From ea339205a94706d8b9170bbd89e8c1373df9a92f Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 8 Nov 2005 09:00:09 +0100 Subject: [PATCH] Updated PCI mapping for esd CPCI2DP board. Add support for error LED. Patch by Matthias Fuchs, 07 Nov 2005 --- CHANGELOG | 4 ++++ board/esd/cpci2dp/cpci2dp.c | 15 +++++++++------ include/configs/CPCI2DP.h | 9 +++++---- 3 files changed, 18 insertions(+), 10 deletions(-) diff --git a/CHANGELOG b/CHANGELOG index 5c6d68fff0..5747cb4be5 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,10 @@ Changes for U-Boot 1.1.4: ====================================================================== +* Updated PCI mapping for esd CPCI2DP board. + Add support for error LED. + Patch by Matthias Fuchs, 07 Nov 2005 + * Fix MPC85xx PCI support (pci_register_hose() before pci config access) Patch by Stefan Roese, 07 Nov 2005 diff --git a/board/esd/cpci2dp/cpci2dp.c b/board/esd/cpci2dp/cpci2dp.c index 727640e9b5..b463f0e389 100644 --- a/board/esd/cpci2dp/cpci2dp.c +++ b/board/esd/cpci2dp/cpci2dp.c @@ -31,14 +31,17 @@ int board_early_init_f (void) unsigned long cntrl0Reg; /* - * Setup GPIO pins (CS4 as GPIO) + * Setup GPIO pins (CS4+CS7 as GPIO) */ cntrl0Reg = mfdcr(cntrl0); - mtdcr(cntrl0, cntrl0Reg | 0x00800000); - - out32(GPIO0_OR, CFG_INTA_FAKE | CFG_EEPROM_WP); /* set output pins to high */ - out32(GPIO0_ODR, CFG_INTA_FAKE); /* INTA# is open drain */ - out32(GPIO0_TCR, CFG_INTA_FAKE | CFG_EEPROM_WP); /* setup for output */ + mtdcr(cntrl0, cntrl0Reg | 0x00900000); + + /* set output pins to high */ + out32(GPIO0_OR, CFG_INTA_FAKE | CFG_EEPROM_WP | CFG_PB_LED); + /* INTA# is open drain */ + out32(GPIO0_ODR, CFG_INTA_FAKE); + /* setup for output */ + out32(GPIO0_TCR, CFG_INTA_FAKE | CFG_EEPROM_WP); /* * IRQ 0-15 405GP internally generated; active high; level sensitive diff --git a/include/configs/CPCI2DP.h b/include/configs/CPCI2DP.h index 4a6a3f8515..756bb8ceac 100644 --- a/include/configs/CPCI2DP.h +++ b/include/configs/CPCI2DP.h @@ -146,9 +146,9 @@ #define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ #define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ #define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0xef600000 /* point to internal regs + PB0/1 */ +#define CFG_PCI_PTM2LA 0xef000000 /* point to internal regs + PB0/1 */ #define CFG_PCI_PTM2MS 0xff000001 /* 16MB, enable */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration @@ -237,11 +237,11 @@ /* Memory Bank 2 (PB0) initialization */ #define CFG_EBC_PB2AP 0x03004580 /* TWT=6,WBN=1,TH=2,RE=1,SOR=1 */ -#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ +#define CFG_EBC_PB2CR 0xEF018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ /* Memory Bank 3 (PB1) initialization */ #define CFG_EBC_PB3AP 0x03004580 /* TWT=6,WBN=1,TH=2,RE=1,SOR=1 */ -#define CFG_EBC_PB3CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */ +#define CFG_EBC_PB3CR 0xEF118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in data cache) @@ -258,6 +258,7 @@ * GPIO definitions */ #define CFG_EEPROM_WP (0x80000000 >> 13) /* GPIO13 */ +#define CFG_PB_LED (0x80000000 >> 16) /* GPIO16 */ #define CFG_INTA_FAKE (0x80000000 >> 23) /* GPIO23 */ /* -- 2.39.2