+++ /dev/null
-Add initial support for cm-fx6 module.
-
-cm-fx6 is a module based on mx6q SoC with the following features:
-- Up to 4GB of DDR3
-- 1 LCD/DVI output port
-- 1 HDMI output port
-- 2 LVDS LCD ports
-- Gigabit Ethernet
-- Analog Audio
-- CAN
-- SATA
-- NAND
-- PCIE
-
-This patch allows to boot up the module, configures the serial console,
-the Ethernet adapter and the heartbeat led.
-
-cm-fx6 is embedded inside the Utilite computer.
-
-Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
-Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
----
-
-Shawn, can this still be applied for 3.13 ?
-
-diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
-index f0895c5..7521a34 100644
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -117,6 +117,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
- imx6dl-sabresd.dtb \
- imx6dl-wandboard.dtb \
- imx6q-arm2.dtb \
-+ imx6q-cm-fx6.dtb \
- imx6q-sabreauto.dtb \
- imx6q-sabrelite.dtb \
- imx6q-sabresd.dtb \
-diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
-new file mode 100644
-index 0000000..2419751
---- /dev/null
-+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
-@@ -0,0 +1,53 @@
-+/*
-+ * Copyright 2013 CompuLab Ltd.
-+ *
-+ * Author: Valentin Raevsky <valentin@compulab.co.il>
-+ *
-+ * The code contained herein is licensed under the GNU General Public
-+ * License. You may obtain a copy of the GNU General Public License
-+ * Version 2 or later at the following locations:
-+ *
-+ * http://www.opensource.org/licenses/gpl-license.html
-+ * http://www.gnu.org/copyleft/gpl.html
-+ */
-+
-+/dts-v1/;
-+#include "imx6q.dtsi"
-+
-+/ {
-+ model = "CompuLab CM-FX6";
-+ compatible = "compulab,cm-fx6", "fsl,imx6q";
-+
-+ memory {
-+ reg = <0x10000000 0x80000000>;
-+ };
-+
-+ leds {
-+ compatible = "gpio-leds";
-+
-+ heartbeat-led {
-+ label = "Heartbeat";
-+ gpios = <&gpio2 31 0>;
-+ linux,default-trigger = "heartbeat";
-+ };
-+ };
-+};
-+
-+&fec {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_enet_1>;
-+ phy-mode = "rgmii";
-+ status = "okay";
-+};
-+
-+&gpmi {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_gpmi_nand_1>;
-+ status = "okay";
-+};
-+
-+&uart4 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&pinctrl_uart4_1>;
-+ status = "okay";
-+};
+++ /dev/null
-diff -Naur linux-3.14.30.org/arch/arm/boot/dts/Makefile linux-3.14.30/arch/arm/boot/dts/Makefile
---- linux-3.14.30.org/arch/arm/boot/dts/Makefile 2015-01-29 19:56:17.000000000 +0100
-+++ linux-3.14.30/arch/arm/boot/dts/Makefile 2015-01-29 20:41:06.598335182 +0100
-@@ -304,6 +304,7 @@
- sun5i-a13-olinuxino-micro.dtb \
- sun6i-a31-colombus.dtb \
- sun7i-a20-bananapi.dtb \
-+ sun7i-a20-bananapro.dtb \
- sun7i-a20-cubieboard2.dtb \
- sun7i-a20-cubietruck.dtb \
- sun7i-a20-lamobo-r1.dtb \
-diff -Naur linux-3.14.30.org/arch/arm/boot/dts/sun7i-a20-bananapi.dts linux-3.14.30/arch/arm/boot/dts/sun7i-a20-bananapi.dts
---- linux-3.14.30.org/arch/arm/boot/dts/sun7i-a20-bananapi.dts 2015-01-29 19:56:17.000000000 +0100
-+++ linux-3.14.30/arch/arm/boot/dts/sun7i-a20-bananapi.dts 2015-01-29 20:33:18.143334959 +0100
-@@ -199,7 +199,7 @@
- regulator-name = "gmac-3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-- startup-delay-us = <50000>;
-+ startup-delay-us = <100000>;
- enable-active-high;
- gpio = <&pio 7 23 0>;
- status = "okay";
-diff -Naur linux-3.14.30.org/arch/arm/boot/dts/sun7i-a20-bananapro.dts linux-3.14.30/arch/arm/boot/dts/sun7i-a20-bananapro.dts
---- linux-3.14.30.org/arch/arm/boot/dts/sun7i-a20-bananapro.dts 1970-01-01 01:00:00.000000000 +0100
-+++ linux-3.14.30/arch/arm/boot/dts/sun7i-a20-bananapro.dts 2015-01-29 20:40:45.153335172 +0100
-@@ -0,0 +1,262 @@
-+/*
-+ * Copyright 2015 Arne Fitzenreiter
-+ * Arne Fitzenreiter <arne_f@ipfire.org>
-+ *
-+ * The code contained herein is licensed under the GNU General Public
-+ * License. You may obtain a copy of the GNU General Public License
-+ * Version 2 or later at the following locations:
-+ *
-+ * http://www.opensource.org/licenses/gpl-license.html
-+ * http://www.gnu.org/copyleft/gpl.html
-+ */
-+
-+/dts-v1/;
-+/include/ "sun7i-a20.dtsi"
-+/include/ "sunxi-common-regulators.dtsi"
-+#include <dt-bindings/input/input.h>
-+
-+/ {
-+ model = "LeMaker Banana Pro";
-+ compatible = "lemaker,bananapro", "allwinner,sun7i-a20";
-+
-+ aliases {
-+ spi0 = &spi1;
-+ spi1 = &spi2;
-+ };
-+
-+ soc@01c00000 {
-+ spi1: spi@01c06000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi1_pins_a>;
-+ status = "okay";
-+ };
-+
-+ spi2: spi@01c17000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi2_pins_a>;
-+ status = "okay";
-+ };
-+
-+ mmc0: mmc@01c0f000 {
-+ pinctrl-names = "default", "default";
-+ pinctrl-0 = <&mmc0_pins_a>;
-+ pinctrl-1 = <&mmc0_cd_pin_bananapi>;
-+ cd-gpios = <&pio 7 10 0>; /* PH10 */
-+ status = "okay";
-+ };
-+
-+ mmc3: mmc@01c12000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&mmc3_pins_a>;
-+ vmmc-supply = <®_vmmc3>;
-+ bus-width = <4>;
-+ non-removable;
-+ status = "okay";
-+ };
-+
-+ usbphy: phy@01c13400 {
-+ usb1_vbus-supply = <®_usb1_vbus>;
-+ usb2_vbus-supply = <®_usb2_vbus>;
-+ status = "okay";
-+ };
-+
-+ ehci0: usb@01c14000 {
-+ status = "okay";
-+ };
-+
-+ ohci0: usb@01c14400 {
-+ status = "okay";
-+ };
-+
-+ ahci: sata@01c18000 {
-+ target-supply = <®_ahci_5v>;
-+ status = "okay";
-+ };
-+
-+ ehci1: usb@01c1c000 {
-+ status = "okay";
-+ };
-+
-+ ohci1: usb@01c1c400 {
-+ status = "okay";
-+ };
-+
-+ pinctrl@01c20800 {
-+ usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
-+ allwinner,pins = "PH0";
-+ allwinner,function = "gpio_out";
-+ allwinner,drive = <0>;
-+ allwinner,pull = <0>;
-+ };
-+
-+ usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
-+ allwinner,pins = "PH1";
-+ allwinner,function = "gpio_out";
-+ allwinner,drive = <0>;
-+ allwinner,pull = <0>;
-+ };
-+
-+ led_pins_bananapi: led_pins@0 {
-+ allwinner,pins = "PH24", "PG2";
-+ allwinner,function = "gpio_out";
-+ allwinner,drive = <0>;
-+ allwinner,pull = <0>;
-+ };
-+
-+ mmc0_cd_pin_bananapi: mmc0_cd_pin@0 {
-+ allwinner,pins = "PH10";
-+ allwinner,function = "gpio_in";
-+ allwinner,drive = <0>;
-+ allwinner,pull = <1>;
-+ };
-+
-+ vmmc3_pin_bananapro: vmmc3_pin@0 {
-+ allwinner,pins = "PH22";
-+ allwinner,function = "gpio_out";
-+ allwinner,drive = <0>;
-+ allwinner,pull = <0>;
-+ };
-+
-+ gmac_power_pin_bananapi: gmac_power_pin@0 {
-+ allwinner,pins = "PH23";
-+ allwinner,function = "gpio_out";
-+ allwinner,drive = <0>;
-+ allwinner,pull = <0>;
-+ };
-+ };
-+
-+ lradc: lradc@01c22800 {
-+ allwinner,chan0-step = <200>;
-+ linux,chan0-keycodes = <KEY_VOLUMEUP KEY_VOLUMEDOWN
-+ KEY_MENU KEY_SEARCH KEY_HOME
-+ KEY_ESC KEY_ENTER>;
-+ status = "okay";
-+ };
-+
-+ ir0: ir@01c21800 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&ir0_pins_a>;
-+ status = "okay";
-+ };
-+
-+ uart0: serial@01c28000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart0_pins_a>;
-+ status = "okay";
-+ };
-+
-+ uart2: serial@01c28800 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart2_pins_a>;
-+ status = "okay";
-+ };
-+
-+ uart6: serial@01c29800 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart6_pins_a>;
-+ status = "okay";
-+ };
-+
-+ uart7: serial@01c29c00 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart7_pins_a>;
-+ status = "okay";
-+ };
-+
-+ i2c0: i2c@01c2ac00 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c0_pins_a>;
-+ status = "okay";
-+
-+ axp: axp20x@34 {
-+ reg = <0x34>;
-+ interrupt-parent = <&nmi_intc>;
-+ interrupts = <0 8>;
-+ axp,system-power-controller;
-+ /include/ "x-powers-axp209.dtsi"
-+ };
-+ };
-+
-+ i2c1: i2c@01c2b000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c1_pins_a>;
-+ status = "okay";
-+ };
-+
-+ i2c2: i2c@01c2b400 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&i2c2_pins_a>;
-+ status = "okay";
-+ };
-+
-+ gmac: ethernet@01c50000 {
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&gmac_pins_rgmii_a>;
-+ phy = <&phy1>;
-+ phy-mode = "rgmii";
-+ phy-supply = <®_gmac_3v3>;
-+ status = "okay";
-+
-+ phy1: ethernet-phy@1 {
-+ reg = <1>;
-+ };
-+ };
-+ };
-+
-+ leds {
-+ compatible = "gpio-leds";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&led_pins_bananapi>;
-+
-+ green {
-+ label = "bananapi:green:usr";
-+ gpios = <&pio 7 24 0>;
-+ linux,default-trigger = "heartbeat";
-+ };
-+ blue {
-+ label = "bananapi:blue:usr";
-+ gpios = <&pio 6 2 0>;
-+ linux,default-trigger = "mmc0";
-+ };
-+ };
-+
-+ reg_ahci_5v: ahci-5v {
-+ status = "okay";
-+ };
-+
-+ reg_usb1_vbus: usb1-vbus {
-+ pinctrl-0 = <&usb1_vbus_pin_bananapro>;
-+ gpio = <&pio 7 0 0>; /* PH0 */
-+ status = "okay";
-+ };
-+
-+ reg_usb2_vbus: usb2-vbus {
-+ pinctrl-0 = <&usb2_vbus_pin_bananapro>;
-+ gpio = <&pio 7 1 0>; /* PH1 */
-+ status = "okay";
-+ };
-+
-+ reg_gmac_3v3: gmac-3v3 {
-+ compatible = "regulator-fixed";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&gmac_power_pin_bananapi>;
-+ regulator-name = "gmac-3v3";
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+ startup-delay-us = <100000>;
-+ enable-active-high;
-+ gpio = <&pio 7 23 0>;
-+ status = "okay";
-+ };
-+
-+ reg_vmmc3: vmmc3 {
-+ compatible = "regulator-fixed";
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&vmmc3_pin_bananapro>;
-+ regulator-name = "vmmc3";
-+ regulator-min-microvolt = <3300000>;
-+ regulator-max-microvolt = <3300000>;
-+ enable-active-high;
-+ gpio = <&pio 7 22 0>;
-+ };
-+};
-diff -Naur linux-3.14.30.org/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts linux-3.14.30/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts
---- linux-3.14.30.org/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts 2015-01-29 19:56:17.000000000 +0100
-+++ linux-3.14.30/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts 2015-01-30 00:00:01.678340873 +0100
-@@ -199,7 +199,7 @@
- regulator-name = "gmac-3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-- startup-delay-us = <50000>;
-+ startup-delay-us = <100000>;
- enable-active-high;
- gpio = <&pio 7 23 0>;
- status = "okay";