bnxt_en: Fix coredump logic to free allocated buffer
When handling HWRM_DBG_COREDUMP_LIST FW command in
bnxt_hwrm_dbg_dma_data(), the allocated buffer info->dest_buf is
not freed in the error path. In the normal path, info->dest_buf
is assigned to coredump->data and it will eventually be freed after
the coredump is collected.
Free info->dest_buf immediately inside bnxt_hwrm_dbg_dma_data() in
the error path.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length") Reported-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Shruti Parab <shruti.parab@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: delay pci_alloc_irq_vectors() in the AER path
This patch is similar to the last patch to delay the
pci_alloc_irq_vectors() call in the AER path until after calling
bnxt_reserve_rings(). bnxt_reserve_rings() needs to properly map
the MSIX table first before we call pci_alloc_irq_vectors() which
may immediately write to the MSIX table in some architectures.
Move the bnxt_init_int_mode() call from bnxt_io_slot_reset() to
bnxt_io_resume() after calling bnxt_reserve_rings().
With this change, the AER path may call bnxt_open() ->
bnxt_hwrm_if_change() with bp->irq_tbl set to NULL. bp->irq_tbl is
cleared when we call bnxt_clear_int_mode() in bnxt_io_slot_reset().
So we cannot use !bp->irq_tbl to detect aborted FW reset. Add a
new BNXT_FW_RESET_STATE_ABORT to detect aborted FW reset in
bnxt_hwrm_if_change().
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: call pci_alloc_irq_vectors() after bnxt_reserve_rings()
On some architectures (e.g. ARM), calling pci_alloc_irq_vectors()
will immediately cause the MSIX table to be written. This will not
work if we haven't called bnxt_reserve_rings() to properly map
the MSIX table to the MSIX vectors reserved by FW.
Fix the FW error recovery path to delay the bnxt_init_int_mode() ->
pci_alloc_irq_vectors() call by removing it from bnxt_hwrm_if_change().
bnxt_request_irq() later in the code path will call it and by then the
MSIX table is properly mapped.
Fixes: 4343838ca5eb ("bnxt_en: Replace deprecated PCI MSIX APIs") Suggested-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: Add missing skb_mark_for_recycle() in bnxt_rx_vlan()
If bnxt_rx_vlan() fails because the VLAN protocol ID is invalid,
the SKB is freed but we're missing the call to recycle it. This
may cause the warning:
"page_pool_release_retry() stalled pool shutdown"
Add the missing skb_mark_for_recycle() in bnxt_rx_vlan().
Fixes: 86b05508f775 ("bnxt_en: Use the unified RX page pool buffers for XDP and non-XDP") Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Mon, 28 Apr 2025 22:58:57 +0000 (15:58 -0700)]
bnxt_en: Fix ethtool selftest output in one of the failure cases
When RDMA driver is loaded, running offline self test is not
supported and driver returns failure early. But it is not clearing
the input buffer and hence the application prints some junk
characters for individual test results.
Fix it by clearing the buffer before returning.
Fixes: 895621f1c816 ("bnxt_en: Don't support offline self test when RoCE driver is loaded") Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: Fix error handling path in bnxt_init_chip()
WARN_ON() is triggered in __flush_work() if bnxt_init_chip() fails
because we call cancel_work_sync() on dim work that has not been
initialized.
WARNING: CPU: 37 PID: 5223 at kernel/workqueue.c:4201 __flush_work.isra.0+0x212/0x230
The driver relies on the BNXT_STATE_NAPI_DISABLED bit to check if dim
work has already been cancelled. But in the bnxt_open() path,
BNXT_STATE_NAPI_DISABLED is not set and this causes the error
path to think that it needs to cancel the uninitalized dim work.
Fix it by setting BNXT_STATE_NAPI_DISABLED during initialization.
The bit will be cleared when we enable NAPI and initialize dim work.
Fixes: 40452969a506 ("bnxt_en: Fix DIM shutdown") Suggested-by: Somnath Kotur <somnath.kotur@broadcom.com> Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Shravya KN <shravya.k-n@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Sat, 26 Apr 2025 15:32:09 +0000 (17:32 +0200)]
net: ipv6: fix UDPv6 GSO segmentation with NAT
If any address or port is changed, update it in all packets and recalculate
checksum.
Fixes: 9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.") Signed-off-by: Felix Fietkau <nbd@nbd.name> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20250426153210.14044-1-nbd@nbd.name Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Fix Felix DSA taprio gates after clock jump
Richie Pearn presented a reproducible situation where traffic would get
blocked on the NXP LS1028A switch if a certain taprio schedule was
applied, and stepping the PTP clock would take place. The latter event
is an expected initial occurrence, but also at runtime, for example when
transitioning from one grandmaster to another.
The issue is completely described in patch 1/4, which also contains
the fix, but it has left me with some doubts regarding the need for
vsc9959_tas_clock_adjust() in general.
In order to prove to myself that vsc9959_tas_clock_adjust() is needed in
general, I have written a selftest for the tc-taprio data path in patch
4/4. On the LS1028A, we can clearly see the following failures without
that function:
INFO: Forcing a backward clock jump
TEST: ping [FAIL]
INFO: Setting up taprio after PTP
TEST: In band with gate [FAIL]
Reception of 100 packets failed
TEST: Out of band with gate [FAIL]
Reception of 100 packets failed
As for testing my fix from patch 1/4, that was quite a bit more complex
to do automatically. In fact, I couldn't find any other schedule that
would fail to be updated by vsc9959_tas_clock_adjust() as cleanly as
the schedule from Richie, so I've added that specific schedule as the
test_clock_jump_backward() test.
The test ordering is also (unfortunately) very strategic. Running the
selftest to the end dirties the GCL RAM, and when running
test_clock_jump_backward() once again, the GCL entries won't be all
zeroes as they were the first time around. They will contain bits and
pieces of old schedules, making it very challenging to make it fail.
Thus, test_clock_jump_backward() is the first in the test suite, and
without patch 1/4, it is only supposed to fail the _first_ time when
running after a clean boot.
====================
Vladimir Oltean [Sat, 26 Apr 2025 14:48:58 +0000 (17:48 +0300)]
selftests: net: tc_taprio: new test
Add a forwarding path test for tc-taprio, based on isochron. This is
specifically intended for NICs with an offloaded data path (switchdev/DSA)
and requires taprio 'flags 2'. Also, $h1 and $h2 must support hardware
timestamping, and $h1 tc-etf offload, for isochron to work.
Packets received by a switch while the egress port has a taprio schedule
with an open gate for the traffic class must be sent right away.
Packets received by the switch while the traffic class gate must be
delayed until it opens.
Packets received by the switch must be dropped if the gate for the
traffic class never opens.
Packets should pass if the maximum SDU for the traffic class allows it,
and should be dropped otherwise.
The schedule should auto-update itself if clock jumps take place while
taprio is installed. Repeat most of the above tests after forcing two
clock jumps, one backwards (in Jan 1970) and one back into the present.
Symlink it from tools/testing/selftests/drivers/net/dsa, because usually
DSA ports have the same MAC address, and we need STABLE_MAC_ADDRS=yes
from its forwarding.config for the test to run successfully.
Vladimir Oltean [Sat, 26 Apr 2025 14:48:57 +0000 (17:48 +0300)]
selftests: net: tsn_lib: add window_size argument to isochron_do()
Make out-of-band testing (send a packet when its traffic class gate is
closed, expecting it to be delayed) more predictable by allowing the
window size to be customized by isochron_do().
From man isochron-send, the window size alters the advance time (the
delta between the transmission time of the packet, and its expected TX
time when using SO_TXTIME or tc-taprio on the sender). In absence of the
argument, isochron-send defaults to maximizing the advance time (making
it equal to the cycle length).
The default behavior is exactly what is problematic. An advance time
that is too large will make packets intended to be out-of-band still be
potentially in-band with an open gate from the schedule's previous cycle.
We need to allow that advance time to be reduced.
Perhaps a bit confusingly, isochron_do() has a shift_time argument
currently, but that does not help here. The shift time shifts both the
user space wakeup time and the expected TX time by equal amounts, it is
unable of bringing them closer to one another.
Set the window size properly for the Ocelot PSFP selftest as well.
That used to work due to a very carefully chosen SHIFT_TIME_NS.
I've re-tested that the test still works properly.
Vladimir Oltean [Sat, 26 Apr 2025 14:48:55 +0000 (17:48 +0300)]
net: dsa: felix: fix broken taprio gate states after clock jump
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f48b ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time") Reported-by: Richie Pearn <richard.pearn@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Chad Monroe [Sun, 27 Apr 2025 01:05:44 +0000 (02:05 +0100)]
net: ethernet: mtk_eth_soc: fix SER panic with 4GB+ RAM
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Da Xue [Fri, 25 Apr 2025 19:20:09 +0000 (15:20 -0400)]
net: mdio: mux-meson-gxl: set reversed bit when using internal phy
This bit is necessary to receive packets from the internal PHY.
Without this bit set, no activity occurs on the interface.
Normally u-boot sets this bit, but if u-boot is compiled without
net support, the interface will be up but without any activity.
If bit is set once, it will work until the IP is powered down or reset.
The vendor SDK sets this bit along with the PHY_ID bits.
Simon Horman [Fri, 25 Apr 2025 15:50:47 +0000 (16:50 +0100)]
net: dlink: Correct endianness handling of led_mode
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus psrom,
as 16-bit little-endian values.
However, the integer fields of t_SROM are host byte order integers.
And in the case of led_mode this leads to a little endian value
being incorrectly treated as host byte order.
Looking at rio_set_led_mode, this does appear to be a bug as that code
masks led_mode with 0x1, 0x2 and 0x8. Logic that would be effected by a
reversed byte order.
This problem would only manifest on big endian hosts.
Found by inspection while investigating a sparse warning
regarding the crc field of t_SROM.
I believe that warning is a false positive. And although I plan
to send a follow-up to use little-endian types for other the integer
fields of PSROM_t I do not believe that will involve any bug fixes.
idpf: fix offloads support for encapsulated packets
Split offloads into csum, tso and other offloads so that tunneled
packets do not by default have all the offloads enabled.
Stateless offloads for encapsulated packets are not yet supported in
firmware/software but in the driver we were setting the features same as
non encapsulated features.
Fixed naming to clarify CSUM bits are being checked for Tx.
Inherit netdev features to VLAN interfaces as well.
Fixes: 0fe45467a104 ("idpf: add create vport and netdev configuration") Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Madhu Chittim <madhu.chittim@intel.com> Tested-by: Zachary Goldstein <zachmgoldstein@google.com> Tested-by: Samuel Salin <Samuel.salin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20250425222636.3188441-4-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xuanqiang Luo [Fri, 25 Apr 2025 22:26:32 +0000 (15:26 -0700)]
ice: Check VF VSI Pointer Value in ice_vc_add_fdir_fltr()
As mentioned in the commit baeb705fd6a7 ("ice: always check VF VSI
pointer values"), we need to perform a null pointer check on the return
value of ice_get_vf_vsi() before using it.
Fixes: 6ebbe97a4881 ("ice: Add a per-VF limit on number of FDIR filters") Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250425222636.3188441-3-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Greenwalt [Fri, 25 Apr 2025 22:26:31 +0000 (15:26 -0700)]
ice: fix Get Tx Topology AQ command error on E830
The Get Tx Topology AQ command (opcode 0x0418) has different read flag
requirements depending on the hardware/firmware. For E810, E822, and E823
firmware the read flag must be set, and for newer hardware (E825 and E830)
it must not be set.
This results in failure to configure Tx topology and the following warning
message during probe:
DDP package does not support Tx scheduling layers switching feature -
please update to the latest DDP package and try again
The current implementation only handles E825-C but not E830. It is
confusing as we first check ice_is_e825c() and then set the flag in the set
case. Finally, we check ice_is_e825c() again and set the flag for all other
hardware in both the set and get case.
Instead, notice that we always need the read flag for set, but only need
the read flag for get on E810, E822, and E823 firmware. Fix the logic to
check the MAC type and set the read flag in get only on the older devices
which require it.
Fixes: ba1124f58afd ("ice: Add E830 device IDs, MAC type and registers") Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250425222636.3188441-2-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
net_sched: Adapt qdiscs for reentrant enqueue cases
As described in Gerrard's report [1], there are cases where netem can
make the qdisc enqueue callback reentrant. Some qdiscs (drr, hfsc, ets,
qfq) break whenever the enqueue callback has reentrant behaviour.
This series addresses these issues by adding extra checks that cater for
these reentrant corner cases. This series has passed all relevant test
cases in the TDC suite.
Victor Nogueira [Fri, 25 Apr 2025 22:07:09 +0000 (19:07 -0300)]
selftests: tc-testing: Add TDC tests that exercise reentrant enqueue behaviour
Add 5 TDC tests that exercise the reentrant enqueue behaviour in drr,
ets, qfq, and hfsc:
- Test DRR's enqueue reentrant behaviour with netem (which caused a
double list add)
- Test ETS's enqueue reentrant behaviour with netem (which caused a double
list add)
- Test QFQ's enqueue reentrant behaviour with netem (which caused a double
list add)
- Test HFSC's enqueue reentrant behaviour with netem (which caused a UAF)
- Test nested DRR's enqueue reentrant behaviour with netem (which caused a
double list add)
Victor Nogueira [Fri, 25 Apr 2025 22:07:08 +0000 (19:07 -0300)]
net_sched: qfq: Fix double list add in class with netem as child qdisc
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of qfq, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
This patch checks whether the class was already added to the agg->active
list (cl_is_active) before doing the addition to cater for the reentrant
case.
Victor Nogueira [Fri, 25 Apr 2025 22:07:07 +0000 (19:07 -0300)]
net_sched: ets: Fix double list add in class with netem as child qdisc
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of ets, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether
the class was already added to the active_list (cl_is_active) before
doing the addition to cater for the reentrant case.
Victor Nogueira [Fri, 25 Apr 2025 22:07:06 +0000 (19:07 -0300)]
net_sched: hfsc: Fix a UAF vulnerability in class with netem as child qdisc
As described in Gerrard's report [1], we have a UAF case when an hfsc class
has a netem child qdisc. The crux of the issue is that hfsc is assuming
that checking for cl->qdisc->q.qlen == 0 guarantees that it hasn't inserted
the class in the vttree or eltree (which is not true for the netem
duplicate case).
This patch checks the n_active class variable to make sure that the code
won't insert the class in the vttree or eltree twice, catering for the
reentrant case.
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs") Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Victor Nogueira <victor@mojatatu.com> Link: https://patch.msgid.link/20250425220710.3964791-3-victor@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Victor Nogueira [Fri, 25 Apr 2025 22:07:05 +0000 (19:07 -0300)]
net_sched: drr: Fix double list add in class with netem as child qdisc
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of drr, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether the
class was already added to the active_list (cl_is_active) before adding
to the list to cover for the reentrant case.
The actual device uninit usually happens on a separate thread
scheduled after this code runs, but there is no guarantee of order
of thread execution, so this could be a problem. There's no
actual need to clear the client_id at this point, so simply
remove the offending code.
Fixes: 10659034c622 ("pds_core: add the aux client API") Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250425203857.71547-1-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Apr 2025 22:51:44 +0000 (15:51 -0700)]
Merge tag 'for-net-2025-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- btmtksdio: Check function enabled before doing close
- btmtksdio: Do close if SDIO card removed without close
- btusb: avoid NULL pointer dereference in skb_dequeue()
- btintel_pcie: Avoid redundant buffer allocation
- btintel_pcie: Add additional to checks to clear TX/RX paths
- hci_conn: Fix not setting conn_timeout for Broadcast Receiver
- hci_conn: Fix not setting timeout for BIG Create Sync
* tag 'for-net-2025-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: copy RX timestamp to new fragments
Bluetooth: btintel_pcie: Add additional to checks to clear TX/RX paths
Bluetooth: btmtksdio: Do close if SDIO card removed without close
Bluetooth: btmtksdio: Check function enabled before doing close
Bluetooth: btusb: avoid NULL pointer dereference in skb_dequeue()
Bluetooth: btintel_pcie: Avoid redundant buffer allocation
Bluetooth: hci_conn: Fix not setting timeout for BIG Create Sync
Bluetooth: hci_conn: Fix not setting conn_timeout for Broadcast Receiver
====================
netlink: specs: ethtool: Remove UAPI duplication of phy-upstream enum
The phy-upstream enum is already defined in the ethtool.h UAPI header
and used by the ethtool userspace tool. However, the ethtool spec does
not reference it, causing YNL to auto-generate a duplicate and redundant
enum.
Fix this by updating the spec to reference the existing UAPI enum
in ethtool.h.
When removing the clock bits for clocks which aren't used by the
Ethernet driver their names should also have been removed from the
mtk_clks_source_name array.
Remove them now as enum mtk_clks_map needs to match the
mtk_clks_source_name array so the driver can make sure that all required
clocks are present and correctly name missing clocks.
amd-xgbe: Fix to ensure dependent features are toggled with RX checksum offload
According to the XGMAC specification, enabling features such as Layer 3
and Layer 4 Packet Filtering, Split Header and Virtualized Network support
automatically selects the IPC Full Checksum Offload Engine on the receive
side.
When RX checksum offload is disabled, these dependent features must also
be disabled to prevent abnormal behavior caused by mismatched feature
dependencies.
Ensure that toggling RX checksum offload (disabling or enabling) properly
disables or enables all dependent features, maintaining consistent and
expected behavior in the network device.
Cc: stable@vger.kernel.org Fixes: 1a510ccf5869 ("amd-xgbe: Add support for VXLAN offload capabilities") Signed-off-by: Vishal Badole <Vishal.Badole@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250424130248.428865-1-Vishal.Badole@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
net: ethernet: mtk-star-emac: fix several issues on rx/tx poll
This patchset fixes two issues with the mtk-star-emac driver.
The first patch fixes spin lock recursion issues I've observed on the
Mediatek Genio 350-EVK board using this driver when the Ethernet
functionality is enabled on the board (requires a correct jumper and
DIP switch configuration, as well as enabling the device in the
devicetree).
The issues can be easily reproduced with apt install or ssh commands
especially and with the CONFIG_DEBUG_SPINLOCK parameter, when
one occurs, there is backtrace similar to this:
```
BUG: spinlock recursion on CPU#0, swapper/0/0
lock: 0xffff00000db9cf20, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.15.0-rc2-next-20250417-00001-gf6a27738686c-dirty #28 PREEMPT
Hardware name: MediaTek MT8365 Open Platform EVK (DT)
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x60/0x80
dump_stack+0x18/0x24
spin_dump+0x78/0x88
do_raw_spin_lock+0x11c/0x120
_raw_spin_lock+0x20/0x2c
mtk_star_handle_irq+0xc0/0x22c [mtk_star_emac]
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x4c/0xb0
handle_fasteoi_irq+0xa0/0x1bc
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x120
do_interrupt_handler+0x50/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
regmap_mmio_read32le+0xc/0x20 (P)
_regmap_bus_reg_read+0x6c/0xac
_regmap_read+0x60/0xdc
regmap_read+0x4c/0x80
mtk_star_rx_poll+0x2f4/0x39c [mtk_star_emac]
__napi_poll+0x38/0x188
net_rx_action+0x164/0x2c0
handle_softirqs+0x100/0x244
__do_softirq+0x14/0x20
____do_softirq+0x10/0x20
call_on_irq_stack+0x24/0x64
do_softirq_own_stack+0x1c/0x40
__irq_exit_rcu+0xd4/0x10c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
cpuidle_enter_state+0xac/0x320 (P)
cpuidle_enter+0x38/0x50
do_idle+0x1e4/0x260
cpu_startup_entry+0x34/0x3c
rest_init+0xdc/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
```
The second patch is a cleanup patch to fix a inconsistency in the
mtk_star_rx_poll function between the napi_complete_done api usage and
its description in documentation.
I've tested this patchset on Mediatek Genio 350-EVK board with a kernel
based on linux-next (tag: next-20250422).
net: ethernet: mtk-star-emac: rearm interrupts in rx_poll only when advised
In mtk_star_rx_poll function, on event processing completion, the
mtk_star_emac driver calls napi_complete_done but ignores its return
code and enable RX DMA interrupts inconditionally. This return code
gives the info if a device should avoid rearming its interrupts or not,
so fix this behaviour by taking it into account.
net: ethernet: mtk-star-emac: fix spinlock recursion issues on rx/tx poll
Use spin_lock_irqsave and spin_unlock_irqrestore instead of spin_lock
and spin_unlock in mtk_star_emac driver to avoid spinlock recursion
occurrence that can happen when enabling the DMA interrupts again in
rx/tx poll.
Justin Lai [Thu, 24 Apr 2025 04:04:44 +0000 (12:04 +0800)]
rtase: Modify the condition used to detect overflow in rtase_calc_time_mitigation
Fix the following compile error reported by the kernel test
robot by modifying the condition used to detect overflow in
rtase_calc_time_mitigation.
In file included from include/linux/mdio.h:10:0,
from drivers/net/ethernet/realtek/rtase/rtase_main.c:58:
In function 'u16_encode_bits',
inlined from 'rtase_calc_time_mitigation.constprop' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1915:13,
inlined from 'rtase_init_software_variable.isra.41' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1961:13,
inlined from 'rtase_init_one' at drivers/net/ethernet/realtek/
rtase/rtase_main.c:2111:2:
>> include/linux/bitfield.h:178:3: error: call to '__field_overflow'
declared with attribute error: value doesn't fit into mask
__field_overflow(); \
^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:198:2: note: in expansion of macro
'____MAKE_OP'
____MAKE_OP(u##size,u##size,,)
^~~~~~~~~~~
include/linux/bitfield.h:200:1: note: in expansion of macro
'__MAKE_OP'
__MAKE_OP(16)
^~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202503182158.nkAlbJWX-lkp@intel.com/ Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module") Signed-off-by: Justin Lai <justinlai0215@realtek.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250424040444.5530-1-justinlai0215@realtek.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reconfiguration of netdev may trigger close/open procedure which can
break FIFO status by adjusting the amount of empty slots for TX
timestamps. But it is not really needed because timestamps for the
packets sent over the wire still can be retrieved. On the other side,
during netdev close procedure any skbs waiting for TX timestamps can be
leaked because there is no cleaning procedure called. Free skbs waiting
for TX timestamps when closing netdev.
Fixes: 8aa2a79e9b95 ("bnxt_en: Increase the max total outstanding PTP TX packets to 4") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Vadim Fedorenko <vadfed@meta.com> Link: https://patch.msgid.link/20250424125547.460632-1-vadfed@meta.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The netdevice usage count increases during transmit queue timeouts
because netdev_hold is called in ndo_tx_timeout, scheduling a task
to reinitialize the card. Although netdev_put is called at the end
of the scheduled work, rtnl_unlock checks the reference count during
cleanup. This could cause issues if transmit timeout is called on
multiple queues.
Christian Heusel [Thu, 24 Apr 2025 14:00:28 +0000 (16:00 +0200)]
Revert "rndis_host: Flag RNDIS modems as WWAN devices"
This reverts commit 67d1a8956d2d62fe6b4c13ebabb57806098511d8. Since this
commit has been proven to be problematic for the setup of USB-tethered
ethernet connections and the related breakage is very noticeable for
users it should be reverted until a fixed version of the change can be
rolled out.
Vladimir Oltean [Thu, 24 Apr 2025 22:37:34 +0000 (01:37 +0300)]
selftests: net: bridge_vlan_aware: test untagged/8021p-tagged with and without PVID
Recent discussions around commit ad1afb003939 ("vlan_dev: VLAN 0 should
be treated as "no vlan tag" (802.1p packet)") have sparked the question
what happens with the DSA (and possibly other switchdev) data path when
the bridge says that ports should have no PVID VLAN, but the 8021q
module, as the result of a NETDEV_UP event, decides it should add VID 0
to the RX filter of those bridge ports. Do those bridge ports receive
packets tagged with VID 0 or not, now? We don't know, there is no test.
In the veth realm, this passes trivially, because veth is not VLAN
filtering and this, the 8021q module lacks the instinct to add VID 0 in
the first place.
In the realm of VLAN filtering NICs with no switchdev offload, this
should also pass, because the VLAN groups of the software bridge are
consulted, where it can clearly be seen that a PVID is missing, even
though the packet was initially accepted by the NIC.
The test only poses a challenge for switchdev drivers, which usually
have to program to hardware both VLANs from RX filtering, as well as
from switchdev. Especially when a switchdev port joins a VLAN-aware
bridge, it is unavoidable that it gains the NETIF_F_HW_VLAN_CTAG_FILTER
feature, i.e. any 8021q uppers that the bridge port may have must also
be committed to the RX filtering table of the interface. When a
VLAN-tagged packet is physically received by the port, it is initially
indistinguishable whether it will reach the bridge data path or the
8021q upper data path.
That is rather the final step of the new tests that we introduce.
We need to build context up to that stage, which means the following:
- we need to test that 802.1p (VID 0) tagged traffic is received in the
first place (on bridge ports with a valid PVID). This is the "8021p"
test.
- we need to test that the usual paths of reaching a configuration with
no PVID on a bridge port are all covered and they all reach the same
state.
Vladimir Oltean [Thu, 24 Apr 2025 22:37:33 +0000 (01:37 +0300)]
net: mscc: ocelot: delete PVID VLAN when readding it as non-PVID
The following set of commands:
ip link add br0 type bridge vlan_filtering 1 # vlan_default_pvid 1 is implicit
ip link set swp0 master br0
bridge vlan add dev swp0 vid 1
should result in the dropping of untagged and 802.1p-tagged traffic, but
we see that it continues to be accepted. Whereas, had we deleted VID 1
instead, the aforementioned dropping would have worked
This is because the ANA_PORT_DROP_CFG update logic doesn't run, because
ocelot_vlan_add() only calls ocelot_port_set_pvid() if the new VLAN has
the BRIDGE_VLAN_INFO_PVID flag.
Similar to other drivers like mt7530_port_vlan_add() which handle this
case correctly, we need to test whether the VLAN we're changing used to
have the BRIDGE_VLAN_INFO_PVID flag, but lost it now. That amounts to a
PVID deletion and should be treated as such.
Regarding blame attribution: this never worked properly since the
introduction of bridge VLAN filtering in commit 7142529f1688 ("net:
mscc: ocelot: add VLAN filtering"). However, there was a significant
paradigm shift which aligned the ANA_PORT_DROP_CFG register with the
PVID concept rather than with the native VLAN concept, and that change
wasn't targeted for 'stable'. Realistically, that is as far as this fix
needs to be propagated to.
Daniel Borkmann [Wed, 23 Apr 2025 13:36:00 +0000 (15:36 +0200)]
vmxnet3: Fix malformed packet sizing in vmxnet3_process_xdp
vmxnet3 driver's XDP handling is buggy for packet sizes using ring0 (that
is, packet sizes between 128 - 3k bytes).
We noticed MTU-related connectivity issues with Cilium's service load-
balancing in case of vmxnet3 as NIC underneath. A simple curl to a HTTP
backend service where the XDP LB was doing IPIP encap led to overly large
packet sizes but only for *some* of the packets (e.g. HTTP GET request)
while others (e.g. the prior TCP 3WHS) looked completely fine on the wire.
In fact, the pcap recording on the backend node actually revealed that the
node with the XDP LB was leaking uninitialized kernel data onto the wire
for the affected packets, for example, while the packets should have been
152 bytes their actual size was 1482 bytes, so the remainder after 152 bytes
was padded with whatever other data was in that page at the time (e.g. we
saw user/payload data from prior processed packets).
We only noticed this through an MTU issue, e.g. when the XDP LB node and
the backend node both had the same MTU (e.g. 1500) then the curl request
got dropped on the backend node's NIC given the packet was too large even
though the IPIP-encapped packet normally would never even come close to
the MTU limit. Lowering the MTU on the XDP LB (e.g. 1480) allowed to let
the curl request succeed (which also indicates that the kernel ignored the
padding, and thus the issue wasn't very user-visible).
Commit e127ce7699c1 ("vmxnet3: Fix missing reserved tailroom") was too eager
to also switch xdp_prepare_buff() from rcd->len to rbi->len. It really needs
to stick to rcd->len which is the actual packet length from the descriptor.
The latter we also feed into vmxnet3_process_xdp_small(), by the way, and
it indicates the correct length needed to initialize the xdp->{data,data_end}
parts. For e127ce7699c1 ("vmxnet3: Fix missing reserved tailroom") the
relevant part was adapting xdp_init_buff() to address the warning given the
xdp_data_hard_end() depends on xdp->frame_sz. With that fixed, traffic on
the wire looks good again.
Fixes: e127ce7699c1 ("vmxnet3: Fix missing reserved tailroom") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Andrew Sauber <andrew.sauber@isovalent.com> Cc: Anton Protopopov <aspsk@isovalent.com> Cc: William Tu <witu@nvidia.com> Cc: Martin Zaharinov <micron10@gmail.com> Cc: Ronak Doshi <ronak.doshi@broadcom.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250423133600.176689-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pauli Virtanen [Thu, 24 Apr 2025 19:51:03 +0000 (22:51 +0300)]
Bluetooth: L2CAP: copy RX timestamp to new fragments
Copy timestamp too when allocating new skb for received fragment.
Fixes missing RX timestamps with fragmentation.
Fixes: 4d7ea8ee90e4 ("Bluetooth: L2CAP: Fix handling fragmented length") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Kiran K [Sun, 20 Apr 2025 01:51:56 +0000 (07:21 +0530)]
Bluetooth: btintel_pcie: Add additional to checks to clear TX/RX paths
Due to a hardware issue, there is a possibility that the driver may miss
an MSIx interrupt on the RX/TX data path. Since the TX and RX paths are
independent, when a TX MSIx interrupt occurs, the driver can check the
RX queue for any pending data and process it if present. The same
approach applies to the RX path.
Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chris Lu [Tue, 22 Apr 2025 01:21:56 +0000 (09:21 +0800)]
Bluetooth: btmtksdio: Do close if SDIO card removed without close
To prevent Bluetooth SDIO card from be physically removed suddenly,
driver needs to ensure btmtksdio_close is called before
btmtksdio_remove to disable interrupts and txrx workqueue.
Fixes: 6ac4233afb9a ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chris Lu [Tue, 22 Apr 2025 01:21:55 +0000 (09:21 +0800)]
Bluetooth: btmtksdio: Check function enabled before doing close
Check BTMTKSDIO_FUNC_ENABLED flag before doing close to prevent
btmtksdio_close been called twice.
Fixes: 6ac4233afb9a ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The issue stems from handle_dump_pkt_qca() returning 0 even when a dump
packet is successfully processed. This is because it incorrectly
forwards the return value of hci_devcd_init() (which returns 0 on
success). As a result, the caller (btusb_recv_acl_qca() or
btusb_recv_evt_qca()) assumes the packet was not handled and passes it
to hci_recv_frame(), leading to premature kfree() of the skb.
Later, hci_devcd_rx() attempts to dequeue the same skb from the dump
queue, resulting in a NULL pointer dereference.
Fix this by:
1. Making handle_dump_pkt_qca() return 0 on success and negative errno
on failure, consistent with kernel conventions.
2. Splitting dump packet detection into separate functions for ACL
and event packets for better structure and readability.
This ensures dump packets are properly identified and consumed, avoiding
double handling and preventing NULL pointer access.
Fixes: 20981ce2d5a5 ("Bluetooth: btusb: Add WCN6855 devcoredump support") Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reuse the skb buffer provided by the PCIe driver to pass it onto the
stack, instead of copying it to a new skb.
Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Kiran K <kiran.k@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: hci_conn: Fix not setting timeout for BIG Create Sync
BIG Create Sync requires the command to just generates a status so this
makes use of __hci_cmd_sync_status_sk to wait for
HCI_EVT_LE_BIG_SYNC_ESTABLISHED, also because of this chance it is not
longer necessary to use a custom method to serialize the process of
creating the BIG sync since the cmd_work_sync itself ensures only one
command would be pending which now awaits for
HCI_EVT_LE_BIG_SYNC_ESTABLISHED before proceeding to next connection.
Fixes: 42ecf1947135 ("Bluetooth: ISO: Do not emit LE BIG Create Sync if previous is pending") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: hci_conn: Fix not setting conn_timeout for Broadcast Receiver
Broadcast Receiver requires creating PA sync but the command just
generates a status so this makes use of __hci_cmd_sync_status_sk to wait
for HCI_EV_LE_PA_SYNC_ESTABLISHED, also because of this chance it is not
longer necessary to use a custom method to serialize the process of
creating the PA sync since the cmd_work_sync itself ensures only one
command would be pending which now awaits for
HCI_EV_LE_PA_SYNC_ESTABLISHED before proceeding to next connection.
Fixes: 4a5e0ba68676 ("Bluetooth: ISO: Do not emit LE PA Create Sync if previous is pending") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chris Mi [Wed, 23 Apr 2025 08:36:11 +0000 (11:36 +0300)]
net/mlx5: E-switch, Fix error handling for enabling roce
The cited commit assumes enabling roce always succeeds. But it is
not true. Add error handling for it.
Fixes: 80f09dfc237f ("net/mlx5: Eswitch, enable RoCE loopback traffic") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/20250423083611.324567-6-mbloch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jianbo Liu [Wed, 23 Apr 2025 08:36:09 +0000 (11:36 +0300)]
net/mlx5e: TC, Continue the attr process even if encap entry is invalid
Previously the offload of the rule with header rewrite and mirror to
both internal and external destinations is skipped if the encap entry
is not valid. But it shouldn't because driver will try to offload it
again if neighbor is updated and encap entry is valid, to replace the
old FTE added for slow path. But the extra split attr doesn't exist at
that time as the process is skipped, driver then fails to offload it.
To fix this issue, remove the checking and continue the attr process
if encap entry is invalid.
Fixes: b11bde56246e ("net/mlx5e: TC, Offload rewrite and mirror to both internal and external dests") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Link: https://patch.msgid.link/20250423083611.324567-4-mbloch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maor Gottlieb [Wed, 23 Apr 2025 08:36:08 +0000 (11:36 +0300)]
net/mlx5: E-Switch, Initialize MAC Address for Default GID
Initialize the source MAC address when creating the default GID entry.
Since this entry is used only for loopback traffic, it only needs to
be a unicast address. A zeroed-out MAC address is sufficient for this
purpose.
Without this fix, random bits would be assigned as the source address.
If these bits formed a multicast address, the firmware would return an
error, preventing the user from switching to switchdev mode:
Symbolic (e.g. "vxlan") and custom (e.g. "tunnel_header_0") tunnels
cannot be combined, but the match params interface does not have fields
for matching on vxlan gbp. To match vxlan bgp, the tc_tun layer uses
tunnel_header_0.
Allow matching on both VNI and GBP by matching the VNI with a custom
tunnel header instead of the symbolic field name.
Matching solely on the VNI continues to use the symbolic field name.
Fixes: 74a778b4a63f ("net/mlx5: HWS, added definers handling") Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com> Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/20250423083611.324567-2-mbloch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move rx_lock from xsk_socket to xsk_buff_pool.
Fix synchronization for shared umem mode in
generic RX path where multiple sockets share
single xsk_buff_pool.
RX queue is exclusive to xsk_socket, while FILL
queue can be shared between multiple sockets.
This could result in race condition where two
CPU cores access RX path of two different sockets
sharing the same umem.
Protect both queues by acquiring spinlock in shared
xsk_buff_pool.
Lock contention may be minimized in the future by some
per-thread FQ buffering.
It's safe and necessary to move spin_lock_bh(rx_lock)
after xsk_rcv_check():
* xs->pool and spinlock_init is synchronized by
xsk_bind() -> xsk_is_bound() memory barriers.
* xsk_rcv_check() may return true at the moment
of xsk_release() or xsk_unbind_dev(),
however this will not cause any data races or
race conditions. xsk_unbind_dev() removes xdp
socket from all maps and waits for completion
of all outstanding rx operations. Packets in
RX path will either complete safely or drop.
vxlan: vnifilter: Fix unlocked deletion of default FDB entry
When a VNI is deleted from a VXLAN device in 'vnifilter' mode, the FDB
entry associated with the default remote (assuming one was configured)
is deleted without holding the hash lock. This is wrong and will result
in a warning [1] being generated by the lockdep annotation that was
added by commit ebe642067455 ("vxlan: Create wrappers for FDB lookup").
Reproducer:
# ip link add vx0 up type vxlan dstport 4789 external vnifilter local 192.0.2.1
# bridge vni add vni 10010 remote 198.51.100.1 dev vx0
# bridge vni del vni 10010 dev vx0
Fix by acquiring the hash lock before the deletion and releasing it
afterwards. Blame the original commit that introduced the issue rather
than the one that exposed it.
Jakub Kicinski [Thu, 24 Apr 2025 18:10:57 +0000 (11:10 -0700)]
Merge tag 'wireless-2025-04-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Some more fixes, notably:
* iwlwifi: various regression and iwlmld fixes
* mac80211: fix TX frames in monitor mode
* brcmfmac: error handling for firmware load
* tag 'wireless-2025-04-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: restore missing initialization of async_handlers_list
wifi: brcm80211: fmac: Add error handling for brcmf_usb_dl_writeimage()
wifi: plfxlc: Remove erroneous assert in plfxlc_mac_release
wifi: iwlwifi: fix the check for the SCRATCH register upon resume
wifi: iwlwifi: don't warn if the NIC is gone in resume
wifi: iwlwifi: mld: fix BAID validity check
wifi: iwlwifi: back off on continuous errors
wifi: iwlwifi: mld: only create debugfs symlink if it does not exist
wifi: iwlwifi: mld: inform trans on init failure
wifi: iwlwifi: mld: properly handle async notification in op mode start
Revert "wifi: iwlwifi: make no_160 more generic"
Revert "wifi: iwlwifi: add support for BE213"
wifi: mac80211: restore monitor for outgoing frames
====================
Merge tag 'v6.15-p5' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Revert acomp multibuffer tests which were buggy
- Fix off-by-one regression in new scomp code
- Lower quality setting on atmel-sha204a as it may not be random
* tag 'v6.15-p5' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: atmel-sha204a - Set hwrng quality to lowest possible
crypto: scomp - Fix off-by-one bug when calculating last page
Revert "crypto: testmgr - Add multibuffer acomp testing"
====================
net: stmmac: fix timestamp snapshots on dwmac1000
this is the v2 of a small series containing two small fixes for the
timestamp snapshot feature on stmmac, especially on dwmac1000 version.
Those issues have been detected on a socfpga (Cyclone V) platform. They
kind of follow the big rework sent by Maxime at the end of last year to
properly split this feature support between different versions of the
DWMAC IP.
net: stmmac: fix multiplication overflow when reading timestamp
The current way of reading a timestamp snapshot in stmmac can lead to
integer overflow, as the computation is done on 32 bits. The issue has
been observed on a dwmac-socfpga platform returning chaotic timestamp
values due to this overflow. The corresponding multiplication is done
with a MUL instruction, which returns 32 bit values. Explicitly casting
the value to 64 bits replaced the MUL with a UMLAL, which computes and
returns the result on 64 bits, and so returns correctly the timestamps.
Prevent this overflow by explicitly casting the intermediate value to
u64 to make sure that the whole computation is made on u64. While at it,
apply the same cast on the other dwmac variant (GMAC4) method for
snapshot retrieval.
net: stmmac: fix dwmac1000 ptp timestamp status offset
When a PTP interrupt occurs, the driver accesses the wrong offset to
learn about the number of available snapshots in the FIFO for dwmac1000:
it should be accessing bits 29..25, while it is currently reading bits
19..16 (those are bits about the auxiliary triggers which have generated
the timestamps). As a consequence, it does not compute correctly the
number of available snapshots, and so possibly do not generate the
corresponding clock events if the bogus value ends up being 0.
Fix clock events generation by reading the correct bits in the timestamp
register for dwmac1000.
Shannon Nelson [Mon, 21 Apr 2025 17:46:06 +0000 (10:46 -0700)]
pds_core: make wait_context part of q_info
Make the wait_context a full part of the q_info struct rather
than a stack variable that goes away after pdsc_adminq_post()
is done so that the context is still available after the wait
loop has given up.
There was a case where a slow development firmware caused
the adminq request to time out, but then later the FW finally
finished the request and sent the interrupt. The handler tried
to complete_all() the completion context that had been created
on the stack in pdsc_adminq_post() but no longer existed.
This caused bad pointer usage, kernel crashes, and much wailing
and gnashing of teeth.
Fixes: 01ba61b55b20 ("pds_core: Add adminq processing and commands") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-5-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pds_core: Remove unnecessary check in pds_client_adminq_cmd()
When the pds_core driver was first created there were some race
conditions around using the adminq, especially for client drivers.
To reduce the possibility of a race condition there's a check
against pf->state in pds_client_adminq_cmd(). This is problematic
for a couple of reasons:
1. The PDSC_S_INITING_DRIVER bit is set during probe, but not
cleared until after everything in probe is complete, which
includes creating the auxiliary devices. For pds_fwctl this
means it can't make any adminq commands until after pds_core's
probe is complete even though the adminq is fully up by the
time pds_fwctl's auxiliary device is created.
2. The race conditions around using the adminq have been fixed
and this path is already protected against client drivers
calling pds_client_adminq_cmd() if the adminq isn't ready,
i.e. see pdsc_adminq_post() -> pdsc_adminq_inc_if_up().
Fix this by removing the pf->state check in pds_client_adminq_cmd()
because invalid accesses to pds_core's adminq is already handled by
pdsc_adminq_post()->pdsc_adminq_inc_if_up().
Fixes: 10659034c622 ("pds_core: add the aux client API") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-4-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pds_core: handle unsupported PDS_CORE_CMD_FW_CONTROL result
If the FW doesn't support the PDS_CORE_CMD_FW_CONTROL command
the driver might at the least print garbage and at the worst
crash when the user runs the "devlink dev info" devlink command.
This happens because the stack variable fw_list is not 0
initialized which results in fw_list.num_fw_slots being a
garbage value from the stack. Then the driver tries to access
fw_list.fw_names[i] with i >= ARRAY_SIZE and runs off the end
of the array.
Fix this by initializing the fw_list and by not failing
completely if the devcmd fails because other useful information
is printed via devlink dev info even if the devcmd fails.
Fixes: 45d76f492938 ("pds_core: set up device and adminq") Signed-off-by: Brett Creeley <brett.creeley@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-3-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pds_core: Prevent possible adminq overflow/stuck condition
The pds_core's adminq is protected by the adminq_lock, which prevents
more than 1 command to be posted onto it at any one time. This makes it
so the client drivers cannot simultaneously post adminq commands.
However, the completions happen in a different context, which means
multiple adminq commands can be posted sequentially and all waiting
on completion.
On the FW side, the backing adminq request queue is only 16 entries
long and the retry mechanism and/or overflow/stuck prevention is
lacking. This can cause the adminq to get stuck, so commands are no
longer processed and completions are no longer sent by the FW.
As an initial fix, prevent more than 16 outstanding adminq commands so
there's no way to cause the adminq from getting stuck. This works
because the backing adminq request queue will never have more than 16
pending adminq commands, so it will never overflow. This is done by
reducing the adminq depth to 16.
Fixes: 45d76f492938 ("pds_core: set up device and adminq") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250421174606.3892-2-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Golle [Tue, 22 Apr 2025 03:10:20 +0000 (04:10 +0100)]
net: dsa: mt7530: sync driver-specific behavior of MT7531 variants
MT7531 standalone and MMIO variants found in MT7988 and EN7581 share
most basic properties. Despite that, assisted_learning_on_cpu_port and
mtu_enforcement_ingress were only applied for MT7531 but not for MT7988
or EN7581, causing the expected issues on MMIO devices.
Apply both settings equally also for MT7988 and EN7581 by moving both
assignments form mt7531_setup() to mt7531_setup_common().
This fixes unwanted flooding of packets due to unknown unicast
during DA lookup, as well as issues with heterogenous MTU settings.
====================
net_sched: Fix UAF vulnerability in HFSC qdisc
This patchset contains two bug fixes and a selftest for the first one
which we have a reliable reproducer, please check each patch
description for details.
====================
Cong Wang [Thu, 17 Apr 2025 18:47:32 +0000 (11:47 -0700)]
selftests/tc-testing: Add test for HFSC queue emptying during peek operation
Add a selftest to exercise the condition where qdisc implementations
like netem or codel might empty the queue during a peek operation.
This tests the defensive code path in HFSC that checks the queue length
again after peeking to handle this case.
Based on the reproducer from Gerrard, improved by Jamal.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Tested-by: Victor Nogueira <victor@mojatatu.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20250417184732.943057-4-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cong Wang [Thu, 17 Apr 2025 18:47:30 +0000 (11:47 -0700)]
net_sched: hfsc: Fix a UAF vulnerability in class handling
This patch fixes a Use-After-Free vulnerability in the HFSC qdisc class
handling. The issue occurs due to a time-of-check/time-of-use condition
in hfsc_change_class() when working with certain child qdiscs like netem
or codel.
The vulnerability works as follows:
1. hfsc_change_class() checks if a class has packets (q.qlen != 0)
2. It then calls qdisc_peek_len(), which for certain qdiscs (e.g.,
codel, netem) might drop packets and empty the queue
3. The code continues assuming the queue is still non-empty, adding
the class to vttree
4. This breaks HFSC scheduler assumptions that only non-empty classes
are in vttree
5. Later, when the class is destroyed, this can lead to a Use-After-Free
The fix adds a second queue length check after qdisc_peek_len() to verify
the queue wasn't emptied.
Fixes: 21f4d5cc25ec ("net_sched/hfsc: fix curve activation in hfsc_change_class()") Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Reviewed-by: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20250417184732.943057-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
selftests: mptcp: diag: use mptcp_lib_get_info_value
When running diag.sh in a loop, chk_dump_one will report the following
"grep: write error":
13 ....chk 2 cestab [ OK ]
grep: write error
14 ....chk dump_one [ OK ]
15 ....chk 2->0 msk in use after flush [ OK ]
16 ....chk 2->0 cestab after flush [ OK ]
This error is caused by a broken pipe. When the output of 'ss' is processed
by grep, 'head -n 1' will exit immediately after getting the first line,
causing the subsequent pipe to close. At this time, if 'grep' is still
trying to write data to the closed pipe, it will trigger a SIGPIPE signal,
causing a write error.
One solution is not to use this problematic "head -n 1" command, but to use
mptcp_lib_get_info_value() helper defined in mptcp_lib.sh to get the value
of 'token'.
Fixes: ba2400166570 ("selftests: mptcp: add a test for mptcp_diag_dump_one") Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Tested-by: Gang Yan <yangang@kylinos.cn> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250421-net-mptcp-pm-defer-freeing-v1-2-e731dc6e86b9@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau [Mon, 21 Apr 2025 17:07:13 +0000 (19:07 +0200)]
mptcp: pm: Defer freeing of MPTCP userspace path manager entries
When path manager entries are deleted from the local address list, they
are first unlinked from the address list using list_del_rcu(). The
entries must not be freed until after the RCU grace period, but the
existing code immediately frees the entry.
Use kfree_rcu_mightsleep() and adjust sk_omem_alloc in open code instead
of using the sock_kfree_s() helper. This code path is only called in a
netlink handler, so the "might sleep" function is preferable to adding
a rarely-used rcu_head member to struct mptcp_pm_addr_entry.
Fixes: 88d097316371 ("mptcp: drop free_list for deleting entries") Cc: stable@vger.kernel.org Signed-off-by: Mat Martineau <martineau@kernel.org> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250421-net-mptcp-pm-defer-freeing-v1-1-e731dc6e86b9@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix mis-uses of 'cc-option' for warning disablement
This was triggered by one of my mis-uses causing odd build warnings on
sparc in linux-next, but while figuring out why the "obviously correct"
use of cc-option caused such odd breakage, I found eight other cases of
the same thing in the tree.
The root cause is that 'cc-option' doesn't work for checking negative
warning options (ie things like '-Wno-stringop-overflow') because gcc
will silently accept options it doesn't recognize, and so 'cc-option'
ends up thinking they are perfectly fine.
And it all works, until you have a situation where _another_ warning is
emitted. At that point the compiler will go "Hmm, maybe the user
intended to disable this warning but used that wrong option that I
didn't recognize", and generate a warning for the unrecognized negative
option.
Which explains why we have several cases of this in the tree: the
'cc-option' test really doesn't work for this situation, but most of the
time it simply doesn't matter that ity doesn't work.
The reason my recently added case caused problems on sparc was pointed
out by Thomas Weißschuh: the sparc build had a previous explicit warning
that then triggered the new one.
I think the best fix for this would be to make 'cc-option' a bit smarter
about this sitation, possibly by adding an intentional warning to the
test case that then triggers the unrecognized option warning reliably.
But the short-term fix is to replace 'cc-option' with an existing helper
designed for this exact case: 'cc-disable-warning', which picks the
negative warning but uses the positive form for testing the compiler
support.
locking/local_lock: fix _Generic() matching of local_trylock_t
Michael Larabel reported [1] a nginx performance regression in v6.15-rc3
and bisected it to commit 51339d99c013 ("locking/local_lock, mm: replace
localtry_ helpers with local_trylock_t type")
The problem is the _Generic() usage with a default association that
masks the fact that "local_trylock_t *" association is not being
selected as expected. Replacing the default with the only other
expected type "local_lock_t *" reveals the underlying problem:
include/linux/local_lock_internal.h:174:26: error: ‘_Generic’ selector of type ‘__seg_gs local_lock_t *’ is not compatible with any association
The local_locki's are part of __percpu structures and thus the __percpu
attribute is needed to associate the type properly. Add the attribute
and keep the default replaced to turn any further mismatches into
compile errors.
The failure to recognize local_try_lock_t in __local_lock_release()
means that a local_trylock[_irqsave]() operation will set tl->acquired
to 1 (there's no _Generic() part in the trylock code), but then
local_unlock[_irqrestore]() will not set tl->acquired back to 0, so
further trylock operations will always fail on the same cpu+lock, while
non-trylock operations continue to work - a lockdep_assert() is also not
being executed in the _Generic() part of local_lock() code.
This means consume_stock() and refill_stock() operations will fail
deterministically, resulting in taking the slow paths and worse
performance.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-scsi: Fix vhost_scsi_send_status()
vhost-scsi: Fix vhost_scsi_send_bad_target()
vhost-scsi: protect vq->log_used with vq->mutex
vhost_task: fix vhost_task_create() documentation
virtio_console: fix order of fields cols and rows
virtio_console: fix missing byte order handling for cols and rows
virtgpu: don't reset on shutdown
virtio_ring: Fix data race by tagging event_triggered as racy for KCSAN
vhost: fix VHOST_*_OWNER documentation
virtio_pci: Use self group type for cap commands
wifi: iwlwifi: restore missing initialization of async_handlers_list
The initialization of async_handlers_list
was accidentally removed in a previous change.
This patch restores the missing initialization
to ensure proper handler registration.
wifi: brcm80211: fmac: Add error handling for brcmf_usb_dl_writeimage()
The function brcmf_usb_dl_writeimage() calls the function
brcmf_usb_dl_cmd() but dose not check its return value. The
'state.state' and the 'state.bytes' are uninitialized if the
function brcmf_usb_dl_cmd() fails. It is dangerous to use
uninitialized variables in the conditions.
Add error handling for brcmf_usb_dl_cmd() to jump to error
handling path if the brcmf_usb_dl_cmd() fails and the
'state.state' and the 'state.bytes' are uninitialized.
Improve the error message to report more detailed error
information.
Fixes: 71bb244ba2fd ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Link: https://patch.msgid.link/20250422042203.2259-1-vulab@iscas.ac.cn Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Murad Masimov [Fri, 21 Mar 2025 18:52:25 +0000 (21:52 +0300)]
wifi: plfxlc: Remove erroneous assert in plfxlc_mac_release
plfxlc_mac_release() asserts that mac->lock is held. This assertion is
incorrect, because even if it was possible, it would not be the valid
behaviour. The function is used when probe fails or after the device is
disconnected. In both cases mac->lock can not be held as the driver is
not working with the device at the moment. All functions that use mac->lock
unlock it just after it was held. There is also no need to hold mac->lock
for plfxlc_mac_release() itself, as mac data is not affected, except for
mac->flags, which is modified atomically.
wifi: iwlwifi: fix the check for the SCRATCH register upon resume
We can't rely on the SCRATCH register being 0 on platform that power
gate the NIC in S3. Even in those platforms, the SCRATCH register is
still returning 0x1010000.
Make sure that we understand that those platforms have powered off the
device.
wifi: iwlwifi: don't warn if the NIC is gone in resume
Some BIOSes decide to power gate the WLAN device during S3. Since
iwlwifi doesn't expect this, it gets very noisy reporting that the
device is no longer available. Wifi is still available because iwlwifi
recovers, but it spews scary prints in the log.
Johannes Berg [Sun, 20 Apr 2025 06:59:59 +0000 (09:59 +0300)]
wifi: iwlwifi: mld: fix BAID validity check
Perhaps IWL_FW_CHECK() is a bit misnamed, but it just returns
the value of the inner condition. Therefore, the current code
skips the actual function when it has the BAID data and makes
it crash later when it doesn't. Fix the logic.
Johannes Berg [Sun, 20 Apr 2025 06:59:58 +0000 (09:59 +0300)]
wifi: iwlwifi: back off on continuous errors
When errors occur repeatedly, the driver shouldn't go into a
tight loop trying to reset the device. Implement the backoff
I had already defined IWL_TRANS_RESET_DELAY for, but clearly
forgotten the implementation of.
Benjamin Berg [Sun, 20 Apr 2025 06:59:57 +0000 (09:59 +0300)]
wifi: iwlwifi: mld: only create debugfs symlink if it does not exist
When mac80211 switches between non-MLO and MLO it will recreate the
debugfs directories. This results in the add_if_debugfs handler being
called multiple times. As the convenience symlink is created in the mld
debugfs directory and not the vif, it will not be removed by mac80211
when this happens and still exists.
Add a check and only create the convenience symlink if we have not yet
done so.
If starting the op mode failed, the opmode memory is being freed,
so trans->op_mode needs to be NULLified. Otherwise, trans will access
already freed memory.
Call iwl_trans_op_mode_leave in that case.
wifi: iwlwifi: mld: properly handle async notification in op mode start
From the moment that we have ALIVE, we can receive notification that
are handled asynchronously.
Some notifications (for example iwl_rfi_support_notif) requires an
operational FW. So we need to make sure that they were handled in
iwl_op_mode_mld_start before we stop the FW. Flush the async_handlers_wk
there to achieve that.
Also, if loading the FW in op mode start failed, we need to cancel
these notifications, as they are from a dead FW.
More than that, not doing so can cause us to access freed memory
if async_handlers_wk is executed after ieee80211_free_hw is called.
Fix this by canceling all async notifications if a failure occurred in
init (after ALIVE).
The indication of the BW limitation in the sub-device ID is not applicable
for Killer devices. For those devices, bw_limit will hold a random value,
so a matching dev_info might not be found, which leads to a probe
failure.
Until it is properly fixed, revert this.
This device needs commit 75a3313f52b7 ("wifi: iwlwifi: make no_160 more generic"),
which has a bug and is being reverted until it is fixed.
Since this device wasn't shipped yet it is ok to not support it.
Change hardware configuration for the NETSYSv3.
- Enable PSE dummy page mechanism for the GDM1/2/3
- Enable PSE drop mechanism when the WDMA Rx ring full
- Enable PSE no-drop mechanism for packets from the WDMA Tx
- Correct PSE free drop threshold
- Correct PSE CDMA high threshold
There is a racing condition between workqueue created when enabling
bearer and another thread created when disabling bearer right after
that as follow:
Fixes: da001fb651b00e1d ("crypto: atmel-i2c - add support for SHA204A random number generator") Cc: <stable@vger.kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Mon, 21 Apr 2025 03:31:31 +0000 (11:31 +0800)]
crypto: scomp - Fix off-by-one bug when calculating last page
Fix off-by-one bug in the last page calculation for src and dst.
Reported-by: Nhat Pham <nphamcs@gmail.com> Fixes: 2d3553ecb4e3 ("crypto: scomp - Remove support for some non-trivial SG lists") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
virtio-net: disable delayed refill when pausing rx
When pausing rx (e.g. set up xdp, xsk pool, rx resize), we call
napi_disable() on the receive queue's napi. In delayed refill_work, it
also calls napi_disable() on the receive queue's napi. When
napi_disable() is called on an already disabled napi, it will sleep in
napi_disable_locked while still holding the netdev_lock. As a result,
later napi_enable gets stuck too as it cannot acquire the netdev_lock.
This leads to refill_work and the pause-then-resume tx are stuck
altogether.
This scenario can be reproducible by binding a XDP socket to virtio-net
interface without setting up the fill ring. As a result, try_fill_recv
will fail until the fill ring is set up and refill_work is scheduled.
This commit adds virtnet_rx_(pause/resume)_all helpers and fixes up the
virtnet_rx_resume to disable future and cancel all inflights delayed
refill_work before calling napi_disable() to pause the rx.
Fixes: 413f0271f396 ("net: protect NAPI enablement with netdev_lock()") Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://patch.msgid.link/20250417072806.18660-2-minhquangbui99@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Qingfang Deng [Thu, 17 Apr 2025 03:25:56 +0000 (11:25 +0800)]
net: phy: leds: fix memory leak
A network restart test on a router led to an out-of-memory condition,
which was traced to a memory leak in the PHY LED trigger code.
The root cause is misuse of the devm API. The registration function
(phy_led_triggers_register) is called from phy_attach_direct, not
phy_probe, and the unregister function (phy_led_triggers_unregister)
is called from phy_detach, not phy_remove. This means the register and
unregister functions can be called multiple times for the same PHY
device, but devm-allocated memory is not freed until the driver is
unbound.
This also prevents kmemleak from detecting the leak, as the devm API
internally stores the allocated pointer.
Fix this by replacing devm_kzalloc/devm_kcalloc with standard
kzalloc/kcalloc, and add the corresponding kfree calls in the unregister
path.
Fixes: 3928ee6485a3 ("net: phy: leds: Add support for "link" trigger") Fixes: 2e0bc452f472 ("net: phy: leds: add support for led triggers on phy link state change") Signed-off-by: Hao Guan <hao.guan@siflower.com.cn> Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250417032557.2929427-1-dqfext@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As a result of an email from the fbnic author, I reviewed the phylink
documentation, and I have decided to clarify the wording in the
mac_link_(up|down)() kernel documentation as this was written from the
point of view of mvneta/mvpp2 and is misleading.
The documentation talks about forcing the link - indeed, this is what
is done in the mvneta and mvpp2 drivers but not at the physical layer
but the MACs idea, which has the effect of only allowing or stopping
packet flow at the MAC. This "link" needs to be controlled when using
a PHY or fixed link to start or stop packet flow at the MAC. However,
as the MAC and PCS are tightly integrated, if the MACs idea of the
link is forced down, it has the side effect that there is no way to
determine that the media link has come up - in this mode, the MAC must
be allowed to follow its built-in PCS so we can read the link state.
Frame the documentation in more generic terms, to avoid the thought
that the physical media link to the partner needs in some way to be
forced up or down with these calls; it does not. If that were to be
done, it would be a self-fulfilling prophecy - e.g. if the media link
goes down, then mac_link_down() will be called, and if the media link
is then placed into a forced down state, there is no possibility
that the media link will ever come up again - clearly this is a wrong
interpretation.
These methods are notifications to the MAC about what has happened to
the media link state - either from the PHY, or a PCS, or whatever
mechanism fixed-link is using. Thus, reword them to get away from
talking about changing link state to avoid confusion with media link
state.
This is not a change of any requirements of these methods.
Also, remove the obsolete references to EEE for these methods, we now
have the LPI functions for configuring the EEE parameters which
renders this redundant, and also makes the passing of "phy" to the
mac_link_up() function obsolete.
projects / thirdparty / linux.git / log
