[people/ms/u-boot.git] / drivers / serial / Kconfig

#
# Serial device configuration
#

menu "Serial drivers"

config REQUIRE_SERIAL_CONSOLE
	bool "Require a serial port for console"
	# Running without a serial console is not supported by the
	# non-dm serial code
	depends on DM_SERIAL
	default y
	help
	  Require a serial port for the console, and panic if none is found
	  during serial port initialization (default y). Set this to n on
	  boards which have no debug serial port whatsoever.

config SERIAL_PRESENT
	bool "Provide a serial driver"
	depends on DM_SERIAL
	default y
	help
	  In very space-constrained devices even the full UART driver is too
	  large. In this case the debug UART can still be used in some cases.
	  This option enables the full UART in U-Boot, so if is it disabled,
	  the full UART driver will be omitted, thus saving space.

config SPL_SERIAL_PRESENT
	bool "Provide a serial driver in SPL"
	depends on DM_SERIAL
	default y
	help
	  In very space-constrained devices even the full UART driver is too
	  large. In this case the debug UART can still be used in some cases.
	  This option enables the full UART in SPL, so if is it disabled,
	  the full UART driver will be omitted, thus saving space.

config DM_SERIAL
	bool "Enable Driver Model for serial drivers"
	depends on DM
	help
	  Enable driver model for serial. This replaces
	  drivers/serial/serial.c with the serial uclass, which
	  implements serial_putc() etc. The uclass interface is
	  defined in include/serial.h.

config DEBUG_UART
	bool "Enable an early debug UART for debugging"
	help
	  The debug UART is intended for use very early in U-Boot to debug
	  problems when an ICE or other debug mechanism is not available.

	  To use it you should:
	  - Make sure your UART supports this interface
	  - Enable CONFIG_DEBUG_UART
	  - Enable the CONFIG for your UART to tell it to provide this interface
	        (e.g. CONFIG_DEBUG_UART_NS16550)
	  - Define the required settings as needed (see below)
	  - Call debug_uart_init() before use
	  - Call debug_uart_putc() to output a character

	  Depending on your platform it may be possible to use this UART before
	  a stack is available.

	  If your UART does not support this interface you can probably add
	  support quite easily. Remember that you cannot use driver model and
	  it is preferred to use no stack.

	  You must not use this UART once driver model is working and the
	  serial drivers are up and running (done in serial_init()). Otherwise
	  the drivers may conflict and you will get strange output.

choice
	prompt "Select which UART will provide the debug UART"
	depends on DEBUG_UART
	default DEBUG_UART_NS16550

config DEBUG_UART_ALTERA_JTAGUART
	bool "Altera JTAG UART"
	help
	  Select this to enable a debug UART using the altera_jtag_uart driver.
	  You will need to provide parameters to make this work. The driver will
	  be available until the real driver model serial is running.

config DEBUG_UART_ALTERA_UART
	bool "Altera UART"
	help
	  Select this to enable a debug UART using the altera_uart driver.
	  You will need to provide parameters to make this work. The driver will
	  be available until the real driver model serial is running.

config DEBUG_UART_NS16550
	bool "ns16550"
	help
	  Select this to enable a debug UART using the ns16550 driver. You
	  will need to provide parameters to make this work. The driver will
	  be available until the real driver model serial is running.

config DEBUG_EFI_CONSOLE
	bool "EFI"
	depends on EFI_APP
	help
	  Select this to enable a debug console which calls back to EFI to
	  output to the console. This can be useful for early debugging of
	  U-Boot when running on top of EFI (Extensive Firmware Interface).
	  This is a type of BIOS used by PCs.

config DEBUG_UART_S5P
	bool "Samsung S5P"
	help
	  Select this to enable a debug UART using the serial_s5p driver. You
	  will need to provide parameters to make this work. The driver will
	  be available until the real driver-model serial is running.

config DEBUG_UART_UARTLITE
	bool "Xilinx Uartlite"
	help
	  Select this to enable a debug UART using the serial_uartlite driver.
	  You will need to provide parameters to make this work. The driver will
	  be available until the real driver-model serial is running.

config DEBUG_UART_ZYNQ
	bool "Xilinx Zynq"
	help
	  Select this to enable a debug UART using the serial_zynq driver. You
	  will need to provide parameters to make this work. The driver will
	  be available until the real driver-model serial is running.

config DEBUG_UART_APBUART
	depends on LEON3
	bool "Gaisler APBUART"
	help
	  Select this to enable a debug UART using the serial_leon3 driver. You
	  will need to provide parameters to make this work. The driver will
	  be available until the real driver model serial is running.

config DEBUG_UART_PL010
	bool "pl010"
	help
	  Select this to enable a debug UART using the pl01x driver with the
	  PL010 UART type. You will need to provide parameters to make this
	  work. The driver will be available until the real driver model
	  serial is running.

config DEBUG_UART_PL011
	bool "pl011"
	help
	  Select this to enable a debug UART using the pl01x driver with the
	  PL011 UART type. You will need to provide parameters to make this
	  work. The driver will be available until the real driver model
	  serial is running.

config DEBUG_UART_PIC32
	bool "Microchip PIC32"
	depends on PIC32_SERIAL
	help
	  Select this to enable a debug UART using the serial_pic32 driver. You
	  will need to provide parameters to make this work. The driver will
	  be available until the real driver model serial is running.

endchoice

config DEBUG_UART_BASE
	hex "Base address of UART"
	depends on DEBUG_UART
	help
	  This is the base address of your UART for memory-mapped UARTs.

	  A default should be provided by your board, but if not you will need
	  to use the correct value here.

config DEBUG_UART_CLOCK
	int "UART input clock"
	depends on DEBUG_UART
	help
	  The UART input clock determines the speed of the internal UART
	  circuitry. The baud rate is derived from this by dividing the input
	  clock down.

	  A default should be provided by your board, but if not you will need
	  to use the correct value here.

config DEBUG_UART_SHIFT
	int "UART register shift"
	depends on DEBUG_UART
	default 0 if DEBUG_UART
	help
	  Some UARTs (notably ns16550) support different register layouts
	  where the registers are spaced either as bytes, words or some other
	  value. Use this value to specify the shift to use, where 0=byte
	  registers, 2=32-bit word registers, etc.

config DEBUG_UART_BOARD_INIT
	bool "Enable board-specific debug UART init"
	depends on DEBUG_UART
	help
	  Some boards need to set things up before the debug UART can be used.
	  On these boards a call to debug_uart_init() is insufficient. When
	  this option is enabled, the function board_debug_uart_init() will
	  be called when debug_uart_init() is called. You can put any code
	  here that is needed to set up the UART ready for use, such as set
	  pin multiplexing or enable clocks.

config DEBUG_UART_ANNOUNCE
	bool "Show a message when the debug UART starts up"
	depends on DEBUG_UART
	help
	  Enable this option to show a message when the debug UART is ready
	  for use. You will see a message like "<debug_uart> " as soon as
	  U-Boot has the UART ready for use (i.e. your code calls
	  debug_uart_init()). This can be useful just as a check that
	  everything is working.

config DEBUG_UART_SKIP_INIT
	bool "Skip UART initialization"
	help
	  Select this if the UART you want to use for debug output is already
	  initialized by the time U-Boot starts its execution.

config ALTERA_JTAG_UART
	bool "Altera JTAG UART support"
	depends on DM_SERIAL
	help
	  Select this to enable an JTAG UART for Altera devices.The JTAG UART
	  core implements a method to communicate serial character streams
	  between a host PC and a Qsys system on an Altera FPGA. Please find
	  details on the "Embedded Peripherals IP User Guide" of Altera.

config ALTERA_JTAG_UART_BYPASS
	bool "Bypass output when no connection"
	depends on ALTERA_JTAG_UART
	help
	  Bypass console output and keep going even if there is no JTAG
	  terminal connection with the host. The console output will resume
	  once the JTAG terminal is connected. Without the bypass, the console
	  output will wait forever until a JTAG terminal is connected. If you
	  not are sure, say Y.

config ALTERA_UART
	bool "Altera UART support"
	depends on DM_SERIAL
	help
	  Select this to enable an UART for Altera devices. Please find
	  details on the "Embedded Peripherals IP User Guide" of Altera.

config FSL_LPUART
	bool "Freescale LPUART support"
	help
	  Select this to enable a Low Power UART for Freescale VF610 and
	  QorIQ Layerscape devices.

config PIC32_SERIAL
	bool "Support for Microchip PIC32 on-chip UART"
	depends on DM_SERIAL && MACH_PIC32
	default y
	help
	  Support for the UART found on Microchip PIC32 SoC's.

config SYS_NS16550
	bool "NS16550 UART or compatible"
	help
	  Support NS16550 UART or compatible. This can be enabled in the
	  device tree with the correct input clock frequency. If the input
	  clock frequency is not defined in the device tree, the macro
	  CONFIG_SYS_NS16550_CLK defined in a legacy board header file will
	  be used. It can be a constant or a function to get clock, eg,
	  get_serial_clock().

config SANDBOX_SERIAL
	bool "Sandbox UART support"
	depends on SANDBOX
	help
	  Select this to enable a seral UART for sandbox. This is required to
	  operate correctly, otherwise you will see no serial output from
	  sandbox. The emulated UART will display to the console and console
	  input will be fed into the UART. This allows you to interact with
	  U-Boot.

	  The operation of the console is controlled by the -t command-line
	  flag. In raw mode, U-Boot sees all characters from the terminal
	  before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
	  is processed by the terminal, and terminates U-Boot. Valid options
	  are:

	     -t raw-with-sigs	Raw mode, Ctrl-C will terminate U-Boot
	     -t raw		Raw mode, Ctrl-C is processed by U-Boot
	     -t cooked		Cooked mode, Ctrl-C terminates

config UNIPHIER_SERIAL
	bool "Support for UniPhier on-chip UART"
	depends on ARCH_UNIPHIER
	help
	  If you have a UniPhier based board and want to use the on-chip
	  serial ports, say Y to this option. If unsure, say N.

config XILINX_UARTLITE
	bool "Xilinx Uarlite support"
	depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || 4xx)
	help
	  If you have a Xilinx based board and want to use the uartlite
	  serial ports, say Y to this option. If unsure, say N.

endmenu
Commit	Line	Data
0b11dbf7 MY	1	#
	2	# Serial device configuration
	3	#
	4
	5	menu "Serial drivers"
	6
8c458588 HG	7	config REQUIRE_SERIAL_CONSOLE
	8	bool "Require a serial port for console"
	9	# Running without a serial console is not supported by the
	10	# non-dm serial code
	11	depends on DM_SERIAL
	12	default y
	13	help
	14	Require a serial port for the console, and panic if none is found
	15	during serial port initialization (default y). Set this to n on
	16	boards which have no debug serial port whatsoever.
	17
92c55b68 SG	18	config SERIAL_PRESENT
	19	bool "Provide a serial driver"
	20	depends on DM_SERIAL
	21	default y
	22	help
	23	In very space-constrained devices even the full UART driver is too
	24	large. In this case the debug UART can still be used in some cases.
	25	This option enables the full UART in U-Boot, so if is it disabled,
	26	the full UART driver will be omitted, thus saving space.
	27
	28	config SPL_SERIAL_PRESENT
	29	bool "Provide a serial driver in SPL"
	30	depends on DM_SERIAL
	31	default y
	32	help
	33	In very space-constrained devices even the full UART driver is too
	34	large. In this case the debug UART can still be used in some cases.
	35	This option enables the full UART in SPL, so if is it disabled,
	36	the full UART driver will be omitted, thus saving space.
	37
da333ae7 MY	38	config DM_SERIAL
	39	bool "Enable Driver Model for serial drivers"
	40	depends on DM
	41	help
f94a1bed SG	42	Enable driver model for serial. This replaces
	43	drivers/serial/serial.c with the serial uclass, which
	44	implements serial_putc() etc. The uclass interface is
	45	defined in include/serial.h.
ff247b7a	46
2f964aa7 SG	47	config DEBUG_UART
	48	bool "Enable an early debug UART for debugging"
	49	help
	50	The debug UART is intended for use very early in U-Boot to debug
	51	problems when an ICE or other debug mechanism is not available.
	52
	53	To use it you should:
	54	- Make sure your UART supports this interface
	55	- Enable CONFIG_DEBUG_UART
	56	- Enable the CONFIG for your UART to tell it to provide this interface
	57	(e.g. CONFIG_DEBUG_UART_NS16550)
	58	- Define the required settings as needed (see below)
	59	- Call debug_uart_init() before use
	60	- Call debug_uart_putc() to output a character
	61
	62	Depending on your platform it may be possible to use this UART before
	63	a stack is available.
	64
	65	If your UART does not support this interface you can probably add
	66	support quite easily. Remember that you cannot use driver model and
	67	it is preferred to use no stack.
	68
	69	You must not use this UART once driver model is working and the
	70	serial drivers are up and running (done in serial_init()). Otherwise
	71	the drivers may conflict and you will get strange output.
	72
21d00436 SG	73	choice
	74	prompt "Select which UART will provide the debug UART"
	75	depends on DEBUG_UART
b1e361b6	76	default DEBUG_UART_NS16550
21d00436	77
220e8021 TC	78	config DEBUG_UART_ALTERA_JTAGUART
	79	bool "Altera JTAG UART"
	80	help
	81	Select this to enable a debug UART using the altera_jtag_uart driver.
	82	You will need to provide parameters to make this work. The driver will
	83	be available until the real driver model serial is running.
	84
da2f838d TC	85	config DEBUG_UART_ALTERA_UART
	86	bool "Altera UART"
	87	help
	88	Select this to enable a debug UART using the altera_uart driver.
	89	You will need to provide parameters to make this work. The driver will
	90	be available until the real driver model serial is running.
	91
21d00436 SG	92	config DEBUG_UART_NS16550
	93	bool "ns16550"
	94	help
	95	Select this to enable a debug UART using the ns16550 driver. You
	96	will need to provide parameters to make this work. The driver will
	97	be available until the real driver model serial is running.
	98
275854ba SG	99	config DEBUG_EFI_CONSOLE
	100	bool "EFI"
	101	depends on EFI_APP
	102	help
	103	Select this to enable a debug console which calls back to EFI to
	104	output to the console. This can be useful for early debugging of
	105	U-Boot when running on top of EFI (Extensive Firmware Interface).
	106	This is a type of BIOS used by PCs.
	107
bf6e7022 SG	108	config DEBUG_UART_S5P
	109	bool "Samsung S5P"
	110	help
	111	Select this to enable a debug UART using the serial_s5p driver. You
	112	will need to provide parameters to make this work. The driver will
	113	be available until the real driver-model serial is running.
	114
4166ba3b MS	115	config DEBUG_UART_UARTLITE
	116	bool "Xilinx Uartlite"
	117	help
	118	Select this to enable a debug UART using the serial_uartlite driver.
	119	You will need to provide parameters to make this work. The driver will
	120	be available until the real driver-model serial is running.
	121
c54c0a4c SG	122	config DEBUG_UART_ZYNQ
	123	bool "Xilinx Zynq"
	124	help
6bf87dac	125	Select this to enable a debug UART using the serial_zynq driver. You
c54c0a4c SG	126	will need to provide parameters to make this work. The driver will
	127	be available until the real driver-model serial is running.
	128
e43ce3fc FR	129	config DEBUG_UART_APBUART
	130	depends on LEON3
	131	bool "Gaisler APBUART"
	132	help
	133	Select this to enable a debug UART using the serial_leon3 driver. You
	134	will need to provide parameters to make this work. The driver will
	135	be available until the real driver model serial is running.
	136
19de8150 ST	137	config DEBUG_UART_PL010
	138	bool "pl010"
	139	help
	140	Select this to enable a debug UART using the pl01x driver with the
	141	PL010 UART type. You will need to provide parameters to make this
	142	work. The driver will be available until the real driver model
	143	serial is running.
	144
	145	config DEBUG_UART_PL011
	146	bool "pl011"
	147	help
	148	Select this to enable a debug UART using the pl01x driver with the
	149	PL011 UART type. You will need to provide parameters to make this
	150	work. The driver will be available until the real driver model
	151	serial is running.
	152
9e160ee8 PT	153	config DEBUG_UART_PIC32
	154	bool "Microchip PIC32"
	155	depends on PIC32_SERIAL
	156	help
	157	Select this to enable a debug UART using the serial_pic32 driver. You
	158	will need to provide parameters to make this work. The driver will
	159	be available until the real driver model serial is running.
	160
21d00436 SG	161	endchoice
21d00436 SG	162
2f964aa7 SG	163	config DEBUG_UART_BASE
	164	hex "Base address of UART"
	165	depends on DEBUG_UART
	166	help
	167	This is the base address of your UART for memory-mapped UARTs.
	168
	169	A default should be provided by your board, but if not you will need
	170	to use the correct value here.
	171
	172	config DEBUG_UART_CLOCK
	173	int "UART input clock"
	174	depends on DEBUG_UART
	175	help
	176	The UART input clock determines the speed of the internal UART
	177	circuitry. The baud rate is derived from this by dividing the input
	178	clock down.
	179
	180	A default should be provided by your board, but if not you will need
	181	to use the correct value here.
	182
dd0b0122 SG	183	config DEBUG_UART_SHIFT
	184	int "UART register shift"
	185	depends on DEBUG_UART
	186	default 0 if DEBUG_UART
	187	help
	188	Some UARTs (notably ns16550) support different register layouts
	189	where the registers are spaced either as bytes, words or some other
	190	value. Use this value to specify the shift to use, where 0=byte
	191	registers, 2=32-bit word registers, etc.
	192
0e977bc1 SG	193	config DEBUG_UART_BOARD_INIT
	194	bool "Enable board-specific debug UART init"
	195	depends on DEBUG_UART
	196	help
	197	Some boards need to set things up before the debug UART can be used.
	198	On these boards a call to debug_uart_init() is insufficient. When
	199	this option is enabled, the function board_debug_uart_init() will
	200	be called when debug_uart_init() is called. You can put any code
	201	here that is needed to set up the UART ready for use, such as set
	202	pin multiplexing or enable clocks.
	203
c7fefcb9 SG	204	config DEBUG_UART_ANNOUNCE
	205	bool "Show a message when the debug UART starts up"
	206	depends on DEBUG_UART
	207	help
	208	Enable this option to show a message when the debug UART is ready
	209	for use. You will see a message like "<debug_uart> " as soon as
	210	U-Boot has the UART ready for use (i.e. your code calls
	211	debug_uart_init()). This can be useful just as a check that
	212	everything is working.
	213
19de8150 ST	214	config DEBUG_UART_SKIP_INIT
	215	bool "Skip UART initialization"
	216	help
	217	Select this if the UART you want to use for debug output is already
	218	initialized by the time U-Boot starts its execution.
	219
220e8021 TC	220	config ALTERA_JTAG_UART
	221	bool "Altera JTAG UART support"
	222	depends on DM_SERIAL
	223	help
	224	Select this to enable an JTAG UART for Altera devices.The JTAG UART
	225	core implements a method to communicate serial character streams
	226	between a host PC and a Qsys system on an Altera FPGA. Please find
	227	details on the "Embedded Peripherals IP User Guide" of Altera.
	228
	229	config ALTERA_JTAG_UART_BYPASS
	230	bool "Bypass output when no connection"
	231	depends on ALTERA_JTAG_UART
	232	help
	233	Bypass console output and keep going even if there is no JTAG
	234	terminal connection with the host. The console output will resume
	235	once the JTAG terminal is connected. Without the bypass, the console
	236	output will wait forever until a JTAG terminal is connected. If you
	237	not are sure, say Y.
	238
da2f838d TC	239	config ALTERA_UART
	240	bool "Altera UART support"
	241	depends on DM_SERIAL
	242	help
	243	Select this to enable an UART for Altera devices. Please find
	244	details on the "Embedded Peripherals IP User Guide" of Altera.
	245
5ed07cf5 BM	246	config FSL_LPUART
	247	bool "Freescale LPUART support"
	248	help
	249	Select this to enable a Low Power UART for Freescale VF610 and
	250	QorIQ Layerscape devices.
	251
9e160ee8 PT	252	config PIC32_SERIAL
	253	bool "Support for Microchip PIC32 on-chip UART"
	254	depends on DM_SERIAL && MACH_PIC32
	255	default y
	256	help
	257	Support for the UART found on Microchip PIC32 SoC's.
	258
9e39003e TC	259	config SYS_NS16550
	260	bool "NS16550 UART or compatible"
	261	help
	262	Support NS16550 UART or compatible. This can be enabled in the
	263	device tree with the correct input clock frequency. If the input
	264	clock frequency is not defined in the device tree, the macro
	265	CONFIG_SYS_NS16550_CLK defined in a legacy board header file will
	266	be used. It can be a constant or a function to get clock, eg,
	267	get_serial_clock().
	268
af282245 SG	269	config SANDBOX_SERIAL
af282245 SG	270	bool "Sandbox UART support"
2ea65f3e	271	depends on SANDBOX
af282245 SG	272	help
	273	Select this to enable a seral UART for sandbox. This is required to
	274	operate correctly, otherwise you will see no serial output from
	275	sandbox. The emulated UART will display to the console and console
	276	input will be fed into the UART. This allows you to interact with
	277	U-Boot.
	278
	279	The operation of the console is controlled by the -t command-line
	280	flag. In raw mode, U-Boot sees all characters from the terminal
	281	before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
	282	is processed by the terminal, and terminates U-Boot. Valid options
	283	are:
	284
	285	-t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot
	286	-t raw Raw mode, Ctrl-C is processed by U-Boot
	287	-t cooked Cooked mode, Ctrl-C terminates
	288
ff247b7a	289	config UNIPHIER_SERIAL
b6ef3a3f	290	bool "Support for UniPhier on-chip UART"
2ea65f3e	291	depends on ARCH_UNIPHIER
ff247b7a	292	help
b6ef3a3f MY	293	If you have a UniPhier based board and want to use the on-chip
b6ef3a3f MY	294	serial ports, say Y to this option. If unsure, say N.
dcfe4a54	295
54e24d33 MS	296	config XILINX_UARTLITE
54e24d33 MS	297	bool "Xilinx Uarlite support"
80cce262	298	depends on DM_SERIAL && (MICROBLAZE \|\| ARCH_ZYNQ \|\| ARCH_ZYNQMP \|\| 4xx)
54e24d33 MS	299	help
	300	If you have a Xilinx based board and want to use the uartlite
	301	serial ports, say Y to this option. If unsure, say N.
	302
0b11dbf7	303	endmenu