We set IWL_STA_UCODE_INPROGRESS flag when we add a station
and clear it when we send the LQ command for it. But the LQ
command is sent only when the association succeeds.
If the association doesn't succeed, we would leave this flag
set and that wouldn't indicate the station entry as vacant.
This probably fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1065663
Some APs reject STA association request if a listen interval value exceeds
a threshold of 10. Thus, for example, Cisco APs may deny STA associations
returning status code 12 (Association denied due to reason outside the scope
of 802.11 standard) in the association response frame.
Fixing the issue by setting the default IWL_CONN_MAX_LISTEN_INTERVAL value
from 70 to 10.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com> Reviewed-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.
Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.
Reported-by: Marco André Dinis <marcoandredinis@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We check tid->sched without a lock taken on ath_tx_aggr_sleep(). That
is race condition which can result of doing list_del(&tid->list) twice
(second time with poisoned list node) and cause crash like shown below:
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Avoid leaking data by sending uninitialized memory and setting an
invalid (non-zero) fragment number (the sequence number is ignored
anyway) by setting the seq_ctrl field to zero.
Fixes: 3f52b7e328c5 ("mac80211: mesh power save basics") Fixes: ce662b44ce22 ("mac80211: send (QoS) Null if no buffered frames") Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a VHT network uses 20 or 40 MHz as per the HT operation
information, the channel center frequency segment 0 field in
the VHT operation information is reserved, so ignore it.
This fixes association with such networks when the AP puts 0
into the field, previously we'd disconnect due to an invalid
channel with the message
wlan0: AP VHT information is invalid, disable VHT
Fixes: f2d9d270c15ae ("mac80211: support VHT association") Reported-by: Tim Nelson <tim.l.nelson@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The MLME code in mac80211 must track whether or not the AP changed
bandwidth, but if there's no change while tracking it shouldn't do
anything, otherwise regulatory updates can make it impossible to
connect to certain APs if the regulatory database doesn't match the
information from the AP. See the precise scenario described in the
code.
This still leaves some possible problems with CSA or if the AP
actually changed bandwidth, but those cases are less common and
won't completely prevent using it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=70881
There is a race between the TX path and the STA wakeup: while
a station is sleeping, mac80211 buffers frames until it wakes
up, then the frames are transmitted. However, the RX and TX
path are concurrent, so the packet indicating wakeup can be
processed while a packet is being transmitted.
This can lead to a situation where the buffered frames list
is emptied on the one side, while a frame is being added on
the other side, as the station is still seen as sleeping in
the TX path.
As a result, the newly added frame will not be send anytime
soon. It might be sent much later (and out of order) when the
station goes to sleep and wakes up the next time.
Additionally, it can lead to the crash below.
Fix all this by synchronising both paths with a new lock.
Both path are not fastpath since they handle PS situations.
In a later patch we'll remove the extra skb queue locks to
reduce locking overhead.
Improves reliability of wifi connections with WPA, since authentication
frames are prioritized over normal traffic and also typically exempt
from aggregation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
This patch is a modification of the patch originally proposed by
Xiaotian Feng <xtfeng@gmail.com>: https://lkml.org/lkml/2012/11/5/413
This new version disables DMA channel interrupts and ensures that the
tasklet wil not be scheduled again before calling tasklet_kill().
Unfortunately the updated patch was not released at that time due to
planned rework of Tsi721 mport driver to use threaded interrupts (which
has yet to happen). Recently the issue was reported again:
https://lkml.org/lkml/2014/2/19/762.
Description from the original Xiaotian's patch:
"Some drivers use tasklet_disable in device remove/release process,
tasklet_disable will inc tasklet->count and return. If the tasklet is
not handled yet under some softirq pressure, the tasklet will be
placed on the tasklet_vec, never have a chance to be excuted. This
might lead to a heavy loaded ksoftirqd, wakeup with pending_softirq,
but tasklet is disabled. tasklet_kill should be used in this case."
This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Xiaotian Feng <xtfeng@gmail.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mike Galbraith <bitbucket@online.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
dequeue_entity() is called when p->on_rq and sets se->on_rq = 0
which appears to guarentee that the !se->on_rq condition is met.
If the task has done set_current_state(TASK_INTERRUPTIBLE) without
schedule() the second condition will be met and vruntime will be
incorrectly adjusted twice.
In certain cases this can result in the task's vruntime never increasing
past the vruntime of other tasks on the CFS' run queue, starving them of
CPU time.
This patch changes switched_from_fair() to use !p->on_rq instead of
!se->on_rq.
I'm able to cause a task with a priority of 120 to starve all other
tasks with the same priority on an ARM platform running 3.2.51-rt72
PREEMPT RT by writing one character at time to a serial tty (16550 UART)
in a tight loop. I'm also able to verify making this change corrects the
problem on that platform and kernel version.
Commit 0eef615665ed ("memcg: fix css reference leak and endless loop in
mem_cgroup_iter") got the interaction with the commit a few before it d8ad30559715 ("mm/memcg: iteration skip memcgs not yet fully
initialized") slightly wrong, and we didn't notice at the time.
It's elusive, and harder to get than the original, but for a couple of
days before rc1, I several times saw a endless loop similar to that
supposedly being fixed.
This time it was a tighter loop in __mem_cgroup_iter_next(): because we
can get here when our root has already been offlined, and the ordering
of conditions was such that we then just cycled around forever.
Fixes: 0eef615665ed ("memcg: fix css reference leak and endless loop in mem_cgroup_iter"). Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Greg Thelen <gthelen@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Global quota files are accessed from different nodes. Thus we cannot
cache offset of quota structure in the quota file after we drop our node
reference count to it because after that moment quota structure may be
freed and reallocated elsewhere by a different node resulting in
corruption of quota file.
Fix the problem by clearing dq_off when we are releasing dquot structure.
We also remove the DB_READ_B handling because it is useless -
DQ_ACTIVE_B is set iff DQ_READ_B is set.
Signed-off-by: Jan Kara <jack@suse.cz> Cc: Goldwyn Rodrigues <rgoldwyn@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Reviewed-by: Mark Fasheh <mfasheh@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
because munlock_vma_pages_range() thinks it's unexpectedly in the middle
of a THP page. This can be reproduced with default config since 3.11
kernels. A reproducer can be found in the kernel's selftest directory
for networking by running ./psock_tpacket.
The problem is that an order=2 compound page (allocated by
alloc_one_pg_vec_page() is part of the munlocked VM_MIXEDMAP vma (mapped
by packet_mmap()) and mistaken for a THP page and assumed to be order=9.
The checks for THP in munlock came with commit ff6a6da60b89 ("mm:
accelerate munlock() treatment of THP pages"), i.e. since 3.9, but did
not trigger a bug. It just makes munlock_vma_pages_range() skip such
compound pages until the next 512-pages-aligned page, when it encounters
a head page. This is however not a problem for vma's where mlocking has
no effect anyway, but it can distort the accounting.
Since commit 7225522bb429 ("mm: munlock: batch non-THP page isolation
and munlock+putback using pagevec") this can trigger a VM_BUG_ON in
PageTransHuge() check.
This patch fixes the issue by adding VM_MIXEDMAP flag to VM_SPECIAL, a
list of flags that make vma's non-mlockable and non-mergeable. The
reasoning is that VM_MIXEDMAP vma's are similar to VM_PFNMAP, which is
already on the VM_SPECIAL list, and both are intended for non-LRU pages
where mlocking makes no sense anyway. Related Lkml discussion can be
found in [2].
Jan Stancek reports manual page migration encountering allocation
failures after some pages when there is still plenty of memory free, and
bisected the problem down to commit 81c0a2bb515f ("mm: page_alloc: fair
zone allocator policy").
The problem is that GFP_THISNODE obeys the zone fairness allocation
batches on one hand, but doesn't reset them and wake kswapd on the other
hand. After a few of those allocations, the batches are exhausted and
the allocations fail.
Fixing this means either having GFP_THISNODE wake up kswapd, or
GFP_THISNODE not participating in zone fairness at all. The latter
seems safer as an acute bugfix, we can clean up later.
Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Sometimes the cleanup after memcg hierarchy testing gets stuck in
mem_cgroup_reparent_charges(), unable to bring non-kmem usage down to 0.
There may turn out to be several causes, but a major cause is this: the
workitem to offline parent can get run before workitem to offline child;
parent's mem_cgroup_reparent_charges() circles around waiting for the
child's pages to be reparented to its lrus, but it's holding
cgroup_mutex which prevents the child from reaching its
mem_cgroup_reparent_charges().
Further testing showed that an ordered workqueue for cgroup_destroy_wq
is not always good enough: percpu_ref_kill_and_confirm's call_rcu_sched
stage on the way can mess up the order before reaching the workqueue.
Instead, when offlining a memcg, call mem_cgroup_reparent_charges() on
all its children (and grandchildren, in the correct order) to have their
charges reparented first.
Fixes: e5fca243abae ("cgroup: use a dedicated workqueue for cgroup destruction") Signed-off-by: Filipe Brandenburger <filbranden@google.com> Signed-off-by: Hugh Dickins <hughd@google.com> Reviewed-by: Tejun Heo <tj@kernel.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> [v3.10+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Halve mss table size to make blind cookie guessing more difficult.
This is sad since the tables were already small, but there
is little alternative except perhaps adding more precise mss information
in the tcp timestamp. Timestamps are unfortunately not ubiquitous.
Guessing all possible cookie values still has 8-in 2**32 chance.
Reported-by: Jakob Lell <jakob@jakoblell.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
We currently accept cookies that were created less than 4 minutes ago
(ie, cookies with counter delta 0-3). Combined with the 8 mss table
values, this yields 32 possible values (out of 2**32) that will be valid.
Reducing the lifetime to < 2 minutes halves the guessing chance while
still providing a large enough period.
While at it, get rid of jiffies value -- they overflow too quickly on
32 bit platforms.
getnstimeofday is used to create a counter that increments every 64s.
perf shows getnstimeofday cost is negible compared to sha_transform;
normal tcp initial sequence number generation uses getnstimeofday, too.
Reported-by: Jakob Lell <jakob@jakoblell.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In ipcomp_compress(), sortirq is enabled too early, allowing the
per-cpu scratch buffer to be rewritten by ipcomp_decompress()
(called on the same CPU in softirq context) between populating
the buffer and copying the compressed data to the skb.
v2: as pointed out by Steffen Klassert, if we also move the
local_bh_disable() before reading the per-cpu pointers, we can
get rid of get_cpu()/put_cpu().
v3: removed ipcomp_decompress part (as explained by Herbert Xu,
it cannot be called from process context), get rid of cpu
variable (thanks to Eric Dumazet)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Recent changes to retry on ESTALE in linkat
(commit 442e31ca5a49e398351b2954b51f578353fdf210)
introduced a mountpoint reference leak and a small memory
leak in case a filesystem link operation returns ESTALE
which is pretty normal for distributed filesystems like
lustre, nfs and so on.
Free old_path in such a case.
[AV: there was another missing path_put() nearby - on the previous
goto retry]
[js: the second path_put is not in 3.12 yet, hunk removed]
The receiver MUST use the HMAC algorithm indicated in
the HMAC Identifier field. If this algorithm was not
specified by the receiver in the HMAC-ALGO parameter in
the INIT or INIT-ACK chunk during association setup, the
AUTH chunk and all the chunks after it MUST be discarded
and an ERROR chunk SHOULD be sent with the error cause
defined in Section 4.1. [...] If no endpoint pair shared
key has been configured for that Shared Key Identifier,
all authenticated chunks MUST be silently discarded. [...]
When an endpoint requires COOKIE-ECHO chunks to be
authenticated, some special procedures have to be followed
because the reception of a COOKIE-ECHO chunk might result
in the creation of an SCTP association. If a packet arrives
containing an AUTH chunk as a first chunk, a COOKIE-ECHO
chunk as the second chunk, and possibly more chunks after
them, and the receiver does not have an STCB for that
packet, then authentication is based on the contents of
the COOKIE-ECHO chunk. In this situation, the receiver MUST
authenticate the chunks in the packet by using the RANDOM
parameters, CHUNKS parameters and HMAC_ALGO parameters
obtained from the COOKIE-ECHO chunk, and possibly a local
shared secret as inputs to the authentication procedure
specified in Section 6.3. If authentication fails, then
the packet is discarded. If the authentication is successful,
the COOKIE-ECHO and all the chunks after the COOKIE-ECHO
MUST be processed. If the receiver has an STCB, it MUST
process the AUTH chunk as described above using the STCB
from the existing association to authenticate the
COOKIE-ECHO chunk and all the chunks after it. [...]
Commit bbd0d59809f9 introduced the possibility to receive
and verification of AUTH chunk, including the edge case for
authenticated COOKIE-ECHO. On reception of COOKIE-ECHO,
the function sctp_sf_do_5_1D_ce() handles processing,
unpacks and creates a new association if it passed sanity
checks and also tests for authentication chunks being
present. After a new association has been processed, it
invokes sctp_process_init() on the new association and
walks through the parameter list it received from the INIT
chunk. It checks SCTP_PARAM_RANDOM, SCTP_PARAM_HMAC_ALGO
and SCTP_PARAM_CHUNKS, and copies them into asoc->peer
meta data (peer_random, peer_hmacs, peer_chunks) in case
sysctl -w net.sctp.auth_enable=1 is set. If in INIT's
SCTP_PARAM_SUPPORTED_EXT parameter SCTP_CID_AUTH is set,
peer_random != NULL and peer_hmacs != NULL the peer is to be
assumed asoc->peer.auth_capable=1, in any other case
asoc->peer.auth_capable=0.
Now, if in sctp_sf_do_5_1D_ce() chunk->auth_chunk is
available, we set up a fake auth chunk and pass that on to
sctp_sf_authenticate(), which at latest in
sctp_auth_calculate_hmac() reliably dereferences a NULL pointer
at position 0..0008 when setting up the crypto key in
crypto_hash_setkey() by using asoc->asoc_shared_key that is
NULL as condition key_id == asoc->active_key_id is true if
the AUTH chunk was injected correctly from remote. This
happens no matter what net.sctp.auth_enable sysctl says.
The fix is to check for net->sctp.auth_enable and for
asoc->peer.auth_capable before doing any operations like
sctp_sf_authenticate() as no key is activated in
sctp_auth_asoc_init_active_key() for each case.
Now as RFC4895 section 6.3 states that if the used HMAC-ALGO
passed from the INIT chunk was not used in the AUTH chunk, we
SHOULD send an error; however in this case it would be better
to just silently discard such a maliciously prepared handshake
as we didn't even receive a parameter at all. Also, as our
endpoint has no shared key configured, section 6.3 says that
MUST silently discard, which we are doing from now onwards.
Before calling sctp_sf_pdiscard(), we need not only to free
the association, but also the chunk->auth_chunk skb, as
commit bbd0d59809f9 created a skb clone in that case.
I have tested this locally by using netfilter's nfqueue and
re-injecting packets into the local stack after maliciously
modifying the INIT chunk (removing RANDOM; HMAC-ALGO param)
and the SCTP packet containing the COOKIE_ECHO (injecting
AUTH chunk before COOKIE_ECHO). Fixed with this patch applied.
Fixes: bbd0d59809f9 ("[SCTP]: Implement the receive and verification of AUTH chunk") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <yasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
when ip_tunnel process multicast packets, it may check if the packet is looped
back packet though 'rt_is_output_route(skb_rtable(skb))' in ip_tunnel_rcv(),
but before that , skb->_skb_refdst has been dropped in iptunnel_pull_header(),
so which leads to a panic.
fix the bug: https://bugzilla.kernel.org/show_bug.cgi?id=70681
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When a target is specified like IPPROTO_ICMPV6 ipv6_find_hdr()
returns -ENOENT when it's found, not the header as expected.
A part of IPVS is broken and possible also nft_exthdr_eval().
When target is -1 which it is most cases, it works.
This patch exits the do while loop if the specific header is found
so the nexthdr could be returned as expected.
Reported-by: Art -kwaak- van Breemen <ard@telegraafnet.nl> Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
CC:Ansis Atteka <aatteka@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: Edward Cree <ecree@solarflare.com> Acked-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently we generate a new fragmentation id on UFO segmentation. It
is pretty hairy to identify the correct net namespace and dst there.
Especially tunnels use IFF_XMIT_DST_RELEASE and thus have no skb_dst
available at all.
This causes unreliable or very predictable ipv6 fragmentation id
generation while segmentation.
Luckily we already have pregenerated the ip6_frag_id in
ip6_ufo_append_data and can use it here.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If the neigh table's entries is less than gc_thresh1, the function
will return directly, and the reachabletime will not be recompute,
so the reachabletime can be guessed.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Even though only the outer vlan tag can be HW accelerated in the transmission
path, in the TUN/TAP driver vlan_features mirrors hw_features, which happens
to have the NETIF_F_HW_VLAN_?TAG_TX flags set. Because of this, during packet
tranmisssion through a stacked vlan device dev_hard_start_xmit, (incorrectly)
assuming that the vlan device supports hardware vlan acceleration, does not
add the vlan header to the skb payload and the inner vlan tags are lost
(vlan_tci contains the outer vlan tag when userspace reads the packet from
the tap device).
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Even if we create a stacked vlan interface such as veth0.10.20, it sends
single tagged frames (tagged with only vid 10).
Because vlan_features of a veth interface has the
NETIF_F_HW_VLAN_[CTAG/STAG]_TX bits, veth0.10 also has that feature, so
dev_hard_start_xmit(veth0.10) doesn't call __vlan_put_tag() and
vlan_dev_hard_start_xmit(veth0.10) overwrites vlan_tci.
This prevents us from using a combination of 802.1ad and 802.1Q
in containers, etc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently, the ebitmap_node structure has a fixed size of 32 bytes. On
a 32-bit system, the overhead is 8 bytes, leaving 24 bytes for being
used as bitmaps. The overhead ratio is 1/4.
On a 64-bit system, the overhead is 16 bytes. Therefore, only 16 bytes
are left for bitmap purpose and the overhead ratio is 1/2. With a
3.8.2 kernel, a boot-up operation will cause the ebitmap_get_bit()
function to be called about 9 million times. The average number of
ebitmap_node traversal is about 3.7.
This patch increases the size of the ebitmap_node structure to 64
bytes for 64-bit system to keep the overhead ratio at 1/4. This may
also improve performance a little bit by making node to node traversal
less frequent (< 2) as more bits are available in each node.
Signed-off-by: Waiman Long <Waiman.Long@hp.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
While running the high_systime workload of the AIM7 benchmark on
a 2-socket 12-core Westmere x86-64 machine running 3.10-rc4 kernel
(with HT on), it was found that a pretty sizable amount of time was
spent in the SELinux code. Below was the perf trace of the "perf
record -a -s" of a test run at 1500 users:
5.04% ls [kernel.kallsyms] [k] ebitmap_get_bit
1.96% ls [kernel.kallsyms] [k] mls_level_isvalid
1.95% ls [kernel.kallsyms] [k] find_next_bit
The ebitmap_get_bit() was the hottest function in the perf-report
output. Both the ebitmap_get_bit() and find_next_bit() functions
were, in fact, called by mls_level_isvalid(). As a result, the
mls_level_isvalid() call consumed 8.95% of the total CPU time of
all the 24 virtual CPUs which is quite a lot. The majority of the
mls_level_isvalid() function invocations come from the socket creation
system call.
Looking at the mls_level_isvalid() function, it is checking to see
if all the bits set in one of the ebitmap structure are also set in
another one as well as the highest set bit is no bigger than the one
specified by the given policydb data structure. It is doing it in
a bit-by-bit manner. So if the ebitmap structure has many bits set,
the iteration loop will be done many times.
The current code can be rewritten to use a similar algorithm as the
ebitmap_contains() function with an additional check for the
highest set bit. The ebitmap_contains() function was extended to
cover an optional additional check for the highest set bit, and the
mls_level_isvalid() function was modified to call ebitmap_contains().
With that change, the perf trace showed that the used CPU time drop
down to just 0.08% (ebitmap_contains + mls_level_isvalid) of the
total which is about 100X less than before.
0.07% ls [kernel.kallsyms] [k] ebitmap_contains
0.05% ls [kernel.kallsyms] [k] ebitmap_get_bit
0.01% ls [kernel.kallsyms] [k] mls_level_isvalid
0.01% ls [kernel.kallsyms] [k] find_next_bit
The remaining ebitmap_get_bit() and find_next_bit() functions calls
are made by other kernel routines as the new mls_level_isvalid()
function will not call them anymore.
This patch also improves the high_systime AIM7 benchmark result,
though the improvement is not as impressive as is suggested by the
reduction in CPU time spent in the ebitmap functions. The table below
shows the performance change on the 2-socket x86-64 system (with HT
on) mentioned above.
Signed-off-by: Waiman Long <Waiman.Long@hp.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It has been reported on very large machines that show_mem is taking almost
5 minutes to display information. This is a serious problem if there is
an OOM storm. The bulk of the cost is in show_mem doing a very expensive
PFN walk to give us the following information
Total RAM: Also available as totalram_pages
Highmem pages: Also available as totalhigh_pages
Reserved pages: Can be inferred from the zone structure
Shared pages: PFN walk required
Unshared pages: PFN walk required
Quick pages: Per-cpu walk required
Only the shared/unshared pages requires a full PFN walk but that
information is useless. It is also inaccurate as page pins of unshared
pages would be accounted for as shared. Even if the information was
accurate, I'm struggling to think how the shared/unshared information
could be useful for debugging OOM conditions. Maybe it was useful before
rmap existed when reclaiming shared pages was costly but it is less
relevant today.
The PFN walk could be optimised a bit but why bother as the information is
useless. This patch deletes the PFN walker and infers the total RAM,
highmem and reserved pages count from struct zone. It omits the
shared/unshared page usage on the grounds that it is useless. It also
corrects the reporting of HighMem as HighMem/MovableOnly as ZONE_MOVABLE
has similar problems to HighMem with respect to lowmem/highmem exhaustion.
The EPOLL_CTL_DEL path of epoll contains a classic, ab-ba deadlock.
That is, epoll_ctl(a, EPOLL_CTL_DEL, b, x), will deadlock with
epoll_ctl(b, EPOLL_CTL_DEL, a, x). The deadlock was introduced with
commmit 67347fe4e632 ("epoll: do not take global 'epmutex' for simple
topologies").
The acquistion of the ep->mtx for the destination 'ep' was added such
that a concurrent EPOLL_CTL_ADD operation would see the correct state of
the ep (Specifically, the check for '!list_empty(&f.file->f_ep_links')
However, by simply not acquiring the lock, we do not serialize behind
the ep->mtx from the add path, and thus may perform a full path check
when if we had waited a little longer it may not have been necessary.
However, this is a transient state, and performing the full loop
checking in this case is not harmful.
The important point is that we wouldn't miss doing the full loop
checking when required, since EPOLL_CTL_ADD always locks any 'ep's that
its operating upon. The reason we don't need to do lock ordering in the
add path, is that we are already are holding the global 'epmutex'
whenever we do the double lock. Further, the original posting of this
patch, which was tested for the intended performance gains, did not
perform this additional locking.
Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: Nathan Zimmer <nzimmer@sgi.com> Cc: Eric Wong <normalperson@yhbt.net> Cc: Nelson Elhage <nelhage@nelhage.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When calling EPOLL_CTL_ADD for an epoll file descriptor that is attached
directly to a wakeup source, we do not need to take the global 'epmutex',
unless the epoll file descriptor is nested. The purpose of taking the
'epmutex' on add is to prevent complex topologies such as loops and deep
wakeup paths from forming in parallel through multiple EPOLL_CTL_ADD
operations. However, for the simple case of an epoll file descriptor
attached directly to a wakeup source (with no nesting), we do not need to
hold the 'epmutex'.
This patch along with 'epoll: optimize EPOLL_CTL_DEL using rcu' improves
scalability on larger systems. Quoting Nathan Zimmer's mail on SPECjbb
performance:
"On the 16 socket run the performance went from 35k jOPS to 125k jOPS. In
addition the benchmark when from scaling well on 10 sockets to scaling
well on just over 40 sockets.
...
Currently the benchmark stops scaling at around 40-44 sockets but it seems like
I found a second unrelated bottleneck."
[akpm@linux-foundation.org: use `bool' for boolean variables, remove unneeded/undesirable cast of void*, add missed ep_scan_ready_list() kerneldoc] Signed-off-by: Jason Baron <jbaron@akamai.com> Tested-by: Nathan Zimmer <nzimmer@sgi.com> Cc: Eric Wong <normalperson@yhbt.net> Cc: Nelson Elhage <nelhage@nelhage.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Nathan Zimmer found that once we get over 10+ cpus, the scalability of
SPECjbb falls over due to the contention on the global 'epmutex', which is
taken in on EPOLL_CTL_ADD and EPOLL_CTL_DEL operations.
Patch #1 removes the 'epmutex' lock completely from the EPOLL_CTL_DEL path
by using rcu to guard against any concurrent traversals.
Patch #2 remove the 'epmutex' lock from EPOLL_CTL_ADD operations for
simple topologies. IE when adding a link from an epoll file descriptor to
a wakeup source, where the epoll file descriptor is not nested.
This patch (of 2):
Optimize EPOLL_CTL_DEL such that it does not require the 'epmutex' by
converting the file->f_ep_links list into an rcu one. In this way, we can
traverse the epoll network on the add path in parallel with deletes.
Since deletes can't create loops or worse wakeup paths, this is safe.
This patch in combination with the patch "epoll: Do not take global 'epmutex'
for simple topologies", shows a dramatic performance improvement in
scalability for SPECjbb.
Signed-off-by: Jason Baron <jbaron@akamai.com> Tested-by: Nathan Zimmer <nzimmer@sgi.com> Cc: Eric Wong <normalperson@yhbt.net> Cc: Nelson Elhage <nelhage@nelhage.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> CC: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When we turn off FRAME_POINTERs, the very first instruction in
that function causes a BUG. The problem is that we print IP in
the BUG report using %pB (from printk_address). And %pB
decrements the pointer by one to fix printing addresses of
functions with tail calls.
This was added in commit 71f9e59800e5ad4 ("x86, dumpstack: Use
%pB format specifier for stack trace") to fix the call stack
printouts.
To fix that, we use %pS only for stack addresses printouts (via
newly added printk_stack_address) and %pB for regs->ip (via
printk_address). I.e. we revert to the old behaviour for all
except call stacks. And since from all those reliable is 1, we
remove that parameter from printk_address.
All calls to xs_close are protected by XPRT_LOCKED as are most
activations of the workqueue which runs xs_tcp_setup_socket.
The exception is xs_tcp_schedule_linger_timeout.
So presumably the timeout queued by the later fires exactly when some
other code runs xs_close().
To protect against this we can move the cancel_delayed_work_sync()
call from xs_destory() to xs_close().
As xs_close is never called from the worker scheduled on
->connect_worker, this can never deadlock.
Signed-off-by: NeilBrown <neilb@suse.de>
[Trond: Make it safe to call cancel_delayed_work_sync() on AF_LOCAL sockets] Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In 76854c7e8f3f4172fef091e78d88b3b751463ac6 ("sched: Use
rt.nr_cpus_allowed to recover select_task_rq() cycles") an
optimization was added to select_task_rq_rt() that immediately
returns when p->nr_cpus_allowed == 1 at the beginning of the
function.
This makes the latter p->nr_cpus_allowed > 1 check redundant,
which can now be removed.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: Mike Galbraith <mgalbraith@suse.de> Cc: tomk@rgmadvisors.com Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1380914693-24634-1-git-send-email-shawn.bohrer@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
While discussing the proposed SCHED_DEADLINE patches which in parts
mimic the existing FIFO code it was noticed that the wmb in
rt_set_overloaded() didn't have a matching barrier.
The only site using rt_overloaded() to test the rto_count is
pull_rt_task() and we should issue a matching rmb before then assuming
there's an rto_mask bit set.
Without that smp_rmb() in there we could actually miss seeing the
rto_mask bit.
Also, change to using smp_[wr]mb(), even though this is SMP only code;
memory barriers without smp_ always make me think they're against
hardware of some sort.
Commit 42eb088e (sched: Avoid NULL dereference on sd_busy) corrected a NULL
dereference on sd_busy but the fix also altered what scheduling domain it
used for the 'sd_llc' percpu variable.
One impact of this is that a task selecting a runqueue may consider
idle CPUs that are not cache siblings as candidates for running.
Tasks are then running on CPUs that are not cache hot.
This was found through bisection where ebizzy threads were not seeing equal
performance and it looked like a scheduling fairness issue. This patch
mitigates but does not completely fix the problem on all machines tested
implying there may be an additional bug or a common root cause. Here are
the average range of performance seen by individual ebizzy threads. It
was tested on top of candidate patches related to x86 TLB range flushing.
4-core machine
3.13.0-rc3 3.13.0-rc3
vanilla fixsd-v3r3
Mean 1 0.00 ( 0.00%) 0.00 ( 0.00%)
Mean 2 0.34 ( 0.00%) 0.10 ( 70.59%)
Mean 3 1.29 ( 0.00%) 0.93 ( 27.91%)
Mean 4 7.08 ( 0.00%) 0.77 ( 89.12%)
Mean 5 193.54 ( 0.00%) 2.14 ( 98.89%)
Mean 6 151.12 ( 0.00%) 2.06 ( 98.64%)
Mean 7 115.38 ( 0.00%) 2.04 ( 98.23%)
Mean 8 108.65 ( 0.00%) 1.92 ( 98.23%)
8-core machine
Mean 1 0.00 ( 0.00%) 0.00 ( 0.00%)
Mean 2 0.40 ( 0.00%) 0.21 ( 47.50%)
Mean 3 23.73 ( 0.00%) 0.89 ( 96.25%)
Mean 4 12.79 ( 0.00%) 1.04 ( 91.87%)
Mean 5 13.08 ( 0.00%) 2.42 ( 81.50%)
Mean 6 23.21 ( 0.00%) 69.46 (-199.27%)
Mean 7 15.85 ( 0.00%) 101.72 (-541.77%)
Mean 8 109.37 ( 0.00%) 19.13 ( 82.51%)
Mean 12 124.84 ( 0.00%) 28.62 ( 77.07%)
Mean 16 113.50 ( 0.00%) 24.16 ( 78.71%)
It's eliminated for one machine and reduced for another.
Signed-off-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Alex Shi <alex.shi@linaro.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: H Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/20131217092124.GV11295@suse.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Yinghai reported that he saw a /0 in sg_capacity on his EX parts.
Make sure to always initialize power_orig now that we actually use it.
Ideally build_sched_domains() -> init_sched_groups_power() would also
initialize this; but for some yet unexplained reason some setups seem
to miss updates there.
Reported-by: Yinghai Lu <yinghai@kernel.org> Tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/n/tip-l8ng2m9uml6fhibln8wqpom7@git.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 37dc6b50cee9 ("sched: Remove unnecessary iteration over sched
domains to update nr_busy_cpus") forgot to clear 'sd_busy' under some
conditions leading to a possible NULL deref in set_cpu_sd_state_idle().
Reported-by: Anton Blanchard <anton@samba.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20131118113701.GF3866@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
nr_busy_cpus parameter is used by nohz_kick_needed() to find out the
number of busy cpus in a sched domain which has SD_SHARE_PKG_RESOURCES
flag set. Therefore instead of updating nr_busy_cpus at every level
of sched domain, since it is irrelevant, we can update this parameter
only at the parent domain of the sd which has this flag set. Introduce
a per-cpu parameter sd_busy which represents this parent domain.
In nohz_kick_needed() we directly query the nr_busy_cpus parameter
associated with the groups of sd_busy.
By associating sd_busy with the highest domain which has
SD_SHARE_PKG_RESOURCES flag set, we cover all lower level domains
which could have this flag set and trigger nohz_idle_balancing if any
of the levels have more than one busy cpu.
sd_busy is irrelevant for asymmetric load balancing. However sd_asym
has been introduced to represent the highest sched domain which has
SD_ASYM_PACKING flag set so that it can be queried directly when
required.
While we are at it, we might as well change the nohz_idle parameter to
be updated at the sd_busy domain level alone and not the base domain
level of a CPU. This will unify the concept of busy cpus at just one
level of sched domain where it is currently used.
The rcu_try_advance_all_cbs() function is invoked on each attempted
entry to and every exit from idle. If this function determines that
there are callbacks ready to invoke, the caller will invoke the RCU
core, which in turn will result in a pair of context switches. If a
CPU enters and exits idle extremely frequently, this can result in
an excessive number of context switches and high CPU overhead.
This commit therefore causes rcu_try_advance_all_cbs() to throttle
itself, refusing to do work more than once per jiffy.
Reported-by: Tibor Billes <tbilles@gmx.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Tibor Billes <tbilles@gmx.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If a non-lazy callback arrives on a CPU that has previously gone idle
with no non-lazy callbacks, invoke_rcu_core() forces the RCU core to
run. However, it does not update the conditions, which could result
in several closely spaced invocations of the RCU core, which in turn
could result in an excessively high context-switch rate and resulting
high overhead.
This commit therefore updates the ->all_lazy and ->nonlazy_posted_snap
fields to prevent closely spaced invocations.
Reported-by: Tibor Billes <tbilles@gmx.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Tibor Billes <tbilles@gmx.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When restoring the PPR value, we incorrectly access the thread structure
at a time where MSR:RI is clear, which means we cannot recover from nested
faults. However the thread structure isn't covered by the "bolted" SLB
entries and thus accessing can fault.
This fixes it by splitting the code so that the PPR value is loaded into
a GPR before MSR:RI is cleared.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Asymmetric scheduling within a core is a scheduler loadbalancing
feature that is triggered when SD_ASYM_PACKING flag is set. The goal
for the load balancer is to move tasks to lower order idle SMT threads
within a core on a POWER7 system.
In nohz_kick_needed(), we intend to check if our sched domain (core)
is completely busy or we have idle cpu.
already covers the case of checking if the domain has an idle cpu,
because cpumask_first_and() will not yield any set bits if this domain
has no idle cpu.
Hence, nr_busy check against group weight can be removed.
f41f064cf4 ("PCI: Workaround missing pci_set_master in pci drivers") made
pci_enable_bridge() turn on bus mastering if the driver hadn't done so
already. It also added a warning in this case. But there's no reason to
warn about it unless it's actually a problem to enable bus mastering here.
This patch drops the warning because I'm not aware of any such problem.
RCU and the fine grained idle time accounting functions check
tick_nohz_enabled. But that variable is merily telling that NOHZ has
been enabled in the config and not been disabled on the command line.
But it does not tell anything about nohz being active. That's what all
this should check for.
Matthew reported, that the idle accounting on his old P1 machine
showed bogus values, when he enabled NOHZ in the config and did not
disable it on the kernel command line. The reason is that his machine
uses (refined) jiffies as a clocksource which explains why the "fine"
grained accounting went into lala land, because it depends on when the
system goes and leaves idle relative to the jiffies increment.
Provide a tick_nohz_active indicator and let RCU and the accounting
code use this instead of tick_nohz_enable.
Reported-and-tested-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: john.stultz@linaro.org Cc: mwhitehe@redhat.com Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1311132052240.30673@ionos.tec.linutronix.de Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If CONFIG_NO_HZ=n tick_nohz_get_sleep_length() returns NSEC_PER_SEC/HZ.
If CONFIG_NO_HZ=y and the nohz functionality is disabled via the
command line option "nohz=off" or not enabled due to missing hardware
support, then tick_nohz_get_sleep_length() returns 0. That happens
because ts->sleep_length is never set in that case.
Set it to NSEC_PER_SEC/HZ when the NOHZ mode is inactive.
Reported-by: Michal Hocko <mhocko@suse.cz> Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When debugging the read-only hugepage case, I was confused by the fact
that get_futex_key() did an access_ok() only for the non-shared futex
case, since the user address checking really isn't in any way specific
to the private key handling.
Now, it turns out that the shared key handling does effectively do the
equivalent checks inside get_user_pages_fast() (it doesn't actually
check the address range on x86, but does check the page protections for
being a user page). So it wasn't actually a bug, but the fact that we
treat the address differently for private and shared futexes threw me
for a loop.
Just move the check up, so that it gets done for both cases. Also, use
the 'rw' parameter for the type, even if it doesn't actually matter any
more (it's a historical artifact of the old racy i386 "page faults from
kernel space don't check write protections").
The dmi_list array is initialized using gnu designated initializers, and
therefore may contain fewer explicitly defined entries as there are
elements in it. This is because the enum above with M_xyz constants
contains more items than the designated initializer. Those elements not
explicitly initialized are implicitly set to 0.
Now efifb_setup() loops through all these array elements, and performs
a strcmp on each item. For non explicitly initialized elements this will
be a null pointer:
This patch swaps the check order in the if statement, thus checks first
whether dmi_list[i].base is null.
Signed-off-by: James Bates <james.h.bates@gmail.com> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently each task sends BLK_TN_PROCESS event to the first traced
device it interacts with after a new trace is started. When there are
several traced devices and the task accesses more devices, this logic
can result in BLK_TN_PROCESS being sent several times to some devices
while it is never sent to other devices. Thus blkparse doesn't display
command name when parsing some blktrace files.
Fix the problem by sending BLK_TN_PROCESS event to all traced devices
when a task interacts with any of them.
Signed-off-by: Jan Kara <jack@suse.cz> Review-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates SB800 prefetch routine
in AMD PLL quirk. And make it use the new chipset type to represent SB800
generation.
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates USB subsystem hang
symptom quirk which is observed on AMD all SB600 and SB700 revision
0x3a/0x3b. And make it use the new chipset type to represent.
This patch abstracts out a AMD chipset type which includes southbridge
generation and its revision. When os excutes usb_amd_find_chipset_info
routine to initialize AMD chipset type, driver will know which kind of
chipset is used.
This update has below benifits:
- Driver is able to confirm which southbridge generations and their
revision are used, with chipset detection once.
- To describe chipset generations with enumeration types brings better
readability.
- It's flexible to filter AMD platforms to implement new quirks in future.
There is a small gap between the jack detection unsolicited event and
the time the ELD is updated. When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.
For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated. The
workaround is imperfect, but good enough as a starting point.
The device IDs of the AMD Cypress/Juniper/Redwood/Cedar/Cayman/Antilles/
Barts/Turks/Caicos HDMI HDA controllers weren't added explicitly
because the generic entry works, but it made the device appearing as
"Generic", and people are confused as if it's no proper HDMI
controller. Add them so that the name shows up properly as "ATI HDMI"
instead of "Generic".
According to Takashi's tests and the lack of complaints, these devices
work fine without disabling snooping.
The function name not_share_unassigned_cvt() is opposite to what it does.
This patch renames it to intel_not_share_assigned_cvt(), and addes comments
to explain why some Intel display codecs need this workaround.
For Valleyview display codec, if an unused pin chooses an assgined converter
selected by a used pin, playback on the unused pin can also give sound to the
output device of the used pin. It's because data flows from the same convertor
to the display port of the used pin. This issue is same as Haswell.
So this patch avoids using assinged convertors for unused pins.
The related function haswell_config_cvts() is renamed for code reuse.
Since the lock is used primarily in patch_hdmi.c, it's better to move
it in the local struct instead of exporting in hda_eld. The only
functions requiring the lock in hda_eld.c are proc accessors. So in
this patch, the proc entry and its creation/deletion/accessors are
moved into patch_hdmi.c, together with the mutex lock to pin_spec
struct.
The former proc info functions are exported so that they can be called
from patch_hdmi.c.
Some per_pin fields and ELD contents might be changed dynamically in
multiple ways where the concurrent accesses are still opened in the
current code. This patch fixes such possible races by using eld->lock
in appropriate places.
For some speakers and slots the CEA slot <-> speaker assignment depends
on the used CEA Channel Allocation value.
Therefore the from_cea_slot() and to_cea_slot() helpers currently only
work correctly for the regular 7.1 speakers.
Fix them to work with all speakers, taking the re-ordered CA index as
input and adapting use sites accordingly.
This change allows manual channel mapping to actually work for all CEA
allocated speakers. Additionally, this fixes incorrect channel map
reporting in automatic channel mapping mode when an affected speaker
position is used (e.g. 6.1 map which contains an RC speaker).
hdmi_manual_setup_channel_mapping() and hdmi_std_setup_channel_mapping
try to assign ALSA channels to HDMI channel slots and disable (i.e.
silence) other slots.
However, they try to disable a slot by using AC_VERB_SET_CHAN_SLOT with
parameter ((alsa_ch << 8) | 0xf), while the correct parameter is
((0xf << 8) | hdmi_slot), i.e. the slot should be unassigned, not the
ALSA channel.
Fix that by actually disabling the unused slots.
Note that this bug did not cause any (reported) issues because slots
incorrectly having audio are normally ignored by a receiver if the CEA
channel allocation used does not map that slot to any speaker.
Additionally, the converter channel count configuration limits the
number of actually active channels in any case.
Currently the converter channel count is set to the number of actual
input channels. The audio infoframe channel count field is set
similarly.
However, sometimes the used channel map does not map all input channels
to outputs. Notably, 3 channel modes (e.g. 2.1) require a dummy input
channel so there are 4 input channels. According to the HDA
specification, converter channel count should be programmed according to
the number of _active_ channels.
On Intel HDMI codecs (but not on NVIDIA), setting the converter channel
to a higher value than there are actually mapped channels to HDMI slots
will cause no audio to be output at all.
Note that the effects of this issue are currently partially masked by
other bugs that prevent the driver from actually unmapping channels in
certain cases. For example, if a 4 channel stream is first created and
prepared, it gets a FL,FR,RL,RR mapping (ALSA->HDMI slot mapping 0->0,
1->1, 2->4, 3->5). If one thereafter assigns a FR,FL,FC mapping to it,
the driver will remap 2->3 but fail to unmap 2->4 and 3->5, so there are
still 4 active channels and the issue will not trigger in this case.
These bugs will be fixed separately.
Fix the channel counts in the converter channel count field and in the
audio infoframe channel count field to match the actual number of active
channels.
hdmi_std_setup_channel_mapping() selects a Channel Allocation according
to the sink reported speaker mask, preferring the ALSA standard layouts.
If the channel allocation is not one of the ALSA standard layouts, the
ALSA channels are mapped directly to HDMI channels in order. However,
the function does not take into account that there a holes in the HDMI
channel map.
Additionally, the function tries to disable a slot by using
AC_VERB_SET_CHAN_SLOT with parameter ((alsa_ch << 8) | 0xf), while the
correct parameter is ((0xf << 8) | hdmi_slot), i.e. the slot should be
unassigned, not the ALSA channel.
Fix both of the issues for non-ALSA-default layouts.
Tested on Intel HDMI with a speaker mask of FL | FR | FC | RC, which
causes CA 0x06 to be selected for 4-channel audio, which causes
incorrect output (sound destined to RC goes to FC and FC goes nowhere)
without the patch.
Git commit 4f37a68cdaf6dea833cfdded2a3e0c47c0f006da
"s390: Use direct ktime path for s390 clockevent device" makes use
of the CLOCK_EVT_FEAT_KTIME clockevent option to avoid the delta
calculation with ktime_get() in clockevents_program_event and the
get_tod_clock() in s390_next_event. This is based on the assumption
that the difference between the internal ktime and the hardware
clock is reflected in the wall_to_monotonic delta. But this is not
true, the ntp corrections are applied via changes to the tk->mult
multiplier and this is not reflected in wall_to_monotonic.
In theory this could be solved by using the raw monotonic clock
but it is simpler to switch back to the standard clock delta
calculation.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Unloading the fs3270 kernel module does not remove the created
"3270/tub" device. Reloading the module then causes a sysfs warning:
"sysfs: cannot create duplicate filename '/devices/virtual/3270/3270!tub'".
Call device_destroy() in the module exit function to solve this issue.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
More people have reported they need this for their machines to work
correctly.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60682 Reported-by: Stefan Hellermann <bugzilla.kernel.org@the2masters.de> Reported-by: Benedikt Sauer <filmor@gmail.com> Reported-by: Erno Kuusela <erno@iki.fi> Reported-by: Jonathan Doman <jonathan.doman@gmail.com> Reported-by: Christoph Klaffl <christophklaffl@gmail.com> Reported-by: Jan Hendrik Nielsen <jan.hendrik.nielsen@informatik.hu-berlin.de> Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Properly clear the enable bit when audio disable is requested.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
dm_pool_close_thin_device() must be called if dm_set_target_max_io_len()
fails in thin_ctr(). Otherwise __pool_destroy() will fail because the
pool will still have an open thin device:
device-mapper: thin metadata: attempt to close pmd when 1 device(s) are still open
device-mapper: thin: __pool_destroy: dm_pool_metadata_close() failed.
Also, must establish error code if failing thin_ctr() because the pool
is in fail_io mode.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 905e51b ("dm thin: commit outstanding data every second")
introduced a periodic commit. This commit occurs regardless of whether
any thin devices have made changes.
Fix the periodic commit to check if any of a pool's thin devices have
changed using dm_pool_changed_this_transaction().
Reported-by: Alexander Larsson <alexl@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
An invalid ioctl will never be valid, irrespective of whether multipath
has active paths or not. So for invalid ioctls we do not have to wait
for multipath to activate any paths, but can rather return an error
code immediately. This fix resolves numerous instances of:
udevd[]: worker [] unexpectedly returned with status 0x0100
that have been seen during testing.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It appears that in the DMA40 driver the DMA tasklet will very
often dereference memory for a descriptor just free:d from the
DMA40 slab. Nothing happens because no other part of the driver
has yet had a chance to claim this memory, but it's really
nasty to dereference free:d memory, so let's check the flag
before the descriptor is free and store it in a bool variable.
During restore, pm_notifier chain are called with
PM_RESTORE_PREPARE. The firmware_class driver handler
fw_pm_notify does not have a handler for this. As a result,
it keeps a reader on the kmod.c umhelper_sem. During
freeze_processes, the call to __usermodehelper_disable tries to
take a write lock on this semaphore and hangs waiting.
Signed-off-by: Sebastian Capella <sebastian.capella@linaro.org> Acked-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
pci_get_device() decrements the reference count of "from" (last
argument) so when we break off the loop successfully we have only one
device reference - and we don't know which device we have. If we want
a reference to each device, we must take them explicitly and let
the pci_get_device() walk complete to avoid duplicate references.
This is serious, as over-putting device references will cause
the device to eventually disappear. Without this fix, the kernel
crashes after a few insmod/rmmod cycles.
Tested on an Intel S7000FC4UR system with a 7300 chipset.
A selective retransmission request (SRR) is a fibre-channel
protocol control request which provides support for requesting
retransmission of a data sequence in response to an issue such as
frame loss or corruption. These events are experienced
infrequently in fibre-channel based networks which makes
it difficult to test and assess codepaths which handle these
events.
We were fortunate enough, for some definition of fortunate, to
have a metro-area single-mode SAN link which, at 10 GBPS
sustained load levels, would consistently generate SRR's in
a SCST based target implementation using our SCST/in-kernel
Qlogic target interface driver. In response to an SRR the
in-kernel Qlogic target driver immediately panics resulting
in a catastrophic storage failure for serviced initiators.
The culprit was a debug statement in the qla_target.c file which
does not verify that a pointer to the SCSI CDB is not null.
The unchecked pointer dereference results in the kernel panic
and resultant system failure.
The other two references to the SCSI CDB by the SRR handling code
use a ternary operator to verify a non-null pointer is being
acted on. This patch simply adds a similar test to the implicated
debug statement.
This patch is a candidate for any stable kernel being maintained
since it addresses a potentially catastrophic event with
minimal downside.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / people / ms / linux.git / log
