[people/ms/u-boot.git] / drivers / misc / ds4510.c

/*
 * Copyright 2008 Extreme Engineering Solutions, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0
 */

/*
 * Driver for DS4510, a CPU supervisor with integrated EEPROM, SRAM,
 * and 4 programmable non-volatile GPIO pins.
 */

#include <common.h>
#include <i2c.h>
#include <command.h>
#include "ds4510.h"

enum {
	DS4510_CMD_INFO,
	DS4510_CMD_DEVICE,
	DS4510_CMD_NV,
	DS4510_CMD_RSTDELAY,
	DS4510_CMD_OUTPUT,
	DS4510_CMD_INPUT,
	DS4510_CMD_PULLUP,
	DS4510_CMD_EEPROM,
	DS4510_CMD_SEEPROM,
	DS4510_CMD_SRAM,
};

/*
 * Write to DS4510, taking page boundaries into account
 */
static int ds4510_mem_write(uint8_t chip, int offset, uint8_t *buf, int count)
{
	int wrlen;
	int i = 0;

	do {
		wrlen = DS4510_EEPROM_PAGE_SIZE -
			DS4510_EEPROM_PAGE_OFFSET(offset);
		if (count < wrlen)
			wrlen = count;
		if (i2c_write(chip, offset, 1, &buf[i], wrlen))
			return -1;

		/*
		 * This delay isn't needed for SRAM writes but shouldn't delay
		 * things too much, so do it unconditionally for simplicity
		 */
		udelay(DS4510_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
		count -= wrlen;
		offset += wrlen;
		i += wrlen;
	} while (count > 0);

	return 0;
}

/*
 * General read from DS4510
 */
static int ds4510_mem_read(uint8_t chip, int offset, uint8_t *buf, int count)
{
	return i2c_read(chip, offset, 1, buf, count);
}

/*
 * Write SEE bit in config register.
 * nv = 0 - Writes to SEEPROM registers behave like EEPROM
 * nv = 1 - Writes to SEEPROM registers behave like SRAM
 */
static int ds4510_see_write(uint8_t chip, uint8_t nv)
{
	uint8_t data;

	if (i2c_read(chip, DS4510_CFG, 1, &data, 1))
		return -1;

	if (nv)	/* Treat SEEPROM bits as EEPROM */
		data &= ~DS4510_CFG_SEE;
	else	/* Treat SEEPROM bits as SRAM */
		data |= DS4510_CFG_SEE;

	return ds4510_mem_write(chip, DS4510_CFG, &data, 1);
}

/*
 * Write de-assertion of reset signal delay
 */
static int ds4510_rstdelay_write(uint8_t chip, uint8_t delay)
{
	uint8_t data;

	if (i2c_read(chip, DS4510_RSTDELAY, 1, &data, 1))
		return -1;

	data &= ~DS4510_RSTDELAY_MASK;
	data |= delay & DS4510_RSTDELAY_MASK;

	return ds4510_mem_write(chip, DS4510_RSTDELAY, &data, 1);
}

/*
 * Write pullup characteristics of IO pins
 */
static int ds4510_pullup_write(uint8_t chip, uint8_t val)
{
	val &= DS4510_IO_MASK;

	return ds4510_mem_write(chip, DS4510_PULLUP, (uint8_t *)&val, 1);
}

/*
 * Read pullup characteristics of IO pins
 */
static int ds4510_pullup_read(uint8_t chip)
{
	uint8_t val;

	if (i2c_read(chip, DS4510_PULLUP, 1, &val, 1))
		return -1;

	return val & DS4510_IO_MASK;
}

/*
 * Write drive level of IO pins
 */
static int ds4510_gpio_write(uint8_t chip, uint8_t val)
{
	uint8_t data;
	int i;

	for (i = 0; i < DS4510_NUM_IO; i++) {
		if (i2c_read(chip, DS4510_IO0 - i, 1, &data, 1))
			return -1;

		if (val & (0x1 << i))
			data |= 0x1;
		else
			data &= ~0x1;

		if (ds4510_mem_write(chip, DS4510_IO0 - i, &data, 1))
			return -1;
	}

	return 0;
}

/*
 * Read drive level of IO pins
 */
static int ds4510_gpio_read(uint8_t chip)
{
	uint8_t data;
	int val = 0;
	int i;

	for (i = 0; i < DS4510_NUM_IO; i++) {
		if (i2c_read(chip, DS4510_IO0 - i, 1, &data, 1))
			return -1;

		if (data & 1)
			val |= (1 << i);
	}

	return val;
}

/*
 * Read physical level of IO pins
 */
static int ds4510_gpio_read_val(uint8_t chip)
{
	uint8_t val;

	if (i2c_read(chip, DS4510_IO_STATUS, 1, &val, 1))
		return -1;

	return val & DS4510_IO_MASK;
}

/*
 * Display DS4510 information
 */
static int ds4510_info(uint8_t chip)
{
	int i;
	int tmp;
	uint8_t data;

	printf("DS4510 @ 0x%x:\n\n", chip);

	if (i2c_read(chip, DS4510_RSTDELAY, 1, &data, 1))
		return -1;
	printf("rstdelay = 0x%x\n\n", data & DS4510_RSTDELAY_MASK);

	if (i2c_read(chip, DS4510_CFG, 1, &data, 1))
		return -1;
	printf("config   = 0x%x\n", data);
	printf(" /ready  = %d\n", data & DS4510_CFG_READY ? 1 : 0);
	printf(" trip pt = %d\n", data & DS4510_CFG_TRIP_POINT ? 1 : 0);
	printf(" rst sts = %d\n", data & DS4510_CFG_RESET ? 1 : 0);
	printf(" /see    = %d\n", data & DS4510_CFG_SEE ? 1 : 0);
	printf(" swrst   = %d\n\n", data & DS4510_CFG_SWRST ? 1 : 0);

	printf("gpio pins: 3210\n");
	printf("---------------\n");
	printf("pullup     ");

	tmp = ds4510_pullup_read(chip);
	if (tmp == -1)
		return tmp;
	for (i = DS4510_NUM_IO - 1; i >= 0; i--)
		printf("%d", (tmp & (1 << i)) ? 1 : 0);
	printf("\n");

	printf("driven     ");
	tmp = ds4510_gpio_read(chip);
	if (tmp == -1)
		return -1;
	for (i = DS4510_NUM_IO - 1; i >= 0; i--)
		printf("%d", (tmp & (1 << i)) ? 1 : 0);
	printf("\n");

	printf("read       ");
	tmp = ds4510_gpio_read_val(chip);
	if (tmp == -1)
		return -1;
	for (i = DS4510_NUM_IO - 1; i >= 0; i--)
		printf("%d", (tmp & (1 << i)) ? 1 : 0);
	printf("\n");

	return 0;
}

cmd_tbl_t cmd_ds4510[] = {
	U_BOOT_CMD_MKENT(device, 3, 0, (void *)DS4510_CMD_DEVICE, "", ""),
	U_BOOT_CMD_MKENT(nv, 3, 0, (void *)DS4510_CMD_NV, "", ""),
	U_BOOT_CMD_MKENT(output, 4, 0, (void *)DS4510_CMD_OUTPUT, "", ""),
	U_BOOT_CMD_MKENT(input, 3, 0, (void *)DS4510_CMD_INPUT, "", ""),
	U_BOOT_CMD_MKENT(pullup, 4, 0, (void *)DS4510_CMD_PULLUP, "", ""),
	U_BOOT_CMD_MKENT(info, 2, 0, (void *)DS4510_CMD_INFO, "", ""),
	U_BOOT_CMD_MKENT(rstdelay, 3, 0, (void *)DS4510_CMD_RSTDELAY, "", ""),
	U_BOOT_CMD_MKENT(eeprom, 6, 0, (void *)DS4510_CMD_EEPROM, "", ""),
	U_BOOT_CMD_MKENT(seeprom, 6, 0, (void *)DS4510_CMD_SEEPROM, "", ""),
	U_BOOT_CMD_MKENT(sram, 6, 0, (void *)DS4510_CMD_SRAM, "", ""),
};

int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
	static uint8_t chip = 0x51;
	cmd_tbl_t *c;
	ulong ul_arg2 = 0;
	ulong ul_arg3 = 0;
	int tmp;
	ulong addr;
	ulong off;
	ulong cnt;
	int end;
	int (*rw_func)(uint8_t, int, uint8_t *, int);

	c = find_cmd_tbl(argv[1], cmd_ds4510, ARRAY_SIZE(cmd_ds4510));

	/* All commands but "device" require 'maxargs' arguments */
	if (!c || !((argc == (c->maxargs)) ||
		(((int)c->cmd == DS4510_CMD_DEVICE) &&
		 (argc == (c->maxargs - 1))))) {
		return cmd_usage(cmdtp);
	}

	/* arg2 used as chip addr and pin number */
	if (argc > 2)
		ul_arg2 = simple_strtoul(argv[2], NULL, 16);

	/* arg3 used as output/pullup value */
	if (argc > 3)
		ul_arg3 = simple_strtoul(argv[3], NULL, 16);

	switch ((int)c->cmd) {
	case DS4510_CMD_DEVICE:
		if (argc == 3)
			chip = ul_arg2;
		printf("Current device address: 0x%x\n", chip);
		return 0;
	case DS4510_CMD_NV:
		return ds4510_see_write(chip, ul_arg2);
	case DS4510_CMD_OUTPUT:
		tmp = ds4510_gpio_read(chip);
		if (tmp == -1)
			return -1;
		if (ul_arg3)
			tmp |= (1 << ul_arg2);
		else
			tmp &= ~(1 << ul_arg2);
		return ds4510_gpio_write(chip, tmp);
	case DS4510_CMD_INPUT:
		tmp = ds4510_gpio_read_val(chip);
		if (tmp == -1)
			return -1;
		return (tmp & (1 << ul_arg2)) != 0;
	case DS4510_CMD_PULLUP:
		tmp = ds4510_pullup_read(chip);
		if (tmp == -1)
			return -1;
		if (ul_arg3)
			tmp |= (1 << ul_arg2);
		else
			tmp &= ~(1 << ul_arg2);
		return ds4510_pullup_write(chip, tmp);
	case DS4510_CMD_INFO:
		return ds4510_info(chip);
	case DS4510_CMD_RSTDELAY:
		return ds4510_rstdelay_write(chip, ul_arg2);
	case DS4510_CMD_EEPROM:
		end = DS4510_EEPROM + DS4510_EEPROM_SIZE;
		off = DS4510_EEPROM;
		break;
	case DS4510_CMD_SEEPROM:
		end = DS4510_SEEPROM + DS4510_SEEPROM_SIZE;
		off = DS4510_SEEPROM;
		break;
	case DS4510_CMD_SRAM:
		end = DS4510_SRAM + DS4510_SRAM_SIZE;
		off = DS4510_SRAM;
		break;
	default:
		/* We should never get here... */
		return 1;
	}

	/* Only eeprom, seeprom, and sram commands should make it here */
	if (strcmp(argv[2], "read") == 0)
		rw_func = ds4510_mem_read;
	else if (strcmp(argv[2], "write") == 0)
		rw_func = ds4510_mem_write;
	else
		return cmd_usage(cmdtp);

	addr = simple_strtoul(argv[3], NULL, 16);
	off += simple_strtoul(argv[4], NULL, 16);
	cnt = simple_strtoul(argv[5], NULL, 16);

	if ((off + cnt) > end) {
		printf("ERROR: invalid len\n");
		return -1;
	}

	return rw_func(chip, off, (uint8_t *)addr, cnt);
}

U_BOOT_CMD(
	ds4510,	6,	1,	do_ds4510,
	"ds4510 eeprom/seeprom/sram/gpio access",
	"device [dev]\n"
	"	- show or set current device address\n"
	"ds4510 info\n"
	"	- display ds4510 info\n"
	"ds4510 output pin 0|1\n"
	"	- set pin low or high-Z\n"
	"ds4510 input pin\n"
	"	- read value of pin\n"
	"ds4510 pullup pin 0|1\n"
	"	- disable/enable pullup on specified pin\n"
	"ds4510 nv 0|1\n"
	"	- make gpio and seeprom writes volatile/non-volatile"
	"\n"
	"ds4510 rstdelay 0-3\n"
	"	- set reset output delay"
	"\n"
	"ds4510 eeprom read addr off cnt\n"
	"ds4510 eeprom write addr off cnt\n"
	"	- read/write 'cnt' bytes at EEPROM offset 'off'\n"
	"ds4510 seeprom read addr off cnt\n"
	"ds4510 seeprom write addr off cnt\n"
	"	- read/write 'cnt' bytes at SRAM-shadowed EEPROM offset 'off'\n"
	"ds4510 sram read addr off cnt\n"
	"ds4510 sram write addr off cnt\n"
	"	- read/write 'cnt' bytes at SRAM offset 'off'"
);
Commit	Line	Data
a7c93104 PT	1	/*
	2	* Copyright 2008 Extreme Engineering Solutions, Inc.
	3	*
5b8031cc	4	* SPDX-License-Identifier: GPL-2.0
a7c93104 PT	5	*/
	6
	7	/*
	8	* Driver for DS4510, a CPU supervisor with integrated EEPROM, SRAM,
	9	* and 4 programmable non-volatile GPIO pins.
	10	*/
	11
	12	#include <common.h>
	13	#include <i2c.h>
	14	#include <command.h>
1136eb5e	15	#include "ds4510.h"
a7c93104	16
a7c93104 PT	17	enum {
	18	DS4510_CMD_INFO,
	19	DS4510_CMD_DEVICE,
	20	DS4510_CMD_NV,
	21	DS4510_CMD_RSTDELAY,
	22	DS4510_CMD_OUTPUT,
	23	DS4510_CMD_INPUT,
	24	DS4510_CMD_PULLUP,
	25	DS4510_CMD_EEPROM,
	26	DS4510_CMD_SEEPROM,
	27	DS4510_CMD_SRAM,
	28	};
	29
	30	/*
	31	* Write to DS4510, taking page boundaries into account
	32	*/
1136eb5e	33	static int ds4510_mem_write(uint8_t chip, int offset, uint8_t *buf, int count)
a7c93104 PT	34	{
	35	int wrlen;
	36	int i = 0;
	37
	38	do {
	39	wrlen = DS4510_EEPROM_PAGE_SIZE -
	40	DS4510_EEPROM_PAGE_OFFSET(offset);
	41	if (count < wrlen)
	42	wrlen = count;
	43	if (i2c_write(chip, offset, 1, &buf[i], wrlen))
	44	return -1;
	45
	46	/*
	47	* This delay isn't needed for SRAM writes but shouldn't delay
	48	* things too much, so do it unconditionally for simplicity
	49	*/
	50	udelay(DS4510_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
	51	count -= wrlen;
	52	offset += wrlen;
	53	i += wrlen;
	54	} while (count > 0);
	55
	56	return 0;
	57	}
	58
	59	/*
	60	* General read from DS4510
	61	*/
1136eb5e	62	static int ds4510_mem_read(uint8_t chip, int offset, uint8_t *buf, int count)
a7c93104 PT	63	{
	64	return i2c_read(chip, offset, 1, buf, count);
	65	}
	66
	67	/*
	68	* Write SEE bit in config register.
	69	* nv = 0 - Writes to SEEPROM registers behave like EEPROM
	70	* nv = 1 - Writes to SEEPROM registers behave like SRAM
	71	*/
1136eb5e	72	static int ds4510_see_write(uint8_t chip, uint8_t nv)
a7c93104 PT	73	{
	74	uint8_t data;
	75
	76	if (i2c_read(chip, DS4510_CFG, 1, &data, 1))
	77	return -1;
	78
	79	if (nv) /* Treat SEEPROM bits as EEPROM */
	80	data &= ~DS4510_CFG_SEE;
	81	else /* Treat SEEPROM bits as SRAM */
	82	data \|= DS4510_CFG_SEE;
	83
	84	return ds4510_mem_write(chip, DS4510_CFG, &data, 1);
	85	}
	86
	87	/*
	88	* Write de-assertion of reset signal delay
	89	*/
1136eb5e	90	static int ds4510_rstdelay_write(uint8_t chip, uint8_t delay)
a7c93104 PT	91	{
	92	uint8_t data;
	93
	94	if (i2c_read(chip, DS4510_RSTDELAY, 1, &data, 1))
	95	return -1;
	96
	97	data &= ~DS4510_RSTDELAY_MASK;
	98	data \|= delay & DS4510_RSTDELAY_MASK;
	99
	100	return ds4510_mem_write(chip, DS4510_RSTDELAY, &data, 1);
	101	}
	102
	103	/*
	104	* Write pullup characteristics of IO pins
	105	*/
1136eb5e	106	static int ds4510_pullup_write(uint8_t chip, uint8_t val)
a7c93104 PT	107	{
	108	val &= DS4510_IO_MASK;
	109
	110	return ds4510_mem_write(chip, DS4510_PULLUP, (uint8_t *)&val, 1);
	111	}
	112
	113	/*
	114	* Read pullup characteristics of IO pins
	115	*/
1136eb5e	116	static int ds4510_pullup_read(uint8_t chip)
a7c93104 PT	117	{
	118	uint8_t val;
	119
	120	if (i2c_read(chip, DS4510_PULLUP, 1, &val, 1))
	121	return -1;
	122
	123	return val & DS4510_IO_MASK;
	124	}
	125
	126	/*
	127	* Write drive level of IO pins
	128	*/
1136eb5e	129	static int ds4510_gpio_write(uint8_t chip, uint8_t val)
a7c93104 PT	130	{
	131	uint8_t data;
	132	int i;
	133
	134	for (i = 0; i < DS4510_NUM_IO; i++) {
	135	if (i2c_read(chip, DS4510_IO0 - i, 1, &data, 1))
	136	return -1;
	137
	138	if (val & (0x1 << i))
	139	data \|= 0x1;
	140	else
	141	data &= ~0x1;
	142
	143	if (ds4510_mem_write(chip, DS4510_IO0 - i, &data, 1))
	144	return -1;
	145	}
	146
	147	return 0;
	148	}
	149
	150	/*
	151	* Read drive level of IO pins
	152	*/
1136eb5e	153	static int ds4510_gpio_read(uint8_t chip)
a7c93104 PT	154	{
	155	uint8_t data;
	156	int val = 0;
	157	int i;
	158
	159	for (i = 0; i < DS4510_NUM_IO; i++) {
	160	if (i2c_read(chip, DS4510_IO0 - i, 1, &data, 1))
	161	return -1;
	162
	163	if (data & 1)
	164	val \|= (1 << i);
	165	}
	166
	167	return val;
	168	}
	169
	170	/*
	171	* Read physical level of IO pins
	172	*/
1136eb5e	173	static int ds4510_gpio_read_val(uint8_t chip)
a7c93104 PT	174	{
	175	uint8_t val;
	176
	177	if (i2c_read(chip, DS4510_IO_STATUS, 1, &val, 1))
	178	return -1;
	179
	180	return val & DS4510_IO_MASK;
	181	}
	182
a7c93104 PT	183	/*
	184	* Display DS4510 information
	185	*/
	186	static int ds4510_info(uint8_t chip)
	187	{
	188	int i;
	189	int tmp;
	190	uint8_t data;
	191
	192	printf("DS4510 @ 0x%x:\n\n", chip);
	193
	194	if (i2c_read(chip, DS4510_RSTDELAY, 1, &data, 1))
	195	return -1;
	196	printf("rstdelay = 0x%x\n\n", data & DS4510_RSTDELAY_MASK);
	197
	198	if (i2c_read(chip, DS4510_CFG, 1, &data, 1))
	199	return -1;
	200	printf("config = 0x%x\n", data);
	201	printf(" /ready = %d\n", data & DS4510_CFG_READY ? 1 : 0);
	202	printf(" trip pt = %d\n", data & DS4510_CFG_TRIP_POINT ? 1 : 0);
	203	printf(" rst sts = %d\n", data & DS4510_CFG_RESET ? 1 : 0);
	204	printf(" /see = %d\n", data & DS4510_CFG_SEE ? 1 : 0);
	205	printf(" swrst = %d\n\n", data & DS4510_CFG_SWRST ? 1 : 0);
	206
	207	printf("gpio pins: 3210\n");
	208	printf("---------------\n");
	209	printf("pullup ");
	210
	211	tmp = ds4510_pullup_read(chip);
	212	if (tmp == -1)
	213	return tmp;
	214	for (i = DS4510_NUM_IO - 1; i >= 0; i--)
	215	printf("%d", (tmp & (1 << i)) ? 1 : 0);
	216	printf("\n");
	217
	218	printf("driven ");
	219	tmp = ds4510_gpio_read(chip);
	220	if (tmp == -1)
	221	return -1;
	222	for (i = DS4510_NUM_IO - 1; i >= 0; i--)
	223	printf("%d", (tmp & (1 << i)) ? 1 : 0);
	224	printf("\n");
	225
	226	printf("read ");
	227	tmp = ds4510_gpio_read_val(chip);
	228	if (tmp == -1)
	229	return -1;
	230	for (i = DS4510_NUM_IO - 1; i >= 0; i--)
	231	printf("%d", (tmp & (1 << i)) ? 1 : 0);
	232	printf("\n");
	233
	234	return 0;
	235	}
a7c93104 PT	236
	237	cmd_tbl_t cmd_ds4510[] = {
	238	U_BOOT_CMD_MKENT(device, 3, 0, (void *)DS4510_CMD_DEVICE, "", ""),
	239	U_BOOT_CMD_MKENT(nv, 3, 0, (void *)DS4510_CMD_NV, "", ""),
	240	U_BOOT_CMD_MKENT(output, 4, 0, (void *)DS4510_CMD_OUTPUT, "", ""),
	241	U_BOOT_CMD_MKENT(input, 3, 0, (void *)DS4510_CMD_INPUT, "", ""),
	242	U_BOOT_CMD_MKENT(pullup, 4, 0, (void *)DS4510_CMD_PULLUP, "", ""),
a7c93104	243	U_BOOT_CMD_MKENT(info, 2, 0, (void *)DS4510_CMD_INFO, "", ""),
a7c93104	244	U_BOOT_CMD_MKENT(rstdelay, 3, 0, (void *)DS4510_CMD_RSTDELAY, "", ""),
a7c93104 PT	245	U_BOOT_CMD_MKENT(eeprom, 6, 0, (void *)DS4510_CMD_EEPROM, "", ""),
	246	U_BOOT_CMD_MKENT(seeprom, 6, 0, (void *)DS4510_CMD_SEEPROM, "", ""),
	247	U_BOOT_CMD_MKENT(sram, 6, 0, (void *)DS4510_CMD_SRAM, "", ""),
a7c93104 PT	248	};
a7c93104 PT	249
54841ab5	250	int do_ds4510(cmd_tbl_t cmdtp, int flag, int argc, char const argv[])
a7c93104	251	{
21c72979	252	static uint8_t chip = 0x51;
a7c93104 PT	253	cmd_tbl_t *c;
	254	ulong ul_arg2 = 0;
	255	ulong ul_arg3 = 0;
	256	int tmp;
a7c93104 PT	257	ulong addr;
	258	ulong off;
	259	ulong cnt;
	260	int end;
	261	int (rw_func)(uint8_t, int, uint8_t , int);
a7c93104 PT	262
	263	c = find_cmd_tbl(argv[1], cmd_ds4510, ARRAY_SIZE(cmd_ds4510));
	264
	265	/* All commands but "device" require 'maxargs' arguments */
	266	if (!c \|\| !((argc == (c->maxargs)) \|\|
	267	(((int)c->cmd == DS4510_CMD_DEVICE) &&
	268	(argc == (c->maxargs - 1))))) {
47e26b1b	269	return cmd_usage(cmdtp);
a7c93104 PT	270	}
	271
	272	/* arg2 used as chip addr and pin number */
	273	if (argc > 2)
	274	ul_arg2 = simple_strtoul(argv[2], NULL, 16);
	275
	276	/* arg3 used as output/pullup value */
	277	if (argc > 3)
	278	ul_arg3 = simple_strtoul(argv[3], NULL, 16);
	279
	280	switch ((int)c->cmd) {
	281	case DS4510_CMD_DEVICE:
	282	if (argc == 3)
	283	chip = ul_arg2;
	284	printf("Current device address: 0x%x\n", chip);
	285	return 0;
	286	case DS4510_CMD_NV:
	287	return ds4510_see_write(chip, ul_arg2);
	288	case DS4510_CMD_OUTPUT:
	289	tmp = ds4510_gpio_read(chip);
	290	if (tmp == -1)
	291	return -1;
	292	if (ul_arg3)
	293	tmp \|= (1 << ul_arg2);
	294	else
	295	tmp &= ~(1 << ul_arg2);
	296	return ds4510_gpio_write(chip, tmp);
	297	case DS4510_CMD_INPUT:
	298	tmp = ds4510_gpio_read_val(chip);
	299	if (tmp == -1)
	300	return -1;
	301	return (tmp & (1 << ul_arg2)) != 0;
	302	case DS4510_CMD_PULLUP:
	303	tmp = ds4510_pullup_read(chip);
	304	if (tmp == -1)
	305	return -1;
	306	if (ul_arg3)
	307	tmp \|= (1 << ul_arg2);
	308	else
	309	tmp &= ~(1 << ul_arg2);
	310	return ds4510_pullup_write(chip, tmp);
a7c93104 PT	311	case DS4510_CMD_INFO:
a7c93104 PT	312	return ds4510_info(chip);
a7c93104 PT	313	case DS4510_CMD_RSTDELAY:
a7c93104 PT	314	return ds4510_rstdelay_write(chip, ul_arg2);
a7c93104 PT	315	case DS4510_CMD_EEPROM:
	316	end = DS4510_EEPROM + DS4510_EEPROM_SIZE;
	317	off = DS4510_EEPROM;
	318	break;
	319	case DS4510_CMD_SEEPROM:
	320	end = DS4510_SEEPROM + DS4510_SEEPROM_SIZE;
	321	off = DS4510_SEEPROM;
	322	break;
	323	case DS4510_CMD_SRAM:
	324	end = DS4510_SRAM + DS4510_SRAM_SIZE;
	325	off = DS4510_SRAM;
	326	break;
a7c93104 PT	327	default:
	328	/* We should never get here... */
	329	return 1;
	330	}
	331
a7c93104	332	/* Only eeprom, seeprom, and sram commands should make it here */
47e26b1b	333	if (strcmp(argv[2], "read") == 0)
a7c93104	334	rw_func = ds4510_mem_read;
47e26b1b	335	else if (strcmp(argv[2], "write") == 0)
a7c93104	336	rw_func = ds4510_mem_write;
47e26b1b WD	337	else
47e26b1b WD	338	return cmd_usage(cmdtp);
a7c93104 PT	339
	340	addr = simple_strtoul(argv[3], NULL, 16);
	341	off += simple_strtoul(argv[4], NULL, 16);
	342	cnt = simple_strtoul(argv[5], NULL, 16);
	343
	344	if ((off + cnt) > end) {
	345	printf("ERROR: invalid len\n");
	346	return -1;
	347	}
	348
	349	return rw_func(chip, off, (uint8_t *)addr, cnt);
a7c93104 PT	350	}
	351
	352	U_BOOT_CMD(
	353	ds4510, 6, 1, do_ds4510,
2fb2604d	354	"ds4510 eeprom/seeprom/sram/gpio access",
a7c93104 PT	355	"device [dev]\n"
a7c93104 PT	356	" - show or set current device address\n"
a7c93104 PT	357	"ds4510 info\n"
a7c93104 PT	358	" - display ds4510 info\n"
a7c93104 PT	359	"ds4510 output pin 0\|1\n"
	360	" - set pin low or high-Z\n"
	361	"ds4510 input pin\n"
	362	" - read value of pin\n"
	363	"ds4510 pullup pin 0\|1\n"
	364	" - disable/enable pullup on specified pin\n"
	365	"ds4510 nv 0\|1\n"
a89c33db	366	" - make gpio and seeprom writes volatile/non-volatile"
a89c33db	367	"\n"
a7c93104	368	"ds4510 rstdelay 0-3\n"
a89c33db	369	" - set reset output delay"
a89c33db	370	"\n"
a7c93104 PT	371	"ds4510 eeprom read addr off cnt\n"
	372	"ds4510 eeprom write addr off cnt\n"
	373	" - read/write 'cnt' bytes at EEPROM offset 'off'\n"
	374	"ds4510 seeprom read addr off cnt\n"
	375	"ds4510 seeprom write addr off cnt\n"
	376	" - read/write 'cnt' bytes at SRAM-shadowed EEPROM offset 'off'\n"
	377	"ds4510 sram read addr off cnt\n"
	378	"ds4510 sram write addr off cnt\n"
a89c33db	379	" - read/write 'cnt' bytes at SRAM offset 'off'"
a7c93104	380	);