Stephen Boyd [Fri, 6 Apr 2018 20:21:45 +0000 (13:21 -0700)]
Merge branches 'clk-spreadtrum', 'clk-stm32f', 'clk-stm32mp1', 'clk-hi655x' and 'clk-gpio' into clk-next
* clk-spreadtrum:
clk: sprd: add RTC gate for SC9860
dt-bindings: clocks: add APB RTC gate for SC9860
* clk-stm32f:
clk: stm32: Add clk entry for SDMMC2 on stm32F769
clk: stm32: Add DSI clock for STM32F469 Board
clk: stm32: END_PRIMARY_CLK should be declare after CLK_SYSCLK
* clk-stm32mp1:
clk: stm32: add configuration flags for each of the stm32 drivers
clk: stm32mp1: add Debug clocks
clk: stm32mp1: add MCO clocks
clk: stm32mp1: add RTC clock
clk: stm32mp1: add Peripheral & Kernel Clocks
clk: stm32mp1: add Kernel timers
clk: stm32mp1: add Sub System clocks
clk: stm32mp1: add Post-dividers for PLL
clk: stm32mp1: add PLL clocks
clk: stm32mp1: add Source Clocks for PLLs
clk: stm32mp1: add MP1 gate for hse/hsi/csi oscillators
clk: stm32mp1: Introduce STM32MP1 clock driver
dt-bindings: Document STM32MP1 Reset Clock Controller (RCC) bindings
* clk-hi655x:
clk: enable hi655x common clk automatically
* clk-gpio:
clk: clk-gpio: Allow GPIO to sleep in set/get_parent
Stephen Boyd [Fri, 6 Apr 2018 20:21:33 +0000 (13:21 -0700)]
Merge branches 'clk-ti', 'clk-amlogic', 'clk-tegra' and 'clk-samsung' into clk-next
* clk-ti:
clk: keystone: sci-clk: add support for dynamically probing clocks
clk: ti: add support for clock latching to mux clocks
clk: ti: add support for clock latching to divider clocks
clk: ti: add generic support for clock latching
clk: ti: add support for register read-modify-write low-level operation
dt-bindings: clock: ti: add latching support to mux and divider clocks
* clk-amlogic: (50 commits)
clk: meson: Drop unused local variable and add static
clk: meson: clean-up clk81 clocks
clk: meson: add fdiv clock gates
clk: meson: add mpll pre-divider
clk: meson: axg: add hifi pll clock
clk: meson: axg: add hifi clock bindings
clk: meson: add ROUND_CLOSEST to the pll driver
clk: meson: add gp0 frac parameter for axg and gxl
clk: meson: improve pll driver results with frac
clk: meson: remove special gp0 lock loop
clk: meson: poke pll CNTL last
clk: meson: add fractional part of meson8b fixed_pll
clk: meson: use hhi syscon if available
clk: meson: remove obsolete cpu_clk
clk: meson: rework meson8b cpu clock
clk: meson: split divider and gate part of mpll
clk: meson: migrate plls clocks to clk_regmap
clk: meson: migrate the audio divider clock to clk_regmap
clk: meson: migrate mplls clocks to clk_regmap
clk: meson: add regmap helpers for parm
...
* clk-tegra:
clk: tegra: Fix pll_u rate configuration
clk: tegra: Specify VDE clock rate
clk: tegra20: Correct PLL_C_OUT1 setup
clk: tegra: Mark HCLK, SCLK and EMC as critical
clk: tegra: MBIST work around for Tegra210
clk: tegra: add fence_delay for clock registers
clk: tegra: Add la clock for Tegra210
* clk-samsung: (22 commits)
clk: samsung: Mark a few things static
clk: samsung: Add fout=196608001 Hz EPLL rate entry for exynos4412
clk: samsung: exynos5250: Add missing clocks for FIMC LITE SYSMMU devices
clk: samsung: exynos5420: Add more entries to EPLL rate table
clk: samsung: exynos5420: Add CLK_SET_RATE_PARENT flag to mout_mau_epll_clk
clk: samsung: exynos5250: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: exynos5420: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: Add Exynos5 sub-CMU clock driver
soc: samsung: pm_domains: Add blacklisting clock handling
clk: samsung: Add compile time PLL rate validators
clk: samsung: s3c2410: Fix PLL rates
clk: samsung: exynos7: Fix PLL rates
clk: samsung: exynos5433: Fix PLL rates
clk: samsung: exynos5260: Fix PLL rates
clk: samsung: exynos5250: Fix PLL rates
clk: samsung: exynos3250: Fix PLL rates
clk: exynos5433: Extend list of available AUD_PLL output frequencies
clk: exynos5433: Add CLK_IGNORE_UNUSED flag to sclk_ioclk_i2s1_bclk
clk: samsung: Add a git tree entry to MAINTAINERS
clk: samsung: Remove redundant dev_err call in exynos_audss_clk_probe()
...
Weiyi Lu [Mon, 12 Mar 2018 07:03:42 +0000 (15:03 +0800)]
clk: mediatek: update clock driver of MT2712
According to ECO design change,
1. add new clock mux data and change some
2. add new clock gate data and clock factor data
3. change status register offset of infra subsystem
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It exposes an issue that clk core, clk_core_get_phase, always
returns the cached core->phase which should be either updated
by calling clk_set_phase or directly from the first place the
clk was registered.
When registering the clk, the core->phase geting from ->get_phase()
may return negative value indicating error. This is quite common
since the clk's phase may be highly related to its parent chain,
but it was temporarily orphan when registered, since its parent
chains hadn't be ready at that time, so the clk drivers decide to
return error in this case. However, if no clk_set_phase is called or
maybe the ->set_phase() isn't even implemented, the core->phase would
never be updated. This is wrong, and we should try to update it when
all its parent chains are settled down, like the way of updating clock
rate for that. But it's not deserved to complicate the code now and
just update it anyway when calling clk_core_get_phase, which would be
much simple and enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Acked-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Richard Genoud [Tue, 13 Mar 2018 15:27:02 +0000 (16:27 +0100)]
clk: mvebu: armada-38x: add support for missing clocks
Clearfog boards can come with a CPU clocked at 1600MHz (commercial)
or 1333MHz (industrial).
They have also some dip-switches to select a different clock (666, 800,
1066, 1200).
The funny thing is that the recovery button is on the MPP34 fq selector.
So, when booting an industrial board with this button down, the frequency
666MHz is selected (and the kernel didn't boot).
This patch add all the missing clocks.
The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ).
Fixes: 0e85aeced4d6 ("clk: mvebu: add clock support for Armada 380/385") Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f56cf5: clk: mvebu: armada-38x: add support for 1866MHz variants Cc: <stable@vger.kernel.org> # 3.16.x Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Mike Looijmans [Tue, 13 Mar 2018 08:54:03 +0000 (09:54 +0100)]
clk: clk-gpio: Allow GPIO to sleep in set/get_parent
When changing or retrieving clock parents, the caller is in a sleepable
state (like prepare) so the GPIO operation need not be atomic. Replace
gpiod_{g|s}et_value with gpiod_{g|s}et_value_cansleep in the {g|s}et_parent
calls for the GPIO based clock mux.
This fixes a "slowpath" warning when the GPIO controller is an I2C expander
or something similar.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Riku Voipio [Mon, 12 Mar 2018 10:49:45 +0000 (12:49 +0200)]
clk: enable hi655x common clk automatically
Without COMMON_CLK_HI655X Wifi and bluetooth are non-functional on Hikey.
As suggested by Arnd, enable the driver automatically when the parent
driver is selected. With sensible defaults in place, we can leave other
choices for EXPERT.
Cc: John Stultz <john.stultz@linaro.org> Cc: Wei Xu <xuwei5@hisilicon.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Suggested-by: Arnd Bergmann <arnd@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@linaro.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk: stm32: add configuration flags for each of the stm32 drivers
Add two configuration flags to be able to not compile all the time
stm32f and stm32h7 drivers when ARCH_STM32 is set.
That help to save some space on those small platforms.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk: stm32: END_PRIMARY_CLK should be declare after CLK_SYSCLK
Update of END_PRIMARY_CLK was missed, it should be after CLK_SYSCLK
hsi and sysclk are overwritten by gpioa and gpiob.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Gregory CLEMENT [Wed, 28 Feb 2018 14:07:51 +0000 (15:07 +0100)]
clk: mvebu: cp110: Fix clock tree representation
Thanks to new documentation, we have a better view of the clock tree.
There were few mistakes in the first version of this driver, the main one
being the parental link between the clocks. Actually the tree is more
flat that we though. Most of the IP blocks require two clocks: one for
the IP itself and one for accessing the registers, and unlike what we
wrote there is no link between these two clocks.
The other mistakes were about the name of the clocks: the root clock is
not the Audio PLL but the PLL0, and what we called the EIP clock is named
the x2 Core clock and is used by other IP block than the EIP ones.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Dong Aisheng [Tue, 23 Jan 2018 12:24:45 +0000 (20:24 +0800)]
clk: add more __must_check for bulk APIs
we need it even when !CONFIG_HAVE_CLK because it allows
us to catch missing checking return values in the non-clk
compile configurations too. More test coverage.
Cc: Stephen Boyd <sboyd@codeaurora.org> Suggested-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Dong Aisheng [Fri, 19 Jan 2018 13:37:15 +0000 (21:37 +0800)]
Documentation: clk: enable lock is not held for clk_is_enabled API
The core does not need to hold enable lock for clk_is_enabled API.
Update the doc to reflect it.
Cc: Jonathan Corbet <corbet@lwn.net> Cc: Stephen Boyd <sboyd@codeaurora.org> Suggested-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd: Clarified the last sentence a little more and fixed a spelling
error] Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk: qcom: gcc-msm8996: Mark aggre0 noc clks as critical
aggre0 bus clks are not associated with any of the drivers, so its
important that these clks are always on to get peripherals on this
bus working. So mark them as critical.
Eventually when we have a proper bus driver these clks can be marked
appropriately.
Without this patch pcie on db820c is not functional.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Brian Starkey [Mon, 13 Nov 2017 15:27:51 +0000 (15:27 +0000)]
clk: versatile: Remove WARNs in ->round_rate()
clk_round_rate() is intended to be used to round a given clock rate to
the closest one achievable by the actual clock. This implies that the
input to clk_round_rate() is expected to be unachievable - and such
cases shouldn't be treated as exceptional.
To reflect this, remove the WARN_ONs which trigger when an unachievable
clock rate is passed to vexpress_osc_round_rate().
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Brian Starkey <brian.starkey@arm.com> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Sudeep Holla [Fri, 10 Nov 2017 16:06:57 +0000 (16:06 +0000)]
clk: versatile: add min/max rate boundaries for vexpress osc clock
Clock framework has a provider API(clk_hw_set_rate_range) to set the
min/max rate of a clock. Use the same to set the boundaries for the
vexpress osc clock.
Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: linux-clk@vger.kernel.org Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stephen Boyd [Fri, 16 Mar 2018 16:21:40 +0000 (09:21 -0700)]
clk: samsung: Mark a few things static
Running sparse on the samsung clk directory has some noise that we can
fix to look for future problems easier.
drivers/clk/samsung/clk-s3c2443.c:111:26: warning: symbol 's3c2443_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:139:26: warning: symbol 's3c2443_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:152:27: warning: symbol 's3c2443_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:186:28: warning: symbol 's3c2443_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:241:26: warning: symbol 's3c2416_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:247:26: warning: symbol 's3c2416_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:253:27: warning: symbol 's3c2416_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:263:28: warning: symbol 's3c2416_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:291:26: warning: symbol 's3c2443_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:296:27: warning: symbol 's3c2443_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:305:28: warning: symbol 's3c2443_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:321:26: warning: symbol 's3c2450_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:328:26: warning: symbol 's3c2450_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:334:27: warning: symbol 's3c2450_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:345:28: warning: symbol 's3c2450_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:368:33: warning: symbol 's3c2443_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:464:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:470:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:476:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2412.c:96:26: warning: symbol 's3c2412_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:108:35: warning: symbol 's3c2412_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:128:26: warning: symbol 's3c2412_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:146:27: warning: symbol 's3c2412_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:177:28: warning: symbol 's3c2412_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:227:33: warning: symbol 's3c2412_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:292:43: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:98:26: warning: symbol 's3c2410_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:114:26: warning: symbol 's3c2410_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:119:27: warning: symbol 's3c2410_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:138:28: warning: symbol 's3c2410_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:203:26: warning: symbol 's3c2410_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:207:35: warning: symbol 's3c2410_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:218:28: warning: symbol 's3c2410_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:272:26: warning: symbol 's3c244x_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:277:35: warning: symbol 's3c244x_common_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:294:26: warning: symbol 's3c244x_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:302:27: warning: symbol 's3c244x_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:306:28: warning: symbol 's3c244x_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:321:26: warning: symbol 's3c2440_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:325:27: warning: symbol 's3c2440_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:331:35: warning: symbol 's3c2442_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:337:26: warning: symbol 's3c2442_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:346:33: warning: symbol 's3c2410_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:471:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:477:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:483:49: warning: Using plain integer as NULL pointer
Stephen Boyd [Fri, 16 Mar 2018 16:11:27 +0000 (09:11 -0700)]
Merge tag 'clk-v4.17-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-samsung
Pull samsung clk driver updates from Sylwester Nawrocki:
This change set includes the PLL rate definition fixes and an addition
of compile time PLL rate validation macros. It adds definitions of some
missing clocks and extends the PLL rate tables required in the sound
subsystem.
In order to handle dependencies of clocks on the power domains a clock
provider sub-driver is added for Exynos5 SoCs. In newer Exynos SoCs
there is no need to do such things as the clocks/power domain relations
are more clearly defined and better documented.
* tag 'clk-v4.17-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk: (21 commits)
clk: samsung: Add fout=196608001 Hz EPLL rate entry for exynos4412
clk: samsung: exynos5250: Add missing clocks for FIMC LITE SYSMMU devices
clk: samsung: exynos5420: Add more entries to EPLL rate table
clk: samsung: exynos5420: Add CLK_SET_RATE_PARENT flag to mout_mau_epll_clk
clk: samsung: exynos5250: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: exynos5420: Move PD-dependent clocks to Exynos5 sub-CMU
clk: samsung: Add Exynos5 sub-CMU clock driver
soc: samsung: pm_domains: Add blacklisting clock handling
clk: samsung: Add compile time PLL rate validators
clk: samsung: s3c2410: Fix PLL rates
clk: samsung: exynos7: Fix PLL rates
clk: samsung: exynos5433: Fix PLL rates
clk: samsung: exynos5260: Fix PLL rates
clk: samsung: exynos5250: Fix PLL rates
clk: samsung: exynos3250: Fix PLL rates
clk: exynos5433: Extend list of available AUD_PLL output frequencies
clk: exynos5433: Add CLK_IGNORE_UNUSED flag to sclk_ioclk_i2s1_bclk
clk: samsung: Add a git tree entry to MAINTAINERS
clk: samsung: Remove redundant dev_err call in exynos_audss_clk_probe()
clk: samsung: Remove redundant dev_err call in exynos5433_cmu_probe()
...
Stephen Boyd [Fri, 16 Mar 2018 16:09:49 +0000 (09:09 -0700)]
Merge tag 'tegra-for-4.17-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-tegra
Pull tegra clk driver updates from Thierry Reding:
This contains preliminary work for the MBIST workaround implemented in
the Tegra PMC driver. There's also some fixes to various clocks for bugs
that went unnoticed for a long time.
* tag 'tegra-for-4.17-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Fix pll_u rate configuration
clk: tegra: Specify VDE clock rate
clk: tegra20: Correct PLL_C_OUT1 setup
clk: tegra: Mark HCLK, SCLK and EMC as critical
clk: tegra: MBIST work around for Tegra210
clk: tegra: add fence_delay for clock registers
clk: tegra: Add la clock for Tegra210
Stephen Boyd [Wed, 14 Mar 2018 22:36:31 +0000 (15:36 -0700)]
clk: meson: Drop unused local variable and add static
Fixes the following warnings:
drivers/clk/meson/meson8b.c:512:19: warning: symbol 'meson8b_mpeg_clk_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:526:19: warning: symbol 'meson8b_clk81' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:540:19: warning: symbol 'meson8b_cpu_in_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:591:19: warning: symbol 'meson8b_cpu_scale_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:608:19: warning: symbol 'meson8b_cpu_scale_out_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:626:19: warning: symbol 'meson8b_cpu_clk' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:392:27: warning: symbol 'gxbb_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:439:27: warning: symbol 'gxl_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:195:27: warning: symbol 'axg_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:248:27: warning: symbol 'axg_hifi_init_regs' was not declared. Should it be static?
drivers/clk/meson/meson8b.c: In function 'meson8b_clkc_probe':
drivers/clk/meson/meson8b.c:1052:14: warning: unused variable 'clk' [-Wunused-variable]
Stephen Boyd [Wed, 14 Mar 2018 21:44:55 +0000 (14:44 -0700)]
Merge tag 'ti-clk-for-4.17' of https://github.com/t-kristo/linux-pm into clk-ti
Pull TI SoC clock updates for 4.17 from Tero Kristo:
* tag 'ti-clk-for-4.17' of https://github.com/t-kristo/linux-pm:
clk: keystone: sci-clk: add support for dynamically probing clocks
clk: ti: add support for clock latching to mux clocks
clk: ti: add support for clock latching to divider clocks
clk: ti: add generic support for clock latching
clk: ti: add support for register read-modify-write low-level operation
dt-bindings: clock: ti: add latching support to mux and divider clocks
Marek Szyprowski [Tue, 13 Mar 2018 10:46:12 +0000 (11:46 +0100)]
clk: samsung: exynos5250: Add missing clocks for FIMC LITE SYSMMU devices
FIMC LITE SYSMMU devices are defined in exynos5250.dtsi, but clocks for
them are not instantiated by Exynos5250 clock provider driver. Add needed
definitions for those clocks to fix IOMMU probe failure:
ERROR: could not get clock /soc/sysmmu@13c40000:sysmmu(0)
exynos-sysmmu 13c40000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c40000.sysmmu failed with error -38
ERROR: could not get clock /soc/sysmmu@13c50000:sysmmu(0)
exynos-sysmmu 13c50000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c50000.sysmmu failed with error -38
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: bfed1074f213 ("clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks") Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Jerome Brunet [Mon, 19 Feb 2018 11:21:46 +0000 (12:21 +0100)]
clk: meson: clean-up clk81 clocks
clk81 is a composite clock which parents all the peripheral clocks of the
platform. It is a critical clock which is used as provided by the
bootloader. We don't want to change its rate or reparent it, ever.
Remove the CLK_IGNORE_UNUSED on the mux and divider. These clock can't
gate so the flag is useless, and the gate is already critical, so the
clock won't ever be unused.
Remove CLK_SET_RATE_NO_REPARENT from mux, it is useless since the mux is
read-only.
Remove CLK_SET_RATE_PARENT from the gate and divider and use ro_ops for
the divider. A peripheral clock should not try to change the rate of
clk81. Stopping the rate propagation is good way to make sure such request
would be ignored.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 19 Feb 2018 11:21:45 +0000 (12:21 +0100)]
clk: meson: add fdiv clock gates
Fdiv fixed dividers clocks of the fixed_pll can actually gate
independently. We never had an issue so far because these clocks
were provided 'enabled' by the bootloader.
Add these gates to enable/disable the clocks when required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 19 Feb 2018 11:21:44 +0000 (12:21 +0100)]
clk: meson: add mpll pre-divider
mpll clocks parent can actually be divided by 1 or 2. So far, this
divider has always been set to 1, so the calculation was correct.
Now that we know it exists, model the tree correctly. If we ever get
a platform where the divider is different, we won't get into trouble
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 19 Feb 2018 11:21:43 +0000 (12:21 +0100)]
clk: meson: axg: add hifi pll clock
Add the hifi pll to the axg clock controller. This clock maybe used as an
input of the axg audio clock controller. It uses the same settings table
as the gp0 pll but has a frac parameter allowing more precision.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 19 Feb 2018 11:21:39 +0000 (12:21 +0100)]
clk: meson: improve pll driver results with frac
Finding the appropriate settings of meson plls is too tricky to be done
entirely at runtime, using calculation only. Many combination of m, n
and od won't lock which is why we are using a table for this. However,
for plls having a fractional parameters, it is possible to improve on
the result provided by the table by calculating the frac parameter.
This change adds the calculation of frac when the parameter is available
and the rate provided by the table is not an exact match for the
requested rate.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 19 Feb 2018 11:21:37 +0000 (12:21 +0100)]
clk: meson: poke pll CNTL last
Poking CNTL first may take the PLL out of reset while we are still
applying the initial settings, including the filter values
initialization. This is the case for the axg and gxl gp0 pll.
Doing this poke last ensures the pll stays in reset while the initial
settings are applied.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:46 +0000 (15:58 +0100)]
clk: meson: use hhi syscon if available
On gxbb and axg, try to get the hhi regmap from the parent DT node, which
should be the HHI system controller once the necessary changes have been
made in amlogic's DTs
Until then, if getting regmap through the system controller fails, the
clock controller will fall back to the old way, requesting memory region
directly and then registering the regmap itself.
This should allow a smooth transition to syscon
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:44 +0000 (15:58 +0100)]
clk: meson: rework meson8b cpu clock
Instead of migrating meson cpu_clk to clk_regmap, like the other meson
clock drivers, we take advantage of the massive rework to get rid of it
completely, and solve (the first part) of the related FIXME notice.
As pointed out in the code comments, the cpu_clk should be modeled with
dividers and muxes it is made of, instead of one big composite clock.
The cpu_clk was not working correctly to enable dvfs on meson8b. It hangs
quite often when changing the cpu clock rate. This new implementation,
based on simple elements improves the situation but the platform will
still hang from time to time. This is not acceptable so, until we can
make the mechanism around the cpu clock stable, the cpu clock subtree
has been put in read-only mode, preventing any change of the cpu clock
The notifier and read-write operation will be added back when we have a
solution to the problem.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:43 +0000 (15:58 +0100)]
clk: meson: split divider and gate part of mpll
The mpll clock is a kind of fractional divider which can gate.
When the RW operation have been added, enable/disable ops have been
mistakenly inserted in this driver. These ops are essentially a
poor copy/paste of the generic gate ops.
This change removes the gate ops from the mpll driver and inserts a
generic gate clock on each mpll divider, simplifying the mpll
driver and reducing code duplication.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:42 +0000 (15:58 +0100)]
clk: meson: migrate plls clocks to clk_regmap
Rework meson pll driver to use clk_regmap and move meson8b, gxbb and
axg's clock using meson_clk_pll to clk_regmap.
This rework is not just about clk_regmap, there a serious clean-up of
the driver code:
* Add lock and reset field: Previously inferred from the n field.
* Simplify the reset logic: Code seemed to apply reset differently but
in fact it was always the same -> assert reset, apply params,
de-assert reset. The 2 lock checking loops have been kept for now, as
they seem to be necessary.
* Do the sequence of init register pokes only at .init() instead of in
.set_rate(). Redoing the init on every set_rate() is not necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:39 +0000 (15:58 +0100)]
clk: meson: add regmap helpers for parm
Meson clock drivers are using struct parm to describe each field of the
clock provider. Providing helpers to access these fields with regmap
helps to keep drivers readable
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:35 +0000 (15:58 +0100)]
clk: meson: add regmap to the clock controllers
This change registers a regmap in meson8b, gxbb and axg controllers.
The clock are still accessing their registers directly through iomem.
Once all clocks handled by these controllers have been move to regmap,
the regmap register will be removed and replaced with a syscon request.
This is needed because other drivers, such as the HDMI driver, need to
access the HHI register region
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:32 +0000 (15:58 +0100)]
clk: meson: add regmap clocks
Meson clock controllers need to move the classical iomem registers to
regmap. This is triggered because the HHI controllers found on the GXBB
and GXL host more than just clocks. To properly handle this, we would
like to migrate HHI to syscon. Also GXBB AO clock controller already use
regmap, AXG AO and Audio clock controllers will as well.
The purpose of this change is to provide a common structure to these
meson controllers (and possibly others) for regmap based clocks.
This change provides the basic gate, mux and divider, based on the
helpers provided by the related generic clocks
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:31 +0000 (15:58 +0100)]
clk: meson: remove obsolete comments
Over time things changes in CCF and issues have been fixed in meson
controllers.
Now, clk81 is decently modeled by read-only PLLs, a mux, a divider
and a gate. We can remove the FIXME comments related to clk81.
Also remove the comment about devm_clk_hw_register, as there is
apparently nothing wrong with it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:30 +0000 (15:58 +0100)]
clk: meson: only one loop index is necessary in probe
We don't need several loop index variables in the probe function
This is far from being critical but since we are doing a vast
rework of meson clock controllers, now is the time to lower the
entropy a bit
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:29 +0000 (15:58 +0100)]
clk: meson: use devm_of_clk_add_hw_provider
There is no remove callbacks in meson's clock controllers and
of_clk_del_provider is never called if of_clk_add_hw_provider has been
executed, introducing a potential memory leak.
Fixing this by the using the devm variant.
In reality, the leak would never happen since these controllers are
never unloaded once in use ... still, this is worth cleaning.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 12 Feb 2018 14:58:28 +0000 (15:58 +0100)]
clk: meson: use dev pointer where possible
The 'dev' pointer is directly available in gxbb and axg clock
controller, so consistently use it instead of going the through the
'pdev' pointer once in while
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Wed, 14 Feb 2018 13:43:39 +0000 (14:43 +0100)]
clk: divider: read-only divider can propagate rate change
When a divider clock has CLK_DIVIDER_READ_ONLY set, it means that the
register shall be left un-touched, but it does not mean the clock
should stop rate propagation if CLK_SET_RATE_PARENT is set
This is properly handled in qcom clk-regmap-divider but it was not in
the generic divider
To fix this situation, introduce a new helper function
divider_ro_round_rate, on the same model as divider_round_rate.
Fixes: e6d5e7d90be9 ("clk-divider: Fix READ_ONLY when divider > 1") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-By: David Lechner <david@lechnology.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Jerome Brunet [Wed, 14 Feb 2018 13:43:37 +0000 (14:43 +0100)]
clk: call the clock init() callback before any other ops callback
Some clocks may need to initialize things, whatever it is, before
being able to properly operate. Move the .init() call before any
other callback, such recalc_rate() or get_phase(), so the clock
is properly setup before being used.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Jerome Brunet [Wed, 14 Feb 2018 13:43:34 +0000 (14:43 +0100)]
clk: mux: add helper function for index/value translation
Add helper functions for the translation between parent index and
register value in the generic multiplexer function. The purpose of
this change is avoid duplicating the code in other clock providers,
using the same generic logic.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Jerome Brunet [Wed, 14 Feb 2018 13:43:33 +0000 (14:43 +0100)]
clk: divider: export clk_div_mask() helper
Export clk_div_mask() in clk-provider header so every clock providers
derived from the generic clock divider may share the definition instead
of redefining it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Jerome Brunet [Wed, 14 Feb 2018 13:43:35 +0000 (14:43 +0100)]
clk: fix determine rate error with pass-through clock
If we try to determine the rate of a pass-through clock (a clock which
does not implement .round_rate() nor .determine_rate()),
clk_core_round_rate_nolock() will directly forward the call to the
parent clock. In the particular case where the pass-through actually
does not have a parent, clk_core_round_rate_nolock() will directly
return 0 with the requested rate still set to the initial request
structure. This is interpreted as if the rate could be exactly achieved
while it actually cannot be adjusted.
This become a real problem when this particular pass-through clock is
the parent of a mux with the flag CLK_SET_RATE_PARENT set. The
pass-through clock will always report an exact match, get picked and
finally error when the rate is actually getting set.
This is fixed by setting the rate inside the req to 0 when core is NULL
in clk_core_round_rate_nolock() (same as in __clk_determine_rate() when
hw is NULL)
Fixes: 0f6cc2b8e94d ("clk: rework calls to round and determine rate callbacks") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Jerome Brunet [Wed, 14 Feb 2018 13:43:36 +0000 (14:43 +0100)]
clk: migrate the count of orphaned clocks at init
The orphan clocks reparents should migrate any existing count from the
orphan clock to its new acestor clocks, otherwise we may have
inconsistent counts in the tree and end-up with gated critical clocks
Assuming we have two clocks, A and B.
* Clock A has CLK_IS_CRITICAL flag set.
* Clock B is an ancestor of A which can gate. Clock B gate is left
enabled by the bootloader.
Step 1: Clock A is registered. Since it is a critical clock, it is
enabled. The clock being still an orphan, no parent are enabled.
Step 2: Clock B is registered and reparented to clock A (potentially
through several other clocks). We are now in situation where the enable
count of clock A is 1 while the enable count of its ancestors is 0, which
is not good.
Step 3: in lateinit, clk_disable_unused() is called, the enable_count of
clock B being 0, clock B is gated and and critical clock A actually gets
disabled.
This situation was found while adding fdiv_clk gates to the meson8b
platform. These clocks parent clk81 critical clock, which is the mother
of all peripheral clocks in this system. Because of the issue described
here, the system is crashing when clk_disable_unused() is called.
The situation is solved by reverting
commit f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration").
To avoid breaking again the situation described in this commit
description, enabling critical clock should be done before walking the
orphan list. This way, a parent critical clock may not be accidentally
disabled due to the CLK_OPS_PARENT_ENABLE mechanism.
Fixes: f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration") Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
Dmitry Osipenko [Wed, 10 Jan 2018 13:59:44 +0000 (16:59 +0300)]
clk: tegra: Specify VDE clock rate
Currently VDE clock rate is determined by clock config left from
bootloader, let's not rely on it and explicitly specify the clock
rate in the CCF driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
clk: samsung: exynos5420: Add more entries to EPLL rate table
Adding these EPLL output frequency entries allows to support all required
audio sample rates on the CODEC and the HDMI interface on Peach-Pit
Chromebook.
clk: samsung: exynos5420: Add CLK_SET_RATE_PARENT flag to mout_mau_epll_clk
This allows changing the EPLL output frequency through the audio subsystem
clock tree leaf clocks. This change is needed to support audio on the HDMI
interface on Peach-Pi(t) Chromebook.
It seems the cached core->phase isn't updated after the clk was
registered. So fix this issue by updating the core->phase if setting
phase successfully.
Two micro-controller clock output (MCO) pins are available:
MCO1 and MCO2.
For each output, it is possible to select a clock source.
The selected clock can be divided thanks to configurable
prescaler.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each peripheral requires a bus interface clock.
Some peripherals need also a dedicated clock for their communication
interface, this clock is generally asynchronous with respect to the bus
interface clock (peripheral clock), and is named kernel clock.
For each IP, Peripheral clock and Kernel are generally gating with same
gate. Also, Kernel clocks can share a same multiplexer.
This patch introduces a mechanism to manage a gate with several
clocks and to manage a shared multiplexer (mgate and mmux).
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds Kernel timers.
This patch adds timers kernel clock.
Timers are gather into two groups corresponding to the APB bus
they are attached to.
Each group has its own prescaler, managed in this patch.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch introduces the mechanism to probe stm32mp1 driver.
It also defines registers definition.
This patch also introduces the generic mechanism to register
a clock (a simple gate, divider and fixed factor).
All clocks will be defined in one table.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The RCC block is responsible of the management of the clock and reset
generation for the complete circuit.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Tegra210 has a hw bug which can cause IP blocks to lock up when ungating a
domain. The reason is that the logic responsible for resetting the memory
built-in self test mode can come up in an undefined state because its
clock is gated by a second level clock gate (SLCG). Work around this by
making sure the logic will get some clock edges by ensuring the relevant
clock is enabled and temporarily override the relevant SLCGs.
Unfortunately for some IP blocks, the control bits for overriding the
SLCGs are not in CAR, but in the IP block itself. This means we need to
map a few extra register banks in the clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Hector Martin <marcan@marcan.st> Tested-by: Andre Heider <a.heider@gmail.com> Tested-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
fixup mbist
To ensure writes to clock registers have properly propagated through the
clock control logic and state machines, we need to ensure the writes have
been posted in the registers and wait for 1us after that.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Hector Martin <marcan@marcan.st> Tested-by: Andre Heider <a.heider@gmail.com> Tested-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is needed by the memory built-in self test work around.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Hector Martin <marcan@marcan.st> Tested-by: Andre Heider <a.heider@gmail.com> Tested-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Tero Kristo [Tue, 12 Dec 2017 08:31:15 +0000 (10:31 +0200)]
clk: keystone: sci-clk: add support for dynamically probing clocks
Currently, the driver contains a large hints table for clocks that exist
on a device, however, it is possible to probe the clocks from the firmware
also. Add support for this, and drop the clock hints table support from
the driver completely. This causes the driver to send a few extra sci-clk
messages during boot, basically one extra for each device that exists on
the SoC; on K2G this is approx 80.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tero Kristo [Thu, 15 Feb 2018 07:50:02 +0000 (09:50 +0200)]
clk: ti: add support for clock latching to mux clocks
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the mux clock.
Tero Kristo [Thu, 15 Feb 2018 07:49:27 +0000 (09:49 +0200)]
clk: ti: add support for clock latching to divider clocks
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the divider clock.
Tero Kristo [Wed, 26 Jul 2017 13:47:28 +0000 (16:47 +0300)]
clk: ti: add generic support for clock latching
Certain clocks require latching to be done, so that the actual
settings get updated on the HW that generates the clock signal.
One example of such a clock is the dra76x GMAC DPLL H14 output,
which requires its divider settings to be latched when updated.
projects / thirdparty / kernel / linux.git / log
