[people/ms/u-boot.git] / board / LaCie / netspace_v2 / kwbimage.cfg

#
# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
#
# Based on Kirkwood support:
# (C) Copyright 2009
# Marvell Semiconductor <www.marvell.com>
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
#
# SPDX-License-Identifier:	GPL-2.0+
#
# Refer doc/README.kwbimage for more details about how-to configure
# and create kirkwood boot image
#

# Boot Media configurations
BOOT_FROM	spi	# Boot from SPI flash

# SOC registers configuration using bootrom header extension
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed

# Configure RGMII-0 interface pad voltage to 1.8V
DATA 0xFFD100e0 0x1B1B1B9B

#Dram initalization for SINGLE x16 CL=5 @ 400MHz
DATA 0xFFD01400 0x43000618	# DDR Configuration register
# bit13-0:  0xa00 (2560 DDR2 clks refresh rate)
# bit23-14: zero
# bit24: 1= enable exit self refresh mode on DDR access
# bit25: 1 required
# bit29-26: zero
# bit31-30: 01

DATA 0xFFD01404 0x35143000	# DDR Controller Control Low
# bit 4:    0=addr/cmd in smame cycle
# bit 5:    0=clk is driven during self refresh, we don't care for APX
# bit 6:    0=use recommended falling edge of clk for addr/cmd
# bit14:    0=input buffer always powered up
# bit18:    1=cpu lock transaction enabled
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
# bit30-28: 3 required
# bit31:    0=no additional STARTBURST delay

DATA 0xFFD01408 0x11012228	# DDR Timing (Low) (active cycles value +1)
# bit7-4:   TRCD
# bit11- 8: TRP
# bit15-12: TWR
# bit19-16: TWTR
# bit20:    TRAS msb
# bit23-21: 0x0
# bit27-24: TRRD
# bit31-28: TRTP

DATA 0xFFD0140C 0x00000A19	#  DDR Timing (High)
# bit6-0:   TRFC
# bit8-7:   TR2R
# bit10-9:  TR2W
# bit12-11: TW2W
# bit31-13: zero required

DATA 0xFFD01410 0x0000000C	#  DDR Address Control
# bit1-0:   00, Cs0width=x8
# bit3-2:   11, Cs0size=1Gb
# bit5-4:   00, Cs2width=nonexistent
# bit7-6:   00, Cs1size =nonexistent
# bit9-8:   00, Cs2width=nonexistent
# bit11-10: 00, Cs2size =nonexistent
# bit13-12: 00, Cs3width=nonexistent
# bit15-14: 00, Cs3size =nonexistent
# bit16:    0,  Cs0AddrSel
# bit17:    0,  Cs1AddrSel
# bit18:    0,  Cs2AddrSel
# bit19:    0,  Cs3AddrSel
# bit31-20: 0 required

DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
# bit0:    0,  OpenPage enabled
# bit31-1: 0 required

DATA 0xFFD01418 0x00000000	#  DDR Operation
# bit3-0:   0x0, DDR cmd
# bit31-4:  0 required

DATA 0xFFD0141C 0x00000632	#  DDR Mode
# bit2-0:   2, BurstLen=2 required
# bit3:     0, BurstType=0 required
# bit6-4:   4, CL=5
# bit7:     0, TestMode=0 normal
# bit8:     0, DLL reset=0 normal
# bit11-9:  6, auto-precharge write recovery ????????????
# bit12:    0, PD must be zero
# bit31-13: 0 required

DATA 0xFFD01420 0x00000004	#  DDR Extended Mode
# bit0:    0,  DDR DLL enabled
# bit1:    1,  DDR drive strenght reduced
# bit2:    1,  DDR ODT control lsd enabled
# bit5-3:  000, required
# bit6:    1,  DDR ODT control msb, enabled
# bit9-7:  000, required
# bit10:   0,  differential DQS enabled
# bit11:   0, required
# bit12:   0, DDR output buffer enabled
# bit31-13: 0 required

DATA 0xFFD01424 0x0000F07F	#  DDR Controller Control High
# bit2-0:  111, required
# bit3  :  1  , MBUS Burst Chop disabled
# bit6-4:  111, required
# bit7  :  1  , D2P Latency enabled
# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
# bit9  :  0  , no half clock cycle addition to dataout
# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
# bit15-12: 1111 required
# bit31-16: 0    required

DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)

DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
# bit0:    1,  Window enabled
# bit1:    0,  Write Protect disabled
# bit3-2:  00, CS0 hit selected
# bit23-4: ones, required
# bit31-24: 0x07, Size (i.e. 128MB)

DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled

DATA 0xFFD01494 0x00010000	#  DDR ODT Control (Low)
# bit3-0:  1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0

DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
# bit3-2:  01, ODT1 active NEVER!
# bit31-4: zero, required

DATA 0xFFD0149C 0x0000E40F	# CPU ODT Control
# bit3-0:  1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
# bit7-4:  1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
# bit11-10:1, DQ_ODTSel. ODT select turned on

DATA 0xFFD01480 0x00000001	# DDR Initialization Control
#bit0=1, enable DDR init upon this register write

# End of Header extension
DATA 0x0 0x0
Commit	Line	Data
79642098 SG	1	#
	2	# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
	3	#
	4	# Based on Kirkwood support:
	5	# (C) Copyright 2009
	6	# Marvell Semiconductor <www.marvell.com>
	7	# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
	8	#
1a459660	9	# SPDX-License-Identifier: GPL-2.0+
79642098	10	#
b1e6c4c3	11	# Refer doc/README.kwbimage for more details about how-to configure
79642098 SG	12	# and create kirkwood boot image
	13	#
	14
	15	# Boot Media configurations
	16	BOOT_FROM spi # Boot from SPI flash
	17
	18	# SOC registers configuration using bootrom header extension
	19	# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
	20
	21	# Configure RGMII-0 interface pad voltage to 1.8V
	22	DATA 0xFFD100e0 0x1B1B1B9B
	23
	24	#Dram initalization for SINGLE x16 CL=5 @ 400MHz
	25	DATA 0xFFD01400 0x43000618 # DDR Configuration register
	26	# bit13-0: 0xa00 (2560 DDR2 clks refresh rate)
	27	# bit23-14: zero
	28	# bit24: 1= enable exit self refresh mode on DDR access
	29	# bit25: 1 required
	30	# bit29-26: zero
	31	# bit31-30: 01
	32
	33	DATA 0xFFD01404 0x35143000 # DDR Controller Control Low
	34	# bit 4: 0=addr/cmd in smame cycle
	35	# bit 5: 0=clk is driven during self refresh, we don't care for APX
	36	# bit 6: 0=use recommended falling edge of clk for addr/cmd
	37	# bit14: 0=input buffer always powered up
	38	# bit18: 1=cpu lock transaction enabled
	39	# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
	40	# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
	41	# bit30-28: 3 required
	42	# bit31: 0=no additional STARTBURST delay
	43
	44	DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
	45	# bit7-4: TRCD
	46	# bit11- 8: TRP
	47	# bit15-12: TWR
	48	# bit19-16: TWTR
	49	# bit20: TRAS msb
	50	# bit23-21: 0x0
	51	# bit27-24: TRRD
	52	# bit31-28: TRTP
	53
	54	DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
	55	# bit6-0: TRFC
	56	# bit8-7: TR2R
	57	# bit10-9: TR2W
	58	# bit12-11: TW2W
	59	# bit31-13: zero required
	60
f697997a SG	61	DATA 0xFFD01410 0x0000000C # DDR Address Control
f697997a SG	62	# bit1-0: 00, Cs0width=x8
79642098 SG	63	# bit3-2: 11, Cs0size=1Gb
	64	# bit5-4: 00, Cs2width=nonexistent
	65	# bit7-6: 00, Cs1size =nonexistent
	66	# bit9-8: 00, Cs2width=nonexistent
	67	# bit11-10: 00, Cs2size =nonexistent
	68	# bit13-12: 00, Cs3width=nonexistent
	69	# bit15-14: 00, Cs3size =nonexistent
	70	# bit16: 0, Cs0AddrSel
	71	# bit17: 0, Cs1AddrSel
	72	# bit18: 0, Cs2AddrSel
	73	# bit19: 0, Cs3AddrSel
	74	# bit31-20: 0 required
	75
	76	DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
	77	# bit0: 0, OpenPage enabled
	78	# bit31-1: 0 required
	79
	80	DATA 0xFFD01418 0x00000000 # DDR Operation
	81	# bit3-0: 0x0, DDR cmd
	82	# bit31-4: 0 required
	83
	84	DATA 0xFFD0141C 0x00000632 # DDR Mode
	85	# bit2-0: 2, BurstLen=2 required
	86	# bit3: 0, BurstType=0 required
	87	# bit6-4: 4, CL=5
	88	# bit7: 0, TestMode=0 normal
	89	# bit8: 0, DLL reset=0 normal
	90	# bit11-9: 6, auto-precharge write recovery ????????????
	91	# bit12: 0, PD must be zero
	92	# bit31-13: 0 required
	93
	94	DATA 0xFFD01420 0x00000004 # DDR Extended Mode
	95	# bit0: 0, DDR DLL enabled
	96	# bit1: 1, DDR drive strenght reduced
	97	# bit2: 1, DDR ODT control lsd enabled
	98	# bit5-3: 000, required
	99	# bit6: 1, DDR ODT control msb, enabled
	100	# bit9-7: 000, required
	101	# bit10: 0, differential DQS enabled
	102	# bit11: 0, required
	103	# bit12: 0, DDR output buffer enabled
	104	# bit31-13: 0 required
	105
	106	DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
	107	# bit2-0: 111, required
	108	# bit3 : 1 , MBUS Burst Chop disabled
	109	# bit6-4: 111, required
	110	# bit7 : 1 , D2P Latency enabled
	111	# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
	112	# bit9 : 0 , no half clock cycle addition to dataout
	113	# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
	114	# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
	115	# bit15-12: 1111 required
	116	# bit31-16: 0 required
	117
	118	DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
	119	DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
	120
	121	DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
	122	DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
	123	# bit0: 1, Window enabled
	124	# bit1: 0, Write Protect disabled
	125	# bit3-2: 00, CS0 hit selected
	126	# bit23-4: ones, required
127	# bit31-24: 0x07, Size (i.e. 128MB)
128
129	DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
130	DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
131	DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
132
133	DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low)
134	# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0
135	# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
136
137	DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
138	# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
139	# bit3-2: 01, ODT1 active NEVER!
140	# bit31-4: zero, required
141
142	DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
143	# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0
144	# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0
145	# bit11-10:1, DQ_ODTSel. ODT select turned on
146
147	DATA 0xFFD01480 0x00000001 # DDR Initialization Control
148	#bit0=1, enable DDR init upon this register write
149
150	# End of Header extension
151	DATA 0x0 0x0