Javier Lopez [Mon, 1 Sep 2014 04:23:35 +0000 (00:23 -0400)]
tests: Add test_wpas_mesh test cases
This wpa_supplicant tests include basic tests for:
- Mesh scan
- Mesh group add/remove
- Mesh peer connected/disconnected
- Add/Set/Remove to test mesh mode network
- Open mesh connectivity test
- Secure mesh connectivity test
- no_auto_peer
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
[no_auto_peer test by: Javier Cardona <javier@cozybit.com> Signed-off-by: Javier Lopez <jlopex@gmail.com>
Jouni Malinen [Thu, 20 Nov 2014 14:25:00 +0000 (16:25 +0200)]
nl80211: Do not try to change STA capability on NL80211_CMD_SET_STATION
cfg80211 will reject any of these attributes regardless of whether the
values actually change or not when NL80211_CMD_SET_STATION is used for
something else than TDLS. This path is hit at least when setting up
mesh, so filter out the attributes from NL80211_CMD_SET_STATION to match
the rules in cfg80211.
Jouni Malinen [Wed, 19 Nov 2014 20:02:08 +0000 (22:02 +0200)]
tests: Fix regression in START line total count
The previous changes to enable stdin control broke the previous case of
showing the total number of test cases in the START lines. Fix that by
using a separate variable for the total number of test casess instead of
using length of the list of remaining test cases.
Rashmi Ramanna [Mon, 17 Nov 2014 10:37:24 +0000 (16:07 +0530)]
P2P: Do not change P2P state on GO Neg failure if it is P2P_SEARCH
Changing the P2P state to P2P_IDLE on GO Negotiation Failure would stop
the previously issued P2P_FIND operation without notifying the upper
layers. Leave the search operation running if in P2P_SEARCH state to
avoid unexpected behavior in case the upper layers issued a new P2P_FIND
while waiting for GO Negotiation to complete.
Kyeyoon Park [Sat, 1 Nov 2014 06:33:41 +0000 (23:33 -0700)]
AP: Add Neighbor Discovery snooping mechanism for Proxy ARP
This commit establishes the infrastructure, and handles the Neighbor
Solicitation and Neighbor Advertisement frames. This will be extended
in the future to handle other frames.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Kyeyoon Park [Thu, 6 Nov 2014 00:15:46 +0000 (16:15 -0800)]
AP: Extend the BSS bridge neighbor entry management to support IPv6
This allows adding/deleting an IPv6 neighbor entry to/from the bridge,
to which the BSS belongs. This commit adds the needed functionality in
driver_nl80211.c for the Linux bridge implementation. In theory, this
could be shared with multiple Linux driver interfaces, but for now, only
the main nl80211 interface is supported.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Jouni Malinen [Wed, 19 Nov 2014 00:03:39 +0000 (02:03 +0200)]
tests: Move parallel-vm.py test control to the host
This allows all VMs to be used at the end of a test sequence by
assigning test cases to VMs based on which VM is available for a new
test case rather than splitting the full task at the beginning and
potentially getting stuck with the last VM running long test cases for
significantly longer than another VM that gets shorter duration tests
assigned to it.
Jouni Malinen [Wed, 19 Nov 2014 00:01:27 +0000 (02:01 +0200)]
tests: Add run-tests.py -i to control execution from stdin
The new -i command line argument can be used to control test case
execution from stdin to run-tests.py and vm-run.sh. This can be used,
e.g., to run multiple repeated test sequences in a virtual machine
without havign to restart the VM between each iteration.
Jouni Malinen [Tue, 18 Nov 2014 22:41:45 +0000 (00:41 +0200)]
tests: Allow run-tests.py to be run from the vm directory
Some of the paths in run-tests.py are hardcoded and could not handle
tests/hwsim/vm as the working directory. Modify the design enough to
allow ../run-tests.py -L to be used from the vm directory.
Jouni Malinen [Tue, 18 Nov 2014 22:34:36 +0000 (00:34 +0200)]
tests: Make run-tests.py process test case selection arguments
This allows a list of matching test cases to be produced without having
to run the test cases. Previously, -L output included all defined test
cases regardless of what else was included on the command line.
Ilan Peer [Wed, 5 Nov 2014 08:50:34 +0000 (03:50 -0500)]
AP: Drop retransmitted auth/assoc/action frames
It is possible that a station device might miss an ACK for an
authentication, association, or action frame, and thus retransmit the
same frame although the frame is already being processed in the stack.
While the duplicated frame should really be dropped in the kernel or
firmware code where duplicate detection is implemented for data frames,
it is possible that pre-association cases are not fully addressed (which
is the case at least with mac80211 today) and the frame may be delivered
to upper layer stack.
In such a case, the local AP will process the retransmitted frame although
it has already handled the request, which might cause the station to get
confused and as a result disconnect from the AP, blacklist it, etc.
To avoid such a case, save the sequence control of the last processed
management frame and in case of retransmissions drop them.
This gets registered in tls_openssl.c from tls_init(), so there is no
need for EAP-pwd implementation to register explicitly. This avoids some
corner cases where OpenSSL resources do not get fully freed on exit.
Jouni Malinen [Sun, 16 Nov 2014 23:14:35 +0000 (01:14 +0200)]
DFS: Fix hostapd operation without hw_mode driver data
If DFS implementation was built in, some configurations with drivers
that do not provide mode information could end up dereferencing a NULL
pointer. Fix this by skipping DFS operations in such cases since not
having information about modes and channels means that hostapd could not
perform DFS anyway (i.e., either this is not a wireless driver or the
driver takes care of DFS internally).
Jouni Malinen [Sun, 16 Nov 2014 23:08:04 +0000 (01:08 +0200)]
Fix hostapd operation without hw_mode driver data
Commit 7f0303d5b0bb425f3e7318a7016b55ba9e67f9de ('hostapd: Verify VHT
160/80+80 MHz driver support') added couple of hapd->iface->current_mode
dereferences of which the one in hostapd_set_freq() can be hit with some
configuration files when using driver wrappers that do not have hw_mode
data, i.e., when current_mode is NULL. This could result in segmentation
fault when trying to use driver=wired. Fix this by checking that
current_mode is not NULL before dereferencing it to get vht_capab.
Johannes Berg [Wed, 22 Oct 2014 12:04:03 +0000 (08:04 -0400)]
WMM AC: Notify driver before sending DelTS
Switch the stop and sending DelTS to avoid sending data packets
for the session after the DelTS, which is otherwise possible.
This also helps the mac80211 implementation as it requires stopping the
traffic flow before sending the DelTS as it may modify the AC parameters
for the affected queue, and that may in turn affect management frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Moshe Benji [Wed, 22 Oct 2014 12:03:54 +0000 (08:03 -0400)]
WMM AC: Parse WMM IE on association
Initialize WMM AC data structures upon successful association
with an AP that publishes WMM support, and deinitialize the data
structure when the association is no longer valid.
Javier Lopez [Mon, 1 Sep 2014 04:23:33 +0000 (00:23 -0400)]
Add mesh_group_{add,remove} control interface commands
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.
The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Javier Lopez <jlopex@gmail.com>
Jason Mobarak [Mon, 1 Sep 2014 04:23:36 +0000 (00:23 -0400)]
mesh: Enable mesh HT mode
Add a new option "mesh_ht_mode" that specifies the HT mode for the
mesh, with this option on, mesh beacons, actions frames, and probe
responses with include the appropriate HT information elements.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>] Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
mesh: Add timer for SAE authentication in RSN mesh
Add timer to do SAE re-authentication with number of tries defined
by MESH_AUTH_RETRY and timeout defined by MESH_AUTH_TIMEOUT.
Ignoring the sending of reply message on "SAE confirm before commit"
to avoid "ping-pong" issues with other mesh nodes. This is obvious when
number of mesh nodes in MBSS reaching 6.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Bob Copeland <me@bobcopeland.com>
Bob Copeland [Mon, 1 Sep 2014 04:23:30 +0000 (00:23 -0400)]
SAE: Enhance AP implementation to handle auth for mesh interfaces
Add state transition logic to the SAE frame handling in order to more
fully implement the state machine from the IEEE 802.11 standard. Special
cases are needed for infrastructure BSS case to avoid unexpected
Authentication frame sequence by postponing transmission of the second
Authentication frame untile the STA sends its Confirm.
[original patch by: Thomas Pedersen <thomas@noack.us>] Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Jason Mobarak <x@jason.mobarak.name> Signed-off-by: Thomas Pedersen <thomas@noack.us>
New kernels in wiphy_suspend() will call cfg80211_leave_all() that will
eventually end up in cfg80211_stop_ap() unless wowlan_triggers were set.
For now, use the parameters from the station mode as-is. It may be
desirable to extend (or constraint) this in the future for specific AP
mode needs.
Jouni Malinen [Sun, 16 Nov 2014 13:40:02 +0000 (15:40 +0200)]
Suite B: Select EAPOL-Key integrity and key-wrap algorithms based on AKM
This adds support for AKM 00-0F-AC:11 to specify the integrity and
key-wrap algorithms for EAPOL-Key frames using the new design where
descriptor version is set to 0 and algorithms are determined based on
AKM.
Jouni Malinen [Sun, 16 Nov 2014 11:22:46 +0000 (13:22 +0200)]
Suite B: PMKID derivation for AKM 00-0F-AC:11
The new AKM uses a different mechanism of deriving the PMKID based on
KCK instead of PMK. hostapd was already doing this after the KCK had
been derived, but wpa_supplicant functionality needs to be moved from
processing of EAPOL-Key frame 1/4 to 3/4 to have the KCK available.
Jouni Malinen [Sun, 16 Nov 2014 11:20:51 +0000 (13:20 +0200)]
Suite B: Add AKM 00-0F-AC:11
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.
Jouni Malinen [Sat, 15 Nov 2014 10:56:02 +0000 (12:56 +0200)]
tests: Clear ignore_old_scan_res setting
This parameter was used in some of the NFC test cases to make scanning
more robust in case of changing AP configuration. However, the parameter
was not cleared anywhere, so it could have been left in use for other
test cases as well. To get more consistent behavior, clear the value
back to its default between test cases.
Jouni Malinen [Sat, 15 Nov 2014 10:35:10 +0000 (12:35 +0200)]
OpenSSL: Allow TLS v1.1 and v1.2 to be negotiated by default
Use SSLv23_method() to enable TLS version negotiation for any version
equal to or newer than 1.0. If the old behavior is needed as a
workaround for some broken authentication servers, it can be configured
with phase1="tls_disable_tlsv1_1=1 tls_disable_tlsv1_2=1".
Dmitry Shmidt [Wed, 5 Nov 2014 21:22:25 +0000 (13:22 -0800)]
Add CTRL-EVENT-SCAN-FAILED notification in case of scan failure
This is needed since the SCAN command with radio work returns before the
actual driver operation to trigger a scan has been executed and as such,
cannot return result of that operation.
Jouni Malinen [Fri, 14 Nov 2014 18:57:05 +0000 (20:57 +0200)]
Work around AP misbehavior on EAPOL-Key descriptor version
It looks like some APs are incorrectly selecting descriptor version 3
(AES-128-CMAC) for EAPOL-Key frames when version 2 (HMAC-SHA1) was
expected to be used. This is likely triggered by an attempt to negotiate
PMF with SHA1-based AKM.
Since AES-128-CMAC is considered stronger than HMAC-SHA1, allow the
incorrect, but stronger, option to be used in these cases to avoid
interoperability issues with deployed APs.
This issue shows up with "WPA: CCMP is used, but EAPOL-Key descriptor
version (3) is not 2" in debug log. With the new workaround, this issue
is ignored and "WPA: Interoperability workaround: allow incorrect
(should have been HMAC-SHA1), but stronger (is AES-128-CMAC), descriptor
version to be used" is written to the log.
Yanbo Li [Sun, 2 Nov 2014 09:46:35 +0000 (17:46 +0800)]
hostapd: Change drv_flags from unsigned int to u64
Some flag already using a bit larger than 32, so extend the hostapd
drv_flags type similarly to the earlier wpa_supplicant change to get the
full flag content.
Ilan Peer [Mon, 27 Oct 2014 14:00:57 +0000 (10:00 -0400)]
tests: Make vm-run.sh arguments non-positional
This was currently breaking parallel-run.*, as it was passing
--split num/num parameters (intended for rnu-tests.py)
to vm-run.sh which broke the --codecov and --timewrap options.
Ilan Peer [Mon, 27 Oct 2014 14:00:54 +0000 (10:00 -0400)]
tests: Add option to build before running all tests
Add an option --build to run-all.sh to build before starting to run all
the tests. In addition, add an option --codecov to extract the code
coverage data at the end of the run.
Jouni Malinen [Sat, 1 Nov 2014 14:15:53 +0000 (16:15 +0200)]
Remove references to madwifi from various files
Number of documentation and configuration files had references to the
madwifi driver interface that was removed in the previous commit. Remove
these references as well.
Jouni Malinen [Sat, 1 Nov 2014 14:13:41 +0000 (16:13 +0200)]
madwifi: Remove obsolete madwifi driver interface
The MadWifi project is not active anymore and the last release happened
in early 2008. As such, there is no remaining justification for
maintaining the madwifi-specific driver interface for hostapd either.
This helps window managers treat the window properly. Mostly tiling WMs
are affected by this. All other windows inherit this option from QDialog
already.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Sunil Dutt [Thu, 30 Oct 2014 15:21:52 +0000 (20:51 +0530)]
P2P: Do not consider the p2p_scan results after p2p_stop_find
If p2p_stop_find is issued after the p2p_scan request is triggered to
the host driver, the obtained scan results are also considered to update
the P2P peer entries. This is not always desired behavior, i.e., it can
be clearer if no P2P-DEVICE-FOUND events are generated based of that
final pending scan.
Sunil Dutt [Thu, 30 Oct 2014 12:07:46 +0000 (17:37 +0530)]
P2P: Delay scan operation only when P2P is not in search state
With the radio work interface in place, station interface SCAN command
was not scheduled (i.e., it got continously delayed with "Delay station
mode scan while P2P operation is in progress") when a p2p_find was
operational. Fix this be delaying station mode scan only when a P2P
operation is in progress, but not in search state.
Sunil Dutt [Thu, 30 Oct 2014 10:50:22 +0000 (16:20 +0530)]
P2P: Set p2p_scan_running based on driver scan request result
With the radio work interface, the actual request to start p2p_scan
operation is scheduled from a radio work and hence the initial return
value cannot provide the real result of the driver operation to trigger
a scan. Introduce a new notification API to indicate the scan trigger
status based on which the p2p_scan_running instance can be set using the
real return value from the driver operation.
Jouni Malinen [Thu, 30 Oct 2014 09:43:47 +0000 (11:43 +0200)]
MACsec: Fix policy configuration
macsec_validate variable was set incorrectly to FALSE(0) or TRUE(1)
instead of the enum validate_frames values (Disabled(0), Checked(1),
Strict(2). This ended up policy == SHOULD_SECURE to be mapped to
macsec_validate == Checked instead of Strict. This could have resulted
in unintended SecY forwarding of invalid packets rather than dropping
them.
Jouni Malinen [Wed, 29 Oct 2014 11:04:09 +0000 (13:04 +0200)]
P2P: Clean up p2p_go_neg_failed() calls
This function is always called with the peer argument equal to
p2p->go_neg_peer, so there is no need for that argument to be there. In
addition, p2p->go_neg_peer is not NULL in cases where there is an
ongoing GO Negotiation, so the function can be simplified to just check
once whether the peer pointer is set and if not, skip all processing.
Jouni Malinen [Tue, 28 Oct 2014 14:39:33 +0000 (16:39 +0200)]
tests: GO Negotiation and timeout while waiting for peer
grpform_cred_ready_timeout2 is similar to the grpform_cred_ready_timeout
test case with the difference being in initiating a P2P_FIND operation
during the wait.
Rashmi Ramanna [Tue, 28 Oct 2014 11:26:43 +0000 (16:56 +0530)]
P2P: Use timer to fail GO Negotation while waiting for peer
The timeout check while waiting for the peer to accept the GO
Negotiation depended on the WAIT_PEER_IDLE or WAIT_PEER_CONNECT states
being in use. Any P2P command to alter such states would have resulted
in the failure to time out GO Negotiation and thus ended up in not
indicating GO Negotiation failure or left the selected peer available
for new GO negotiation after the expected two minute timeout.
Fix this by using a separate timer to time out GO Negotiation
irrespective of the P2P state.
Jouni Malinen [Tue, 28 Oct 2014 12:01:16 +0000 (14:01 +0200)]
tests: Remove ap_ht40_csa and ap_ht40_csa3 workarounds
The issue in mac80211 was identified and proposed fix is now available,
so remove the workaround here and start reporting failures from
unexpected disconnection during CSA.
Jouni Malinen [Mon, 27 Oct 2014 23:47:17 +0000 (01:47 +0200)]
P2P: Do not call wpas_p2p_disconnect_safely() if no match is found
In theory, wpas_p2p_disconnect_safely() could have dereferenced the
wpa_s == NULL argument, but in practice, it won't due to the
calling_wpa_s == wpa_s check and wpas_p2p_disconnect() accepting NULL.
Anyway, it is cleaner to add an explicit check for this. (CID 74492)
Jouni Malinen [Mon, 27 Oct 2014 23:41:57 +0000 (01:41 +0200)]
nl80211: Fix a copy-paste error in key offload management
Commit b41f26845aaa7cf8aed6e4889e7041debc476ef9 ('Add support for
offloading key management operations to the driver') used incorrect
variable for determining the KCK length. This does not get triggered in
normal use cases since KCK and KEK are always included and of the same
length (in currently supported key management cases). Anyway, this needs
to be fixed to check the correct attribute. (CID 74491)
Kyeyoon Park [Fri, 26 Sep 2014 05:32:55 +0000 (22:32 -0700)]
AP: Add support for Proxy ARP, DHCP snooping mechanism
Proxy ARP allows the AP devices to keep track of the hardware address to
IP address mapping of the STA devices within the BSS. When a request for
such information is made (i.e., ARP request, Neighbor Solicitation), the
AP will respond on behalf of the STA device within the BSS. Such
requests could originate from a device within the BSS or also from the
bridge. In the process of the AP replying to the request (i.e., ARP
reply, Neighbor Advertisement), the AP will drop the original request
frame. The relevant STA will not even know that such information was
ever requested.
This feature is a requirement for Hotspot 2.0, and is defined in IEEE
Std 802.11-2012, 10.23.13. While the Proxy ARP support code mainly
resides in the kernel bridge code, in order to optimize the performance
and simplify kernel implementation, the DHCP snooping code was added to
the hostapd.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
projects / thirdparty / hostap.git / log
