[people/ms/u-boot.git] / include / configs / M53017EVB.h

/*
 * Configuation settings for the Freescale MCF53017EVB.
 *
 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
 * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef _M53017EVB_H
#define _M53017EVB_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT		(0)
#define CONFIG_BAUDRATE			115200

#undef CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT		5000

/* Command line configuration */
#include <config_cmd_default.h>

#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FLASH
#undef CONFIG_CMD_I2C
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_MISC
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO

#define CONFIG_SYS_UNIFY_CACHE

#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
#	define CONFIG_MII		1
#	define CONFIG_MII_INIT		1
#	define CONFIG_SYS_DISCOVER_PHY
#	define CONFIG_SYS_RX_ETH_BUFFER	8
#	define CONFIG_SYS_TX_ETH_BUFFER	8
#	define CONFIG_SYS_FEC_BUF_USE_SRAM
#	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#	define CONFIG_HAS_ETH1

#	define CONFIG_SYS_FEC0_PINMUX	0
#	define CONFIG_SYS_FEC0_MIIBASE	CONFIG_SYS_FEC0_IOBASE
#	define CONFIG_SYS_FEC1_PINMUX	0
#	define CONFIG_SYS_FEC1_MIIBASE	CONFIG_SYS_FEC1_IOBASE
#	define MCFFEC_TOUT_LOOP		50000

#	define CONFIG_BOOTARGS		"root=/dev/mtdblock3 rw rootfstype=jffs2"

/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
#	ifndef CONFIG_SYS_DISCOVER_PHY
#		define FECDUPLEX	FULL
#		define FECSPEED		_100BASET
#	else
#		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#		endif
#	endif			/* CONFIG_SYS_DISCOVER_PHY */
#endif

#define CONFIG_MCFRTC
#undef RTC_DEBUG
#define CONFIG_SYS_RTC_CNT		(0x8000)
#define CONFIG_SYS_RTC_SETUP		(RTC_OCEN_OSCBYP | RTC_OCEN_CLKEN)

/* Timer */
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	80000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x58000
#define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR

#define CONFIG_BOOTDELAY		1	/* autoboot after 5 seconds */
#define CONFIG_UDP_CHECKSUM

#ifdef CONFIG_MCFFEC
#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
#	define CONFIG_ETH1ADDR	00:e0:0c:bc:e5:61
#	define CONFIG_IPADDR	192.162.1.2
#	define CONFIG_NETMASK	255.255.255.0
#	define CONFIG_SERVERIP	192.162.1.1
#	define CONFIG_GATEWAYIP	192.162.1.1
#	define CONFIG_OVERWRITE_ETHADDR_ONCE
#endif				/* FEC_ENET */

#define CONFIG_HOSTNAME		M53017
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"netdev=eth0\0"				\
	"loadaddr=40010000\0"			\
	"u-boot=u-boot.bin\0"			\
	"load=tftp ${loadaddr) ${u-boot}\0"	\
	"upd=run load; run prog\0"		\
	"prog=prot off 0 3ffff;"		\
	"era 0 3ffff;"				\
	"cp.b ${loadaddr} 0 ${filesize};"	\
	"save\0"				\
	""

#define CONFIG_PRAM		512	/* 512 KB */
#define CONFIG_SYS_PROMPT	"-> "
#define CONFIG_SYS_LONGHELP	/* undef to save memory */

#ifdef CONFIG_CMD_KGDB
#	define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
#else
#	define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
#endif

#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of cmd args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Arg Buf Sz */
#define CONFIG_SYS_LOAD_ADDR	0x40010000

#define CONFIG_SYS_CLK		80000000
#define CONFIG_SYS_CPU_CLK	CONFIG_SYS_CLK * 3

#define CONFIG_SYS_MBAR		0xFC000000

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */
/*
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR	0x80000000
#define CONFIG_SYS_INIT_RAM_SIZE		0x20000	/* Size of used area in internal SRAM */
#define CONFIG_SYS_INIT_RAM_CTRL	0x221
#define CONFIG_SYS_GBL_DATA_OFFSET	((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x40000000
#define CONFIG_SYS_SDRAM_SIZE		64	/* SDRAM size in MB */
#define CONFIG_SYS_SDRAM_CFG1		0x43711630
#define CONFIG_SYS_SDRAM_CFG2		0x56670000
#define CONFIG_SYS_SDRAM_CTRL		0xE1092000
#define CONFIG_SYS_SDRAM_EMOD		0x80010000
#define CONFIG_SYS_SDRAM_MODE		0x00CD0000

#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE + 0x400
#define CONFIG_SYS_MEMTEST_END		((CONFIG_SYS_SDRAM_SIZE - 3) << 20)

#define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_FLASH_BASE + 0x400)
#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */

#define CONFIG_SYS_BOOTPARAMS_LEN	64*1024
#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization ??
 */
#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
#define CONFIG_SYS_BOOTM_LEN		(CONFIG_SYS_SDRAM_SIZE << 20)

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CONFIG_SYS_FLASH_CFI
#ifdef CONFIG_SYS_FLASH_CFI
#	define CONFIG_FLASH_CFI_DRIVER		1
#	define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
#	define CONFIG_FLASH_SPANSION_S29WS_N	1
#	define CONFIG_SYS_FLASH_SIZE		0x1000000	/* Max size that the board might have */
#	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
#	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
#	define CONFIG_SYS_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
#	define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
#endif

#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_CS0_BASE

/* Configuration for environment
 * Environment is embedded in u-boot in the second sector of the flash
 */
#define CONFIG_ENV_OFFSET		0x8000
#define CONFIG_ENV_SIZE			0x1000
#define CONFIG_ENV_SECT_SIZE		0x8000
#define CONFIG_ENV_IS_IN_FLASH		1

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CONFIG_SYS_CACHELINE_SIZE	16

#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINVA)
#define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_SDRAM_BASE | \
					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
					 CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_EC | CF_CACR_CINVA | \
					 CF_CACR_DCM_P)

/*-----------------------------------------------------------------------
 * Chipselect bank definitions
 */
/*
 * CS0 - NOR Flash
 * CS1 - Ext SRAM
 * CS2 - Available
 * CS3 - Available
 * CS4 - Available
 * CS5 - Available
 */
#define CONFIG_SYS_CS0_BASE		0
#define CONFIG_SYS_CS0_MASK		0x00FF0001
#define CONFIG_SYS_CS0_CTRL		0x00001FA0

#define CONFIG_SYS_CS1_BASE		0xC0000000
#define CONFIG_SYS_CS1_MASK		0x00070001
#define CONFIG_SYS_CS1_CTRL		0x00001FA0

#endif				/* _M53017EVB_H */
Commit	Line	Data
536e7dac TL	1	/*
	2	* Configuation settings for the Freescale MCF53017EVB.
	3	*
	4	* Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
	5	* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
	6	*
3765b3e7	7	* SPDX-License-Identifier: GPL-2.0+
536e7dac TL	8	*/
	9
	10	/*
	11	* board/config.h - configuration options, board specific
	12	*/
	13
	14	#ifndef _M53017EVB_H
	15	#define _M53017EVB_H
	16
	17	/*
	18	* High Level Configuration Options
	19	* (easy to change)
	20	*/
536e7dac TL	21
	22	#define CONFIG_MCFUART
	23	#define CONFIG_SYS_UART_PORT (0)
	24	#define CONFIG_BAUDRATE 115200
536e7dac TL	25
	26	#undef CONFIG_WATCHDOG
	27	#define CONFIG_WATCHDOG_TIMEOUT 5000
	28
	29	/* Command line configuration */
	30	#include <config_cmd_default.h>
	31
	32	#define CONFIG_CMD_CACHE
	33	#define CONFIG_CMD_DATE
	34	#define CONFIG_CMD_ELF
	35	#define CONFIG_CMD_FLASH
	36	#undef CONFIG_CMD_I2C
	37	#define CONFIG_CMD_MEMORY
	38	#define CONFIG_CMD_MISC
	39	#define CONFIG_CMD_MII
	40	#define CONFIG_CMD_NET
	41	#define CONFIG_CMD_PING
	42	#define CONFIG_CMD_REGINFO
	43
	44	#define CONFIG_SYS_UNIFY_CACHE
	45
	46	#define CONFIG_MCFFEC
	47	#ifdef CONFIG_MCFFEC
536e7dac TL	48	# define CONFIG_MII 1
	49	# define CONFIG_MII_INIT 1
	50	# define CONFIG_SYS_DISCOVER_PHY
	51	# define CONFIG_SYS_RX_ETH_BUFFER 8
9e8e9270 TL	52	# define CONFIG_SYS_TX_ETH_BUFFER 8
9e8e9270 TL	53	# define CONFIG_SYS_FEC_BUF_USE_SRAM
536e7dac TL	54	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	55	# define CONFIG_HAS_ETH1
	56
	57	# define CONFIG_SYS_FEC0_PINMUX 0
	58	# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
	59	# define CONFIG_SYS_FEC1_PINMUX 0
	60	# define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC1_IOBASE
	61	# define MCFFEC_TOUT_LOOP 50000
052c0891 TL	62
	63	# define CONFIG_BOOTARGS "root=/dev/mtdblock3 rw rootfstype=jffs2"
	64
536e7dac TL	65	/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
	66	# ifndef CONFIG_SYS_DISCOVER_PHY
	67	# define FECDUPLEX FULL
	68	# define FECSPEED _100BASET
	69	# else
	70	# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	71	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	72	# endif
	73	# endif /* CONFIG_SYS_DISCOVER_PHY */
	74	#endif
	75
	76	#define CONFIG_MCFRTC
	77	#undef RTC_DEBUG
	78	#define CONFIG_SYS_RTC_CNT (0x8000)
	79	#define CONFIG_SYS_RTC_SETUP (RTC_OCEN_OSCBYP \| RTC_OCEN_CLKEN)
	80
	81	/* Timer */
	82	#define CONFIG_MCFTMR
	83	#undef CONFIG_MCFPIT
	84
	85	/* I2C */
00f792e0 HS	86	#define CONFIG_SYS_I2C
	87	#define CONFIG_SYS_I2C_FSL
	88	#define CONFIG_SYS_FSL_I2C_SPEED 80000
	89	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	90	#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
536e7dac TL	91	#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
	92
	93	#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
	94	#define CONFIG_UDP_CHECKSUM
	95
	96	#ifdef CONFIG_MCFFEC
	97	# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
	98	# define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61
	99	# define CONFIG_IPADDR 192.162.1.2
	100	# define CONFIG_NETMASK 255.255.255.0
	101	# define CONFIG_SERVERIP 192.162.1.1
	102	# define CONFIG_GATEWAYIP 192.162.1.1
	103	# define CONFIG_OVERWRITE_ETHADDR_ONCE
	104	#endif /* FEC_ENET */
	105
	106	#define CONFIG_HOSTNAME M53017
	107	#define CONFIG_EXTRA_ENV_SETTINGS \
	108	"netdev=eth0\0" \
	109	"loadaddr=40010000\0" \
	110	"u-boot=u-boot.bin\0" \
	111	"load=tftp ${loadaddr) ${u-boot}\0" \
	112	"upd=run load; run prog\0" \
	113	"prog=prot off 0 3ffff;" \
	114	"era 0 3ffff;" \
	115	"cp.b ${loadaddr} 0 ${filesize};" \
	116	"save\0" \
	117	""
	118
	119	#define CONFIG_PRAM 512 /* 512 KB */
	120	#define CONFIG_SYS_PROMPT "-> "
	121	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	122
	123	#ifdef CONFIG_CMD_KGDB
	124	# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	125	#else
	126	# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	127	#endif
	128
	129	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	130	#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */
	131	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buf Sz */
	132	#define CONFIG_SYS_LOAD_ADDR 0x40010000
	133
536e7dac TL	134	#define CONFIG_SYS_CLK 80000000
	135	#define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 3
	136
	137	#define CONFIG_SYS_MBAR 0xFC000000
	138
	139	/*
	140	* Low Level Configuration Settings
	141	* (address mappings, register initial values, etc.)
	142	* You should know what you are doing if you make changes here.
	143	*/
	144	/*
	145	* Definitions for initial stack pointer and data area (in DPRAM)
	146	*/
	147	#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
553f0982	148	#define CONFIG_SYS_INIT_RAM_SIZE 0x20000 /* Size of used area in internal SRAM */
9e8e9270	149	#define CONFIG_SYS_INIT_RAM_CTRL 0x221
25ddd1fb	150	#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
536e7dac TL	151	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	152
	153	/*
	154	* Start addresses for the final memory configuration
	155	* (Set up by the startup code)
	156	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	157	*/
	158	#define CONFIG_SYS_SDRAM_BASE 0x40000000
	159	#define CONFIG_SYS_SDRAM_SIZE 64 /* SDRAM size in MB */
	160	#define CONFIG_SYS_SDRAM_CFG1 0x43711630
	161	#define CONFIG_SYS_SDRAM_CFG2 0x56670000
9e8e9270	162	#define CONFIG_SYS_SDRAM_CTRL 0xE1092000
536e7dac TL	163	#define CONFIG_SYS_SDRAM_EMOD 0x80010000
	164	#define CONFIG_SYS_SDRAM_MODE 0x00CD0000
	165
	166	#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400
	167	#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
	168
	169	#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
	170	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	171
	172	#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
	173	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	174
	175	/*
	176	* For booting Linux, the board info and command line data
	177	* have to be in the first 8 MB of memory, since this is
	178	* the maximum mapped by the Linux kernel during initialization ??
	179	*/
	180	#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
d6e4baf4	181	#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
536e7dac TL	182
	183	/*-----------------------------------------------------------------------
	184	* FLASH organization
	185	*/
	186	#define CONFIG_SYS_FLASH_CFI
	187	#ifdef CONFIG_SYS_FLASH_CFI
	188	# define CONFIG_FLASH_CFI_DRIVER 1
bbf6bbff TL	189	# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
bbf6bbff TL	190	# define CONFIG_FLASH_SPANSION_S29WS_N 1
4567c7bf	191	# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
536e7dac TL	192	# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	193	# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	194	# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
	195	# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
	196	#endif
	197
	198	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
	199
	200	/* Configuration for environment
	201	* Environment is embedded in u-boot in the second sector of the flash
	202	*/
	203	#define CONFIG_ENV_OFFSET 0x8000
	204	#define CONFIG_ENV_SIZE 0x1000
	205	#define CONFIG_ENV_SECT_SIZE 0x8000
	206	#define CONFIG_ENV_IS_IN_FLASH 1
	207
	208	/*-----------------------------------------------------------------------
	209	* Cache Configuration
	210	*/
	211	#define CONFIG_SYS_CACHELINE_SIZE 16
	212
dd9f054e	213	#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	214	CONFIG_SYS_INIT_RAM_SIZE - 8)
dd9f054e	215	#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	216	CONFIG_SYS_INIT_RAM_SIZE - 4)
dd9f054e TL	217	#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA)
	218	#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE \| \
	219	CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) \| \
	220	CF_ACR_EN \| CF_ACR_SM_ALL)
	221	#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC \| CF_CACR_CINVA \| \
	222	CF_CACR_DCM_P)
	223
536e7dac TL	224	/*-----------------------------------------------------------------------
	225	* Chipselect bank definitions
	226	*/
	227	/*
	228	* CS0 - NOR Flash
	229	* CS1 - Ext SRAM
	230	* CS2 - Available
	231	* CS3 - Available
	232	* CS4 - Available
	233	* CS5 - Available
	234	*/
	235	#define CONFIG_SYS_CS0_BASE 0
	236	#define CONFIG_SYS_CS0_MASK 0x00FF0001
	237	#define CONFIG_SYS_CS0_CTRL 0x00001FA0
	238
	239	#define CONFIG_SYS_CS1_BASE 0xC0000000
	240	#define CONFIG_SYS_CS1_MASK 0x00070001
	241	#define CONFIG_SYS_CS1_CTRL 0x00001FA0
	242
	243	#endif /* _M53017EVB_H */