[people/ms/u-boot.git] / include / configs / ML2.h

/*
 * ML2.h: ML2 specific config options
 *
 * Copyright 2002 Mind NV
 *
 * http://www.mind.be/
 *
 * Author : Peter De Schrijver (p2@mind.be)
 *
 * Derived from : other configuration header files in this tree
 *
 * This software may be used and distributed according to the terms of
 * the GNU General Public License (GPL) version 2, incorporated herein by
 * reference. Drivers based on or derived from this code fall under the GPL
 * and must retain the authorship, copyright and this license notice. This
 * file is not a complete program and may only be used when the entire
 * program is licensed under the GPL.
 *
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405		1	/* This is a PPC405 CPU		*/
#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
#define CONFIG_ML2	1	/* ...on a ML2 board	*/

#define	CONFIG_SYS_TEXT_BASE	0x18000000

#define CONFIG_ENV_IS_IN_FLASH     1

#ifdef CONFIG_ENV_IS_IN_NVRAM
#undef CONFIG_ENV_IS_IN_FLASH
#else
#ifdef CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_ENV_IS_IN_NVRAM
#endif
#endif

#define CONFIG_BAUDRATE		9600
#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

#if 1
#define CONFIG_BOOTCOMMAND	"bootm" /* autoboot command	*/
#else
#define CONFIG_BOOTCOMMAND	"bootp" /* autoboot command		*/
#endif

#define CONFIG_PREBOOT		"fsload 0x00100000 /boot/image"

#if 0
#define CONFIG_BOOTARGS		"root=/dev/nfs "                        \
    "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "        \
    "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
#else
#define CONFIG_BOOTARGS		"root=/dev/mtdblock2 "			\
   "console=ttyS0 console=tty"

#endif

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_IRQ
#define CONFIG_CMD_KGDB
#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_ELF
#define CONFIG_CMD_JFFS2

#undef CONFIG_CMD_NET
#undef CONFIG_CMD_NFS
#undef CONFIG_CMD_RTC
#undef CONFIG_CMD_PCI
#undef CONFIG_CMD_I2C


#undef CONFIG_WATCHDOG			/* watchdog disabled		*/

#define CONFIG_SYS_CLK_FREQ 50000000

#define CONFIG_SPD_EEPROM      1       /* use SPD EEPROM for setup    */

/*
 * I2C
 */
#define CONFIG_HARD_I2C			/* I2C with hardware support	*/
#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
#define CONFIG_SYS_I2C_SLAVE	0x7F
#define CONFIG_SYS_I2C_SPEED	400000

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
#if defined(CONFIG_CMD_KGDB)
#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

/*
 * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
 * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
 * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
 * The Linux BASE_BAUD define should match this configuration.
 *    baseBaud = cpuClock/(uartDivisor*16)
 * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
 * set Linux BASE_BAUD to 403200.
 */
#undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* external serial clock */
#undef  CONFIG_SYS_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */

#define CONFIG_SYS_BASE_BAUD       (3125000*16)
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD
#define CONFIG_SYS_DUART_CHAN		0
#define CONFIG_SYS_NS16550_COM1	0xa0001003
#define CONFIG_SYS_NS16550_COM2	0xa0011003
#define CONFIG_SYS_NS16550_REG_SIZE -4
#define CONFIG_SYS_NS16550 1
#define CONFIG_SYS_INIT_CHAN1	 1
#define CONFIG_SYS_INIT_CHAN2	 1

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE  \
    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}

#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */

#define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/


/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE		0x18000000
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 196 kB for Monitor	*/
#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

/* BEG ENVIRONNEMENT FLASH */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OFFSET		0x00050000 /* Offset of Environment Sector  */
#define	CONFIG_ENV_SIZE		0x10000	/* Total Size of Environment Sector	*/
#define CONFIG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
#endif
/* END ENVIRONNEMENT FLASH */
/*-----------------------------------------------------------------------
 * NVRAM organization
 */
#define CONFIG_SYS_NVRAM_BASE_ADDR	0xf0000000	/* NVRAM base address	*/
#define CONFIG_SYS_NVRAM_SIZE		0x1ff8		/* NVRAM size	*/

#ifdef CONFIG_ENV_IS_IN_NVRAM
#define CONFIG_ENV_SIZE		0x1000		/* Size of Environment vars	*/
#define CONFIG_ENV_ADDR		\
	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)	/* Env	*/
#endif

/*
 * Init Memory Controller:
 *
 * BR0/1 and OR0/1 (FLASH)
 */

#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
#define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/


/* Configuration Port location */
#define CONFIG_PORT_ADDR	0xF0000500

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */

#define CONFIG_SYS_INIT_RAM_ADDR       0x800000  /* inside of SDRAM                     */
#define CONFIG_SYS_INIT_RAM_SIZE        0x2000  /* Size of used area in RAM             */
#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Definitions for Serial Presence Detect EEPROM address
 * (to get SDRAM settings)
 */
#define SPD_EEPROM_ADDRESS      0x50

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif

/*
 * JFFS2 partitions
 *
 */
/* No command line, one static partition, whole device */
#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV		"nor0"
#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET	0x00080000

/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT		"nor0=ml2-0"
#define MTDPARTS_DEFAULT	"mtdparts=ml2-0:-@512k(jffs2)"
*/

#endif	/* __CONFIG_H */
Commit	Line	Data
fe8c2806 WD	1	/*
	2	* ML2.h: ML2 specific config options
	3	*
	4	* Copyright 2002 Mind NV
	5	*
	6	* http://www.mind.be/
	7	*
	8	* Author : Peter De Schrijver (p2@mind.be)
	9	*
	10	* Derived from : other configuration header files in this tree
	11	*
	12	* This software may be used and distributed according to the terms of
	13	* the GNU General Public License (GPL) version 2, incorporated herein by
	14	* reference. Drivers based on or derived from this code fall under the GPL
	15	* and must retain the authorship, copyright and this license notice. This
	16	* file is not a complete program and may only be used when the entire
	17	* program is licensed under the GPL.
	18	*
	19	*/
	20
	21	#ifndef __CONFIG_H
	22	#define __CONFIG_H
	23
	24	/*
	25	* High Level Configuration Options
	26	* (easy to change)
	27	*/
	28
	29	#define CONFIG_405 1 /* This is a PPC405 CPU */
	30	#define CONFIG_4xx 1 /* ...member of PPC4xx family */
	31	#define CONFIG_ML2 1 /* ...on a ML2 board */
	32
2ae18241	33	#define CONFIG_SYS_TEXT_BASE 0x18000000
fe8c2806	34
5a1aceb0	35	#define CONFIG_ENV_IS_IN_FLASH 1
fe8c2806	36
9314cee6	37	#ifdef CONFIG_ENV_IS_IN_NVRAM
5a1aceb0	38	#undef CONFIG_ENV_IS_IN_FLASH
fe8c2806	39	#else
5a1aceb0	40	#ifdef CONFIG_ENV_IS_IN_FLASH
9314cee6	41	#undef CONFIG_ENV_IS_IN_NVRAM
fe8c2806 WD	42	#endif
	43	#endif
	44
	45	#define CONFIG_BAUDRATE 9600
	46	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
	47
	48	#if 1
	49	#define CONFIG_BOOTCOMMAND "bootm" /* autoboot command */
	50	#else
	51	#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
	52	#endif
	53
	54	#define CONFIG_PREBOOT "fsload 0x00100000 /boot/image"
	55
fe8c2806 WD	56	#if 0
	57	#define CONFIG_BOOTARGS "root=/dev/nfs " \
	58	"ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
	59	"nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
	60	#else
	61	#define CONFIG_BOOTARGS "root=/dev/mtdblock2 " \
	62	"console=ttyS0 console=tty"
	63
	64	#endif
	65
	66	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
6d0f6bcf	67	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
fe8c2806 WD	68
fe8c2806 WD	69
659e2f67 JL	70	/*
	71	* BOOTP options
	72	*/
	73	#define CONFIG_BOOTP_BOOTFILESIZE
	74	#define CONFIG_BOOTP_BOOTPATH
	75	#define CONFIG_BOOTP_GATEWAY
	76	#define CONFIG_BOOTP_HOSTNAME
	77
	78
8353e139 JL	79	/*
	80	* Command line configuration.
	81	*/
	82	#include <config_cmd_default.h>
	83
	84	#define CONFIG_CMD_IRQ
	85	#define CONFIG_CMD_KGDB
	86	#define CONFIG_CMD_BEDBUG
	87	#define CONFIG_CMD_ELF
	88	#define CONFIG_CMD_JFFS2
	89
	90	#undef CONFIG_CMD_NET
ee8028b7	91	#undef CONFIG_CMD_NFS
8353e139 JL	92	#undef CONFIG_CMD_RTC
	93	#undef CONFIG_CMD_PCI
	94	#undef CONFIG_CMD_I2C
	95
fe8c2806 WD	96
	97	#undef CONFIG_WATCHDOG /* watchdog disabled */
	98
	99	#define CONFIG_SYS_CLK_FREQ 50000000
	100
	101	#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
	102
ee8028b7 WD	103	/*
	104	* I2C
	105	*/
	106	#define CONFIG_HARD_I2C /* I2C with hardware support */
	107	#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
	108	#define CONFIG_SYS_I2C_SLAVE 0x7F
	109	#define CONFIG_SYS_I2C_SPEED 400000
	110
fe8c2806 WD	111	/*
	112	* Miscellaneous configurable options
	113	*/
6d0f6bcf JCPV	114	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6d0f6bcf JCPV	115	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
8353e139	116	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	117	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
fe8c2806	118	#else
6d0f6bcf	119	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
fe8c2806	120	#endif
6d0f6bcf JCPV	121	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	122	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	123	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
fe8c2806	124
6d0f6bcf JCPV	125	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
6d0f6bcf JCPV	126	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
fe8c2806 WD	127
fe8c2806 WD	128	/*
6d0f6bcf JCPV	129	* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
	130	* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
	131	* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
fe8c2806 WD	132	* The Linux BASE_BAUD define should match this configuration.
fe8c2806 WD	133	* baseBaud = cpuClock/(uartDivisor*16)
6d0f6bcf	134	* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
fe8c2806 WD	135	* set Linux BASE_BAUD to 403200.
fe8c2806 WD	136	*/
6d0f6bcf JCPV	137	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
	138	#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
	139
	140	#define CONFIG_SYS_BASE_BAUD (3125000*16)
	141	#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD
	142	#define CONFIG_SYS_DUART_CHAN 0
	143	#define CONFIG_SYS_NS16550_COM1 0xa0001003
	144	#define CONFIG_SYS_NS16550_COM2 0xa0011003
	145	#define CONFIG_SYS_NS16550_REG_SIZE -4
	146	#define CONFIG_SYS_NS16550 1
	147	#define CONFIG_SYS_INIT_CHAN1 1
	148	#define CONFIG_SYS_INIT_CHAN2 1
fe8c2806 WD	149
fe8c2806 WD	150	/* The following table includes the supported baudrates */
6d0f6bcf	151	#define CONFIG_SYS_BAUDRATE_TABLE \
fe8c2806 WD	152	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
fe8c2806 WD	153
6d0f6bcf JCPV	154	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6d0f6bcf JCPV	155	#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
fe8c2806	156
6d0f6bcf	157	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
fe8c2806 WD	158
fe8c2806 WD	159
fe8c2806 WD	160	/*-----------------------------------------------------------------------
	161	* Start addresses for the final memory configuration
	162	* (Set up by the startup code)
6d0f6bcf	163	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
fe8c2806	164	*/
6d0f6bcf JCPV	165	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	166	#define CONFIG_SYS_FLASH_BASE 0x18000000
	167	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	168	#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
	169	#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
fe8c2806 WD	170
	171	/*
	172	* For booting Linux, the board info and command line data
	173	* have to be in the first 8 MB of memory, since this is
	174	* the maximum mapped by the Linux kernel during initialization.
	175	*/
6d0f6bcf	176	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
fe8c2806 WD	177	/*-----------------------------------------------------------------------
	178	* FLASH organization
	179	*/
6d0f6bcf JCPV	180	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
6d0f6bcf JCPV	181	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
fe8c2806	182
6d0f6bcf JCPV	183	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	184	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
fe8c2806 WD	185
fe8c2806 WD	186	/* BEG ENVIRONNEMENT FLASH */
5a1aceb0	187	#ifdef CONFIG_ENV_IS_IN_FLASH
0e8d1586 JCPV	188	#define CONFIG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */
	189	#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
	190	#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
fe8c2806 WD	191	#endif
	192	/* END ENVIRONNEMENT FLASH */
	193	/*-----------------------------------------------------------------------
	194	* NVRAM organization
	195	*/
6d0f6bcf JCPV	196	#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
6d0f6bcf JCPV	197	#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */
fe8c2806	198
9314cee6	199	#ifdef CONFIG_ENV_IS_IN_NVRAM
0e8d1586 JCPV	200	#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
0e8d1586 JCPV	201	#define CONFIG_ENV_ADDR \
6d0f6bcf	202	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
fe8c2806	203	#endif
fe8c2806 WD	204
	205	/*
	206	* Init Memory Controller:
	207	*
	208	* BR0/1 and OR0/1 (FLASH)
	209	*/
	210
6d0f6bcf	211	#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
fe8c2806 WD	212	#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
	213
	214
	215	/* Configuration Port location */
	216	#define CONFIG_PORT_ADDR 0xF0000500
	217
	218	/*-----------------------------------------------------------------------
	219	* Definitions for initial stack pointer and data area (in DPRAM)
	220	*/
	221
6d0f6bcf	222	#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */
553f0982	223	#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
25ddd1fb	224	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	225	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
fe8c2806 WD	226
	227	/*-----------------------------------------------------------------------
	228	* Definitions for Serial Presence Detect EEPROM address
	229	* (to get SDRAM settings)
	230	*/
	231	#define SPD_EEPROM_ADDRESS 0x50
	232
8353e139	233	#if defined(CONFIG_CMD_KGDB)
fe8c2806 WD	234	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	235	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	236	#endif
	237
700a0c64 WD	238	/*
	239	* JFFS2 partitions
	240	*
	241	*/
	242	/* No command line, one static partition, whole device */
68d7d651	243	#undef CONFIG_CMD_MTDPARTS
700a0c64 WD	244	#define CONFIG_JFFS2_DEV "nor0"
	245	#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
	246	#define CONFIG_JFFS2_PART_OFFSET 0x00080000
	247
	248	/* mtdparts command line support */
	249	/* Note: fake mtd_id used, no linux mtd map file */
	250	/*
68d7d651	251	#define CONFIG_CMD_MTDPARTS
700a0c64 WD	252	#define MTDIDS_DEFAULT "nor0=ml2-0"
	253	#define MTDPARTS_DEFAULT "mtdparts=ml2-0:-@512k(jffs2)"
	254	*/
fe8c2806	255
fe8c2806	256	#endif /* __CONFIG_H */