[people/ms/u-boot.git] / include / configs / M5253DEMO.h

/* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
 * Hayden Fraser (Hayden.Fraser@freescale.com)
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _M5253DEMO_H
#define _M5253DEMO_H

#define CONFIG_M5253DEMO	/* define board type */

#define CONFIG_MCFTMR

#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT		(0)
#define CONFIG_BAUDRATE		115200

#undef CONFIG_WATCHDOG		/* disable watchdog */


/* Configuration for environment
 * Environment is embedded in u-boot in the second sector of the flash
 */
#ifdef CONFIG_MONITOR_IS_IN_RAM
#	define CONFIG_ENV_OFFSET		0x4000
#	define CONFIG_ENV_SECT_SIZE	0x1000
#	define CONFIG_ENV_IS_IN_FLASH	1
#else
#	define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x4000)
#	define CONFIG_ENV_SECT_SIZE	0x1000
#	define CONFIG_ENV_IS_IN_FLASH	1
#endif

#define LDS_BOARD_TEXT \
        . = DEFINED(env_offset) ? env_offset : .; \
        common/env_embedded.o (.text*);

/*
 * Command line configuration.
 */
#define CONFIG_CMD_IDE

#ifdef CONFIG_CMD_IDE
/* ATA */
#	define CONFIG_DOS_PARTITION
#	define CONFIG_MAC_PARTITION
#	define CONFIG_IDE_RESET		1
#	define CONFIG_IDE_PREINIT	1
#	define CONFIG_ATAPI
#	undef CONFIG_LBA48

#	define CONFIG_SYS_IDE_MAXBUS		1
#	define CONFIG_SYS_IDE_MAXDEVICE	2

#	define CONFIG_SYS_ATA_BASE_ADDR	(CONFIG_SYS_MBAR2 + 0x800)
#	define CONFIG_SYS_ATA_IDE0_OFFSET	0

#	define CONFIG_SYS_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O */
#	define CONFIG_SYS_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
#	define CONFIG_SYS_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
#	define CONFIG_SYS_ATA_STRIDE		4	/* Interval between registers */
#endif

#define CONFIG_DRIVER_DM9000
#ifdef CONFIG_DRIVER_DM9000
#	define CONFIG_DM9000_BASE	(CONFIG_SYS_CS1_BASE | 0x300)
#	define DM9000_IO		CONFIG_DM9000_BASE
#	define DM9000_DATA		(CONFIG_DM9000_BASE + 4)
#	undef CONFIG_DM9000_DEBUG
#	define CONFIG_DM9000_BYTE_SWAPPED

#	define CONFIG_OVERWRITE_ETHADDR_ONCE

#	define CONFIG_EXTRA_ENV_SETTINGS		\
		"netdev=eth0\0"				\
		"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"	\
		"loadaddr=10000\0"			\
		"u-boot=u-boot.bin\0"			\
		"load=tftp ${loadaddr) ${u-boot}\0"	\
		"upd=run load; run prog\0"		\
		"prog=prot off 0xff800000 0xff82ffff;"	\
		"era 0xff800000 0xff82ffff;"		\
		"cp.b ${loadaddr} 0xff800000 ${filesize};"	\
		"save\0"				\
		""
#endif

#define CONFIG_HOSTNAME		M5253DEMO

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	80000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x00000280
#define CONFIG_SYS_IMMR		CONFIG_SYS_MBAR
#define CONFIG_SYS_I2C_PINMUX_REG	(*(u32 *) (CONFIG_SYS_MBAR+0x19C))
#define CONFIG_SYS_I2C_PINMUX_CLR	(0xFFFFE7FF)
#define CONFIG_SYS_I2C_PINMUX_SET	(0)

#define CONFIG_SYS_LONGHELP		/* undef to save memory */

#if defined(CONFIG_CMD_KGDB)
#	define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
#else
#	define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */

#define CONFIG_SYS_LOAD_ADDR		0x00100000

#define CONFIG_SYS_MEMTEST_START	0x400
#define CONFIG_SYS_MEMTEST_END		0x380000

#undef CONFIG_SYS_PLL_BYPASS		/* bypass PLL for test purpose */
#define CONFIG_SYS_FAST_CLK
#ifdef CONFIG_SYS_FAST_CLK
#	define CONFIG_SYS_PLLCR	0x1243E054
#	define CONFIG_SYS_CLK		140000000
#else
#	define CONFIG_SYS_PLLCR	0x135a4140
#	define CONFIG_SYS_CLK		70000000
#endif

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */

#define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */
#define CONFIG_SYS_MBAR2		0x80000000	/* Module Base Addrs 2 */

/*
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
#define CONFIG_SYS_INIT_RAM_SIZE	0x10000	/* Size of used area in internal SRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_SDRAM_SIZE		16	/* SDRAM size in MB */

#ifdef CONFIG_MONITOR_IS_IN_RAM
#	define CONFIG_SYS_MONITOR_BASE	0x20000
#else
#	define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
#endif

#define CONFIG_SYS_MONITOR_LEN		0x40000
#define CONFIG_SYS_MALLOC_LEN		(256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN	(64*1024)

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization ??
 */
#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
#define CONFIG_SYS_BOOTM_LEN		(CONFIG_SYS_SDRAM_SIZE << 20)

/* FLASH organization */
#define CONFIG_SYS_FLASH_BASE		(CONFIG_SYS_CS0_BASE)
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT	2048	/* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT	1000

#define FLASH_SST6401B		0x200
#define SST_ID_xF6401B		0x236D236D

#undef CONFIG_SYS_FLASH_CFI
#ifdef CONFIG_SYS_FLASH_CFI
/*
 * Unable to use CFI driver, due to incompatible sector erase command by SST.
 * Amd/Atmel use 0x30 for sector erase, SST use 0x50.
 * 0x30 is block erase in SST
 */
#	define CONFIG_FLASH_CFI_DRIVER	1
#	define CONFIG_SYS_FLASH_SIZE		0x800000
#	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
#	define CONFIG_FLASH_CFI_LEGACY
#else
#	define CONFIG_SYS_SST_SECT		2048
#	define CONFIG_SYS_SST_SECTSZ		0x1000
#	define CONFIG_SYS_FLASH_WRITE_TOUT	500
#endif

/* Cache Configuration */
#define CONFIG_SYS_CACHELINE_SIZE	16

#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV		(CF_CACR_DCM)
#define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_FLASH_BASE | \
					 CF_ADDRMASK(8) | \
					 CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ACR1		(CONFIG_SYS_SDRAM_BASE | \
					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
					 CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CEIB | \
					 CF_CACR_DBWE)

/* Port configuration */
#define CONFIG_SYS_FECI2C		0xF0

#define CONFIG_SYS_CS0_BASE		0xFF800000
#define CONFIG_SYS_CS0_MASK		0x007F0021
#define CONFIG_SYS_CS0_CTRL		0x00001D80

#define CONFIG_SYS_CS1_BASE		0xE0000000
#define CONFIG_SYS_CS1_MASK		0x00000001
#define CONFIG_SYS_CS1_CTRL		0x00003DD8

/*-----------------------------------------------------------------------
 * Port configuration
 */
#define CONFIG_SYS_GPIO_FUNC		0x00000008	/* Set gpio pins: none */
#define CONFIG_SYS_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54 */
#define CONFIG_SYS_GPIO_EN		0x00000008	/* Set gpio output enable */
#define CONFIG_SYS_GPIO1_EN		0x00c70000	/* Set gpio output enable */
#define CONFIG_SYS_GPIO_OUT		0x00000008	/* Set outputs to default state */
#define CONFIG_SYS_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
#define CONFIG_SYS_GPIO1_LED		0x00400000	/* user led */

#endif				/* _M5253DEMO_H */
Commit	Line	Data
6af3a0ea	1	/* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
6d33c6ac TL	2	* Hayden Fraser (Hayden.Fraser@freescale.com)
6d33c6ac TL	3	*
3765b3e7	4	* SPDX-License-Identifier: GPL-2.0+
6d33c6ac TL	5	*/
	6
	7	#ifndef _M5253DEMO_H
	8	#define _M5253DEMO_H
	9
6d33c6ac TL	10	#define CONFIG_M5253DEMO /* define board type */
	11
	12	#define CONFIG_MCFTMR
	13
	14	#define CONFIG_MCFUART
6d0f6bcf	15	#define CONFIG_SYS_UART_PORT (0)
6d33c6ac	16	#define CONFIG_BAUDRATE 115200
6d33c6ac TL	17
	18	#undef CONFIG_WATCHDOG /* disable watchdog */
	19
6d33c6ac TL	20
	21	/* Configuration for environment
	22	* Environment is embedded in u-boot in the second sector of the flash
	23	*/
	24	#ifdef CONFIG_MONITOR_IS_IN_RAM
0e8d1586 JCPV	25	# define CONFIG_ENV_OFFSET 0x4000
0e8d1586 JCPV	26	# define CONFIG_ENV_SECT_SIZE 0x1000
5a1aceb0	27	# define CONFIG_ENV_IS_IN_FLASH 1
6d33c6ac	28	#else
6d0f6bcf	29	# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000)
0e8d1586	30	# define CONFIG_ENV_SECT_SIZE 0x1000
5a1aceb0	31	# define CONFIG_ENV_IS_IN_FLASH 1
6d33c6ac TL	32	#endif
6d33c6ac TL	33
5296cb1d	34	#define LDS_BOARD_TEXT \
	35	. = DEFINED(env_offset) ? env_offset : .; \
	36	common/env_embedded.o (.text*);
	37
6d33c6ac TL	38	/*
	39	* Command line configuration.
	40	*/
6d33c6ac	41	#define CONFIG_CMD_IDE
6d33c6ac TL	42
	43	#ifdef CONFIG_CMD_IDE
	44	/* ATA */
	45	# define CONFIG_DOS_PARTITION
	46	# define CONFIG_MAC_PARTITION
	47	# define CONFIG_IDE_RESET 1
	48	# define CONFIG_IDE_PREINIT 1
	49	# define CONFIG_ATAPI
	50	# undef CONFIG_LBA48
	51
6d0f6bcf JCPV	52	# define CONFIG_SYS_IDE_MAXBUS 1
6d0f6bcf JCPV	53	# define CONFIG_SYS_IDE_MAXDEVICE 2
6d33c6ac	54
6d0f6bcf JCPV	55	# define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800)
6d0f6bcf JCPV	56	# define CONFIG_SYS_ATA_IDE0_OFFSET 0
6d33c6ac	57
6d0f6bcf JCPV	58	# define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */
	59	# define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */
	60	# define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */
	61	# define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */
6d33c6ac TL	62	#endif
	63
	64	#define CONFIG_DRIVER_DM9000
	65	#ifdef CONFIG_DRIVER_DM9000
012522fe	66	# define CONFIG_DM9000_BASE (CONFIG_SYS_CS1_BASE \| 0x300)
6d33c6ac TL	67	# define DM9000_IO CONFIG_DM9000_BASE
	68	# define DM9000_DATA (CONFIG_DM9000_BASE + 4)
	69	# undef CONFIG_DM9000_DEBUG
f73e7d67	70	# define CONFIG_DM9000_BYTE_SWAPPED
6d33c6ac	71
6d33c6ac TL	72	# define CONFIG_OVERWRITE_ETHADDR_ONCE
	73
	74	# define CONFIG_EXTRA_ENV_SETTINGS \
	75	"netdev=eth0\0" \
5368c55d	76	"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
6d33c6ac TL	77	"loadaddr=10000\0" \
	78	"u-boot=u-boot.bin\0" \
	79	"load=tftp ${loadaddr) ${u-boot}\0" \
	80	"upd=run load; run prog\0" \
ac265f7f TL	81	"prog=prot off 0xff800000 0xff82ffff;" \
ac265f7f TL	82	"era 0xff800000 0xff82ffff;" \
f26a2473	83	"cp.b ${loadaddr} 0xff800000 ${filesize};" \
6d33c6ac TL	84	"save\0" \
	85	""
	86	#endif
	87
	88	#define CONFIG_HOSTNAME M5253DEMO
	89
eec567a6	90	/* I2C */
00f792e0 HS	91	#define CONFIG_SYS_I2C
	92	#define CONFIG_SYS_I2C_FSL
	93	#define CONFIG_SYS_FSL_I2C_SPEED 80000
	94	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	95	#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280
6d0f6bcf JCPV	96	#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
	97	#define CONFIG_SYS_I2C_PINMUX_REG ((u32 ) (CONFIG_SYS_MBAR+0x19C))
	98	#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF)
	99	#define CONFIG_SYS_I2C_PINMUX_SET (0)
eec567a6	100
6d0f6bcf	101	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6d33c6ac TL	102
6d33c6ac TL	103	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	104	# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
6d33c6ac	105	#else
6d0f6bcf	106	# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
6d33c6ac	107	#endif
6d0f6bcf JCPV	108	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	109	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	110	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
6d33c6ac	111
6d0f6bcf	112	#define CONFIG_SYS_LOAD_ADDR 0x00100000
6d33c6ac	113
6d0f6bcf JCPV	114	#define CONFIG_SYS_MEMTEST_START 0x400
6d0f6bcf JCPV	115	#define CONFIG_SYS_MEMTEST_END 0x380000
6d33c6ac	116
6d0f6bcf JCPV	117	#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */
	118	#define CONFIG_SYS_FAST_CLK
	119	#ifdef CONFIG_SYS_FAST_CLK
	120	# define CONFIG_SYS_PLLCR 0x1243E054
	121	# define CONFIG_SYS_CLK 140000000
6d33c6ac	122	#else
6d0f6bcf JCPV	123	# define CONFIG_SYS_PLLCR 0x135a4140
6d0f6bcf JCPV	124	# define CONFIG_SYS_CLK 70000000
6d33c6ac TL	125	#endif
	126
	127	/*
	128	* Low Level Configuration Settings
	129	* (address mappings, register initial values, etc.)
	130	* You should know what you are doing if you make changes here.
	131	*/
	132
6d0f6bcf JCPV	133	#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
6d0f6bcf JCPV	134	#define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */
6d33c6ac TL	135
	136	/*
	137	* Definitions for initial stack pointer and data area (in DPRAM)
	138	*/
6d0f6bcf	139	#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
553f0982	140	#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
25ddd1fb	141	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	142	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
6d33c6ac TL	143
	144	/*
	145	* Start addresses for the final memory configuration
	146	* (Set up by the startup code)
6d0f6bcf	147	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
6d33c6ac	148	*/
6d0f6bcf JCPV	149	#define CONFIG_SYS_SDRAM_BASE 0x00000000
6d0f6bcf JCPV	150	#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
6d33c6ac TL	151
6d33c6ac TL	152	#ifdef CONFIG_MONITOR_IS_IN_RAM
6d0f6bcf	153	# define CONFIG_SYS_MONITOR_BASE 0x20000
6d33c6ac	154	#else
6d0f6bcf	155	# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
6d33c6ac TL	156	#endif
6d33c6ac TL	157
6d0f6bcf JCPV	158	#define CONFIG_SYS_MONITOR_LEN 0x40000
	159	#define CONFIG_SYS_MALLOC_LEN (256 << 10)
	160	#define CONFIG_SYS_BOOTPARAMS_LEN (64*1024)
6d33c6ac TL	161
	162	/*
	163	* For booting Linux, the board info and command line data
	164	* have to be in the first 8 MB of memory, since this is
	165	* the maximum mapped by the Linux kernel during initialization ??
	166	*/
6d0f6bcf	167	#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
d6e4baf4	168	#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
6d33c6ac TL	169
6d33c6ac TL	170	/* FLASH organization */
012522fe	171	#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
6d0f6bcf JCPV	172	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	173	#define CONFIG_SYS_MAX_FLASH_SECT 2048 /* max number of sectors on one chip */
	174	#define CONFIG_SYS_FLASH_ERASE_TOUT 1000
6d33c6ac TL	175
	176	#define FLASH_SST6401B 0x200
	177	#define SST_ID_xF6401B 0x236D236D
	178
6d0f6bcf JCPV	179	#undef CONFIG_SYS_FLASH_CFI
6d0f6bcf JCPV	180	#ifdef CONFIG_SYS_FLASH_CFI
6d33c6ac TL	181	/*
	182	* Unable to use CFI driver, due to incompatible sector erase command by SST.
	183	* Amd/Atmel use 0x30 for sector erase, SST use 0x50.
	184	* 0x30 is block erase in SST
	185	*/
0de0afbc	186	# define CONFIG_FLASH_CFI_DRIVER 1
6d0f6bcf JCPV	187	# define CONFIG_SYS_FLASH_SIZE 0x800000
6d0f6bcf JCPV	188	# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
6d33c6ac TL	189	# define CONFIG_FLASH_CFI_LEGACY
6d33c6ac TL	190	#else
6d0f6bcf JCPV	191	# define CONFIG_SYS_SST_SECT 2048
	192	# define CONFIG_SYS_SST_SECTSZ 0x1000
	193	# define CONFIG_SYS_FLASH_WRITE_TOUT 500
6d33c6ac TL	194	#endif
	195
	196	/* Cache Configuration */
6d0f6bcf	197	#define CONFIG_SYS_CACHELINE_SIZE 16
6d33c6ac	198
dd9f054e	199	#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	200	CONFIG_SYS_INIT_RAM_SIZE - 8)
dd9f054e	201	#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	202	CONFIG_SYS_INIT_RAM_SIZE - 4)
dd9f054e TL	203	#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM)
	204	#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE \| \
	205	CF_ADDRMASK(8) \| \
	206	CF_ACR_EN \| CF_ACR_SM_ALL)
	207	#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE \| \
	208	CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) \| \
	209	CF_ACR_EN \| CF_ACR_SM_ALL)
	210	#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB \| CF_CACR_CEIB \| \
	211	CF_CACR_DBWE)
	212
6d33c6ac	213	/* Port configuration */
6d0f6bcf	214	#define CONFIG_SYS_FECI2C 0xF0
6d33c6ac	215
012522fe TL	216	#define CONFIG_SYS_CS0_BASE 0xFF800000
	217	#define CONFIG_SYS_CS0_MASK 0x007F0021
	218	#define CONFIG_SYS_CS0_CTRL 0x00001D80
6d33c6ac	219
012522fe TL	220	#define CONFIG_SYS_CS1_BASE 0xE0000000
	221	#define CONFIG_SYS_CS1_MASK 0x00000001
	222	#define CONFIG_SYS_CS1_CTRL 0x00003DD8
6d33c6ac TL	223
	224	/*-----------------------------------------------------------------------
	225	* Port configuration
	226	*/
6d0f6bcf JCPV	227	#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
	228	#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */
	229	#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */
	230	#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */
	231	#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */
	232	#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
	233	#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */
6d33c6ac TL	234
6d33c6ac TL	235	#endif /* _M5253DEMO_H */