The init_systime() may be invoked in atomic state. We have observed the
following call trace when running "phc_ctl /dev/ptp0 set" on a Intel
Agilex board.
BUG: sleeping function called from invalid context at drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:74
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 381, name: phc_ctl
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
Preemption disabled at:
[<ffff80000892ef78>] stmmac_set_time+0x34/0x8c
CPU: 2 PID: 381 Comm: phc_ctl Not tainted 5.18.0-rc2-next-20220414-yocto-standard+ #567
Hardware name: SoCFPGA Agilex SoCDK (DT)
Call trace:
dump_backtrace.part.0+0xc4/0xd0
show_stack+0x24/0x40
dump_stack_lvl+0x7c/0xa0
dump_stack+0x18/0x34
__might_resched+0x154/0x1c0
__might_sleep+0x58/0x90
init_systime+0x78/0x120
stmmac_set_time+0x64/0x8c
ptp_clock_settime+0x60/0x9c
pc_clock_settime+0x6c/0xc0
__arm64_sys_clock_settime+0x88/0xf0
invoke_syscall+0x5c/0x130
el0_svc_common.constprop.0+0x4c/0x100
do_el0_svc+0x7c/0xa0
el0_svc+0x58/0xcc
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x18c/0x190
So we should use readl_poll_timeout_atomic() here instead of
readl_poll_timeout().
Also adjust the delay time to 10us to fix a "__bad_udelay" build error
reported by "kernel test robot <lkp@intel.com>". I have tested this on
Intel Agilex and NXP S32G boards, there is no delay needed at all.
So the 10us delay should be long enough for most cases.
Fixes: ff8ed737860e ("net: stmmac: use readl_poll_timeout() function in init_systime()") Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
netlink_dump() is allocating an skb, reserves space in it
but forgets to reset network header.
This allows a BPF program, invoked later from sk_filter()
to access uninitialized kernel memory from the reserved
space.
Theorically mac header reset could be omitted, because
it is set to a special initial value.
bpf_internal_load_pointer_neg_helper calls skb_mac_header()
without checking skb_mac_header_was_set().
Relying on skb->len not being too big seems fragile.
We also could add a sanity check in bpf_internal_load_pointer_neg_helper()
to avoid surprises in the future.
Reads and Writes to ip6_rt_gc_expire always have been racy,
as syzbot reported lately [1]
There is a possible risk of under-flow, leading
to unexpected high value passed to fib6_run_gc(),
although I have not observed this in the field.
Hosts hitting ip6_dst_gc() very hard are under pretty bad
state anyway.
[1]
BUG: KCSAN: data-race in ip6_dst_gc / ip6_dst_gc
read-write to 0xffff888102110744 of 4 bytes by task 13165 on cpu 1:
ip6_dst_gc+0x1f3/0x220 net/ipv6/route.c:3311
dst_alloc+0x9b/0x160 net/core/dst.c:86
ip6_dst_alloc net/ipv6/route.c:344 [inline]
icmp6_dst_alloc+0xb2/0x360 net/ipv6/route.c:3261
mld_sendpack+0x2b9/0x580 net/ipv6/mcast.c:1807
mld_send_cr net/ipv6/mcast.c:2119 [inline]
mld_ifc_work+0x576/0x800 net/ipv6/mcast.c:2651
process_one_work+0x3d3/0x720 kernel/workqueue.c:2289
worker_thread+0x618/0xa70 kernel/workqueue.c:2436
kthread+0x1a9/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30
read-write to 0xffff888102110744 of 4 bytes by task 11607 on cpu 0:
ip6_dst_gc+0x1f3/0x220 net/ipv6/route.c:3311
dst_alloc+0x9b/0x160 net/core/dst.c:86
ip6_dst_alloc net/ipv6/route.c:344 [inline]
icmp6_dst_alloc+0xb2/0x360 net/ipv6/route.c:3261
mld_sendpack+0x2b9/0x580 net/ipv6/mcast.c:1807
mld_send_cr net/ipv6/mcast.c:2119 [inline]
mld_ifc_work+0x576/0x800 net/ipv6/mcast.c:2651
process_one_work+0x3d3/0x720 kernel/workqueue.c:2289
worker_thread+0x618/0xa70 kernel/workqueue.c:2436
kthread+0x1a9/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30
value changed: 0x00000bb3 -> 0x00000ba9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 11607 Comm: kworker/0:21 Not tainted 5.18.0-rc1-syzkaller-00037-g42e7a03d3bad-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: mld mld_ifc_work
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220413181333.649424-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While investigating a related syzbot report,
I found that whenever call to tcf_exts_init()
from u32_init_knode() is failing, we end up
with an elevated refcount on ht->refcnt
To avoid that, only increase the refcount after
all possible errors have been evaluated.
Fixes: b9a24bb76bf6 ("net_sched: properly handle failure case of tcf_exts_init()") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. During ip6gretap device initialization, tunnel->tun_hlen (e.g. 4) is
calculated based on old flags (see ip6gre_calc_hlen());
2. packet_snd() reserves header room for skb A, assuming
tunnel->tun_hlen is 4;
3. Later (in clsact Qdisc), the eBPF program sets a new tunnel key for
skb A using bpf_skb_set_tunnel_key() (see _ip6gretap_set_tunnel());
4. __gre6_xmit() detects the new tunnel key, and recalculates
"tun_hlen" (e.g. 12) based on new flags (e.g. TUNNEL_KEY and
TUNNEL_SEQ);
5. gre_build_header() calls skb_push() with insufficient reserved header
room, triggering the BUG.
As sugguested by Cong, fix it by moving the call to skb_cow_head() after
the recalculation of tun_hlen.
ip netns add at_ns0
ip link add veth0 type veth peer name veth1
ip link set veth0 netns at_ns0
ip netns exec at_ns0 ip addr add 172.16.1.100/24 dev veth0
ip netns exec at_ns0 ip link set dev veth0 up
ip link set dev veth1 up mtu 1500
ip addr add dev veth1 172.16.1.200/24
ip netns exec at_ns0 ip addr add ::11/96 dev veth0
ip netns exec at_ns0 ip link set dev veth0 up
ip addr add dev veth1 ::22/96
ip link set dev veth1 up
ip netns exec at_ns0 \
ip link add dev ip6gretap00 type ip6gretap seq flowlabel 0xbcdef key 2 \
local ::11 remote ::22
ip netns exec at_ns0 ip addr add dev ip6gretap00 10.1.1.100/24
ip netns exec at_ns0 ip addr add dev ip6gretap00 fc80::100/96
ip netns exec at_ns0 ip link set dev ip6gretap00 up
ip link add dev ip6gretap11 type ip6gretap external
ip addr add dev ip6gretap11 10.1.1.200/24
ip addr add dev ip6gretap11 fc80::200/24
ip link set dev ip6gretap11 up
tc qdisc add dev ip6gretap11 clsact
tc filter add dev ip6gretap11 egress bpf da obj $OBJ sec ip6gretap_set_tunnel
tc filter add dev ip6gretap11 ingress bpf da obj $OBJ sec ip6gretap_get_tunnel
ping6 -c 3 -w 10 -q ::11
Fixes: 6712abc168eb ("ip6_gre: add ip6 gre and gretap collect_md mode") Reported-by: Feng Zhou <zhoufeng.zf@bytedance.com> Co-developed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not update tunnel->tun_hlen in data plane code. Use a local variable
instead, just like "tunnel_hlen" in net/ipv4/ip_gre.c:gre_fb_xmit().
Co-developed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
packet_sock xmit could be dev_queue_xmit, which also returns negative
errors. So only checking positive errors is not enough, or userspace
sendmsg may return success while packet is not send out.
Move the net_xmit_errno() assignment in the braces as checkpatch.pl said
do not use assignment in if condition.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit e5d5aadcf3cd ("net/smc: fix sk_refcnt underflow on linkdown
and fallback"), for a fallback connection, __smc_release() does not call
sock_put() if its state is already SMC_CLOSED.
When calling smc_shutdown() after falling back, its state is set to
SMC_CLOSED but does not call sock_put(), so this patch calls it.
Reported-and-tested-by: syzbot+6e29a053eb165bd50de5@syzkaller.appspotmail.com Fixes: e5d5aadcf3cd ("net/smc: fix sk_refcnt underflow on linkdown and fallback") Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A recent patch[1] from Eric Dumazet flipped the order in which the
keepalive timer and the keepalive worker were cancelled in order to fix a
syzbot reported issue[2]. Unfortunately, this enables the mirror image bug
whereby the timer races with rxrpc_exit_net(), restarting the worker after
it has been cancelled:
CPU 1 CPU 2
=============== =====================
if (rxnet->live)
<INTERRUPT>
rxnet->live = false;
cancel_work_sync(&rxnet->peer_keepalive_work);
rxrpc_queue_work(&rxnet->peer_keepalive_work);
del_timer_sync(&rxnet->peer_keepalive_timer);
Fix this by restoring the removed del_timer_sync() so that we try to remove
the timer twice. If the timer runs again, it should see ->live == false
and not restart the worker.
Replace usleep_range() method with udelay() method to allow atomic contexts
in low-level MDIO access functions.
The following issue can be seen by doing the following:
$ modprobe -r bonding
$ modprobe -v bonding max_bonds=1 mode=1 miimon=100 use_carrier=0
$ ip link set bond0 up
$ ifenslave bond0 eth0 eth1
An infinite loop may occur if we fail to acquire the HW semaphore,
which is needed for resource release.
This will typically happen if the hardware is surprise-removed.
At this stage there is nothing to do, except log an error and quit.
Commit ebe48d368e97 ("esp: Fix possible buffer overflow in ESP
transformation") tried to fix skb_page_frag_refill usage in ESP by
capping allocsize to 32k, but that doesn't completely solve the issue,
as skb_page_frag_refill may return a single page. If that happens, we
will write out of bounds, despite the check introduced in the previous
patch.
This patch forces COW in cases where we would end up calling
skb_page_frag_refill with a size larger than a page (first in
esp_output_head with tailen, then in esp_output_tail with
skb->data_len).
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
We fix it:
1) Replacing it with pm_runtime_resume_and_get to keep usage counter
balanced.
2) Add putting operation before returning error.
SIDO(Single-Inductor Dual-Ouput) Buck powers up both analog and digital
circuits along with internal memory, powering off this is the last thing
that codec should do when going to very low power.
Current code was powering off this Buck if there are no users of sysclk,
which is not correct. Powering off this buck will result in no register access.
This code path was never tested until recently after adding pm support
in SoundWire controller. Fix this by removing the buck poweroff when the
codec is active and also the code that is not used.
Without this patch all the read/write transactions will never complete and
results in SLIMBus Errors like:
qcom,slim-ngd qcom,slim-ngd.1: Tx:MT:0x0, MC:0x60, LA:0xcf failed:-110
wcd934x-codec wcd934x-codec.1.auto: ASoC: error at soc_component_read_no_lock
on wcd934x-codec.1.auto for register: [0x00000d05] -110
qcom,slim-ngd-ctrl 171c0000.slim: Error Interrupt received 0x82000000
Reported-by: Amit Pundir <amit.pundir@linaro.org> Fixes: a61f3b4f476e ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec") Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Amit Pundir <amit.pundir@linaro.org> Link: https://lore.kernel.org/r/20220407094313.2880-1-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MCLK of the WM8731 on the AT91SAM9G20-EK board is connected to the
PCK0 output of the SoC, intended in the reference software to be supplied
using PLLB and programmed to 12MHz. As originally written for use with a
board file the audio driver was responsible for configuring the entire tree
but in the conversion to the common clock framework the registration of
the named pck0 and pllb clocks was removed so the driver has failed to
instantiate ever since.
Since the WM8731 driver has had support for managing a MCLK provided via
the common clock framework for some time we can simply drop all the clock
management code from the machine driver other than configuration of the
sysclk rate, the CODEC driver still respects that configuration from the
machine driver.
Fixes: ff78a189b0ae55f ("ARM: at91: remove old at91-specific clock driver") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220325154241.1600757-2-broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
dm_io_dec_pending() calls end_io_acct() first and will then dec md
in-flight pending count. But if a task is swapping DM table at same
time this can result in a crash due to mempool->elements being NULL:
Fix this by:
1) Establishing pointers to 'struct dm_io' members in
dm_io_dec_pending() so that they may be passed into end_io_acct()
_after_ free_io() is called.
2) Moving end_io_acct() after free_io().
Cc: stable@vger.kernel.org Signed-off-by: Jiazi Li <lijiazi@xiaomi.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Akilesh Kailash <akailash@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a rawmidi output stream is closed, it calls the drain at first,
then does trigger-off only when the drain returns -ERESTARTSYS as a
fallback. It implies that each driver should turn off the stream
properly after the drain. Meanwhile, USB-audio MIDI interface didn't
change the port->active flag after the drain. This may leave the
output work picking up the port that is closed right now, which
eventually leads to a use-after-free for the already released rawmidi
object.
This patch fixes the bug by properly clearing the port->active flag
after the output drain.
We are now able to detect extra put_net() at the moment
they happen, instead of much later in correct code paths.
u32_init_knode() / tcf_exts_init() populates the ->exts.net
pointer, but as mentioned in tcf_exts_init(),
the refcount on netns has not been elevated yet.
The refcount is taken only once tcf_exts_get_net()
is called.
So the two u32_destroy_key() calls from u32_change()
are attempting to release an invalid reference on the netns.
Before this patch, function read_rindex_entry called compute_bitstructs
before it allocated a glock for the rgrp. But if compute_bitstructs found
a problem with the rgrp, it called gfs2_consist_rgrpd, and that called
gfs2_dump_glock for rgd->rd_gl which had not yet been assigned.
read_rindex_entry
compute_bitstructs
gfs2_consist_rgrpd
gfs2_dump_glock <---------rgd->rd_gl was not set.
This patch changes read_rindex_entry so it assigns an rgrp glock before
calling compute_bitstructs so gfs2_dump_glock does not reference an
unassigned pointer. If an error is discovered, the glock must also be
put, so a new goto and label were added.
Reported-by: syzbot+c6fd14145e2f62ca0784@syzkaller.appspotmail.com Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That is happening because a dummy event is opened to capture text poke
events accross all CPUs, however the mmap logic is allocating according
to the number of user_requested_cpus.
In general, perf sometimes uses the evsel cpus to open events, and
sometimes the evlist user_requested_cpus. However, it is not necessary
to determine which case is which because the opened event file
descriptors are also in an xyarray, the size of whch can be used
to correctly allocate the size of the sample_id xyarray, because there
is one ID per file descriptor.
Note, in the affected code path, perf_evsel fd array is subsequently
used to get the file descriptor for the mmap, so it makes sense for the
xyarrays to be the same size there.
Fixes: d1a177595b3a824c ("libperf: Adopt perf_evlist__mmap()/munmap() from tools/perf") Fixes: 246eba8e9041c477 ("perf tools: Add support for PERF_RECORD_TEXT_POKE") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: stable@vger.kernel.org # 5.5+ Link: https://lore.kernel.org/r/20220413114232.26914-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stacktrace event trigger is not dumping the stacktrace to the instance
where it was enabled, but to the global "instance."
Use the private_data, pointing to the trigger file, to figure out the
corresponding trace instance, and use it in the trigger action, like
snapshot_trigger does.
Link: https://lkml.kernel.org/r/afbb0b4f18ba92c276865bc97204d438473f4ebc.1645396236.git.bristot@kernel.org Cc: stable@vger.kernel.org Fixes: ae63b31e4d0e2 ("tracing: Separate out trace events from global variables") Reviewed-by: Tom Zanussi <zanussi@kernel.org> Tested-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arthur Marsh reported we would hit the error below when building kernel
with gcc-12:
CC mm/page_alloc.o
mm/page_alloc.c: In function `mem_init_print_info':
mm/page_alloc.c:8173:27: error: comparison between two arrays [-Werror=array-compare]
8173 | if (start <= pos && pos < end && size > adj) \
|
In C++20, the comparision between arrays should be warned.
Link: https://lkml.kernel.org/r/20211125130928.32465-1-sxwjean@me.com Signed-off-by: Xiongwei Song <sxwjean@gmail.com> Reported-by: Arthur Marsh <arthur.marsh@internode.on.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Khem Raj <raj.khem@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With GCC 12, -Wstringop-overread was warning about an implicit cast from
char[6] to char[8]. However, the extra 2 bytes are always thrown away,
alignment doesn't matter, and the risk of hitting the edge of unallocated
memory has been accepted, so this prototype can just be converted to a
regular char *. Silences:
net/core/dev.c: In function ‘bpf_prog_run_generic_xdp’: net/core/dev.c:4618:21: warning: ‘ether_addr_equal_64bits’ reading 8 bytes from a region of size 6 [-Wstringop-overread]
4618 | orig_host = ether_addr_equal_64bits(eth->h_dest, > skb->dev->dev_addr);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/core/dev.c:4618:21: note: referencing argument 1 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’}
net/core/dev.c:4618:21: note: referencing argument 2 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’}
In file included from net/core/dev.c:91: include/linux/etherdevice.h:375:20: note: in a call to function ‘ether_addr_equal_64bits’
375 | static inline bool ether_addr_equal_64bits(const u8 addr1[6+2],
| ^~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/netdev/20220212090811.uuzk6d76agw2vv73@pengutronix.de Cc: Jakub Kicinski <kuba@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Khem Raj <raj.khem@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are race conditions that may lead to UAF bugs in
ax25_heartbeat_expiry(), ax25_t1timer_expiry(), ax25_t2timer_expiry(),
ax25_t3timer_expiry() and ax25_idletimer_expiry(), when we call
ax25_release() to deallocate ax25_dev.
One of the UAF bugs caused by ax25_release() is shown below:
We increase the refcount of ax25_dev in position (1) and (2), and
decrease the refcount of ax25_dev in position (3) and (4).
The ax25_dev will be freed in position (4) and be used in
ax25_t1timer_expiry().
The fail log is shown below:
==============================================================
[ 106.116942] BUG: KASAN: use-after-free in ax25_t1timer_expiry+0x1c/0x60
[ 106.116942] Read of size 8 at addr ffff88800bda9028 by task swapper/0/0
[ 106.116942] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.17.0-06123-g0905eec574
[ 106.116942] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-14
[ 106.116942] Call Trace:
...
[ 106.116942] ax25_t1timer_expiry+0x1c/0x60
[ 106.116942] call_timer_fn+0x122/0x3d0
[ 106.116942] __run_timers.part.0+0x3f6/0x520
[ 106.116942] run_timer_softirq+0x4f/0xb0
[ 106.116942] __do_softirq+0x1c2/0x651
...
This patch adds del_timer_sync() in ax25_release(), which could ensure
that all timers stop before we deallocate ax25_dev.
The previous commit 7ec02f5ac8a5 ("ax25: fix NPD bug in ax25_disconnect")
move ax25_disconnect into lock_sock() in order to prevent NPD bugs. But
there are race conditions that may lead to null pointer dereferences in
ax25_heartbeat_expiry(), ax25_t1timer_expiry(), ax25_t2timer_expiry(),
ax25_t3timer_expiry() and ax25_idletimer_expiry(), when we use
ax25_kill_by_device() to detach the ax25 device.
One of the race conditions that cause null pointer dereferences can be
shown as below:
This patch moves ax25_disconnect() before s->ax25_dev = NULL
and uses del_timer_sync() to delete timers in ax25_disconnect().
If ax25_disconnect() is called by ax25_kill_by_device() or
ax25->ax25_dev is NULL, the reason in ax25_disconnect() will be
equal to ENETUNREACH, it will wait all timers to stop before we
set null to s->ax25_dev in ax25_kill_by_device().
Fixes: 7ec02f5ac8a5 ("ax25: fix NPD bug in ax25_disconnect") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
[OP: backport to 5.10: adjust context] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ax25_disconnect() in ax25_kill_by_device() is not
protected by any locks, thus there is a race condition
between ax25_disconnect() and ax25_destroy_socket().
when ax25->sk is assigned as NULL by ax25_destroy_socket(),
a NULL pointer dereference bug will occur if site (1) or (2)
dereferences ax25->sk.
The refcount of ax25_dev increases in position (1) and (2), and
decreases in position (3) and (4). The ax25_dev will be freed
before dereference sites in ax25_send_control().
The previous commit d01ffb9eee4a ("ax25: add refcount in ax25_dev to
avoid UAF bugs") and commit feef318c855a ("ax25: fix UAF bugs of
net_device caused by rebinding operation") increase the refcounts of
ax25_dev and net_device in ax25_bind() and decrease the matching refcounts
in ax25_kill_by_device() in order to prevent UAF bugs, but there are
reference count leaks.
Firstly, we use ax25_bind() to increase the refcount of ax25_dev in
position (1) and increase the refcount of net_device in position (2).
Then, we use ax25_cb_del() invoked by ax25_destroy_socket() to delete
ax25_cb in hlist in position (3) before calling ax25_kill_by_device().
Finally, the decrements of refcounts in ax25_kill_by_device() will not
be executed, because no s->ax25_dev equals to ax25_dev in position (4).
This patch adds decrements of refcounts in ax25_release() and use
lock_sock() to do synchronization. If refcounts decrease in ax25_release(),
the decrements of refcounts in ax25_kill_by_device() will not be
executed and vice versa.
Fixes: d01ffb9eee4a ("ax25: add refcount in ax25_dev to avoid UAF bugs") Fixes: 87563a043cef ("ax25: fix reference count leaks of ax25_dev") Fixes: feef318c855a ("ax25: fix UAF bugs of net_device caused by rebinding operation") Reported-by: Thomas Osterried <thomas@osterried.de> Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
[OP: backport to 5.10: adjust dev_put_track()->dev_put()] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ax25_kill_by_device() will set s->ax25_dev = NULL and
call ax25_disconnect() to change states of ax25_cb and
sock, if we call ax25_bind() before ax25_kill_by_device().
However, if we call ax25_bind() again between the window of
ax25_kill_by_device() and ax25_dev_device_down(), the values
and states changed by ax25_kill_by_device() will be reassigned.
Finally, ax25_dev_device_down() will deallocate net_device.
If we dereference net_device in syscall functions such as
ax25_release(), ax25_sendmsg(), ax25_getsockopt(), ax25_getname()
and ax25_info_show(), a UAF bug will occur.
One of the possible race conditions is shown below:
the corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in ax25_send_control+0x43/0x210
...
Call Trace:
...
ax25_send_control+0x43/0x210
ax25_release+0x2db/0x3b0
__sock_release+0x6d/0x120
sock_close+0xf/0x20
__fput+0x11f/0x420
...
Allocated by task 1283:
...
__kasan_kmalloc+0x81/0xa0
alloc_netdev_mqs+0x5a/0x680
mkiss_open+0x6c/0x380
tty_ldisc_open+0x55/0x90
...
Freed by task 1969:
...
kfree+0xa3/0x2c0
device_release+0x54/0xe0
kobject_put+0xa5/0x120
tty_ldisc_kill+0x3e/0x80
...
In order to fix these UAF bugs caused by rebinding operation,
this patch adds dev_hold_track() into ax25_bind() and
corresponding dev_put_track() into ax25_kill_by_device().
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
[OP: backport to 5.10: adjust dev_put_track()->dev_put() and
dev_hold_track()->dev_hold()] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous commit d01ffb9eee4a ("ax25: add refcount in ax25_dev
to avoid UAF bugs") introduces refcount into ax25_dev, but there
are reference leak paths in ax25_ctl_ioctl(), ax25_fwd_ioctl(),
ax25_rt_add(), ax25_rt_del() and ax25_rt_opt().
This patch uses ax25_dev_put() and adjusts the position of
ax25_addr_ax25dev() to fix reference cout leaks of ax25_dev.
Fixes: d01ffb9eee4a ("ax25: add refcount in ax25_dev to avoid UAF bugs") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220203150811.42256-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[OP: backport to 5.10: adjust context] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we dereference ax25_dev after we call kfree(ax25_dev) in
ax25_dev_device_down(), it will lead to concurrency UAF bugs.
There are eight syscall functions suffer from UAF bugs, include
ax25_bind(), ax25_release(), ax25_connect(), ax25_ioctl(),
ax25_getname(), ax25_sendmsg(), ax25_getsockopt() and
ax25_info_show().
The root cause of UAF bugs is that kfree(ax25_dev) in
ax25_dev_device_down() is not protected by any locks.
When ax25_dev, which there are still pointers point to,
is released, the concurrency UAF bug will happen.
This patch introduces refcount into ax25_dev in order to
guarantee that there are no pointers point to it when ax25_dev
is released.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
[OP: backport to 5.10: adjusted context] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a driver raises a connection error before the connection is bound, we
can leave a cleanup_work queued that can later run and disconnect/stop a
connection that is logged in. The problem is that drivers can call
iscsi_conn_error_event for endpoints that are connected but not yet bound
when something like the network port they are using is brought down.
iscsi_cleanup_conn_work_fn will check for this and exit early, but if the
cleanup_work is stuck behind other works, it might not get run until after
userspace has done ep_disconnect. Because the endpoint is not yet bound
there was no way for ep_disconnect to flush the work.
The bug of leaving stop_conns queued was added in:
This patch fixes a bug where when using iSCSI offload we can free an
endpoint while userspace still thinks it's active. That then causes the
endpoint ID to be reused for a new connection's endpoint while userspace
still thinks the ID is for the original connection. Userspace will then end
up disconnecting a running connection's endpoint or trying to bind to
another connection's endpoint.
where we would call stop_conn without having done ep_disconnect. This early
ep_disconnect call will then free the endpoint and it's ID while userspace
still thinks the ID is valid.
Fix the early release of the ID by having the in kernel recovery code keep
a reference to the endpoint until userspace has called into the kernel to
finish cleaning up the endpoint/connection. It requires the previous commit
"scsi: iscsi: Release endpoint ID when its freed" which moved the freeing
of the ID until when the endpoint is released.
Link: https://lore.kernel.org/r/20220408001314.5014-5-michael.christie@oracle.com Fixes: 23d6fefbb3f6 ("scsi: iscsi: Fix in-kernel conn failure handling") Tested-by: Manish Rangankar <mrangankar@marvell.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we looked into FIO performance with swiotlb enabled in VM, we found
swiotlb_bounce() is always called one more time than expected for each DMA
read request.
It turns out that the bounce buffer is copied to original DMA buffer twice
after the completion of a DMA request (one is done by in
dma_direct_sync_single_for_cpu(), the other by swiotlb_tbl_unmap_single()).
But the content in bounce buffer actually doesn't change between the two
rounds of copy. So, one round of copy is redundant.
Pass DMA_ATTR_SKIP_CPU_SYNC flag to swiotlb_tbl_unmap_single() to
skip the memory copy in it.
This fix increases FIO 64KB sequential read throughput in a guest with
swiotlb=force by 5.6%.
Fixes: 55897af63091 ("dma-direct: merge swiotlb_dma_ops into the dma_direct code") Reported-by: Wang Zhaoyang1 <zhaoyang1.wang@intel.com> Reported-by: Gao Liang <liang.gao@intel.com> Signed-off-by: Chao Gao <chao.gao@intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the timer base is empty, base::next_expiry is set to base::clk +
NEXT_TIMER_MAX_DELTA and base::next_expiry_recalc is false. When no timer
is queued until jiffies reaches base::next_expiry value, the warning for
not finding any expired timer and base::next_expiry_recalc is false in
__run_timers() triggers.
To prevent triggering the warning in this valid scenario
base::timers_pending needs to be added to the warning condition.
Fixes: 31cd0e119d50 ("timers: Recalculate next timer interrupt only when necessary") Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20220405191732.7438-3-anna-maria@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e6e ("i2c: PA Semi SMBus driver") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Reviewed-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check in flush_smp_call_function_queue() for callbacks that are sent
to offline CPUs currently checks whether the queue is empty.
However, flush_smp_call_function_queue() has just deleted all the
callbacks from the queue and moved all the entries into a local list.
This checks would only be positive if some callbacks were added in the
short time after llist_del_all() was called. This does not seem to be
the intention of this check.
Change the check to look at the local list to which the entries were
moved instead of the queue from which all the callbacks were just
removed.
Fixes: 8d056c48e4862 ("CPU hotplug, smp: flush any pending IPI callbacks before CPU offline") Signed-off-by: Nadav Amit <namit@vmware.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220319072015.1495036-1-namit@vmware.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible to set up dm-integrity in such a way that the
"tag_size" parameter is less than the actual digest size. In this
situation, a part of the digest beyond tag_size is ignored.
In this case, dm-integrity would write beyond the end of the
ic->recalc_tags array and corrupt memory. The corruption happened in
integrity_recalc->integrity_sector_checksum->crypto_shash_final.
Fix this corruption by increasing the tags array so that it has enough
padding at the end to accomodate the loop in integrity_recalc() being
able to write a full digest size for the last member of the tags
array.
With newer versions of GCC, there is a panic in da850_evm_config_emac()
when booting multi_v5_defconfig in QEMU under the palmetto-bmc machine:
Unable to handle kernel NULL pointer dereference at virtual address 00000020
pgd = (ptrval)
[00000020] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.15.0 #1
Hardware name: Generic DT based system
PC is at da850_evm_config_emac+0x1c/0x120
LR is at do_one_initcall+0x50/0x1e0
The emac_pdata pointer in soc_info is NULL because davinci_soc_info only
gets populated on davinci machines but da850_evm_config_emac() is called
on all machines via device_initcall().
Move the rmii_en assignment below the machine check so that it is only
dereferenced when running on a supported SoC.
While running some testing on code that happened to allow the variable
tick_nohz_full_running to get set but with no "possible" NOHZ cores to
back up that setting, this warning triggered:
if (unlikely(tick_do_timer_cpu == TICK_DO_TIMER_NONE))
WARN_ON(tick_nohz_full_running);
The console was overwhemled with an endless stream of one WARN per tick
per core and there was no way to even see what was going on w/o using a
serial console to capture it and then trace it back to this.
Change it to WARN_ON_ONCE().
Fixes: 08ae95f4fd3b ("nohz_full: Allow the boot CPU to be nohz_full") Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211206145950.10927-3-paul.gortmaker@windriver.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CPUs on a node are offline at boot time, the number of nodes is
different when building affinity masks for present cpus and when building
affinity masks for possible cpus. This causes the following problem:
In the case that the number of vectors is less than the number of nodes
there are cases where bits of masks for present cpus are overwritten when
building masks for possible cpus.
Fix this by excluding CPUs, which are not part of the current build mask
(present/possible).
[ tglx: Massaged changelog and added comment ]
Fixes: b82592199032 ("genirq/affinity: Spread IRQs to all available NUMA nodes") Signed-off-by: Rei Yamamoto <yamamoto.rei@jp.fujitsu.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ming Lei <ming.lei@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220331003309.10891-1-yamamoto.rei@jp.fujitsu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Pre-multiplied" is the default pixel blend mode for KMS/DRM, as
documented in supported_modes of drm_plane_create_blend_mode_property():
https://cgit.freedesktop.org/drm/drm-misc/tree/drivers/gpu/drm/drm_blend.c
In this mode, both 'pixel alpha' and 'plane alpha' participate in the
calculation, as described by the pixel blend mode formula in KMS/DRM
documentation:
Considering the blend config mechanisms we have in the driver so far,
the alpha mode that better fits this blend mode is the
_PER_PIXEL_ALPHA_COMBINED_GLOBAL_GAIN, where the value for global_gain
is the plane alpha (global_alpha).
With this change, alpha property stops to be ignored. It also addresses
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1734
v2:
* keep the 8-bit value for global_alpha_value (Nicholas)
* correct the logical ordering for combined global gain (Nicholas)
* apply to dcn10 too (Nicholas)
Signed-off-by: Melissa Wen <mwen@igalia.com> Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Tested-by: Simon Ser <contact@emersion.fr> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kongweibin reported a kernel panic in ip6_forward() when input interface
has no in6 dev associated.
The following tc commands were used to reproduce this panic:
tc qdisc del dev vxlan100 root
tc qdisc add dev vxlan100 root netem corrupt 5%
CC: stable@vger.kernel.org Fixes: ccd27f05ae7b ("ipv6: fix 'disable_policy' for fwd packets") Reported-by: kongweibin <kongweibin2@huawei.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need this to be at least two bytes, so we can access
alpha2[0] and alpha2[1]. It may be three in case some
userspace used NUL-termination since it was NLA_STRING
(and we also push it out with NUL-termination).
For this specific device on Lenovo Thinkpad X12 tablet, the verbs were
dumped by qemu running a guest OS that init this codec properly.
After studying the dump, it turns out that
the same quirk used by the other Lenovo devices can be reused.
The patch was tested working against the mainline kernel.
When btrfs balance is interrupted with umount, the background balance
resumes on the next mount. There is a potential deadlock with FS freezing
here like as described in commit 26559780b953 ("btrfs: zoned: mark
relocation as writing"). Mark the process as sb_writing to avoid it.
Reviewed-by: Filipe Manana <fdmanana@suse.com> CC: stable@vger.kernel.org # 4.9+ Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ieee80211_tx_info_clear_status() helper also clears the rate counts and
the driver-private part of struct ieee80211_tx_info, so using it breaks
quite a few other things. So back out of using it, and instead define a
ath-internal helper that only clears the area between the
status_driver_data and the rates info. Combined with moving the
ath_frame_info struct to status_driver_data, this avoids clearing anything
we shouldn't be, and so we can keep the existing code for handling the rate
information.
While fixing this I also noticed that the setting of
tx_info->status.rates[tx_rateindex].count on hardware underrun errors was
always immediately overridden by the normal setting of the same fields, so
rearrange the code so that the underrun detection actually takes effect.
The new helper could be generalised to a 'memset_between()' helper, but
leave it as a driver-internal helper for now since this needs to go to
stable.
Cc: stable@vger.kernel.org Reported-by: Peter Seiderer <ps.report@gmx.net> Fixes: 037250f0a45c ("ath9k: Properly clear TX status area before reporting to mac80211") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: Peter Seiderer <ps.report@gmx.net> Tested-by: Peter Seiderer <ps.report@gmx.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220404204800.2681133-1-toke@toke.dk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_info struct before reporting TX status to mac80211. Instead,
it was manually filling in fields, which meant that fields introduced later
were left as-is.
Conveniently, mac80211 actually provides a helper to zero out the status
area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information
seems to have actually been fixing an issue that was also caused by the
area being uninitialised; but it only added clearing of a single field
instead of the whole struct. That is now redundant, though, so revert that
commit and use it as a convenient Fixes tag.
Fixes: cc591d77aba1 ("ath9k: Make sure to zero status.tx_time before reporting TX status") Reported-by: Bagas Sanjaya <bagasdotme@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Tested-by: Bagas Sanjaya <bagasdotme@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220330164409.16645-1-toke@toke.dk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the latent entropy plugin mostly doesn't derive entropy from
get_random_const() for measuring the call graph, when __latent_entropy is
applied to a constant, then it's initialized statically to output from
get_random_const(). In that case, this data is derived from a 64-bit
seed, which means a buffer of 512 bits doesn't really have that amount
of compile-time entropy.
This patch fixes that shortcoming by just buffering chunks of
/dev/urandom output and doling it out as requested.
At the same time, it's important that we don't break the use of
-frandom-seed, for people who want the runtime benefits of the latent
entropy plugin, while still having compile-time determinism. In that
case, we detect whether gcc's set_random_seed() has been called by
making a call to get_random_seed(noinit=true) in the plugin init
function, which is called after set_random_seed() is called but before
anything that calls get_random_seed(noinit=false), and seeing if it's
zero or not. If it's not zero, we're in deterministic mode, and so we
just generate numbers with a basic xorshift prng.
Note that we don't detect if -frandom-seed is being used using the
documented local_tick variable, because it's assigned via:
local_tick = (unsigned) tv.tv_sec * 1000 + tv.tv_usec / 1000;
which may well overflow and become -1 on its own, and so isn't
reliable: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=105171
[kees: The 256 byte rnd_buf size was chosen based on average (250),
median (64), and std deviation (575) bytes of used entropy for a
defconfig x86_64 build]
Fixes: 38addce8b600 ("gcc-plugins: Add latent_entropy plugin") Cc: stable@vger.kernel.org Cc: PaX Team <pageexec@freemail.hu> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20220405222815.21155-1-Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resolve nx_huge_pages to true/false when kvm.ko is loaded, leaving it as
-1 is technically undefined behavior when its value is read out by
param_get_bool(), as boolean values are supposed to be '0' or '1'.
Alternatively, KVM could define a custom getter for the param, but the
auto value doesn't depend on the vendor module in any way, and printing
"auto" would be unnecessarily unfriendly to the user.
In addition to fixing the undefined behavior, resolving the auto value
also fixes the scenario where the auto value resolves to N and no vendor
module is loaded. Previously, -1 would result in Y being printed even
though KVM would ultimately disable the mitigation.
Rename the existing MMU module init/exit helpers to clarify that they're
invoked with respect to the vendor module, and add comments to document
why KVM has two separate "module init" flows.
=========================================================================
UBSAN: invalid-load in kernel/params.c:320:33
load of value 255 is not a valid value for type '_Bool'
CPU: 6 PID: 892 Comm: tail Not tainted 5.17.0-rc3+ #799
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value.cold+0x43/0x48
param_get_bool.cold+0xf/0x14
param_attr_show+0x55/0x80
module_attr_show+0x1c/0x30
sysfs_kf_seq_show+0x93/0xc0
seq_read_iter+0x11c/0x450
new_sync_read+0x11b/0x1a0
vfs_read+0xf0/0x190
ksys_read+0x5f/0xe0
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
</TASK>
=========================================================================
Fixes: b8e8c8303ff2 ("kvm: mmu: ITLB_MULTIHIT mitigation") Cc: stable@vger.kernel.org Reported-by: Bruno Goncalves <bgoncalv@redhat.com> Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220331221359.3912754-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kmemleak_*_phys() apis do not check the address for lowmem's min
boundary, while the caller may pass an address below lowmem, which will
trigger an oops:
The callers may not quite know the actual address they pass(e.g. from
devicetree). So the kmemleak_*_phys() apis should guarantee the address
they finally use is in lowmem range, so check the address for lowmem's
min boundary.
Link: https://lkml.kernel.org/r/20220413122925.33856-1-patrick.wang.shcn@gmail.com Signed-off-by: Patrick Wang <patrick.wang.shcn@gmail.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two processes under CLONE_VM cloning, user process can be corrupted by
seeing zeroed page unexpectedly.
CPU A CPU B
do_swap_page do_swap_page
SWP_SYNCHRONOUS_IO path SWP_SYNCHRONOUS_IO path
swap_readpage valid data
swap_slot_free_notify
delete zram entry
swap_readpage zeroed(invalid) data
pte_lock
map the *zero data* to userspace
pte_unlock
pte_lock
if (!pte_same)
goto out_nomap;
pte_unlock
return and next refault will
read zeroed data
The swap_slot_free_notify is bogus for CLONE_VM case since it doesn't
increase the refcount of swap slot at copy_mm so it couldn't catch up
whether it's safe or not to discard data from backing device. In the
case, only the lock it could rely on to synchronize swap slot freeing is
page table lock. Thus, this patch gets rid of the swap_slot_free_notify
function. With this patch, CPU A will see correct data.
CPU A CPU B
do_swap_page do_swap_page
SWP_SYNCHRONOUS_IO path SWP_SYNCHRONOUS_IO path
swap_readpage original data
pte_lock
map the original data
swap_free
swap_range_free
bd_disk->fops->swap_slot_free_notify
swap_readpage read zeroed data
pte_unlock
pte_lock
if (!pte_same)
goto out_nomap;
pte_unlock
return
on next refault will see mapped data by CPU B
The concern of the patch would increase memory consumption since it
could keep wasted memory with compressed form in zram as well as
uncompressed form in address space. However, most of cases of zram uses
no readahead and do_swap_page is followed by swap_free so it will free
the compressed form from in zram quickly.
Link: https://lkml.kernel.org/r/YjTVVxIAsnKAXjTd@google.com Fixes: 0bcac06f27d7 ("mm, swap: skip swapcache for swapin of synchronous device") Reported-by: Ivan Babrou <ivan@cloudflare.com> Tested-by: Ivan Babrou <ivan@cloudflare.com> Signed-off-by: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: David Hildenbrand <david@redhat.com> Cc: <stable@vger.kernel.org> [4.14+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6aa303defb74 ("mm, vmscan: only allocate and reclaim from
zones with pages managed by the buddy allocator") only zones with free
memory are included in a built zonelist. This is problematic when e.g.
all memory of a zone has been ballooned out when zonelists are being
rebuilt.
The decision whether to rebuild the zonelists when onlining new memory
is done based on populated_zone() returning 0 for the zone the memory
will be added to. The new zone is added to the zonelists only, if it
has free memory pages (managed_zone() returns a non-zero value) after
the memory has been onlined. This implies, that onlining memory will
always free the added pages to the allocator immediately, but this is
not true in all cases: when e.g. running as a Xen guest the onlined new
memory will be added only to the ballooned memory list, it will be freed
only when the guest is being ballooned up afterwards.
Another problem with using managed_zone() for the decision whether a
zone is being added to the zonelists is, that a zone with all memory
used will in fact be removed from all zonelists in case the zonelists
happen to be rebuilt.
Use populated_zone() when building a zonelist as it has been done before
that commit.
There was a report that QubesOS (based on Xen) is hitting this problem.
Xen has switched to use the zone device functionality in kernel 5.9 and
QubesOS wants to use memory hotplugging for guests in order to be able
to start a guest with minimal memory and expand it as needed. This was
the report leading to the patch.
Link: https://lkml.kernel.org/r/20220407120637.9035-1-jgross@suse.com Fixes: 6aa303defb74 ("mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator") Signed-off-by: Juergen Gross <jgross@suse.com> Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Wei Yang <richard.weiyang@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In file included from <command-line>:0:0:
In function ‘ddr_perf_counter_enable’,
inlined from ‘ddr_perf_irq_handler’ at drivers/perf/fsl_imx8_ddr_perf.c:651:2:
././include/linux/compiler_types.h:352:38: error: call to ‘__compiletime_assert_729’ \
declared with attribute error: FIELD_PREP: mask is not constant
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
...
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Frank Li <Frank.li@nxp.com> Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-arm-kernel@lists.infradead.org Acked-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20220405151517.29753-10-bp@alien8.de Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a slip driver is detaching, the slip_close() will act to
cleanup necessary resources and sl->tty is set to NULL in
slip_close(). Meanwhile, the packet we transmit is blocked,
sl_tx_timeout() will be called. Although slip_close() and
sl_tx_timeout() use sl->lock to synchronize, we don`t judge
whether sl->tty equals to NULL in sl_tx_timeout() and the
null pointer dereference bug will happen.
The megaraid_sas driver supports single LUN for RAID devices. That is LUN
0. All other LUNs are unsupported. When a device scan on a logical target
with invalid LUN number is invoked through sysfs, that target ends up
getting removed.
Add LUN ID validation in the slave destroy function to avoid the target
deletion.
The HighPoint RocketRaid 2640 is a low-cost SAS controller based on Marvell
chip. The chip in question was already supported by the kernel, just the
PCI ID of this particular board was missing.
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
why and how:
causes failure on install on certain machines
Reviewed-by: George Shen <George.Shen@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Martin Leung <Martin.Leung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All remaining skbs should be released when myri10ge_xmit fails to
transmit a packet. Fix it within another skb_list_walk_safe.
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
aqc111_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
Found doing variant analysis. Tested it with another driver (ax88179_178a), since
I don't have a aqc111 device to test it, but the code looks very similar.
Signed-off-by: Marcin Kozlowski <marcinguy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com> Reviewed-by: Greentime Hu <greentime.hu@sifive.com> Reviewed-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
tlb_remove_huge_tlb_entry only considers PMD_SIZE and PUD_SIZE when
updating the mmu_gather structure.
Unfortunately on arm64 there are two additional huge page sizes that
need to be covered: CONT_PTE_SIZE and CONT_PMD_SIZE. Where an end-user
attempts to employ contiguous huge pages, a VM_BUG_ON can be experienced
due to the fact that the tlb structure hasn't been correctly updated by
the relevant tlb_flush_p.._range() call from tlb_remove_huge_tlb_entry.
This patch adds inequality logic to the generic implementation of
tlb_remove_huge_tlb_entry s.t. CONT_PTE_SIZE and CONT_PMD_SIZE are
effectively covered on arm64. Also, as well as ptes, pmds and puds;
p4ds are now considered too.
Reported-by: David Hildenbrand <david@redhat.com> Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/linux-mm/811c5c8e-b3a2-85d2-049c-717f17c3a03a@redhat.com/ Signed-off-by: Steve Capper <steve.capper@arm.com> Acked-by: David Hildenbrand <david@redhat.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20220330112543.863-1-steve.capper@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The alternatives code must be `noinstr` such that it does not patch itself,
as the cache invalidation is only performed after all the alternatives have
been applied.
Mark patch_alternative() as `noinstr`. Mark branch_insn_requires_update()
and get_alt_insn() with `__always_inline` since they are both only called
through patch_alternative().
Booting a kernel in QEMU TCG with KCSAN=y and ARM64_USE_LSE_ATOMICS=y caused
a boot hang:
[ 0.241121] CPU: All CPU(s) started at EL2
The alternatives code was patching the atomics in __tsan_read4() from LL/SC
atomics to LSE atomics.
The following fragment is using LL/SC atomics in the .text section:
| <__tsan_unaligned_read4+304>: ldxr x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This LL/SC atomic sequence was to be replaced with LSE atomics. However since
the alternatives code was instrumentable, __tsan_read4() was being called after
only the first instruction was replaced, which led to the following code in memory:
| <__tsan_unaligned_read4+304>: ldadd x5, x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This caused an infinite loop as the `stxr` instruction never completed successfully,
so `w7` was always 0.
Signed-off-by: Joey Gouly <joey.gouly@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20220405104733.11476-1-joey.gouly@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As per Table 130 of the wm8994 datasheet at [1], there is an off-on
delay for LDO1 and LDO2. In the wm8958 datasheet [2], I could not
find any reference to it. I could not find a wm1811 datasheet to
double-check there, but as no one has complained presumably it works
without it.
This solves the issue on Samsung Aries boards with a wm8994 where
register writes fail when the device is powered off and back-on
quickly.
This commit corrects the printing of the IPU clock error percentage if
it is between -0.1% to -0.9%. For example, if the pixel clock requested
is 27.2 MHz but only 27.0 MHz can be achieved the deviation is -0.8%.
But the fixed point math had a flaw and calculated error of 0.2%.
Before:
Clocks: IPU 270000000Hz DI 24716667Hz Needed 27200000Hz
IPU clock can give 27000000 with divider 10, error 0.2%
Want 27200000Hz IPU 270000000Hz DI 24716667Hz using IPU, 27000000Hz
After:
Clocks: IPU 270000000Hz DI 24716667Hz Needed 27200000Hz
IPU clock can give 27000000 with divider 10, error -0.8%
Want 27200000Hz IPU 270000000Hz DI 24716667Hz using IPU, 27000000Hz
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com> Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Link: https://lore.kernel.org/r/20220207151411.5009-1-mark.jonas@de.bosch.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Samsung' 840 EVO with the latest firmware (EXT0DB6Q) locks up with
the a message: "READ LOG DMA EXT failed, trying PIO" during boot.
Initially this was discovered because it caused a crash
with the sata_dwc_460ex controller on a WD MyBook Live DUO.
The reporter "Tice Rex" which has the unique opportunity that he
has two Samsung 840 EVO SSD! One with the older firmware "EXT0BB0Q"
which booted fine and didn't expose "READ LOG DMA EXT". But the
newer/latest firmware "EXT0DB6Q" caused the headaches.
BugLink: https://github.com/openwrt/openwrt/issues/9505 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
KS8851_MLL selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL,
so make KS8851_MLL also depend on PTP_1588_CLOCK_OPTIONAL since
'select' does not follow any dependency chains.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851_MLL [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && HAS_IOMEM [=y]
ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info':
micrel.c:(.text+0xb35): undefined reference to `ptp_clock_index'
ld: drivers/net/phy/micrel.o: in function `lan8814_probe':
micrel.c:(.text+0x2586): undefined reference to `ptp_clock_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The adapter request_limit is hardcoded to be INITIAL_SRP_LIMIT which is
currently an arbitrary value of 800. Increase this value to 1024 which
better matches the characteristics of the typical IBMi Initiator that
supports 32 LUNs and a queue depth of 32.
This change also has the secondary benefit of being a power of two as
required by the kfifo API. Since, Commit ab9bb6318b09 ("Partially revert
"kfifo: fix kfifo_alloc() and kfifo_init()"") the size of IU pool for each
target has been rounded down to 512 when attempting to kfifo_init() those
pools with the current request_limit size of 800.
When recovering from a pci-parity error the driver is failing to re-create
queues, causing recovery to fail. Looking deeper, it was found that the
interrupt vector count allocated on the recovery was fewer than the vectors
originally allocated. This disparity resulted in CPU map entries with stale
information. When the driver tries to re-create the queues, it attempts to
use the stale information which indicates an eq/interrupt vector that was
no longer created.
Fix by clearng the cpup map array before enabling and requesting the IRQs
in the lpfc_sli_reset_slot_s4 routine().
Link: https://lore.kernel.org/r/20220317032737.45308-4-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
tcmu_try_get_data_page() looks up pages under cmdr_lock, but it does not
take refcount properly and just returns page pointer. When
tcmu_try_get_data_page() returns, the returned page may have been freed by
tcmu_blocks_release().
We need to get_page() under cmdr_lock to avoid concurrent
tcmu_blocks_release().
When reading a packet from a host-to-guest ring buffer, there is no
memory barrier between reading the write index (to see if there is
a packet to read) and reading the contents of the packet. The Hyper-V
host uses store-release when updating the write index to ensure that
writes of the packet data are completed first. On the guest side,
the processor can reorder and read the packet data before the write
index, and sometimes get stale packet data. Getting such stale packet
data has been observed in a reproducible case in a VM on ARM64.
Fix this by using virt_load_acquire() to read the write index,
ensuring that reads of the packet data cannot be reordered
before it. Preventing such reordering is logically correct, and
with this change, getting stale data can no longer be reproduced.
As the kmalloc_array() may return null, the 'event_waiters[i].wait' would lead to null-pointer dereference.
Therefore, it is better to check the return value of kmalloc_array() to avoid this confusion.
[Why & How]
The latest HDMI SPEC has updated the VTEM packet structure,
so change the VTEM Infopacket defined in the driver side to align
with the SPEC.
Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a long time leftover from when I originally added the free space
inode, the point was to catch cases where we weren't honoring the NOCOW
flag. However there exists a race with relocation, if we allocate our
free space inode in a block group that is about to be relocated, we
could trigger the COW path before the relocation has the opportunity to
find the extents and delete the free space cache. In production where
we have auto-relocation enabled we're seeing this WARN_ON_ONCE() around
5k times in a 2 week period, so not super common but enough that it's at
the top of our metrics.
We're properly handling the error here, and with us phasing out v1 space
cache anyway just drop the WARN_ON_ONCE.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the initial introduction of (posix) fallocate back at the turn of
the century, it has been possible to use this syscall to change the
user-visible contents of files. This can happen by extending the file
size during a preallocation, or through any of the newer modes (punch,
zero range). Because the call can be used to change file contents, we
should treat it like we do any other modification to a file -- update
the mtime, and drop set[ug]id privileges/capabilities.
The VFS function file_modified() does all this for us if pass it a
locked inode, so let's make fallocate drop permissions correctly.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turns out after digging deeper into this bug, that it was being
triggered by GCC12 failing to call the bcmgenet_enable_dma()
routine. Given that a gcc12 fix has been merged [1] and the genet
driver now works properly when built with gcc12, this commit should
be reverted.
Smatch printed a warning:
arch/x86/crypto/poly1305_glue.c:198 poly1305_update_arch() error:
__memcpy() 'dctx->buf' too small (16 vs u32max)
It's caused because Smatch marks 'link_len' as untrusted since it comes
from sscanf(). Add a check to ensure that 'link_len' is not larger than
the size of the 'link_str' buffer.
Fixes: c69c1b6eaea1 ("cifs: implement CIFSParseMFSymlink()") Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Our detector found a concurrent use-after-free bug when detaching an
NCI device. The main reason for this bug is the unexpected scheduling
between the used delayed mechanism (timer and workqueue).
In short, the cleanup routine thought that the cmd_timer has already
been detached by [1] but the mod_timer can re-attach the timer [2], even
it is already released [3], resulting in UAF.
This UAF is easy to trigger, crash trace by POC is like below
To fix the UAF, this patch adds flush_workqueue() to ensure the
nci_cmd_work is finished before the following del_timer_sync.
This combination will promise the timer is actually detached.
Fixes: 6a2968aaf50c ("NFC: basic NCI protocol implementation") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The selftest "mqueue/mq_perf_tests.c" use CPU_ALLOC to allocate
CPU set. This cpu set is used further in pthread_attr_setaffinity_np
and by pthread_create in the code. But in current code, allocated
cpu set is not freed.
Fix this issue by adding CPU_FREE in the "shutdown" function which
is called in most of the error/exit path for the cleanup. There are
few error paths which exit without using shutdown. Add a common goto
error path with CPU_FREE for these cases.
Function sctp_do_peeloff() wrongly initializes daddr of the original
socket instead of the peeled off socket, which makes getpeername()
return zeroes instead of the primary address. Initialize the new socket
instead.
Fixes: d570ee490fb1 ("[SCTP]: Correctly set daddr for IPv6 sockets during peeloff") Signed-off-by: Petr Malat <oss@malat.biz> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Link: https://lore.kernel.org/r/20220409063611.673193-1-oss@malat.biz Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If iscsid is doing a stop_conn at the same time the kernel is starting
error recovery we can hit a race that allows the cleanup work to run on a
valid connection. In the race, iscsi_if_stop_conn sees the cleanup bit set,
but it calls flush_work on the clean_work before iscsi_conn_error_event has
queued it. The flush then returns before the queueing and so the
cleanup_work can run later and disconnect/stop a conn while it's in a
connected state.
attempted to fix it but only fixed the normal EH case and left the above
race for the iscsid restart case. For the normal EH case we don't hit the
race because we only signal userspace to start recovery after we have done
the queueing, so the flush will always catch the queued work or see it
completed.
For iscsid restart cases like boot, we can hit the race because iscsid will
call down to the kernel before the kernel has signaled any error, so both
code paths can be running at the same time. This adds a lock around the
setting of the cleanup bit and queueing so they happen together.
Link: https://lore.kernel.org/r/20220408001314.5014-6-michael.christie@oracle.com Fixes: 0ab710458da1 ("scsi: iscsi: Perform connection failure entirely in kernel space") Tested-by: Manish Rangankar <mrangankar@marvell.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
