David Yang [Mon, 1 Dec 2025 09:42:28 +0000 (17:42 +0800)]
net: dsa: yt921x: Use *_ULL bitfield macros for VLAN_CTRL
VLAN_CTRL should be treated as a 64-bit register. GENMASK and BIT
macros use unsigned long as the underlying type, which will result in a
build error on architectures where sizeof(long) == 4.
====================
Add SQI and SQI+ support for OATC14 10Base-T1S PHYs and Microchip T1S driver
This patch series adds Signal Quality Indicator (SQI) and enhanced SQI+
support for OATC14 10Base-T1S PHYs, along with integration into the
Microchip T1S PHY driver. This enables ethtool to report the SQI value for
OATC14 10Base-T1S PHYs.
====================
net: phy: phy-c45: add SQI and SQI+ support for OATC14 10Base-T1S PHYs
Add support for reading Signal Quality Indicator (SQI) and enhanced SQI+
from OATC14 10Base-T1S PHYs.
- Introduce MDIO register definitions for DCQ_SQI and DCQ_SQIPLUS.
- Add `genphy_c45_oatc14_get_sqi_max()` to return the maximum supported
SQI/SQI+ level.
- Add `genphy_c45_oatc14_get_sqi()` to return the current SQI or SQI+
value.
- Update `include/linux/phy.h` to expose the new APIs.
SQI+ capability is read from the Advanced Diagnostic Features Capability
register (ADFCAP). If SQI+ is supported, the driver calculates the value
from the MSBs of the DCQ_SQIPLUS register; otherwise, it falls back to
basic SQI (0-7 levels). This enables ethtool to report the SQI value for
OATC14 10Base-T1S PHYs.
Open Alliance TC14 10BASE-T1S Advanced Diagnostic PHY Features
Specification ref:
https://opensig.org/wp-content/uploads/2025/06/OPEN_Alliance_10BASE-T1S_Advanced_PHY_features_for-automotive_Ethernet_V2.1b.pdf
Gal Pressman [Sun, 30 Nov 2025 10:25:34 +0000 (12:25 +0200)]
net/mlx5e: Use standard unit definitions for bandwidth conversion
MLX5E_100MB and MLX5E_1GB defines are confusing, MLX5E_100MB is not
equal to 100 * MEGA, and MLX5E_1GB is not equal to one GIGA, as they
hide the Kbps rate conversion required for ieee_maxrate.
Replace hardcoded bandwidth conversion values with standard unit
definitions from linux/units.h. Rename MLX5E_100MB/MLX5E_1GB to
MLX5E_100MB_TO_KB/MLX5E_1GB_TO_KB to clarify these are conversion
factors to Kbps, not absolute bandwidth values.
====================
net: dsa: b53: fix ARL accesses for BCM5325/65 and allow VID 0
ARL entries on BCM5325 and BCM5365 were broken significantly in two
ways:
- Entries for the CPU port were using the wrong port id, pointing to a
non existing port.
- Setting the VLAN ID for entries was not done, adding them all to VLAN
0 instead.
While the former technically broke any communication to the CPU port,
with the latter they were added to the currently unused VID 0, so they
never became effective. Presumably the default PVID was set to 1 because
of these issues 0 was broken (and the root cause not found).
So fix writing and reading entries on BCM5325/65 by first fixing the CPU
port entries, then fixing setting the VLAN ID for entries.
Finally, re-allow VID 0 for BCM5325/65 to allow the whole 1-15 VLAN ID
range to be available to users, and align VLAN handling with all other
switch chips.
====================
Jonas Gorski [Fri, 28 Nov 2025 08:06:25 +0000 (09:06 +0100)]
net: dsa: b53: allow VID 0 for BCM5325/65
Now that writing ARL entries works properly, we can actually use VID 0
as the default untagged VLAN for BCM5325 and BCM5365 as well.
So use 0 as default PVID for all chips and do not reject VLAN 0 anymore,
which we ignored since commit 45e9d59d3950 ("net: dsa: b53: do not allow
to configure VLAN 0") anyway.
Jonas Gorski [Fri, 28 Nov 2025 08:06:24 +0000 (09:06 +0100)]
net: dsa: b53: fix BCM5325/65 ARL entry VIDs
BCM5325/65's ARL entry registers do not contain the VID, only the search
result register does. ARL entries have a separate VID entry register for
the index into the VLAN table.
So make ARL entry accessors use the VID entry registers instead, and
move the VLAN ID field definition to the search register definition.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20251128080625.27181-7-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Gorski [Fri, 28 Nov 2025 08:06:23 +0000 (09:06 +0100)]
net: dsa: b53: fix BCM5325/65 ARL entry multicast port masks
We currently use the mask 0xf for writing and reading b53_entry::port,
but this is only correct for unicast ARL entries. Multicast ARL entries
use a bitmask, and 0xf is not enough space for ports > 3, which includes
the CPU port.
So extend the mask accordingly to also fit port 4 (bit 4) and MII (bit
5). According to the datasheet the multicast port mask is [60:48],
making it 12 bit wide, but bits 60-55 are reserved anyway, and collide
with the priority field at [60:59], so I am not sure if this is valid.
Therefore leave it at the actual used range, [53:48].
The ARL search result register differs a bit, and there the mask is only
[52:48], so only spanning the user ports. The MII port bit is
contained in the Search Result Extension register. So create a separate
search result parse function that properly handles this.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365") Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Link: https://patch.msgid.link/20251128080625.27181-6-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Gorski [Fri, 28 Nov 2025 08:06:22 +0000 (09:06 +0100)]
net: dsa: b53: fix CPU port unicast ARL entries for BCM5325/65
On BCM5325 and BCM5365, unicast ARL entries use 8 as the value for the
CPU port, so we need to translate it to/from 5 as used for the CPU port
at most other places.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20251128080625.27181-5-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Gorski [Fri, 28 Nov 2025 08:06:21 +0000 (09:06 +0100)]
net: dsa: b53: use same ARL search result offset for BCM5325/65
BCM5365's search result is at the same offset as BCM5325's search
result, and they (mostly) share the same format, so switch BCM5365 to
BCM5325's arl ops.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365") Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Tested-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Link: https://patch.msgid.link/20251128080625.27181-4-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
amd-xgbe: schedule NAPI on RBU event
During the RX overload the Rx buffers may not be refilled, trying to
schedule the NAPI when an Rx Buffer Unavailable is signaled may help in
improving the such situation, in case we missed an IRQ.
====================
Raju Rangoju [Sat, 29 Nov 2025 17:50:16 +0000 (23:20 +0530)]
amd-xgbe: schedule NAPI on Rx Buffer Unavailable (RBU)
Under heavy load, Rx Buffer Unavailable (RBU) can occur if Rx processing
is slower than network. When an RBU is signaled, try to schedule NAPI to
help recover from such situation (including cases where an IRQ may be
missed or such)
Long Li [Wed, 26 Nov 2025 21:45:52 +0000 (13:45 -0800)]
net: mana: Handle hardware recovery events when probing the device
When MANA is being probed, it's possible that hardware is in recovery
mode and the device may get GDMA_EQE_HWC_RESET_REQUEST over HWC in the
middle of the probe. Detect such condition and go through the recovery
service procedure.
Jeremy Kerr [Wed, 26 Nov 2025 08:48:54 +0000 (16:48 +0800)]
net: mctp: test: move TX packetqueue from dst to dev
To capture TX packets during a test, we are currently intercepting the
dst->output with an implementation that adds the transmitted packet to
a skb queue attached to the test-specific mock dst. The netdev itself is
not involved in the test TX path.
Instead, we can just use our test device to stash TXed packets for later
inspection by the test. This means we can include the actual
mctp_dst_output() implementation in the test (by setting dst.output in
the test case), and don't need to be creating fake dst objects, or their
corresponding skb queues.
We need to ensure that the netdev is up to allow delivery to
ndo_start_xmit, but the tests assume active devices at present anyway.
Vladimir Oltean [Tue, 25 Nov 2025 10:35:07 +0000 (12:35 +0200)]
net: pcs: lynx: accept in-band autoneg for 2500base-x
Testing in two circumstances:
1. back to back optical SFP+ connection between two LS1028A-QDS ports
with the SCH-26908 riser card
2. T1042 with on-board AQR115 PHY using "OCSGMII", as per
https://lore.kernel.org/lkml/aIuEvaSCIQdJWcZx@FUE-ALEWI-WINX/
strongly suggests that enabling in-band auto-negotiation is actually
possible when the lane baud rate is 3.125 Gbps.
It was previously thought that this would not be the case, because it
was only tested on 2500base-x links with on-board Aquantia PHYs, where
it was noticed that MII_LPA is always reported as zero, and it was
thought that this is because of the PCS.
Test case #1 above shows it is not, and the configured MII_ADVERTISE on
system A ends up in the MII_LPA on system B, when in 2500base-x mode
(IF_MODE=0).
Test case #2, which uses "SGMII" auto-negotiation (IF_MODE=3) for the
3.125 Gbps lane, is actually a misconfiguration, but it is what led to
the discovery.
There is actually an old bug in the Lynx PCS driver - it expects all
register values to contain their default out-of-reset values, as if the
PCS were initialized by the Reset Configuration Word (RCW) settings.
There are 2 cases in which this is problematic:
- if the bootloader (or previous kexec-enabled Linux) wrote a different
IF_MODE value
- if dynamically changing the SerDes protocol from 1000base-x to
2500base-x, e.g. by replacing the optical SFP module.
Specifically in test case #2, an accidental alignment between the
bootloader configuring the PCS to expect SGMII in-band code words, and
the AQR115 PHY actually transmitting SGMII in-band code words when
operating in the "OCSGMII" system interface protocol, led to the PCS
transmitting replicated symbols at 3.125 Gbps baud rate. This could only
have happened if the PCS saw and reacted to the SGMII code words in the
first place.
Since test #2 is invalid from a protocol perspective (there seems to be
no standard way of negotiating the data rate of 2500 Mbps with SGMII,
and the lower data rates should remain 10/100/1000), in-band auto-negotiation
for 2500base-x effectively means Clause 37 (i.e. IF_MODE=0).
Make 2500base-x be treated like 1000base-x in this regard, by removing
all prior limitations and calling lynx_pcs_config_giga().
This adds a new feature: LINK_INBAND_ENABLE and at the same time fixes
the Lynx PCS's long standing problem that the registers (specifically
IF_MODE, but others could be misconfigured as well) are not written by
the driver to the known valid values for 2500base-x.
Co-developed-by: Alexander Wilhelm <alexander.wilhelm@westermo.com> Signed-off-by: Alexander Wilhelm <alexander.wilhelm@westermo.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20251125103507.749654-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andre Carvalho [Sat, 29 Nov 2025 12:24:19 +0000 (12:24 +0000)]
selftests: netconsole: remove log noise due to socat exit
This removes some noise that can be distracting while looking at
selftests by redirecting socat stderr to /dev/null.
Before this commit, netcons_basic would output:
Running with target mode: basic (ipv6)
2025/11/29 12:08:03 socat[259] W exiting on signal 15
2025/11/29 12:08:03 socat[271] W exiting on signal 15
basic : ipv6 : Test passed
Running with target mode: basic (ipv4)
2025/11/29 12:08:05 socat[329] W exiting on signal 15
2025/11/29 12:08:05 socat[322] W exiting on signal 15
basic : ipv4 : Test passed
Running with target mode: extended (ipv6)
2025/11/29 12:08:08 socat[386] W exiting on signal 15
2025/11/29 12:08:08 socat[386] W exiting on signal 15
2025/11/29 12:08:08 socat[380] W exiting on signal 15
extended : ipv6 : Test passed
Running with target mode: extended (ipv4)
2025/11/29 12:08:10 socat[440] W exiting on signal 15
2025/11/29 12:08:10 socat[435] W exiting on signal 15
2025/11/29 12:08:10 socat[435] W exiting on signal 15
extended : ipv4 : Test passed
After these changes, output looks like:
Running with target mode: basic (ipv6)
basic : ipv6 : Test passed
Running with target mode: basic (ipv4)
basic : ipv4 : Test passed
Running with target mode: extended (ipv6)
extended : ipv6 : Test passed
Running with target mode: extended (ipv4)
extended : ipv4 : Test passed
Alok Tiwari [Fri, 28 Nov 2025 08:52:57 +0000 (00:52 -0800)]
l2tp: correct debugfs label for tunnel tx stats
l2tp_dfs_seq_tunnel_show prints two groups of tunnel statistics. The
first group reports transmit counters, but the code labels it as rx.
Set the label to "tx" so the debugfs output reflects the actual meaning.
Jakub Kicinski [Thu, 27 Nov 2025 19:45:56 +0000 (11:45 -0800)]
selftests: net: add a hint about MACAddressPolicy=persistent
New NIPA installation had been reporting a few flaky tests.
arp_ndisc_evict_nocarrier is most flaky of them all.
I suspect that the flakiness is due to udev swapping the MAC
addresses on the interfaces. Extend the message in
arp_ndisc_evict_nocarrier to hint at this potential issue.
Having the neigh get fail right after ping is rather unusual,
unless udev changes the MAC addr causing a flush in the meantime.
Jakub Kicinski [Fri, 28 Nov 2025 00:48:46 +0000 (16:48 -0800)]
selftests: net: py: handle interrupt during cleanup
Following up on the old discussion [1]. Let the BaseExceptions out of
defer()'ed cleanup. And handle it in the main loop. This allows us to
exit the tests if user hit Ctrl-C during defer().
====================
net: freescale: migrate to .get_rx_ring_count() ethtool callback
This series migrates Freescale network drivers to use the new .get_rx_ring_count()
ethtool callback introduced in commit 84eaf4359c36 ("net: ethtool: add
get_rx_ring_count callback to optimize RX ring queries").
The new callback simplifies the .get_rxnfc() implementation by removing
ETHTOOL_GRXRINGS handling and moving it to a dedicated callback. This provides
a cleaner separation of concerns and aligns these drivers with the modern
ethtool API.
The series updates the following Freescale drivers:
- enetc
- dppa2
- gianfar
====================
Breno Leitao [Fri, 28 Nov 2025 13:11:47 +0000 (05:11 -0800)]
net: enetc: convert to use .get_rx_ring_count
Convert the enetc driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc for handling
ETHTOOL_GRXRINGS command. This simplifies the code in two ways:
1. For enetc_get_rxnfc(): Remove the ETHTOOL_GRXRINGS case from the
switch statement while keeping other cases for classifier rules.
2. For enetc4_get_rxnfc(): Remove it completely and use
enetc_get_rxnfc() instead.
Now on, enetc_get_rx_ring_count() is the callback that returns the
number of RX rings for enetc driver.
Also, remove the documentation around enetc4_get_rxnfc(), which was not
matching what the function did(?!).
Breno Leitao [Fri, 28 Nov 2025 13:11:46 +0000 (05:11 -0800)]
net: dpaa2: convert to use .get_rx_ring_count
Convert the dpaa2 driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc for handling
ETHTOOL_GRXRINGS command. This simplifies the code by removing the
ETHTOOL_GRXRINGS case from the switch statement and replacing it with
a direct return of the queue count.
The driver still maintains .get_rxnfc for other commands including
ETHTOOL_GRXCLSRLCNT, ETHTOOL_GRXCLSRULE, and ETHTOOL_GRXCLSRLALL.
Breno Leitao [Fri, 28 Nov 2025 13:11:45 +0000 (05:11 -0800)]
net: gianfar: convert to use .get_rx_ring_count
Convert the gianfar driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc for handling
ETHTOOL_GRXRINGS command. This simplifies the code by removing the
ETHTOOL_GRXRINGS case from the switch statement and replacing it with
a direct return of the queue count.
The driver still maintains .get_rxnfc for other commands including
ETHTOOL_GRXCLSRLCNT, ETHTOOL_GRXCLSRULE, and ETHTOOL_GRXCLSRLALL.
The patch is by Oliver Hartkopp and fixes the compilation of the
CAN_RAW protocol if the CAN driver infrastructure is not enabled.
This problem was introduced in the current development cycle of
net-next.
* tag 'linux-can-next-for-6.19-20251129' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: Kconfig: select CAN driver infrastructure by default
====================
Oliver Hartkopp [Sat, 29 Nov 2025 09:05:00 +0000 (10:05 +0100)]
can: Kconfig: select CAN driver infrastructure by default
The CAN bus support enabled with CONFIG_CAN provides a socket-based
access to CAN interfaces. With the introduction of the latest CAN protocol
CAN XL additional configuration status information needs to be exposed to
the network layer than formerly provided by standard Linux network drivers.
This requires the CAN driver infrastructure to be selected by default.
As the CAN network layer can only operate on CAN interfaces anyway all
distributions and common default configs enable at least one CAN driver.
So selecting CONFIG_CAN_DEV when CONFIG_CAN is selected by the user has
no effect on established configurations but solves potential build issues
when CONFIG_CAN[_XXX]=y is set together with CANFIG_CAN_DEV=m
Fixes: 1a620a723853 ("can: raw: instantly reject unsupported CAN frames") Reported-by: Vincent Mailhol <mailhol@kernel.org> Closes: https://lore.kernel.org/all/CAMZ6RqL_nGszwoLPXn1Li8op-ox4k3Hs6p=Hw6+w0W=DTtobPw@mail.gmail.com/ Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202511280531.YnWW2Rxc-lkp@intel.com/ Closes: https://lore.kernel.org/oe-kbuild-all/202511280842.djCQ0N0O-lkp@intel.com/ Closes: https://lore.kernel.org/oe-kbuild-all/202511282325.uVQFRTkA-lkp@intel.com/ Closes: https://lore.kernel.org/oe-kbuild-all/202511291520.guIE1QHj-lkp@intel.com/ Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://patch.msgid.link/20251129090500.17484-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Thorsten Blum [Wed, 26 Nov 2025 22:08:05 +0000 (23:08 +0100)]
net: ipconfig: Replace strncpy with strscpy in ic_proto_name
strncpy() is deprecated [1] for NUL-terminated destination buffers
because it does not guarantee NUL termination. Replace it with strscpy()
to ensure the destination buffer is always NUL-terminated and to avoid
any additional NUL padding.
Although the identifier buffer has 252 usable bytes, strncpy() copied
only up to 251 bytes to the zero-initialized buffer, relying on the last
byte to act as an implicit NUL terminator. Switching to strscpy() avoids
this implicit behavior and does not use magic numbers.
The source string is also NUL-terminated and satisfies the
__must_be_cstr() requirement of strscpy().
Jakub Kicinski [Sat, 29 Nov 2025 04:08:39 +0000 (20:08 -0800)]
Merge tag 'nf-next-25-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains Netfilter updates for net-next:
0) Add sanity check for maximum encapsulations in bridge vlan,
reported by the new AI robot.
1) Move the flowtable path discovery code to its own file, the
nft_flow_offload.c mixes the nf_tables evaluation with the path
discovery logic, just split this in two for clarity.
2) Consolidate flowtable xmit path by using dev_queue_xmit() and the
real device behind the layer 2 vlan/pppoe device. This allows to
inline encapsulation. After this update, hw_ifidx can be removed
since both ifidx and hw_ifidx now point to the same device.
3) Support for IPIP encapsulation in the flowtable, extend selftest
to cover for this new layer 3 offload, from Lorenzo Bianconi.
4) Push down the skb into the conncount API to fix duplicates in the
conncount list for packets with non-confirmed conntrack entries,
this is due to an optimization introduced in d265929930e2
("netfilter: nf_conncount: reduce unnecessary GC").
From Fernando Fernandez Mancera.
5) In conncount, disable BH when performing garbage collection
to consolidate existing behaviour in the conncount API, also
from Fernando.
6) A matching packet with a confirmed conntrack invokes GC if
conncount reaches the limit in an attempt to release slots.
This allows the existing extensions to be used for real conntrack
counting, not just limiting new connections, from Fernando.
7) Support for updating ct count objects in nf_tables, from Fernando.
8) Extend nft_flowtables.sh selftest to send IPv6 TCP traffic,
from Lorenzo Bianconi.
9) Fixes for UAPI kernel-doc documentation, from Randy Dunlap.
* tag 'nf-next-25-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_tables: improve UAPI kernel-doc comments
netfilter: ip6t_srh: fix UAPI kernel-doc comments format
selftests: netfilter: nft_flowtable.sh: Add the capability to send IPv6 TCP traffic
netfilter: nft_connlimit: add support to object update operation
netfilter: nft_connlimit: update the count if add was skipped
netfilter: nf_conncount: make nf_conncount_gc_list() to disable BH
netfilter: nf_conncount: rework API to use sk_buff directly
selftests: netfilter: nft_flowtable.sh: Add IPIP flowtable selftest
netfilter: flowtable: Add IPIP tx sw acceleration
netfilter: flowtable: Add IPIP rx sw acceleration
netfilter: flowtable: use tuple address to calculate next hop
netfilter: flowtable: remove hw_ifidx
netfilter: flowtable: inline pppoe encapsulation in xmit path
netfilter: flowtable: inline vlan encapsulation in xmit path
netfilter: flowtable: consolidate xmit path
netfilter: flowtable: move path discovery infrastructure to its own file
netfilter: flowtable: check for maximum number of encapsulations in bridge vlan
====================
====================
Introduce the dsa_xmit_port_mask() tagging protocol helper
What
----
Some DSA tags have just the port number in the TX header format, others
have a bit field where in theory, multiple bits can be set, even though
DSA only sets one.
The latter kind is now making use of a dsa_xmit_port_mask() helper,
which will decide when to set more than 1 bit in that mask.
Why
---
David Yang has pointed out in a recently posted patch that HSR packet
duplication on transmission can be offloaded even on HSR-unaware
switches. This should be made generally available to all DSA switches.
How to test
-----------
These patches just lay the groundwork, and there should be no functional
change - so for this set, regression testing is all that's necessary.
For testing the HSR packet duplication idea, I've put together a branch:
https://github.com/vladimiroltean/linux/commits/dsa-simple-hsr-offload/
where most drivers are patched to call dsa_port_simple_hsr_join() and
dsa_port_simple_hsr_leave().
Assuming there are volunteers to also test the latter, one can enable
CONFIG_HSR and create a HSR device using:
$ ip link add name hsr0 type hsr slave1 swp0 slave2 swp1 supervision 45 version 1
This needs to be connected using 2 cables to another system where the
same command was run. Then, one should be able to ping the other board
through the hsr0 interface.
Without the Github branch, a ping over HSR should increase the DSA
conduit interface's TX counters by 2 packets. With the Github branch,
the TX counters should increase by only 1 packet.
Why so many patches
-------------------
To avoid the situation where a patch has to be backported, conflicts
with the work done here, pulls this in as a dependency, and that pulls
in 13 other unrelated drivers. These don't have any dependencies between
each other and can be cherry-picked at will (except they all depend on
patch 1/15).
====================
Vladimir Oltean [Thu, 27 Nov 2025 12:09:02 +0000 (14:09 +0200)]
net: dsa: tag_yt921x: use the dsa_xmit_port_mask() helper
The "yt921x" tagging protocol populates a bit mask for the TX ports,
so we can use dsa_xmit_port_mask() to centralize the decision of how to
set that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:09:01 +0000 (14:09 +0200)]
net: dsa: tag_xrs700x: use the dsa_xmit_port_mask() helper
The "xrs700x" is the original DSA tagging protocol with HSR TX
replication support, we now essentially move that logic to the
dsa_xmit_port_mask() helper. The end result is something akin to
hellcreek_xmit() (but reminds me I should also take care of
skb_checksum_help() for tail taggers in the core).
The implementation differences to dsa_xmit_port_mask() are immaterial.
Vladimir Oltean [Thu, 27 Nov 2025 12:09:00 +0000 (14:09 +0200)]
net: dsa: tag_trailer: use the dsa_xmit_port_mask() helper
The "trailer" tagging protocol populates a bit mask for the TX ports, so
we can use dsa_xmit_port_mask() to centralize the decision of how to set
that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:59 +0000 (14:08 +0200)]
net: dsa: tag_rzn1_a5psw: use the dsa_xmit_port_mask() helper
The "a5psw" tagging protocol populates a bit mask for the TX ports,
so we can use dsa_xmit_port_mask() to centralize the decision of how to
set that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:58 +0000 (14:08 +0200)]
net: dsa: tag_rtl8_4: use the dsa_xmit_port_mask() helper
The "rtl8_4" and "rtl8_4t" tagging protocols populate a bit mask for the
TX ports, so we can use dsa_xmit_port_mask() to centralize the decision
of how to set that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:57 +0000 (14:08 +0200)]
net: dsa: tag_rtl4_a: use the dsa_xmit_port_mask() helper
The "rtl4a" tagging protocol populates a bit mask for the TX ports,
so we can use dsa_xmit_port_mask() to centralize the decision of how to
set that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:56 +0000 (14:08 +0200)]
net: dsa: tag_qca: use the dsa_xmit_port_mask() helper
The "qca" tagging protocol populates a bit mask for the TX ports, so we
can use dsa_xmit_port_mask() to centralize the decision of how to set
that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:55 +0000 (14:08 +0200)]
net: dsa: tag_ocelot: use the dsa_xmit_port_mask() helper
The "ocelot" and "seville" tagging protocols populate a bit mask for the
TX ports, so we can use dsa_xmit_port_mask() to centralize the decision
of how to set that field.
This protocol used BIT_ULL() rather than simple BIT() to silence Smatch,
as explained in commit 1f778d500df3 ("net: mscc: ocelot: avoid type
promotion when calling ocelot_ifh_set_dest"). I would expect that this
tool no longer complains now, when the BIT(dp->index) is hidden inside
the dsa_xmit_port_mask() function, the return value of which is promoted
to u64.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:54 +0000 (14:08 +0200)]
net: dsa: tag_mxl_gsw1xx: use the dsa_xmit_port_mask() helper
The "gsw1xx" tagging protocol populates a bit mask for the TX ports, so
we can use dsa_xmit_port_mask() to centralize the decision of how to set
that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:53 +0000 (14:08 +0200)]
net: dsa: tag_mtk: use the dsa_xmit_port_mask() helper
The "mtk" tagging protocol populates a bit mask for the TX ports, so we
can use dsa_xmit_port_mask() to centralize the decision of how to set
that field.
Cc: Chester A. Unal" <chester.a.unal@arinc9.com> Cc: Daniel Golle <daniel@makrotopia.org> Cc: DENG Qingfang <dqfext@gmail.com> Cc: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20251127120902.292555-7-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Thu, 27 Nov 2025 12:08:51 +0000 (14:08 +0200)]
net: dsa: tag_hellcreek: use the dsa_xmit_port_mask() helper
The "hellcreek" tagging protocol populates a bit mask for the TX ports,
so we can use dsa_xmit_port_mask() to centralize the decision of how to
set that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:50 +0000 (14:08 +0200)]
net: dsa: tag_gswip: use the dsa_xmit_port_mask() helper
The "gswip" tagging protocol populates a bit mask for the TX ports, so
we can use dsa_xmit_port_mask() to centralize the decision of how to set
that field.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:49 +0000 (14:08 +0200)]
net: dsa: tag_brcm: use the dsa_xmit_port_mask() helper
The "brcm" and "brcm-prepend" tagging protocols populate a bit mask for
the TX ports, so we can use dsa_xmit_port_mask() to centralize the
decision of how to set that field. The port mask is written u8 by u8,
first the high octet and then the low octet.
Vladimir Oltean [Thu, 27 Nov 2025 12:08:48 +0000 (14:08 +0200)]
net: dsa: introduce the dsa_xmit_port_mask() tagging protocol helper
Many tagging protocols deal with the transmit port mask being a bit
mask, and set it to BIT(dp->index). Not a big deal.
Also, some tagging protocols are written for switches which support HSR
offload (including packet duplication offload), there we see a walk
using dsa_hsr_foreach_port() to find the other port in the same switch
that's member of the HSR, and set that bit in the port mask too.
That isn't sufficiently interesting either, until you come to realize
that there isn't anything special in the second case that switches just
in the first one can't do too.
It just becomes a matter of "is it wise to do it? are sufficient people
using HSR/PRP with generic off-the-shelf switches to justify add an
extra test in the data path?" - the answer to which is probably "it
depends". It isn't _much_ worse to not have HSR offload at all, so as to
make it impractical, esp. with a rich OS like Linux. But the HSR users
are rather specialized in industrial networking.
Anyway, the change acts on the premise that we're going to have support
for this, it should be uniformly implemented for everyone, and that if
we find some sort of balance, we can keep everyone relatively happy.
So I've disabled that logic if CONFIG_HSR isn't enabled, and I've tilted
the branch predictor to say it's unlikely we're transmitting through a
port with this capability currently active. On branch miss, we're still
going to save the transmission of one packet, so there's some remaining
benefit there too. I don't _think_ we need to jump to static keys yet.
The helper returns a 32-bit zero-based unsigned number, that callers
have to transpose using FIELD_PREP(). It is not the first time we assume
DSA switches won't be larger than 32 ports - dsa_user_ports() has that
assumption baked into it too.
One last development note about why pass the "skb" argument when this
isn't used. Looking at the compiled code on arm64, which is identical
both with and without it, the answer is "why not?" - who knows what
other features dependent on the skb may be handled in the future.
Link: https://lore.kernel.org/netdev/20251126093240.2853294-4-mmyangfl@gmail.com/ Cc: "Alvin Šipraga" <alsi@bang-olufsen.dk> Cc: Chester A. Unal" <chester.a.unal@arinc9.com> Cc: "Clément Léger" <clement.leger@bootlin.com> Cc: Daniel Golle <daniel@makrotopia.org> Cc: David Yang <mmyangfl@gmail.com> Cc: DENG Qingfang <dqfext@gmail.com> Cc: Florian Fainelli <florian.fainelli@broadcom.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Jonas Gorski <jonas.gorski@gmail.com> Cc: Kurt Kanzenbach <kurt@linutronix.de> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Sean Wang <sean.wang@mediatek.com> Cc: UNGLinuxDriver@microchip.com Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20251127120902.292555-2-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
net: broadcom: migrate to .get_rx_ring_count() ethtool callback
This series migrates Broadcom ethernet drivers to use the new
.get_rx_ring_count() ethtool callback introduced in commit 84eaf4359c36
("net: ethtool: add get_rx_ring_count callback to optimize RX ring
queries").
This change simplifies the .get_rxnfc() implementation by
extracting the ETHTOOL_GRXRINGS case handling into a dedicated callback,
making the code cleaner and aligning these drivers with the updated
ethtool API.
The series covers two Broadcom drivers: bnxt and bcmgenet. Each patch
removes the ETHTOOL_GRXRINGS case from the driver's .get_rxnfc() switch
statement and implements the new .get_rx_ring_count() callback that
returns the number of RX rings.
====================
Breno Leitao [Thu, 27 Nov 2025 10:17:16 +0000 (02:17 -0800)]
net: bcmgenet: extract GRXRINGS from .get_rxnfc
Commit 84eaf4359c36 ("net: ethtool: add get_rx_ring_count callback to
optimize RX ring queries") added specific support for GRXRINGS callback,
simplifying .get_rxnfc.
Remove the handling of GRXRINGS in .get_rxnfc() by moving it to the new
.get_rx_ring_count().
This simplifies the RX ring count retrieval and aligns bcmgenet with the
new ethtool API for querying RX ring parameters.
Breno Leitao [Thu, 27 Nov 2025 10:17:15 +0000 (02:17 -0800)]
net: bnxt: extract GRXRINGS from .get_rxnfc
Commit 84eaf4359c36 ("net: ethtool: add get_rx_ring_count callback to
optimize RX ring queries") added specific support for GRXRINGS callback,
simplifying .get_rxnfc.
Remove the handling of GRXRINGS in .get_rxnfc() by moving it to the new
.get_rx_ring_count().
This simplifies the RX ring count retrieval and aligns bnxt with the new
ethtool API for querying RX ring parameters.
Add schema checking and yaml linting for the YNL specs.
Patch 1 adds a schema_check make target using a pyynl --validate option
Patch 2 adds a lint make target using yamllint
Patches 3,4 fix issues reported by make -C tools/net/ynl lint schema_check
====================
Donald Hunter [Thu, 27 Nov 2025 12:35:00 +0000 (12:35 +0000)]
tools: ynl: add a lint makefile target
Add a lint target to run yamllint on the YNL specs.
make -C tools/net/ynl lint
make: Entering directory '/home/donaldh/net-next/tools/net/ynl'
yamllint ../../../Documentation/netlink/specs/*.yaml
../../../Documentation/netlink/specs/ethtool.yaml
1272:21 warning truthy value should be one of [false, true] (truthy)
Donald Hunter [Thu, 27 Nov 2025 12:34:59 +0000 (12:34 +0000)]
tools: ynl: add schema checking
Add a --validate flag to pyynl for explicit schema check with error
reporting and add a schema_check make target to check all YNL specs.
make -C tools/net/ynl schema_check
make: Entering directory '/home/donaldh/net-next/tools/net/ynl'
ok 1 binder.yaml schema validation
not ok 2 conntrack.yaml schema validation
'labels mask' does not match '^[0-9a-z-]+$'
Failed validating 'pattern' in schema['properties']['attribute-sets']['items']['properties']['attributes']['items']['properties']['name']:
{'type': 'string', 'pattern': '^[0-9a-z-]+$'}
On instance['attribute-sets'][14]['attributes'][22]['name']:
'labels mask'
Jakub Kicinski [Sat, 29 Nov 2025 03:34:20 +0000 (19:34 -0800)]
Merge tag 'wireless-next-2025-11-27' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Apart from the usual small things just driver updates:
- mt76:
- WED support for >32-bit DMA
- airoha NPU support
- regdomain improvements
- continued WiFi7/MLO work
- rtw89
- support USB devices RTL8852AU and RTL8852CU
- initial work for RTL8922DE
- improved injection support
- rtl8xxxu: 40 MHz connection fixes/support
- brcmfmac: Acer A1 840 tablet quirk
* tag 'wireless-next-2025-11-27' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (152 commits)
wifi: mac80211: allow sharing identical chanctx for S1G interfaces
wifi: nl80211: vendor-cmd: intel: fix a blank kernel-doc line warning
wifi: cfg80211: include s1g_primary_2mhz when comparing chandefs
wifi: cfg80211: include s1g_primary_2mhz when sending chandef
wifi: ieee80211: correct FILS status codes
mt76: mt7615: Fix memory leak in mt7615_mcu_wtbl_sta_add()
wifi: mt76: mt792x: fix wifi init fail by setting MCU_RUNNING after CLC load
wifi: mt76: Strip whitespace from build ddate
wifi: mt76: mt7996: Add missing locking in mt7996_mac_sta_rc_work()
wifi: mt76: mt7996: skip ieee80211_iter_keys() on scanning link remove
wifi: mt76: mt7996: skip deflink accounting for offchannel links
wifi: mt76: Move mt76_abort_scan out of mt76_reset_device()
wifi: mt76: mt7996: move mt7996_update_beacons under mt76 mutex
wifi: mt76: mt7996: grab mt76 mutex in mt7996_mac_sta_event()
wifi: mt76: mt7925: ensure the 6GHz A-MPDU density cap from the hardware.
wifi: mt76: mt7996: fix EMI rings for RRO
wifi: mt76: mt7996: fix using wrong phy to start in mt7996_mac_restart()
wifi: mt76: mt7996: fix MLO set key and group key issues
wifi: mt76: mt7996: fix MLD group index assignment
wifi: mt76: mt7996: use correct link_id when filling TXD and TXP
...
====================
Heiko Carstens [Wed, 26 Nov 2025 14:07:05 +0000 (15:07 +0100)]
net: Remove KMSG_COMPONENT macro
The KMSG_COMPONENT macro is a leftover of the s390 specific "kernel message
catalog" from 2008 [1] which never made it upstream.
The macro was added to s390 code to allow for an out-of-tree patch which
used this to generate unique message ids. Also this out-of-tree patch
doesn't exist anymore.
The pattern of how the KMSG_COMPONENT macro is used can also be found at
some non s390 specific code, for whatever reasons. Besides adding an
indirection it is unused.
Remove the macro in order to get rid of a pointless indirection. Replace
all users with the string it defines. In all cases this leads to a simple
replacement like this:
Jakub Kicinski [Fri, 28 Nov 2025 02:59:34 +0000 (18:59 -0800)]
Merge branch 'bnxt_en-updates-for-net-next'
Michael Chan says:
====================
bnxt_en: Updates for net-next (part)
This series includes an enhnacement to the priority TX counters,
an enhancement to a PHY module error extack message, cleanup of
unneeded MSIX logic in bnxt_ulp.c, adding CQ dump during TX timeout,
LRO/HW_GRO performance improvement by enabling Relaxed Ordering,
and improved SRIOV admin link state support.
====================
Rob Miller [Wed, 26 Nov 2025 21:56:47 +0000 (13:56 -0800)]
bnxt_en: Add Virtual Admin Link State Support for VFs
The firmware can now cache the virtual link admin state (auto/on/off) of
all VFs and as such, the PF driver no longer has to intercept the VF
driver's port_phy_qcfg() call and then provide the link admin state.
If the FW does not have this capability, fall back to the existing
interception method.
The initial default link admin state (auto) is also set initially when
the VFs are created.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Mohammad Shuab Siddique <mohammad-shuab.siddique@broadcom.com> Signed-off-by: Rob Miller <rmiller@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20251126215648.1885936-7-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Wed, 26 Nov 2025 21:56:46 +0000 (13:56 -0800)]
bnxt_en: Do not set EOP on RX AGG BDs on 5760X chips
With End-of-Packet padding (EOP) set, the chip will disable Relaxed
Ordering (RO) of TPA data packets. A TPA segment with EOP set will be
padded to the next cache boundary and can potentially overwrite the
beginning bytes of the next TPA segment when RO is enabled on 5760X.
To prevent that, the chip disables RO for TPA when EOP is set.
To take advantge of RO and higher performance, do not set EOP on
5760X chips when TPA is enabled. Define a proper RX_BD_FLAGS_AGG_EOP
constant to make it clear that we are setting EOP.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20251126215648.1885936-6-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kalesh AP [Wed, 26 Nov 2025 21:56:44 +0000 (13:56 -0800)]
bnxt_en: Remove the redundant BNXT_EN_FLAG_MSIX_REQUESTED flag
MSIX is always requested when the RoCE driver calls bnxt_register_dev().
We already check bnxt_ulp_registered(), so checking the flag is
redundant. It was a left-over flag after converting to auxbus, so
remove it.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20251126215648.1885936-4-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Wed, 26 Nov 2025 21:56:42 +0000 (13:56 -0800)]
bnxt_en: Enhance TX pri counters
The priority packet and byte counters in ethtool -S are returned by
the driver based on the pri2cos mapping. The assumption is that each
priority is mapped to one and only one hardware CoS queue. In a
special RoCE configuration, the FW uses combined CoS queue 0 and CoS
queue 1 for the priority mapped to CoS queue 0. In this special
case, we need to add the CoS queue 0 and CoS queue 1 counters for
the priority packet and byte counters.
Natalia cleans up ixgbevf_q_vector struct removing an unused field.
Emil converts vport state tracking from enum to bitmap and removes
unneeded states for idpf.
Tony removes an unneeded check from e1000e.
Alok Tiwari removes an unnecessary second call to
ixgbe_non_sfp_link_config() and adjusts the checked member, in idpf, to
reflect the member that is later used. He also fixes various typos and
messages for better clarity misc Intel drivers.
====================
Alok Tiwari [Tue, 25 Nov 2025 22:36:30 +0000 (14:36 -0800)]
iavf: clarify VLAN add/delete log messages and lower log level
The current dev_warn messages for too many VLAN changes are confusing
and one place incorrectly references "add" instead of "delete" VLANs
due to copy-paste errors.
- Use dev_info instead of dev_warn to lower the log level.
- Rephrase the message to: "virtchnl: Too many VLAN [add|delete]
([v1|v2]) requests; splitting into multiple messages to PF\n".
Suggested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20251125223632.1857532-12-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alok Tiwari [Tue, 25 Nov 2025 22:36:28 +0000 (14:36 -0800)]
idpf: correct queue index in Rx allocation error messages
The error messages in idpf_rx_desc_alloc_all() used the group index i
when reporting memory allocation failures for individual Rx and Rx buffer
queues. This is incorrect.
Update the messages to use the correct queue index j and include the
queue group index i for clearer identification of the affected Rx and Rx
buffer queues.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20251125223632.1857532-10-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alok Tiwari [Tue, 25 Nov 2025 22:36:27 +0000 (14:36 -0800)]
idpf: use desc_ring when checking completion queue DMA allocation
idpf_compl_queue uses a union for comp, comp_4b, and desc_ring. The
release path should check complq->desc_ring to determine whether the DMA
descriptor ring is allocated. The current check against comp works but is
leftover from a previous commit and is misleading in this context.
Switching the check to desc_ring improves readability and more directly
reflects the intended meaning, since desc_ring is the field representing
the allocated DMA-backed descriptor ring.
No functional change.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20251125223632.1857532-9-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alok Tiwari [Tue, 25 Nov 2025 22:36:26 +0000 (14:36 -0800)]
ixgbe: avoid redundant call to ixgbe_non_sfp_link_config()
ixgbe_non_sfp_link_config() is called twice in ixgbe_open()
once to assign its return value to err and again in the
conditional check. This patch uses the stored err value
instead of calling the function a second time. This avoids
redundant work and ensures consistent error reporting.
Also fix a small typo in the ixgbe_remove() comment:
"The could be caused" -> "This could be caused".
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Reviewed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20251125223632.1857532-8-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen [Tue, 25 Nov 2025 22:36:25 +0000 (14:36 -0800)]
e1000e: Remove unneeded checks
The caller, ethtool_set_eeprom(), already performs the same checks so
these are unnecessary in the driver. This reverts commit 90fb7db49c6d ("e1000e: fix heap overflow in e1000_set_eeprom"), however,
corrections for RCT have been kept.
Emil Tantilov [Tue, 25 Nov 2025 22:36:24 +0000 (14:36 -0800)]
idpf: convert vport state to bitmap
Convert vport state to a bitmap and remove the DOWN state which is
redundant in the existing logic. There are no functional changes aside
from the use of bitwise operations when setting and checking the states.
Removed the double underscore to be consistent with the naming of other
bitmaps in the header and renamed current_state to vport_is_up to match
the meaning of the new variable.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Chittim Madhu <madhu.chittim@intel.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Samuel Salin <Samuel.salin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20251125223632.1857532-6-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Natalia Wochtman [Tue, 25 Nov 2025 22:36:23 +0000 (14:36 -0800)]
ixgbevf: ixgbevf_q_vector clean up
Flex array should be at the end of the structure and use [] syntax
Remove unused fields of ixgbevf_q_vector.
They aren't used since busy poll was moved to core code in commit 508aac6dee02 ("ixgbevf: get rid of custom busy polling code").
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Natalia Wochtman <natalia.wochtman@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20251125223632.1857532-5-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiko Carstens [Wed, 26 Nov 2025 14:22:42 +0000 (15:22 +0100)]
dibs: Remove KMSG_COMPONENT macro
The KMSG_COMPONENT macro is a leftover of the s390 specific "kernel message
catalog" from 2008 [1] which never made it upstream.
The macro was added to s390 code to allow for an out-of-tree patch which
used this to generate unique message ids. Also this out-of-tree doesn't
exist anymore.
The pattern of how the KMSG_COMPONENT is used was partially also used for
non s390 specific code, for whatever reasons.
Remove the macro in order to get rid of a pointless indirection.
Breno Leitao [Wed, 26 Nov 2025 10:54:40 +0000 (02:54 -0800)]
net: thunder: convert to use .get_rx_ring_count
Convert the Cavium Thunder NIC VF driver to use the new .get_rx_ring_count
ethtool operation instead of implementing .get_rxnfc solely for handling
ETHTOOL_GRXRINGS command. This simplifies the code by removing the
switch statement and replacing it with a direct return of the queue
count.
The new callback provides the same functionality in a more direct way,
following the ongoing ethtool API modernization.
Alexey Kodanev [Wed, 26 Nov 2025 10:43:27 +0000 (10:43 +0000)]
net: stmmac: fix rx limit check in stmmac_rx_zc()
The extra "count >= limit" check in stmmac_rx_zc() is redundant and
has no effect because the value of "count" doesn't change after the
while condition at this point.
However, it can change after "read_again:" label:
while (count < limit) {
...
if (count >= limit)
break;
read_again:
...
/* XSK pool expects RX frame 1:1 mapped to XSK buffer */
if (likely(status & rx_not_ls)) {
xsk_buff_free(buf->xdp);
buf->xdp = NULL;
dirty++;
count++;
goto read_again;
}
...
This patch addresses the same issue previously resolved in stmmac_rx()
by commit fa02de9e7588 ("net: stmmac: fix rx budget limit check").
The fix is the same: move the check after the label to ensure that it
bounds the goto loop.
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/20251126104327.175590-1-aleksei.kodanev@bell-sw.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Yang [Wed, 26 Nov 2025 08:40:19 +0000 (16:40 +0800)]
net: dsa: yt921x: Fix parsing MIB attributes
There are hard-to-find unused fields in the MIB table I didn't notice in
the example driver code, causing wrong interpretation of the MIB data.
For some 64-bit attributes, the current (wrong) implementation took the
correct lower 32 bits, but messed up the upper 32 bits, so it would work
accidentally until 32-bit overflows happen. Fix that too.
Javen Xu [Wed, 26 Nov 2025 05:59:50 +0000 (13:59 +0800)]
r8169: add DASH support for RTL8127AP
This adds DASH support for chip RTL8127AP. Its mac version is
RTL_GIGA_MAC_VER_80. DASH is a standard for remote management of network
device, allowing out-of-band control.
Peter Enderborg [Wed, 26 Nov 2025 13:54:06 +0000 (14:54 +0100)]
if_ether.h: Clarify ethertype validity for gsw1xx dsa
This 0x88C3 is registered to Infineon Technologies Corporate Research ST
and are used by MaxLinear.
Infineon made a spin off called Lantiq.
Lantiq was acquired by Intel
MaxLinear acquired Intels Connected Home division.
The product FAQ from MaxLinear describes it's history from the F24S.
The driver for the gsw1xx is based on Lantiq showing it's similarities.
Use DEFINE_RAW_FLEX() to avoid a -Wflex-array-member-not-at-end warning.
Remove fixed-size array struct usb_cdc_ncm_dpe16 dpe16[2]; from struct
mbim_tx_hdr, so that flex-array member struct mbim_tx_hdr::ndp16.dpe16[]
ends last in this structure.
Compensate for this by using the DEFINE_RAW_FLEX() helper to declare the
on-stack struct instance that contains struct usb_cdc_ncm_ndp16 as a
member. Adjust the rest of the code, accordingly.
So, with these changes fix the following warning:
drivers/net/wwan/mhi_wwan_mbim.c:81:34: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Max Yuan [Thu, 27 Nov 2025 00:07:51 +0000 (00:07 +0000)]
gve: Fix race condition on tx->dropped_pkt update
The tx->dropped_pkt counter is a 64-bit integer that is incremented
directly. On 32-bit architectures, this operation is not atomic and
can lead to read/write tearing if a reader accesses the counter during
the update. This can result in incorrect values being reported for
dropped packets.
To prevent this potential data corruption, wrap the increment
operation with u64_stats_update_begin() and u64_stats_update_end().
This ensures that updates to the 64-bit counter are atomic, even on
32-bit systems, by using a sequence lock.
The u64_stats_sync API requires the writer to have exclusive access,
which is already provided in this context by the network stack's
serialization of the transmit path (net_device_ops::ndo_start_xmit
[1]) for a given queue.
Jakub Kicinski [Thu, 27 Nov 2025 01:43:11 +0000 (17:43 -0800)]
net: restore napi_consume_skb()'s NULL-handling
Commit e20dfbad8aab ("net: fix napi_consume_skb() with alien skbs")
added a skb->cpu check to napi_consume_skb(), before the point where
napi_consume_skb() validated skb is not NULL.
Add an explicit check to the early exit condition.
Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 26 Nov 2025 03:48:19 +0000 (19:48 -0800)]
eth: bnxt: make use of napi_consume_skb()
As those following recent changes from Eric know very well
using NAPI skb cache is crucial to achieve good perf, at
least on recent AMD platforms. Make sure bnxt feeds the skb
cache with Tx skbs.
Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In include/uapi/linux/netfilter/nf_tables.h,
correct the kernel-doc comments for mistyped enum names and enum values to
avoid these kernel-doc warnings and improve the documentation:
nf_tables.h:896: warning: Enum value 'NFT_EXTHDR_OP_TCPOPT' not described
in enum 'nft_exthdr_op'
nf_tables.h:896: warning: Excess enum value 'NFT_EXTHDR_OP_TCP' description
in 'nft_exthdr_op'
nf_tables.h:1210: warning: expecting prototype for enum
nft_flow_attributes. Prototype was for enum nft_offload_attributes instead
nf_tables.h:1428: warning: expecting prototype for enum nft_reject_code.
Prototype was for enum nft_reject_inet_code instead
(add beginning '@' to each enum value description:)
nf_tables.h:1493: warning: Enum value 'NFTA_TPROXY_FAMILY' not described
in enum 'nft_tproxy_attributes'
nf_tables.h:1493: warning: Enum value 'NFTA_TPROXY_REG_ADDR' not described
in enum 'nft_tproxy_attributes'
nf_tables.h:1493: warning: Enum value 'NFTA_TPROXY_REG_PORT' not described
in enum 'nft_tproxy_attributes'
nf_tables.h:1796: warning: expecting prototype for enum
nft_device_attributes. Prototype was for enum
nft_devices_attributes instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Randy Dunlap [Sat, 1 Nov 2025 19:20:50 +0000 (12:20 -0700)]
netfilter: ip6t_srh: fix UAPI kernel-doc comments format
Fix the kernel-doc format for struct members to be "@member" instead of
"@ member" to avoid kernel-doc warnings.
Warning: ip6t_srh.h:60 struct member 'next_hdr' not described in 'ip6t_srh'
Warning: ip6t_srh.h:60 struct member 'hdr_len' not described in 'ip6t_srh'
Warning: ip6t_srh.h:60 struct member 'segs_left' not described
in 'ip6t_srh'
Warning: ip6t_srh.h:60 struct member 'last_entry' not described
in 'ip6t_srh'
Warning: ip6t_srh.h:60 struct member 'tag' not described in 'ip6t_srh'
Warning: ip6t_srh.h:60 struct member 'mt_flags' not described in 'ip6t_srh'
Warning: ip6t_srh.h:60 struct member 'mt_invflags' not described
in 'ip6t_srh'
Warning: ip6t_srh.h:93 struct member 'next_hdr' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'hdr_len' not described in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'segs_left' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'last_entry' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'tag' not described in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'psid_addr' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'nsid_addr' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'lsid_addr' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'psid_msk' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'nsid_msk' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'lsid_msk' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'mt_flags' not described
in 'ip6t_srh1'
Warning: ip6t_srh.h:93 struct member 'mt_invflags' not described
in 'ip6t_srh1'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Lorenzo Bianconi [Thu, 27 Nov 2025 22:21:43 +0000 (23:21 +0100)]
selftests: netfilter: nft_flowtable.sh: Add the capability to send IPv6 TCP traffic
Introduce the capability to send TCP traffic over IPv6 to
nft_flowtable netfilter selftest.
Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_connlimit: add support to object update operation
This is useful to update the limit or flags without clearing the
connections tracked. Use READ_ONCE() on packetpath as it can be modified
on controlplane.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_connlimit: update the count if add was skipped
Connlimit expression can be used for all kind of packets and not only
for packets with connection state new. See this ruleset as example:
table ip filter {
chain input {
type filter hook input priority filter; policy accept;
tcp dport 22 ct count over 4 counter
}
}
Currently, if the connection count goes over the limit the counter will
count the packets. When a connection is closed, the connection count
won't decrement as it should because it is only updated for new
connections due to an optimization on __nf_conncount_add() that prevents
updating the list if the connection is duplicated.
To solve this problem, check whether the connection was skipped and if
so, update the list. Adjust count_tree() too so the same fix is applied
for xt_connlimit.
Fixes: 976afca1ceba ("netfilter: nf_conncount: Early exit in nf_conncount_lookup() and cleanup") Closes: https://lore.kernel.org/netfilter/trinity-85c72a88-d762-46c3-be97-36f10e5d9796-1761173693813@3c-app-mailcom-bs12/ Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
projects / thirdparty / kernel / linux.git / log
