net/mlx5: Reset bw_share field when changing a node's parent
When changing a node's parent, its scheduling element is destroyed and
re-created with bw_share 0. However, the node's bw_share field was not
updated accordingly.
Set the node's bw_share to 0 after re-creation to keep the software
state in sync with the firmware configuration.
Fixes: 9c7bbf4c3304 ("net/mlx5: Add support for setting parent of nodes") Signed-off-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/1752155624-24095-2-git-send-email-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 11 Jul 2025 14:07:56 +0000 (07:07 -0700)]
Merge tag 'linux-can-fixes-for-6.16-20250711' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-07-11
Sean Nyekjaer's patch targets the m_can driver and demotes the "msg
lost in rx" message to debug level to prevent flooding the kernel log
with error messages.
* tag 'linux-can-fixes-for-6.16-20250711' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: m_can_handle_lost_msg(): downgrade msg lost in rx message to debug level
====================
Hangbin Liu [Wed, 9 Jul 2025 09:12:44 +0000 (09:12 +0000)]
selftests: net: lib: fix shift count out of range
I got the following warning when writing other tests:
+ handle_test_result_pass 'bond 802.3ad' '(lacp_active off)'
+ local 'test_name=bond 802.3ad'
+ shift
+ local 'opt_str=(lacp_active off)'
+ shift
+ log_test_result 'bond 802.3ad' '(lacp_active off)' ' OK '
+ local 'test_name=bond 802.3ad'
+ shift
+ local 'opt_str=(lacp_active off)'
+ shift
+ local 'result= OK '
+ shift
+ local retmsg=
+ shift
/net/tools/testing/selftests/net/forwarding/../lib.sh: line 315: shift: shift count out of range
This happens because an extra shift is executed even after all arguments
have been consumed. Remove the last shift in log_test_result() to avoid
this warning.
When fixing IPv6 link-local address generation on GRE devices with
commit 3e6a0243ff00 ("gre: Fix again IPv6 link-local address
generation."), I accidentally broke the default IPv6 multicast route
creation on these GRE devices.
Fix that in patch 1, making the GRE specific code yet a bit closer to
the generic code used by most other network interface types.
Then extend the selftest in patch 2 to cover this case.
====================
selftests: Add IPv6 multicast route generation tests for GRE devices.
The previous patch fixes a bug that prevented the creation of the
default IPv6 multicast route (ff00::/8) for some GRE devices. Now let's
extend the GRE IPv6 selftests to cover this case.
Also, rename check_ipv6_ll_addr() to check_ipv6_device_config() and
adapt comments and script output to take into account the fact that
we're not limited to link-local address generation.
Use addrconf_add_dev() instead of ipv6_find_idev() in
addrconf_gre_config() so that we don't just get the inet6_dev, but also
install the default ff00::/8 multicast route.
Before commit 3e6a0243ff00 ("gre: Fix again IPv6 link-local address
generation."), the multicast route was created at the end of the
function by addrconf_add_mroute(). But this code path is now only taken
in one particular case (gre devices not bound to a local IP address and
in EUI64 mode). For all other cases, the function exits early and
addrconf_add_mroute() is not called anymore.
Using addrconf_add_dev() instead of ipv6_find_idev() in
addrconf_gre_config(), fixes the problem as it will create the default
multicast route for all gre devices. This also brings
addrconf_gre_config() a bit closer to the normal netdevice IPv6
configuration code (addrconf_dev_config()).
Cc: stable@vger.kernel.org Fixes: 3e6a0243ff00 ("gre: Fix again IPv6 link-local address generation.") Reported-by: Aiden Yang <ling@moedove.com> Closes: https://lore.kernel.org/netdev/CANR=AhRM7YHHXVxJ4DmrTNMeuEOY87K2mLmo9KMed1JMr20p6g@mail.gmail.com/ Reviewed-by: Gary Guo <gary@garyguo.net> Tested-by: Gary Guo <gary@garyguo.net> Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/027a923dcb550ad115e6d93ee8bb7d310378bd01.1752070620.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch series improves the reliability of the Microchip LAN88xx
PHYs, particularly in edge cases involving fixed link configurations or
forced speed modes.
Patch 1 assigns genphy_soft_reset() to the .soft_reset hook to ensure
that stale link partner advertisement (LPA) bits are properly cleared
during reconfiguration. Without this, outdated autonegotiation bits may
remain visible in some parallel detection cases.
Patch 2 restricts the 100 Mbps workaround (originally intended to handle
cable length switching) to only run when the link transitions to the
PHY_NOLINK state. This prevents repeated toggling that can confuse
autonegotiating link partners such as the Intel i350, leading to
unstable link cycles.
Both patches were tested on a LAN7850 (with integrated LAN88xx PHY)
against an Intel I350 NIC. The full test suite - autonegotiation, fixed
link, and parallel detection - passed successfully.
====================
net: phy: microchip: limit 100M workaround to link-down events on LAN88xx
Restrict the 100Mbit forced-mode workaround to link-down transitions
only, to prevent repeated link reset cycles in certain configurations.
The workaround was originally introduced to improve signal reliability
when switching cables between long and short distances. It temporarily
forces the PHY into 10 Mbps before returning to 100 Mbps.
However, when used with autonegotiating link partners (e.g., Intel i350),
executing this workaround on every link change can confuse the partner
and cause constant renegotiation loops. This results in repeated link
down/up transitions and the PHY never reaching a stable state.
Limit the workaround to only run during the PHY_NOLINK state. This ensures
it is triggered only once per link drop, avoiding disruptive toggling
while still preserving its intended effect.
Note: I am not able to reproduce the original issue that this workaround
addresses. I can only confirm that 100 Mbit mode works correctly in my
test setup. Based on code inspection, I assume the workaround aims to
reset some internal state machine or signal block by toggling speeds.
However, a PHY reset is already performed earlier in the function via
phy_init_hw(), which may achieve a similar effect. Without a reproducer,
I conservatively keep the workaround but restrict its conditions.
Fixes: e57cf3639c32 ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250709130753.3994461-3-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: microchip: Use genphy_soft_reset() to purge stale LPA bits
Enable .soft_reset for the LAN88xx PHY driver by assigning
genphy_soft_reset() to ensure that the phylib core performs a proper
soft reset during reconfiguration.
Previously, the driver left .soft_reset unimplemented, so calls to
phy_init_hw() (e.g., from lan88xx_link_change_notify()) did not fully
reset the PHY. As a result, stale contents in the Link Partner Ability
(LPA) register could persist, causing the PHY to incorrectly report
that the link partner advertised autonegotiation even when it did not.
Using genphy_soft_reset() guarantees a clean reset of the PHY and
corrects the false autoneg reporting in these scenarios.
Fixes: ccb989e4d1ef ("net: phy: microchip: Reset LAN88xx PHY to ensure clean link state on LAN7800/7850") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250709130753.3994461-2-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mingming Cao [Wed, 9 Jul 2025 15:33:32 +0000 (08:33 -0700)]
ibmvnic: Fix hardcoded NUM_RX_STATS/NUM_TX_STATS with dynamic sizeof
The previous hardcoded definitions of NUM_RX_STATS and
NUM_TX_STATS were not updated when new fields were added
to the ibmvnic_{rx,tx}_queue_stats structures. Specifically,
commit 2ee73c54a615 ("ibmvnic: Add stat for tx direct vs tx
batched") added a fourth TX stat, but NUM_TX_STATS remained 3,
leading to a mismatch.
This patch replaces the static defines with dynamic sizeof-based
calculations to ensure the stat arrays are correctly sized.
This fixes incorrect indexing and prevents incomplete stat
reporting in tools like ethtool.
Fixes: 2ee73c54a615 ("ibmvnic: Add stat for tx direct vs tx batched") Signed-off-by: Mingming Cao <mmc@linux.ibm.com> Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com> Reviewed-by: Haren Myneni <haren@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250709153332.73892-1-mmc@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kito Xu [Wed, 9 Jul 2025 03:52:51 +0000 (03:52 +0000)]
net: appletalk: Fix device refcount leak in atrtr_create()
When updating an existing route entry in atrtr_create(), the old device
reference was not being released before assigning the new device,
leading to a device refcount leak. Fix this by calling dev_put() to
release the old device reference before holding the new one.
Merge tag 'net-6.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from Bluetooth.
Current release - regressions:
- tcp: refine sk_rcvbuf increase for ooo packets
- bluetooth: fix attempting to send HCI_Disconnect to BIS handle
- rxrpc: fix over large frame size warning
- eth: bcmgenet: initialize u64 stats seq counter
Previous releases - regressions:
- tcp: correct signedness in skb remaining space calculation
- sched: abort __tc_modify_qdisc if parent class does not exist
- vsock: fix transport_{g2h,h2g} TOCTOU
- rxrpc: fix bug due to prealloc collision
- tipc: fix use-after-free in tipc_conn_close().
- bluetooth: fix not marking Broadcast Sink BIS as connected
- phy: qca808x: fix WoL issue by utilizing at8031_set_wol()
- eth: am65-cpsw-nuss: fix skb size by accounting for skb_shared_info
Previous releases - always broken:
- netlink: fix wraparounds of sk->sk_rmem_alloc.
- atm: fix infinite recursive call of clip_push().
- eth:
- stmmac: fix interrupt handling for level-triggered mode in DWC_XGMAC2
- rtsn: fix a null pointer dereference in rtsn_probe()"
* tag 'net-6.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
net/sched: sch_qfq: Fix null-deref in agg_dequeue
rxrpc: Fix oops due to non-existence of prealloc backlog struct
rxrpc: Fix bug due to prealloc collision
MAINTAINERS: remove myself as netronome maintainer
selftests/net: packetdrill: add tcp_ooo-before-and-after-accept.pkt
tcp: refine sk_rcvbuf increase for ooo packets
net/sched: Abort __tc_modify_qdisc if parent class does not exist
net: ethernet: ti: am65-cpsw-nuss: Fix skb size by accounting for skb_shared_info
net: thunderx: avoid direct MTU assignment after WRITE_ONCE()
selftests/tc-testing: Create test case for UAF scenario with DRR/NETEM/BLACKHOLE chain
atm: clip: Fix NULL pointer dereference in vcc_sendmsg()
atm: clip: Fix infinite recursive call of clip_push().
atm: clip: Fix memory leak of struct clip_vcc.
atm: clip: Fix potential null-ptr-deref in to_atmarpd().
net: phy: smsc: Fix link failure in forced mode with Auto-MDIX
net: phy: smsc: Force predictable MDI-X state on LAN87xx
net: phy: smsc: Fix Auto-MDIX configuration when disabled by strap
net: stmmac: Fix interrupt handling for level-triggered mode in DWC_XGMAC2
rxrpc: Fix over large frame size warning
net: airoha: Fix an error handling path in airoha_probe()
...
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Many patches, pretty much all of them small, that accumulated while I
was on vacation.
ARM:
- Remove the last leftovers of the ill-fated FPSIMD host state
mapping at EL2 stage-1
- Fix unexpected advertisement to the guest of unimplemented S2 base
granule sizes
- Gracefully fail initialising pKVM if the interrupt controller isn't
GICv3
- Also gracefully fail initialising pKVM if the carveout allocation
fails
- Fix the computing of the minimum MMIO range required for the host
on stage-2 fault
- Fix the generation of the GICv3 Maintenance Interrupt in nested
mode
x86:
- Reject SEV{-ES} intra-host migration if one or more vCPUs are
actively being created, so as not to create a non-SEV{-ES} vCPU in
an SEV{-ES} VM
- Use a pre-allocated, per-vCPU buffer for handling de-sparsification
of vCPU masks in Hyper-V hypercalls; fixes a "stack frame too
large" issue
- Allow out-of-range/invalid Xen event channel ports when configuring
IRQ routing, to avoid dictating a specific ioctl() ordering to
userspace
- Conditionally reschedule when setting memory attributes to avoid
soft lockups when userspace converts huge swaths of memory to/from
private
- Add back MWAIT as a required feature for the MONITOR/MWAIT selftest
- Add a missing field in struct sev_data_snp_launch_start that
resulted in the guest-visible workarounds field being filled at the
wrong offset
- Skip non-canonical address when processing Hyper-V PV TLB flushes
to avoid VM-Fail on INVVPID
- Advertise supported TDX TDVMCALLs to userspace
- Pass SetupEventNotifyInterrupt arguments to userspace
- Fix TSC frequency underflow"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: avoid underflow when scaling TSC frequency
KVM: arm64: Remove kvm_arch_vcpu_run_map_fp()
KVM: arm64: Fix handling of FEAT_GTG for unimplemented granule sizes
KVM: arm64: Don't free hyp pages with pKVM on GICv2
KVM: arm64: Fix error path in init_hyp_mode()
KVM: arm64: Adjust range correctly during host stage-2 faults
KVM: arm64: nv: Fix MI line level calculation in vgic_v3_nested_update_mi()
KVM: x86/hyper-v: Skip non-canonical addresses during PV TLB flush
KVM: SVM: Add missing member in SNP_LAUNCH_START command structure
Documentation: KVM: Fix unexpected unindent warnings
KVM: selftests: Add back the missing check of MONITOR/MWAIT availability
KVM: Allow CPU to reschedule while setting per-page memory attributes
KVM: x86/xen: Allow 'out of range' event channel ports in IRQ routing table.
KVM: x86/hyper-v: Use preallocated per-vCPU buffer for de-sparsified vCPU masks
KVM: SVM: Initialize vmsa_pa in VMCB to INVALID_PAGE if VMSA page is NULL
KVM: SVM: Reject SEV{-ES} intra host migration if vCPU creation is in-flight
KVM: TDX: Report supported optional TDVMCALLs in TDX capabilities
KVM: TDX: Exit to userspace for SetupEventNotifyInterrupt
wifi: mac80211: add the virtual monitor after reconfig complete
In reconfig we add the virtual monitor in 2 cases:
1. If we are resuming (it was deleted on suspend)
2. If it was added after an error but before the reconfig
(due to the last non-monitor interface removal).
In the second case, the removal of the non-monitor interface will succeed
but the addition of the virtual monitor will fail, so we add it in the
reconfig.
The problem is that we mislead the driver to think that this is an existing
interface that is getting re-added - while it is actually a completely new
interface from the drivers' point of view.
Some drivers act differently when a interface is re-added. For example, it
might not initialize things because they were already initialized.
Such drivers will - in this case - be left with a partialy initialized vif.
To fix it, add the virtual monitor after reconfig_complete, so the
driver will know that this is a completely new interface.
This is currently not initialized for a virtual monitor, leading to a
NULL pointer dereference when - for example - iterating over all the
keys of all the vifs.
Xiang Mei [Sat, 5 Jul 2025 21:21:43 +0000 (14:21 -0700)]
net/sched: sch_qfq: Fix null-deref in agg_dequeue
To prevent a potential crash in agg_dequeue (net/sched/sch_qfq.c)
when cl->qdisc->ops->peek(cl->qdisc) returns NULL, we check the return
value before using it, similar to the existing approach in sch_hfsc.c.
To avoid code duplication, the following changes are made:
1. Changed qdisc_warn_nonwc(include/net/pkt_sched.h) into a static
inline function.
2. Moved qdisc_peek_len from net/sched/sch_hfsc.c to
include/net/pkt_sched.h so that sch_qfq can reuse it.
3. Applied qdisc_peek_len in agg_dequeue to avoid crashing.
David Howells [Tue, 8 Jul 2025 21:15:04 +0000 (22:15 +0100)]
rxrpc: Fix oops due to non-existence of prealloc backlog struct
If an AF_RXRPC service socket is opened and bound, but calls are
preallocated, then rxrpc_alloc_incoming_call() will oops because the
rxrpc_backlog struct doesn't get allocated until the first preallocation is
made.
Fix this by returning NULL from rxrpc_alloc_incoming_call() if there is no
backlog struct. This will cause the incoming call to be aborted.
Reported-by: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com> Suggested-by: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Willy Tarreau <w@1wt.eu>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org Link: https://patch.msgid.link/20250708211506.2699012-3-dhowells@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Howells [Tue, 8 Jul 2025 21:15:03 +0000 (22:15 +0100)]
rxrpc: Fix bug due to prealloc collision
When userspace is using AF_RXRPC to provide a server, it has to preallocate
incoming calls and assign to them call IDs that will be used to thread
related recvmsg() and sendmsg() together. The preallocated call IDs will
automatically be attached to calls as they come in until the pool is empty.
To the kernel, the call IDs are just arbitrary numbers, but userspace can
use the call ID to hold a pointer to prepared structs. In any case, the
user isn't permitted to create two calls with the same call ID (call IDs
become available again when the call ends) and EBADSLT should result from
sendmsg() if an attempt is made to preallocate a call with an in-use call
ID.
However, the cleanup in the error handling will trigger both assertions in
rxrpc_cleanup_call() because the call isn't marked complete and isn't
marked as having been released.
Fix this by setting the call state in rxrpc_service_prealloc_one() and then
marking it as being released before calling the cleanup function.
Fixes: 00e907127e6f ("rxrpc: Preallocate peers, conns and calls for incoming service requests") Reported-by: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org Link: https://patch.msgid.link/20250708211506.2699012-2-dhowells@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Louis Peens [Tue, 8 Jul 2025 08:20:51 +0000 (10:20 +0200)]
MAINTAINERS: remove myself as netronome maintainer
I am moving on from Corigine to different things, for the moment
slightly removed from kernel development. Right now there is nobody I
can in good conscience recommend to take over the maintainer role, but
there are still people available for review, so put the driver state to
'Odd Fixes'.
Additionally add Simon Horman as reviewer - thanks Simon.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Victor Nogueira [Mon, 7 Jul 2025 21:08:01 +0000 (18:08 -0300)]
net/sched: Abort __tc_modify_qdisc if parent class does not exist
Lion's patch [1] revealed an ancient bug in the qdisc API.
Whenever a user creates/modifies a qdisc specifying as a parent another
qdisc, the qdisc API will, during grafting, detect that the user is
not trying to attach to a class and reject. However grafting is
performed after qdisc_create (and thus the qdiscs' init callback) is
executed. In qdiscs that eventually call qdisc_tree_reduce_backlog
during init or change (such as fq, hhf, choke, etc), an issue
arises. For example, executing the following commands:
sudo tc qdisc add dev lo root handle a: htb default 2
sudo tc qdisc add dev lo parent a: handle beef fq
Qdiscs such as fq, hhf, choke, etc unconditionally invoke
qdisc_tree_reduce_backlog() in their control path init() or change() which
then causes a failure to find the child class; however, that does not stop
the unconditional invocation of the assumed child qdisc's qlen_notify with
a null class. All these qdiscs make the assumption that class is non-null.
The solution is ensure that qdisc_leaf() which looks up the parent
class, and is invoked prior to qdisc_create(), should return failure on
not finding the class.
In this patch, we leverage qdisc_leaf to return ERR_PTRs whenever the
parentid doesn't correspond to a class, so that we can detect it
earlier on and abort before qdisc_create is called.
net: ethernet: ti: am65-cpsw-nuss: Fix skb size by accounting for skb_shared_info
While transitioning from netdev_alloc_ip_align() to build_skb(), memory
for the "skb_shared_info" member of an "skb" was not allocated. Fix this
by allocating "PAGE_SIZE" as the skb length, accounting for the packet
length, headroom and tailroom, thereby including the required memory space
for skb_shared_info.
net: thunderx: avoid direct MTU assignment after WRITE_ONCE()
The current logic in nicvf_change_mtu() writes the new MTU to
netdev->mtu using WRITE_ONCE() before verifying if the hardware
update succeeds. However on hardware update failure, it attempts
to revert to the original MTU using a direct assignment
(netdev->mtu = orig_mtu)
which violates the intended of WRITE_ONCE protection introduced in
commit 1eb2cded45b3 ("net: annotate writes on dev->mtu from
ndo_change_mtu()")
Additionally, WRITE_ONCE(netdev->mtu, new_mtu) is unnecessarily
performed even when the device is not running.
Fix this by:
Only writing netdev->mtu after successfully updating the hardware.
Skipping hardware update when the device is down, and setting MTU
directly. Remove unused variable orig_mtu.
This ensures that all writes to netdev->mtu are consistent with
WRITE_ONCE expectations and avoids unintended state corruption
on failure paths.
atm: clip: Fix infinite recursive call of clip_push().
syzbot reported the splat below. [0]
This happens if we call ioctl(ATMARP_MKIP) more than once.
During the first call, clip_mkip() sets clip_push() to vcc->push(),
and the second call copies it to clip_vcc->old_push().
Later, when the socket is close()d, vcc_destroy_socket() passes
NULL skb to clip_push(), which calls clip_vcc->old_push(),
triggering the infinite recursion.
Let's prevent the second ioctl(ATMARP_MKIP) by checking
vcc->user_back, which is allocated by the first call as clip_vcc.
Note also that we use lock_sock() to prevent racy calls.
Paolo Bonzini [Wed, 9 Jul 2025 17:45:14 +0000 (13:45 -0400)]
KVM: x86: avoid underflow when scaling TSC frequency
In function kvm_guest_time_update(), __scale_tsc() is used to calculate
a TSC *frequency* rather than a TSC value. With low-enough ratios,
a TSC value that is less than 1 would underflow to 0 and to an infinite
while loop in kvm_get_time_scale():
This can really happen only when fuzzing, since the TSC frequency
would have to be nonsensically low.
Fixes: 35181e86df97 ("KVM: x86: Add a common TSC scaling function") Reported-by: Yuntao Liu <liuyuntao12@huawei.com> Suggested-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
eventpoll: don't decrement ep refcount while still holding the ep mutex
Jann Horn points out that epoll is decrementing the ep refcount and then
doing a
mutex_unlock(&ep->mtx);
afterwards. That's very wrong, because it can lead to a use-after-free.
That pattern is actually fine for the very last reference, because the
code in question will delay the actual call to "ep_free(ep)" until after
it has unlocked the mutex.
But it's wrong for the much subtler "next to last" case when somebody
*else* may also be dropping their reference and free the ep while we're
still using the mutex.
Note that this is true even if that other user is also using the same ep
mutex: mutexes, unlike spinlocks, can not be used for object ownership,
even if they guarantee mutual exclusion.
A mutex "unlock" operation is not atomic, and as one user is still
accessing the mutex as part of unlocking it, another user can come in
and get the now released mutex and free the data structure while the
first user is still cleaning up.
See our mutex documentation in Documentation/locking/mutex-design.rst,
in particular the section [1] about semantics:
"mutex_unlock() may access the mutex structure even after it has
internally released the lock already - so it's not safe for
another context to acquire the mutex and assume that the
mutex_unlock() context is not using the structure anymore"
So if we drop our ep ref before the mutex unlock, but we weren't the
last one, we may then unlock the mutex, another user comes in, drops
_their_ reference and releases the 'ep' as it now has no users - all
while the mutex_unlock() is still accessing it.
Fix this by simply moving the ep refcount dropping to outside the mutex:
the refcount itself is atomic, and doesn't need mutex protection (that's
the whole _point_ of refcounts: unlike mutexes, they are inherently
about object lifetimes).
Reported-by: Jann Horn <jannh@google.com> Link: https://docs.kernel.org/locking/mutex-design.html#semantics Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Christian Brauner <brauner@kernel.org> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix bogus KASAN splat on EFI runtime stack
- Select JUMP_LABEL unconditionally to avoid boot failure with pKVM and
the legacy implementation of static keys
- Avoid touching GCS registers when 'arm64.nogcs' has been passed on
the command-line
- Move a 'cpumask_t' off the stack in smp_send_stop()
- Don't advertise SME-related hwcaps to userspace when ID_AA64PFR1_EL1
indicates that SME is not implemented
- Always check the VMA when handling an Overlay fault
- Avoid corrupting TCR2_EL1 during boot
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/mm: Drop wrong writes into TCR2_EL1
arm64: poe: Handle spurious Overlay faults
arm64: Filter out SME hwcaps when FEAT_SME isn't implemented
arm64: move smp_send_stop() cpu mask off stack
arm64/gcs: Don't try to access GCS registers if arm64.nogcs is enabled
arm64: Unconditionally select CONFIG_JUMP_LABEL
arm64: efi: Fix KASAN false positive for EFI runtime stack
Merge tag 'pinctrl-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Mark som pins as invalid for IRQ use in the Qualcomm driver
- Fix up the use of device properties on the MA35DX Nuvoton, apparently
something went sidewise
- Clear the GPIO debounce settings when going down for suspend in the
AMD driver. Very good for some AMD laptops that now wake up from
suspend again!
- Add the compulsory .can_sleep bool flag in the AW9523 driver, should
have been there from the beginning, now there are users finding the
bug
- Drop some bouncing email address from MAINTAINERS
* tag 'pinctrl-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aw9523: fix can_sleep flag for GPIO chip
pinctrl: amd: Clear GPIO debounce for suspend
pinctrl: nuvoton: Fix boot on ma35dx platforms
MAINTAINERS: drop bouncing Lakshmi Sowjanya D
pinctrl: qcom: msm: mark certain pins as invalid for interrupts
wifi: mac80211: Fix uninitialized variable with __free() in ieee80211_ml_epcs()
The cleanup attribute runs kfree() when the variable goes out of scope.
There is a possibility that the link_elems variable is uninitialized
if the loop ends before an assignment is made to this variable.
This leads to uninitialized variable bug.
net: phy: smsc: Fix link failure in forced mode with Auto-MDIX
Force a fixed MDI-X mode when auto-negotiation is disabled to prevent
link instability.
When forcing the link speed and duplex on a LAN9500 PHY (e.g., with
`ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto
mode, the PHY fails to establish a stable link. This occurs because the
PHY's Auto-MDIX algorithm is not designed to operate when
auto-negotiation is disabled. In this state, the PHY continuously
toggles the TX/RX signal pairs, which prevents the link partner from
synchronizing.
This patch resolves the issue by detecting when auto-negotiation is
disabled. If the MDI-X control mode is set to 'auto', the driver now
forces a specific, stable mode (ETH_TP_MDI) to prevent the pair
toggling. This choice of a fixed MDI mode mirrors the behavior the
hardware would exhibit if the AUTOMDIX_EN strap were configured for a
fixed MDI connection.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: Andre Edich <andre.edich@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: smsc: Force predictable MDI-X state on LAN87xx
Override the hardware strap configuration for MDI-X mode to ensure a
predictable initial state for the driver. The initial mode of the LAN87xx
PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no
documented way to read its latched status.
This unpredictability means the driver cannot know if the PHY has
initialized with Auto-MDIX enabled or disabled, preventing it from
providing a reliable interface to the user.
This patch introduces a `config_init` hook that forces the PHY into a
known state by explicitly enabling Auto-MDIX.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: Andre Edich <andre.edich@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: smsc: Fix Auto-MDIX configuration when disabled by strap
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: Andre Edich <andre.edich@microchip.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: stmmac: Fix interrupt handling for level-triggered mode in DWC_XGMAC2
According to the Synopsys Controller IP XGMAC-10G Ethernet MAC Databook
v3.30a (section 2.7.2), when the INTM bit in the DMA_Mode register is set
to 2, the sbd_perch_tx_intr_o[] and sbd_perch_rx_intr_o[] signals operate
in level-triggered mode. However, in this configuration, the DMA does not
assert the XGMAC_NIS status bit for Rx or Tx interrupt events.
This creates a functional regression where the condition
if (likely(intr_status & XGMAC_NIS)) in dwxgmac2_dma_interrupt() will
never evaluate to true, preventing proper interrupt handling for
level-triggered mode. The hardware specification explicitly states that
"The DMA does not assert the NIS status bit for the Rx or Tx interrupt
events" (Synopsys DWC_XGMAC2 Databook v3.30a, sec. 2.7.2).
The fix ensures correct handling of both edge and level-triggered
interrupts while maintaining backward compatibility with existing
configurations. It has been tested on the hardware device (not publicly
available), and it can properly trigger the RX and TX interrupt handling
in both the INTM=0 and INTM=2 configurations.
Fixes: d6ddfacd95c7 ("net: stmmac: Add DMA related callbacks for XGMAC2") Tested-by: EricChan <chenchuangyu@xiaomi.com> Signed-off-by: EricChan <chenchuangyu@xiaomi.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250703020449.105730-1-chenchuangyu@xiaomi.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'pwm/for-6.16-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"Two fixes for v6.16-rc6
The first patch fixes an embarrassing bug in the pwm core. I really
wonder this wasn't found earlier since it's introduction in v6.11-rc1
as it greatly disturbs driving a PWM via sysfs.
The second and last patch fixes a clock balance issue in an error path
of the Mediatek PWM driver"
* tag 'pwm/for-6.16-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: mediatek: Ensure to disable clocks in error path
pwm: Fix invalid state detection
Merge tag 'modules-6.16-rc6.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/modules/linux
Pull modules fixes from Daniel Gomez:
"This includes two fixes: one introduced in the current release cycle
and another introduced back in v6.4-rc1. Additionally, as Petr and
Luis mentioned in previous pull requests, add myself (Daniel Gomez) to
the list of modules maintainers.
The first was reported by Intel's kernel test robot, and it addresses
a crash exposed by Sebastian's commit c50d295c37f2 ("rds: Use
nested-BH locking for rds_page_remainder") by allowing relocations for
the per-CPU section even if it lacks the SHF_ALLOC flag.
Petr and Sebastian went down to the archive history (before Git) and
found the commit that broke it at [1] / [2] ("Don't relocate
non-allocated regions in modules.").
The second fix, reported and fixed by Petr (with additional cleanup),
resolves a memory leak by ensuring proper deallocation if module
loading fails.
We couldn't find a reproducer other than forcing it manually or
leveraging eBPF. So, I tested it by enabling error injection in the
codetag functions through the error path that produces the leak and
made it fail until execmem is unable to allocate more memory"
David Howells [Mon, 7 Jul 2025 10:24:33 +0000 (11:24 +0100)]
rxrpc: Fix over large frame size warning
Under some circumstances, the compiler will emit the following warning for
rxrpc_send_response():
net/rxrpc/output.c: In function 'rxrpc_send_response':
net/rxrpc/output.c:974:1: warning: the frame size of 1160 bytes is larger than 1024 bytes
This occurs because the local variables include a 16-element scatterlist
array and a 16-element bio_vec array. It's probably not actually a problem
as this function is only called by the rxrpc I/O thread function in a
kernel thread and there won't be much on the stack before it.
Fix this by overlaying the bio_vec array over the kvec array in the
rxrpc_local struct. There is one of these per I/O thread and the kvec
array is intended for pointing at bits of a packet to be transmitted,
typically a DATA or an ACK packet. As packets for a local endpoint are
only transmitted by its specific I/O thread, there can be no race, and so
overlaying this bit of memory should be no problem.
Fixes: 5800b1cf3fd8 ("rxrpc: Allow CHALLENGEs to the passed to the app for a RESPONSE") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202506240423.E942yKJP-lkp@intel.com/ Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org Link: https://patch.msgid.link/20250707102435.2381045-2-dhowells@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tomas' fix for __BITS_PER_LONG was effectively reverted by a wrong
merge. Fix it and add the related files to MAINTAINERS"
* tag 'bitmap-for-6.16-rc6' of https://github.com/norov/linux:
MAINTAINERS: bitmap: add UAPI headers
uapi: bitops: use UAPI-safe variant of BITS_PER_LONG again (2)
Daniel Gomez [Fri, 4 Jul 2025 19:39:59 +0000 (21:39 +0200)]
MAINTAINERS: update Daniel Gomez's role and email address
Update Daniel Gomez's modules reviewer role to maintainer. This is
according to the plan [1][2][3] of scaling with more reviewers for
modules (for the incoming Rust support [4]) and rotate [5] every 6
months.
module: Make sure relocations are applied to the per-CPU section
The per-CPU data section is handled differently than the other sections.
The memory allocations requires a special __percpu pointer and then the
section is copied into the view of each CPU. Therefore the SHF_ALLOC
flag is removed to ensure move_module() skips it.
Later, relocations are applied and apply_relocations() skips sections
without SHF_ALLOC because they have not been copied. This also skips the
per-CPU data section.
The missing relocations result in a NULL pointer on x86-64 and very
small values on x86-32. This results in a crash because it is not
skipped like NULL pointer would and can't be dereferenced.
Such an assignment happens during static per-CPU lock initialisation
with lockdep enabled.
Allow relocation processing for the per-CPU section even if SHF_ALLOC is
missing.
Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202506041623.e45e4f7d-lkp@intel.com Fixes: 1a6100caae425 ("Don't relocate non-allocated regions in modules.") #v2.6.1-rc3 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Petr Pavlu <petr.pavlu@suse.com> Link: https://lore.kernel.org/r/20250610163328.URcsSUC1@linutronix.de Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Message-ID: <20250610163328.URcsSUC1@linutronix.de>
Petr Pavlu [Wed, 18 Jun 2025 12:26:27 +0000 (14:26 +0200)]
module: Avoid unnecessary return value initialization in move_module()
All error conditions in move_module() set the return value by updating the
ret variable. Therefore, it is not necessary to the initialize the variable
when declaring it.
Remove the unnecessary initialization.
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Daniel Gomez <da.gomez@samsung.com> Link: https://lore.kernel.org/r/20250618122730.51324-3-petr.pavlu@suse.com Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Message-ID: <20250618122730.51324-3-petr.pavlu@suse.com>
Petr Pavlu [Wed, 18 Jun 2025 12:26:26 +0000 (14:26 +0200)]
module: Fix memory deallocation on error path in move_module()
The function move_module() uses the variable t to track how many memory
types it has allocated and consequently how many should be freed if an
error occurs.
The variable is initially set to 0 and is updated when a call to
module_memory_alloc() fails. However, move_module() can fail for other
reasons as well, in which case t remains set to 0 and no memory is freed.
Fix the problem by initializing t to MOD_MEM_NUM_TYPES. Additionally, make
the deallocation loop more robust by not relying on the mod_mem_type_t enum
having a signed integer as its underlying type.
Fixes: c7ee8aebf6c0 ("module: add stop-grap sanity check on module memcpy()") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Daniel Gomez <da.gomez@samsung.com> Link: https://lore.kernel.org/r/20250618122730.51324-2-petr.pavlu@suse.com Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Message-ID: <20250618122730.51324-2-petr.pavlu@suse.com>
Merge tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fix from Eric Biggers:
"Fix an uninitialized variable in the s390 optimized SHA-1 and SHA-2.
Note that my librarification changes also fix this by greatly
simplifying how the s390 optimized SHA code is integrated. However, we
need this separate fix for 6.16 and older versions"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
crypto: s390/sha - Fix uninitialized variable in SHA-1 and SHA-2
Merge tag 'sound-6.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are device-specific small fixes, including HD-audio, USB-audio
and ASoC Intel quirks, as well as ASoC fsl, Cirrus codec and the
legacy AD driver fixes.
All look safe and easy"
* tag 'sound-6.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Enable headset Mic on Positivo K116J
ALSA: hda/tas2781: Fix calibration data parser issue
ALSA: ad1816a: Fix potential NULL pointer deref in snd_card_ad1816a_pnp()
ASoC: cs35l56: probe() should fail if the device ID is not recognized
ALSA: hda/realtek: Add quirk for ASUS ExpertBook B9403CVAR
ASoC: Intel: sof_sdw: Add quirks for Lenovo P1 and P16
ALSA: usb-audio: Improve filtering of sample rates on Focusrite devices
ASoC: Intel: soc-acpi: arl: Correct order of cs42l43 matches
MAINTAINERS: update Qualcomm audio codec drivers list
ASoC: fsl_sai: Force a software reset when starting in consumer mode
ASoC: Intel: SND_SOC_INTEL_SOF_BOARD_HELPERS select SND_SOC_ACPI_INTEL_MATCH
ASoC: fsl_asrc: use internal measured ratio for non-ideal ratio mode
ALSA: hda/realtek - Add mute LED support for HP Victus 15-fb2xxx
ALSA: hda: Add missing NVIDIA HDA codec IDs
transport_{h2g,g2h,dgram,local} may become NULL on vsock_core_unregister().
Make sure a poorly timed `rmmod transport` won't lead to a NULL/stale
pointer dereference.
Note that these oopses are pretty unlikely to happen in the wild. Splats
were collected after sprinkling kernel with mdelay()s.
Michal Luczaj [Thu, 3 Jul 2025 15:18:20 +0000 (17:18 +0200)]
vsock: Fix IOCTL_VM_SOCKETS_GET_LOCAL_CID to check also `transport_local`
Support returning VMADDR_CID_LOCAL in case no other vsock transport is
available.
Fixes: 0e12190578d0 ("vsock: add local transport support in the vsock core") Suggested-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Michal Luczaj <mhal@rbox.co> Link: https://patch.msgid.link/20250703-vsock-transports-toctou-v4-3-98f0eb530747@rbox.co Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
allwinner: a523: Rename emac0 to gmac0
This small series aims to align the name of the first ethernet
controller found on the Allwinner A523 SoC family with the name
found in the datasheets. It renames the compatible string and
any other references from "emac0" to "gmac0".
When support of the hardware was introduced, the name chosen was
"EMAC", which followed previous generations. However the datasheets
use the name "GMAC" instead, likely because there is another "GMAC"
based on a newer DWMAC IP.
====================
tcp: Correct signedness in skb remaining space calculation
Syzkaller reported a bug [1] where sk->sk_forward_alloc can overflow.
When we send data, if an skb exists at the tail of the write queue, the
kernel will attempt to append the new data to that skb. However, the code
that checks for available space in the skb is flawed:
'''
copy = size_goal - skb->len
'''
The types of the variables involved are:
'''
copy: ssize_t (s64 on 64-bit systems)
size_goal: int
skb->len: unsigned int
'''
Due to C's type promotion rules, the signed size_goal is converted to an
unsigned int to match skb->len before the subtraction. The result is an
unsigned int.
When this unsigned int result is then assigned to the s64 copy variable,
it is zero-extended, preserving its non-negative value. Consequently, copy
is always >= 0.
Assume we are sending 2GB of data and size_goal has been adjusted to a
value smaller than skb->len. The subtraction will result in copy holding a
very large positive integer. In the subsequent logic, this large value is
used to update sk->sk_forward_alloc, which can easily cause it to overflow.
The syzkaller reproducer uses TCP_REPAIR to reliably create this
condition. However, this can also occur in real-world scenarios. The
tcp_bound_to_half_wnd() function can also reduce size_goal to a small
value. This would cause the subsequent tcp_wmem_schedule() to set
sk->sk_forward_alloc to a value close to INT_MAX. Further memory
allocation requests would then cause sk_forward_alloc to wrap around and
become negative.
uapi: bitops: use UAPI-safe variant of BITS_PER_LONG again (2)
BITS_PER_LONG does not exist in UAPI headers, so can't be used by the UAPI
__GENMASK(). Instead __BITS_PER_LONG needs to be used.
When __GENMASK() was introduced in commit 3c7a8e190bc5 ("uapi: introduce uapi-friendly macros for GENMASK"),
the code was fine. A broken revert in 1e7933a575ed ("uapi: Revert "bitops: avoid integer overflow in GENMASK(_ULL)"")
introduced the incorrect usage of BITS_PER_LONG.
That was fixed in commit 11fcf368506d ("uapi: bitops: use UAPI-safe variant of BITS_PER_LONG again").
But a broken sync of the kernel headers with the tools/ headers in
commit fc92099902fb ("tools headers: Synchronize linux/bits.h with the kernel sources")
undid the fix.
Reapply the fix and while at it also fix the tools header.
Fixes: fc92099902fb ("tools headers: Synchronize linux/bits.h with the kernel sources") Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Acked-by: Yury Norov (NVIDIA) <yury.norov@gmail.com> Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Jakub Kicinski [Tue, 8 Jul 2025 02:01:28 +0000 (19:01 -0700)]
Merge tag 'for-net-2025-07-03' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_sync: Fix not disabling advertising instance
- hci_core: Remove check of BDADDR_ANY in hci_conn_hash_lookup_big_state
- hci_sync: Fix attempting to send HCI_Disconnect to BIS handle
- hci_event: Fix not marking Broadcast Sink BIS as connected
* tag 'for-net-2025-07-03' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: hci_event: Fix not marking Broadcast Sink BIS as connected
Bluetooth: hci_sync: Fix attempting to send HCI_Disconnect to BIS handle
Bluetooth: hci_core: Remove check of BDADDR_ANY in hci_conn_hash_lookup_big_state
Bluetooth: hci_sync: Fix not disabling advertising instance
====================
Memory state around the buggy address: ffff888099305900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888099305980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff888099305a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff888099305a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888099305b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: c5fa7b3cf3cb ("tipc: introduce new TIPC server infrastructure") Reported-by: syzbot+d333febcf8f4bc5f6110@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=27169a847a70550d17be Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com> Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech> Link: https://patch.msgid.link/20250702014350.692213-1-kuniyu@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'efi-fixes-for-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Drop preprocessor macros in zboot.lds which is not preprocessed
- Fix zboot .data section size and raw size when SBAT is enabled
* tag 'efi-fixes-for-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: Fix .data section size calculations when .sbat is present
efi: Drop preprocessor directives from zboot.lds
Merge tag 'tsa_x86_bugs_for_6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU speculation fixes from Borislav Petkov:
"Add the mitigation logic for Transient Scheduler Attacks (TSA)
TSA are new aspeculative side channel attacks related to the execution
timing of instructions under specific microarchitectural conditions.
In some cases, an attacker may be able to use this timing information
to infer data from other contexts, resulting in information leakage.
Add the usual controls of the mitigation and integrate it into the
existing speculation bugs infrastructure in the kernel"
* tag 'tsa_x86_bugs_for_6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/process: Move the buffer clearing before MONITOR
x86/microcode/AMD: Add TSA microcode SHAs
KVM: SVM: Advertise TSA CPUID bits to guests
x86/bugs: Add a Transient Scheduler Attacks mitigation
x86/bugs: Rename MDS machinery to something more generic
From commit 634f1a7110b4 ("vsock: support sockmap"), `struct proto
vsock_proto`, defined in af_vsock.c, is not static anymore, since it's
used by vsock_bpf.c.
If CONFIG_BPF_SYSCALL is not defined, `make C=2` will print a warning:
$ make O=build C=2 W=1 net/vmw_vsock/
...
CC [M] net/vmw_vsock/af_vsock.o
CHECK ../net/vmw_vsock/af_vsock.c
../net/vmw_vsock/af_vsock.c:123:14: warning: symbol 'vsock_proto' was not declared. Should it be static?
Declare `vsock_proto` regardless of CONFIG_BPF_SYSCALL, since it's defined
in af_vsock.c, which is built regardless of CONFIG_BPF_SYSCALL.
Fixes: 634f1a7110b4 ("vsock: support sockmap") Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://patch.msgid.link/20250703112329.28365-1-sgarzare@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 7 Jul 2025 23:43:51 +0000 (16:43 -0700)]
Merge branch 'fix-qca808x-wol-issue'
Luo Jie says:
====================
Fix QCA808X WoL Issue
Restore WoL (Wake-on-LAN) enablement via MMD3 register 0x8012 BIT5 for
the QCA808X PHY. This change resolves the issue where WoL functionality
was not working due to its unintended removal in a previous commit.
Refactor at8031_set_wol() into a shared library to enable reuse of the
Wake-on-LAN (WoL) functionality by the AT8031, QCA807X and QCA808X PHY
drivers.
====================
Luo Jie [Fri, 4 Jul 2025 05:31:14 +0000 (13:31 +0800)]
net: phy: qcom: qca808x: Fix WoL issue by utilizing at8031_set_wol()
The previous commit unintentionally removed the code responsible for
enabling WoL via MMD3 register 0x8012 BIT5. As a result, Wake-on-LAN
(WoL) support for the QCA808X PHY is no longer functional.
The WoL (Wake-on-LAN) feature for the QCA808X PHY is enabled via MMD3
register 0x8012, BIT5. This implementation is aligned with the approach
used in at8031_set_wol().
Luo Jie [Fri, 4 Jul 2025 05:31:13 +0000 (13:31 +0800)]
net: phy: qcom: move the WoL function to shared library
Move the WoL (Wake-on-LAN) functionality to a shared library to enable
its reuse by the QCA808X PHY driver, incorporating support for WoL
functionality similar to the implementation in at8031_set_wol().
Leon Yen [Wed, 25 Jun 2025 07:37:20 +0000 (15:37 +0800)]
wifi: mt76: mt792x: Limit the concurrent STA and SoftAP to operate on the same channel
Due to the lack of NoA(Notice of Absence) mechanism in SoftAP mode, it is
inappropriate to allow concurrent SoftAP and STA to operate on the
different channels.
This patch restricts the concurrent SoftAP and STA to be setup on the same
channel only.
Henry Martin [Wed, 25 Jun 2025 12:49:01 +0000 (20:49 +0800)]
wifi: mt76: mt7925: Fix null-ptr-deref in mt7925_thermal_init()
devm_kasprintf() returns NULL on error. Currently, mt7925_thermal_init()
does not check for this case, which results in a NULL pointer
dereference.
Add NULL check after devm_kasprintf() to prevent this issue.
Fixes: 396e41a74a88 ("wifi: mt76: mt7925: support temperature sensor") Signed-off-by: Henry Martin <bsdhenryma@tencent.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://patch.msgid.link/20250625124901.1839832-1-bsdhenryma@tencent.com Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 7 Jul 2025 15:47:02 +0000 (17:47 +0200)]
wifi: mt76: fix queue assignment for deauth packets
When running in AP mode and deauthenticating a client that's in powersave
mode, the disassoc/deauth packet can get stuck in a tx queue along with
other buffered frames. This can fill up hardware queues with frames
that are only released after the WTBL slot is reused for another client.
Fix this by moving deauth packets to the ALTX queue.
Felix Fietkau [Mon, 7 Jul 2025 15:47:01 +0000 (17:47 +0200)]
wifi: mt76: add a wrapper for wcid access with validation
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Deren Wu [Sun, 25 May 2025 06:11:22 +0000 (14:11 +0800)]
wifi: mt76: mt7921: prevent decap offload config before STA initialization
The decap offload configuration should only be applied after the STA has
been successfully initialized. Attempting to configure it earlier can lead
to corruption of the MAC configuration in the chip's hardware state.
Add an early check for `msta->deflink.wcid.sta` to ensure the station peer
is properly initialized before proceeding with decapsulation offload
configuration.
Deren Wu [Sun, 25 May 2025 06:11:21 +0000 (14:11 +0800)]
wifi: mt76: mt7925: prevent NULL pointer dereference in mt7925_sta_set_decap_offload()
Add a NULL check for msta->vif before accessing its members to prevent
a kernel panic in AP mode deployment. This also fix the issue reported
in [1].
The crash occurs when this function is triggered before the station is
fully initialized. The call trace shows a page fault at
mt7925_sta_set_decap_offload() due to accessing resources when msta->vif
is NULL.
Fix this by adding an early return if msta->vif is NULL and also check
wcid.sta is ready. This ensures we only proceed with decap offload
configuration when the station's state is properly initialized.
Michael Lo [Thu, 12 Jun 2025 06:20:46 +0000 (14:20 +0800)]
wifi: mt76: mt7925: fix invalid array index in ssid assignment during hw scan
Update the destination index to use 'n_ssids', which is incremented only
when a valid SSID is present. Previously, both mt76_connac_mcu_hw_scan()
and mt7925_mcu_hw_scan() used the loop index 'i' for the destination
array, potentially leaving gaps if any source SSIDs had zero length.
Cc: stable@vger.kernel.org Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips") Signed-off-by: Michael Lo <michael.lo@mediatek.com> Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Link: https://patch.msgid.link/20250612062046.160598-1-mingyen.hsieh@mediatek.com Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ming Yen Hsieh [Thu, 12 Jun 2025 06:09:31 +0000 (14:09 +0800)]
wifi: mt76: mt7925: fix the wrong config for tx interrupt
MT_INT_TX_DONE_MCU_WM may cause tx interrupt to be mishandled
during a reset failure, leading to the reset process failing.
By using MT_INT_TX_DONE_MCU instead of MT_INT_TX_DONE_MCU_WM,
the handling of tx interrupt is improved.
wifi: mt76: Remove RCU section in mt7996_mac_sta_rc_work()
Since mt7996_mcu_add_rate_ctrl() and mt7996_mcu_set_fixed_field() can't
run in atomic context, move RCU critical section in
mt7996_mcu_add_rate_ctrl() and mt7996_mcu_set_fixed_field(). This patch
fixes a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl()
Since mt76_mcu_skb_send_msg() routine can't be executed in atomic context,
move RCU section in mt7996_mcu_add_rate_ctrl() and execute
mt76_mcu_skb_send_msg() in non-atomic context. This is a preliminary
patch to fix a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl_fixed()
Since mt7996_mcu_set_fixed_field() can't be executed in a RCU critical
section, move RCU section in mt7996_mcu_add_rate_ctrl_fixed() and run
mt7996_mcu_set_fixed_field() in non-atomic context. This is a
preliminary patch to fix a 'sleep while atomic' issue in
mt7996_mac_sta_rc_work().
wifi: mt76: Move RCU section in mt7996_mcu_set_fixed_field()
Since mt76_mcu_skb_send_msg() routine can't be executed in atomic context,
move RCU section in mt7996_mcu_set_fixed_field() and execute
mt76_mcu_skb_send_msg() in non-atomic context. This is a preliminary
patch to fix a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
wifi: mt76: Assume __mt76_connac_mcu_alloc_sta_req runs in atomic context
Rely on GFP_ATOMIC flag in __mt76_connac_mcu_alloc_sta_req since it can
run in atomic context. This is a preliminary patch to fix a 'sleep while
atomic' issue in mt7996_mac_sta_rc_work().
ALSA: hda/tas2781: Fix calibration data parser issue
We will copy calibration data from position behind to front.
We have created a variable (tmp_val) point on top of calibration data
buffer, and tmp_val[1] is max of node number in original calibration
data structure, it will be overwritten after first data copy,
so can't be used as max node number check in for loop.
So we create a new variable to save max of node number (tmp_val[1]),
used to check if max node number was reached in for loop.
And a point need to be increased to point at calibration data in node.
Data saved position also need to be increased one byte.
Fixes: 4fe238513407 ("ALSA: hda/tas2781: Move and unified the calibrated-data getting function for SPI and I2C into the tas2781_hda lib") Signed-off-by: Baojun Xu <baojun.xu@ti.com> Link: https://patch.msgid.link/20250707090513.1462-1-baojun.xu@ti.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mathy Vanhoef [Mon, 16 Jun 2025 00:46:35 +0000 (02:46 +0200)]
wifi: prevent A-MSDU attacks in mesh networks
This patch is a mitigation to prevent the A-MSDU spoofing vulnerability
for mesh networks. The initial update to the IEEE 802.11 standard, in
response to the FragAttacks, missed this case (CVE-2025-27558). It can
be considered a variant of CVE-2020-24588 but for mesh networks.
This patch tries to detect if a standard MSDU was turned into an A-MSDU
by an adversary. This is done by parsing a received A-MSDU as a standard
MSDU, calculating the length of the Mesh Control header, and seeing if
the 6 bytes after this header equal the start of an rfc1042 header. If
equal, this is a strong indication of an ongoing attack attempt.
This defense was tested with mac80211_hwsim against a mesh network that
uses an empty Mesh Address Extension field, i.e., when four addresses
are used, and when using a 12-byte Mesh Address Extension field, i.e.,
when six addresses are used. Functionality of normal MSDUs and A-MSDUs
was also tested, and confirmed working, when using both an empty and
12-byte Mesh Address Extension field.
It was also tested with mac80211_hwsim that A-MSDU attacks in non-mesh
networks keep being detected and prevented.
Note that the vulnerability being patched, and the defense being
implemented, was also discussed in the following paper and in the
following IEEE 802.11 presentation:
wifi: mac80211: reject VHT opmode for unsupported channel widths
VHT operating mode notifications are not defined for channel widths
below 20 MHz. In particular, 5 MHz and 10 MHz are not valid under the
VHT specification and must be rejected.
Without this check, malformed notifications using these widths may
reach ieee80211_chan_width_to_rx_bw(), leading to a WARN_ON due to
invalid input. This issue was reported by syzbot.
Reject these unsupported widths early in sta_link_apply_parameters()
when opmode_notif is used. The accepted set includes 20, 40, 80, 160,
and 80+80 MHz, which are valid for VHT. While 320 MHz is not defined
for VHT, it is allowed to avoid rejecting HE or EHT clients that may
still send a VHT opmode notification.
Reported-by: syzbot+ededba317ddeca8b3f08@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=ededba317ddeca8b3f08 Fixes: 751e7489c1d7 ("wifi: mac80211: expose ieee80211_chan_width_to_rx_bw() to drivers") Tested-by: syzbot+ededba317ddeca8b3f08@syzkaller.appspotmail.com Signed-off-by: Moon Hee Lee <moonhee.lee.ca@gmail.com> Link: https://patch.msgid.link/20250703193756.46622-2-moonhee.lee.ca@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wifi: mwifiex: discard erroneous disassoc frames on STA interface
When operating in concurrent STA/AP mode with host MLME enabled,
the firmware incorrectly sends disassociation frames to the STA
interface when clients disconnect from the AP interface.
This causes kernel warnings as the STA interface processes
disconnect events that don't apply to it:
Add validation in the STA receive path to verify that disassoc/deauth
frames originate from the connected AP. Frames that fail this check
are discarded early, preventing them from reaching the MLME layer and
triggering WARN_ON().
This filtering logic is similar with that used in the
ieee80211_rx_mgmt_disassoc() function in mac80211, which drops
disassoc frames that don't match the current BSSID
(!ether_addr_equal(mgmt->bssid, sdata->vif.cfg.ap_addr)), ensuring
only relevant frames are processed.
Tested on:
- 8997 with FW 16.68.1.p197
Fixes: 36995892c271 ("wifi: mwifiex: add host mlme for client mode") Cc: stable@vger.kernel.org Signed-off-by: Vitor Soares <vitor.soares@toradex.com> Reviewed-by: Jeff Chen <jeff.chen_1@nxp.con> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Link: https://patch.msgid.link/20250701142643.658990-1-ivitro@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / thirdparty / linux.git / log
