[people/ms/u-boot.git] / doc / README.mpc85xxads

Motorola MPC8540ADS and MPC8560ADS board

Created 10/15/03 Xianghua Xiao
Updated 13-July-2004 Jon Loeliger
-----------------------------------------

0. Toolchain

    The Binutils in current ELDK toolchain will not support MPC85xx
    chip.  You need to use binutils-2.14.tar.bz2 (or newer) from
    http://ftp.gnu.org/gnu/binutils.

    The 8540/8560 ADS code base is known to compile using:
	gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)


1. SWITCH SETTINGS & JUMPERS

1.0 Nomenclature

    For some reason, the HW designers describe the switch settings
    in terms of 0 and 1, and then map that to physical switches where
    the label "On" refers to logic 0 and "Off" (unlabeled) is logic 1.
    Luckily, we're SW types and virtual settings are handled daily.

    The switches for the Rev A board are numbered differently than
    for the Pilot board.  Oh yeah.

    Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
    bits may contribute to signals that are numbered based at 0,
    and some of those signals may be high-bit-number-0 too.  Heed
    well the names and labels and do not get confused.

    "Off" == 1
    "On"  == 0

    SW18 is switch 18 as silk-screened onto the board.
    SW4[8] is the bit labled 8 on Switch 4.
    SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2
    SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3

1.1 For the MPC85xxADS Pilot Board

    First, make sure the board default setting is consistent with the document
    shipped with your board. Then apply the following changes:
    SW3[1-6]="all OFF"	(boot from 32bit flash, no boot sequence is used)
    SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
    SW11[2]='OFF for 8560, ON for 8540' (toggle 8540.8560 mode)
    SW11[7]='ON' (rev2), 'OFF' (rev1)
    SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
    SW22[1-4]="OFF OFF ON OFF"
    SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
    J1 = "Enable Prog" (Make sure your flash is programmable for development)

    If you want to test PCI functionality with a 33Mhz PCI card, you will
    have to change the system clock from the default 66Mhz to 33Mhz by
    setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
    double your platform clock(SW6) because the system clock is now only
    half of its original value. For example, if at 66MHz your system
    clock showed SW6[0:1] = 01, then at 33MHz SW6[0:1] it should be 10.

	SW17[8] ------+	   SW6
	SW15[1] ----+ |	  [0:1]
		    V V	   V V
	33MHz	    1 1	   1 0
	66MHz	    0 0	   0 1

    Hmmm... That SW6 setting description is incomplete but it works.


1.3 For the MPC85xxADS Rev A Board

    As shipped, the board should be a 33MHz PCI bus with a CPU Clock
    rate of 825 +/- fuzz:

	Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC:	82 MHz

    For 33MHz PCI, the switch settings should be like this:

	SW18[7:1] = 0100001 = M==33 =>	  33MHz
	SW18[8]	  =	  1	    => PWD Divider == 16
	SW16[1:2] =	 11	    => N == 16 as PWD==1

    Use the magical formula:
	Fout (MHz) = 16 * M / N = 16 * 33 / 16 = 33 MHz

	SW7[1:4]  =    1010 = 10    => 10 x 33	 = 330	CCB Sysclk
	SW7[5:6]  =	 01	    => 5:2 x 330 = 825	Core clock


    For 66MHz PCI, the switch settings should be like this:

	SW18[7:1] = 0100001 = M==33 =>	  33MHz
	SW18[8]	  =	  0	    => PWD Divider == 1
	SW16[1:2] =	 01	    => N == 8 as PWD == 0

    Use the magical formula:
	Fout (MHz) = 16 * M / N = 16 * 33 / 8 = 66 MHz

	SW7[1:4]  =    0101 =  5    => 5 x 66	 = 330	CCB Sysclk
	SW7[5:6]  =	 01	    => 5:2 x 330 = 825	Core clock


2. MEMORY MAP TO WORK WITH LINUX KERNEL

2.1. For the initial bringup, we adopted a consistent memory scheme
     between u-boot and linux kernel, you can customize it based on your
     system requirements:

     0x0000_0000     0x7fff_ffff     DDR		     2G
     0x8000_0000     0x9fff_ffff     PCI MEM		     512M
     0xc000_0000     0xdfff_ffff     Rapid IO		     512M
     0xe000_0000     0xe00f_ffff     CCSR		     1M
     0xe200_0000     0xe2ff_ffff     PCI IO		     16M
     0xf000_0000     0xf7ff_ffff     SDRAM		     128M
     0xf800_0000     0xf80f_ffff     BCSR		     1M
     0xff00_0000     0xffff_ffff     FLASH (boot bank)	     16M

2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. You
    can download them from linuxppc-2.4 public source. Please make sure the
    kernel's ppcboot.h is consistent with U-Boot's u-boot.h. You can use two
    default configuration files as your starting points to configure the
    kernel:
	arch/ppc/configs/mpc8540_ads_defconfig
	arch/ppc/configs/mpc8560_ads_defconfig

3. DEFINITIONS AND COMPILATION

3.1 Explanation on NEW definitions in:
	include/configs/MPC8540ADS.h
	include/configs/MPC8560ADS.h

    CONFIG_BOOKE	    BOOKE(e.g. Motorola MPC85xx, AMCC 440, etc)
    CONFIG_E500		    BOOKE e500 family(Motorola)
    CONFIG_MPC85xx	    MPC8540,MPC8560 and their derivatives
    CONFIG_MPC8540	    MPC8540 specific
    CONFIG_MPC8540ADS	    MPC8540ADS board specific
    CONFIG_MPC8560ADS	    MPC8560ADS board specific
    CONFIG_TSEC_ENET	    Use on-chip 10/100/1000 ethernet for networking
    CONFIG_SPD_EEPROM	    Use SPD EEPROM for DDR auto configuration, you can
			    also manual config the DDR after undef this
			    definition.
    CONFIG_DDR_ECC	    only for ECC DDR module
    CONFIG_DDR_DLL	    DLL fix on some ADS boards needed for more
			    stability.
    CONFIG_HAS_FEC	    If an FEC is on chip, set to 1, else 0.

Other than the above definitions, the rest in the config files are
straightforward.


3.2 Compilation

    Assuming you're using BASH shell:

	export CROSS_COMPILE=your-cross-compile-prefix
	cd u-boot
	make distclean
	make MPC8560ADS_config (or make MPC8540ADS_config)
	make

4.  Notes:

4.1 When connecting with kermit, the following commands must be present.in
    your .kermrc file. These are especially important when booting as
    MPC8560, as the serial console will not work without them:

	set speed 115200
	set carrier-watch off
	set handshake none
	set flow-control none
	robust


4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC
    ethernet. If that happens, you can try the following steps to make
    network work:

	MPC8560ADS>tftp 1000000 pImage
	(if it hangs, use Ctrl-C to quit)
	MPC8560ADS>nm fdf24524
	>0
	>1
	>. (to quit this memory operation)
	MPC8560ADS>tftp 1000000 pImage

4.3 If you're one of the early developers using the Rev1 8540/8560 chips,
    please use U-Boot 1.0.0, as the newer silicon will only support Rev2
    and future revisions of 8540/8560.


4.4 Reflash U-boot Image using U-boot

    tftp 10000 u-boot.bin
    protect off fff80000 ffffffff
    erase fff80000 ffffffff
    cp.b 10000 fff80000 80000


4.5 Reflash U-Boot with a BDI-2000

    BDI> erase 0xFFF80000 0x4000 0x20
    BDI> prog 0xfff80000 u-boot.bin.8560ads
    BDI> verify


5. Screen dump MPC8540ADS board

U-Boot 1.1.2(pq3-20040707-0) (Jul  6 2004 - 17:34:25)

Freescale PowerPC
    Core: E500, Version: 2.0, (0x80200020)
    System: 8540, Version: 2.0, (0x80300020)
    Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC:  82 MHz
    L1 D-cache 32KB, L1 I-cache 32KB enabled.
Board: ADS
    PCI1: 32 bit, 66 MHz (compiled)
I2C:   ready
DRAM:  Initializing
    SDRAM: 64 MB
    DDR: 256 MB
FLASH: 16 MB
L2 cache enabled: 256KB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   MOTO ENET0: PHY is Marvell 88E1011S (1410c62)
MOTO ENET1: PHY is Marvell 88E1011S (1410c62)
MOTO ENET2: PHY is Davicom DM9161E (181b881)
MOTO ENET0, MOTO ENET1, MOTO ENET2
Hit any key to stop autoboot:  0
=>
=> fli

Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
  Size: 16 MB in 64 Sectors
  Sector Start Addresses:
    FF000000	  FF040000	FF080000      FF0C0000	    FF100000
    FF140000	  FF180000	FF1C0000      FF200000	    FF240000
    FF280000	  FF2C0000	FF300000      FF340000	    FF380000
    FF3C0000	  FF400000	FF440000      FF480000	    FF4C0000
    FF500000	  FF540000	FF580000      FF5C0000	    FF600000
    FF640000	  FF680000	FF6C0000      FF700000	    FF740000
    FF780000	  FF7C0000	FF800000      FF840000	    FF880000
    FF8C0000	  FF900000	FF940000      FF980000	    FF9C0000
    FFA00000	  FFA40000	FFA80000      FFAC0000	    FFB00000
    FFB40000	  FFB80000	FFBC0000      FFC00000	    FFC40000
    FFC80000	  FFCC0000	FFD00000      FFD40000	    FFD80000
    FFDC0000	  FFE00000	FFE40000      FFE80000	    FFEC0000
    FFF00000	  FFF40000	FFF80000 (RO) FFFC0000 (RO)

=> bdinfo
memstart    = 0x00000000
memsize	    = 0x10000000
flashstart  = 0xFF000000
flashsize   = 0x01000000
flashoffset = 0x00000000
sramstart   = 0x00000000
sramsize    = 0x00000000
immr_base   = 0xE0000000
bootflags   = 0xE4013F80
intfreq	    =	 825 MHz
busfreq	    =	 330 MHz
ethaddr	    = 00:E0:0C:00:00:FD
eth1addr    = 00:E0:0C:00:01:FD
eth2addr    = 00:E0:0C:00:02:FD
IP addr	    = 192.168.1.253
baudrate    = 115200 bps


=> printenv
bootcmd=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;bootm $loadaddr $ramdiskaddr
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
bootdelay=10
baudrate=115200
loads_echo=1
ethaddr=00:E0:0C:00:00:FD
eth1addr=00:E0:0C:00:01:FD
eth2addr=00:E0:0C:00:02:FD
ipaddr=192.168.1.253
serverip=192.168.1.1
rootpath=/nfsroot
gatewayip=192.168.1.1
netmask=255.255.255.0
hostname=unknown
bootfile=your.uImage
loadaddr=200000
netdev=eth0
consoledev=ttyS0
ramdiskaddr=400000
ramdiskfile=your.ramdisk.u-boot
stdin=serial
stdout=serial
stderr=serial
ethact=MOTO ENET0

Environment size: 1020/8188 bytes
Commit	Line	Data
42d1f039 WD	1	Motorola MPC8540ADS and MPC8560ADS board
42d1f039 WD	2
9aea9530 WD	3	Created 10/15/03 Xianghua Xiao
9aea9530 WD	4	Updated 13-July-2004 Jon Loeliger
42d1f039 WD	5	-----------------------------------------
42d1f039 WD	6
4654af27	7	0. Toolchain
9aea9530 WD	8
9aea9530 WD	9	The Binutils in current ELDK toolchain will not support MPC85xx
03f5c550	10	chip. You need to use binutils-2.14.tar.bz2 (or newer) from
9aea9530 WD	11	http://ftp.gnu.org/gnu/binutils.
	12
	13	The 8540/8560 ADS code base is known to compile using:
	14	gcc (GCC) 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a)
	15
4654af27	16
42d1f039	17	1. SWITCH SETTINGS & JUMPERS
48abe7bf	18
9aea9530 WD	19	1.0 Nomenclature
	20
	21	For some reason, the HW designers describe the switch settings
	22	in terms of 0 and 1, and then map that to physical switches where
	23	the label "On" refers to logic 0 and "Off" (unlabeled) is logic 1.
	24	Luckily, we're SW types and virtual settings are handled daily.
	25
	26	The switches for the Rev A board are numbered differently than
	27	for the Pilot board. Oh yeah.
	28
	29	Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
	30	bits may contribute to signals that are numbered based at 0,
	31	and some of those signals may be high-bit-number-0 too. Heed
	32	well the names and labels and do not get confused.
	33
	34	"Off" == 1
	35	"On" == 0
	36
	37	SW18 is switch 18 as silk-screened onto the board.
	38	SW4[8] is the bit labled 8 on Switch 4.
	39	SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2
	40	SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3
	41
	42	1.1 For the MPC85xxADS Pilot Board
	43
	44	First, make sure the board default setting is consistent with the document
42d1f039	45	shipped with your board. Then apply the following changes:
9aea9530	46	SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used)
42d1f039	47	SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
0ac6f8b7	48	SW11[2]='OFF for 8560, ON for 8540' (toggle 8540.8560 mode)
547b4cb2	49	SW11[7]='ON' (rev2), 'OFF' (rev1)
42d1f039 WD	50	SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
	51	SW22[1-4]="OFF OFF ON OFF"
	52	SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
	53	J1 = "Enable Prog" (Make sure your flash is programmable for development)
48abe7bf	54
9aea9530	55	If you want to test PCI functionality with a 33Mhz PCI card, you will
547b4cb2 WD	56	have to change the system clock from the default 66Mhz to 33Mhz by
	57	setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
	58	double your platform clock(SW6) because the system clock is now only
0ac6f8b7 WD	59	half of its original value. For example, if at 66MHz your system
0ac6f8b7 WD	60	clock showed SW6[0:1] = 01, then at 33MHz SW6[0:1] it should be 10.
48abe7bf	61
9aea9530 WD	62	SW17[8] ------+ SW6
	63	SW15[1] ----+ \| [0:1]
	64	V V V V
	65	33MHz 1 1 1 0
	66	66MHz 0 0 0 1
	67
	68	Hmmm... That SW6 setting description is incomplete but it works.
	69
	70
	71	1.3 For the MPC85xxADS Rev A Board
	72
	73	As shipped, the board should be a 33MHz PCI bus with a CPU Clock
	74	rate of 825 +/- fuzz:
	75
	76	Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC: 82 MHz
	77
	78	For 33MHz PCI, the switch settings should be like this:
	79
	80	SW18[7:1] = 0100001 = M==33 => 33MHz
	81	SW18[8] = 1 => PWD Divider == 16
	82	SW16[1:2] = 11 => N == 16 as PWD==1
	83
	84	Use the magical formula:
	85	Fout (MHz) = 16 * M / N = 16 * 33 / 16 = 33 MHz
	86
	87	SW7[1:4] = 1010 = 10 => 10 x 33 = 330 CCB Sysclk
	88	SW7[5:6] = 01 => 5:2 x 330 = 825 Core clock
	89
	90
	91	For 66MHz PCI, the switch settings should be like this:
	92
	93	SW18[7:1] = 0100001 = M==33 => 33MHz
	94	SW18[8] = 0 => PWD Divider == 1
	95	SW16[1:2] = 01 => N == 8 as PWD == 0
	96
	97	Use the magical formula:
	98	Fout (MHz) = 16 * M / N = 16 * 33 / 8 = 66 MHz
	99
	100	SW7[1:4] = 0101 = 5 => 5 x 66 = 330 CCB Sysclk
	101	SW7[5:6] = 01 => 5:2 x 330 = 825 Core clock
547b4cb2	102
42d1f039 WD	103
42d1f039 WD	104	2. MEMORY MAP TO WORK WITH LINUX KERNEL
547b4cb2 WD	105
	106	2.1. For the initial bringup, we adopted a consistent memory scheme
	107	between u-boot and linux kernel, you can customize it based on your
	108	system requirements:
	109
9aea9530 WD	110	0x0000_0000 0x7fff_ffff DDR 2G
	111	0x8000_0000 0x9fff_ffff PCI MEM 512M
	112	0xc000_0000 0xdfff_ffff Rapid IO 512M
	113	0xe000_0000 0xe00f_ffff CCSR 1M
	114	0xe200_0000 0xe2ff_ffff PCI IO 16M
	115	0xf000_0000 0xf7ff_ffff SDRAM 128M
	116	0xf800_0000 0xf80f_ffff BCSR 1M
	117	0xff00_0000 0xffff_ffff FLASH (boot bank) 16M
547b4cb2 WD	118
	119	2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. You
	120	can download them from linuxppc-2.4 public source. Please make sure the
	121	kernel's ppcboot.h is consistent with U-Boot's u-boot.h. You can use two
	122	default configuration files as your starting points to configure the
	123	kernel:
	124	arch/ppc/configs/mpc8540_ads_defconfig
	125	arch/ppc/configs/mpc8560_ads_defconfig
42d1f039 WD	126
42d1f039 WD	127	3. DEFINITIONS AND COMPILATION
48abe7bf	128
0ac6f8b7 WD	129	3.1 Explanation on NEW definitions in:
	130	include/configs/MPC8540ADS.h
	131	include/configs/MPC8560ADS.h
	132
0c8721a4	133	CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, AMCC 440, etc)
9aea9530 WD	134	CONFIG_E500 BOOKE e500 family(Motorola)
	135	CONFIG_MPC85xx MPC8540,MPC8560 and their derivatives
	136	CONFIG_MPC8540 MPC8540 specific
9aea9530 WD	137	CONFIG_MPC8540ADS MPC8540ADS board specific
	138	CONFIG_MPC8560ADS MPC8560ADS board specific
	139	CONFIG_TSEC_ENET Use on-chip 10/100/1000 ethernet for networking
	140	CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can
	141	also manual config the DDR after undef this
0ac6f8b7	142	definition.
9aea9530 WD	143	CONFIG_DDR_ECC only for ECC DDR module
9aea9530 WD	144	CONFIG_DDR_DLL DLL fix on some ADS boards needed for more
0ac6f8b7	145	stability.
d9b94f28	146	CONFIG_HAS_FEC If an FEC is on chip, set to 1, else 0.
0ac6f8b7 WD	147
	148	Other than the above definitions, the rest in the config files are
	149	straightforward.
	150
42d1f039	151
42d1f039	152	3.2 Compilation
42d1f039	153
0ac6f8b7 WD	154	Assuming you're using BASH shell:
	155
	156	export CROSS_COMPILE=your-cross-compile-prefix
	157	cd u-boot
	158	make distclean
	159	make MPC8560ADS_config (or make MPC8540ADS_config)
	160	make
48abe7bf	161
547b4cb2	162	4. Notes:
48abe7bf	163
547b4cb2	164	4.1 When connecting with kermit, the following commands must be present.in
0ac6f8b7 WD	165	your .kermrc file. These are especially important when booting as
	166	MPC8560, as the serial console will not work without them:
	167
	168	set speed 115200
	169	set carrier-watch off
	170	set handshake none
	171	set flow-control none
	172	robust
	173
	174
	175	4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC
	176	ethernet. If that happens, you can try the following steps to make
	177	network work:
	178
	179	MPC8560ADS>tftp 1000000 pImage
	180	(if it hangs, use Ctrl-C to quit)
	181	MPC8560ADS>nm fdf24524
	182	>0
	183	>1
	184	>. (to quit this memory operation)
	185	MPC8560ADS>tftp 1000000 pImage
	186
	187	4.3 If you're one of the early developers using the Rev1 8540/8560 chips,
	188	please use U-Boot 1.0.0, as the newer silicon will only support Rev2
	189	and future revisions of 8540/8560.
	190
547b4cb2 WD	191
	192	4.4 Reflash U-boot Image using U-boot
	193
d9b94f28 JL	194	tftp 10000 u-boot.bin
	195	protect off fff80000 ffffffff
	196	erase fff80000 ffffffff
	197	cp.b 10000 fff80000 80000
547b4cb2	198
42d1f039	199
0ac6f8b7	200	4.5 Reflash U-Boot with a BDI-2000
48abe7bf	201
9aea9530	202	BDI> erase 0xFFF80000 0x4000 0x20
0ac6f8b7 WD	203	BDI> prog 0xfff80000 u-boot.bin.8560ads
	204	BDI> verify
	205
	206
9aea9530	207	5. Screen dump MPC8540ADS board
42d1f039	208
9aea9530 WD	209	U-Boot 1.1.2(pq3-20040707-0) (Jul 6 2004 - 17:34:25)
	210
	211	Freescale PowerPC
	212	Core: E500, Version: 2.0, (0x80200020)
	213	System: 8540, Version: 2.0, (0x80300020)
	214	Clocks: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC: 82 MHz
	215	L1 D-cache 32KB, L1 I-cache 32KB enabled.
	216	Board: ADS
	217	PCI1: 32 bit, 66 MHz (compiled)
42d1f039	218	I2C: ready
9aea9530 WD	219	DRAM: Initializing
	220	SDRAM: 64 MB
	221	DDR: 256 MB
42d1f039 WD	222	FLASH: 16 MB
	223	L2 cache enabled: 256KB
	224	*** Warning - bad CRC, using default environment
	225
	226	In: serial
	227	Out: serial
	228	Err: serial
9aea9530 WD	229	Net: MOTO ENET0: PHY is Marvell 88E1011S (1410c62)
	230	MOTO ENET1: PHY is Marvell 88E1011S (1410c62)
	231	MOTO ENET2: PHY is Davicom DM9161E (181b881)
	232	MOTO ENET0, MOTO ENET1, MOTO ENET2
42d1f039	233	Hit any key to stop autoboot: 0
9aea9530 WD	234	=>
9aea9530 WD	235	=> fli
42d1f039 WD	236
	237	Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K)
	238	Size: 16 MB in 64 Sectors
	239	Sector Start Addresses:
9aea9530 WD	240	FF000000 FF040000 FF080000 FF0C0000 FF100000
	241	FF140000 FF180000 FF1C0000 FF200000 FF240000
	242	FF280000 FF2C0000 FF300000 FF340000 FF380000
	243	FF3C0000 FF400000 FF440000 FF480000 FF4C0000
	244	FF500000 FF540000 FF580000 FF5C0000 FF600000
	245	FF640000 FF680000 FF6C0000 FF700000 FF740000
	246	FF780000 FF7C0000 FF800000 FF840000 FF880000
	247	FF8C0000 FF900000 FF940000 FF980000 FF9C0000
	248	FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000
	249	FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000
	250	FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000
	251	FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000
	252	FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO)
	253
	254	=> bdinfo
42d1f039	255	memstart = 0x00000000
9aea9530	256	memsize = 0x10000000
42d1f039 WD	257	flashstart = 0xFF000000
	258	flashsize = 0x01000000
	259	flashoffset = 0x00000000
	260	sramstart = 0x00000000
	261	sramsize = 0x00000000
9aea9530 WD	262	immr_base = 0xE0000000
	263	bootflags = 0xE4013F80
	264	intfreq = 825 MHz
	265	busfreq = 330 MHz
	266	ethaddr = 00:E0:0C:00:00:FD
	267	eth1addr = 00:E0:0C:00:01:FD
	268	eth2addr = 00:E0:0C:00:02:FD
	269	IP addr = 192.168.1.253
42d1f039	270	baudrate = 115200 bps
42d1f039	271
42d1f039	272
9aea9530 WD	273	=> printenv
	274	bootcmd=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
	275	ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;bootm $loadaddr $ramdiskaddr
	276	nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;bootm $loadaddr
	277	bootdelay=10
42d1f039 WD	278	baudrate=115200
42d1f039 WD	279	loads_echo=1
9aea9530 WD	280	ethaddr=00:E0:0C:00:00:FD
	281	eth1addr=00:E0:0C:00:01:FD
	282	eth2addr=00:E0:0C:00:02:FD
	283	ipaddr=192.168.1.253
	284	serverip=192.168.1.1
	285	rootpath=/nfsroot
	286	gatewayip=192.168.1.1
	287	netmask=255.255.255.0
	288	hostname=unknown
	289	bootfile=your.uImage
	290	loadaddr=200000
	291	netdev=eth0
	292	consoledev=ttyS0
	293	ramdiskaddr=400000
	294	ramdiskfile=your.ramdisk.u-boot
42d1f039 WD	295	stdin=serial
	296	stdout=serial
	297	stderr=serial
9aea9530	298	ethact=MOTO ENET0
42d1f039	299
9aea9530	300	Environment size: 1020/8188 bytes