The ice_adapter structure is used by the ice driver to connect multiple
physical functions of a device in software. It was introduced by
commit 0e2bddf9e5f9 ("ice: add ice_adapter for shared data across PFs on
the same NIC") and is primarily used for PTP support, as well as for
handling certain cross-PF synchronization.
The original design of ice_adapter used PCI address information to
determine which devices should be connected. This was extended to support
E825C devices by commit fdb7f54700b1 ("ice: Initial support for E825C
hardware in ice_adapter"), which used the device ID for E825C devices
instead of the PCI address.
Later, commit 0093cb194a75 ("ice: use DSN instead of PCI BDF for
ice_adapter index") replaced the use of Bus/Device/Function addressing with
use of the device serial number.
E825C devices may appear in "Dual NAC" configuration which has multiple
physical devices tied to the same clock source and which need to use the
same ice_adapter. Unfortunately, each "NAC" has its own NVM which has its
own unique Device Serial Number. Thus, use of the DSN for connecting
ice_adapter does not work properly. It "worked" in the pre-production
systems because the DSN was not initialized on the test NVMs and all the
NACs had the same zero'd serial number.
Since we cannot rely on the DSN, lets fall back to the logic in the
original E825C support which used the device ID. This is safe for E825C
only because of the embedded nature of the device. It isn't a discreet
adapter that can be plugged into an arbitrary system. All E825C devices on
a given system are connected to the same clock source and need to be
configured through the same PTP clock.
To make this separation clear, reserve bit 63 of the 64-bit index values as
a "fixed index" indicator. Always clear this bit when using the device
serial number as an index.
For E825C, use a fixed value defined as the 0x579C E825C backplane device
ID bitwise ORed with the fixed index indicator. This is slightly different
than the original logic of just using the device ID directly. Doing so
prevents a potential issue with systems where only one of the NACs is
connected with an external PHY over SGMII. In that case, one NAC would
have the E825C_SGMII device ID, but the other would not.
Separate the determination of the full 64-bit index from the 32-bit
reduction logic. Provide both ice_adapter_index() and a wrapping
ice_adapter_xa_index() which handles reducing the index to a long on 32-bit
systems. As before, cache the full index value in the adapter structure to
warn about collisions.
This fixes issues with E825C not initializing PTP on both NACs, due to
failure to connect the appropriate devices to the same ice_adapter.
Fixes: 0093cb194a75 ("ice: use DSN instead of PCI BDF for ice_adapter index") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ice_cfg_tx_topo function attempts to apply Tx scheduler topology
configuration based on NVM parameters, selecting either a 5 or 9 layer
topology.
As part of this flow, the driver acquires the "Global Configuration Lock",
which is a hardware resource associated with programming the DDP package
to the device. This "lock" is implemented by firmware as a way to
guarantee that only one PF can program the DDP for a device. Unlike a
traditional lock, once a PF has acquired this lock, no other PF will be
able to acquire it again (including that PF) until a CORER of the device.
Future requests to acquire the lock report that global configuration has
already completed.
The following flow is used to program the Tx topology:
* Read the DDP package for scheduler configuration data
* Acquire the global configuration lock
* Program Tx scheduler topology according to DDP package data
* Trigger a CORER which clears the global configuration lock
This is followed by the flow for programming the DDP package:
* Acquire the global configuration lock (again)
* Download the DDP package to the device
* Release the global configuration lock.
However, if configuration of the Tx topology fails, (i.e.
ice_get_set_tx_topo returns an error code), the driver exits
ice_cfg_tx_topo() immediately, and fails to trigger CORER.
While the global configuration lock is held, the firmware rejects most
AdminQ commands, as it is waiting for the DDP package download (or Tx
scheduler topology programming) to occur.
The current driver flows assume that the global configuration lock has been
reset by CORER after programming the Tx topology. Thus, the same PF
attempts to acquire the global lock again, and fails. This results in the
driver reporting "an unknown error occurred when loading the DDP package".
It then attempts to enter safe mode, but ultimately fails to finish
ice_probe() since nearly all AdminQ command report error codes, and the
driver stops loading the device at some point during its initialization.
The only currently known way that ice_get_set_tx_topo() can fail is with
certain older DDP packages which contain invalid topology configuration, on
firmware versions which strictly validate this data. The most recent
releases of the DDP have resolved the invalid data. However, it is still
poor practice to essentially brick the device, and prevent access to the
device even through safe mode or recovery mode. It is also plausible that
this command could fail for some other reason in the future.
We cannot simply release the global lock after a failed call to
ice_get_set_tx_topo(). Releasing the lock indicates to firmware that global
configuration (downloading of the DDP) has completed. Future attempts by
this or other PFs to load the DDP will fail with a report that the DDP
package has already been downloaded. Then, PFs will enter safe mode as they
realize that the package on the device does not meet the minimum version
requirement to load. The reported error messages are confusing, as they
indicate the version of the default "safe mode" package in the NVM, rather
than the version of the file loaded from /lib/firmware.
Instead, we need to trigger CORER to clear global configuration. This is
the lowest level of hardware reset which clears the global configuration
lock and related state. It also clears any already downloaded DDP.
Crucially, it does *not* clear the Tx scheduler topology configuration.
Refactor ice_cfg_tx_topo() to always trigger a CORER after acquiring the
global lock, regardless of success or failure of the topology
configuration.
We need to re-initialize the HW structure when we trigger the CORER. Thus,
it makes sense for this to be the responsibility of ice_cfg_tx_topo()
rather than its caller, ice_init_tx_topology(). This avoids needless
re-initialization in cases where we don't attempt to update the Tx
scheduler topology, such as if it has already been programmed.
There is one catch: failure to re-initialize the HW struct should stop
ice_probe(). If this function fails, we won't have a valid HW structure and
cannot ensure the device is functioning properly. To handle this, ensure
ice_cfg_tx_topo() returns a limited set of error codes. Set aside one
specifically, -ENODEV, to indicate that the ice_init_tx_topology() should
fail and stop probe.
Other error codes indicate failure to apply the Tx scheduler topology. This
is treated as a non-fatal error, with an informational message informing
the system administrator that the updated Tx topology did not apply. This
allows the device to load and function with the default Tx scheduler
topology, rather than failing to load entirely.
Note that this use of CORER will not result in loops with future PFs
attempting to also load the invalid Tx topology configuration. The first PF
will acquire the global configuration lock as part of programming the DDP.
Each PF after this will attempt to acquire the global lock as part of
programming the Tx topology, and will fail with the indication from
firmware that global configuration is already complete. Tx scheduler
topology configuration is only performed during driver init (probe or
devlink reload) and not during cleanup for a CORER that happens after probe
completes.
Fixes: 91427e6d9030 ("ice: Support 5 layer topology") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'tag' parameter is passed by value and is not actually used after
being incremented, so remove the increment. It's the function that calls
gm200_flcn_pio_imem_wr that is supposed to (and does) increment 'tag'.
Fixes: 0e44c2170876 ("drm/nouveau/flcn: new code to load+boot simple HS FWs (VPR scrubber)") Reviewed-by: Philipp Stanner <phasta@kernel.org> Signed-off-by: Timur Tabi <ttabi@nvidia.com> Link: https://lore.kernel.org/r/20250813001004.2986092-2-ttabi@nvidia.com Signed-off-by: Danilo Krummrich <dakr@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function set_name_sync() uses hdev->dev_name field to send
HCI_OP_WRITE_LOCAL_NAME command, but copying from data to hdev->dev_name
is called after mgmt cmd was queued, so it is possible that function
set_name_sync() will read old name value.
This change adds name as a parameter for function hci_update_name_sync()
to avoid race condition.
Fixes: 6f6ff38a1e14 ("Bluetooth: hci_sync: Convert MGMT_OP_SET_LOCAL_NAME") Signed-off-by: Pavel Shpakovskiy <pashpakovskii@salutedevices.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This attempts to detect if HCI_EV_NUM_COMP_PKTS contain an unbalanced
(more than currently considered outstanding) number of packets otherwise
it could cause the hcon->sent to underflow and loop around breaking the
tracking of the outstanding packets pending acknowledgment.
Fixes: f42809185896 ("Bluetooth: Simplify num_comp_pkts_evt function") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When suspending, the disconnect command for an active Bluetooth
connection could be issued, but the corresponding
`HCI_EV_DISCONN_COMPLETE` event might not be received before the system
completes the suspend process. This can lead to an inconsistent state.
On resume, the controller may auto-accept reconnections from the same
device (due to suspend event filters), but these new connections are
rejected by the kernel which still has connection objects from before
suspend. Resulting in errors like:
```
kernel: Bluetooth: hci0: ACL packet for unknown connection handle 1
kernel: Bluetooth: hci0: Ignoring HCI_Connection_Complete for existing
connection
```
This is a btmon snippet that shows the issue:
```
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 1 Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 2
Status: Success (0x00)
[...]
// Host suspends with the event filter set for the device
// On resume, the device tries to reconnect with a new handle
// Kernel ignores this event because there is an existing connection
with
// handle 1
```
By explicitly setting the connection state to BT_CLOSED we can ensure a
consistent state, even if we don't receive the disconnect complete event
in time.
Link: https://github.com/bluez/bluez/issues/1226 Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Ludovico de Nittis <ludovico.denittis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the host sends an HCI_OP_DISCONNECT command, the controller may
respond with the status HCI_ERROR_UNKNOWN_CONN_ID (0x02). E.g. this can
happen on resume from suspend, if the link was terminated by the remote
device before the event mask was correctly set.
This is a btmon snippet that shows the issue:
```
> ACL Data RX: Handle 3 flags 0x02 dlen 12
L2CAP: Disconnection Request (0x06) ident 5 len 4
Destination CID: 65
Source CID: 72
< ACL Data TX: Handle 3 flags 0x00 dlen 12
L2CAP: Disconnection Response (0x07) ident 5 len 4
Destination CID: 65
Source CID: 72
> ACL Data RX: Handle 3 flags 0x02 dlen 12
L2CAP: Disconnection Request (0x06) ident 6 len 4
Destination CID: 64
Source CID: 71
< ACL Data TX: Handle 3 flags 0x00 dlen 12
L2CAP: Disconnection Response (0x07) ident 6 len 4
Destination CID: 64
Source CID: 71
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0x3dbff807fffbffff
Inquiry Complete
Inquiry Result
Connection Complete
Connection Request
Disconnection Complete
Authentication Complete
[...]
< HCI Command: Disconnect (0x01|0x0006) plen 3
Handle: 3 Address: 78:20:A5:4A:DF:28 (Nintendo Co.,Ltd)
Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
Disconnect (0x01|0x0006) ncmd 1
Status: Unknown Connection Identifier (0x02)
```
Currently, the hci_cs_disconnect function treats any non-zero status
as a command failure. This can be misleading because the connection is
indeed being terminated and the controller is confirming that is has no
knowledge of that connection handle. Meaning that the initial request of
disconnecting a device should be treated as done.
With this change we allow the function to proceed, following the success
path, which correctly calls `mgmt_device_disconnected` and ensures a
consistent state.
Link: https://github.com/bluez/bluez/issues/1226 Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Signed-off-by: Ludovico de Nittis <ludovico.denittis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing a macb device, the driver calls phy_exit() before
unregister_netdev(). This leads to a WARN from kernfs:
------------[ cut here ]------------
kernfs: can not remove 'attached_dev', no directory
WARNING: CPU: 1 PID: 27146 at fs/kernfs/dir.c:1683
Call trace:
kernfs_remove_by_name_ns+0xd8/0xf0
sysfs_remove_link+0x24/0x58
phy_detach+0x5c/0x168
phy_disconnect+0x4c/0x70
phylink_disconnect_phy+0x6c/0xc0 [phylink]
macb_close+0x6c/0x170 [macb]
...
macb_remove+0x60/0x168 [macb]
platform_remove+0x5c/0x80
...
The warning happens because the PHY is being exited while the netdev
is still registered. The correct order is to unregister the netdev
before shutting down the PHY and cleaning up the MDIO bus.
Fix this by moving unregister_netdev() ahead of phy_exit() in
macb_remove().
Previously, the battery status (charging/discharging) was not reported
immediately to user-space.
For most input devices, this wasn't problematic because changing their
battery status requires connecting them to a different bus.
For example, a gamepad would report a discharging status while
connected via Bluetooth and a charging status while connected via USB.
However, certain devices are not connected or disconnected when their
battery status changes. For example, a phone battery changes its status
without connecting or disconnecting it.
In these cases, the battery status was not reported immediately to user
space.
Report battery status changes immediately to user space to support
these kinds of devices.
In preparation for a patch fixing a bug affecting
hidinput_set_battery_charge_status(), rename the function to
hidinput_update_battery_charge_status() and move it up so it can be used
by hidinput_update_battery().
When compiling for pseries or powernv defconfig with "make C=1",
these warning were reported bu sparse tool in powerpc/kernel/kvm.c
arch/powerpc/kernel/kvm.c:635:9: warning: switch with no cases
arch/powerpc/kernel/kvm.c:646:9: warning: switch with no cases
Currently #ifdef were added after the switch case which are specific
for BOOKE and PPC_BOOK3S_32. These are not enabled in pseries/powernv
defconfig. Fix it by moving the #ifdef before switch(){}
Introduce error handling to address an issue where, after a hotplug
event, the cursor continues to update. This situation can lead to a
kernel panic due to accessing the NULL `old_state->crtc`.
Adding NULL pointer checks to ensure stability by preventing operations
on an invalid CRTC state.
Fixes: d208261e9f7c ("drm/mediatek: Add wait_event_timeout when disabling plane") Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: CK Hu <ck.hu@mediatek.com> Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20250728025036.24953-1-jason-jh.lin@mediatek.com/ Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the high bitfield of certain DSI registers
do not align with the configuration of the SWI registers
description. This can lead to wrong programming these DSI
registers, for example for 4k resloution where H_TOTAL is
taking 13 bits but software is programming only 12 bits
because of the incorrect bitmask for H_TOTAL bitfeild,
this is causing DSI FIFO errors. To resolve this issue,
increase the high bitfield of the DSI registers from 12 bits
to 16 bits in dsi.xml to match the SWI register configuration.
Various parts of the display driver can be triggering the display
snapshot (including the IOMMU fault handlers). Move the call to
msm_disp_snapshot_init() before KMS initialization, otherwise it is
possible to ocassionally trigger the kernel fault during init:
Restructure the call site for dma_contiguous_early_fixup() to
where the reserved_mem nodes are being parsed from the DT so that
dma_mmu_remap[] is populated before dma_contiguous_remap() is called.
Fixes: 8a6e02d0c00e ("of: reserved_mem: Restructure how the reserved memory regions are processed") Signed-off-by: Oreoluwa Babatunde <oreoluwa.babatunde@oss.qualcomm.com> Tested-by: William Zhang <william.zhang@broadcom.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20250806172421.2748302-1-oreoluwa.babatunde@oss.qualcomm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 9e30ecf23b1b ("net: ipv4: fix incorrect MTU in broadcast routes")
introduced a regression where local-broadcast packets would have their
gateway set in __mkroute_output, which was caused by fi = NULL being
removed.
Fix this by resetting the fib_info for local-broadcast packets. This
preserves the intended changes for directed-broadcast packets.
Cc: stable@vger.kernel.org Fixes: 9e30ecf23b1b ("net: ipv4: fix incorrect MTU in broadcast routes") Reported-by: Brett A C Sheffield <bacs@librecast.net> Closes: https://lore.kernel.org/regressions/20250822165231.4353-4-bacs@librecast.net Signed-off-by: Oscar Maes <oscmaes92@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250827062322.4807-1-oscmaes92@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When operating on struct vhost_net_ubuf_ref, the following execution
sequence is theoretically possible:
CPU0 is finalizing DMA operation CPU1 is doing VHOST_NET_SET_BACKEND
// ubufs->refcount == 2
vhost_net_ubuf_put() vhost_net_ubuf_put_wait_and_free(oldubufs)
vhost_net_ubuf_put_and_wait()
vhost_net_ubuf_put()
int r = atomic_sub_return(1, &ubufs->refcount);
// r = 1
int r = atomic_sub_return(1, &ubufs->refcount);
// r = 0
wait_event(ubufs->wait, !atomic_read(&ubufs->refcount));
// no wait occurs here because condition is already true
kfree(ubufs);
if (unlikely(!r))
wake_up(&ubufs->wait); // use-after-free
This leads to use-after-free on ubufs access. This happens because CPU1
skips waiting for wake_up() when refcount is already zero.
To prevent that use a read-side RCU critical section in vhost_net_ubuf_put(),
as suggested by Hillf Danton. For this lock to take effect, free ubufs with
kfree_rcu().
Since EROFS handles decompression in non-atomic contexts due to
uncontrollable decompression latencies and vmap() usage, it tries
to detect atomic contexts and only kicks off a kworker on demand
in order to reduce unnecessary scheduling overhead.
However, the current approach is insufficient and can lead to
sleeping function calls in invalid contexts, causing kernel
warnings and potential system instability. See the stacktrace [1]
and previous discussion [2].
The current implementation only checks rcu_read_lock_any_held(),
which behaves inconsistently across different kernel configurations:
- When CONFIG_DEBUG_LOCK_ALLOC is enabled: correctly detects
RCU critical sections by checking rcu_lock_map
- When CONFIG_DEBUG_LOCK_ALLOC is disabled: compiles to
"!preemptible()", which only checks preempt_count and misses
RCU critical sections
This patch introduces z_erofs_in_atomic() to provide comprehensive
atomic context detection:
1. Check RCU preemption depth when CONFIG_PREEMPTION is enabled,
as RCU critical sections may not affect preempt_count but still
require atomic handling
2. Always use async processing when CONFIG_PREEMPT_COUNT is disabled,
as preemption state cannot be reliably determined
3. Fall back to standard preemptible() check for remaining cases
The function replaces the previous complex condition check and ensures
that z_erofs always uses (kthread_)work in atomic contexts to minimize
scheduling overhead and prevent sleeping in invalid contexts.
We already have a component driver named "RX-MACRO", which is
lpass-rx-macro.c. The tx macro component driver's name should
be "TX-MACRO" accordingly. Fix it.
Cc: Srinivas Kandagatla <srini@kernel.org> Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patch.msgid.link/20250806140030.691477-1-alexey.klimov@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Besides sending the rename request to the server, the rename process
also involves closing any deferred close, waiting for outstanding I/O
to complete as well as marking all existing open handles as deleted to
prevent them from deferring closes, which increases the race window
for potential concurrent opens on the target file.
Fix this by unhashing the dentry in advance to prevent any concurrent
opens on the target.
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org> Reviewed-by: David Howells <dhowells@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-cifs@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to some logs reported by customers, CIFS client might end up
reporting unlinked files as existing in stat(2) due to concurrent
opens racing with unlink(2).
Besides sending the removal request to the server, the unlink process
could involve closing any deferred close as well as marking all
existing open handles as deleted to prevent them from deferring
closes, which increases the race window for potential concurrent
opens.
Fix this by unhashing the dentry in cifs_unlink() to prevent any
subsequent opens. Any open attempts, while we're still unlinking,
will block on parent's i_rwsem.
Reported-by: Jay Shin <jaeshin@redhat.com> Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org> Reviewed-by: David Howells <dhowells@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-cifs@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SCSI sysfs attributes "supported_mode" and "active_mode" do not
define a store method and thus cannot be modified. Correct the
DEVICE_ATTR() call for these two attributes to not include S_IWUSR to
allow write access as they are read-only.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20250728041700.76660-1-dlemoal@kernel.org Reviewed-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Johannes Thumshin <johannes.thumshirn@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VHOST_[GS]ET_FEATURES_ARRAY ioctl already took 0x83 and it would
result in a build error when the vhost uapi header is used for perf tool
build like below.
In file included from trace/beauty/ioctl.c:93:
tools/perf/trace/beauty/generated/ioctl/vhost_virtio_ioctl_array.c: In function ‘ioctl__scnprintf_vhost_virtio_cmd’:
tools/perf/trace/beauty/generated/ioctl/vhost_virtio_ioctl_array.c:36:18: error: initialized field overwritten [-Werror=override-init]
36 | [0x83] = "SET_FORK_FROM_OWNER",
| ^~~~~~~~~~~~~~~~~~~~~
tools/perf/trace/beauty/generated/ioctl/vhost_virtio_ioctl_array.c:36:18: note: (near initialization for ‘vhost_virtio_ioctl_cmds[131]’)
Fixes: 7d9896e9f6d02d8a ("vhost: Reintroduce kthread API and add mode selection") Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Message-Id: <20250819063958.833770-1-namhyung@kernel.org> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Lei Yang <leiyang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The e_ident is part of the ehdr and so reading it a second time would
mean the read ehdr was displaced by 16-bytes. Switch from stdio to
open/read/lseek syscalls for similarity with the symbol-elf version of
the function and so that later changes can alter then open flags.
Fixes: fef8f648bb47 ("perf symbol: Fix use-after-free in filename__read_build_id") Signed-off-by: Ian Rogers <irogers@google.com> Link: https://lore.kernel.org/r/20250823000024.724394-2-irogers@google.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the context between trace_empty() and trace_find_next_entry_inc()
during ftrace_dump, the ring buffer data was consumed by other readers.
This caused trace_find_next_entry_inc to return NULL, failing to populate
`iter.seq`. At this point, due to the prior trace_iterator_reset, both
`iter.seq.len` and `iter.seq.size` were set to 0. Since they are equal,
the WARN_ON_ONCE condition is triggered.
Move the trace_printk_seq() into the if block that checks to make sure the
return value of trace_find_next_entry_inc() is non-NULL in
ftrace_dump_one(), ensuring the 'iter.seq' is properly populated before
subsequent operations.
If the of_changeset_add_property() function call fails, then this code
frees "new_pp" and then dereference it on the next line. Return the
error code directly instead.
Fixes: c81f6ce16785 ("of: dynamic: Fix memleak when of_pci_add_properties() failed") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/aKgljjhnpa4lVpdx@stanley.mountain Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bindig requires a node name matching ‘^ethernet@[0-9a-f]+$’. This patch
changes the clock name from “etop” to “ethernet”.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): $nodename:0: 'etop@e180000' does not match '^ethernet@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: dac0bad93741 ("dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The upstream dts lacks the lantiq,{rx/tx}-burst-length property. Other
issues were also fixed:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'interrupt-names' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,tx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: etop@e180000 (lantiq,etop-xway): 'lantiq,rx-burst-length' is a required property
from schema $id: http://devicetree.org/schemas/net/lantiq,etop-xway.yaml#
Fixes: 14d4e308e0aa ("net: lantiq: configure the burst length in ethernet drivers") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building on ARCH=um (which does not set HAS_IOMEM), kconfig
reports an unmet dependency caused by PINCTRL_STMFX. It selects
MFD_STMFX, which depends on HAS_IOMEM. To stop this warning,
PINCTRL_STMFX should also depend on HAS_IOMEM.
kconfig warning:
WARNING: unmet direct dependencies detected for MFD_STMFX
Depends on [n]: HAS_IOMEM [=n] && I2C [=y] && OF [=y]
Selected by [y]:
- PINCTRL_STMFX [=y] && PINCTRL [=y] && I2C [=y] && OF_GPIO [=y]
When of_pci_add_properties() failed, of_changeset_destroy() is called to
free the changeset. And of_changeset_destroy() puts device tree node in
each entry but does not free property in the entry. This leads to memory
leak in the failure case.
In of_changeset_add_prop_helper(), add the property to the device tree node
deadprops list. Thus, the property will also be freed along with device
tree node.
Fixes: b544fc2b8606 ("of: dynamic: Add interfaces for creating device node dynamically") Reported-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Closes: https://lore.kernel.org/all/aJms+YT8TnpzpCY8@lpieralisi/ Tested-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Lizhi Hou <lizhi.hou@amd.com> Link: https://lore.kernel.org/r/20250818152221.3685724-1-lizhi.hou@amd.com Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When writing to the function_profile_enabled interface, the notifier was
not unregistered after start_graph_tracing failed, causing a warning the
next time function_profile_enabled was written.
Fixed by adding unregister_pm_notifier in the exception path.
Link: https://lore.kernel.org/20250818073332.3890629-1-yeweihua4@huawei.com Fixes: 4a2b8dda3f870 ("tracing/function-graph-tracer: fix a regression while suspend to disk") Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Ye Weihua <yeweihua4@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The tool pkg-config used to check libtraceevent and libtracefs, if not
installed, it will report the libs not found, even though they have
already been installed.
Before:
libtraceevent is missing. Please install libtraceevent-dev/libtraceevent-devel
libtracefs is missing. Please install libtracefs-dev/libtracefs-devel
After:
Makefile.config:10: *** Error: pkg-config needed by libtraceevent/libtracefs is missing
on this system, please install it.
Link: https://lore.kernel.org/20250808040527.2036023-2-chen.dylane@linux.dev Fixes: 01474dc706ca ("tools/rtla: Use tools/build makefiles to build rtla") Signed-off-by: Tao Chen <chen.dylane@linux.dev> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The tool pkg-config used to check libtraceevent and libtracefs, if not
installed, it will report the libs not found, even though they have
already been installed.
Before:
libtraceevent is missing. Please install libtraceevent-dev/libtraceevent-devel
libtracefs is missing. Please install libtracefs-dev/libtracefs-devel
After:
Makefile.config:10: *** Error: pkg-config needed by libtraceevent/libtracefs is missing
on this system, please install it.
Link: https://lore.kernel.org/20250808040527.2036023-1-chen.dylane@linux.dev Fixes: 9d56c88e5225 ("tools/tracing: Use tools/build makefiles on latency-collector") Signed-off-by: Tao Chen <chen.dylane@linux.dev> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
First of all, tell it how many slots do we want, not which slot
is wanted. It makes one caller (dup_fd()) more straightforward
and doesn't harm another (expand_fdtable()).
Furthermore, make it return ERR_PTR() on failure rather than
returning NULL. Simplifies the callers.
Simplify the size calculation, while we are at it - note that we
always have slots_wanted greater than BITS_PER_LONG. What the
rules boil down to is
* use the smallest power of two large enough to give us
that many slots
* on 32bit skip 64 and 128 - the minimal capacity we want
there is 256 slots (i.e. 1Kb fd array).
* on 64bit don't skip anything, the minimal capacity is
128 - and we'll never be asked for 64 or less. 128 slots means
1Kb fd array, again.
* on 128bit, if that ever happens, don't skip anything -
we'll never be asked for 128 or less, so the fd array allocation
will be at least 2Kb.
Reviewed-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kernel lockdown is active, debugfs_locked_down() blocks access to
hypfs files that register ioctl callbacks, even if the ioctl interface
is not required for a function. This unnecessarily breaks userspace
tools that only rely on read operations.
Resolve this by registering a minimal set of file operations during
lockdown, avoiding ioctl registration and preserving access for affected
tooling.
Note that this change restores hypfs functionality when lockdown is
active from early boot (e.g. via lockdown=integrity kernel parameter),
but does not apply to scenarios where lockdown is enabled dynamically
while Linux is running.
Tested-by: Mete Durlu <meted@linux.ibm.com> Reviewed-by: Vasily Gorbik <gor@linux.ibm.com> Fixes: 5496197f9b08 ("debugfs: Restrict debugfs when the kernel is locked down") Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, hypfs registers ioctl callbacks for all debugfs files,
despite only one file requiring them. This leads to unintended exposure
of unused interfaces to user space and can trigger side effects such as
restricted access when kernel lockdown is enabled.
Restrict ioctl registration to only those files that implement ioctl
functionality to avoid interface clutter and unnecessary access
restrictions.
Tested-by: Mete Durlu <meted@linux.ibm.com> Reviewed-by: Vasily Gorbik <gor@linux.ibm.com> Fixes: 5496197f9b08 ("debugfs: Restrict debugfs when the kernel is locked down") Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The entry of the validators table for UAC3 feature unit is defined
with a wrong sub-type UAC_FEATURE (= 0x06) while it should have been
UAC3_FEATURE (= 0x07). This patch corrects the entry value.
When port buffer headroom changes, port_update_shared_buffer()
recalculates the shared buffer size and splits it in a 3:1 ratio
(lossy:lossless) - Currently, the calculation is:
lossless = shared / 4;
lossy = (shared / 4) * 3;
Meaning, the calculation dropped the remainder of shared % 4 due to
integer division, unintentionally reducing the total shared buffer
by up to three cells on each update. Over time, this could shrink
the buffer below usable size.
Fix it by changing the calculation to:
lossless = shared / 4;
lossy = shared - lossless;
This retains all buffer cells while still approximating the
intended 3:1 split, preventing capacity loss over time.
While at it, perform headroom calculations in units of cells rather than
in bytes for more accurate calculations avoiding extra divisions.
The SW currently saves local buffer ownership when setting
the buffer.
This means that the SW assumes it has ownership of the buffer
after the command is set.
If setting the buffer fails and we remain in FW ownership,
the local buffer ownership state incorrectly remains as SW-owned.
This leads to incorrect behavior in subsequent PFC commands,
causing failures.
Instead of saving local buffer ownership in SW,
query the FW for buffer ownership when setting the buffer.
This ensures that the buffer ownership state is accurately
reflected, avoiding the issues caused by incorrect ownership
states.
Fixes: ecdf2dadee8e ("net/mlx5e: Receive buffer support for DCBX") Signed-off-by: Alexei Lazar <alazar@nvidia.com> Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Link: https://patch.msgid.link/20250820133209.389065-8-mbloch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The port header is a general file under include, yet it
contains declarations for functions that are either not
exported or exported but not used outside the mlx5_core
driver.
To enhance code organization, we move these declarations
to mlx5_core.h, where they are more appropriately scoped.
This refactor removes unnecessary exported symbols and
prevents unexported functions from being inadvertently
referenced outside of the mlx5_core driver.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com> Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20250304160620.417580-2-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 451d2849ea66 ("net/mlx5e: Query FW for buffer ownership") Signed-off-by: Sasha Levin <sashal@kernel.org>
Adjust the vport number by the base ECVF vport number so the port
attributes start at 0. Previously the port attributes would start 1
after the maximum number of host VFs.
Fixes: dc13180824b7 ("net/mlx5: Enable devlink port for embedded cpu VF vports") Signed-off-by: Daniel Jurgens <danielj@nvidia.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Link: https://patch.msgid.link/20250820133209.389065-2-mbloch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Octeontx2/CN10K silicon supports generating a 256-bit key per packet.
The specific fields to be extracted from a packet for key generation
are configurable via a Key Extraction (MKEX) Profile.
The AF driver scans the configured extraction profile to ensure that
fields from upper layers do not overwrite fields from lower layers in
the key.
Example Packet Field Layout:
LA: DMAC + SMAC
LB: VLAN
LC: IPv4/IPv6
LD: TCP/UDP
Valid MKEX Profile Configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[30-31]
Invalid MKEX profile configuration:
LA -> DMAC -> key_offset[0-5]
LC -> SIP -> key_offset[20-23]
LD -> SPORT -> key_offset[2-3] // Overlaps with DMAC field
In another scenario, if the MKEX profile is configured to extract
the SPI field from both AH and ESP headers at the same key offset,
the driver rejecting this configuration. In a regular traffic,
ipsec packet will be having either AH(LD) or ESP (LE). This patch
relaxes the check for the same.
When `lacp_active` is set to `off`, the bond operates in passive mode, meaning
it only "speaks when spoken to." However, the current kernel implementation
only sends an LACPDU in response when the partner's state changes.
As a result, once LACP negotiation succeeds, the actor stops sending LACPDUs
until the partner times out and sends an "expired" LACPDU. This causes
continuous LACP state flapping.
According to IEEE 802.1AX-2014, 6.4.13 Periodic Transmission machine. The
values of Partner_Oper_Port_State.LACP_Activity and
Actor_Oper_Port_State.LACP_Activity determine whether periodic transmissions
take place. If either or both parameters are set to Active LACP, then periodic
transmissions occur; if both are set to Passive LACP, then periodic
transmissions do not occur.
To comply with this, we remove the `!bond->params.lacp_active` check in
`ad_periodic_machine()`. Instead, we initialize the actor's port's
`LACP_STATE_LACP_ACTIVITY` state based on `lacp_active` setting.
Additionally, we avoid setting the partner's state to
`LACP_STATE_LACP_ACTIVITY` in the EXPIRED state, since we should not assume
the partner is active by default.
This ensures that in passive mode, the bond starts sending periodic LACPDUs
after receiving one from the partner, and avoids flapping due to inactivity.
Fixes: 3a755cd8b7c6 ("bonding: add new option lacp_active") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://patch.msgid.link/20250815062000.22220-3-liuhangbin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The port's actor_oper_port_state activity flag should be updated immediately
after changing the lacp_active option to reflect the current mode correctly.
Fixes: 3a755cd8b7c6 ("bonding: add new option lacp_active") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://patch.msgid.link/20250815062000.22220-2-liuhangbin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the snd_utimer_create() function, if the kasprintf() function return
NULL, snd_utimer_put_id() will be called, finally use ida_free()
to free the unallocated id 0.
The following setup can trigger a WARNING in htb_activate due to
the condition: !cl->leaf.q->q.qlen
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: htb default 1
tc class add dev lo parent 1: classid 1:1 \
htb rate 64bit
tc qdisc add dev lo parent 1:1 handle f: \
cake memlimit 1b
ping -I lo -f -c1 -s64 -W0.001 127.0.0.1
This is because the low memlimit leads to a low buffer_limit, which
causes packet dropping. However, cake_enqueue still returns
NET_XMIT_SUCCESS, causing htb_enqueue to call htb_activate with an
empty child qdisc. We should return NET_XMIT_CN when packets are
dropped from the same tin and flow.
I do not believe return value of NET_XMIT_CN is necessary for packet
drops in the case of ack filtering, as that is meant to optimize
performance, not to signal congestion.
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc") Signed-off-by: William Liu <will@willsroot.io> Reviewed-by: Savino Dicanosa <savy@syst3mfailure.io> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20250819033601.579821-1-will@willsroot.io Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ksz9477_hsr_join() is called once to setup the HSR port membership, but
the port can be enabled later, or disabled and enabled back and the port
membership is not set correctly inside ksz_update_port_member(). The
added code always use the correct HSR port membership for HSR port that
is enabled.
Without L1.2 disabled, the speed would be no more than ~200 mbit/s.
With L1.2 disabled, the speed would reach 1 gbit/s.
Note: it's required that the latency between your host and the remote
be around 3-5 ms, the test inside LAN (<1 ms latency) won't trigger the
issue.
Resolve the budget negative overflow which leads to returning true in
ixgbe_xmit_zc even when the budget of descs are thoroughly consumed.
Before this patch, when the budget is decreased to zero and finishes
sending the last allowed desc in ixgbe_xmit_zc, it will always turn back
and enter into the while() statement to see if it should keep processing
packets, but in the meantime it unexpectedly decreases the value again to
'unsigned int (0--)', namely, UINT_MAX. Finally, the ixgbe_xmit_zc returns
true, showing 'we complete cleaning the budget'. That also means
'clean_complete = true' in ixgbe_poll.
The true theory behind this is if that budget number of descs are consumed,
it implies that we might have more descs to be done. So we should return
false in ixgbe_xmit_zc to tell napi poll to find another chance to start
polling to handle the rest of descs. On the contrary, returning true here
means job done and we know we finish all the possible descs this time and
we don't intend to start a new napi poll.
It is apparently against our expectations. Please also see how
ixgbe_clean_tx_irq() handles the problem: it uses do..while() statement
to make sure the budget can be decreased to zero at most and the negative
overflow never happens.
The patch adds 'likely' because we rarely would not hit the loop condition
since the standard budget is 256.
Fixes: 8221c5eba8c1 ("ixgbe: add AF_XDP zero-copy Tx support") Signed-off-by: Jason Xing <kernelxing@tencent.com> Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Priya Singh <priyax.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250819222000.3504873-4-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the identity mapping is pinned to address zero the lowcore is always
also mapped to address zero, this happens regardless of the relocate_lowcore
command line option. If the option is specified the lowcore is mapped
twice, instead of only once.
This means that NULL pointer accesses will succeed instead of causing an
exception (low address protection still applies, but covers only parts).
To fix this never map the first two pages of physical memory with the
identity mapping.
Fixes: 32db401965f1 ("s390/mm: Pin identity mapping base to zero") Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When enabling CONFIG_KASAN, CONFIG_PREEMPT_VOLUNTARY_BUILD and
CONFIG_PREEMPT_VOLUNTARY at the same time, there will be soft deadlock,
the relevant logs are as follows:
After analysis, this is because the slow speed of loading the amdgpu
module leads to the long time occupation of the cpu and then the soft
deadlock.
When loading a module, module_frob_arch_sections() tries to figure out
the number of PLTs/GOTs that will be needed to handle all the RELAs. It
will call the count_max_entries() to find in an out-of-order date which
counting algorithm has O(n^2) complexity.
To make it faster, we sort the relocation list by info and addend. That
way, to check for a duplicate relocation, it just needs to compare with
the previous entry. This reduces the complexity of the algorithm to O(n
log n), as done in commit d4e0340919fb ("arm64/module: Optimize module
load time by optimizing PLT counting"). This gives sinificant reduction
in module load time for modules with large number of relocations.
After applying this patch, the soft deadlock problem has been solved,
and the kernel starts normally without "Call Trace".
Using the default configuration to test some modules, the results are as
follows:
Fix missing configuration for LAN865x silicon revisions B0 and B1 as per
Microchip Application Note AN1760 (Rev F, June 2024).
The Timer Increment register was not being set, which is required for
accurate timestamping. As per the application note, configure the MAC to
set timestamping at the end of the Start of Frame Delimiter (SFD), and
set the Timer Increment register to 40 ns (corresponding to a 25 MHz
internal clock).
This fixes an issue where the transmit queue is started implicitly only
the very first time the device is registered. When the device is taken
down and brought back up again (using `ip` or `ifconfig`), the transmit
queue is not restarted, causing packet transmission to hang.
Adding an explicit call to netif_start_queue() in lan865x_net_open()
ensures the transmit queue is properly started every time the device
is reopened.
Fixes: 5cd2340cb6a3 ("microchip: lan865x: add driver support for Microchip's LAN865X MAC-PHY") Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com> Link: https://patch.msgid.link/20250818060514.52795-2-parthiban.veerasooran@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The direct cause of this issue is that after smc_listen_out_connected(),
newclcsock->sk may be NULL since it will releases the smcsk. Therefore,
if the application closes the socket immediately after accept,
newclcsock->sk can be NULL. A possible execution order could be as
follows:
Since smc_listen_out_connected() will not fail, simply swapping the order
of the code can easily fix this issue.
Fixes: 3b2dec2603d5 ("net/smc: restructure client and server code in af_smc") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Link: https://patch.msgid.link/20250818054618.41615-1-alibuda@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A crash can occur if an ethtool operation is invoked
after shutdown() is called.
shutdown() is invoked during system shutdown to stop DMA operations
without performing expensive deallocations. It is discouraged to
unregister the netdev in this path, so the device may still be visible
to userspace and kernel helpers.
In gve, shutdown() tears down most internal data structures. If an
ethtool operation is dispatched after shutdown(), it will dereference
freed or NULL pointers, leading to a kernel panic. While graceful
shutdown normally quiesces userspace before invoking the reboot
syscall, forced shutdowns (as observed on GCP VMs) can still trigger
this path.
Fix by calling netif_device_detach() in shutdown().
This marks the device as detached so the ethtool ioctl handler
will skip dispatching operations to the driver.
Fixes: 974365e51861 ("gve: Implement suspend/resume/shutdown") Signed-off-by: Jordan Rhee <jordanrhee@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Link: https://patch.msgid.link/20250818211245.1156919-1-jeroendb@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported shift-out-of-bounds exception on MDIO bus initialization.
The PHY address should be masked to 5 bits (0-31). Without this
mask, invalid PHY addresses could be used, potentially causing issues
with MDIO bus operations.
Fix this by masking the PHY address with 0x1f (31 decimal) to ensure
it stays within the valid range.
There was a problem when we received frames and the frames were
timestamped. The driver is configured to store the nanosecond part of
the timestmap in the ptp reserved bits and it would take the second part
by reading the LTC. The problem is that when reading the LTC we are in
atomic context and to read the second part will go over mdio bus which
might sleep, so we get an error.
The fix consists in actually put all the frames in a queue and start the
aux work and in that work to read the LTC and then calculate the full
received time.
Fix smb3_init_transform_rq() to initialise buffer to NULL before calling
netfs_alloc_folioq_buffer() as netfs assumes it can append to the buffer it
is given. Setting it to NULL means it should start a fresh buffer, but the
value is currently undefined.
Fixes: a2906d3316fc ("cifs: Switch crypto buffer to use a folio_queue rather than an xarray") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.org>
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To enable HSR / Switch offload, certain configurations are needed.
Currently they are done inside icssg_change_mode(). This function only
gets called if we move from one mode to another without bringing the
links up / down.
Once in HSR / Switch mode, if we bring the links down and bring it back
up again. The callback sequence is,
- emac_ndo_stop()
Firmwares are stopped
- emac_ndo_open()
Firmwares are loaded
In this path icssg_change_mode() doesn't get called and as a result the
configurations needed for HSR / Switch is not done.
To fix this, put all these configurations in a separate function
icssg_enable_fw_offload() and call this from both icssg_change_mode()
and emac_ndo_open()
Fixes: 56375086d093 ("net: ti: icssg-prueth: Enable HSR Tx duplication, Tx Tag and Rx Tag offload") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Link: https://patch.msgid.link/20250814105106.1491871-1-danishanwar@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. The ppp->channels list can change between list_empty() and
list_first_entry(), as ppp_lock() is not held. If the only channel
is deleted in ppp_disconnect_channel(), list_first_entry() may
access an empty head or a freed entry, and trigger a panic.
2. pch->chan can be NULL. When ppp_unregister_channel() is called,
pch->chan is set to NULL before pch is removed from ppp->channels.
Fix these by using a lockless RCU approach:
- Use list_first_or_null_rcu() to safely test and access the first list
entry.
- Convert list modifications on ppp->channels to their RCU variants and
add synchronize_net() after removal.
- Check for a NULL pch->chan before dereferencing it.
Fixes: f6efc675c9dd ("net: ppp: resolve forwarding path for bridge pppoe devices") Signed-off-by: Qingfang Deng <dqfext@gmail.com> Link: https://patch.msgid.link/20250814012559.3705-2-dqfext@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The seg6_genl_sethmac() directly uses the algorithm ID provided by the
userspace without verifying whether it is an HMAC algorithm supported
by the system.
If an unsupported HMAC algorithm ID is configured, packets using SRv6 HMAC
will be dropped during encapsulation or decapsulation.
Fixes: 4f4853dc1c9c ("ipv6: sr: implement API to control SR HMAC structure") Signed-off-by: Minhong He <heminhong@kylinos.cn> Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com> Link: https://patch.msgid.link/20250815063845.85426-1-heminhong@kylinos.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When performing Generic Segmentation Offload (GSO) on an IPv6 packet that
contains extension headers, the kernel incorrectly requests checksum offload
if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has
a strict contract: it supports checksum offload only for plain TCP or UDP
over IPv6 and explicitly does not support packets with extension headers.
The current GSO logic violates this contract by failing to disable the feature
for packets with extension headers, such as those used in GREoIPv6 tunnels.
This violation results in the device being asked to perform an operation
it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse
of network throughput. While device TSO/USO is correctly bypassed in favor
of software GSO for these packets, the GSO stack must be explicitly told not
to request checksum offload.
Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4
in gso_features_check if the IPv6 header contains extension headers to compute
checksum in software.
The exception is a BIG TCP extension, which, as stated in commit 68e068cabd2c6c53 ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"):
"The feature is only enabled on devices that support BIG TCP TSO.
The header is only present for PF_PACKET taps like tcpdump,
and not transmitted by physical devices."
Fixes: 04c20a9356f283da ("net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension") Reported-by: Tianhao Zhao <tizhao@redhat.com> Suggested-by: Michal Schmidt <mschmidt@redhat.com> Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by: Jakub Ramaseuski <jramaseu@redhat.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20250814105119.1525687-1-jramaseu@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When getting the number of connectors, the VBIOS reports
the number of valid indices, but it doesn't say which indices
are valid, and not every valid index has an actual connector.
If we don't find a connector on an index, that is not an error.
Considering these are not actual errors, don't litter the logs.
Fixes: 60df5628144b ("drm/amd/display: handle invalid connector indices") Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 249d4bc5f1935f04bb45b3b63c0f8922565124f7) Signed-off-by: Sasha Levin <sashal@kernel.org>
The function mod_hdcp_hdcp1_create_session() calls the function
get_first_active_display(), but does not check its return value.
The return value is a null pointer if the display list is empty.
This will lead to a null pointer dereference.
Add a null pointer check for get_first_active_display() and return
MOD_HDCP_STATUS_DISPLAY_NOT_FOUND if the function return null.
This is similar to the commit c3e9826a2202
("drm/amd/display: Add null pointer check for get_first_active_display()").
Fixes: 2deade5ede56 ("drm/amd/display: Remove hdcp display state with mst fix") Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5e43eb3cd731649c4f8b9134f857be62a416c893) Signed-off-by: Sasha Levin <sashal@kernel.org>
When hibmc loaded failed, the driver use hibmc_unload to free the
resource, but the mutexes in mode.config are not init, which will
access an NULL pointer. Just change goto statement to return, because
hibnc_hw_init() doesn't need to free anything.
Fixes: b3df5e65cc03 ("drm/hibmc: Drop drm_vblank_cleanup") Signed-off-by: Baihan Li <libaihan@huawei.com> Signed-off-by: Yongbang Shi <shiyongbang@huawei.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250813094238.3722345-5-shiyongbang@huawei.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit fde578c86281 ("rust: alloc: replace aligned_size() with
Kmalloc::aligned_layout()") provides a public `aligned_layout` function
in `Kamlloc`, but not in `Cmalloc`, and thus uses of it will trigger an
error in `rusttest`.
Such a user appeared in the following commit 22ab0641b939 ("rust: drm:
ensure kmalloc() compatible Layout"):
error[E0599]: no function or associated item named `aligned_layout` found for struct `alloc::allocator_test::Cmalloc` in the current scope
--> rust/kernel/drm/device.rs:100:31
|
100 | let layout = Kmalloc::aligned_layout(Layout::new::<Self>());
| ^^^^^^^^^^^^^^ function or associated item not found in `Cmalloc`
|
::: rust/kernel/alloc/allocator_test.rs:19:1
|
19 | pub struct Cmalloc;
| ------------------ function or associated item `aligned_layout` not found for this struct
By default, the device does not forward IPv4 packets with a link-local
source IP (i.e., 169.254.0.0/16). This behavior does not align with the
kernel which does forward them.
Fix by instructing the device to forward such packets instead of
dropping them.
Fixes: ca360db4b825 ("mlxsw: spectrum: Disable DIP_LINK_LOCAL check in hardware pipeline") Reported-by: Zoey Mertes <zoey@cloudflare.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Link: https://patch.msgid.link/6721e6b2c96feb80269e72ce8d0b426e2f32d99c.1755174341.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit e07a06b4eb41 ("Bluetooth: Convert SCO configure_datapath to
hci_sync") missed to update the *return* statement under the *case* of
BT_CODEC_TRANSPARENT in hci_enhanced_setup_sync(), which led to returning
success (0) instead of the negative error code (-EINVAL). However, the
result of hci_enhanced_setup_sync() seems to be ignored anyway, since NULL
gets passed to hci_cmd_sync_queue() as the last argument in that case and
the only function interested in that result is specified by that argument.
Fixes: e07a06b4eb41 ("Bluetooth: Convert SCO configure_datapath to hci_sync") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BN == 0x00 in CIS Established means no isochronous data for the
corresponding direction (Core v6.1 pp. 2394). In this case SDU MTU
should be 0.
However, the specification does not say the Max_PDU_C_To_P or P_To_C are
then zero. Intel AX210 in Framed CIS mode sets nonzero Max_PDU for
direction with zero BN. This causes failure later when we try to LE
Setup ISO Data Path for disabled direction, which is disallowed (Core
v6.1 pp. 2750).
Fix by setting SDU MTU to 0 if BN == 0.
Fixes: 2be22f1941d5f ("Bluetooth: hci_event: Fix parsing of CIS Established Event") Signed-off-by: Pauli Virtanen <pav@iki.fi> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: e2d471b7806b ("Bluetooth: ISO: Fix not using SID from adv report") Signed-off-by: Yang Li <yang.li@amlogic.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During the shutdown process, an interrupt occurs that
prematurely terminates the wait for the expected event.
This change replaces TASK_INTERRUPTIBLE with
TASK_UNINTERRUPTIBLE in the wait_on_bit_timeout call to ensure
the shutdown process completes as intended without being
interrupted by signals.
Fixes: d019930b0049 ("Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.c") Signed-off-by: Jiande Lu <jiande.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Passive scanning is used to program the address of the peer to be
synchronized, so once HCI_EV_LE_PA_SYNC_ESTABLISHED is received it
needs to be updated after clearing HCI_PA_SYNC then call
hci_update_passive_scan_sync to return it to its original state.
Fixes: 6d0417e4e1cf ("Bluetooth: hci_conn: Fix not setting conn_timeout for Broadcast Receiver") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the kernel command line is considered trusted in most environments,
avoid writing 1 byte past the end of "acpiid" if the "str" argument is
maximum length.
Reported-by: Simcha Kosman <simcha.kosman@cyberark.com> Closes: https://lore.kernel.org/all/AS8P193MB2271C4B24BCEDA31830F37AE84A52@AS8P193MB2271.EURP193.PROD.OUTLOOK.COM Fixes: b6b26d86c61c ("iommu/amd: Add a length limitation for the ivrs_acpihid command-line parameter") Signed-off-by: Kees Cook <kees@kernel.org> Reviewed-by: Ankit Soni <Ankit.Soni@amd.com> Link: https://lore.kernel.org/r/20250804154023.work.970-kees@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The qla4xxx_get_ep_fwdb() function is supposed to return NULL on error,
but qla4xxx_ep_connect() returns error pointers. Propagating the error
pointers will lead to an Oops in the caller, so change the error pointers
to NULL.
Fixes: 13483730a13b ("[SCSI] qla4xxx: fix flash/ddb support") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/aJwnVKS9tHsw1tEu@stanley.mountain Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The CRC error bit is located at bit 17 in the Rx descriptor, but the
driver was incorrectly using bit 16. Fix it.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module") Signed-off-by: Justin Lai <justinlai0215@realtek.com> Link: https://patch.msgid.link/20250813071631.7566-1-justinlai0215@realtek.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When set multicast_query_interval to a large value, the local variable
'time' in br_multicast_send_query() may overflow. If the time is smaller
than jiffies, the timer will expire immediately, and then call mod_timer()
again, which creates a loop and may trigger the following soft lockup
issue.
This issue can be reproduced with:
ip link add br0 type bridge
echo 1 > /sys/class/net/br0/bridge/multicast_querier
echo 0xffffffffffffffff >
/sys/class/net/br0/bridge/multicast_query_interval
ip link set dev br0 up
The multicast_startup_query_interval can also cause this issue. Similar to
the commit 99b40610956a ("net: bridge: mcast: add and enforce query
interval minimum"), add check for the query interval maximum to fix this
issue.
Submit multiple descriptors in axienet_rx_cb() to fill Rx skb ring. This
ensures the ring "catches up" on previously missed allocations.
Increment Rx skb ring head pointer after BD is successfully allocated.
Previously, head pointer was incremented before verifying if descriptor is
successfully allocated and has valid entries, which could lead to ring
state inconsistency if descriptor setup failed.
These changes improve reliability by maintaining adequate descriptor
availability and ensuring proper ring buffer state management.
DIP algorithm is also supported on devices newer than hip09, so free
dip entries too.
Fixes: f91696f2f053 ("RDMA/hns: Support congestion control type selection according to the FW") Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://patch.msgid.link/20250812122602.3524602-1-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The GID context reuse logic requires the context memory to be
not freed if and when DEL_GID firmware command fails. But, if
there's no subsequent ADD_GID to reuse it, the context memory
must be freed when the driver is unloaded. Otherwise it leads
to a memory leak.
When using DIP algorithm, all QPs establishing connections with
the same destination IP share the same SCC, which is indexed by
dip_idx, but dip_idx isn't necessarily equal to qpn. Therefore,
dip_idx should be used to query SCC context instead of qpn.
Fixes: 124a9fbe43aa ("RDMA/hns: Append SCC context to the raw dump of QPC") Signed-off-by: wenglianfa <wenglianfa@huawei.com> Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://patch.msgid.link/20250726075345.846957-1-huangjunxian6@hisilicon.com Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
aligned_size() dates back to when Rust did support kmalloc() only, but
is now used in ReallocFunc::call() and hence for all allocators.
However, the additional padding applied by aligned_size() is only
required by the kmalloc() allocator backend.
Hence, replace aligned_size() with Kmalloc::aligned_layout() and use it
for the affected allocators, i.e. kmalloc() and kvmalloc(), only.
While at it, make Kmalloc::aligned_layout() public, such that Rust
abstractions, which have to call subsystem specific kmalloc() based
allocation primitives directly, can make use of it.
The current iosys_map_clear() implementation reads the potentially
uninitialized 'is_iomem' boolean field to decide which union member
to clear. This causes undefined behavior when called on uninitialized
structures, as 'is_iomem' may contain garbage values like 0xFF.
UBSAN detects this as:
UBSAN: invalid-load in include/linux/iosys-map.h:267
load of value 255 is not a valid value for type '_Bool'
Fix by unconditionally clearing the entire structure with memset(),
eliminating the need to read uninitialized data and ensuring all
fields are set to known good values.
Fix failures on big-endian architectures on tests cases
single_pixel_source_buffer, single_pixel_clip_rectangle,
well_known_colors and destination_pitch.
Fixes: 15bda1f8de5d ("drm/tests: Add calls to drm_fb_blit() on supported format conversion tests") Signed-off-by: José Expósito <jose.exposito89@gmail.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://lore.kernel.org/r/20250630090054.353246-2-jose.exposito89@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Export additional helpers from the format-helper library and open-code
drm_fb_blit() in tests. Prepares for the removal of drm_fb_blit(). Only
sysfb drivers use drm_fb_blit(). The function will soon be removed from
format helpers and be refactored within sysfb helpers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: José Expósito <jose.exposito89@gmail.com> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://lore.kernel.org/r/20250616083846.221396-2-tzimmermann@suse.de
Stable-dep-of: 05663d88fd0b ("drm/tests: Fix drm_test_fb_xrgb8888_to_xrgb2101010() on big-endian") Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
