[people/ms/u-boot.git] / doc / README.serial_multi

The support for multiple serial interfaces as implemented is mainly
intended to allow for modem dial-in / dial-out while still being able
to use a serial console on a (different) serial port.

MPC8XX Specific
===============
At the moment, the ports must be split on a SMC and a SCC port  on  a
8xx processor; other configurations are not (yet) supported.

Support for hardware handshake has not been implemented yet (but is
in the works).

*) The default console depends on the keys pressed:
	- SMC if keys not pressed (modem not enabled)
	- SCC if keys pressed (modem enabled)

*) The console can be switched to SCC by any of the following commands:

	setenv stdout serial_scc
	setenv stdin serial_scc
	setenv stderr serial_scc

*) The console can be switched to SMC by any of the following commands:

	setenv stdout serial_smc
	setenv stdin serial_smc
	setenv stderr serial_smc

*) If a file descriptor is set to "serial" then the current serial device
will be used which, in turn, can be switched by above commands.

*) The baudrate is the same for all serial devices. But it can be switched
just after switching the console:

	setenv sout serial_scc; setenv baudrate 38400

After that press 'enter' at the SCC console. Note that baudrates <38400
are not allowed on LWMON with watchdog enabled (see CONFIG_SYS_BAUDRATE_TABLE in
include/configs/lwmon.h).


PPC4XX Specific
===============
*) The default console is UART0

*) The console can be switched to UART1 by any of the following commands:
	setenv stdout serial1
	setenv stderr serial1
	setenv stdin serial1

*) The console can be switched to UART0 by any of the following commands:
	setenv stdout serial0
	setenv stderr serial0
	setenv stdin serial0
Commit	Line	Data
281e00a3 WD	1	The support for multiple serial interfaces as implemented is mainly
	2	intended to allow for modem dial-in / dial-out while still being able
	3	to use a serial console on a (different) serial port.
	4
ff36fd85 WD	5	MPC8XX Specific
ff36fd85 WD	6	===============
281e00a3 WD	7	At the moment, the ports must be split on a SMC and a SCC port on a
	8	8xx processor; other configurations are not (yet) supported.
	9
	10	Support for hardware handshake has not been implemented yet (but is
	11	in the works).
	12
	13	*) The default console depends on the keys pressed:
	14	- SMC if keys not pressed (modem not enabled)
	15	- SCC if keys pressed (modem enabled)
	16
	17	*) The console can be switched to SCC by any of the following commands:
	18
	19	setenv stdout serial_scc
	20	setenv stdin serial_scc
	21	setenv stderr serial_scc
	22
	23	*) The console can be switched to SMC by any of the following commands:
	24
	25	setenv stdout serial_smc
	26	setenv stdin serial_smc
	27	setenv stderr serial_smc
	28
	29	*) If a file descriptor is set to "serial" then the current serial device
	30	will be used which, in turn, can be switched by above commands.
	31
	32	*) The baudrate is the same for all serial devices. But it can be switched
	33	just after switching the console:
	34
	35	setenv sout serial_scc; setenv baudrate 38400
	36
	37	After that press 'enter' at the SCC console. Note that baudrates <38400
6d0f6bcf	38	are not allowed on LWMON with watchdog enabled (see CONFIG_SYS_BAUDRATE_TABLE in
281e00a3	39	include/configs/lwmon.h).
ff36fd85 WD	40
	41
	42	PPC4XX Specific
	43	===============
	44	*) The default console is UART0
	45
	46	*) The console can be switched to UART1 by any of the following commands:
	47	setenv stdout serial1
	48	setenv stderr serial1
	49	setenv stdin serial1
	50
	51	*) The console can be switched to UART0 by any of the following commands:
	52	setenv stdout serial0
	53	setenv stderr serial0
	54	setenv stdin serial0