]>
Commit | Line | Data |
---|---|---|
110fa979 WY |
1 | /* |
2 | * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board | |
3 | * | |
4 | * Copyright (C) 2016 Atmel, | |
5 | * | |
6 | * Licensed under GPLv2 or later. | |
7 | */ | |
8 | #include "sama5d3xcm_cmp.dtsi" | |
9 | ||
10 | / { | |
11 | compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5"; | |
12 | ||
13 | chosen { | |
14 | u-boot,dm-pre-reloc; | |
15 | stdout-path = &dbgu; | |
16 | }; | |
17 | ||
18 | ahb { | |
19 | apb { | |
20 | mmc0: mmc@f0000000 { | |
21 | pinctrl-names = "default"; | |
22 | pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>; | |
23 | status = "okay"; | |
24 | slot@0 { | |
25 | reg = <0>; | |
26 | bus-width = <4>; | |
27 | cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>; | |
28 | }; | |
29 | }; | |
30 | ||
31 | spi0: spi@f0004000 { | |
32 | dmas = <0>, <0>; /* Do not use DMA for spi0 */ | |
33 | ||
34 | spi_flash@0 { | |
35 | compatible = "spi-flash"; | |
36 | spi-max-frequency = <50000000>; | |
37 | reg = <0>; | |
38 | }; | |
39 | }; | |
40 | ||
41 | ssc0: ssc@f0008000 { | |
42 | atmel,clk-from-rk-pin; | |
43 | }; | |
44 | ||
45 | /* | |
46 | * i2c0 conflicts with ISI: | |
47 | * disable it to allow the use of ISI | |
48 | * can not enable audio when i2c0 disabled | |
49 | */ | |
50 | i2c0: i2c@f0014000 { | |
51 | wm8904: wm8904@1a { | |
52 | compatible = "wlf,wm8904"; | |
53 | reg = <0x1a>; | |
54 | clocks = <&pck0>; | |
55 | clock-names = "mclk"; | |
56 | }; | |
57 | }; | |
58 | ||
59 | i2c1: i2c@f0018000 { | |
60 | ov2640: camera@0x30 { | |
61 | compatible = "ovti,ov2640"; | |
62 | reg = <0x30>; | |
63 | pinctrl-names = "default"; | |
64 | pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; | |
65 | resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>; | |
66 | pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; | |
67 | /* use pck1 for the master clock of ov2640 */ | |
68 | clocks = <&pck1>; | |
69 | clock-names = "xvclk"; | |
70 | assigned-clocks = <&pck1>; | |
71 | assigned-clock-rates = <25000000>; | |
72 | ||
73 | port { | |
74 | ov2640_0: endpoint { | |
75 | remote-endpoint = <&isi_0>; | |
76 | bus-width = <8>; | |
77 | }; | |
78 | }; | |
79 | }; | |
80 | }; | |
81 | ||
82 | usart1: serial@f0020000 { | |
83 | dmas = <0>, <0>; /* Do not use DMA for usart1 */ | |
84 | pinctrl-names = "default"; | |
85 | pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>; | |
86 | status = "okay"; | |
87 | }; | |
88 | ||
89 | isi: isi@f0034000 { | |
90 | port { | |
91 | isi_0: endpoint { | |
92 | remote-endpoint = <&ov2640_0>; | |
93 | bus-width = <8>; | |
94 | vsync-active = <1>; | |
95 | hsync-active = <1>; | |
96 | }; | |
97 | }; | |
98 | }; | |
99 | ||
100 | mmc1: mmc@f8000000 { | |
101 | pinctrl-names = "default"; | |
102 | pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>; | |
103 | status = "okay"; | |
104 | slot@0 { | |
105 | reg = <0>; | |
106 | bus-width = <4>; | |
107 | cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>; | |
108 | }; | |
109 | }; | |
110 | ||
111 | adc0: adc@f8018000 { | |
112 | pinctrl-names = "default"; | |
113 | pinctrl-0 = < | |
114 | &pinctrl_adc0_adtrg | |
115 | &pinctrl_adc0_ad0 | |
116 | &pinctrl_adc0_ad1 | |
117 | &pinctrl_adc0_ad2 | |
118 | &pinctrl_adc0_ad3 | |
119 | &pinctrl_adc0_ad4 | |
120 | >; | |
121 | status = "okay"; | |
122 | }; | |
123 | ||
124 | macb1: ethernet@f802c000 { | |
125 | phy-mode = "rmii"; | |
126 | ||
127 | #address-cells = <1>; | |
128 | #size-cells = <0>; | |
129 | phy0: ethernet-phy@1 { | |
130 | /*interrupt-parent = <&pioE>;*/ | |
131 | /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/ | |
132 | reg = <1>; | |
133 | }; | |
134 | }; | |
135 | ||
136 | pinctrl@fffff200 { | |
137 | board { | |
138 | pinctrl_gpio_keys: gpio_keys { | |
139 | atmel,pins = | |
140 | <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; | |
141 | }; | |
142 | ||
143 | pinctrl_mmc0_cd: mmc0_cd { | |
144 | atmel,pins = | |
145 | <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */ | |
146 | }; | |
147 | ||
148 | pinctrl_mmc1_cd: mmc1_cd { | |
149 | atmel,pins = | |
150 | <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */ | |
151 | }; | |
152 | ||
153 | pinctrl_pck0_as_audio_mck: pck0_as_audio_mck { | |
154 | atmel,pins = | |
155 | <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */ | |
156 | }; | |
157 | ||
158 | pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 { | |
159 | atmel,pins = | |
160 | <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */ | |
161 | }; | |
162 | ||
163 | pinctrl_sensor_reset: sensor_reset-0 { | |
164 | atmel,pins = | |
165 | <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */ | |
166 | }; | |
167 | ||
168 | pinctrl_sensor_power: sensor_power-0 { | |
169 | atmel,pins = | |
170 | <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */ | |
171 | }; | |
172 | ||
173 | pinctrl_usba_vbus: usba_vbus { | |
174 | atmel,pins = | |
175 | <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */ | |
176 | }; | |
177 | }; | |
178 | }; | |
179 | ||
180 | dbgu: serial@ffffee00 { | |
181 | dmas = <0>, <0>; /* Do not use DMA for dbgu */ | |
182 | status = "okay"; | |
183 | u-boot,dm-pre-reloc; | |
184 | }; | |
185 | ||
186 | watchdog@fffffe40 { | |
187 | status = "okay"; | |
188 | }; | |
189 | }; | |
190 | ||
191 | usb0: gadget@00500000 { | |
192 | atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>; | |
193 | pinctrl-names = "default"; | |
194 | pinctrl-0 = <&pinctrl_usba_vbus>; | |
195 | status = "okay"; | |
196 | }; | |
197 | }; | |
198 | ||
199 | sound { | |
200 | compatible = "atmel,asoc-wm8904"; | |
201 | pinctrl-names = "default"; | |
202 | pinctrl-0 = <&pinctrl_pck0_as_audio_mck>; | |
203 | ||
204 | atmel,model = "wm8904 @ SAMA5D3EK"; | |
205 | atmel,audio-routing = | |
206 | "Headphone Jack", "HPOUTL", | |
207 | "Headphone Jack", "HPOUTR", | |
208 | "IN2L", "Line In Jack", | |
209 | "IN2R", "Line In Jack", | |
210 | "Mic", "MICBIAS", | |
211 | "IN1L", "Mic"; | |
212 | ||
213 | atmel,ssc-controller = <&ssc0>; | |
214 | atmel,audio-codec = <&wm8904>; | |
215 | ||
216 | status = "disabled"; | |
217 | }; | |
218 | ||
219 | /* Conflict with LCD pins */ | |
220 | gpio_keys { | |
221 | compatible = "gpio-keys"; | |
222 | status = "okay"; | |
223 | ||
224 | #address-cells = <1>; | |
225 | #size-cells = <0>; | |
226 | pinctrl-names = "default"; | |
227 | pinctrl-0 = <&pinctrl_gpio_keys>; | |
228 | ||
229 | pb_user1 { | |
230 | label = "pb_user1"; | |
231 | gpios = <&pioE 27 GPIO_ACTIVE_HIGH>; | |
232 | linux,code = <0x100>; | |
233 | gpio-key,wakeup; | |
234 | }; | |
235 | }; | |
236 | }; |