Adds the Lenovo T580 to the SMBus intertouch list for Synaptics
touchpads. I've tested with this for a week now, and it seems a great
improvement. It's also nice to have the complaint gone from dmesg.
Signed-off-by: Nick Black <dankamongmen@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a latest Lenovo laptop, the trackpoint and 3 buttons below it
don't work at all, when we move the trackpoint or press those 3
buttons, the kernel will print out:
"Rejected trackstick packet from non DualPoint device"
This device is identified as an alps touchpad but the packet has
trackpoint format, so the alps.c drops the packet and prints out
the message above.
According to XiaoXiao's explanation, this device is named cs19 and
is trackpoint-only device, its firmware is only for trackpoint, it
is independent of touchpad and is a device completely different from
DualPoint ones.
To drive this device with mininal changes to the existing driver, we
just let the alps driver not handle this device, then the trackpoint.c
will be the driver of this device if the trackpoint driver is enabled.
(if not, this device will fallback to a bare PS/2 device)
With the trackpoint.c, this trackpoint and 3 buttons all work well,
they have all features that the trackpoint should have, like
scrolling-screen, drag-and-drop and frame-selection.
The GTCO tablet input driver configures itself from an HID report sent
via USB during the initial enumeration process. Some debugging messages
are generated during the parsing. A debugging message indentation
counter is not bounds checked, leading to the ability for a specially
crafted HID report to cause '-' and null bytes be written past the end
of the indentation array. As long as the kernel has CONFIG_DYNAMIC_DEBUG
enabled, this code will not be optimized out. This was discovered
during code review after a previous syzkaller bug was found in this
driver.
Commit 9baf30972b55 ("bcache: fix for gc and write-back race") added a
new work queue dc->writeback_write_wq, but forgot to destroy it in the
error condition when creating dc->writeback_thread failed.
This patch destroys dc->writeback_write_wq if kthread_create() returns
error pointer to dc->writeback_thread, then a memory leak is avoided.
Fixes: 9baf30972b55 ("bcache: fix for gc and write-back race") Signed-off-by: Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When md raid device (e.g. raid456) is used as backing device, read-ahead
requests on a degrading and recovering md raid device might be failured
immediately by md raid code, but indeed this md raid array can still be
read or write for normal I/O requests. Therefore such failed read-ahead
request are not real hardware failure. Further more, after degrading and
recovering accomplished, read-ahead requests will be handled by md raid
array again.
For such condition, I/O failures of read-ahead requests don't indicate
real health status (because normal I/O still be served), they should not
be counted into I/O error counter dc->io_errors.
Since there is no simple way to detect whether the backing divice is a
md raid device, this patch simply ignores I/O failures for read-ahead
bios on backing device, to avoid bogus backing device failure on a
degrading md raid array.
This patch depends on commit c4dc2497d50d ("bcache: fix high CPU
occupancy during journal") which is reverted in previous patch. So
revert this one too.
Fixes: 6268dc2c4703 ("bcache: free heap cache_set->flush_btree in bch_journal_free") Signed-off-by: Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Cc: Shenghui Wang <shhuiw@foxmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enlarges a race between normal btree flush code path and
flush_btree_write(), which causes deadlock when journal space is
exhausted. Reverts this patch makes the race window from 128 btree
nodes to only 1 btree nodes.
Fixes: c4dc2497d50d ("bcache: fix high CPU occupancy during journal") Signed-off-by: Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Cc: Tang Junhui <tang.junhui.linux@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although this patch helps the failed bcache device to stop faster when
too many I/O errors detected on corresponding cached device, setting
CACHE_SET_IO_DISABLE bit to cache set c->flags was not a good idea. This
operation will disable all I/Os on cache set, which means other attached
bcache devices won't work neither.
Without this patch, the failed bcache device can also be stopped
eventually if internal I/O accomplished (e.g. writeback). Therefore here
I revert it.
Fixes: 6147305c73e4 ("bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()") Reported-by: Yong Li <mr.liyong@qq.com> Signed-off-by: Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent deadlock between open_shroot() and
cifs_mark_open_files_invalid() by releasing the lock before entering
SMB2_open, taking it again after and checking if we still need to use
the result.
Link: https://lore.kernel.org/linux-cifs/684ed01c-cbca-2716-bc28-b0a59a0f8521@prodrive-technologies.com/T/#u Fixes: 3d4ef9a15343 ("smb3: fix redundant opens on root") Signed-off-by: Aurelien Aptel <aaptel@suse.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Servers can defer destaging any data and updating the mtime until close().
This means that if we do a setinfo to modify the mtime while other handles
are open for write the server may overwrite our setinfo timestamps when
if flushes the file on close() of the writeable handle.
To solve this we add an explicit flush when the mtime is about to
be updated.
This fixes "cp -p" to preserve mtime when copying a file onto an SMB2 share.
CC: Stable <stable@vger.kernel.org> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix mount options comparison when serverino option is turned off later
in cifs_autodisable_serverino() and thus avoiding mismatch of new cifs
mounts.
Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <paulo@paulo.ac> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilove@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In low memory situations the various SMB2_*_init() functions can fail
to allocate a request PDU and thus leave the request iovector as NULL.
If we don't check the return code for failure we end up calling
smb2_set_next_command() with a NULL iovector causing a crash when it tries
to dereference it.
CC: Stable <stable@vger.kernel.org> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AES GCM function reuses an 'op' data structure, which members
contain values that must be cleared for each (re)use.
This fix resolves a crypto self-test failure:
alg: aead: gcm-aes-ccp encryption test failed (wrong result) on test vector 2, cfg="two even aligned splits"
Fixes: 36cf515b9bbe ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware automatically zero pads incomplete block ciphers
blocks without raising any errors. This is a screw-up. This
was noticed by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS tests that
sent a incomplete blocks and expect them to fail.
This fixes:
cbc-aes-ppc4xx encryption unexpectedly succeeded on test vector
"random: len=2409 klen=32"; expected_error=-22, cfg="random:
may_sleep use_digest src_divs=[96.90%@+2295, 2.34%@+4066,
0.32%@alignmask+12, 0.34%@+4087, 0.9%@alignmask+1787, 0.1%@+3767]
iv_offset=6"
ecb-aes-ppc4xx encryption unexpectedly succeeded on test vector
"random: len=1011 klen=32"; expected_error=-22, cfg="random:
may_sleep use_digest src_divs=[100.0%@alignmask+20]
dst_divs=[3.12%@+3001, 96.88%@+4070]"
Cc: Eric Biggers <ebiggers@kernel.org> Cc: stable@vger.kernel.org [4.19, 5.0 and 5.1] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the hardware consider them to be blockciphers, the
reference implementation defines them as streamciphers.
Do the right thing and set the blocksize to 1. This
was found by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS.
This fixes the following issues:
skcipher: blocksize for ofb-aes-ppc4xx (16) doesn't match generic impl (1)
skcipher: blocksize for cfb-aes-ppc4xx (16) doesn't match generic impl (1)
Cc: Eric Biggers <ebiggers@kernel.org> Cc: stable@vger.kernel.org Fixes: f2a13e7cba9e ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear the CRYPTO_TFM_REQ_MAY_SLEEP flag when the chacha20poly1305
operation is being continued from an async completion callback, since
sleeping may not be allowed in that context.
This is basically the same bug that was recently fixed in the xts and
lrw templates. But, it's always been broken in chacha20poly1305 too.
This was found using syzkaller in combination with the updated crypto
self-tests which actually test the MAY_SLEEP flag now.
The sha256-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: the actual digest, result: initial
value of SHA internal state. The error is in sha256_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha2_ce_transform to make the final round. However, in
sha256_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 03802f6a80b3a ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by: Elena Petrova <lenaptr@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sha1-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: da39a3ee..., result: 67452301...
(initial value of SHA internal state). The error is in sha1_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha1_ce_transform to make the final round. However, in
sha1_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 07eb54d306f4 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by: Elena Petrova <lenaptr@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error code read from the queue status register is only 6 bits wide,
but we need to verify its value is within range before indexing the error
messages.
Fixes: 81422badb3907 ("crypto: ccp - Make syslog errors human-readable") Cc: <stable@vger.kernel.org> Reported-by: Cfir Cohen <cfir@google.com> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CAAM driver currently violates an undocumented and slightly
controversial requirement imposed by the crypto stack that a buffer
referred to by the request structure via its virtual address may not
be modified while any scatterlists passed via the same request
structure are mapped for inbound DMA.
This may result in errors like
alg: aead: decryption failed on test 1 for gcm_base(ctr-aes-caam,ghash-generic): ret=74
alg: aead: Failed to load transform for gcm(aes): -2
on non-cache coherent systems, due to the fact that the GCM driver
passes an IV buffer by virtual address which shares a cacheline with
the auth_tag buffer passed via a scatterlist, resulting in corruption
of the auth_tag when the IV is updated while the DMA mapping is live.
Since the IV that is returned to the caller is only valid for CBC mode,
and given that the in-kernel users of CBC (such as CTS) don't trigger the
same issue as the GCM driver, let's just disable the output IV generation
for all modes except CBC for the time being.
Fixes: 854b06f76879 ("crypto: caam - properly set IV after {en,de}crypt") Cc: Horia Geanta <horia.geanta@nxp.com> Cc: Iuliana Prodan <iuliana.prodan@nxp.com> Reported-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changing ghash_mod_init() to be subsys_initcall made it start running
before the alignment fault handler has been installed on ARM. In kernel
builds where the keys in the ghash test vectors happened to be
misaligned in the kernel image, this exposed the longstanding bug that
ghash_setkey() is incorrectly casting the key buffer (which can have any
alignment) to be128 for passing to gf128mul_init_4k_lle().
Fix this by memcpy()ing the key to a temporary buffer.
Don't fix it by setting an alignmask on the algorithm instead because
that would unnecessarily force alignment of the data too.
Fixes: 2cdc6899a88e ("crypto: ghash - Add GHASH digest algorithm for GCM") Reported-by: Peter Robinson <pbrobinson@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A system bus error during a PDMA transfer can mess up the calculation of
the transfer residual (the PDMA handshaking hardware lacks a byte
counter). This results in data corruption.
The algorithm in this patch anticipates a bus error by starting each
transfer with a MOVE.B instruction. If a bus error is caught the transfer
will be retried. If a bus error is caught later in the transfer (for a
MOVE.W instruction) the transfer gets failed and subsequent requests for
that target will use PIO instead of PDMA.
This avoids the "!REQ and !ACK" error so the severity level of that message
is reduced to KERN_DEBUG.
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bfa907 ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reported-by: Chris Jones <chris@martin-jones.com> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some targets introduce delays when handshaking the response to certain
commands. For example, a disk may send a 96-byte response to an INQUIRY
command (or a 24-byte response to a MODE SENSE command) too slowly.
Apparently the first 12 or 14 bytes are handshaked okay but then the system
bus error timeout is reached while transferring the next word.
Since the scsi bus phase hasn't changed, the driver then sets the target
borken flag to prevent further PDMA transfers. The driver also logs the
warning, "switching to slow handshake".
Raise the PDMA threshold to 512 bytes so that PIO transfers will be used
for these commands. This default is sufficiently low that PDMA will still
be used for READ and WRITE commands.
The existing threshold (16 bytes) was chosen more or less at random.
However, best performance requires the threshold to be as low as possible.
Those systems that don't need the PIO workaround at all may benefit from
mac_scsi.setup_use_pdma=1
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bfa907 ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In megasas_get_target_prop(), driver is incorrectly calculating the target
ID for devices with channel 1 and 3. Due to this, firmware will either
fail the command (if there is no device with the target id sent from
driver) or could return the properties for a target which was not
intended. Devices could end up with the wrong queue depth due to this.
Fix target id calculation for channel 1 and 3.
Fixes: 96188a89cc6d ("scsi: megaraid_sas: NVME interface target prop added") Cc: stable@vger.kernel.org Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tracing instances where we open and close WKA ports, we also pass the
request-ID of the respective FSF command.
But after successfully sending the FSF command we must not use the
request-object anymore, as this might result in an use-after-free (see
"zfcp: fix request object use-after-free in send path causing seqno
errors" ).
To fix this add a new variable that caches the request-ID before sending
the request. This won't change during the hand-off to the FCP channel,
and so it's safe to trace this cached request-ID later, instead of using
the request object.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com> Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Steffen Maier <maier@linux.ibm.com> Reviewed-by: Jens Remus <jremus@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a recent change to our send path for FSF commands we introduced a
possible use-after-free of request-objects, that might further lead to
zfcp crafting bad requests, which the FCP channel correctly complains
about with an error (FSF_PROT_SEQ_NUMB_ERROR). This error is then handled
by an adapter-wide recovery.
The following sequence illustrates the possible use-after-free:
static int zfcp_fsf_req_send(struct zfcp_fsf_req *req)
{
struct zfcp_adapter *adapter = req->adapter;
struct zfcp_qdio *qdio = adapter->qdio;
...
zfcp_reqlist_add(adapter->req_list, req);
// ^^^^^^^^^^^^^^^^
// add request to our driver-internal hash-table for tracking
// (protected by separate lock req_list->lock)
...
if (zfcp_qdio_send(qdio, &req->qdio_req)) {
// ^^^^^^^^^^^^^^
// hand-off the request to FCP channel;
// the request can complete at any point now
...
}
/* Don't increase for unsolicited status */
if (!zfcp_fsf_req_is_status_read_buffer(req))
// ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
// possible use-after-free
adapter->fsf_req_seq_no++;
// ^^^^^^^^^^^^^^^^
// because of the use-after-free we might
// miss this accounting, and as follow-up
// this results in the FCP channel error
// FSF_PROT_SEQ_NUMB_ERROR
adapter->req_no++;
static void zfcp_fsf_req_complete(struct zfcp_fsf_req *req)
{
...
if (likely(req->status & ZFCP_STATUS_FSFREQ_CLEANUP))
zfcp_fsf_req_free(req);
// ^^^^^^^^^^^^^^^^^
// free memory for request-object
else
complete(&req->completion);
// ^^^^^^^^
// completion notification for code-paths that wait
// synchronous for the completion of the request; in
// those the memory is freed separately
}
The result of the use-after-free only affects the send path, and can not
lead to any data corruption. In case we miss the sequence-number
accounting, because the memory was already re-purposed, the next FSF
command will fail with said FCP channel error, and we will recover the
whole adapter. This causes no additional errors, but it slows down
traffic. There is a slight chance of the same thing happen again
recursively after the adapter recovery, but so far this has not been seen.
This was seen under z/VM, where the send path might run on a virtual CPU
that gets scheduled away by z/VM, while the return path might still run,
and so create the necessary timing. Running with KASAN can also slow down
the kernel sufficiently to run into this user-after-free, and then see the
report by KASAN.
To fix this, simply pull the test for the sequence-number accounting in
front of the hand-off to the FCP channel (this information doesn't change
during hand-off), but leave the sequence-number accounting itself where it
is.
To make future regressions of the same kind less likely, add comments to
all closely related code-paths.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com> Fixes: f9eca0227600 ("scsi: zfcp: drop duplicate fsf_command from zfcp_fsf_req which is also in QTCB header") Cc: <stable@vger.kernel.org> #5.0+ Reviewed-by: Steffen Maier <maier@linux.ibm.com> Reviewed-by: Jens Remus <jremus@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild test robot gets the following compilation warning using gcc 7.4
cross compilation for c6x (GCC_VERSION=7.4.0 make.cross ARCH=c6x).
In file included from include/asm-generic/bug.h:18:0,
from arch/c6x/include/asm/bug.h:12,
from include/linux/bug.h:5,
from include/linux/thread_info.h:12,
from include/asm-generic/current.h:5,
from ./arch/c6x/include/generated/asm/current.h:1,
from include/linux/sched.h:12,
from include/linux/blkdev.h:5,
from drivers//scsi/sd_zbc.c:11:
drivers//scsi/sd_zbc.c: In function 'sd_zbc_read_zones':
>> include/linux/kernel.h:62:48: warning: 'zone_blocks' may be used
uninitialized in this function [-Wmaybe-uninitialized]
#define __round_mask(x, y) ((__typeof__(x))((y)-1))
^
drivers//scsi/sd_zbc.c:464:6: note: 'zone_blocks' was declared here
u32 zone_blocks;
^~~~~~~~~~~
This is a false-positive report. The variable zone_blocks is always
initialized in sd_zbc_check_zones() before use. It is not initialized
only and only if sd_zbc_check_zones() fails.
Avoid this warning by initializing the zone_blocks variable to 0.
Fixes: 5f832a395859 ("scsi: sd_zbc: Fix sd_zbc_check_zones() error checks") Cc: Stable <stable@vger.kernel.org> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When scsi_init_sense_cache(host) is called concurrently from different
hosts, each code path may find that no cache has been created and
allocate a new one. The lack of locking can lead to potentially
overriding a cache allocated by a different host.
Fix the issue by moving 'mutex_lock(&scsi_sense_cache_mutex)' before
scsi_select_sense_cache().
Fixes: 0a6ac4ee7c21 ("scsi: respect unchecked_isa_dma for blk-mq") Cc: Stable <stable@vger.kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of that commit was to suppress a timeout warning message which
appeared to be caused by target latency. But suppressing the warning is
undesirable as the warning may indicate a messed up transfer count.
Another problem with that commit is that 15 ms is too long to keep
interrupts disabled as interrupt latency can cause system clock drift and
other problems.
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org Fixes: 4822827a69d7 ("scsi: ncr5380: Increase register polling limit") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A PDMA error is handled in the core driver by setting the device's 'borken'
flag and aborting the command. Unfortunately, do_abort() is not
dependable. Perform a SCSI bus reset instead, to make sure that the command
fails and gets retried.
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.20+ Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reselection interrupt gets disabled during selection and must be
re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a
disconnected command may time-out or the target may wedge the bus while
trying to reselect the host. This can happen after a command is aborted.
Fix this by enabling the reselection interrupt in NCR5380_main() after
calls to NCR5380_select() and NCR5380_information_transfer() return.
Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.9+ Fixes: 8b00c3d5d40d ("ncr5380: Implement new eh_abort_handler") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Stan Johnson <userm57@yahoo.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of trying to allocate pages with GFP_USER in
add_ballooned_pages() check the available free memory via
si_mem_available(). GFP_USER is far less limiting memory exhaustion
than the test via si_mem_available().
This will avoid dom0 running out of memory due to excessive foreign
page mappings especially on ARM and on x86 in PVH mode, as those don't
have a pre-ballooned area which can be used for foreign mappings.
As the normal ballooning suffers from the same problem don't balloon
down more than si_mem_available() pages in one iteration. At the same
time limit the default maximum number of retries.
This fixes a global out-of-bounds read access in the copy_buffer
function of the floppy driver.
The FDDEFPRM ioctl allows one to set the geometry of a disk. The sect
and head fields (unsigned int) of the floppy_drive structure are used to
compute the max_sector (int) in the make_raw_rw_request function. It is
possible to overflow the max_sector. Next, max_sector is passed to the
copy_buffer function and used in one of the memcpy calls.
An unprivileged user could trigger the bug if the device is accessible,
but requires a floppy disk to be inserted.
The patch adds the check for the .sect * .head multiplication for not
overflowing in the set_geometry function.
This fixes the invalid pointer dereference in the drive_name function of
the floppy driver.
The native_format field of the struct floppy_drive_params is used as
floppy_type array index in the drive_name function. Thus, the field
should be checked the same way as the autodetect field.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. Next, FDGETDRVTYP ioctl should
be used to call the drive_name. A floppy disk is not required to be
inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for a value of the native_format field to be in
the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array
indices.
This fixes a global out-of-bounds read access in the next_valid_format
function of the floppy driver.
The values from autodetect field of the struct floppy_drive_params are
used as indices for the floppy_type array in the next_valid_format
function 'floppy_type[DP->autodetect[probed_format]].sect'.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. A floppy disk is not required to
be inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for values of the autodetect field to be in the
'0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices.
This fixes a divide by zero error in the setup_format_params function of
the floppy driver.
Two consecutive ioctls can trigger the bug: The first one should set the
drive geometry with such .sect and .rate values for the F_SECT_PER_TRACK
to become zero. Next, the floppy format operation should be called.
A floppy disk is not required to be inserted. An unprivileged user
could trigger the bug if the device is accessible.
The patch checks F_SECT_PER_TRACK for a non-zero value in the
set_geometry function. The proper check should involve a reasonable
upper limit for the .sect and .rate fields, but it could change the
UAPI.
The patch also checks F_SECT_PER_TRACK in the setup_format_params, and
cancels the formatting operation in case of zero.
The iolatency controller is based on rq_qos. It increments on
rq_qos_throttle() and decrements on either rq_qos_cleanup() or
rq_qos_done_bio(). a3fb01ba5af0 fixes the double accounting issue where
blk_mq_make_request() may call both rq_qos_cleanup() and
rq_qos_done_bio() on REQ_NO_WAIT. So checking STS_AGAIN prevents the
double decrement.
The above works upstream as the only way we can get STS_AGAIN is from
blk_mq_get_request() failing. The STS_AGAIN handling isn't a real
problem as bio_endio() skipping only happens on reserved tag allocation
failures which can only be caused by driver bugs and already triggers
WARN.
However, the fix creates a not so great dependency on how STS_AGAIN can
be propagated. Internally, we (Facebook) carry a patch that kills read
ahead if a cgroup is io congested or a fatal signal is pending. This
combined with chained bios progagate their bi_status to the parent is
not already set can can cause the parent bio to not clean up properly
even though it was successful. This consequently leaks the inflight
counter and can hang all IOs under that blkg.
To nip the adverse interaction early, this removes the rq_qos_cleanup()
callback in iolatency in favor of cleaning up always on the
rq_qos_done_bio() path.
Fixes: a3fb01ba5af0 ("blk-iolatency: only account submitted bios") Debugged-by: Tejun Heo <tj@kernel.org> Debugged-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Dennis Zhou <dennis@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
A recent commit efa14c3985828d ("iavf: allow null RX descriptors") added
a null pointer sanity check on rx_buffer, however, rx_buffer is being
dereferenced before that check, which implies a null pointer dereference
bug can potentially occur. Fix this by only dereferencing rx_buffer
until after the null pointer check.
Addresses-Coverity: ("Dereference before null check") Signed-off-by: Colin Ian King <colin.king@canonical.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When change MTU or other operations, which just calling .reset_notify
to do HNAE3_DOWN_CLIENT and HNAE3_UP_CLIENT, then
the netdev_tx_reset_queue() in the hns3_clear_all_ring() will be
ignored. So the dev_watchdog() may misdiagnose a TX timeout.
This patch separates netdev_tx_reset_queue() from
hns3_clear_all_ring(), and unifies hns3_clear_all_ring() and
hns3_force_clear_all_ring into one, since they are doing
similar things.
Fixes: 3a30964a2eef ("net: hns3: delay ring buffer clearing during reset") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.
Signed-off-by: Josua Mayer <josua@solid-run.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike driver mode, generic xdp receive could be triggered
by different threads on different CPU cores at the same time
leading to the fill and rx queue breakage. For example, this
could happen while sending packets from two processes to the
first interface of veth pair while the second part of it is
open with AF_XDP socket.
Need to take a lock for each generic receive to avoid race.
Fixes: c497176cb2e4 ("xsk: add Rx receive functions and poll support") Signed-off-by: Ilya Maximets <i.maximets@samsung.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: William Tu <u9012063@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current gtp_newlink() could be called after unregister_pernet_subsys().
gtp_newlink() uses gtp_net but it can be destroyed by
unregister_pernet_subsys().
So unregister_pernet_subsys() should be called after
rtnl_link_unregister().
Test commands:
#SHELL 1
while :
do
for i in {1..5}
do
./gtp-link add gtp$i &
done
killall gtp-link
done
gtp_encap_destroy() is called twice.
1. When interface is deleted.
2. When udp socket is destroyed.
either gtp->sk0 or gtp->sk1u could be freed by sock_put() in
gtp_encap_destroy(). so, when gtp_encap_destroy() is called again,
it would uses freed sk pointer.
patch makes gtp_encap_destroy() to set either gtp->sk0 or gtp->sk1u to
null. in addition, both gtp->sk0 and gtp->sk1u pointer are protected
by rtnl_lock. so, rtnl_lock() is added.
Test command:
gtp-link add gtp1 &
killall gtp-link
ip link del gtp1
Fixes: 1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ipv4_pdp_add() is called in RCU read-side critical section.
So GFP_KERNEL should not be used in the function.
This patch make ipv4_pdp_add() to use GFP_ATOMIC instead of GFP_KERNEL.
gtp_encap_enable_socket() and gtp_encap_destroy() are not protected
by rcu_read_lock(). and it's not safe to write sk->sk_user_data.
This patch make these functions to use lock_sock() instead of
rcu_dereference_sk_user_data().
Fixes: 1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.
The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.
The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.
The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
If an invalid role is sent from user space, gtp_encap_enable() will fail.
Then, it should call gtp_encap_disable_sock() but current code doesn't.
It makes memory leak.
Fixes: 91ed81f9abc7 ("gtp: support SGSN-side tunnels") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This change is similar to commit a1616a5ac99e ("Bluetooth: hidp: fix
buffer overflow") but for the compat ioctl. We take a string from the
user and forgot to ensure that it's NUL terminated.
I have also changed the strncpy() in to strscpy() in hidp_setup_hid().
The difference is the strncpy() doesn't necessarily NUL terminate the
destination string. Either change would fix the problem but it's nice
to take a belt and suspenders approach and do both.
Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.
Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.
Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499
L2CAP: Disconnection Request (0x06) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548
L2CAP: Disconnection Response (0x07) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397
L2CAP: Connection Request (0x02) ident 27 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441
L2CAP: Connection Response (0x03) ident 27 len 8
Destination CID: 65
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449
L2CAP: Configure Request (0x04) ident 19 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143
L2CAP: Disconnection Request (0x06) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073
L2CAP: Connection Request (0x02) ident 12 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371
L2CAP: Disconnection Response (0x07) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196
L2CAP: Configure Request (0x04) ident 13 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804
L2CAP: Connection Response (0x03) ident 12 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Fix is to check that channel is in state BT_DISCONN before deleting the
channel.
This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: Matti Kamunen <matti.kamunen@synopsys.com> Reported-by: Ari Timonen <ari.timonen@synopsys.com> Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
'probe libc's inet_pton & backtrace it with ping' testcase sometimes
fails on powerpc because distro ping binary does not have symbol
information and thus it prints "[unknown]" function name in the
backtrace.
Accept "[unknown]" as valid function name for powerpc as well.
# perf test -v "probe libc's inet_pton & backtrace it with ping"
Before:
59: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 79695
ping 79718 [077] 96483.787025: probe_libc:inet_pton: (7fff83a754c8) 7fff83a754c8 __GI___inet_pton+0x8 (/usr/lib64/power9/libc-2.28.so) 7fff83a2b7a0 gaih_inet.constprop.7+0x1020
(/usr/lib64/power9/libc-2.28.so) 7fff83a2c170 getaddrinfo+0x160 (/usr/lib64/power9/libc-2.28.so) 1171830f4 [unknown] (/usr/bin/ping)
FAIL: expected backtrace entry
".*\+0x[[:xdigit:]]+[[:space:]]\(.*/bin/ping.*\)$"
got "1171830f4 [unknown] (/usr/bin/ping)"
test child finished with -1
---- end ----
probe libc's inet_pton & backtrace it with ping: FAILED!
After:
59: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 79085
ping 79108 [045] 96400.214177: probe_libc:inet_pton: (7fffbb9654c8) 7fffbb9654c8 __GI___inet_pton+0x8 (/usr/lib64/power9/libc-2.28.so) 7fffbb91b7a0 gaih_inet.constprop.7+0x1020
(/usr/lib64/power9/libc-2.28.so) 7fffbb91c170 getaddrinfo+0x160 (/usr/lib64/power9/libc-2.28.so) 132e830f4 [unknown] (/usr/bin/ping)
test child finished with 0
---- end ----
probe libc's inet_pton & backtrace it with ping: Ok
Signed-off-by: Seeteena Thoufeek <s1seetee@linux.vnet.ibm.com> Reviewed-by: Kim Phillips <kim.phillips@amd.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hendrik Brueckner <brueckner@linux.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sandipan Das <sandipan@linux.ibm.com> Fixes: 1632936480a5 ("perf tests: Fix record+probe_libc_inet_pton.sh without ping's debuginfo") Link: http://lkml.kernel.org/r/1561630614-3216-1-git-send-email-s1seetee@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The NMI handlers handle_percpu_devid_fasteoi_nmi() and handle_fasteoi_nmi()
do not update the interrupt counts. Due to that the NMI interrupt count
does not show up correctly in /proc/interrupts.
Add the statistics and treat the NMI handlers in the same way as per cpu
interrupts and prevent them from updating irq_desc::tot_count as this might
be corrupted due to concurrency.
Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.
For one peer, no checks are performed to see if it is meant to receive
packets for a given address.
As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Tested-by: Michael Scott <mike@foundries.io> Signed-off-by: Josua Mayer <josua.mayer@jm0.eu> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For revision 0x20, the broadcast promisc is enabled by firmware,
it's unnecessary to enable it when initializing VF.
For revision 0x21, it's necessary to enable broadcast promisc mode
when initializing or re-initializing VF, otherwise, it will be
unable to send and receive promisc packets.
Fixes: f01f5559cac8 ("net: hns3: don't allow vf to enable promisc mode") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code is assuming char pointers in format, which is not always
true at least for powerpc. Fixing this by dumping the whole string
into buffer based on its format.
Please note that libopcodes code does not check return values from
fprintf callback, but as per Jakub suggestion returning -1 on allocation
failure so we do the best effort to propagate the error.
Fixes: 107f041212c1 ("tools: bpftool: add JSON output for `bpftool prog dump jited *` command") Reported-by: Michael Petlan <mpetlan@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling of_node_put() on the codec_ep and codec_port variables,
they are still being used, which may result in use-after-free.
We fix this issue by calling of_node_put() after the last usage.
Fixes: fce9b90c1ab7 ("ASoC: audio-graph-card: cleanup DAI link loop method - step2") Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/1562229530-8121-1-git-send-email-wen.yang99@zte.com.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 372e722ea4dd4ca1 ("gpiolib: use descriptors internally") renamed
the functions to use a "gpiod" prefix, and commit 79a9becda8940deb
("gpiolib: export descriptor-based GPIO interface") introduced the "raw"
variants, but both changes forgot to update the comments.
Readd a similar reference to gpiod_set_value(), which was accidentally
removed by commit 1e77fc82110ac36f ("gpio: Add missing open drain/source
handling to gpiod_set_value_cansleep()").
Selftests are reporting this failure in test_lwt_seg6local.sh:
+ ip netns exec ns2 ip -6 route add fb00::6 encap bpf in obj test_lwt_seg6local.o sec encap_srh dev veth2
Error fetching program/map!
Failed to parse eBPF program: Operation not permitted
The problem is __attribute__((always_inline)) alone is not enough to prevent
clang from inserting those functions in .text. In that case, .text is not
marked as relocateable.
See the output of objdump -h test_lwt_seg6local.o:
This causes the iproute bpf loader to fail in bpf_fetch_prog_sec:
bpf_has_call_data returns true but bpf_fetch_prog_relo fails as there's no
relocateable .text section in the file.
To fix this, convert to 'static __always_inline'.
v2: Use 'static __always_inline' instead of 'static inline
__attribute__((always_inline))'
Fixes: c99a84eac026 ("selftests/bpf: test for seg6local End.BPF action") Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
At the head of function, it directly access 'attr' without checking
if it's NULL pointer. This patch moves the values assignment after
validating 'attr' and 'attr->file'.
Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC8 started emitting warning about using strncpy with number of bytes
exactly equal destination size, which is generally unsafe, as can lead
to non-zero terminated string being copied. Use IFNAMSIZ - 1 as number
of bytes to ensure name is always zero-terminated.
Signed-off-by: Andrii Nakryiko <andriin@fb.com> Cc: Magnus Karlsson <magnus.karlsson@intel.com> Acked-by: Yonghong Song <yhs@fb.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the rxrpc_eproto tracepoint is enabled, an oops will be cause by the
trace line that rxrpc_extract_header() tries to emit when a protocol error
occurs (typically because the packet is short) because the call argument is
NULL.
Fix this by using ?: to assume 0 as the debug_id if call is NULL.
Fixes: a25e21f0bcd2 ("rxrpc, afs: Use debug_ids rather than pointers in traces") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently bnx2x ptp worker tries to read a register with timestamp
information in case of TX packet timestamping and in case it fails,
the routine reschedules itself indefinitely. This was reported as a
kworker always at 100% of CPU usage, which was narrowed down to be
bnx2x ptp_task.
By following the ioctl handler, we could narrow down the problem to
an NTP tool (chrony) requesting HW timestamping from bnx2x NIC with
RX filter zeroed; this isn't reproducible for example with ptp4l
(from linuxptp) since this tool requests a supported RX filter.
It seems NIC FW timestamp mechanism cannot work well with
RX_FILTER_NONE - driver's PTP filter init routine skips a register
write to the adapter if there's not a supported filter request.
This patch addresses the problem of bnx2x ptp thread's everlasting
reschedule by retrying the register read 10 times; between the read
attempts the thread sleeps for an increasing amount of time starting
in 1ms to give FW some time to perform the timestamping. If it still
fails after all retries, we bail out in order to prevent an unbound
resource consumption from bnx2x.
The patch also adds an ethtool statistic for accounting the skipped
TX timestamp packets and it reduces the priority of timestamping
error messages to prevent log flooding. The code was tested using
both linuxptp and chrony.
Reported-and-tested-by: Przemyslaw Hausman <przemyslaw.hausman@canonical.com> Suggested-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
__vxlan_dev_create() destroys FDB using specific pointer which indicates
a fdb when error occurs.
But that pointer should not be used when register_netdevice() fails because
register_netdevice() internally destroys fdb when error occurs.
This patch makes vxlan_fdb_create() to do not link fdb entry to vxlan dev
internally.
Instead, a new function vxlan_fdb_insert() is added to link fdb to vxlan
dev.
vxlan_fdb_insert() is called after calling register_netdevice().
This routine can avoid situation that ->ndo_uninit() destroys fdb entry
in error path of register_netdevice().
Hence, error path of __vxlan_dev_create() routine can have an opportunity
to destroy default fdb entry by hand.
Test command
ip link add bonding_masters type vxlan id 0 group 239.1.1.1 \
dev enp0s9 dstport 4789
The metric group code tries to find a group it added earlier in the
evlist. Fix the lookup to handle groups with partially overlaps
correctly. When a sub string match fails and we reset the match, we have
to compare the first element again.
I also renamed the find_evsel function to find_evsel_group to make its
purpose clearer.
Event merging is mainly to collapse similar events in lots of different
duplicated PMUs.
It can break metric displaying. It's possible for two metrics to have
the same event, and when the two events happen in a row the second
wouldn't be displayed. This would also not show the second metric.
To avoid this don't merge events in the same PMU. This makes sense, if
we have multiple events in the same PMU there is likely some reason for
it (e.g. using multiple groups) and we better not merge them.
While in theory it would be possible to construct metrics that have
events with the same name in different PMU no current metrics have this
problem.
This is the fix for perf stat -M UPI,IPC (needs also another bug fix to
completely work)
Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Fixes: 430daf2dc7af ("perf stat: Collapse identically named events") Link: http://lkml.kernel.org/r/20190624193711.35241-3-andi@firstfloor.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After setting up metric groups through the event parser, the metricgroup
code looks them up again in the event list.
Make sure we only look up events that haven't been used by some other
metric. The data structures currently cannot handle more than one metric
per event. This avoids problems with multiple events partially
overlapping.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Link: http://lkml.kernel.org/r/20190624193711.35241-2-andi@firstfloor.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To save power, the hda hdmi driver in ASoC invokes snd_hdac_ext_bus_link_put
to disable CORB/RIRB buffers DMA if there is no user of bus and invokes
snd_hdac_ext_bus_link_get to set up CORB/RIRB buffers when it is used.
Unsolicited responses is disabled in snd_hdac_bus_stop_cmd_io called by
snd_hdac_ext_bus_link_put , but it is not enabled in snd_hdac_bus_init_cmd_io
called by snd_hdac_ext_bus_link_get. So for put-get sequence, Unsolicited
responses is disabled and headphone can't be detected by hda codecs.
Now unsolicited responses is only enabled in snd_hdac_bus_reset_link
which resets controller. The function is only called for setup of
controller. This patch enables Unsolicited responses after RIRB is
initialized in snd_hdac_bus_init_cmd_io which works together with
snd_hdac_bus_reset_link to set up controller.
Tested legacy hda driver and SOF driver on intel whiskeylake.
The current logic assumes that the RDMA driver uses one statistics
context adjacent to the ones used by the network driver. This
assumption is not true and the statistics context used by the
RDMA driver is tied to its MSIX base vector. This wrong assumption
can cause RDMA driver failure after changing ethtool rings on the
network side. Fix the statistics reservation logic accordingly.
Fixes: 780baad44f0f ("bnxt_en: Reserve 1 stat_ctx for RDMA driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some chips with older firmware can continue to perform DMA read from
context memory even after the memory has been freed. In the PCI shutdown
method, we need to call pci_disable_device() to shutdown DMA to prevent
this DMA before we put the device into D3hot. DMA memory request in
D3hot state will generate PCI fatal error. Similarly, in the driver
remove method, the context memory should only be freed after DMA has
been shutdown for correctness.
Fixes: 98f04cf0f1fc ("bnxt_en: Check context memory requirements from firmware.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver should delay only in recording stop flow between writing to
DBGC_IN_SAMPLE register and DBGC_OUT_CTRL register. Any other delay is
not needed.
Change the following:
1. Remove any unnecessary delays in the flow
2. Increase the delay in the stop recording flow since 100 micro is
not enough
3. Use usleep_range instead of delay since the driver is allowed to
sleep in this flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Fixes: 5cfe79c8d92a ("iwlwifi: fw: stop and start debugging using host command") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should have got the following reply from command line, but we did not.
From 127.0.0.1 icmp_seq=1 Destination Port Unreachable
Yi Zhao reported it and narrowed it down to: 7fc38225363d ("netfilter: reject: skip csum verification for protocols that don't support it"),
This is because nf_ip_checksum still expects pseudo-header protocol type 0 for
packets that are of neither TCP or UDP, and thus ICMP packets are mistakenly
treated as TCP/UDP.
This patch corrects the conditions in nf_ip_checksum and all other places that
still call it with protocol 0.
Fixes: 7fc38225363d ("netfilter: reject: skip csum verification for protocols that don't support it") Reported-by: Yi Zhao <yi.zhao@windriver.com> Signed-off-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Merge commit 1c8c5a9d38f60 ("Merge
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next") undid the
fix from commit 36f9814a494 ("bpf: fix uapi hole for 32 bit compat
applications") by taking the gpl_compatible 1-bit field definition from
commit b85fab0e67b162 ("bpf: Add gpl_compatible flag to struct
bpf_prog_info") as is. That breaks architectures with 16-bit alignment
like m68k. Add 31-bit pad after gpl_compatible to restore alignment of
following fields.
Thanks to Dmitry V. Levin his analysis of this bug history.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Song Liu <songliubraving@fb.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some buggy scenarios we could possible attempt to transmit frames larger
than maximum MSDU size. Since our devices don't know how to handle this,
it may result in asserts, hangs etc.
This can happen, for example, when we receive a large multicast frame
and try to transmit it back to the air in AP mode.
Since in a legal scenario this should never happen, drop such frames and
warn about it.
Local device and link partner config auto-negotiation on both,
local device config pause frame use as: rx on/tx off,
link partner config pause frame use as: rx off/tx on.
We except the result is:
Local device:
Autonegotiate: on
RX: on
TX: off
RX negotiated: on
TX negotiated: off
Link partner:
Autonegotiate: on
RX: off
TX: on
RX negotiated: off
TX negotiated: on
But actually, the result of Local device and link partner is both:
Autonegotiate: on
RX: off
TX: off
RX negotiated: off
TX negotiated: off
The root cause is that the supported flag is has only Pause,
reference to the function genphy_config_advert():
static int genphy_config_advert(struct phy_device *phydev)
{
...
linkmode_and(phydev->advertising, phydev->advertising,
phydev->supported);
...
}
The pause frame use of link partner is rx off/tx on, so its
advertising only set the bit Asym_Pause, and the supported is
only set the bit Pause, so the result of linkmode_and(), is
rx off/tx off.
This patch adds Asym_Pause to the supported flag to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a packet which is utilizing the launchtime feature (via SO_TXTIME socket
option) also requests the hardware transmit timestamp, the hardware
timestamp is not delivered to the userspace. This is because the value in
skb->tstamp is mistaken as the software timestamp.
Applications, like ptp4l, request a hardware timestamp by setting the
SOF_TIMESTAMPING_TX_HARDWARE socket option. Whenever a new timestamp is
detected by the driver (this work is done in igb_ptp_tx_work() which calls
igb_ptp_tx_hwtstamps() in igb_ptp.c[1]), it will queue the timestamp in the
ERR_QUEUE for the userspace to read. When the userspace is ready, it will
issue a recvmsg() call to collect this timestamp. The problem is in this
recvmsg() call. If the skb->tstamp is not cleared out, it will be
interpreted as a software timestamp and the hardware tx timestamp will not
be successfully sent to the userspace. Look at skb_is_swtx_tstamp() and the
callee function __sock_recv_timestamp() in net/socket.c for more details.
Signed-off-by: Vedang Patel <vedang.patel@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Header Parser allows identifying various fields in the packet
headers, used for various kind of filtering and classification
steps.
This is a re-entrant process, where the offset in the packet header
depends on the previous lookup results. This offset is represented in
the SRAM results of the TCAM, as a shift to be operated.
This shift can be negative in some cases, such as in IPv6 parsing.
This commit prevents overriding the sign bit when setting the shift
value, which could cause instabilities when parsing IPv6 flows.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Suggested-by: Alan Winkowski <walan@marvell.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When hdev->tx_sch_mode is HCLGE_FLAG_VNET_BASE_SCH_MODE, the
hclge_tm_schd_mode_vnet_base_cfg calls hclge_tm_pri_schd_mode_cfg
with vport->vport_id as pri_id, which is used as index for
hdev->tm_info.tc_info, it will cause out of bound access issue
if vport_id is equal to or larger than HNAE3_MAX_TC.
Also hardware only support maximum speed of HCLGE_ETHER_MAX_RATE.
So this patch adds two checks for above cases.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Here is how the above potential deadlock may happen in reboot/shutdown
code path,
1) bcache_reboot() is called firstly in the reboot/shutdown code path,
then in bcache_reboot(), bcache_device_stop() is called.
2) bcache_device_stop() sets BCACHE_DEV_CLOSING on d->falgs, then call
closure_queue(&d->cl) to invoke cached_dev_flush(). And in turn
cached_dev_flush() calls cached_dev_free() via closure_at()
3) In cached_dev_free(), after stopped writebach kthread
dc->writeback_thread, the kwork dc->writeback_write_wq is stopping by
destroy_workqueue().
4) Inside destroy_workqueue(), drain_workqueue() is called. Inside
drain_workqueue(), flush_workqueue() is called. Then wq->lockdep_map
is acquired by lock_map_acquire() in flush_workqueue(). After the
lock acquired the rest part of flush_workqueue() just wait for the
workqueue to complete.
5) Now we look back at writeback thread routine bch_writeback_thread(),
in the main while-loop, write_dirty() is called via continue_at() in
read_dirty_submit(), which is called via continue_at() in while-loop
level called function read_dirty(). Inside write_dirty() it may be
re-called on workqueeu dc->writeback_write_wq via continue_at().
It means when the writeback kthread is stopped in cached_dev_free()
there might be still one kworker queued on dc->writeback_write_wq
to execute write_dirty() again.
6) Now this kworker is scheduled on dc->writeback_write_wq to run by
process_one_work() (which is called by worker_thread()). Before
calling the kwork routine, wq->lockdep_map is acquired.
7) But wq->lockdep_map is acquired already in step 4), so a A-A lock
(lockdep terminology) scenario happens.
Indeed on multiple cores syatem, the above deadlock is very rare to
happen, just as the code comments in process_one_work() says,
2263 * AFAICT there is no possible deadlock scenario between the
2264 * flush_work() and complete() primitives (except for
single-threaded
2265 * workqueues), so hiding them isn't a problem.
But it is still good to fix such lockdep warning, even no one running
bcache on single core system.
The fix is simple. This patch solves the above potential deadlock by,
- Do not destroy workqueue dc->writeback_write_wq in cached_dev_free().
- Flush and destroy dc->writeback_write_wq in writebach kthread routine
bch_writeback_thread(), where after quit the thread main while-loop
and before cached_dev_put() is called.
By this fix, dc->writeback_write_wq will be stopped and destroy before
the writeback kthread stopped, so the chance for a A-A locking on
wq->lockdep_map is disappeared, such A-A deadlock won't happen
any more.
When system memory is in heavy pressure, bch_gc_thread_start() from
run_cache_set() may fail due to out of memory. In such condition,
c->gc_thread is assigned to -ENOMEM, not NULL pointer. Then in following
failure code path bch_cache_set_error(), when cache_set_flush() gets
called, the code piece to stop c->gc_thread is broken,
if (!IS_ERR_OR_NULL(c->gc_thread))
kthread_stop(c->gc_thread);
And KASAN catches such NULL pointer deference problem, with the warning
information:
[ 561.207881] ==================================================================
[ 561.207900] BUG: KASAN: null-ptr-deref in kthread_stop+0x3b/0x440
[ 561.207904] Write of size 4 at addr 000000000000001c by task kworker/15:1/313
Here is how the deadlock happens.
1) bcache_reboot() calls bcache_device_stop(), then inside
bcache_device_stop() BCACHE_DEV_CLOSING bit is set on d->flags.
Then closure_queue(&d->cl) is called to invoke cached_dev_flush().
2) In cached_dev_flush(), cached_dev_free() is called by continu_at().
3) In cached_dev_free(), when stopping the writeback kthread of the
cached device by kthread_stop(), dc->writeback_thread will be waken
up to quite the kthread while-loop, then cached_dev_put() is called
in bch_writeback_thread().
4) Calling cached_dev_put() in writeback kthread may drop dc->count to
0, then dc->detach kworker is scheduled, which is initialized as
cached_dev_detach_finish().
5) Inside cached_dev_detach_finish(), the last line of code is to call
closure_put(&dc->disk.cl), which drops the last reference counter of
closrure dc->disk.cl, then the callback cached_dev_flush() gets
called.
Now cached_dev_flush() is called for second time in the code path, the
first time is in step 2). And again bch_register_lock will be acquired
again, and a A-A lock (lockdep terminology) is happening.
The root cause of the above A-A lock is in cached_dev_free(), mutex
bch_register_lock is held before stopping writeback kthread and other
kworkers. Fortunately now we have variable 'bcache_is_reboot', which may
prevent device registration or unregistration during reboot/shutdown
time, so it is unncessary to hold bch_register_lock such early now.
This is how this patch fixes the reboot/shutdown time A-A lock issue:
After moving mutex_lock(&bch_register_lock) to a later location where
before atomic_read(&dc->running) in cached_dev_free(), such A-A lock
problem can be solved without any reboot time registration race.
When too many I/O errors happen on cache set and CACHE_SET_IO_DISABLE
bit is set, bch_journal() may continue to work because the journaling
bkey might be still in write set yet. The caller of bch_journal() may
believe the journal still work but the truth is in-memory journal write
set won't be written into cache device any more. This behavior may
introduce potential inconsistent metadata status.
This patch checks CACHE_SET_IO_DISABLE bit at the head of bch_journal(),
if the bit is set, bch_journal() returns NULL immediately to notice
caller to know journal does not work.
If CACHE_SET_IO_DISABLE of a cache set flag is set by too many I/O
errors, currently allocator routines can still continue allocate
space which may introduce inconsistent metadata state.
This patch checkes CACHE_SET_IO_DISABLE bit in following allocator
routines,
- bch_bucket_alloc()
- __bch_bucket_alloc_set()
Once CACHE_SET_IO_DISABLE is set on cache set, the allocator routines
may reject allocation request earlier to avoid potential inconsistent
metadata.
Commit 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2") assumes
edac_mc_poll_msec to be unsigned long, but the type of the variable still
remained as int. Setting edac_mc_poll_msec can trigger out-of-bounds
write.
The buggy address belongs to the variable:
edac_mc_poll_msec+0x0/0x40
Memory state around the buggy address: ffffffffb91b2c00: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa ffffffffb91b2c80: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
>ffffffffb91b2d00: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
^ ffffffffb91b2d80: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00 ffffffffb91b2e00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fix it by changing the type of edac_mc_poll_msec to unsigned int.
The reason why this patch adopts unsigned int rather than unsigned long
is msecs_to_jiffies() assumes arg to be unsigned int. We can avoid
integer conversion bugs and unsigned int will be large enough for
edac_mc_poll_msec.
Reviewed-by: James Morse <james.morse@arm.com> Fixes: 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2") Signed-off-by: Eiichi Tsukata <devel@etsukata.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This change fixes a rare race condition of handling WMI events after
wmi_call expires.
wmi_recv_cmd immediately handles an event when reply_buf is defined and
a wmi_call is waiting for the event.
However, in case the wmi_call has already timed-out, there will be no
waiting/running wmi_call and the event will be queued in WMI queue and
will be handled later in wmi_event_handle.
Meanwhile, a new similar wmi_call for the same command and event may
be issued. In this case, when handling the queued event we got WARN_ON
printed.
Fixing this case as a valid timeout and drop the unexpected event.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 3c0efb745a17 ("ath9k: discard undersized packets")
the lower bound of RX packets was set to 10 (min ACK size) to
filter those that would otherwise be treated as invalid at
mac80211.
Alas, short radar pulses are reported as PHY_ERROR frames
with length set to 3. Therefore their detection stopped
working after that commit.
NOTE: ath9k drivers built thereafter will not pass DFS
certification.
This extends the criteria for short packets to explicitly
handle PHY_ERROR frames.
Fixes: 3c0efb745a17 ("ath9k: discard undersized packets") Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
