]>
Commit | Line | Data |
---|---|---|
46578cc0 SR |
1 | /* |
2 | * (C) Copyright 2000, 2001 | |
3 | * Wolfgang Denk, DENX Software Engineering, wd@denx.de. | |
4 | * | |
5 | * See file CREDITS for list of people who contributed to this | |
6 | * project. | |
7 | * | |
8 | * This program is free software; you can redistribute it and/or | |
9 | * modify it under the terms of the GNU General Public License as | |
10 | * published by the Free Software Foundation; either version 2 of | |
11 | * the License, or (at your option) any later version. | |
12 | * | |
13 | * This program is distributed in the hope that it will be useful, | |
14 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
15 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
16 | * GNU General Public License for more details. | |
17 | * | |
18 | * You should have received a copy of the GNU General Public License | |
19 | * along with this program; if not, write to the Free Software | |
20 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, | |
21 | * MA 02111-1307 USA | |
22 | */ | |
23 | ||
24 | /* | |
25 | * board/config.h - configuration options, board specific | |
26 | */ | |
27 | ||
28 | #ifndef __CONFIG_H | |
29 | #define __CONFIG_H | |
30 | ||
31 | /* Debug options */ | |
7a8e9bed | 32 | /*#define __DEBUG_START_FROM_SRAM__ */ |
46578cc0 SR |
33 | |
34 | ||
35 | ||
36 | /* | |
37 | * High Level Configuration Options | |
38 | * (easy to change) | |
39 | */ | |
40 | ||
41 | #define CONFIG_405EP 1 /* This is a PPC405 CPU */ | |
42 | #define CONFIG_4xx 1 /* ...member of PPC4xx family */ | |
43 | #define CONFIG_BUBINGA405EP 1 /* ...on a BUBINGA405EP board */ | |
44 | ||
45 | #define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ | |
46 | ||
47 | #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ | |
48 | ||
49 | #define CONFIG_NO_SERIAL_EEPROM | |
50 | /*#undef CONFIG_NO_SERIAL_EEPROM*/ | |
51 | /*----------------------------------------------------------------------------*/ | |
52 | /*----------------------------------------------------------------------------*/ | |
53 | /*----------------------------------------------------------------------------*/ | |
54 | #ifdef CONFIG_NO_SERIAL_EEPROM | |
55 | ||
56 | /* | |
57 | !------------------------------------------------------------------------------- | |
58 | ! Defines for entry options. | |
59 | ! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that | |
60 | ! are plugged in the board will be utilized as non-ECC DIMMs. | |
61 | !------------------------------------------------------------------------------- | |
62 | */ | |
63 | #define AUTO_MEMORY_CONFIG | |
64 | #define DIMM_READ_ADDR 0xAB | |
65 | #define DIMM_WRITE_ADDR 0xAA | |
66 | ||
67 | /* | |
68 | !------------------------------------------------------------------------------- | |
69 | ! PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI, | |
70 | ! assuming a 33MHz input clock to the 405EP from the C9531. | |
71 | !------------------------------------------------------------------------------- | |
72 | */ | |
73 | #define PLLMR0_DEFAULT PLLMR0_266_133_66 | |
74 | #define PLLMR1_DEFAULT PLLMR1_266_133_66 | |
75 | ||
76 | #endif | |
77 | /*----------------------------------------------------------------------------*/ | |
78 | /*----------------------------------------------------------------------------*/ | |
79 | /*----------------------------------------------------------------------------*/ | |
80 | ||
81 | /*#define CFG_ENV_IS_IN_FLASH 1*/ /* use FLASH for environment vars */ | |
82 | #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ | |
83 | ||
84 | #ifdef CFG_ENV_IS_IN_NVRAM | |
85 | #undef CFG_ENV_IS_IN_FLASH | |
86 | #else | |
87 | #ifdef CFG_ENV_IS_IN_FLASH | |
88 | #undef CFG_ENV_IS_IN_NVRAM | |
89 | #endif | |
90 | #endif | |
91 | ||
92 | #define CONFIG_BAUDRATE 115200 | |
93 | #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ | |
94 | ||
95 | #if 1 | |
96 | #define CONFIG_BOOTCOMMAND "" /* autoboot command */ | |
97 | #else | |
98 | #define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ | |
99 | #endif | |
100 | ||
101 | /* Size (bytes) of interrupt driven serial port buffer. | |
102 | * Set to 0 to use polling instead of interrupts. | |
103 | * Setting to 0 will also disable RTS/CTS handshaking. | |
104 | */ | |
105 | #if 0 | |
106 | #define CONFIG_SERIAL_SOFTWARE_FIFO 4000 | |
107 | #else | |
108 | #undef CONFIG_SERIAL_SOFTWARE_FIFO | |
109 | #endif | |
110 | ||
111 | #if 0 | |
112 | #define CONFIG_BOOTARGS "root=/dev/nfs " \ | |
113 | "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \ | |
114 | "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4" | |
115 | #else | |
116 | #define CONFIG_BOOTARGS "root=/dev/hda1 " \ | |
117 | "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0" | |
118 | ||
119 | #endif | |
120 | ||
121 | #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ | |
122 | #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ | |
123 | ||
124 | #define CONFIG_MII 1 /* MII PHY management */ | |
125 | #define CONFIG_PHY_ADDR 1 /* PHY address */ | |
126 | ||
127 | #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ | |
128 | ||
129 | /* | |
130 | #ifndef __DEBUG_START_FROM_SRAM__ | |
131 | #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ | |
132 | CFG_CMD_PCI | \ | |
133 | CFG_CMD_IRQ | \ | |
134 | CFG_CMD_KGDB | \ | |
135 | CFG_CMD_DHCP | \ | |
136 | CFG_CMD_DATE | \ | |
137 | CFG_CMD_BEDBUG | \ | |
138 | CFG_CMD_ELF ) | |
139 | #else | |
140 | #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ | |
141 | CFG_CMD_PCI | \ | |
142 | CFG_CMD_IRQ | \ | |
143 | CFG_CMD_KGDB | \ | |
144 | CFG_CMD_DHCP | \ | |
145 | CFG_CMD_DATE | \ | |
146 | CFG_CMD_DATE | \ | |
147 | CFG_CMD_ELF ) | |
148 | #endif | |
149 | */ | |
150 | ||
151 | #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ | |
152 | CFG_CMD_PCI | \ | |
153 | CFG_CMD_IRQ | \ | |
154 | CFG_CMD_KGDB | \ | |
155 | CFG_CMD_DHCP | \ | |
156 | CFG_CMD_DATE | \ | |
157 | CFG_CMD_DATE | \ | |
158 | CFG_CMD_ELF ) | |
159 | ||
160 | /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ | |
161 | #include <cmd_confdefs.h> | |
162 | ||
163 | #undef CONFIG_WATCHDOG /* watchdog disabled */ | |
164 | ||
165 | #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ | |
166 | ||
167 | /* | |
168 | * Miscellaneous configurable options | |
169 | */ | |
170 | #define CFG_LONGHELP /* undef to save memory */ | |
171 | #define CFG_PROMPT "=> " /* Monitor Command Prompt */ | |
172 | #if (CONFIG_COMMANDS & CFG_CMD_KGDB) | |
173 | #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ | |
174 | #else | |
175 | #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ | |
176 | #endif | |
177 | #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ | |
178 | #define CFG_MAXARGS 16 /* max number of command args */ | |
179 | #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ | |
180 | ||
181 | #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ | |
182 | #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ | |
183 | ||
184 | /* | |
185 | * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. | |
186 | * If CFG_405_UART_ERRATA_59, then UART divisor is 31. | |
187 | * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. | |
188 | * The Linux BASE_BAUD define should match this configuration. | |
189 | * baseBaud = cpuClock/(uartDivisor*16) | |
190 | * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock, | |
191 | * set Linux BASE_BAUD to 403200. | |
192 | */ | |
193 | #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ | |
194 | #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ | |
195 | #define CFG_BASE_BAUD 691200 | |
196 | ||
197 | /* The following table includes the supported baudrates */ | |
198 | #define CFG_BAUDRATE_TABLE \ | |
199 | {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} | |
200 | ||
201 | #define CFG_LOAD_ADDR 0x100000 /* default load address */ | |
202 | #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ | |
203 | ||
204 | #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ | |
205 | ||
206 | #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ | |
207 | #undef CONFIG_SOFT_I2C /* I2C bit-banged */ | |
208 | #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ | |
209 | #define CFG_I2C_SLAVE 0x7F | |
210 | ||
211 | ||
212 | /*----------------------------------------------------------------------- | |
213 | * PCI stuff | |
214 | *----------------------------------------------------------------------- | |
215 | */ | |
216 | #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ | |
217 | #define PCI_HOST_FORCE 1 /* configure as pci host */ | |
218 | #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ | |
219 | ||
220 | #define CONFIG_PCI /* include pci support */ | |
221 | #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ | |
222 | #define CONFIG_PCI_PNP /* do pci plug-and-play */ | |
223 | /* resource configuration */ | |
224 | ||
225 | #define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ | |
226 | #define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ | |
227 | #define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ | |
228 | #define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ | |
229 | #define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ | |
230 | #define CFG_PCI_PTM2LA 0x00000000 /* disabled */ | |
231 | #define CFG_PCI_PTM2MS 0x00000000 /* disabled */ | |
232 | #define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ | |
233 | ||
234 | /*----------------------------------------------------------------------- | |
235 | * External peripheral base address | |
236 | *----------------------------------------------------------------------- | |
237 | */ | |
238 | #undef CONFIG_IDE_LED /* no led for ide supported */ | |
239 | #undef CONFIG_IDE_RESET /* no reset for ide supported */ | |
240 | ||
241 | #define CFG_KEY_REG_BASE_ADDR 0xF0100000 | |
242 | #define CFG_IR_REG_BASE_ADDR 0xF0200000 | |
243 | #define CFG_FPGA_REG_BASE_ADDR 0xF0300000 | |
244 | ||
245 | /*----------------------------------------------------------------------- | |
246 | * Start addresses for the final memory configuration | |
247 | * (Set up by the startup code) | |
248 | * Please note that CFG_SDRAM_BASE _must_ start at 0 | |
249 | */ | |
250 | #define CFG_SDRAM_BASE 0x00000000 | |
251 | #ifdef __DEBUG_START_FROM_SRAM__ | |
252 | #define CFG_SRAM_BASE 0xFFF80000 | |
253 | #define CFG_FLASH_BASE 0xFFF00000 | |
254 | #define CFG_MONITOR_BASE CFG_SRAM_BASE | |
255 | #else | |
256 | #define CFG_SRAM_BASE 0xFFF00000 | |
257 | #define CFG_FLASH_BASE 0xFFF80000 | |
258 | #define CFG_MONITOR_BASE CFG_FLASH_BASE | |
259 | #endif | |
260 | ||
261 | ||
7a8e9bed | 262 | /*#define CFG_MONITOR_LEN (200 * 1024) /XXX* Reserve 200 kB for Monitor */ |
46578cc0 SR |
263 | #define CFG_MONITOR_LEN (192 * 1024) /* Reserve 200 kB for Monitor */ |
264 | #define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ | |
265 | ||
266 | /* | |
267 | * For booting Linux, the board info and command line data | |
268 | * have to be in the first 8 MB of memory, since this is | |
269 | * the maximum mapped by the Linux kernel during initialization. | |
270 | */ | |
271 | #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ | |
272 | /*----------------------------------------------------------------------- | |
273 | * FLASH organization | |
274 | */ | |
275 | #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ | |
276 | #define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ | |
277 | ||
278 | #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ | |
279 | #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ | |
280 | ||
281 | /* BEG ENVIRONNEMENT FLASH */ | |
282 | #ifdef CFG_ENV_IS_IN_FLASH | |
283 | #define CFG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */ | |
284 | #define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ | |
285 | #define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ | |
286 | #endif | |
287 | /* END ENVIRONNEMENT FLASH */ | |
288 | /*----------------------------------------------------------------------- | |
289 | * NVRAM organization | |
290 | */ | |
291 | #define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ | |
292 | #define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */ | |
293 | ||
294 | #ifdef CFG_ENV_IS_IN_NVRAM | |
295 | #define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */ | |
296 | #define CFG_ENV_ADDR \ | |
297 | (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ | |
298 | #endif | |
299 | /*----------------------------------------------------------------------- | |
300 | * Cache Configuration | |
301 | */ | |
302 | #define CFG_DCACHE_SIZE 16384 /* For IBM 405EP CPU */ | |
303 | #define CFG_CACHELINE_SIZE 32 /* ... */ | |
304 | #if (CONFIG_COMMANDS & CFG_CMD_KGDB) | |
305 | #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ | |
306 | #endif | |
307 | ||
308 | /* | |
309 | * Init Memory Controller: | |
310 | * | |
311 | * BR0/1 and OR0/1 (FLASH) | |
312 | */ | |
313 | ||
314 | #define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ | |
315 | #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ | |
316 | ||
317 | ||
318 | /* Configuration Port location */ | |
319 | #define CONFIG_PORT_ADDR 0xF0000500 | |
320 | ||
321 | /*----------------------------------------------------------------------- | |
322 | * Definitions for initial stack pointer and data area (in data cache) | |
323 | */ | |
324 | /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ | |
325 | #define CFG_TEMP_STACK_OCM 1 | |
326 | ||
327 | /* On Chip Memory location */ | |
328 | #define CFG_OCM_DATA_ADDR 0xF8000000 | |
329 | #define CFG_OCM_DATA_SIZE 0x1000 | |
330 | #define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */ | |
331 | #define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ | |
332 | ||
333 | #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ | |
334 | #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) | |
335 | #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET | |
336 | ||
337 | /*----------------------------------------------------------------------- | |
338 | * External Bus Controller (EBC) Setup | |
339 | */ | |
340 | ||
341 | /* Memory Bank 0 (Flash/SRAM) initialization */ | |
342 | #define CFG_EBC_PB0AP 0x04006000 | |
343 | #define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */ | |
344 | ||
345 | /* Memory Bank 1 (NVRAM/RTC) initialization */ | |
346 | #define CFG_EBC_PB1AP 0x04041000 | |
347 | #define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ | |
348 | ||
349 | /* Memory Bank 2 (not used) initialization */ | |
350 | #define CFG_EBC_PB2AP 0x00000000 | |
351 | #define CFG_EBC_PB2CR 0x00000000 | |
352 | ||
353 | /* Memory Bank 2 (not used) initialization */ | |
354 | #define CFG_EBC_PB3AP 0x00000000 | |
355 | #define CFG_EBC_PB3CR 0x00000000 | |
356 | ||
357 | /* Memory Bank 4 (FPGA regs) initialization */ | |
358 | #define CFG_EBC_PB4AP 0x01815000 | |
359 | #define CFG_EBC_PB4CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ | |
360 | ||
361 | /*----------------------------------------------------------------------- | |
362 | * Definitions for Serial Presence Detect EEPROM address | |
363 | * (to get SDRAM settings) | |
364 | */ | |
365 | #define SPD_EEPROM_ADDRESS 0x55 | |
366 | ||
367 | /*----------------------------------------------------------------------- | |
368 | * Definitions for GPIO setup (PPC405EP specific) | |
369 | * | |
370 | * GPIO0[0] - External Bus Controller BLAST output | |
371 | * GPIO0[1-9] - Instruction trace outputs | |
372 | * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs | |
373 | * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs | |
374 | * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs | |
375 | * GPIO0[24-27] - UART0 control signal inputs/outputs | |
376 | * GPIO0[28-29] - UART1 data signal input/output | |
377 | * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs | |
378 | */ | |
379 | #define CFG_GPIO0_OSRH 0x55555555 | |
380 | #define CFG_GPIO0_OSRL 0x40000110 | |
381 | #define CFG_GPIO0_ISR1H 0x00000000 | |
382 | #define CFG_GPIO0_ISR1L 0x15555445 | |
383 | #define CFG_GPIO0_TSRH 0x00000000 | |
384 | #define CFG_GPIO0_TSRL 0x00000000 | |
385 | #define CFG_GPIO0_TCR 0xFFFF8014 | |
386 | ||
387 | /*----------------------------------------------------------------------- | |
388 | * Some BUBINGA stuff... | |
389 | */ | |
390 | #define NVRAM_BASE 0xF0000000 | |
391 | #define FPGA_REG0 0xF0300000 /* FPGA Reg 0 */ | |
392 | #define FPGA_REG1 0xF0300001 /* FPGA Reg 1 */ | |
393 | #define NVRVFY1 0x4f532d4f /* used to determine if state data in */ | |
394 | #define NVRVFY2 0x50454e00 /* NVRAM initialized (ascii for OS-OPEN)*/ | |
395 | ||
396 | #define FPGA_REG0_F_RANGE 0x80 /* SDRAM PLL freq range */ | |
397 | #define FPGA_REG0_EXT_INT_DIS 0x20 /* External interface disable */ | |
398 | #define FPGA_REG0_LED_MASK 0x07 /* Board LEDs DS9, DS10, and DS11 */ | |
399 | #define FPGA_REG0_LED0 0x04 /* Turn on LED0 */ | |
400 | #define FPGA_REG0_LED1 0x02 /* Turn on LED1 */ | |
401 | #define FPGA_REG0_LED2 0x01 /* Turn on LED2 */ | |
402 | ||
403 | #define FPGA_REG1_SSPEC_DIS 0x80 /* C9531 Spread Spectrum disabled */ | |
404 | #define FPGA_REG1_OFFBD_PCICLK 0x40 /* Onboard PCI clock selected */ | |
405 | #define FPGA_REG1_CLOCK_MASK 0x30 /* Mask for C9531 output freq select */ | |
406 | #define FPGA_REG1_CLOCK_BIT_SHIFT 4 | |
407 | #define FPGA_REG1_PCI_INT_ARB 0x08 /* PCI Internal arbiter selected */ | |
408 | #define FPGA_REG1_PCI_FREQ 0x04 /* PCI Frequency select */ | |
409 | #define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */ | |
410 | #define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */ | |
411 | ||
412 | ||
413 | /* | |
414 | * Internal Definitions | |
415 | * | |
416 | * Boot Flags | |
417 | */ | |
418 | #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ | |
419 | #define BOOTFLAG_WARM 0x02 /* Software reboot */ | |
420 | ||
421 | #if (CONFIG_COMMANDS & CFG_CMD_KGDB) | |
422 | #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ | |
423 | #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ | |
424 | #endif | |
425 | ||
426 | #endif /* __CONFIG_H */ |