]>
Commit | Line | Data |
---|---|---|
f31dac4e IR |
1 | # |
2 | # Boot count configuration | |
3 | # | |
4 | ||
c1e1c1ec | 5 | menuconfig BOOTCOUNT_LIMIT |
d1ec9461 LM |
6 | bool "Enable support for checking boot count limit" |
7 | help | |
8 | Enable checking for exceeding the boot count limit. | |
9 | More information: http://www.denx.de/wiki/DULG/UBootBootCountLimit | |
10 | ||
3dccc10e | 11 | if BOOTCOUNT_LIMIT |
f31dac4e | 12 | |
c1e1c1ec AK |
13 | choice |
14 | prompt "Boot count device" | |
c35e2d91 | 15 | default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX |
bec8c647 | 16 | default BOOTCOUNT_AT91 if AT91SAM9XE |
aa5a8632 AK |
17 | default BOOTCOUNT_GENERIC |
18 | ||
19 | config BOOTCOUNT_GENERIC | |
20 | bool "Generic default boot counter" | |
21 | help | |
22 | Generic bootcount stored at SYS_BOOTCOUNT_ADDR. | |
23 | ||
24 | SYS_BOOTCOUNT_ADDR: | |
25 | Set to the address where the bootcount and bootcount magic | |
26 | will be stored. | |
c1e1c1ec | 27 | |
f31dac4e IR |
28 | config BOOTCOUNT_EXT |
29 | bool "Boot counter on EXT filesystem" | |
30 | help | |
31 | Add support for maintaining boot count in a file on an EXT | |
32 | filesystem. | |
33 | ||
c35e2d91 AK |
34 | config BOOTCOUNT_AM33XX |
35 | bool "Boot counter in AM33XX RTC IP block" | |
36 | depends on AM33XX || SOC_DA8XX | |
37 | help | |
38 | A bootcount driver for the RTC IP block found on many TI platforms. | |
39 | This requires the RTC clocks, etc, to be enabled prior to use and | |
40 | not all boards with this IP block on it will have the RTC in use. | |
41 | ||
04c96ed2 AK |
42 | config BOOTCOUNT_ENV |
43 | bool "Boot counter in environment" | |
44 | help | |
45 | If no softreset save registers are found on the hardware | |
46 | "bootcount" is stored in the environment. To prevent a | |
47 | saveenv on all reboots, the environment variable | |
48 | "upgrade_available" is used. If "upgrade_available" is | |
49 | 0, "bootcount" is always 0, if "upgrade_available" is | |
50 | 1 "bootcount" is incremented in the environment. | |
51 | So the Userspace Application must set the "upgrade_available" | |
52 | and "bootcount" variable to 0, if a boot was successfully. | |
53 | ||
ff5410d3 AK |
54 | config BOOTCOUNT_RAM |
55 | bool "Boot counter in RAM" | |
56 | help | |
57 | Store the bootcount in DRAM protected against against bit errors | |
58 | due to short power loss or holding a system in RESET. | |
59 | ||
6cdd70eb AK |
60 | config BOOTCOUNT_I2C |
61 | bool "Boot counter on I2C device" | |
62 | help | |
63 | Enable support for the bootcounter on an i2c (like RTC) device. | |
64 | CONFIG_SYS_I2C_RTC_ADDR = i2c chip address | |
65 | CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for | |
66 | the bootcounter. | |
6cdd70eb | 67 | |
bec8c647 AK |
68 | config BOOTCOUNT_AT91 |
69 | bool "Boot counter for Atmel AT91SAM9XE" | |
70 | depends on AT91SAM9XE | |
71 | ||
c1e1c1ec AK |
72 | endchoice |
73 | ||
4bc4f8a6 AK |
74 | config BOOTCOUNT_ALEN |
75 | int "I2C address length" | |
76 | default 1 | |
77 | depends on BOOTCOUNT_I2C | |
78 | help | |
79 | Length of the the I2C address at SYS_BOOTCOUNT_ADDR for storing | |
80 | the boot counter. | |
81 | ||
c1e1c1ec AK |
82 | config SYS_BOOTCOUNT_SINGLEWORD |
83 | bool "Use single word to pack boot count and magic value" | |
aa5a8632 | 84 | depends on BOOTCOUNT_GENERIC |
c1e1c1ec AK |
85 | help |
86 | This option enables packing boot count magic value and boot count | |
87 | into single word (32 bits). | |
f31dac4e IR |
88 | |
89 | config SYS_BOOTCOUNT_EXT_INTERFACE | |
90 | string "Interface on which to find boot counter EXT filesystem" | |
91 | default "mmc" | |
92 | depends on BOOTCOUNT_EXT | |
93 | help | |
94 | Set the interface to use when locating the filesystem to use for the | |
95 | boot counter. | |
96 | ||
97 | config SYS_BOOTCOUNT_EXT_DEVPART | |
98 | string "Partition of the boot counter EXT filesystem" | |
99 | default "0:1" | |
100 | depends on BOOTCOUNT_EXT | |
101 | help | |
102 | Set the partition to use when locating the filesystem to use for the | |
103 | boot counter. | |
104 | ||
105 | config SYS_BOOTCOUNT_EXT_NAME | |
106 | string "Path and filename of the EXT filesystem based boot counter" | |
107 | default "/boot/failures" | |
108 | depends on BOOTCOUNT_EXT | |
109 | help | |
110 | Set the filename and path of the file used to store the boot counter. | |
111 | ||
112 | config SYS_BOOTCOUNT_ADDR | |
113 | hex "RAM address used for reading and writing the boot counter" | |
39bcbb77 TR |
114 | default 0x44E3E000 if BOOTCOUNT_AM33XX |
115 | default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A | |
116 | depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \ | |
117 | BOOTCOUNT_I2C | |
f31dac4e IR |
118 | help |
119 | Set the address used for reading and writing the boot counter. | |
120 | ||
121 | endif |