Commit 408fb0e5aa7fda0059db282ff58c3b2a4278baa0 (xen/pciback: Don't
allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling
MSI-X on passed-through virtual functions, because it checked the VF
for PCI_COMMAND_MEMORY but this is not a valid bit for VFs.
Instead, check the physical function for PCI_COMMAND_MEMORY.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
commit f598282f51 ("PCI: Fix the NIU MSI-X problem in a better way")
teaches us that dealing with MSI-X can be troublesome.
Further checks in the MSI-X architecture shows that if the
PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we
may not be able to access the BAR (since they are memory regions).
Since the MSI-X tables are located in there.. that can lead
to us causing PCIe errors. Inhibit us performing any
operation on the MSI-X unless the MEMORY bit is set.
Note that Xen hypervisor with:
"x86/MSI-X: access MSI-X table only after having enabled MSI-X"
will return:
xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3!
When the generic MSI code tries to setup the PIRQ without
MEMORY bit set. Which means with later versions of Xen
(4.6) this patch is not neccessary.
This is part of XSA-157
Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Otherwise just continue on, returning the same values as
previously (return of 0, and op->result has the PIRQ value).
This does not change the behavior of XEN_PCI_OP_disable_msi[|x].
The pci_disable_msi or pci_disable_msix have the checks for
msi_enabled or msix_enabled so they will error out immediately.
However the guest can still call these operations and cause
us to disable the 'ack_intr'. That means the backend IRQ handler
for the legacy interrupt will not respond to interrupts anymore.
This will lead to (if the device is causing an interrupt storm)
for the Linux generic code to disable the interrupt line.
Naturally this will only happen if the device in question
is plugged in on the motherboard on shared level interrupt GSI.
This is part of XSA-157
Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Otherwise an guest can subvert the generic MSI code to trigger
an BUG_ON condition during MSI interrupt freeing:
for (i = 0; i < entry->nvec_used; i++)
BUG_ON(irq_has_action(entry->irq + i));
Xen PCI backed installs an IRQ handler (request_irq) for
the dev->irq whenever the guest writes PCI_COMMAND_MEMORY
(or PCI_COMMAND_IO) to the PCI_COMMAND register. This is
done in case the device has legacy interrupts the GSI line
is shared by the backend devices.
To subvert the backend the guest needs to make the backend
to change the dev->irq from the GSI to the MSI interrupt line,
make the backend allocate an interrupt handler, and then command
the backend to free the MSI interrupt and hit the BUG_ON.
Since the backend only calls 'request_irq' when the guest
writes to the PCI_COMMAND register the guest needs to call
XEN_PCI_OP_enable_msi before any other operation. This will
cause the generic MSI code to setup an MSI entry and
populate dev->irq with the new PIRQ value.
Then the guest can write to PCI_COMMAND PCI_COMMAND_MEMORY
and cause the backend to setup an IRQ handler for dev->irq
(which instead of the GSI value has the MSI pirq). See
'xen_pcibk_control_isr'.
Then the guest disables the MSI: XEN_PCI_OP_disable_msi
which ends up triggering the BUG_ON condition in 'free_msi_irqs'
as there is an IRQ handler for the entry->irq (dev->irq).
Note that this cannot be done using MSI-X as the generic
code does not over-write dev->irq with the MSI-X PIRQ values.
The patch inhibits setting up the IRQ handler if MSI or
MSI-X (for symmetry reasons) code had been called successfully.
P.S.
Xen PCIBack when it sets up the device for the guest consumption
ends up writting 0 to the PCI_COMMAND (see xen_pcibk_reset_device).
XSA-120 addendum patch removed that - however when upstreaming said
addendum we found that it caused issues with qemu upstream. That
has now been fixed in qemu upstream.
This is part of XSA-157
Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
a) XEN_PCI_OP_enable_msix
b) XEN_PCI_OP_enable_msix
results in hitting an NULL pointer due to using freed pointers.
The device passed in the guest MUST have MSI-X capability.
The a) constructs and SysFS representation of MSI and MSI groups.
The b) adds a second set of them but adding in to SysFS fails (duplicate entry).
'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that
in a) pdev->msi_irq_groups is still set) and also free's ALL of the
MSI-X entries of the device (the ones allocated in step a) and b)).
The unwind code: 'free_msi_irqs' deletes all the entries and tries to
delete the pdev->msi_irq_groups (which hasn't been set to NULL).
However the pointers in the SysFS are already freed and we hit an
NULL pointer further on when 'strlen' is attempted on a freed pointer.
The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard
against that. The check for msi_enabled is not stricly neccessary.
This is part of XSA-157
Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
a) XEN_PCI_OP_enable_msi
b) XEN_PCI_OP_enable_msi
c) XEN_PCI_OP_disable_msi
results in hitting an BUG_ON condition in the msi.c code.
The MSI code uses an dev->msi_list to which it adds MSI entries.
Under the above conditions an BUG_ON() can be hit. The device
passed in the guest MUST have MSI capability.
The a) adds the entry to the dev->msi_list and sets msi_enabled.
The b) adds a second entry but adding in to SysFS fails (duplicate entry)
and deletes all of the entries from msi_list and returns (with msi_enabled
is still set). c) pci_disable_msi passes the msi_enabled checks and hits:
BUG_ON(list_empty(dev_to_msi_list(&dev->dev)));
and blows up.
The patch adds a simple check in the XEN_PCI_OP_enable_msi to guard
against that. The check for msix_enabled is not stricly neccessary.
This is part of XSA-157.
Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
For CONFIG_KALLSYMS, we keep two symbol tables and two string tables.
There's one full copy, marked SHF_ALLOC and laid out at the end of the
module's init section. There's also a cut-down version that only
contains core symbols and strings, and lives in the module's core
section.
After module init (and before we free the module memory), we switch
the mod->symtab, mod->num_symtab and mod->strtab to point to the core
versions. We do this under the module_mutex.
However, kallsyms doesn't take the module_mutex: it uses
preempt_disable() and rcu tricks to walk through the modules, because
it's used in the oops path. It's also used in /proc/kallsyms.
There's nothing atomic about the change of these variables, so we can
get the old (larger!) num_symtab and the new symtab pointer; in fact
this is what I saw when trying to reproduce.
By grouping these variables together, we can use a
carefully-dereferenced pointer to ensure we always get one or the
other (the free of the module init section is already done in an RCU
callback, so that's safe). We allocate the init one at the end of the
module init section, and keep the core one inside the struct module
itself (it could also have been allocated at the end of the module
core, but that's probably overkill).
[ Rebased for 4.4-stable and older, because the following changes aren't
in the older trees:
- e0224418516b4d8a6c2160574bac18447c354ef0: adds arg to is_core_symbol
- 7523e4dc5057e157212b4741abd6256e03404cf1: module_init/module_core/init_size/core_size
become init_layout.base/core_layout.base/init_layout.size/core_layout.size.
'This is because the pstore filesystem can be backed by UEFI variables,
and (for example) a crash might dump the last kilobytes of the dmesg
into a number of pstore entries, each entry backed by a separate UEFI
variable in the above GUID namespace, and with a variable name
according to the above pattern.
Please see "drivers/firmware/efi/efi-pstore.c".
While this patch series will not prevent the user from deleting those
UEFI variables via the pstore filesystem (i.e., deleting a pstore fs
entry will continue to delete the backing UEFI variable), I think it
would be nice to preserve the possibility for the sysadmin to delete
Linux-created UEFI variables that carry portions of the crash log,
*without* having to mount the pstore filesystem.'
There's also no chance of causing machines to become bricked by
deleting these variables, which is the whole purpose of excluding
things from the whitelist.
Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so
that we don't have to update the string in the future if new variable
name formats are created for crash dump variables.
Reported-by: Laszlo Ersek <lersek@redhat.com> Acked-by: Peter Jones <pjones@redhat.com> Tested-by: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
"rm -rf" is bricking some peoples' laptops because of variables being
used to store non-reinitializable firmware driver data that's required
to POST the hardware.
These are 100% bugs, and they need to be fixed, but in the mean time it
shouldn't be easy to *accidentally* brick machines.
We have to have delete working, and picking which variables do and don't
work for deletion is quite intractable, so instead make everything
immutable by default (except for a whitelist), and make tools that
aren't quite so broad-spectrum unset the immutable flag.
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
All the variables in this list so far are defined to be in the global
namespace in the UEFI spec, so this just further ensures we're
validating the variables we think we are.
Including the guid for entries will become more important in future
patches when we decide whether or not to allow deletion of variables
based on presence in this list.
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Actually translate from ucs2 to utf8 before doing the test, and then
test against our other utf8 data, instead of fudging it.
Signed-off-by: Peter Jones <pjones@redhat.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Translate EFI's UCS-2 variable names to UTF-8 instead of just assuming
all variable names fit in ASCII.
Signed-off-by: Peter Jones <pjones@redhat.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This adds ucs2_utf8size(), which tells us how big our ucs2 string is in
bytes, and ucs2_as_utf8, which translates from ucs2 to utf8..
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
As reported at https://bugs.launchpad.net/qemu/+bug/1494350,
it is possible to have vcpu->arch.st.last_steal initialized
from a thread other than vcpu thread, say the iothread, via
KVM_SET_MSRS.
Which can cause an overflow later (when subtracting from vcpu threads
sched_info.run_delay).
To avoid that, move steal time accumulation to vcpu entry time,
before copying steal time data to guest.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Reviewed-by: David Matlack <dmatlack@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since binutils 2.26 BFD is doing suffix merging on STRTAB sections. But
dedotify modifies the symbol names in place, which can also modify
unrelated symbols with a name that matches a suffix of a dotted name. To
remove the leading dot of a symbol name we can just increment the pointer
into the STRTAB section instead.
Backport to all stables to avoid breakage when people update their
binutils - mpe.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Acked-by: Avery Pennarun <apenwarr@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Beniamino reported that he was getting an RTM_NEWLINK message for a
given interface, after the RTM_DELLINK for it. It turns out that the
message is a wireless extensions message, which was sent because the
interface had been connected and disconnection while it was deleted
caused a wext message.
For its netlink messages, wext uses RTM_NEWLINK, but the message is
without all the regular rtnetlink attributes, so "ip monitor link"
prints just rudimentary information:
5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
link/ether
(from my hwsim reproduction)
This can cause userspace to get confused since it doesn't expect an
RTM_NEWLINK message after RTM_DELLINK.
The reason for this is that wext schedules a worker to send out the
messages, and the scheduling delay can cause the messages to get out
to userspace in different order.
To fix this, have wext register a netdevice notifier and flush out
any pending messages when netdevice state changes. This fixes any
ordering whenever the original message wasn't sent by a notifier
itself.
"MBC Mode", "VSS Mode", "VSS HPF Mode" and "Enhanced EQ Mode" ctls in
wm8958 codec driver are enum, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The DRC Mode like "AIF1DRC1 Mode" and EQ Mode like "AIF1.1 EQ Mode" in
wm8994 codec driver are enum ctls, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit f37755490fe9b ("tracepoints: Do not trace when cpu is offline") added
a check to make sure that tracepoints only get called when the cpu is
online, as it uses rcu_read_lock_sched() for protection.
Commit 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints
are disabled") added lockdep checks (including rcu checks) for events that
are not enabled to catch possible RCU issues that would only be triggered if
a trace event was enabled. Commit f37755490fe9b only stopped the warnings
when the trace event was enabled but did not prevent warnings if the trace
event was called when disabled.
To fix this, the cpu online check is moved to where the condition is added
to the trace event. This will place the cpu online check in all places that
it may be used now and in the future.
Fixes: f37755490fe9b ("tracepoints: Do not trace when cpu is offline") Fixes: 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints are disabled") Reported-by: Sudeep Holla <sudeep.holla@arm.com> Tested-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux guests on Haswell (and also SandyBridge and Broadwell, at least)
would crash if you decided to run a host command that uses PEBS, like
perf record -e 'cpu/mem-stores/pp' -a
This happens because KVM is using VMX MSR switching to disable PEBS, but
SDM [2015-12] 18.4.4.4 Re-configuring PEBS Facilities explains why it
isn't safe:
When software needs to reconfigure PEBS facilities, it should allow a
quiescent period between stopping the prior event counting and setting
up a new PEBS event. The quiescent period is to allow any latent
residual PEBS records to complete its capture at their previously
specified buffer address (provided by IA32_DS_AREA).
There might not be a quiescent period after the MSR switch, so a CPU
ends up using host's MSR_IA32_DS_AREA to access an area in guest's
memory. (Or MSR switching is just buggy on some models.)
The guest can learn something about the host this way:
If the guest doesn't map address pointed by MSR_IA32_DS_AREA, it results
in #PF where we leak host's MSR_IA32_DS_AREA through CR2.
After that, a malicious guest can map and configure memory where
MSR_IA32_DS_AREA is pointing and can therefore get an output from
host's tracing.
This is not a critical leak as the host must initiate with PEBS tracing
and I have not been able to get a record from more than one instruction
before vmentry in vmx_vcpu_run() (that place has most registers already
overwritten with guest's).
We could disable PEBS just few instructions before vmentry, but
disabling it earlier shouldn't affect host tracing too much.
We also don't need to switch MSR_IA32_PEBS_ENABLE on VMENTRY, but that
optimization isn't worth its code, IMO.
(If you are implementing PEBS for guests, be sure to handle the case
where both host and guest enable PEBS, because this patch doesn't.)
Fixes: 26a4f3c08de4 ("perf/x86: disable PEBS on a guest entry.") Reported-by: Jiří Olša <jolsa@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Avoid sending a partially initialised `siginfo_t' structure along SIGFPE
signals issued from `do_ov' and `do_trap_or_bp', leading to information
leaking from the kernel stack.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The Parrot NMEA GPS Flight Recorder is a USB composite device
consisting of hub, flash storage, and cp210x usb to serial chip.
It is an accessory to the mass-produced Parrot AR Drone 2.
The device emits standard NMEA messages which make the it compatible
with NMEA compatible software. It was tested using gpsd version 3.11-3
as an NMEA interpreter and using the official Parrot Flight Recorder.
The timer user status compat ioctl returned the bogus struct used for
64bit architectures instead of the 32bit one. This patch addresses
it to return the proper struct.
HDSPM driver contains a code issuing zero-division potentially in
system sample rate ctl code. This patch fixes it by not processing
a zero or invalid rate value as a divisor, as well as excluding the
invalid value to be passed via the given ctl element.
The OSS sequencer client tries to drain the pending events at
releasing. Unfortunately, as spotted by syzkaller fuzzer, this may
lead to an unkillable process state when the event has been queued at
the far future. Since the process being released can't be signaled
any longer, it remains and waits for the echo-back event in that far
future.
Back to history, the draining feature was implemented at the time we
misinterpreted POSIX definition for blocking file operation.
Actually, such a behavior is superfluous at release, and we should
just release the device as is instead of keeping it up forever.
This patch just removes the draining call that may block the release
for too long time unexpectedly.
X32 ABI takes the 64bit timespec, thus the timer user status ioctl becomes
incompatible with IA32. This results in NOTTY error when the ioctl is
issued.
Meanwhile, this struct in X32 is essentially identical with the one in
X86-64, so we can just bypassing to the existing code for this
specific compat ioctl.
Like the previous fixes for ctl and PCM, we need a fix for
incompatible X32 ABI regarding the rawmidi: namely, struct
snd_rawmidi_status has the timespec, and the size and the alignment on
X32 differ from IA32.
The X32 ABI takes the same alignment like x86-64, and this may result
in the incompatible struct size from ia32. Unfortunately, we hit this
in some control ABI: struct snd_ctl_elem_value differs between them
due to the position of 64bit variable array. This ends up with the
unknown ioctl (ENOTTY) error.
The fix is to add the compat entries for the new aligned struct.
When a directory is deleted, we don't take too much care about killing off
all the dirents that belong to it — on the basis that on remount, the scan
will conclude that the directory is dead anyway.
This doesn't work though, when the deleted directory contained a child
directory which was moved *out*. In the early stages of the fs build
we can then end up with an apparent hard link, with the child directory
appearing both in its true location, and as a child of the original
directory which are this stage of the mount process we don't *yet* know
is defunct.
To resolve this, take out the early special-casing of the "directories
shall not have hard links" rule in jffs2_build_inode_pass1(), and let the
normal nlink processing happen for directories as well as other inodes.
Then later in the build process we can set ic->pino_nlink to the parent
inode#, as is required for directories during normal operaton, instead
of the nlink. And complain only *then* about hard links which are still
in evidence even after killing off all the unreachable paths.
Reported-by: Liu Song <liu.song11@zte.com.cn> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
With this fix, all code paths should now be obtaining the page lock before
f->sem.
Reported-by: Szabó Tamás <sztomi89@gmail.com> Tested-by: Thomas Betker <thomas.betker@rohde-schwarz.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This reverts commit 5ffd3412ae55
("jffs2: Fix lock acquisition order bug in jffs2_write_begin").
The commit modified jffs2_write_begin() to remove a deadlock with
jffs2_garbage_collect_live(), but this introduced new deadlocks found
by multiple users. page_lock() actually has to be called before
mutex_lock(&c->alloc_sem) or mutex_lock(&f->sem) because
jffs2_write_end() and jffs2_readpage() are called with the page locked,
and they acquire c->alloc_sem and f->sem, resp.
In other words, the lock order in jffs2_write_begin() was correct, and
it is the jffs2_garbage_collect_live() path that has to be changed.
Revert the commit to get rid of the new deadlocks, and to clear the way
for a better fix of the original deadlock.
Reported-by: Deng Chao <deng.chao1@zte.com.cn> Reported-by: Ming Liu <liu.ming50@gmail.com> Reported-by: wangzaiwei <wangzaiwei@top-vision.cn> Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Pause/unpause graph tracing around do_suspend_lowlevel as it has
inconsistent call/return info after it jumps to the wakeup vector.
The graph trace buffer will otherwise become misaligned and
may eventually crash and hang on suspend.
To reproduce the issue and test the fix:
Run a function_graph trace over suspend/resume and set the graph
function to suspend_devices_and_enter. This consistently hangs the
system without this fix.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The id buffer in ata_device is a DMA target, but it isn't explicitly
cacheline aligned. Due to this, adjacent fields can be overwritten with
stale data from memory on non coherent architectures. As a result, the
kernel is sometimes unable to communicate with an ATA device.
Fix this by ensuring that the id buffer is cacheline aligned.
This issue is similar to that fixed by Commit 84bda12af31f
("libata: align ap->sector_buf").
As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.
I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.
The problems with this are:
* On big-endian machines, this will always write a zero because it
stores the wrong byte into user space.
* In compat mode, the upper three bytes of the variable are updated
by the compat_hdio_ioctl() function, but they now contain
uninitialized stack data.
* The hdparm tool calling this ioctl uses a 'static long' variable
to store the result. This means at least the upper bytes are
initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
would fill them with data that remains stale when the low byte
is overwritten. Fortunately libata doesn't implement any of the
affected ioctl commands, so this would only happen when we query
both an IDE and an ATA device in the same command such as
"hdparm -N -c /dev/hda /dev/sda"
* The libata code for unknown reasons started using ATA_IOC_GET_IO32
and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
while the ioctl commands that were added later use the normal
HDIO_* names. This is harmless but rather confusing.
This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reported-by: Soohoon Lee <Soohoon.Lee@f5.com> Tested-by: Soohoon Lee <Soohoon.Lee@f5.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
During DRAM initialization on certain ASpeed devices, an incorrect
bit (bit 10) was checked in the "SDRAM Bus Width Status" register
to determine DRAM width.
Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05.
The setup code for the performance counters in the AMD IOMMU driver
tests whether the counters can be written. It tests to setup a counter
for device 00:00.0, which fails on systems where this particular device
is not covered by the IOMMU.
Fix this by not relying on device 00:00.0 but only on the IOMMU being
present.
For interim responses we only need to parse a header and update
a number credits. Now it is done for all SMB2+ command except
SMB2_READ which is wrong. Fix this by adding such processing.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Tested-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When opening a file, SMB2_open() attempts to parse the lease state from the
SMB2 CREATE Response. However, the parsing code was not careful to ensure
that the create contexts are not empty or invalid, which can lead to out-
of-bounds memory access. This can be seen easily by trying
to read a file from a OSX 10.11 SMB3 server. Here is sample crash output:
The reference files use spaces to separate tokens, however, we must
preserve spaces inside string literals. Currently the only case in the
tree is struct edac_raw_error_desc in <linux/edac.h>:
$ KBUILD_SYMTYPES=1 make -s drivers/edac/amd64_edac.symtypes
$ mv drivers/edac/amd64_edac.{symtypes,symref}
$ KBUILD_SYMTYPES=1 make -s drivers/edac/amd64_edac.symtypes
drivers/edac/amd64_edac.c:527: warning: amd64_get_dram_hole_info: modversion changed because of changes in struct edac_raw_error_desc
Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently usb_port_resume waits for up to 2 seconds for CONNECT
status for SS devices only. This change will do the same thing for
non-SS devices even though the reason is a little different. This
will fix an issue where VBUS is turned off during system wide
"suspend to ram" and some 2.0 devices take greater than the current
max of 100ms to show connected after VBUS is enabled. This is most
commonly seen on hard drive based devices and USB3.0 devices plugged
into a 2.0 only port.
Signed-off-by: Al Cooper <alcooperx@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Add helper to access line-control register in order to work around a
cp2108 GET_LINE_CTL bug.
cp2108 GET_LINE_CTL returns the 16-bit value with the 2 bytes swapped.
However, SET_LINE_CTL functions properly. When the driver tries to modify
the register, it reads it, modifies some bits and writes back. Because the
read bytes were swapped, this often results in an invalid value to be
written. In turn, this causes cp2108 respond with a stall. The stall
sometimes doesn't clear properly and cp2108 starts responding to following
valid commands also with stalls, effectively failing.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message, modify probe error handling ] Signed-off-by: Johan Hovold <johan@kernel.org> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This change is preparation for implementing a cp2108 bug workaround.
The workaround requires storing some private data. Right now the data is
attached to the USB interface and allocated in the attach() callback.
The bug detection requires USB I/O which is done easier from port_probe()
callback rather than attach(). Since the USB access functions take port
as a parameter, and since the private data is used exclusively by these
functions, it can be allocated in port_probe(). Also, all cp210x devices
have exactly 1 port per USB iterface, so moving private data from the USB
interface to port is trivial.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Flush all device queues at close in order to work around a cp2108 Tx
queue bug.
Occasionally, writing data and immediately closing the port makes cp2108
stop responding. The device has to be unplugged to clear the error.
The failure is induced by shutting down the device while its Tx queue
still has unsent data. This condition is avoided by issuing PURGE command
from the close() callback.
This change is applied to all cp210x devices. Clearing internal queues on
close is generally good.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message ] Signed-off-by: Johan Hovold <johan@kernel.org> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.
To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.
Fixes: 712f4aad406bb1 ("unix: properly account for FDs passed over unix sockets") Reported-by: David Herrmann <dh.herrmann@gmail.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Michal Kubecek <mkubecek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It is possible for a process to allocate and accumulate far more FDs than
the process' limit by sending them over a unix socket then closing them
to keep the process' fd count low.
This change addresses this problem by keeping track of the number of FDs
in flight per user and preventing non-privileged processes from having
more FDs in flight than their configured FD limit.
Cc: Michal Kubecek <mkubecek@suse.com> Reported-by: socketpair@gmail.com Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Mitigates: CVE-2013-4312 (Linux 2.0+) Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a non-inherited ACL is set on a directory, nfsd will try to set the Posix
default ACL to NULL. This gets converted to "" by generic_setxattr().
As "" is not a valid posix acl attribute value, this results in an error.
So instead of setting the xattr to NULL, remove it.
Commit 35dc248383bbab0a7203fca4d722875bc81ef091 introduced a check for
current->mm to see if we have a user space context and only copies data
if we do. Now if an IO gets interrupted by a signal data isn't copied
into user space any more (as we don't have a user space context) but
user space isn't notified about it.
This patch modifies the behaviour to return -EINTR from bio_uncopy_user()
to notify userland that a signal has interrupted the syscall, otherwise
it could lead to a situation where the caller may get a buffer with
no data returned.
This can be reproduced by issuing SG_IO ioctl()s in one thread while
constantly sending signals to it.
[js] backport to 3.12
Fixes: 35dc248 [SCSI] sg: Fix user memory corruption when SG_IO is interrupted by a signal Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
I get the splat below when modprobing/rmmoding EDAC drivers. It happens
because bus->name is invalid after bus_unregister() has run. The Code: section
below corresponds to:
Dmitry reported that he was able to reproduce the WARN_ON_ONCE that
fires in locks_free_lock_context when the flc_posix list isn't empty.
The problem turns out to be that we're basically rebuilding the
file_lock from scratch in fcntl_setlk when we discover that the setlk
has raced with a close. If the l_whence field is SEEK_CUR or SEEK_END,
then we may end up with fl_start and fl_end values that differ from
when the lock was initially set, if the file position or length of the
file has changed in the interim.
Fix this by just reusing the same lock request structure, and simply
override fl_type value with F_UNLCK as appropriate. That ensures that
we really are unlocking the lock that was initially set.
While we're there, make sure that we do pop a WARN_ON_ONCE if the
removal ever fails. Also return -EBADF in this event, since that's
what we would have returned if the close had happened earlier.
Cc: Alexander Viro <viro@zeniv.linux.org.uk> Fixes: c293621bbf67 (stale POSIX lock handling) Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Acked-by: "J. Bruce Fields" <bfields@fieldses.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When we call pci_scan_root_bus we would pass in 'sd' (sysdata)
pointer which was an 'pcifront_sd' structure. However in the
pci_device_add it expects that the 'sd' is 'struct sysdata' and
sets the dev->node to what is in sd->node (offset 4):
That is an hole - filled with garbage as we used kmalloc instead of
kzalloc (the second problem).
This patch fixes the issue by:
1) Use kzalloc to initialize to a well known state.
2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That
way access to the 'node' will access the right offset.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
... into returning a positive to path_openat(), which would interpret that
as "symlink had been encountered" and proceed to corrupt memory, etc.
It can only happen due to a bug in some ->open() instance or in some LSM
hook, etc., so we report any such event *and* make sure it doesn't trick
us into further unpleasantness.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In __request_region, if a conflict with a BUSY and MUXED resource is
detected, then the caller goes to sleep and waits for the resource to be
released. A pointer on the conflicting resource is kept. At wake-up
this pointer is used as a parent to retry to request the region.
A first problem is that this pointer might well be invalid (if for
example the conflicting resource have already been freed). Another
problem is that the next call to __request_region() fails to detect a
remaining conflict. The previously conflicting resource is passed as a
parameter and __request_region() will look for a conflict among the
children of this resource and not at the resource itself. It is likely
to succeed anyway, even if there is still a conflict.
Instead, the parent of the conflicting resource should be passed to
__request_region().
As a fix, this patch doesn't update the parent resource pointer in the
case we have to wait for a muxed region right after.
Reported-and-tested-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Simon Guinot <simon.guinot@sequanux.org> Tested-by: Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The qword_get() function NUL-terminates its output buffer. If the input
string is in hex format \xXXXX... and the same length as the output
buffer, there is an off-by-one:
The ftrace:function event is only displayed for parsing the function tracer
data. It is not used to enable function tracing, and does not include an
"enable" file in its event directory.
Originally, this event was kept separate from other events because it did
not have a ->reg parameter. But perf added a "reg" parameter for its use
which caused issues, because it made the event available to functions where
it was not compatible for.
Commit 9b63776fa3ca9 "tracing: Do not enable function event with enable"
added a TRACE_EVENT_FL_IGNORE_ENABLE flag that prevented the function event
from being enabled by normal trace events. But this commit missed keeping
the function event from being displayed by the "available_events" directory,
which is used to show what events can be enabled by set_event.
One documented way to enable all events is to:
cat available_events > set_event
But because the function event is displayed in the available_events, this
now causes an INVALID error:
cat: write error: Invalid argument
Reported-by: Chunyu Hu <chuhu@redhat.com> Fixes: 9b63776fa3ca9 "tracing: Do not enable function event with enable" Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In async_pf we try to allocate with NOWAIT to get an element quickly
or fail. This code also handle failures gracefully. Lets silence
potential page allocation failures under load.
In the case where d_add_unique() finds an appropriate alias to use it will
have already incremented the reference count. An additional dget() to swap
the open context's dentry is unnecessary and will leak a reference.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Fixes: 275bb307865a3 ("NFSv4: Move dentry instantiation into the NFSv4-...") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
A Root Port's AER structure (rpc) contains a queue of events. aer_irq()
enqueues AER status information and schedules aer_isr() to dequeue and
process it. When we remove a device, aer_remove() waits for the queue to
be empty, then frees the rpc struct.
But aer_isr() references the rpc struct after dequeueing and possibly
emptying the queue, which can cause a use-after-free error as in the
following scenario with two threads, aer_isr() on the left and a
concurrent aer_remove() on the right:
Thread A Thread B
-------- --------
aer_irq():
rpc->prod_idx++
aer_remove():
wait_event(rpc->prod_idx == rpc->cons_idx)
# now blocked until queue becomes empty
aer_isr(): # ...
rpc->cons_idx++ # unblocked because queue is now empty
... kfree(rpc)
mutex_unlock(&rpc->rpc_mutex)
To prevent this problem, use flush_work() to wait until the last scheduled
instance of aer_isr() has completed before freeing the rpc struct in
aer_remove().
I reproduced this use-after-free by flashing a device FPGA and
re-enumerating the bus to find the new device. With SLUB debug, this
crashes with 0x6b bytes (POISON_FREE, the use-after-free magic number) in
GPR25:
The bulk of ATA host state machine is implemented by
ata_sff_hsm_move(). The function is called from either the interrupt
handler or, if polling, a work item. Unlike from the interrupt path,
the polling path calls the function without holding the host lock and
ata_sff_hsm_move() selectively grabs the lock.
This is completely broken. If an IRQ triggers while polling is in
progress, the two can easily race and end up accessing the hardware
and updating state machine state at the same time. This can put the
state machine in an illegal state and lead to a crash like the
following.
Fix it by ensuring that the polling path is holding the host lock
before entering ata_sff_hsm_move() so that all hardware accesses and
state updates are performed under the host lock.
The code within wait_event_interruptible() is called with
!TASK_RUNNING, so mustn't call any functions that can sleep,
like mutex_lock().
Since we re-check the list_empty() in a loop after the wait,
it's safe to simply use list_empty() without locking.
This bug has existed forever, but was only discovered now
because all userspace implementations, including the default
'rfkill' tool, use poll() or select() to get a readable fd
before attempting to read.
The contract between try_read() and try_write() is that when called
each processes as much data as possible. When instructed by osd_client
to skip a message, try_read() is violating this contract by returning
after receiving and discarding a single message instead of checking for
more. try_write() then gets a chance to write out more requests,
generating more replies/skips for try_read() to handle, forcing the
messenger into a starvation loop.
Reported-by: Varada Kari <Varada.Kari@sandisk.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Tested-by: Varada Kari <Varada.Kari@sandisk.com> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Per DP spec, the source device should fall back to 18 bpp, VESA range
RGB when the sink capability is unknown. Fix the color depth
clamping. 18 bpp color depth should ensure full color range in automatic
mode.
The clamping has been HDMI specific since its introduction in
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>. Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The value returned by sys_personality has type "long int".
It is saved to a variable of type "int", which is not a problem
yet because the type of task_struct->pesonality is "unsigned int".
The problem is the sign extension from "int" to "long int"
that happens on return from sys_sparc64_personality.
For example, a userspace call personality((unsigned) -EINVAL) will
result to any subsequent personality call, including absolutely
harmless read-only personality(0xffffffff) call, failing with
errno set to EINVAL.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
EDAC workqueue destruction is really fragile. We cancel delayed work
but if it is still running and requeues itself, we still go ahead and
destroy the workqueue and the queued work explodes when workqueue core
attempts to run it.
Make the destruction more robust by switching op_state to offline so
that requeuing stops. Cancel any pending work *synchronously* too.
commit 4956e10903fd ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Fixes: 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik...") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
sdhci has a legacy facility to prevent runtime suspend if the
bus power is on. This is needed in cases where the power to
the card is dependent on the bus power. It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off(). These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem. In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume. So remove the check.
The posix_clock_poll function is supposed to return a bit mask of
POLLxxx values. However, in case the hardware has disappeared (due to
hot plugging for example) this code returns -ENODEV in a futile
attempt to throw an error at the file descriptor level. The kernel's
file_operations interface does not accept such error codes from the
poll method. Instead, this function aught to return POLLERR.
The value -ENODEV does, in fact, contain the POLLERR bit (and almost
all the other POLLxxx bits as well), but only by chance. This patch
fixes code to return a proper bit mask.
Credit goes to Markus Elfring for pointing out the suspicious
signed/unsigned mismatch.
Reported-by: Markus Elfring <elfring@users.sourceforge.net>
igned-off-by: Richard Cochran <richardcochran@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Julia Lawall <julia.lawall@lip6.fr> Link: http://lkml.kernel.org/r/1450819198-17420-1-git-send-email-richardcochran@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When there is an error copying a chunk dm-snapshot can incorrectly hold
associated bios indefinitely, resulting in hung IO.
The function copy_callback sets pe->error if there was error copying the
chunk, and then calls complete_exception. complete_exception calls
pending_complete on error, otherwise it calls commit_exception with
commit_callback (and commit_callback calls complete_exception).
The persistent exception store (dm-snap-persistent.c) assumes that calls
to prepare_exception and commit_exception are paired.
persistent_prepare_exception increases ps->pending_count and
persistent_commit_exception decreases it.
If there is a copy error, persistent_prepare_exception is called but
persistent_commit_exception is not. This results in the variable
ps->pending_count never returning to zero and that causes some pending
exceptions (and their associated bios) to be held forever.
Fix this by unconditionally calling commit_exception regardless of
whether the copy was successful. A new "valid" parameter is added to
commit_exception -- when the copy fails this parameter is set to zero so
that the chunk that failed to copy (and all following chunks) is not
recorded in the snapshot store. Also, remove commit_callback now that
it is merely a wrapper around pending_complete.
Fixes: 50dd842ad ("dm space map metadata: fix ref counting bug when bootstrapping a new space map") Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The tda1004x was updating the properties cache before locking.
If the device is not locked, the data at the registers are just
random values with no real meaning.
This caused the driver to fail with libdvbv5, as such library
calls GET_PROPERTY from time to time, in order to return the
DVB stats.
Tested with a saa7134 card 78:
ASUSTeK P7131 Dual, vendor PCI ID: 1043:4862
v4l2-compliance sends a zeroed struct v4l2_streamparm in
v4l2-test-formats.cpp::testParmType(), and this results in a division by
0 in some gspca subdrivers:
Let's also get rid of the "cosmic ray protection" while we're at it.
Fixes: e9193059b1b3 "hostfs: fix races in dentry_name() and inode_name()" Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The channel checks the specified length and the provided amount of
data for CCWs and provides an incorrect length error if the size does
not match. Under z/VM with simulation activated the length may get
changed. Having the suppress length indication bit set is stated as
good CCW coding practice and avoids errors under z/VM.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We weren't accounting for the insertion of an inline extent item for the
symlink inode nor that we need to update the parent inode item (through
the call to btrfs_add_nondir()). So fix this by including two more
transaction units.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>