The NFCR register for MTU5 is at 0x1a95 offset according to Datasheet
Page 725, Table 16.4. The address of all registers is offset by 0x1200,
making the proper address of MTU5 NFCR register be 0x895.
Cc: stable@vger.kernel.org Fixes: 654c293e1687 ("mfd: Add Renesas RZ/G2L MTU3a core driver") Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20250910175914.12956-1-cosmin-gabriel.tanislav.xa@renesas.com Signed-off-by: Lee Jones <lee@kernel.org>
mfd: max77705: Setup the core driver as an interrupt controller
Current implementation describes only MFD's own topsys interrupts.
However, max77705 has a register which indicates interrupt source, i.e.
it acts as an interrupt controller. There's 4 interrupt sources in
max77705: topsys, charger, fuelgauge, usb type-c manager.
Setup max77705 MFD parent as an interrupt controller. Delete topsys
interrupts because currently unused.
Remove shared interrupt flag, because we're are an interrupt controller
now, and subdevices should request interrupts from us.
Charles Keepax [Wed, 3 Sep 2025 09:45:48 +0000 (10:45 +0100)]
mfd: cs42l43: Move IRQ enable/disable to encompass force suspend
As pm_runtime_force_suspend() will force the device state to suspend,
the driver needs to ensure no IRQ handlers are currently running. If not
those handlers may find they are now running on suspended hardware
despite holding a PM runtime reference. disable_irq() will sync any
currently running handlers, so move the IRQ disabling to cover the whole
of the forced suspend state to avoid such race conditions.
mfd: ls2kbmc: Add Loongson-2K BMC reset function support
Since the display is a sub-function of the Loongson-2K BMC, when the
BMC reset, the entire BMC PCIe is disconnected, including the display
which is interrupted.
Quick overview of the entire LS2K BMC reset process:
There are two types of reset methods: soft reset (BMC-initiated reboot
of IPMI reset command) and BMC watchdog reset (watchdog timeout).
First, regardless of the method, an interrupt is generated (PCIe interrupt
for soft reset/GPIO interrupt for watchdog reset);
Second, during the interrupt process, the system enters bmc_reset_work,
clears the bus/IO/mem resources of the LS7A PCI-E bridge, waits for the BMC
reset to begin, then restores the parent device's PCI configuration space,
waits for the BMC reset to complete, and finally restores the BMC PCI
configuration space.
Alexander Kurz [Fri, 29 Aug 2025 20:15:15 +0000 (20:15 +0000)]
dt-bindings: mfd: fsl,mc13xxx: Convert txt to DT schema
Convert the txt mc13xxx bindings to DT schema attempting to keep most
information. The nodes codec and touchscreen are not part of the new
schema since it was only briefly mentioned before.
Following the convention, rename led-control to fsl,led-control.
Janne Grunau [Thu, 28 Aug 2025 14:01:37 +0000 (16:01 +0200)]
mfd: macsmc: Add "apple,t8103-smc" compatible
After discussion with the devicetree maintainers we agreed to not extend
lists with the generic compatible "apple,smc" anymore [1]. Use
"apple,t8103-smc" as base compatible as it is the SoC the driver and
bindings were written for.
mfd: core: Increment of_node's refcount before linking it to the platform device
When an MFD device is added, a platform_device is allocated. If this
device is linked to a DT description, the corresponding OF node is linked
to the new platform device but the OF node's refcount isn't incremented.
As of_node_put() is called during the platform device release, it leads
to a refcount underflow.
Call of_node_get() to increment the OF node's refcount when the node is
linked to the newly created platform device.
dt-bindings: mfd: syscon: Document the control-scb syscon on PolarFire SoC
The "control-scb" region, contains the "tvs" temperature and voltage
sensors and the control/status registers for the system controller's
mailbox. The mailbox has a dedicated node, so there's no need for a
child node describing it, looking the syscon up by compatible is
sufficient.
Alex Elder [Mon, 25 Aug 2025 17:20:51 +0000 (12:20 -0500)]
mfd: simple-mfd-i2c: Add SpacemiT P1 support
Enable support for the RTC and regulators found in the SpacemiT P1
PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This
PMIC provides 6 buck converters and 12 LDO regulators. It also
implements a switch, watchdog timer, real-time clock, and more.
Initially its RTC and regulators are supported.
The Kontron SMARC-sAM67 module features an on-board house keeping uC.
It's designed to be compatible with the older on-board CPLD used on the
SMARC-sAL28 board. To be prepared for any board specific quirks, add a
specific compatible.
Arnd Bergmann [Fri, 8 Aug 2025 15:17:58 +0000 (17:17 +0200)]
mfd: aat2870: Add GPIOLIB_LEGACY dependency
This driver uses the legacy gpiolib interfaces to get gpio
numbers from platform data. There are no in-tree users of
this driver, so nothing defines the platform data.
Add a dependency on GPIOLIB_LEGACY for the moment to avoid the build
failure, and make sure the sound driver does not get built without the
mfd portion either pass that dependency along.
Alternatively, we could remove the mfd driver along with the backlight
and regulator portions.
Arnd Bergmann [Fri, 8 Aug 2025 15:17:57 +0000 (17:17 +0200)]
mfd: si476x: Add GPIOLIB_LEGACY dependency
This driver uses the legacy gpiolib interfaces to get gpio
numbers from platform data:
drivers/mfd/si476x-i2c.c: In function 'si476x_core_start':
drivers/mfd/si476x-i2c.c:133:21: error: implicit declaration of function 'gpio_is_valid'; did you mean 'uuid_is_valid'? [-Werror=implicit-function-declaration]
133 | if (gpio_is_valid(core->gpio_reset))
There are no in-tree users of this driver, so nothing defines
the platform data.
Add a dependency on GPIOLIB_LEGACY for the moment to avoid the build
failure, and make sure the sound driver does not get built without the
mfd portion either pass that dependency along.
Alternatively, we could remove the mfd driver along with the radio and
sound portions.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202507231653.UFlH2dMO-lkp@intel.com/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20250808151822.536879-14-arnd@kernel.org Signed-off-by: Lee Jones <lee@kernel.org>
dt-bindings: mfd: Move embedded controllers to own directory
Move several embedded controller bindings (like ChromeOS EC, Gateworks
System Controller and Kontron sl28cpld Board Management) to new
subdirectory "embedded-controller" matching their purpose.
An embedded controller (EC) is a discrete component that contains a
microcontroller (i.e. a small CPU running a small firmware without
operating system) mounted into a larger computer system running
a fully fledged operating system that needs to utilize the embedded
controller as part of its operation.
So far the EC bindings were split between "mfd" and "platform"
directory. MFD name comes from Linux, not hardware, and "platform" is a
bit too generic.
Rename Gateworks GSC and Huawei Gaokun filenames to match compatible, as
preferred for bindings.
Acked-by: Michael Walle <mwalle@kernel.org> # for sl28cpld Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Mark Brown <broonie@kernel.org> Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org> Link: https://lore.kernel.org/r/20250825081201.9775-2-krzysztof.kozlowski@linaro.org Signed-off-by: Lee Jones <lee@kernel.org>
Arnd Bergmann [Fri, 8 Aug 2025 15:17:56 +0000 (17:17 +0200)]
mfd: arizona: Make legacy gpiolib interface optional
The only machine that still uses the old gpio number based interface
is the wlf_cragg_6410 board file. In order to remove the dependency
on the interfaces, add #ifdef blocks here.
dt-bindings: mfd: aspeed-lpc: Add missing "clocks" property on lpc-snoop node
The ASpeed lpc-snoop nodes have a "clocks" property which isn't
documented. It looks like all the LPC child devices have the same clock
source. Perhaps it is the parent device that should have the clock, but
it's too late for that. The driver for lpc-snoop requires a clock to be
present.
Arnd Bergmann [Thu, 7 Aug 2025 07:19:28 +0000 (09:19 +0200)]
mfd: madera: Work around false-positive -Wininitialized warning
clang-21 warns about one uninitialized variable getting dereferenced
in madera_dev_init:
drivers/mfd/madera-core.c:739:10: error: variable 'mfd_devs' is uninitialized when used here [-Werror,-Wuninitialized]
739 | mfd_devs, n_devs,
| ^~~~~~~~
drivers/mfd/madera-core.c:459:33: note: initialize the variable 'mfd_devs' to silence this warning
459 | const struct mfd_cell *mfd_devs;
| ^
| = NULL
The code is actually correct here because n_devs is only nonzero
when mfd_devs is a valid pointer, but this is impossible for the
compiler to see reliably.
Change the logic to check for the pointer as well, to make this easier
for the compiler to follow.
Waqar Hameed [Tue, 5 Aug 2025 09:33:34 +0000 (11:33 +0200)]
mfd: macsmc: Remove error prints for devm_add_action_or_reset()
When `devm_add_action_or_reset()` fails, it is due to a failed memory
allocation and will thus return `-ENOMEM`. `dev_err_probe()` doesn't do
anything when error is `-ENOMEM`. Therefore, remove the useless call to
`dev_err_probe()` when `devm_add_action_or_reset()` fails, and just
return the value instead.
Jens Kehne [Mon, 4 Aug 2025 13:37:54 +0000 (15:37 +0200)]
mfd: da9063: Split chip variant reading in two bus transactions
We observed the initial probe of the da9063 failing in
da9063_get_device_type in about 30% of boots on a Xilinx ZynqMP based
board. The problem originates in da9063_i2c_blockreg_read, which uses
a single bus transaction to turn the register page and then read a
register. On the bus, this should translate to a write to register 0,
followed by a read to the target register, separated by a repeated
start. However, we found that after the write to register 0, the
controller sometimes continues directly with the register address of
the read request, without sending the chip address or a repeated start
in between, which makes the read request invalid.
To fix this, separate turning the page and reading the register into
two separate transactions. This brings the initialization code in line
with the rest of the driver, which uses register maps (which to my
knowledge do not use repeated starts after turning the page). This has
been included in our kernel for several months and was recently
included in a shipped product. For us, it reliably fixes the issue,
and we have not observed any new issues.
While the underlying problem is probably with the i2c controller or
its driver, I still propose a change here in the interest of
robustness: First, I'm not sure this issue can be fixed on the
controller side, since there are other issues related to repeated
start which can't (AR# 60695, AR# 61664). Second, similar problems
might exist with other controllers.
Hans de Goede [Mon, 4 Aug 2025 13:32:40 +0000 (15:32 +0200)]
mfd: intel_soc_pmic_chtdc_ti: Set use_single_read regmap_config flag
Testing has shown that reading multiple registers at once (for 10-bit
ADC values) does not work. Set the use_single_read regmap_config flag
to make regmap split these for us.
This should fix temperature opregion accesses done by
drivers/acpi/pmic/intel_pmic_chtdc_ti.c and is also necessary for
the upcoming drivers for the ADC and battery MFD cells.
Fixes: 6bac0606fdba ("mfd: Add support for Cherry Trail Dollar Cove TI PMIC") Cc: stable@vger.kernel.org Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Hans de Goede <hansg@kernel.org> Link: https://lore.kernel.org/r/20250804133240.312383-1-hansg@kernel.org Signed-off-by: Lee Jones <lee@kernel.org>
Heiko Stuebner [Mon, 4 Aug 2025 13:07:25 +0000 (15:07 +0200)]
mfd: qnap-mcu: Convert to guard(mutex) in qnap_mcu_exec
guard() makes sure that the mutex gets unlocked when the function returns
and thus removes the need for unlock gotos or similar mechanisms and
therefore allows for a simpler function structure.
mfd: kempld: Switch back to earlier ->init() behavior
Commit 9e36775c22c7 ("mfd: kempld: Remove custom DMI matching code")
removes the ability to load the driver if no matching system DMI data
is found. Before this commit the driver could be loaded using
alternative methods such as ACPI or `force_device_id` in the absence
of a matching system DMI entry.
Restore this ability while keeping the refactored
`platform_device_info` table.
Add the TS233 compatible and affiliated driver data to qnap-mcu.
The TS233 is mostly similar to the TS433, except not having any of the
PCIe components, so there are only 2 drives.
The fan pwm-limits from the vendor-configuration also are the same
as for the ts433 variant.
Nuno Sá [Thu, 17 Jul 2025 14:51:34 +0000 (15:51 +0100)]
mfd: adp5585: Drop useless return statement
In adp5585_reset_ev_parse(), when parsing the
adi,reset-pulse-width-us property, we were returning in case it was
found and valid. No point in doing that as we'll be returning anyways
after the exiting the property scope. And it could actually lead to bugs
if new properties happen to added after this one.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/linux-gpio/c85604d9e077511b8aa6ee0786579594cc0103d4.camel@gmail.com/T/#ma25557bd06ccd2531dc9c85ba6be74af781b81aa Signed-off-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20250717-adp5585-drop-ret-v1-1-2ae65bd780aa@analog.com Signed-off-by: Lee Jones <lee@kernel.org>
mfd: simple-mfd-i2c: Add compatible strings for Layerscape QIXIS FPGA
The QIXIS FPGA found on Layerscape boards such as LX2160AQDS, LS1028AQDS
etc deals with power-on-reset timing, muxing etc. Use the simple-mfd-i2c
as its core driver by adding its compatible string (already found in
some dt files). By using the simple-mfd-i2c driver, any child device
will have access to the i2c regmap created by it.
MAINTAINERS: Adjust file entry in LOONGSON SECURITY ENGINE DRIVERS
Commit 5c83b07df9c5 ("tpm: Add a driver for Loongson TPM device") adds a
driver at drivers/char/tpm/tpm_loongson.c, and commit 74fddd5fbab8
("MAINTAINERS: Add entry for Loongson Security Engine drivers") adds a new
section LOONGSON SECURITY ENGINE DRIVERS intending to refer to that driver.
It however adds the entry drivers/char/tpm_loongson.c; note that it misses
the tpm subdirectory.
Adjust the entry to refer to the intended file.
Fixes: 74fddd5fbab8 ("MAINTAINERS: Add entry for Loongson Security Engine drivers") Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com> Signed-off-by: Lee Jones <lee@kernel.org>
tpm: loongson: Add bufsiz parameter to tpm_loongson_send()
Commit 5c83b07df9c5 ("tpm: Add a driver for Loongson TPM device") has a
semantic conflict with commit 07d8004d6fb9 ("tpm: add bufsiz parameter
in the .send callback"), as the former change was developed against a
tree without the latter change. This results in a build error:
drivers/char/tpm/tpm_loongson.c:48:17: error: initialization of 'int (*)(struct tpm_chip *, u8 *, size_t, size_t)' {aka 'int (*)(struct tpm_chip *, unsigned char *, long unsigned int, long unsigned int)'} from incompatible pointer type 'int (*)(struct tpm_chip *, u8 *, size_t)' {aka 'int (*)(struct tpm_chip *, unsigned char *, long unsigned int)'} [-Wincompatible-pointer-types]
48 | .send = tpm_loongson_send,
| ^~~~~~~~~~~~~~~~~
drivers/char/tpm/tpm_loongson.c:48:17: note: (near initialization for 'tpm_loongson_ops.send')
drivers/char/tpm/tpm_loongson.c:31:12: note: 'tpm_loongson_send' declared here
31 | static int tpm_loongson_send(struct tpm_chip *chip, u8 *buf, size_t count)
| ^~~~~~~~~~~~~~~~~
Add the expected bufsiz parameter to tpm_loongson_send() to resolve the
error.
Fixes: 5c83b07df9c5 ("tpm: Add a driver for Loongson TPM device") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Lee Jones <lee@kernel.org>
Add driver for Maxim Integrated MAX7360 GPIO/GPO controller.
Two sets of GPIOs are provided by the device:
- Up to 8 GPIOs, shared with the PWM and rotary encoder functionalities.
These GPIOs also provide interrupts on input changes.
- Up to 6 GPOs, on unused keypad columns pins.
Co-developed-by: Kamel Bouhara <kamel.bouhara@bootlin.com> Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com> Link: https://lore.kernel.org/r/20250824-mdb-max7360-support-v14-7-435cfda2b1ea@bootlin.com Signed-off-by: Lee Jones <lee@kernel.org>
Ming Yu [Fri, 12 Sep 2025 09:19:46 +0000 (17:19 +0800)]
mfd: Add core driver for Nuvoton NCT6694
The Nuvoton NCT6694 provides an USB interface to the host to
access its features.
Sub-devices can use the USB functions nct6694_read_msg() and
nct6694_write_msg() to issue a command. They can also request
interrupt that will be called when the USB device receives its
interrupt pipe.
After a recent change that started using FIELD_GET() in tps6594-core.c,
there is an error when bitfield.h is not implicitly included, such as
when building allmodconfig for ARCH=hexagon:
drivers/mfd/tps6594-core.c:767:7: error: call to undeclared function 'FIELD_GET'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
767 | if (FIELD_GET(TPS65224_MASK_EN_PB_VSENSE_CONFIG, pwr_on) == TPS65224_EN_SEL_PB ||
| ^
Explicitly include bitfield.h to resolve the errors.
Reported-by: kernel test robot <lkp@intel.com> Fixes: d766ca01c208 ("mfd: tps6594: Add power button functionality") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Michael Walle <mwalle@kernel.org> Closes: https://lore.kernel.org/oe-kbuild-all/202509032356.LGa5hygM-lkp@intel.com/ Link: https://lore.kernel.org/r/20250904-mfd-tps6594-core-fix-bitfield-h-v1-1-5d0f00cfe58f@kernel.org Signed-off-by: Lee Jones <lee@kernel.org>
Add support for the boost regulator found in the Texas Instruments
BQ25703. The boost regulator is capable of outputting between 4.48
and 20.8 volts and between 0 and 6.35 amps.
mc13xxx_irq_ack() got deprecated and became dead code with commit 10f9edaeaa30 ("mfd: mc13xxx: Use regmap irq framework for interrupts").
It should be safe to remove it now.
Signed-off-by: Alexander Kurz <akurz@blala.de> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input Link: https://lore.kernel.org/r/20250811064358.1659-1-akurz@blala.de Signed-off-by: Lee Jones <lee@kernel.org>
mfd: vexpress-sysreg: Check the return value of devm_gpiochip_add_data()
Commit 974cc7b93441 ("mfd: vexpress: Define the device as MFD cells")
removed the return value check from the call to gpiochip_add_data() (or
rather gpiochip_add() back then and later converted to devres) with no
explanation. This function however can still fail, so check the return
value and bail-out if it does.
Cc: stable@vger.kernel.org Fixes: 974cc7b93441 ("mfd: vexpress: Define the device as MFD cells") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20250811-gpio-mmio-mfd-conv-v1-1-68c5c958cf80@linaro.org Signed-off-by: Lee Jones <lee@kernel.org>
Michael Walle [Tue, 26 Aug 2025 13:46:31 +0000 (15:46 +0200)]
mfd: tps6594: Add board power-off support
Add a system level power-off handler if the "system-power-controller"
flag is set for this device in the device tree.
A power-off request is triggered by writing the TRIGGER_I2C_0 bit (which
is actually just a convention and really depends on the freely
programmable FSM).
Loongson Security Engine supports random number generation, hash,
symmetric encryption and asymmetric encryption. Based on these
encryption functions, TPM2 have been implemented in the Loongson
Security Engine firmware. This driver is responsible for copying data
into the memory visible to the firmware and receiving data from the
firmware.
Co-developed-by: Yinggang Gu <guyinggang@loongson.cn> Signed-off-by: Yinggang Gu <guyinggang@loongson.cn> Signed-off-by: Qunqin Zhao <zhaoqunqin@loongson.cn> Reviewed-by: Huacai Chen <chenhuacai@loongson.cn> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Link: https://lore.kernel.org/r/20250705072045.1067-4-zhaoqunqin@loongson.cn Signed-off-by: Lee Jones <lee@kernel.org>
Linus Torvalds [Sun, 10 Aug 2025 05:51:37 +0000 (08:51 +0300)]
Merge tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp fixes from Borislav Petkov:
- Remove an obsolete comment and fix spelling
* tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Remove obsolete comment from takedown_cpu()
smp: Fix spelling in on_each_cpu_cond_mask()'s doc-comment
Linus Torvalds [Sun, 10 Aug 2025 05:46:47 +0000 (08:46 +0300)]
Merge tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Fix a wrong ioremap size in mvebu-gicp
- Remove yet another compile-test case for a driver which needs an
additional dependency
- Fix a lock inversion scenario in the IRQ unit test suite
- Remove an impossible flag situation in gic-v5
- Do not iounmap resources in gic-v5 which are managed by devm
- Make sure stale, left-over interrupts in mvebu-gicp are cleared on
driver init
- Fix a reference counting mishap in msi-lib
- Fix a dereference-before-null-ptr-check case in the riscv-imsic
irqchip driver
* tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mvebu-gicp: Use resource_size() for ioremap()
irqchip: Build IMX_MU_MSI only on ARM
genirq/test: Resolve irq lock inversion warnings
irqchip/gic-v5: Remove IRQD_RESEND_WHEN_IN_PROGRESS for ITS IRQs
irqchip/gic-v5: iwb: Fix iounmap probe failure path
irqchip/mvebu-gicp: Clear pending interrupts on init
irqchip/msi-lib: Fix fwnode refcount in msi_lib_irq_domain_select()
irqchip/riscv-imsic: Don't dereference before NULL pointer check
Linus Torvalds [Sun, 10 Aug 2025 05:15:32 +0000 (08:15 +0300)]
Merge tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix an interrupt vector setup race which leads to a non-functioning
device
- Add new Intel CPU models *and* a family: 0x12. Finally. Yippie! :-)
* tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Plug vector setup race
x86/cpu: Add new Intel CPU model numbers for Wildcatlake and Novalake
Len Brown [Sun, 10 Aug 2025 01:08:26 +0000 (21:08 -0400)]
tools/power turbostat: version 2025.09.09
Probe and display L3 Cache topology
Add ability to average an added counter
(useful for pre-integrated "counters", such as Watts)
Break the limit of 64 built-in counters.
Assorted bug fixes and minor feature tweaks
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/
may be readable by all, but
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/current_freq_khz
may be readable only by root.
Non-root turbostat users see complaints in this scenario.
Fail probe of the interface if we can't read current_freq_khz.
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Original-patch-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 11 Jun 2025 06:50:26 +0000 (14:50 +0800)]
tools/power turbostat: Fix DMR support
Together with the RAPL MSRs, there are more MSRs gone on DMR, including
PLR (Perf Limit Reasons), and IRTL (Package cstate Interrupt Response
Time Limit) MSRs. The configurable TDP info should also be retrieved
from TPMI based Intel Speed Select Technology feature.
Remove the access of these MSRs for DMR. Improve the DMR platform
feature table to make it more readable at the same time.
Fixes: 83075bd59de2 ("tools/power turbostat: Add initial support for DMR") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
tools/power turbostat: add format "average" for external attributes
External atributes with format "raw" are not printed in summary lines
for nodes/packages (or with option -S). The new format "average"
behaves like "raw" but also adds the summary data
Signed-off-by: Michael Hebenstreit <michael.hebenstreit@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 12 Jul 2025 20:16:56 +0000 (16:16 -0400)]
tools/power turbostat: Support more than 64 built-in-counters
We have out-grown the ability to use a 64-bit memory location
to inventory every possible built-in counter.
Leverage the the CPU_SET(3) macros to break this barrier.
Also, break the Joules & Watts counters into two,
since we can no longer 'or' them together...
Linus Torvalds [Sat, 9 Aug 2025 15:12:23 +0000 (18:12 +0300)]
Merge tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fix from Greg KH:
"Here is a single revert of one of the previous patches that went in
the last tty/serial merge that is breaking userspace on some platforms
(specifically powerpc, probably a few others.)
It accidentially changed the ioctl values of some tty ioctls, which
breaks xorg.
The revert has been in linux-next all this week with no reported
issues"
* tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: vt: use _IO() to define ioctl numbers"
Linus Torvalds [Sat, 9 Aug 2025 05:47:28 +0000 (08:47 +0300)]
Merge tag 'block-6.17-20250808' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Yu:
- mddev null-ptr-dereference fix, by Erkun
- md-cluster fail to remove the faulty disk regression fix, by
Heming
- minor cleanup, by Li Nan and Jinchao
- mdadm lifetime regression fix reported by syzkaller, by Yu Kuai
- MD pull request via Christoph
- add support for getting the FDP featuee in fabrics passthru path
(Nitesh Shetty)
- add capability to connect to an administrative controller
(Kamaljit Singh)
- fix a leak on sgl setup error (Keith Busch)
- initialize discovery subsys after debugfs is initialized
(Mohamed Khalfella)
- fix various comment typos (Bjorn Helgaas)
- remove unneeded semicolons (Jiapeng Chong)
- nvmet debugfs ordering issue fix
- Fix UAF in the tag_set in zloop
- Ensure sbitmap shallow depth covers entire set
- Reduce lock roundtrips in io context lookup
- Move scheduler tags alloc/free out of elevator and freeze lock, to
fix some lockdep found issues
- Improve robustness of queue limits checking
- Fix a regression with IO priorities, if no io context exists
* tag 'block-6.17-20250808' of git://git.kernel.dk/linux: (26 commits)
lib/sbitmap: make sbitmap_get_shallow() internal
lib/sbitmap: convert shallow_depth from one word to the whole sbitmap
nvmet: exit debugfs after discovery subsystem exits
block, bfq: Reorder struct bfq_iocq_bfqq_data
md: make rdev_addable usable for rcu mode
md/raid1: remove struct pool_info and related code
md/raid1: change r1conf->r1bio_pool to a pointer type
block: ensure discard_granularity is zero when discard is not supported
zloop: fix KASAN use-after-free of tag set
block: Fix default IO priority if there is no IO context
nvme: fix various comment typos
nvme-auth: remove unneeded semicolon
nvme-pci: fix leak on sgl setup error
nvmet: initialize discovery subsys after debugfs is initialized
nvme: add capability to connect to an administrative controller
nvmet: add support for FDP in fabrics passthru path
md: rename recovery_cp to resync_offset
md/md-cluster: handle REMOVE message earlier
md: fix create on open mddev lifetime regression
block: fix potential deadlock while running nr_hw_queue update
...
projects / thirdparty / kernel / stable.git / log
