[people/ms/u-boot.git] / board / cm5200 / cm5200.c

/*
 * (C) Copyright 2003-2007
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * (C) Copyright 2004
 * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
 *
 * (C) Copyright 2004-2005
 * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
 *
 * Adapted to U-Boot 1.2 by:
 *   Bartlomiej Sieka <tur@semihalf.com>:
 *      - HW ID readout from EEPROM
 *      - module detection
 *   Grzegorz Bernacki <gjb@semihalf.com>:
 *      - run-time SDRAM controller configuration
 *      - LIBFDT support
 *
 * SPDX-License-Identifier:	GPL-2.0+ 
 */

#include <common.h>
#include <mpc5xxx.h>
#include <pci.h>
#include <asm/processor.h>
#include <i2c.h>
#include <linux/ctype.h>

#ifdef CONFIG_OF_LIBFDT
#include <libfdt.h>
#include <fdt_support.h>
#endif /* CONFIG_OF_LIBFDT */


#include "cm5200.h"
#include "fwupdate.h"

DECLARE_GLOBAL_DATA_PTR;

static hw_id_t hw_id;


#ifndef CONFIG_SYS_RAMBOOT
/*
 * Helper function to initialize SDRAM controller.
 */
static void sdram_start(int hi_addr, mem_conf_t *mem_conf)
{
	long hi_addr_bit = hi_addr ? 0x01000000 : 0;

	/* unlock mode register */
	*(vu_long *)MPC5XXX_SDRAM_CTRL = mem_conf->control | 0x80000000 |
						hi_addr_bit;

	/* precharge all banks */
	*(vu_long *)MPC5XXX_SDRAM_CTRL = mem_conf->control | 0x80000002 |
						hi_addr_bit;

	/* auto refresh */
	*(vu_long *)MPC5XXX_SDRAM_CTRL = mem_conf->control | 0x80000004 |
						hi_addr_bit;

	/* auto refresh, second time */
	*(vu_long *)MPC5XXX_SDRAM_CTRL = mem_conf->control | 0x80000004 |
						hi_addr_bit;

	/* set mode register */
	*(vu_long *)MPC5XXX_SDRAM_MODE = mem_conf->mode;

	/* normal operation */
	*(vu_long *)MPC5XXX_SDRAM_CTRL = mem_conf->control | hi_addr_bit;
}
#endif /* CONFIG_SYS_RAMBOOT */


/*
 * Retrieve memory configuration for a given module. board_type is the index
 * in hw_id_list[] corresponding to the module we are executing on; we return
 * SDRAM controller settings approprate for this module.
 */
static mem_conf_t* get_mem_config(int board_type)
{
	switch(board_type){
		case CM1_QA:
			return memory_config[0];
		case CM11_QA:
		case CMU1_QA:
			return memory_config[1];
		default:
			printf("ERROR: Unknown module, using a default SDRAM "
				"configuration - things may not work!!!.\n");
			return memory_config[0];
	}
}


/*
 * Initalize SDRAM - configure SDRAM controller, detect memory size.
 */
phys_size_t initdram(int board_type)
{
	ulong dramsize = 0;
#ifndef CONFIG_SYS_RAMBOOT
	ulong test1, test2;
	mem_conf_t *mem_conf;

	mem_conf = get_mem_config(board_type);

	/* configure SDRAM start/end for detection */
	*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */

	/* setup config registers */
	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = mem_conf->config1;
	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = mem_conf->config2;

	sdram_start(0, mem_conf);
	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
	sdram_start(1, mem_conf);
	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
	if (test1 > test2) {
		sdram_start(0, mem_conf);
		dramsize = test1;
	} else
		dramsize = test2;

	/* memory smaller than 1MB is impossible */
	if (dramsize < (1 << 20))
		dramsize = 0;

	/* set SDRAM CS0 size according to the amount of RAM found */
	if (dramsize > 0) {
		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
			__builtin_ffs(dramsize >> 20) - 1;
	} else
		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
#else /* CONFIG_SYS_RAMBOOT */
	/* retrieve size of memory connected to SDRAM CS0 */
	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
	if (dramsize >= 0x13)
		dramsize = (1 << (dramsize - 0x13)) << 20;
	else
		dramsize = 0;
#endif /* !CONFIG_SYS_RAMBOOT */

	/*
	 * On MPC5200B we need to set the special configuration delay in the
	 * DDR controller.  Refer to chapter 8.7.5 SDelay--MBAR + 0x0190 of
	 * the MPC5200B User's Manual.
	 */
	*(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
	__asm__ volatile ("sync");

	return dramsize;
}


/*
 * Read module hardware identification data from the I2C EEPROM.
 */
static void read_hw_id(hw_id_t hw_id)
{
	int i;
	for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
		if (i2c_read(CONFIG_SYS_I2C_EEPROM,
				hw_id_format[i].offset,
				2,
				(uchar *)&hw_id[i][0],
				hw_id_format[i].length) != 0)
			printf("ERROR: can't read HW ID from EEPROM\n");
}


/*
 * Identify module we are running on, set gd->board_type to the index in
 * hw_id_list[] corresponding to the module identifed, or to
 * CM5200_UNKNOWN_MODULE if we can't identify the module.
 */
static void identify_module(hw_id_t hw_id)
{
	int i, j, element;
	char match;
	gd->board_type = CM5200_UNKNOWN_MODULE;
	for (i = 0; i < sizeof (hw_id_list) / sizeof (char **); ++i) {
		match = 1;
		for (j = 0; j < sizeof (hw_id_identify) / sizeof (int); ++j) {
			element = hw_id_identify[j];
			if (strncmp(hw_id_list[i][element],
					&hw_id[element][0],
					hw_id_format[element].length) != 0) {
				match = 0;
				break;
			}
		}
		if (match) {
			gd->board_type = i;
			break;
		}
	}
}


/*
 * Compose string with module name.
 * buf is assumed to have enough space, and be null-terminated.
 */
static void compose_module_name(hw_id_t hw_id, char *buf)
{
	char tmp[MODULE_NAME_MAXLEN];
	strncat(buf, &hw_id[PCB_NAME][0], hw_id_format[PCB_NAME].length);
	strncat(buf, ".", 1);
	strncat(buf, &hw_id[FORM][0], hw_id_format[FORM].length);
	strncat(buf, &hw_id[VERSION][0], hw_id_format[VERSION].length);
	strncat(buf, " (", 2);
	strncat(buf, &hw_id[IDENTIFICATION_NUMBER][0],
		hw_id_format[IDENTIFICATION_NUMBER].length);
	sprintf(tmp, " / %u.%u)",
		hw_id[MAJOR_SW_VERSION][0],
		hw_id[MINOR_SW_VERSION][0]);
	strcat(buf, tmp);
}


/*
 * Compose string with hostname.
 * buf is assumed to have enough space, and be null-terminated.
 */
static void compose_hostname(hw_id_t hw_id, char *buf)
{
	char *p;
	strncat(buf, &hw_id[PCB_NAME][0], hw_id_format[PCB_NAME].length);
	strncat(buf, "_", 1);
	strncat(buf, &hw_id[FORM][0], hw_id_format[FORM].length);
	strncat(buf, &hw_id[VERSION][0], hw_id_format[VERSION].length);
	for (p = buf; *p; ++p)
		*p = tolower(*p);

}


#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
/*
 * Update 'model' and 'memory' properties in the blob according to the module
 * that we are running on.
 */
static void ft_blob_update(void *blob, bd_t *bd)
{
	int len, ret, nodeoffset = 0;
	char module_name[MODULE_NAME_MAXLEN] = {0};

	compose_module_name(hw_id, module_name);
	len = strlen(module_name) + 1;

	ret = fdt_setprop(blob, nodeoffset, "model", module_name, len);
	if (ret < 0)
	printf("ft_blob_update(): cannot set /model property err:%s\n",
		fdt_strerror(ret));
}
#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */


/*
 * Read HW ID from I2C EEPROM and detect the modue we are running on. Note
 * that we need to use local variable for readout, because global data is not
 * writable yet (and we'll have to redo the readout later on).
 */
int checkboard(void)
{
	hw_id_t hw_id_tmp;
	char module_name_tmp[MODULE_NAME_MAXLEN] = "";

	/*
	 * We need I2C to access HW ID data from EEPROM, so we call i2c_init()
	 * here despite the fact that it will be called again later on. We
	 * also use a little trick to silence I2C-related output.
	 */
	gd->flags |= GD_FLG_SILENT;
	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
	gd->flags &= ~GD_FLG_SILENT;

	read_hw_id(hw_id_tmp);
	identify_module(hw_id_tmp);	/* this sets gd->board_type */
	compose_module_name(hw_id_tmp, module_name_tmp);

	if (gd->board_type != CM5200_UNKNOWN_MODULE)
		printf("Board: %s\n", module_name_tmp);
	else
		printf("Board: unrecognized cm5200 module (%s)\n",
			module_name_tmp);

	return 0;
}


int board_early_init_r(void)
{
	/*
	 * Now, when we are in RAM, enable flash write access for detection
	 * process. Note that CS_BOOT cannot be cleared when executing in
	 * flash.
	 */
	*(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */

	/* Now that we can write to global data, read HW ID again. */
	read_hw_id(hw_id);
	return 0;
}


#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
	uchar buf[6];
	char str[18];
	char hostname[MODULE_NAME_MAXLEN];

	/* Read ethaddr from EEPROM */
	if (i2c_read(CONFIG_SYS_I2C_EEPROM, CONFIG_MAC_OFFSET, 2, buf, 6) == 0) {
		sprintf(str, "%02X:%02X:%02X:%02X:%02X:%02X",
			buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]);
		/* Check if MAC addr is owned by Schindler */
		if (strstr(str, "00:06:C3") != str)
			printf(LOG_PREFIX "Warning - Illegal MAC address (%s)"
				" in EEPROM.\n", str);
		else {
			printf(LOG_PREFIX "Using MAC (%s) from I2C EEPROM\n",
				str);
			setenv("ethaddr", str);
		}
	} else {
		printf(LOG_PREFIX "Warning - Unable to read MAC from I2C"
			" device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
			CONFIG_MAC_OFFSET);
	}
#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) */
	if (!getenv("ethaddr"))
		printf(LOG_PREFIX "MAC address not set, networking is not "
					"operational\n");

	/* set the hostname appropriate to the module we're running on */
	hostname[0] = 0x00;
	compose_hostname(hw_id, hostname);
	setenv("hostname", hostname);

	return 0;
}
#endif /* CONFIG_MISC_INIT_R */


#ifdef CONFIG_LAST_STAGE_INIT
int last_stage_init(void)
{
#ifdef CONFIG_USB_STORAGE
	cm5200_fwupdate();
#endif /* CONFIG_USB_STORAGE */
	return 0;
}
#endif /* CONFIG_LAST_STAGE_INIT */


#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
	ft_cpu_setup(blob, bd);
	ft_blob_update(blob, bd);
}
#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
Commit	Line	Data
86b116b1 BS	1	/*
	2	* (C) Copyright 2003-2007
	3	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	4	*
	5	* (C) Copyright 2004
	6	* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
	7	*
	8	* (C) Copyright 2004-2005
	9	* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
	10	*
	11	* Adapted to U-Boot 1.2 by:
	12	* Bartlomiej Sieka <tur@semihalf.com>:
	13	* - HW ID readout from EEPROM
	14	* - module detection
	15	* Grzegorz Bernacki <gjb@semihalf.com>:
	16	* - run-time SDRAM controller configuration
	17	* - LIBFDT support
	18	*
1a459660	19	* SPDX-License-Identifier: GPL-2.0+
86b116b1 BS	20	*/
	21
	22	#include <common.h>
	23	#include <mpc5xxx.h>
	24	#include <pci.h>
	25	#include <asm/processor.h>
	26	#include <i2c.h>
	27	#include <linux/ctype.h>
	28
	29	#ifdef CONFIG_OF_LIBFDT
	30	#include <libfdt.h>
86b116b1 BS	31	#include <fdt_support.h>
	32	#endif /* CONFIG_OF_LIBFDT */
	33
	34
	35	#include "cm5200.h"
	36	#include "fwupdate.h"
	37
	38	DECLARE_GLOBAL_DATA_PTR;
	39
	40	static hw_id_t hw_id;
	41
	42
6d0f6bcf	43	#ifndef CONFIG_SYS_RAMBOOT
86b116b1 BS	44	/*
	45	* Helper function to initialize SDRAM controller.
	46	*/
	47	static void sdram_start(int hi_addr, mem_conf_t *mem_conf)
	48	{
	49	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
	50
	51	/* unlock mode register */
	52	(vu_long )MPC5XXX_SDRAM_CTRL = mem_conf->control \| 0x80000000 \|
	53	hi_addr_bit;
	54
	55	/* precharge all banks */
	56	(vu_long )MPC5XXX_SDRAM_CTRL = mem_conf->control \| 0x80000002 \|
	57	hi_addr_bit;
	58
	59	/* auto refresh */
	60	(vu_long )MPC5XXX_SDRAM_CTRL = mem_conf->control \| 0x80000004 \|
	61	hi_addr_bit;
	62
	63	/* auto refresh, second time */
	64	(vu_long )MPC5XXX_SDRAM_CTRL = mem_conf->control \| 0x80000004 \|
	65	hi_addr_bit;
	66
	67	/* set mode register */
	68	(vu_long )MPC5XXX_SDRAM_MODE = mem_conf->mode;
	69
	70	/* normal operation */
	71	(vu_long )MPC5XXX_SDRAM_CTRL = mem_conf->control \| hi_addr_bit;
	72	}
6d0f6bcf	73	#endif /* CONFIG_SYS_RAMBOOT */
86b116b1 BS	74
	75
	76	/*
	77	* Retrieve memory configuration for a given module. board_type is the index
	78	* in hw_id_list[] corresponding to the module we are executing on; we return
	79	* SDRAM controller settings approprate for this module.
	80	*/
	81	static mem_conf_t* get_mem_config(int board_type)
	82	{
	83	switch(board_type){
	84	case CM1_QA:
	85	return memory_config[0];
	86	case CM11_QA:
	87	case CMU1_QA:
	88	return memory_config[1];
	89	default:
	90	printf("ERROR: Unknown module, using a default SDRAM "
	91	"configuration - things may not work!!!.\n");
	92	return memory_config[0];
	93	}
	94	}
	95
	96
	97	/*
	98	* Initalize SDRAM - configure SDRAM controller, detect memory size.
	99	*/
9973e3c6	100	phys_size_t initdram(int board_type)
86b116b1 BS	101	{
86b116b1 BS	102	ulong dramsize = 0;
6d0f6bcf	103	#ifndef CONFIG_SYS_RAMBOOT
86b116b1 BS	104	ulong test1, test2;
	105	mem_conf_t *mem_conf;
	106
	107	mem_conf = get_mem_config(board_type);
be5d72d1	108
86b116b1 BS	109	/* configure SDRAM start/end for detection */
	110	(vu_long )MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
	111
	112	/* setup config registers */
	113	(vu_long )MPC5XXX_SDRAM_CONFIG1 = mem_conf->config1;
	114	(vu_long )MPC5XXX_SDRAM_CONFIG2 = mem_conf->config2;
	115
	116	sdram_start(0, mem_conf);
6d0f6bcf	117	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
86b116b1	118	sdram_start(1, mem_conf);
6d0f6bcf	119	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
86b116b1 BS	120	if (test1 > test2) {
	121	sdram_start(0, mem_conf);
	122	dramsize = test1;
	123	} else
	124	dramsize = test2;
	125
	126	/* memory smaller than 1MB is impossible */
	127	if (dramsize < (1 << 20))
	128	dramsize = 0;
	129
	130	/* set SDRAM CS0 size according to the amount of RAM found */
	131	if (dramsize > 0) {
	132	(vu_long )MPC5XXX_SDRAM_CS0CFG = 0x13 +
	133	__builtin_ffs(dramsize >> 20) - 1;
	134	} else
	135	(vu_long )MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
6d0f6bcf	136	#else /* CONFIG_SYS_RAMBOOT */
86b116b1 BS	137	/* retrieve size of memory connected to SDRAM CS0 */
	138	dramsize = (vu_long )MPC5XXX_SDRAM_CS0CFG & 0xFF;
	139	if (dramsize >= 0x13)
	140	dramsize = (1 << (dramsize - 0x13)) << 20;
	141	else
	142	dramsize = 0;
6d0f6bcf	143	#endif /* !CONFIG_SYS_RAMBOOT */
86b116b1 BS	144
	145	/*
	146	* On MPC5200B we need to set the special configuration delay in the
	147	* DDR controller. Refer to chapter 8.7.5 SDelay--MBAR + 0x0190 of
	148	* the MPC5200B User's Manual.
	149	*/
	150	(vu_long )MPC5XXX_SDRAM_SDELAY = 0x04;
	151	__asm__ volatile ("sync");
	152
	153	return dramsize;
	154	}
	155
	156
	157	/*
	158	* Read module hardware identification data from the I2C EEPROM.
	159	*/
	160	static void read_hw_id(hw_id_t hw_id)
	161	{
	162	int i;
	163	for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
6d0f6bcf	164	if (i2c_read(CONFIG_SYS_I2C_EEPROM,
86b116b1 BS	165	hw_id_format[i].offset,
	166	2,
	167	(uchar *)&hw_id[i][0],
	168	hw_id_format[i].length) != 0)
	169	printf("ERROR: can't read HW ID from EEPROM\n");
	170	}
	171
	172
	173	/*
	174	* Identify module we are running on, set gd->board_type to the index in
	175	* hw_id_list[] corresponding to the module identifed, or to
	176	* CM5200_UNKNOWN_MODULE if we can't identify the module.
	177	*/
	178	static void identify_module(hw_id_t hw_id)
	179	{
	180	int i, j, element;
	181	char match;
	182	gd->board_type = CM5200_UNKNOWN_MODULE;
	183	for (i = 0; i < sizeof (hw_id_list) / sizeof (char **); ++i) {
	184	match = 1;
	185	for (j = 0; j < sizeof (hw_id_identify) / sizeof (int); ++j) {
	186	element = hw_id_identify[j];
	187	if (strncmp(hw_id_list[i][element],
	188	&hw_id[element][0],
	189	hw_id_format[element].length) != 0) {
	190	match = 0;
	191	break;
	192	}
	193	}
	194	if (match) {
	195	gd->board_type = i;
	196	break;
	197	}
	198	}
	199	}
	200
	201
	202	/*
	203	* Compose string with module name.
	204	* buf is assumed to have enough space, and be null-terminated.
	205	*/
	206	static void compose_module_name(hw_id_t hw_id, char *buf)
	207	{
	208	char tmp[MODULE_NAME_MAXLEN];
	209	strncat(buf, &hw_id[PCB_NAME][0], hw_id_format[PCB_NAME].length);
	210	strncat(buf, ".", 1);
	211	strncat(buf, &hw_id[FORM][0], hw_id_format[FORM].length);
	212	strncat(buf, &hw_id[VERSION][0], hw_id_format[VERSION].length);
	213	strncat(buf, " (", 2);
	214	strncat(buf, &hw_id[IDENTIFICATION_NUMBER][0],
	215	hw_id_format[IDENTIFICATION_NUMBER].length);
	216	sprintf(tmp, " / %u.%u)",
	217	hw_id[MAJOR_SW_VERSION][0],
	218	hw_id[MINOR_SW_VERSION][0]);
	219	strcat(buf, tmp);
	220	}
	221
	222
	223	/*
	224	* Compose string with hostname.
	225	* buf is assumed to have enough space, and be null-terminated.
	226	*/
	227	static void compose_hostname(hw_id_t hw_id, char *buf)
	228	{
229	char *p;
230	strncat(buf, &hw_id[PCB_NAME][0], hw_id_format[PCB_NAME].length);
231	strncat(buf, "_", 1);
232	strncat(buf, &hw_id[FORM][0], hw_id_format[FORM].length);
233	strncat(buf, &hw_id[VERSION][0], hw_id_format[VERSION].length);
234	for (p = buf; *p; ++p)
235	p = tolower(p);
236
237	}
238
239
240	#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
241	/*
242	* Update 'model' and 'memory' properties in the blob according to the module
243	* that we are running on.
244	*/
245	static void ft_blob_update(void blob, bd_t bd)
246	{
247	int len, ret, nodeoffset = 0;
248	char module_name[MODULE_NAME_MAXLEN] = {0};
86b116b1 BS	249
	250	compose_module_name(hw_id, module_name);
	251	len = strlen(module_name) + 1;
	252
	253	ret = fdt_setprop(blob, nodeoffset, "model", module_name, len);
	254	if (ret < 0)
	255	printf("ft_blob_update(): cannot set /model property err:%s\n",
	256	fdt_strerror(ret));
86b116b1 BS	257	}
	258	#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
	259
	260
	261	/*
	262	* Read HW ID from I2C EEPROM and detect the modue we are running on. Note
	263	* that we need to use local variable for readout, because global data is not
	264	* writable yet (and we'll have to redo the readout later on).
	265	*/
	266	int checkboard(void)
	267	{
	268	hw_id_t hw_id_tmp;
	269	char module_name_tmp[MODULE_NAME_MAXLEN] = "";
	270
be5d72d1	271	/*
86b116b1 BS	272	* We need I2C to access HW ID data from EEPROM, so we call i2c_init()
	273	* here despite the fact that it will be called again later on. We
	274	* also use a little trick to silence I2C-related output.
	275	*/
	276	gd->flags \|= GD_FLG_SILENT;
6d0f6bcf	277	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
86b116b1 BS	278	gd->flags &= ~GD_FLG_SILENT;
	279
	280	read_hw_id(hw_id_tmp);
	281	identify_module(hw_id_tmp); /* this sets gd->board_type */
	282	compose_module_name(hw_id_tmp, module_name_tmp);
	283
	284	if (gd->board_type != CM5200_UNKNOWN_MODULE)
	285	printf("Board: %s\n", module_name_tmp);
	286	else
	287	printf("Board: unrecognized cm5200 module (%s)\n",
	288	module_name_tmp);
be5d72d1	289
86b116b1 BS	290	return 0;
	291	}
	292
	293
	294	int board_early_init_r(void)
	295	{
	296	/*
	297	* Now, when we are in RAM, enable flash write access for detection
	298	* process. Note that CS_BOOT cannot be cleared when executing in
	299	* flash.
	300	*/
	301	(vu_long )MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
	302
	303	/* Now that we can write to global data, read HW ID again. */
	304	read_hw_id(hw_id);
	305	return 0;
	306	}
	307
	308
86b116b1 BS	309	#ifdef CONFIG_MISC_INIT_R
	310	int misc_init_r(void)
	311	{
	312	#if defined(CONFIG_HARD_I2C) \|\| defined(CONFIG_SOFT_I2C)
	313	uchar buf[6];
	314	char str[18];
	315	char hostname[MODULE_NAME_MAXLEN];
	316
	317	/* Read ethaddr from EEPROM */
6d0f6bcf	318	if (i2c_read(CONFIG_SYS_I2C_EEPROM, CONFIG_MAC_OFFSET, 2, buf, 6) == 0) {
86b116b1 BS	319	sprintf(str, "%02X:%02X:%02X:%02X:%02X:%02X",
	320	buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]);
	321	/* Check if MAC addr is owned by Schindler */
	322	if (strstr(str, "00:06:C3") != str)
	323	printf(LOG_PREFIX "Warning - Illegal MAC address (%s)"
	324	" in EEPROM.\n", str);
	325	else {
	326	printf(LOG_PREFIX "Using MAC (%s) from I2C EEPROM\n",
	327	str);
	328	setenv("ethaddr", str);
	329	}
	330	} else {
	331	printf(LOG_PREFIX "Warning - Unable to read MAC from I2C"
6d0f6bcf	332	" device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
86b116b1 BS	333	CONFIG_MAC_OFFSET);
	334	}
	335	#endif /* defined(CONFIG_HARD_I2C) \|\| defined(CONFIG_SOFT_I2C) */
	336	if (!getenv("ethaddr"))
	337	printf(LOG_PREFIX "MAC address not set, networking is not "
	338	"operational\n");
	339
	340	/* set the hostname appropriate to the module we're running on */
92869195	341	hostname[0] = 0x00;
86b116b1 BS	342	compose_hostname(hw_id, hostname);
	343	setenv("hostname", hostname);
	344
	345	return 0;
	346	}
	347	#endif /* CONFIG_MISC_INIT_R */
	348
	349
	350	#ifdef CONFIG_LAST_STAGE_INIT
	351	int last_stage_init(void)
	352	{
	353	#ifdef CONFIG_USB_STORAGE
	354	cm5200_fwupdate();
	355	#endif /* CONFIG_USB_STORAGE */
	356	return 0;
	357	}
	358	#endif /* CONFIG_LAST_STAGE_INIT */
	359
	360
	361	#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
	362	void ft_board_setup(void blob, bd_t bd)
	363	{
	364	ft_cpu_setup(blob, bd);
	365	ft_blob_update(blob, bd);
	366	}
	367	#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */