The call of unsubscribe_port() which manages the group count and
module refcount from delete_and_unsubscribe_port() looks racy; it's
not covered by the group list lock, and it's likely a cause of the
reported unbalance at port deletion. Let's move the call inside the
group list_mutex to plug the hole.
In the case of a normal sync update, the preparation of framebuffers (be
it calling drm_atomic_helper_prepare_planes() or doing setups with
drm_framebuffer_get()) are performed in the new_state and the respective
cleanups are performed in the old_state.
In the case of async updates, the preparation is also done in the
new_state but the cleanups are done in the new_state (because updates
are performed in place, i.e. in the current state).
The current code blocks async udpates when the fb is changed, turning
async updates into sync updates, slowing down cursor updates and
introducing regressions in igt tests with errors of type:
"CRITICAL: completed 97 cursor updated in a period of 30 flips, we
expect to complete approximately 15360 updates, with the threshold set
at 7680"
Fb changes in async updates were prevented to avoid the following scenario:
- Async update, oldfb = NULL, newfb = fb1, prepare fb1, cleanup fb1
- Async update, oldfb = fb1, newfb = fb2, prepare fb2, cleanup fb2
- Non-async commit, oldfb = fb2, newfb = fb1, prepare fb1, cleanup fb2 (wrong)
Where we have a single call to prepare fb2 but double cleanup call to fb2.
To solve the above problems, instead of blocking async fb changes, we
place the old framebuffer in the new_state object, so when the code
performs cleanups in the new_state it will cleanup the old_fb and we
will have the following scenario instead:
Sven reports:
Commit 1e07d63749 ("drm/nouveau: add kconfig option to turn off nouveau
legacy contexts. (v3)") has caused a build failure for me when I
actually tried that option (CONFIG_NOUVEAU_LEGACY_CTX_SUPPORT=n):
,----
| Kernel: arch/x86/boot/bzImage is ready (#1)
| Building modules, stage 2.
| MODPOST 290 modules
| ERROR: "drm_legacy_mmap" [drivers/gpu/drm/nouveau/nouveau.ko] undefined!
| scripts/Makefile.modpost:91: recipe for target '__modpost' failed
`----
Upstream does not have that problem, as commit bed2dd8421 ("drm/ttm:
Quick-test mmap offset in ttm_bo_mmap()") has removed the use of
drm_legacy_mmap from nouveau_ttm.c. Unfortunately that commit does not
apply in 5.1.9.
The ensuing discussion proposed a number of one-off patches, but no
solid agreement was made, so just revert the commit for now to get
people's systems building again.
Reported-by: Sven Joachim <svenjoac@gmx.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@redhat.com> Cc: Thomas Backlund <tmb@mageia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lots of people have reported issues with this patch, and as there does
not seem to be a fix going into Linus's kernel tree any time soon,
revert the commit in the stable trees so as to get people's machines
working properly again.
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com> Reported-by: Hans de Goede <hdegoede@redhat.com> Cc: Jeremy Cline <jeremy@jcline.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcpu_find_block_fit() guarantees that a fit is found within
PCPU_BITMAP_BLOCK_BITS. Iteration is used to determine the first fit as
it compares against the block's contig_hint. This can lead to
incorrectly scanning past the end of the bitmap. The behavior was okay
given the check after for bit_off >= end and the correctness of the
hints from pcpu_find_block_fit().
This patch fixes this by bounding the end offset by the number of bits
in a chunk.
Signed-off-by: Dennis Zhou <dennis@kernel.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The datasheet says the vconn MUST be off when we start toggling. The
tcpm.c state-machine is responsible to make sure vconn is off, but lets
add a WARN to catch any cases where vconn is not off for some reason.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During early system resume on Exynos5422 with performance counters enabled
the following kernel oops happens:
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1433 Comm: bash Tainted: G W 5.0.0-rc5-next-20190208-00023-gd5fb5a8a13e6-dirty #5480
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
...
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4451006a DAC: 00000051
Process bash (pid: 1433, stack limit = 0xb7e0e22f)
...
(reset_ctrl_regs) from [<c0112ad0>] (dbg_cpu_pm_notify+0x1c/0x24)
(dbg_cpu_pm_notify) from [<c014c840>] (notifier_call_chain+0x44/0x84)
(notifier_call_chain) from [<c014cbc0>] (__atomic_notifier_call_chain+0x7c/0x128)
(__atomic_notifier_call_chain) from [<c01ffaac>] (cpu_pm_notify+0x30/0x54)
(cpu_pm_notify) from [<c055116c>] (syscore_resume+0x98/0x3f4)
(syscore_resume) from [<c0189350>] (suspend_devices_and_enter+0x97c/0xe74)
(suspend_devices_and_enter) from [<c0189fb8>] (pm_suspend+0x770/0xc04)
(pm_suspend) from [<c0187740>] (state_store+0x6c/0xcc)
(state_store) from [<c09fa698>] (kobj_attr_store+0x14/0x20)
(kobj_attr_store) from [<c030159c>] (sysfs_kf_write+0x4c/0x50)
(sysfs_kf_write) from [<c0300620>] (kernfs_fop_write+0xfc/0x1e0)
(kernfs_fop_write) from [<c0282be8>] (__vfs_write+0x2c/0x160)
(__vfs_write) from [<c0282ea4>] (vfs_write+0xa4/0x16c)
(vfs_write) from [<c0283080>] (ksys_write+0x40/0x8c)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Undefined instruction is triggered during CP14 reset, because bits: #16
(Secure privileged invasive debug disabled) and #17 (Secure privileged
noninvasive debug disable) are set in DSCR. Those bits depend on SPNIDEN
and SPIDEN lines, which are provided by Secure JTAG hardware block. That
block in turn is powered from cluster 0 (big/Eagle), but the Exynos5422
boots on cluster 1 (LITTLE/KFC).
To fix this issue it is enough to turn on the power on the cluster 0 for
a while. This lets the Secure JTAG block to propagate the needed signals
to LITTLE/KFC cores and change their DSCR.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sysfs unexport in pwmchip_remove() is completely asymmetric
to what we do in pwmchip_add_with_polarity() and commit 0733424c9ba9
("pwm: Unexport children before chip removal") is a strong indication
that this was wrong to begin with. We should just move
pwmchip_sysfs_unexport() where it belongs, which is right after
pwmchip_sysfs_unexport_children(). In that case, we do not need
separate functions anymore either.
We also really want to remove sysfs irrespective of whether or not
the chip will be removed as a result of pwmchip_remove(). We can only
assume that the driver will be gone after that, so we shouldn't leave
any dangling sysfs files around.
This warning disappears if we move pwmchip_sysfs_unexport() to
the top of pwmchip_remove(), pwmchip_sysfs_unexport_children().
That way it is also outside of the pwm_lock section, which indeed
doesn't seem to be needed.
Moving the pwmchip_sysfs_export() call outside of that section also
seems fine and it'd be perfectly symmetric with pwmchip_remove() again.
So, this patch fixes them.
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
[shimoda: revise the commit log and code] Fixes: 76abbdde2d95 ("pwm: Add sysfs interface") Fixes: 0733424c9ba9 ("pwm: Unexport children before chip removal") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Hoan Nguyen An <na-hoan@jinso.co.jp> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PVDD_APIO_1V8 (LDO2) and PVDD_ABB_1V8 (LDO8) regulators were turned
off by Linux kernel as unused. However they supply critical parts of
SoC so they should be always on:
1. PVDD_APIO_1V8 supplies SYS pins (gpx[0-3], PSHOLD), HDMI level shift,
RTC, VDD1_12 (DRAM internal 1.8 V logic), pull-up for PMIC interrupt
lines, TTL/UARTR level shift, reset pins and SW-TACT1 button.
It also supplies unused blocks like VDDQ_SRAM (for SROM controller) and
VDDQ_GPIO (gpm7, gpy7).
The LDO2 cannot be turned off (S2MPS11 keeps it on anyway) so
marking it "always-on" only reflects its real status.
2. PVDD_ABB_1V8 supplies Adaptive Body Bias Generator for ARM cores,
memory and Mali (G3D).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It must be made sure that immediate mode is not already set, when
modifying shadow register value in ehrpwm_pwm_disable(). Otherwise
modifications to the action-qualifier continuous S/W force
register(AQSFRC) will be done in the active register.
This may happen when both channels are being disabled. In this case,
only the first channel state will be recorded as disabled in the shadow
register. Later, when enabling the first channel again, the second
channel would be enabled as well. Setting RLDCSF to zero, first, ensures
that the shadow register is updated as desired.
Fixes: 38dabd91ff0b ("pwm: tiehrpwm: Fix disabling of output of PWMs") Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
[vigneshr@ti.com: Improve commit message] Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts] Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We are currently assuming all GPIOs are non-wakeup capable GPIOs as we
not configuring the bank->non_wakeup_gpios like we used to earlier with
platform_data.
Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer
while considering that later patches may want to configure SoC specific
bank->non_wakeup_gpios for the GPIOs in wakeup domain.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Tero Kristo <t-kristo@ti.com> Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a sync bfq_queue has a higher weight than some other queue, and
remains temporarily empty while in service, then, to preserve the
bandwidth share of the queue, it is necessary to plug I/O dispatching
until a new request arrives for the queue. In addition, a timeout
needs to be set, to avoid waiting for ever if the process associated
with the queue has actually finished its I/O.
Even with the above timeout, the device is however not fed with new
I/O for a while, if the process has finished its I/O. If this happens
often, then throughput drops and latencies grow. For this reason, the
timeout is kept rather low: 8 ms is the current default.
Unfortunately, such a low value may cause, on the opposite end, a
violation of bandwidth guarantees for a process that happens to issue
new I/O too late. The higher the system load, the higher the
probability that this happens to some process. This is a problem in
scenarios where service guarantees matter more than throughput. One
important case are weight-raised queues, which need to be granted a
very high fraction of the bandwidth.
To address this issue, this commit lower-bounds the plugging timeout
for weight-raised queues to 20 ms. This simple change provides
relevant benefits. For example, on a PLEXTOR PX-256M5S, with which
gnome-terminal starts in 0.6 seconds if there is no other I/O in
progress, the same applications starts in
- 0.8 seconds, instead of 1.2 seconds, if ten files are being read
sequentially in parallel
- 1 second, instead of 2 seconds, if, in parallel, five files are
being read sequentially, and five more files are being written
sequentially
The MSI message address in the RC address space can be 64 bit. The
R-Car PCIe RC supports such a 64bit MSI message address as well.
The code currently uses virt_to_phys(__get_free_pages()) to obtain
a reserved page for the MSI message address, and the return value
of which can be a 64 bit physical address on 64 bit system.
However, the driver only programs PCIEMSIALR register with the bottom
32 bits of the virt_to_phys(__get_free_pages()) return value and does
not program the top 32 bits into PCIEMSIAUR, but rather programs the
PCIEMSIAUR register with 0x0. This worked fine on older 32 bit R-Car
SoCs, however may fail on new 64 bit R-Car SoCs.
Since from a PCIe controller perspective, an inbound MSI is a memory
write to a special address (in case of this controller, defined by
the value in PCIEMSIAUR:PCIEMSIALR), which triggers an interrupt, but
never hits the DRAM _and_ because allocation of an MSI by a PCIe card
driver obtains the MSI message address by reading PCIEMSIAUR:PCIEMSIALR
in rcar_msi_setup_irqs(), incorrectly programmed PCIEMSIAUR cannot
cause memory corruption or other issues.
There is however the possibility that if virt_to_phys(__get_free_pages())
returned address above the 32bit boundary _and_ PCIEMSIAUR was programmed
to 0x0 _and_ if the system had physical RAM at the address matching the
value of PCIEMSIALR, a PCIe card driver could allocate a buffer with a
physical address matching the value of PCIEMSIALR and a remote write to
such a buffer by a PCIe card would trigger a spurious MSI.
Fixes: e015f88c368d ("PCI: rcar: Add support for R-Car H3 to pcie-rcar") Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Phil Edworthy <phil.edworthy@renesas.com> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Call order on probe():
- max14656_hw_init() enables interrupts on the chip
- devm_request_irq() starts processing interrupts, isr
could be called immediately
- isr: schedules delayed work (irq_work)
- irq_work: calls power_supply_changed()
- devm_power_supply_register() registers the power supply
Depending on timing, it's possible that power_supply_changed()
is called on an unregistered power supply structure.
Fix by registering the power supply before requesting the irq.
Cc: Alexander Kurz <akurz@blala.de> Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The find_dlpar_node() helper returns a device node with its reference
incremented. Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.
Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths. Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Cc: Angus Ainslie (Purism) <angus@akkea.ca> Cc: Chris Healy <cphealy@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SL_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
The rk3288 SoC has two PWM implementations available, the "old"
implementation and the "new" one. You can switch between the two of
them by flipping a bit in the grf.
The "old" implementation is the default at chip power up but isn't the
one that's officially supposed to be used. ...and, in fact, the
driver that gets selected in Linux using the rk3288 device tree only
supports the "new" implementation.
Long ago I tried to get a switch to the right IP block landed in the
PWM driver (search for "rk3288: Switch to use the proper PWM IP") but
that got rejected. In the mean time the grf has grown a full-fledged
driver that already sets other random bits like this. That means we
can now get the fix landed.
For those wondering how things could have possibly worked for the last
4.5 years, folks have mostly been relying on the bootloader to set
this bit. ...but occasionally folks have pointed back to my old patch
series [1] in downstream kernels.
Experimentally it can be seen that going into deep sleep (specifically
setting PMU_CLR_DMA and PMU_CLR_BUS in RK3288_PMU_PWRMODE_CON1)
appears to fail unless "aclk_dmac1" is on. The failure is that the
system never signals that it made it into suspend on the GLOBAL_PWROFF
pin and it just hangs.
NOTE that it's confirmed that it's the actual suspend that fails, not
one of the earlier calls to read/write registers. Specifically if you
comment out the "PMU_GLOBAL_INT_DISABLE" setting in
rk3288_slp_mode_set() and then comment out the "cpu_do_idle()" call in
rockchip_lpmode_enter() then you can exercise the whole suspend path
without any crashing.
This is currently not a problem with suspend upstream because there is
no current way to exercise the deep suspend code. However, anyone
trying to make it work will run into this issue.
This was not a problem on shipping rk3288-based Chromebooks because
those devices all ran on an old kernel based on 3.14. On that kernel
"aclk_dmac1" appears to be left on all the time.
There are several ways to skin this problem.
A) We could add "aclk_dmac1" to the list of critical clocks and that
apperas to work, but presumably that wastes power.
B) We could keep a list of "struct clk" objects to enable at suspend
time in clk-rk3288.c and use the standard clock APIs.
C) We could make the rk3288-pmu driver keep a list of clocks to enable
at suspend time. Presumably this would require a dts and bindings
change.
D) We could just whack the clock on in the existing syscore suspend
function where we whack a bunch of other clocks. This is particularly
easy because we know for sure that the clock's only parent
("aclk_cpu") is a critical clock so we don't need to do anything more
than ungate it.
In this case I have chosen D) because it seemed like the least work,
but any of the other options would presumably also work fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/soc/mediatek/mtk-pmic-wrap.c:1358:6: error: variable 'rdata' is
used uninitialized whenever '||' condition is true
[-Werror,-Wsometimes-uninitialized]
If pwrap_write returns non-zero, pwrap_read will not be called to
initialize rdata, meaning that we will use some random uninitialized
stack value in our print statement. Zero initialize rdata in case this
happens.
hook_fault_code() is an ARM32 specific API for hooking into data abort.
AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As new transfer mechanisms are added to the EC codebase, they may
not support v2 of the EC protocol.
If the v3 initial handshake transfer fails, the kernel will try
and call cmd_xfer as a fallback. If v2 is not supported, cmd_xfer
will be NULL, and the code will end up causing a kernel panic.
Add a check for NULL before calling the transfer function, along
with a helpful comment explaining how one might end up in this
situation.
In pcibios_irq_init(), the PCI IRQ routing table 'pirq_table' is first
found through pirq_find_routing_table(). If the table is not found and
CONFIG_PCI_BIOS is defined, the table is then allocated in
pcibios_get_irq_routing_table() using kmalloc(). Later, if the I/O APIC is
used, this table is actually not used. In that case, the allocated table
is not freed, which is a memory leak.
Free the allocated table if it is not used.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
[bhelgaas: added Ingo's reviewed-by, since the only change since v1 was to
use the irq_routing_table local variable name he suggested] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
vfio_dev_present() which is the condition to
wait_event_interruptible_timeout(), will call vfio_group_get_device
and try to acquire the mutex group->device_lock.
wait_event_interruptible_timeout() will set the state of the current
task to TASK_INTERRUPTIBLE, before doing the condition check. This
means that we will try to acquire the mutex while already in a
sleeping state. The scheduler warns us by giving the following
warning:
[ 4050.264464] ------------[ cut here ]------------
[ 4050.264508] do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000b33c00e2>] prepare_to_wait_event+0x14a/0x188
[ 4050.264529] WARNING: CPU: 12 PID: 35924 at kernel/sched/core.c:6112 __might_sleep+0x76/0x90
....
A fuzzer recently triggered lockdep warnings about potential sb_writers
deadlocks caused by fh_want_write().
Looks like we aren't careful to pair each fh_want_write() with an
fh_drop_write().
It's not normally a problem since fh_put() will call fh_drop_write() for
us. And was OK for NFSv3 where we'd do one operation that might call
fh_want_write(), and then put the filehandle.
But an NFSv4 protocol fuzzer can do weird things like call unlink twice
in a compound, and then we get into trouble.
I'm a little worried about this approach of just leaving everything to
fh_put(). But I think there are probably a lot of
fh_want_write()/fh_drop_write() imbalances so for now I think we need it
to be more forgiving.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
FUSE filesystem server and kernel client negotiate during initialization
phase, what should be the maximum write size the client will ever issue.
Correspondingly the filesystem server then queues sys_read calls to read
requests with buffer capacity large enough to carry request header + that
max_write bytes. A filesystem server is free to set its max_write in
anywhere in the range between [1*page, fc->max_pages*page]. In particular
go-fuse[2] sets max_write by default as 64K, wheres default fc->max_pages
corresponds to 128K. Libfuse also allows users to configure max_write, but
by default presets it to possible maximum.
If max_write is < fc->max_pages*page, and in NOTIFY_RETRIEVE handler we
allow to retrieve more than max_write bytes, corresponding prepared
NOTIFY_REPLY will be thrown away by fuse_dev_do_read, because the
filesystem server, in full correspondence with server/client contract, will
be only queuing sys_read with ~max_write buffer capacity, and
fuse_dev_do_read throws away requests that cannot fit into server request
buffer. In turn the filesystem server could get stuck waiting indefinitely
for NOTIFY_REPLY since NOTIFY_RETRIEVE handler returned OK which is
understood by clients as that NOTIFY_REPLY was queued and will be sent
back.
Cap requested size to negotiate max_write to avoid the problem. This
aligns with the way NOTIFY_RETRIEVE handler works, which already
unconditionally caps requested retrieve size to fuse_conn->max_pages. This
way it should not hurt NOTIFY_RETRIEVE semantic if we return less data than
was originally requested.
Please see [1] for context where the problem of stuck filesystem was hit
for real, how the situation was traced and for more involving patch that
did not make it into the tree.
When the bit_offset in the cell is zero, the pointer to the msb will
not be properly initialized (ie, will still be pointing to the first
byte in the buffer).
This being the case, if there are bits to clear in the msb, those will
be left untouched while the mask will incorrectly clear bit positions
on the first byte.
This commit also makes sure that any byte unused in the cell is
cleared.
Currently the IRQ handler in HD-audio controller driver is registered
before the chip initialization. That is, we have some window opened
between the azx_acquire_irq() call and the CORB/RIRB setup. If an
interrupt is triggered in this small window, the IRQ handler may
access to the uninitialized RIRB buffer, which leads to a NULL
dereference Oops.
This is usually no big problem since most of Intel chips do register
the IRQ via MSI, and we've already fixed the order of the IRQ
enablement and the CORB/RIRB setup in the former commit b61749a89f82
("sound: enable interrupt after dma buffer initialization"), hence the
IRQ won't be triggered in that room. However, some platforms use a
shared IRQ, and this may allow the IRQ trigger by another source.
Another possibility is the kdump environment: a stale interrupt might
be present in there, the IRQ handler can be falsely triggered as well.
For covering this small race, let's move the azx_acquire_irq() call
after hda_intel_init_chip() call. Although this is a bit radical
change, it can cover more widely than checking the CORB/RIRB setup
locally in the callee side.
Just like IO queues, the admin queue also will not be restarted after a
controller shutdown. Unquiesce this queue so that we do not block
request dispatch on a permanently disabled controller.
Reported-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 834b90519925 ("misc: pci_endpoint_test: Add support for
PCI_ENDPOINT_TEST regs to be mapped to any BAR") while adding
test_reg_bar in order to map PCI_ENDPOINT_TEST regs to be mapped to any
BAR failed to update test_reg_bar in pci_endpoint_test, resulting in
test_reg_bar having invalid value when used outside probe.
Fix it.
Fixes: 834b90519925 ("misc: pci_endpoint_test: Add support for PCI_ENDPOINT_TEST regs to be mapped to any BAR") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The intel_iommu_gfx_mapped flag is exported by the Intel
IOMMU driver to indicate whether an IOMMU is used for the
graphic device. In a virtualized IOMMU environment (e.g.
QEMU), an include-all IOMMU is used for graphic device.
This flag is found to be clear even the IOMMU is used.
Cc: Ashok Raj <ashok.raj@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: Kevin Tian <kevin.tian@intel.com> Reported-by: Zhenyu Wang <zhenyuw@linux.intel.com> Fixes: c0771df8d5297 ("intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.") Suggested-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
With holding queue's kobject refcount, it is safe for driver
to schedule requeue. However, blk_mq_kick_requeue_list() may
be called after blk_sync_queue() is done because of concurrent
requeue activities, then requeue work may not be completed when
freeing queue, and kernel oops is triggered.
So moving the cancel of requeue_work into blk_mq_release() for
avoiding race between requeue and freeing queue.
Cc: Dongli Zhang <dongli.zhang@oracle.com> Cc: James Smart <james.smart@broadcom.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: linux-scsi@vger.kernel.org, Cc: Martin K . Petersen <martin.petersen@oracle.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>, Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: James Smart <james.smart@broadcom.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
CONFIG_WATCHDOG_PRETIMEOUT_GOV build symbol adds watchdog_pretimeout.o
object to watchdog.o, the latter is compiled only if CONFIG_WATCHDOG_CORE
is selected, so it rightfully makes sense to add it as a dependency.
The change fixes the next compilation errors, if CONFIG_WATCHDOG_CORE=n
and CONFIG_WATCHDOG_PRETIMEOUT_GOV=y are selected:
drivers/watchdog/pretimeout_noop.o: In function `watchdog_gov_noop_register':
drivers/watchdog/pretimeout_noop.c:35: undefined reference to `watchdog_register_governor'
drivers/watchdog/pretimeout_noop.o: In function `watchdog_gov_noop_unregister':
drivers/watchdog/pretimeout_noop.c:40: undefined reference to `watchdog_unregister_governor'
drivers/watchdog/pretimeout_panic.o: In function `watchdog_gov_panic_register':
drivers/watchdog/pretimeout_panic.c:35: undefined reference to `watchdog_register_governor'
drivers/watchdog/pretimeout_panic.o: In function `watchdog_gov_panic_unregister':
drivers/watchdog/pretimeout_panic.c:40: undefined reference to `watchdog_unregister_governor'
The documentated behavior is: if max_hw_heartbeat_ms is implemented, the
minimum of the set_timeout argument and max_hw_heartbeat_ms should be used.
This patch implements this behavior.
Previously only the first 7bits were used and the input argument was
returned.
The IRQ handler, mmci_irq(), loops until all status bits have been cleared.
However, the status bit signaling busy in variant->busy_detect_flag, may be
set even if busy detection isn't monitored for the current request.
This may be the case for the CMD11 when switching the I/O voltage, which
leads to that mmci_irq() busy loops in IRQ context. Fix this problem, by
clearing the status bit for busy, before continuing to validate the
condition for the loop. This is safe, because the busy status detection has
already been taken care of by mmci_cmd_irq().
random: get_random_bytes called from init_oops_id+0x27/0x34 with crng_init=0
---[ end trace 00173d0117a88acb ]---
Calibrating delay loop... 6941.90 BogoMIPS (lpj=34709504)
Signed-off-by: Maciej Żenczykowski <maze@google.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: linux-um@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
In configfs_register_group(), if create_default_group() failed, we
forget to unlink the group. It will left a invalid item in the parent list,
which may trigger the use-after-free issue seen below:
BUG: KASAN: use-after-free in __list_add_valid+0xd4/0xe0 lib/list_debug.c:26
Read of size 8 at addr ffff8881ef61ae20 by task syz-executor.0/5996
Memory state around the buggy address: ffff8881ef61ad00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8881ef61ad80: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
>ffff8881ef61ae00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881ef61ae80: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff8881ef61af00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 5cf6a51e6062 ("configfs: allow dynamic group creation") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In free_percpu() we sometimes call pcpu_schedule_balance_work() to
queue a work item (which does a wakeup) while holding pcpu_lock.
This creates an unnecessary lock dependency between pcpu_lock and
the scheduler's pi_lock. There are other places where we call
pcpu_schedule_balance_work() without hold pcpu_lock, and this case
doesn't need to be different.
Moving the call outside the lock prevents the following lockdep splat
when running tools/testing/selftests/bpf/{test_maps,test_progs} in
sequence with lockdep enabled:
======================================================
WARNING: possible circular locking dependency detected
5.1.0-dbg-DEV #1 Not tainted
------------------------------------------------------
kworker/23:255/18872 is trying to acquire lock: 000000000bc79290 (&(&pool->lock)->rlock){-.-.}, at: __queue_work+0xb2/0x520
but task is already holding lock: 00000000e3e7a6aa (pcpu_lock){..-.}, at: free_percpu+0x36/0x260
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
- Overview
When mounting the attached crafted image and running program, following errors are reported.
Additionally, it hangs on sync after running program.
The image is intentionally fuzzed from a normal f2fs image for testing.
Compile options for F2FS are as follows.
CONFIG_F2FS_FS=y
CONFIG_F2FS_STAT_FS=y
CONFIG_F2FS_FS_XATTR=y
CONFIG_F2FS_FS_POSIX_ACL=y
CONFIG_F2FS_CHECK_FS=y
- Reproduces
cc poc_13.c
mkdir test
mount -t f2fs tmp.img test
cp a.out test
cd test
sudo ./a.out
sync
sit.vblocks and sum valid block count in sit.valid_map may be
inconsistent, segment w/ zero vblocks will be treated as free
segment, while allocating in free segment, we may allocate a
free block, if its bitmap is valid previously, it can cause
kernel crash due to bitmap verification failure.
Anyway, to avoid further serious metadata inconsistence and
corruption, it is necessary and worth to detect SIT
inconsistence. So let's enable check_block_count() to verify
vblocks and valid_map all the time rather than do it only
CONFIG_F2FS_CHECK_FS is enabled.
During inode loading, __recover_inline_status() can recovery inode status
and set inode dirty, once we failed in following process, it will fail
the check in f2fs_evict_inode, result in trigger BUG_ON().
Let's clear dirty inode in error path of f2fs_iget() to avoid panic.
- Overview
When mounting the attached crafted image, following errors are reported.
Additionally, it hangs on sync after trying to mount it.
The image is intentionally fuzzed from a normal f2fs image for testing.
Compile options for F2FS are as follows.
CONFIG_F2FS_FS=y
CONFIG_F2FS_STAT_FS=y
CONFIG_F2FS_FS_XATTR=y
CONFIG_F2FS_FS_POSIX_ACL=y
CONFIG_F2FS_CHECK_FS=y
- Reproduces
mkdir test
mount -t f2fs tmp.img test
sync
During recovery, if ofs_of_node is inconsistent in between recovered
node page and original checkpointed node page, let's just fail recovery
instead of making kernel panic.
The ADJ_TAI adjtimex mode sets the TAI-UTC offset of the system clock.
It is typically set by NTP/PTP implementations and it is automatically
updated by the kernel on leap seconds. The initial value is zero (which
applications may interpret as unknown), but this value cannot be set by
adjtimex. This limitation seems to go back to the original "nanokernel"
implementation by David Mills.
Change the ADJ_TAI check to accept zero as a valid TAI-UTC offset in
order to allow setting it back to the initial value.
Fixes: 153b5d054ac2 ("ntp: support for TAI") Suggested-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Link: https://lkml.kernel.org/r/20190417084833.7401-1-mlichvar@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Holding the spin-lock for all of the code in meson_pwm_apply() can
result in a "BUG: scheduling while atomic". This can happen because
clk_get_rate() (which is called from meson_pwm_calc()) may sleep.
Only hold the spin-lock when modifying registers to solve this.
The reason why we need a spin-lock in the driver is because the
REG_MISC_AB register is shared between the two channels provided by one
PWM controller. The only functions where REG_MISC_AB is modified are
meson_pwm_enable() and meson_pwm_disable() so the register reads/writes
in there need to be protected by the spin-lock.
The original code also used the spin-lock to protect the values in
struct meson_pwm_channel. This could be necessary if two consumers can
use the same PWM channel. However, PWM core doesn't allow this so we
don't need to protect the values in struct meson_pwm_channel with a
lock.
Fixes: 211ed630753d2f ("pwm: Add support for Meson PWM Controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ignore flag is set on fake jumps in order to keep
add_jump_destinations() from setting their jump_dest, since it already
got set when the fake jump was created.
But using the ignore flag is a bit of a hack. It's normally used to
skip validation of an instruction, which doesn't really make sense for
fake jumps.
Also, after the next patch, using the ignore flag for fake jumps can
trigger a false "why am I validating an ignored function?" warning.
Instead just add an explicit check in add_jump_destinations() to skip
fake jumps.
The driver currently sets register 0xfb (Low Refresh Rate) based on the
value of mode->vrefresh. Firstly, this field is specified to be in Hz,
but the magic numbers used by the code are Hz * 1000. This essentially
leads to the low refresh rate always being set to 0x01, since the
vrefresh value will always be less than 24000. Fix the magic numbers to
be in Hz.
Secondly, according to the comment in drm_modes.h, the field is not
supposed to be used in a functional way anyway. Instead, use the helper
function drm_mode_vrefresh().
Fixes: 9c8af882bf12 ("drm: Add adv7511 encoder driver") Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190424132210.26338-1-matt.redfearn@thinci.com Signed-off-by: Sasha Levin <sashal@kernel.org>
583feb08e7f7 ("perf/x86/intel: Fix handling of wakeup_events for multi-entry PEBS")
The original patch prevented using multi-entry PEBS when wakeup_events != 0.
However given that wakeup_events is part of a union with wakeup_watermark, it
means that in watermark mode, PEBS multi-entry is also disabled which is not the
intent. This patch fixes this by checking is watermark mode is enabled.
I noticed that we can get a -EREMOTEIO errors on at least omap4 duovero:
twl6040 0-004b: Failed to write 2d = 19: -121
And then any following register access will produce errors.
There 2d offset above is register ACCCTL that gets written on twl6040
powerup. With error checking added to the related regcache_sync() call,
the -EREMOTEIO error is reproducable on twl6040 powerup at least
duovero.
To fix the error, we need to wait until twl6040 is accessible after the
powerup. Based on tests on omap4 duovero, we need to wait over 8ms after
powerup before register write will complete without failures. Let's also
make sure we warn about possible errors too.
Note that we have twl6040_patch[] reg_sequence with the ACCCTL register
configuration and regcache_sync() will write the new value to ACCCTL.
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Where possible, we want the failsafe link configuration (one which won't
hang the OR during modeset because of not enough bandwidth for the mode)
to also be supported by the sink.
This prevents "link rate unsupported by sink" messages when link training
fails.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid interrupt storm, set the device in reset state
before bringing out the device from reset state.
Changelog v2:
- correct the subject line by adding "mfd: "
Signed-off-by: Binbin Wu <binbin.wu@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: spi:tps65912
After this patch:
modinfo drivers/mfd/tps65912-spi.ko | grep alias
alias: of:N*T*Cti,tps65912C*
alias: of:N*T*Cti,tps65912
alias: spi:tps65912
Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Daniel Gomez <dagmcr@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently IRQ remains enabled after .remove, later if device is probed,
IRQ is requested before .thermal_init, this may cause IRQ function be
called before device is initialized.
this patch disables interrupt in .remove, to ensure irq function
only be called after device is fully initialized.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While validating new map we require the @start_data to be strictly less
than @end_data, which is fine for regular applications (this is why this
nit didn't trigger for that long). These members are set from executable
loaders such as elf handers, still it is pretty valid to have a loadable
data section with zero size in file, in such case the start_data is equal
to end_data once kernel loader finishes.
As a result when we're trying to restore such programs the procedure fails
and the kernel returns -EINVAL. From the image dump of a program:
"cat /proc/slab_allocators" could hang forever on SMP machines with
kmemleak or object debugging enabled due to other CPUs running do_drain()
will keep making kmemleak_object or debug_objects_cache dirty and unable
to escape the first loop in leaks_show(),
do {
set_store_user_clean(cachep);
drain_cpu_caches(cachep);
...
One approach is to check cachep->name and skip both kmemleak_object and
debug_objects_cache in leaks_show(). The other is to set store_user_clean
after drain_cpu_caches() which leaves a small window between
drain_cpu_caches() and set_store_user_clean() where per-CPU caches could
be dirty again lead to slightly wrong information has been stored but
could also speed up things significantly which sounds like a good
compromise. For example,
If not find zero bit in find_next_zero_bit(), it will return the size
parameter passed in, so the start bit should be compared with bitmap_maxno
rather than cma->count. Although getting maxchunk is working fine due to
zero value of order_per_bit currently, the operation will be stuck if
order_per_bit is set as non-zero.
Link: http://lkml.kernel.org/r/20190319092734.276-1-zbestahu@gmail.com Signed-off-by: Yue Hu <huyue2@yulong.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Joe Perches <joe@perches.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Safonov <d.safonov@partner.samsung.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently one bit in cma bitmap represents number of pages rather than
one page, cma->count means cma size in pages. So to find available pages
via find_next_zero_bit()/find_next_bit() we should use cma size not in
pages but in bits although current free pages number is correct due to
zero value of order_per_bit. Once order_per_bit is changed the bitmap
status will be incorrect.
The size input in cma_debug_show_areas() is not correct. It will
affect the available pages at some position to debug the failure issue.
This is an example with order_per_bit = 1
Before this change:
[ 4.120060] cma: number of available pages: 1@93+4@108+7@121+7@137+7@153+7@169+7@185+7@201+3@213+3@221+3@229+3@237+3@245+3@253+3@261+3@269+3@277+3@285+3@293+3@301+3@309+3@317+3@325+19@333+15@369+512@512=> 638 free of 1024 total pages
After this change:
[ 4.143234] cma: number of available pages: 2@93+8@108+14@121+14@137+14@153+14@169+14@185+14@201+6@213+6@221+6@229+6@237+6@245+6@253+6@261+6@269+6@277+6@285+6@293+6@301+6@309+6@317+6@325+38@333+30@369=> 252 free of 1024 total pages
Obviously the bitmap status before is incorrect.
Link: http://lkml.kernel.org/r/20190320060829.9144-1-zbestahu@gmail.com Signed-off-by: Yue Hu <huyue2@yulong.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Laura Abbott <labbott@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
f022d8cb7ec7 ("mm: cma: Don't crash on allocation if CMA area can't be
activated") fixes the crash issue when activation fails via setting
cma->count as 0, same logic exists if bitmap allocation fails.
Link: http://lkml.kernel.org/r/20190325081309.6004-1-zbestahu@gmail.com Signed-off-by: Yue Hu <huyue2@yulong.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
342332e6a925 ("mm/page_alloc.c: introduce kernelcore=mirror option") and
later patches rewrote the calculation of node spanned pages.
e506b99696a2 ("mem-hotplug: fix node spanned pages when we have a movable
node"), but the current code still has problems,
When we have a node with only zone_movable and the node id is not zero,
the size of node spanned pages is double added.
That's because we have an empty normal zone, and zone_start_pfn or
zone_end_pfn is not between arch_zone_lowest_possible_pfn and
arch_zone_highest_possible_pfn, so we need to use clamp to constrain the
range just like the commit <96e907d13602> (bootmem: Reimplement
__absent_pages_in_range() using for_each_mem_pfn_range()).
e.g.
Zone ranges:
DMA [mem 0x0000000000001000-0x0000000000ffffff]
DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
Normal [mem 0x0000000100000000-0x000000023fffffff]
Movable zone start for each node
Node 0: 0x0000000100000000
Node 1: 0x0000000140000000
Early memory node ranges
node 0: [mem 0x0000000000001000-0x000000000009efff]
node 0: [mem 0x0000000000100000-0x00000000bffdffff]
node 0: [mem 0x0000000100000000-0x000000013fffffff]
node 1: [mem 0x0000000140000000-0x000000023fffffff]
When a huge page is allocated, PagePrivate() is set if the allocation
consumed a reservation. When freeing a huge page, PagePrivate is checked.
If set, it indicates the reservation should be restored. PagePrivate
being set at free huge page time mostly happens on error paths.
When huge page reservations are created, a check is made to determine if
the mapping is associated with an explicitly mounted filesystem. If so,
pages are also reserved within the filesystem. The default action when
freeing a huge page is to decrement the usage count in any associated
explicitly mounted filesystem. However, if the reservation is to be
restored the reservation/use count within the filesystem should not be
decrementd. Otherwise, a subsequent page allocation and free for the same
mapping location will cause the file filesystem usage to go 'negative'.
Filesystem Size Used Avail Use% Mounted on
nodev 4.0G -4.0M 4.1G - /opt/hugepool
To fix, when freeing a huge page do not adjust filesystem usage if
PagePrivate() is set to indicate the reservation should be restored.
I did not cc stable as the problem has been around since reserves were
added to hugetlbfs and nobody has noticed.
Link: http://lkml.kernel.org/r/20190328234704.27083-2-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid random config build issue, select mmu notifier when HMM is
selected. In any cases when HMM get selected it will be by users that
will also wants the mmu notifier.
Link: http://lkml.kernel.org/r/20190403193318.16478-2-jglisse@redhat.com Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Acked-by: Balbir Singh <bsingharora@gmail.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Souptick Joarder <jrdr.linux@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "compiler: allow all arches to enable
CONFIG_OPTIMIZE_INLINING", v3.
This patch (of 11):
When function tracing for IPIs is enabled, we get a warning for an
overflow of the ipi_types array with the IPI_CPU_BACKTRACE type as
triggered by raise_nmi():
arch/arm/kernel/smp.c: In function 'raise_nmi':
arch/arm/kernel/smp.c:489:2: error: array subscript is above array bounds [-Werror=array-bounds]
trace_ipi_raise(target, ipi_types[ipinr]);
This is a correct warning as we actually overflow the array here.
This patch raise_nmi() to call __smp_cross_call() instead of
smp_cross_call(), to avoid calling into ftrace. For clarification, I'm
also adding a two new code comments describing how this one is special.
The warning appears to have shown up after commit e7273ff49acf ("ARM:
8488/1: Make IPI_CPU_BACKTRACE a "non-secure" SGI"), which changed the
number assignment from '15' to '8', but as far as I can tell has existed
since the IPI tracepoints were first introduced. If we decide to
backport this patch to stable kernels, we probably need to backport e7273ff49acf as well.
[yamada.masahiro@socionext.com: rebase on v5.1-rc1] Link: http://lkml.kernel.org/r/20190423034959.13525-2-yamada.masahiro@socionext.com Fixes: e7273ff49acf ("ARM: 8488/1: Make IPI_CPU_BACKTRACE a "non-secure" SGI") Fixes: 365ec7b17327 ("ARM: add IPI tracepoints") # v3.17 Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Mathieu Malaterre <malat@debian.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Stefan Agner <stefan@agner.ch> Cc: Boris Brezillon <bbrezillon@kernel.org> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Richard Weinberger <richard@nod.at> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Borislav Petkov <bp@suse.de> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
msgctl10 of ltp triggers the following lockup When CONFIG_KASAN is
enabled on large memory SMP systems, the pages initialization can take a
long time, if msgctl10 requests a huge block memory, and it will block
rcu scheduler, so release cpu actively.
After adding schedule() in free_msg, free_msg can not be called when
holding spinlock, so adding msg to a tmp list, and free it out of
spinlock
Davidlohr said:
"So after releasing the lock, the msg rbtree/list is empty and new
calls will not see those in the newly populated tmp_msg list, and
therefore they cannot access the delayed msg freeing pointers, which
is good. Also the fact that the node_cache is now freed before the
actual messages seems to be harmless as this is wanted for
msg_insert() avoiding GFP_ATOMIC allocations, and after releasing the
info->lock the thing is freed anyway so it should not change things"
Currently when userspace gives us a values that overflow e.g. file-max
and other callers of __do_proc_doulongvec_minmax() we simply ignore the
new value and leave the current value untouched.
This can be problematic as it gives the illusion that the limit has
indeed be bumped when in fact it failed. This commit makes sure to
return EINVAL when an overflow is detected. Please note that this is a
userspace facing change.
Link: http://lkml.kernel.org/r/20190210203943.8227-4-christian@brauner.io Signed-off-by: Christian Brauner <christian@brauner.io> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Waiman Long <longman@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
fsync() needs to make sure the data & meta-data of file are persistent
after the return of fsync(), even when a power-failure occurs later. In
the case of fat-fs, the FAT belongs to the meta-data of file, so we need
to issue a flush after the writeback of FAT instead before.
Also bail out early when any stage of fsync fails.
Link: http://lkml.kernel.org/r/20190409030158.136316-1-houtao1@huawei.com Signed-off-by: Hou Tao <houtao1@huawei.com> Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return type for get_regs_len in struct ethtool_ops is int,
the hns3 driver may return error when failing to get the regs
len by sending cmd to firmware.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define __ipv4_neigh_lookup_noref to return NULL when CONFIG_INET is disabled.
Fixes: 4b2a2bfeb3f0 ("neighbor: Call __ipv4_neigh_lookup_noref in neigh_xmit") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from commit 9c225f2655e3 ("vfs: atomic f_pos accesses as per
POSIX") files opened even via nonseekable_open gate read and write via lock
and do not allow them to be run simultaneously. This can create read vs
write deadlock if a filesystem is trying to implement a socket-like file
which is intended to be simultaneously used for both read and write from
filesystem client. See commit 10dce8af3422 ("fs: stream_open - opener for
stream-like files so that read and write can run simultaneously without
deadlock") for details and e.g. commit 581d21a2d02a ("xenbus: fix deadlock
on writes to /proc/xen/xenbus") for a similar deadlock example on
/proc/xen/xenbus.
To avoid such deadlock it was tempting to adjust fuse_finish_open to use
stream_open instead of nonseekable_open on just FOPEN_NONSEEKABLE flags,
but grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE,
and in particular GVFS which actually uses offset in its read and write
handlers
so if we would do such a change it will break a real user.
Add another flag (FOPEN_STREAM) for filesystem servers to indicate that the
opened handler is having stream-like semantics; does not use file position
and thus the kernel is free to issue simultaneous read and write request on
opened file handle.
This patch together with stream_open() should be added to stable kernels
starting from v3.14+. This will allow to patch OSSPD and other FUSE
filesystems that provide stream-like files to return FOPEN_STREAM |
FOPEN_NONSEEKABLE in open handler and this way avoid the deadlock on all
kernel versions. This should work because fuse_finish_open ignores unknown
open flags returned from a filesystem and so passing FOPEN_STREAM to a
kernel that is not aware of this flag cannot hurt. In turn the kernel that
is not aware of FOPEN_STREAM will be < v3.14 where just FOPEN_NONSEEKABLE
is sufficient to implement streams without read vs write deadlock.
Commit 9c225f2655e3 ("vfs: atomic f_pos accesses as per POSIX") added
locking for file.f_pos access and in particular made concurrent read and
write not possible - now both those functions take f_pos lock for the
whole run, and so if e.g. a read is blocked waiting for data, write will
deadlock waiting for that read to complete.
This caused regression for stream-like files where previously read and
write could run simultaneously, but after that patch could not do so
anymore. See e.g. commit 581d21a2d02a ("xenbus: fix deadlock on writes
to /proc/xen/xenbus") which fixes such regression for particular case of
/proc/xen/xenbus.
The patch that added f_pos lock in 2014 did so to guarantee POSIX thread
safety for read/write/lseek and added the locking to file descriptors of
all regular files. In 2014 that thread-safety problem was not new as it
was already discussed earlier in 2006.
However even though 2006'th version of Linus's patch was adding f_pos
locking "only for files that are marked seekable with FMODE_LSEEK (thus
avoiding the stream-like objects like pipes and sockets)", the 2014
version - the one that actually made it into the tree as 9c225f2655e3 -
is doing so irregardless of whether a file is seekable or not.
The reason that it did so is, probably, that there are many files that
are marked non-seekable, but e.g. their read implementation actually
depends on knowing current position to correctly handle the read. Some
examples:
Despite that, many nonseekable_open users implement read and write with
pure stream semantics - they don't depend on passed ppos at all. And for
those cases where read could wait for something inside, it creates a
situation similar to xenbus - the write could be never made to go until
read is done, and read is waiting for some, potentially external, event,
for potentially unbounded time -> deadlock.
Besides xenbus, there are 14 such places in the kernel that I've found
with semantic patch (see below):
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write()
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write()
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write()
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write()
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write()
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write()
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write()
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write()
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write()
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write()
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write()
drivers/input/misc/uinput.c:400:1-17: ERROR: uinput_fops: .read() can deadlock .write()
drivers/infiniband/core/user_mad.c:985:7-23: ERROR: umad_fops: .read() can deadlock .write()
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write()
In addition to the cases above another regression caused by f_pos
locking is that now FUSE filesystems that implement open with
FOPEN_NONSEEKABLE flag, can no longer implement bidirectional
stream-like files - for the same reason as above e.g. read can deadlock
write locking on file.f_pos in the kernel.
FUSE's FOPEN_NONSEEKABLE was added in 2008 in a7c1b990f715 ("fuse:
implement nonseekable open") to support OSSPD. OSSPD implements /dev/dsp
in userspace with FOPEN_NONSEEKABLE flag, with corresponding read and
write routines not depending on current position at all, and with both
read and write being potentially blocking operations:
Corresponding libfuse example/test also describes FOPEN_NONSEEKABLE as
"somewhat pipe-like files ..." with read handler not using offset.
However that test implements only read without write and cannot exercise
the deadlock scenario:
I've actually hit the read vs write deadlock for real while implementing
my FUSE filesystem where there is /head/watch file, for which open
creates separate bidirectional socket-like stream in between filesystem
and its user with both read and write being later performed
simultaneously. And there it is semantically not easy to split the
stream into two separate read-only and write-only channels:
1. We can't change nonseekable_open to include &~FMODE_ATOMIC_POS -
doing so would break many in-kernel nonseekable_open users which
actually use ppos in read/write handlers.
2. Add stream_open() to kernel to open stream-like non-seekable file
descriptors. Read and write on such file descriptors would never use
nor change ppos. And with that property on stream-like files read and
write will be running without taking f_pos lock - i.e. read and write
could be running simultaneously.
3. With semantic patch search and convert to stream_open all in-kernel
nonseekable_open users for which read and write actually do not
depend on ppos and where there is no other methods in file_operations
which assume @offset access.
4. Add FOPEN_STREAM to fs/fuse/ and open in-kernel file-descriptors via
steam_open if that bit is present in filesystem open reply.
It was tempting to change fs/fuse/ open handler to use stream_open
instead of nonseekable_open on just FOPEN_NONSEEKABLE flags, but
grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE,
and in particular GVFS which actually uses offset in its read and
write handlers
so if we would do such a change it will break a real user.
5. Add stream_open and FOPEN_STREAM handling to stable kernels starting
from v3.14+ (the kernel where 9c225f2655 first appeared).
This will allow to patch OSSPD and other FUSE filesystems that
provide stream-like files to return FOPEN_STREAM | FOPEN_NONSEEKABLE
in their open handler and this way avoid the deadlock on all kernel
versions. This should work because fs/fuse/ ignores unknown open
flags returned from a filesystem and so passing FOPEN_STREAM to a
kernel that is not aware of this flag cannot hurt. In turn the kernel
that is not aware of FOPEN_STREAM will be < v3.14 where just
FOPEN_NONSEEKABLE is sufficient to implement streams without read vs
write deadlock.
This patch adds stream_open, converts /proc/xen/xenbus to it and adds
semantic patch to automatically locate in-kernel places that are either
required to be converted due to read vs write deadlock, or that are just
safe to be converted because read and write do not use ppos and there
are no other funky methods in file_operations.
Regarding semantic patch I've verified each generated change manually -
that it is correct to convert - and each other nonseekable_open instance
left - that it is either not correct to convert there, or that it is not
converted due to current stream_open.cocci limitations.
The script also does not convert files that should be valid to convert,
but that currently have .llseek = noop_llseek or generic_file_llseek for
unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Most, if not all, Quectel devices use dynamic interface numbers, and
users are able to change the USB configuration at will. Matching on for
example interface number is therefore not possible.
Instead, the QMI device can be identified by looking at the interface
class, subclass and protocol (all 0xff), as well as the number of
endpoints. The reason we need to look at the number of endpoints, is
that the diagnostic port interface has the same class, subclass and
protocol as QMI. However, the diagnostic port only has two endpoints,
while QMI has three.
Until now, we have identified the QMI device by combining a match on
class, subclass and protocol, with a call to the function
quectel_diag_detect(). In quectel_diag_detect(), we check if the number
of endpoints matches for known Quectel vendor/product ids.
Adding new vendor/product ids to quectel_diag_detect() is not a good
long-term solution. This commit replaces the function with a quirk, and
applies the quirk to affected Quectel devices that I have been able to
test the change with (EP06, EM12 and EC25). If the quirk is set and the
number of endpoints equal two, we return from qmi_wwan_probe() with
-ENODEV.
[In order for this patch to apply cleanly to 4.14, two minor changes had
to be made. First, the original work-around (quectel_diag_detect()) for
the dynamic interface numbers was never backported to 4.14, so there is
no need to remove this code. Second, support for the EM12 was also not
backported to 4.14. Since supporting EM12 is a trivial change (just
another VID/PID match), and the match for EM12 is changed by this patch,
I chose to not submit adding EM12-support as a separate patch.]
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to compute the uart state only on the first open. This is
usually what is done in the ->install hook. serial_core used to do this
in ->open on every open. So move it to ->install.
As a side effect, it ensures the state is set properly in the window
after tty_init_dev is called, but before uart_open. This fixes a bunch
of races between tty_open and flush_to_ldisc we were dealing with
recently.
One of such bugs was attempted to fix in commit fedb5760648a (serial:
fix race between flush_to_ldisc and tty_open), but it only took care of
a couple of functions (uart_start and uart_unthrottle). I was able to
reproduce the crash on a SLE system, but in uart_write_room which is
also called from flush_to_ldisc via process_echoes. I was *unable* to
reproduce the bug locally. It is due to having this patch in my queue
since 2012!
0 in rbx means tty->driver_data is NULL in uart_write_room. 0x178 is
tried to be dereferenced (0x178 >> 3 is 0x2f in rdx) at
uart_write_room+0xc4. 0x178 is exactly (struct uart_state *)NULL->refcount
used in uart_port_lock from uart_write_room.
So revert the upstream commit here as my local patch should fix the
whole family.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Li RongQing <lirongqing@baidu.com> Cc: Wang Li <wangli39@baidu.com> Cc: Zhang Yu <zhangyu31@baidu.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On many (all?) the Gemini Lake systems we work with, there is frequent
momentary graphical corruption at the top of the screen, and it seems
that disabling framebuffer compression can avoid this.
The ticket was reported 6 months ago and has already affected a
multitude of users, without any real progress being made. So, lets
disable framebuffer compression on GeminiLake until a solution is found.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108085 Fixes: fd7d6c5c8f3e ("drm/i915: enable FBC on gen9+ too") Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: <stable@vger.kernel.org> # v4.11+ Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190423092810.28359-1-jian-hong@endlessm.com
(cherry picked from commit 1d25724b41fad7eeb2c3058a5c8190d6ece73e08) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was supposed to be a mask of all known rings, but it is being used
by execbuffer to filter out invalid rings, and so is instead mapping high
unused values onto valid rings. Instead of a mask of all known rings,
we need it to be the mask of all possible rings.
Instead of the closest reference divider prefer the lowest,
this fixes flickering issues on HP Compaq nx9420.
Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=108514 Suggested-by: Paul Dufresne <dufresnep@gmail.com> Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case we need to use them for GPU reset prior initializing the
asic. Fixes a crash if the driver attempts to reset the GPU at driver
load time.
Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a nouveau DDX that relied on legacy context ioctls to work,
but we fixed it years ago, give distros that have a modern DDX the
option to break the uAPI and close the mess of holes that legacy
context support is.
The context functions are not used by the i915 driver and should not
be used by modeset drivers. These driver functions contain several bugs
and security holes. This change makes these functions optional can be
turned on by a setting, they are turned off by default for modeset
driver with the exception of the nouvea driver that may require them with
an old version of libdrm.
Revert "drm: mark context support as a legacy subsystem"
v2: remove returns from void function, and formatting (Daniel Vetter)
v3:
- s/Nova/nouveau/ in the commit message, and add references to the
previous attempts
- drop the part touching the drm hw lock, that should be a separate
patch.
Signed-off-by: Peter Antoine <peter.antoine@intel.com> (v2) Cc: Peter Antoine <peter.antoine@intel.com> (v2) Reviewed-by: Peter Antoine <peter.antoine@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: move DRM_VM dependency into legacy config.
v3: fix missing dep (kbuild robot)
Cc: stable@vger.kernel.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some machines have an lvds child device in vbt even though a panel is
not attached. To make detection more reliable we now also check the lvds
config bits available in the vbt.
The limit here is supposed to be how much of the page is left, but it's
just using PAGE_SIZE as the limit.
The other thing to remember is that snprintf() returns the number of
bytes which would have been copied if we had had enough room. So that
means that if we run out of space then this code would end up passing a
negative value as the limit and the kernel would print an error message.
I have change the code to use scnprintf() which returns the number of
bytes that were successfully printed (not counting the NUL terminator).
The first thing is that the "m->size + (...)" addition could overflow,
and the second is that round_up() overflows to zero if the result is
within PAGE_SIZE of the type max.
In this code, the "m->size" variable is an u64 but we're saving the
result in "map_size" which is an unsigned long and genwqe_user_vmap()
takes an unsigned long as well. So I have used ULONG_MAX as the upper
bound. From a practical perspective unsigned long is fine/better than
trying to change all the types to u64.
Fixes: eaf4722d4645 ("GenWQE Character device and DDCB queue") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Petr writes:
Karl has reported to me today, that he's experiencing weird
reboot hang on his devices with 4.9.180 kernel and that he has
bisected it down to my backported patch.
I would like to kindly ask you for removal of this patch. This
patch should be reverted from all stable kernels up to 5.1,
because perf counters were not broken on those kernels, and this
patch won't work on the ath79 legacy IRQ code anyway, it needs
new irqchip driver which was enabled on ath79 with commit 51fa4f8912c0 ("MIPS: ath79: drop legacy IRQ code").
Reported-by: Petr Štetiar <ynezz@true.cz> Cc: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Cc: John Crispin <john@phrozen.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pistachio platform uses the U-Boot bootloader & generally boots a
kernel in the uImage format. As such it's useful to build one when
building the kernel, but to do so currently requires the user to
manually specify a uImage target on the make command line.
Make uImage.gz the pistachio platform's default build target, so that
the default is to build a kernel image that we can actually boot on a
board such as the MIPS Creator Ci40.
Marked for stable backport as far as v4.1 where pistachio support was
introduced. This is primarily useful for CI systems such as kernelci.org
which will benefit from us building a suitable image which can then be
booted as part of automated testing, extending our test coverage to the
affected stable branches.
Signed-off-by: Paul Burton <paul.burton@mips.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com>
URL: https://groups.io/g/kernelci/message/388 Cc: stable@vger.kernel.org # v4.1+ Cc: linux-mips@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / people / arne_f / kernel.git / log
