
For reference, see the legacy display code:
amdgpu_connector_vga_detect
amdgpu_display_ddc_probe
DAC load detection will be implemented in a separate commit.
v2:
Fix crash / black screen on newer GPUs during link detection.
Ignore HPD pin for analog connectors.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:53 +0000 (20:01 +0200)]
drm/amd/display: Support DAC in dce110_hwseq
The dce110_hwseq is used by all DCE hardware,
so add the DAC support here.
When enabling/disabling a stream for a RGB signal,
this will call the VBIOS to enable/disable the DAC.
Additionally, when applying the controller context,
call SelectCRTC_Source from VBIOS in order to
direct the CRTC output to the DAC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:52 +0000 (20:01 +0200)]
drm/amd/display: Implement DCE analog link encoders (v2)
We support two kinds of analog connections:
1. DVI-I, which allows both digital and analog signals:
The DC code base only allows 1 encoder per connector, and the
preferred engine type is still going to be digital. So, for DVI-I
to work, we need to make sure the pre-existing link encoder can
also work with analog signals.
1. VGA, which only supports analog signals:
For VGA, we need to create a link encoder that only works with the
DAC without perturbing any digital transmitter functionality.
Since dce110_link_encoder already supports analog DVI-I,
just reuse that code for VGA as well.
v2:
Reduce code churn by reusing same link encoder for VGA and DVI-I.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:51 +0000 (20:01 +0200)]
drm/amd/display: Implement DCE analog stream encoders
Add analog stream encoders for DCE which will be used when
connecting an analog display through VGA or DVI-I.
Considering that all stream encoder functions currently deal
with digital streams, there is nothing for an analog stream
encoder to do, making them basically a no-op.
That being said, we still need some kind of stream encoder to
represent an analog stream, and it is beneficial to split them
from digital stream encoders in the code to make sure they
don't accidentally write any DIG* registers.
On supported chips there is currently up to 1 analog encoder,
which is DACA. There are references to DACB in some code such
as VBIOS commands and register files but it seems to be
not present on DCE 6 and newer.
Set num_analog_stream_encoder = 1 so that we can support
the analog connectors on DCE 6-10, for now.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:50 +0000 (20:01 +0200)]
drm/amd/display: Add concept of analog encoders (v2)
Add a num_analog_stream_encoders field to indicate how many
analog stream encoders are present. When analog stream encoders
are present, create them.
Additionally, add an analog_engine field to link encoders and
search for supported analog encoders in the BIOS for each link.
When connecting an RGB signal, search for analog stream encoders.
The actual DCE analog link and stream encoder is going to be
added in a subsequent commit.
v2:
Add check to see if an analog engine is really supported.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:49 +0000 (20:01 +0200)]
drm/amd/display: Determine early if a link has supported encoders (v2)
Avoid initializing DDC, HPD, etc. when we know that the link is
not going to be constructed because it has no supported encoders.
This is mainly useful for old GPUs which may have encoders such
as TRAVIS and NUTMEG that are not yet supported by DC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:48 +0000 (20:01 +0200)]
drm/amd/display: Don't try to enable/disable HPD when unavailable
VGA connectors don't have HPD (hotplug detection), so don't
touch any HPD related registers for VGA.
Determine whether hotplug detection is available by checking that
the interrupt source is invalid.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:47 +0000 (20:01 +0200)]
drm/amd/display: Don't use stereo sync and audio on RGB signals (v2)
Analog video signals on VGA or DVI-A (analog part of DVI-I)
don't support audio, so avoid calling any audio related
functions on analog signals.
Stereo sync was not set up for analog signals in the legacy
display code either, so there is no loss of functionality if
we omit it from DC for now.
Also add a dc_is_rgb_signal similar to other dc_is_*_signal.
v2:
Added comment to clarify what we mean by RGB in this context.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:46 +0000 (20:01 +0200)]
drm/amd/display: Get maximum pixel clock from VBIOS
We will use this for validating the pixel clock when
an analog monitor is connected to VGA or DVI-I connectors.
For reference, see the legacy display code:
amdgpu_connector_vga_mode_valid
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:45 +0000 (20:01 +0200)]
drm/amd/display: Add SelectCRTC_Source to BIOS parser
The SelectCRTC_Source command will be used to change which CRTC
should be connected to which encoder.
For reference, see the legacy display code:
amdgpu_atombios_encoder_set_crtc_source
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:44 +0000 (20:01 +0200)]
drm/amd/display: Hook up DAC to bios_parser_encoder_control
Enable the codebase to use encoder_control()
when the encoder engine is one of the DACs.
The BIOS parser already supports calling the DAC1EncoderControl
function from the VBIOS, but it was not exposed anywhere.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:43 +0000 (20:01 +0200)]
drm/amd/display: Introduce MAX_LINK_ENCODERS (v2)
We are going to support analog encoders as well, not just digital,
so we need to make space for them in various arrays.
v2: Fix typo.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:42 +0000 (20:01 +0200)]
drm/amd/display: Add analog bit to edid_caps (v2)
The new analog bit will be used with DVI-I connectors.
DVI-I connectors can connect to both digital and analog monitors
and this bit will help distinguish between those.
v2:
Sanitize analog bit based on connector type.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdkfd: Fix use-after-free of HMM range in svm_range_validate_and_map()
The function svm_range_validate_and_map() was freeing `range` when
amdgpu_hmm_range_get_pages() failed. But later, the code still used the
same `range` pointer and freed it again. This could cause a
use-after-free and double-free issue.
The fix sets `range = NULL` right after it is freed and checks for
`range` before using or freeing it again.
v2: Removed duplicate !r check in the condition for clarity.
v3: In amdgpu_hmm_range_get_pages(), when hmm_range_fault() fails, we
kvfree(pfns) but leave the pointer in hmm_range->hmm_pfns still pointing
to freed memory. The caller (or amdgpu_hmm_range_free(range)) may try to
free range->hmm_range.hmm_pfns again, causing a double free, Setting
hmm_range->hmm_pfns = NULL immediately after kvfree(pfns) prevents both
double free. (Philip)
In svm_range_validate_and_map(), When r == 0, it means success → range
is not NULL. When r != 0, it means failure → already made range = NULL.
So checking both (!r && range) is unnecessary because the moment r == 0,
we automatically know range exists and is safe to use. (Philip)
Fixes: 737da5363cc0 ("drm/amdgpu: update the functions to use amdgpu version of hmm")
Reported by: Dan Carpenter <dan.carpenter@linaro.org> Cc: Philip Yang <Philip.Yang@amd.com> Cc: Sunil Khatri <sunil.khatri@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Philip Yang<Philip.Yang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 10 Oct 2025 19:21:02 +0000 (15:21 -0400)]
drm/amdgpu/userq: fix SDMA and compute validation
The CSA and EOP buffers have different alignement requirements.
Hardcode them for now as a bug fix. A proper query will be added in
a subsequent patch.
v2: verify gfx shadow helper callback (Prike)
Fixes: 9e46b8bb0539 ("drm/amdgpu: validate userq buffer virtual address and size") Reviewed-by: Prike Liang <Prike.Liang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Philip Yang [Wed, 15 Oct 2025 19:17:54 +0000 (15:17 -0400)]
drm/amdkfd: Dequeue user queues when process mm released
Move dequeue user queues and destroy user queues from
kfd_process_wq_release to mmu notifier release callback, to ensure no
system memory access from GPU because the process memory is going to
free from CPU after mmu release notifier callback returns.
Destroy queue releases the svm prange queue_refcount, this also removes
fake flase positive warning message "Freeing queue vital buffer" message
if application crash or killed.
Suggested-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Timur Kristóf [Fri, 26 Sep 2025 18:01:41 +0000 (20:01 +0200)]
drm/amd/display: Determine DVI-I connector type (v2)
DC determines the DRM connector type based on the
signal type, which becomes problematic when a connector may
support different signal types, such as DVI-I.
With this patch, it is now determined according to the actual
connector type for DVI-D and DVI-I connectors.
Also set the HPD (hotplug detection) flag for DVI-I connectors
to prevent regressing their digital functionality, which has
been already working.
A subsequent commit will also implement polling for DVI-I.
v2:
Only use connector type for DVI to prevent regressions
for other signal types.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jesse.Zhang [Tue, 21 Oct 2025 05:01:06 +0000 (13:01 +0800)]
drm/amdgpu: Convert amdgpu userqueue management from IDR to XArray
This commit refactors the AMDGPU userqueue management subsystem to replace
IDR (ID Allocation) with XArray for improved performance, scalability, and
maintainability. The changes address several issues with the previous IDR
implementation and provide better locking semantics.
Key changes:
1. **Global XArray Introduction**:
- Added `userq_doorbell_xa` to `struct amdgpu_device` for global queue tracking
- Uses doorbell_index as key for efficient global lookup
- Replaces the previous `userq_mgr_list` linked list approach
2. **Per-process XArray Conversion**:
- Replaced `userq_idr` with `userq_mgr_xa` in `struct amdgpu_userq_mgr`
- Maintains per-process queue tracking with queue_id as key
- Uses XA_FLAGS_ALLOC for automatic ID allocation
3. **Locking Improvements**:
- Removed global `userq_mutex` from `struct amdgpu_device`
- Replaced with fine-grained XArray locking using XArray's internal spinlocks
4. **Runtime Idle Check Optimization**:
- Updated `amdgpu_runtime_idle_check_userq()` to use xa_empty
Benefits:
- **Performance**: XArray provides better scalability for large numbers of queues
- **Memory Efficiency**: Reduced memory overhead compared to IDR
- **Thread Safety**: Improved locking semantics with XArray's internal spinlocks
v2: rename userq_global_xa/userq_xa to userq_doorbell_xa/userq_mgr_xa
Remove xa_lock and use its own lock.
v3: Set queue->userq_mgr = uq_mgr in amdgpu_userq_create()
v4: use xa_store_irq (Christian)
hold the read side of the reset lock while creating/destroying queues and the manager data structure. (Chritian)
Acked-by: Alex Deucher <alexander.deucher@amd.com> Suggested-by: Christian König <christian.koenig@amd.com> Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Taimur Hassan [Sat, 18 Oct 2025 00:22:02 +0000 (19:22 -0500)]
drm/amd/display: Promote DC to 3.2.356
This version brings along following update:
- Fix incorrect return of vblank enable on unconfigured crtc
- Add HDR workaround for a specific eDP
- Make observers const-correct
- Add lock descriptor to check_update
- Update cursor offload assignments
- Add dc interface to log pre os firmware information
- Init dispclk from bootup clock for DCN315
- Remove dc param from check_update
- Update link encoder assignment
- Add more DC HW state info to underflow logging
- Rename dml2 to dml2_0 folder
- Fix notification of vtotal to DMU for cursor offload
- Fix wrong index for DCN401 cursor offload
- Add opp count validation to dml2.1
- Fix DMUB reset sequence for DCN32
- Bump minimum for frame_warn_limit
Acked-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Taimur Hassan [Fri, 17 Oct 2025 21:20:46 +0000 (17:20 -0400)]
drm/amd/display: [FW Promotion] Release 0.1.33.0
[Why & How]
- Extend reply debug flags, define a new bit as debug_log_enabled
- Replace the padding to frame_skip_number in struct
dmub_cmd_replay_set_coasting_vtotal_data
Acked-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Fri, 17 Oct 2025 02:08:10 +0000 (20:08 -0600)]
drm/amd/display: Add HDR workaround for a specific eDP
[WHY & HOW]
Some eDP panels suffer from flicking when HDR is enabled in KDE or
Gnome.
This add another quirk to worksaround to skip VSC that is incompatible
with an eDP panel.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/4452 Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Observers which do not modify their pointer arguments should take
them as const. This clearly signals their intent to the caller,
making it clear that the function is safe to call multiple times,
or remove the call if the result is no longer necessary.
[How]
Made const-correct all of the functions below:
* full_update_required[_weak]
* fast_updates_exist
* fast_update_only
* dc_can_clear_cursor_limit
* dc_stream_get_status (added const named overload)
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Add lock descriptor to check_update
[Why]
DM locks the global DC lock during all updates, even if multiple
updates touch different resources and could be run in parallel.
[How]
Add extra enum specifying which kind of resources should be locked.
Reviewed-by: Aric Cyr <aric.cyr@amd.com> Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Cursor lines per chunk must be assigned from hubp->att and not
hubp->pos (the one in hubp->pos is unassigned)
- In DCN401 DPP, cur0_enable in attribute struct must be assigned
as this is the field passed to DMU
- DCN401 should not program position in driver if offload is enabled
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Add dc interface to log pre os firmware information
[Why]
Pre os firmware information is useful to debug pre os to post os fw
transition issues.
[How]
Add dc interface dc_log_preos_dmcub_info() to log pre os firmware
information.
Reviewed-by: Cruise Hung <cruise.hung@amd.com> Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Zhongwei Zhang [Tue, 14 Oct 2025 02:46:49 +0000 (10:46 +0800)]
drm/amd/display: init dispclk from bootup clock for DCN315
[Why]
Driver does not pick up and save vbios's clocks during init clocks,
the dispclk in clk_mgr will keep 0.
OS might change the timing (lower the pixel clock) after boot.
Then driver will set the dispclk to lower when safe_to_lower is false,
for in clk_mgr dispclk is zero, it's illegal and causes garbage.
[How]
Dump and save the vbios's clocks, and init the dispclk in
dcn315_init_clocks.
Reviewed-by: Charlene Liu <charlene.liu@amd.com> Signed-off-by: Zhongwei Zhang <Zhongwei.Zhang@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Remove dc param from check_update
[Why]
dc_check_update_surfaces_for_stream should not have access to entire
DC, especially not a mutable one. Concurrent checks should be able
to run independently of one another, without risk of changing state.
[How]
* Replace dc and stream_status structs with new dc_check_config.
* Move required fields from dc_debug and dc_caps to dc_check_config.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Map a link encoder instance matching stream encoder instance
if possible.
[How]
Get the stream encoder instance and assign the same link
encoder instance if available.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com> Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Karen Chen [Wed, 15 Oct 2025 15:13:07 +0000 (11:13 -0400)]
drm/amd/display: Add more DC HW state info to underflow logging
[Why]
Debugging underflow issues frequently requires knowing the
HW state at the time of underflow. To enable capturing this
HW state information, interface functions are needed for the
various DC HW blocks.
[How]
This change adds the interface functions to read HW state for
the following DC HW blocks:
- HUBBUB
- HUBP
- DPP
- MPC
- OPP
- DSC
- OPTC
- DCCG
Reviewed-by: George Shen <george.shen@amd.com> Signed-off-by: Karen Chen <Karen.Chen@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Austin Zheng [Tue, 21 Oct 2025 05:52:58 +0000 (13:52 +0800)]
drm/amd/display: Rename dml2 to dml2_0 folder
[Why]
dml2 folder contains all logic for all versions of DML2
This is currently DML2.0 and DML2.1.
Rename dml2 to dml2_0 folder to reflect this better (dml2_0
for DML2.0).
[How]
Rename dml2 to dml2_0 folder and update dml2 references to
use dml2_0 folder.
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Austin Zheng <Austin.Zheng@amd.com> Signed-off-by: waynelin <Wayne.Lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Fix notification of vtotal to DMU for cursor offload
[Why]
It was placed after the early return and the notification is never sent.
[How]
Place it after .set_drr and before the return.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Fix wrong index for DCN401 cursor offload
[Why]
Payloads are ignored because the wrong index is written as part of the
pipe update implementation for DCN401.
[How]
Align it to the DCN35 implementation and ensure the + 1 is added.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Add opp count validation to dml2.1
Newer asics can have mismatching dpp and opp counts and
dml needs to account for this.
Reviewed-by: Charlene Liu <charlene.liu@amd.com> Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Fix DMUB reset sequence for DCN32
[WHY&HOW]
Backport reset sequence fixes implemented on DCN401 to DCN32 to address
stability issues when resetting the DMUB.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Dillon Varone <Dillon.Varone@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Bump minimum for frame_warn_limit
[Why]
The bigger of CONFIG_FRAME_WARN and frame_warn_limit is used to
trigger warnings about large stack frames. The dml_core_mode_support()
stack frame has grown to 2056.
[How]
Update frame_warn_limit to 2056 so that CONFIG_FRAME_WARN of 2048 doesn't
cause a failure.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4609 Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Mario Limonciello <superm1@kernel.org> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd: Re-introduce property to control adaptive backlight modulation
commit 0887054d14ae ("drm/amd: Drop abm_level property") dropped the
abm level property in favor of sysfs control. Since then there have
been discussions that compositors showed an interest in modifying
a vendor specific property instead.
So re-introduce the abm level property, but with different semantics.
Rather than being an integer it's now an enum. One of the enum options
is 'sysfs', and that is because there is still a sysfs file for use by
userspace when the compositor doesn't support this property.
If usespace has not modified this property, the default value will
be for sysfs to control it. Once userspace has set the property stop
allowing sysfs control.
The property is only attached to non-OLED eDP panels.
Cc: Xaver Hugl <xaver.hugl@kde.org> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Fix pointer casts when reading dynamic region sizes
The function amdgpu_virt_get_dynamic_data_info() writes a 64-bit size
value. In two places (amdgpu_bios.c and amdgpu_discovery.c), the code
passed the address of a smaller variable by casting it to u64 *, which
is unsafe.
This could make the function write more bytes than the smaller variable
can hold, possibly overwriting nearby memory. Reported by static
analysis tools.
v2: Dynamic region size comes from the host (SR-IOV setup) and is always
fixed to 5 MB. (Lijo/Ellen)
5 MB easily fits inside a 32-bit value, so using a 64-bit type is not
needed. It also avoids extra type casts
Fixes: b4a8fcc7826a ("drm/amdgpu: Add logic for VF ipd and VF bios to init from dynamic crit_region offsets")
Reported by: Dan Carpenter <dan.carpenter@linaro.org> Cc: Ellen Pan <yunru.pan@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Make SR-IOV critical region checks overflow-safe
The function amdgpu_virt_init_critical_region() contained an invalid
check for a negative init_hdr_offset value:
if (init_hdr_offset < 0)
Since init_hdr_offset is an unsigned 32-bit integer, this condition can
never be true and triggers a Smatch warning:
warn: unsigned 'init_hdr_offset' is never less than zero
In addition, the subsequent bounds check: if ((init_hdr_offset +
init_hdr_size) > vram_size) was vulnerable to integer overflow when
adding the two unsigned values. Thus, by promoting offset and size to
64-bit and using check_add_overflow() to safely validate the sum against
VRAM size.
Fixes: 07009df6494d ("drm/amdgpu: Introduce SRIOV critical regions v2 during VF init")
Reported by: Dan Carpenter <dan.carpenter@linaro.org> Cc: Ellen Pan <yunru.pan@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Ellen Pan <yunru.pan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 22 Oct 2025 13:19:55 +0000 (09:19 -0400)]
drm/amdgpu: fix SPDX header on cyan_skillfish_reg_init.c
This should be MIT. The driver in general is MIT and
the license text at the top of the file is MIT so fix
it.
Fixes: e8529dbc75ca ("drm/amdgpu: add ip offset support for cyan skillfish") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4654 Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dan Carpenter [Wed, 22 Oct 2025 11:03:24 +0000 (14:03 +0300)]
drm/amdgpu/userqueue: Fix use after free in amdgpu_userq_buffer_vas_list_cleanup()
The amdgpu_userq_buffer_va_list_del() function frees "va_cursor" but it
is dereferenced on the next line when we print the debug message. Print
the debug message first and then free it.
Fixes: 2a28f9665dca ("drm/amdgpu: track the userq bo va for its obj management") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
John Smith [Tue, 21 Oct 2025 09:09:09 +0000 (11:09 +0200)]
drm/amd/pm/powerplay/smumgr: Fix PCIeBootLinkLevel value on Iceland
Previously this was initialized with zero which represented PCIe Gen
1.0 instead of using the
maximum value from the speed table which is the behaviour of all other
smumgr implementations.
Fixes: 18aafc59b106 ("drm/amd/powerplay: implement fw related smu interface for iceland.") Signed-off-by: John Smith <itistotalbotnet@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
John Smith [Tue, 21 Oct 2025 09:08:13 +0000 (11:08 +0200)]
drm/amd/pm/powerplay/smumgr: Fix PCIeBootLinkLevel value on Fiji
Previously this was initialized with zero which represented PCIe Gen
1.0 instead of using the
maximum value from the speed table which is the behaviour of all other
smumgr implementations.
Fixes: 18edef19ea44 ("drm/amd/powerplay: implement fw image related smu interface for Fiji.") Signed-off-by: John Smith <itistotalbotnet@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yang Wang [Wed, 22 Oct 2025 06:12:21 +0000 (14:12 +0800)]
drm/amd/pm: fix smu table id bound check issue in smu_cmn_update_table()
'table_index' is a variable defined by the smu driver (kmd)
'table_id' is a variable defined by the hw smu (pmfw)
This code should use table_index as a bounds check.
Fixes: caad2613dc4bd ("drm/amd/powerplay: move table setting common code to smu_cmn.c") Signed-off-by: Yang Wang <kevinyang.wang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Matthew Schwartz [Mon, 20 Oct 2025 23:09:34 +0000 (16:09 -0700)]
drm/amd/display: Don't program BLNDGAM_MEM_PWR_FORCE when CM low-power is disabled on DCN30
Before commit 33056a97ae5e ("drm/amd/display: Remove double checks for
`debug.enable_mem_low_power.bits.cm`"), dpp3_program_blnd_lut(NULL)
checked the low-power debug flag before calling
dpp3_power_on_blnd_lut(false).
After commit 33056a97ae5e ("drm/amd/display: Remove double checks for
`debug.enable_mem_low_power.bits.cm`"), dpp3_program_blnd_lut(NULL)
unconditionally calls dpp3_power_on_blnd_lut(false). The BLNDGAM power
helper writes BLNDGAM_MEM_PWR_FORCE when CM low-power is disabled, causing
immediate SRAM power toggles instead of deferring at vupdate. This can
disrupt atomic color/LUT sequencing during transitions between
direct scanout and composition within gamescope's DRM backend on
Steam Deck OLED.
To fix this, leave the BLNDGAM power state unchanged when low-power is
disabled, matching dpp3_power_on_hdr3dlut and dpp3_power_on_shaper.
Fixes: 33056a97ae5e ("drm/amd/display: Remove double checks for `debug.enable_mem_low_power.bits.cm`") Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Perry Yuan [Tue, 14 Oct 2025 07:05:19 +0000 (15:05 +0800)]
drm/amdgpu: get rev_id from strap register or IP-discovery table
Query the sub-revision field in the IP Discovery table for the VFs
to obtain their revision ID.
Meanwhile, read the revision ID from the strap register for the PF.
Signed-off-by: Perry Yuan <perry.yuan@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kenneth Feng [Fri, 28 Mar 2025 02:34:57 +0000 (10:34 +0800)]
drm/amd/display: pause the workload setting in dm
v1:
Pause the workload setting in dm when doinn idle optimization
v2:
Rebase patch to latest kernel code base (kernel 6.16)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel Palmer [Sat, 18 Oct 2025 05:44:51 +0000 (14:44 +0900)]
drm/radeon: Remove calls to drm_put_dev()
Since the allocation of the drivers main structure was changed to
devm_drm_dev_alloc() drm_put_dev()'ing to trigger it to be free'd
should be done by devres.
However, drm_put_dev() is still in the probe error and device remove
paths. When the driver fails to probe warnings like the following are
shown because devres is trying to drm_put_dev() after the driver
already did it.
[ 5.642230] radeon 0000:01:05.0: probe with driver radeon failed with error -22
[ 5.649605] ------------[ cut here ]------------
[ 5.649607] refcount_t: underflow; use-after-free.
[ 5.649620] WARNING: CPU: 0 PID: 357 at lib/refcount.c:28 refcount_warn_saturate+0xbe/0x110
Fixes: a9ed2f052c5c ("drm/radeon: change drm_dev_alloc to devm_drm_dev_alloc") Signed-off-by: Daniel Palmer <daniel@0x0f.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel Palmer [Sat, 18 Oct 2025 05:44:50 +0000 (14:44 +0900)]
drm/radeon: Do not kfree() devres managed rdev
Since the allocation of the drivers main structure was changed to
devm_drm_dev_alloc() rdev is managed by devres and we shouldn't be calling
kfree() on it.
This fixes things exploding if the driver probe fails and devres cleans up
the rdev after we already free'd it.
Fixes: a9ed2f052c5c ("drm/radeon: change drm_dev_alloc to devm_drm_dev_alloc") Signed-off-by: Daniel Palmer <daniel@0x0f.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd: Check that VPE has reached DPM0 in idle handler
[Why]
Newer VPE microcode has functionality that will decrease DPM level
only when a workload has run for 2 or more seconds. If VPE is turned
off before this DPM decrease and the PMFW doesn't reset it when
power gating VPE, the SOC can get stuck with a higher DPM level.
This can happen from amdgpu's ring buffer test because it's a short
quick workload for VPE and VPE is turned off after 1s.
[How]
In idle handler besides checking fences are drained check PMFW version
to determine if it will reset DPM when power gating VPE. If PMFW will
not do this, then check VPE DPM level. If it is not DPM0 reschedule
delayed work again until it is.
v2: squash in return fix (Alex)
Cc: Peyton.Lee@amd.com Reported-by: Sultan Alsawaf <sultan@kerneltoast.com> Reviewed-by: Sultan Alsawaf <sultan@kerneltoast.com> Tested-by: Sultan Alsawaf <sultan@kerneltoast.com> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4615 Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Icenowy Zheng [Mon, 20 Oct 2025 05:35:23 +0000 (13:35 +0800)]
drm/ttm: add pgprot handling for RISC-V
The RISC-V Svpbmt privileged extension provides support for overriding
page memory coherency attributes, and, along with vendor extensions like
Xtheadmae, supports pgprot_{writecombine,noncached} on RISC-V.
Adapt the codepath that maps ttm_write_combined to pgprot_writecombine
and ttm_noncached to pgprot_noncached to RISC-V, to allow proper page
access attributes.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me> Tested-by: Han Gao <rabenda.cn@gmail.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20251020053523.731353-1-uwu@icenowy.me
projects / thirdparty / linux.git / log
