[people/ms/u-boot.git] / include / configs / MPC832XEMDS.h

/*
 * Copyright (C) 2006 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300		1	/* E300 family */
#define CONFIG_QE		1	/* Has QE */
#define CONFIG_MPC832x		1	/* MPC832x CPU specific */
#define CONFIG_MPC832XEMDS	1	/* MPC832XEMDS board specific */

#define	CONFIG_SYS_TEXT_BASE	0xFE000000

/*
 * System Clock Setup
 */
#ifdef CONFIG_PCISLAVE
#define CONFIG_83XX_PCICLK	66000000	/* in HZ */
#else
#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
#endif

#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ	66000000
#endif

/*
 * Hardware Reset Configuration Word
 */
#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
	HRCWL_DDR_TO_SCB_CLK_2X1 |\
	HRCWL_VCO_1X2 |\
	HRCWL_CSB_TO_CLKIN_2X1 |\
	HRCWL_CORE_TO_CSB_2X1 |\
	HRCWL_CE_PLL_VCO_DIV_2 |\
	HRCWL_CE_PLL_DIV_1X1 |\
	HRCWL_CE_TO_PLL_1X3)

#ifdef CONFIG_PCISLAVE
#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_AGENT |\
	HRCWH_PCI1_ARBITER_DISABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0XFFF00100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_BIG_ENDIAN |\
	HRCWH_LALE_NORMAL)
#else
#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST |\
	HRCWH_PCI1_ARBITER_ENABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0X00000100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_BIG_ENDIAN |\
	HRCWH_LALE_NORMAL)
#endif

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRL		0x00000000

#define CONFIG_BOARD_EARLY_INIT_R

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR		0xE0000000

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE	0x00000000	/* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE	CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDRCDR	0x73000002	/* DDR II voltage is 1.8V */

#undef CONFIG_SPD_EEPROM
#if defined(CONFIG_SPD_EEPROM)
/* Determine DDR configuration from I2C interface
 */
#define SPD_EEPROM_ADDRESS	0x51	/* DDR SODIMM */
#else
/* Manually set up DDR parameters
 */
#define CONFIG_SYS_DDR_SIZE		128	/* MB */
#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
					| CSCONFIG_AP \
					| CSCONFIG_ODT_WR_CFG \
					| CSCONFIG_ROW_BIT_13 \
					| CSCONFIG_COL_BIT_10)
					/* 0x80840102 */
#define CONFIG_SYS_DDR_TIMING_0		((0 << TIMING_CFG0_RWT_SHIFT) \
					| (0 << TIMING_CFG0_WRT_SHIFT) \
					| (0 << TIMING_CFG0_RRT_SHIFT) \
					| (0 << TIMING_CFG0_WWT_SHIFT) \
					| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
					| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
					| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
					| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
					/* 0x00220802 */
#define CONFIG_SYS_DDR_TIMING_1		((3 << TIMING_CFG1_PRETOACT_SHIFT) \
					| (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
					| (3 << TIMING_CFG1_ACTTORW_SHIFT) \
					| (5 << TIMING_CFG1_CASLAT_SHIFT) \
					| (13 << TIMING_CFG1_REFREC_SHIFT) \
					| (3 << TIMING_CFG1_WRREC_SHIFT) \
					| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
					| (2 << TIMING_CFG1_WRTORD_SHIFT))
					/* 0x3935D322 */
#define CONFIG_SYS_DDR_TIMING_2		((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
				| (31 << TIMING_CFG2_CPO_SHIFT) \
				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
				| (10 << TIMING_CFG2_FOUR_ACT_SHIFT))
				/* 0x0F9048CA */
#define CONFIG_SYS_DDR_TIMING_3		0x00000000
#define CONFIG_SYS_DDR_CLK_CNTL		DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
					/* 0x02000000 */
#define CONFIG_SYS_DDR_MODE		((0x4440 << SDRAM_MODE_ESD_SHIFT) \
					| (0x0232 << SDRAM_MODE_SD_SHIFT))
					/* 0x44400232 */
#define CONFIG_SYS_DDR_MODE2		0x8000c000
#define CONFIG_SYS_DDR_INTERVAL		((800 << SDRAM_INTERVAL_REFINT_SHIFT) \
					| (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
					/* 0x03200064 */
#define CONFIG_SYS_DDR_CS0_BNDS		0x00000007
#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
					| SDRAM_CFG_SDRAM_TYPE_DDR2 \
					| SDRAM_CFG_32_BE)
					/* 0x43080000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
#endif

/*
 * Memory test
 */
#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
#define CONFIG_SYS_MEMTEST_END		0x00100000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef  CONFIG_SYS_RAMBOOT
#endif

/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	/* Reserve 512 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN	(256 * 1024)	/* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000	/* Initial RAM addr */
#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET	\
			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR		0x00000000

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE	0xFE000000	/* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE	16	/* FLASH size is 16M */
#define CONFIG_SYS_FLASH_PROTECTION	1	/* Use h/w Flash protection. */

					/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_32MB)

#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
				| BR_PS_16	/* 16 bit port */ \
				| BR_MS_GPCM	/* MSEL = GPCM */ \
				| BR_V)		/* valid */
#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
				| OR_GPCM_XAM \
				| OR_GPCM_CSNT \
				| OR_GPCM_ACS_DIV2 \
				| OR_GPCM_XACS \
				| OR_GPCM_SCY_15 \
				| OR_GPCM_TRLX_SET \
				| OR_GPCM_EHTR_SET \
				| OR_GPCM_EAD)
				/* 0xfe006ff7 */

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	128	/* sectors per device */

#undef CONFIG_SYS_FLASH_CHECKSUM

/*
 * BCSR on the Local Bus
 */
#define CONFIG_SYS_BCSR			0xF8000000
					/* Access window base at BCSR base */
#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_BCSR
#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)

#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_BCSR \
					| BR_PS_8 \
					| BR_MS_GPCM \
					| BR_V)
#define CONFIG_SYS_OR1_PRELIM		(OR_AM_32KB \
					| OR_GPCM_XAM \
					| OR_GPCM_CSNT \
					| OR_GPCM_XACS \
					| OR_GPCM_SCY_15 \
					| OR_GPCM_TRLX_SET \
					| OR_GPCM_EHTR_SET \
					| OR_GPCM_EAD)
					/* 0xFFFFE9F7 */

/*
 * Windows to access PIB via local bus
 */
					/* PIB window base 0xF8008000 */
#define CONFIG_SYS_PIB_BASE		0xF8008000
#define CONFIG_SYS_PIB_WINDOW_SIZE	(32 * 1024)
#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_PIB_BASE
#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_64KB)

/*
 * CS2 on Local Bus, to PIB
 */
#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_PIB_BASE \
				| BR_PS_8 \
				| BR_MS_GPCM \
				| BR_V)
				/* 0xF8008801 */
#define CONFIG_SYS_OR2_PRELIM	(P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
				| OR_GPCM_XAM \
				| OR_GPCM_CSNT \
				| OR_GPCM_XACS \
				| OR_GPCM_SCY_15 \
				| OR_GPCM_TRLX_SET \
				| OR_GPCM_EHTR_SET \
				| OR_GPCM_EAD)
				/* 0xffffe9f7 */

/*
 * CS3 on Local Bus, to PIB
 */
#define CONFIG_SYS_BR3_PRELIM	((CONFIG_SYS_PIB_BASE + \
					CONFIG_SYS_PIB_WINDOW_SIZE) \
				| BR_PS_8 \
				| BR_MS_GPCM \
				| BR_V)
				/* 0xF8010801 */
#define CONFIG_SYS_OR3_PRELIM	(P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
				| OR_GPCM_XAM \
				| OR_GPCM_CSNT \
				| OR_GPCM_XACS \
				| OR_GPCM_SCY_15 \
				| OR_GPCM_TRLX_SET \
				| OR_GPCM_EHTR_SET \
				| OR_GPCM_EAD)
				/* 0xffffe9f7 */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX	1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)

#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
#define CONFIG_AUTO_COMPLETE		/* add autocompletion support   */

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x51} }

/*
 * Config on-board RTC
 */
#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR	0x68	/* at address 0x68 */

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS		0xE0300000
#define CONFIG_SYS_PCI1_IO_SIZE		0x100000	/* 1M */

#define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
#define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000

#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE

#define CONFIG_83XX_PCI_STREAMING

#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */

#endif	/* CONFIG_PCI */

/*
 * QE UEC ethernet configuration
 */
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME		"UEC0"

#define CONFIG_UEC_ETH1		/* ETH3 */

#ifdef CONFIG_UEC_ETH1
#define CONFIG_SYS_UEC1_UCC_NUM	2	/* UCC3 */
#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK9
#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK10
#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR	3
#define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_MII
#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
#endif

#define CONFIG_UEC_ETH2		/* ETH4 */

#ifdef CONFIG_UEC_ETH2
#define CONFIG_SYS_UEC2_UCC_NUM	3	/* UCC4 */
#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK7
#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK8
#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR	4
#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_MII
#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
#endif

/*
 * Environment
 */
#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_IS_IN_FLASH	1
	#define CONFIG_ENV_ADDR		\
			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_ENV_SECT_SIZE	0x20000
	#define CONFIG_ENV_SIZE		0x2000
#else
	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */

#if defined(CONFIG_PCI)
    #define CONFIG_CMD_PCI
#endif

#undef CONFIG_WATCHDOG		/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP	/* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
#else
	#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
#endif

				/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
				/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
					/* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT	0x000000000
#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
				 HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2		HID2_HBE

/*
 * MMU Setup
 */

#define CONFIG_HIGH_BATS	1	/* High BATs supported */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
				| BATL_PP_RW \
				| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
				| BATU_BL_256M \
				| BATU_VS \
				| BATU_VP)
#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U

/* IMMRBAR & PCI IO: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR \
				| BATL_PP_RW \
				| BATL_CACHEINHIBIT \
				| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR \
				| BATU_BL_4M \
				| BATU_VS \
				| BATU_VP)
#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U

/* BCSR: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_BCSR \
				| BATL_PP_RW \
				| BATL_CACHEINHIBIT \
				| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_BCSR \
				| BATU_BL_128K \
				| BATU_VS \
				| BATU_VP)
#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_FLASH_BASE \
				| BATL_PP_RW \
				| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_FLASH_BASE \
				| BATU_BL_32M \
				| BATU_VS \
				| BATU_VP)
#define CONFIG_SYS_DBAT3L	(CONFIG_SYS_FLASH_BASE \
				| BATL_PP_RW \
				| BATL_CACHEINHIBIT \
				| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

#define CONFIG_SYS_IBAT4L	(0)
#define CONFIG_SYS_IBAT4U	(0)
#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_INIT_RAM_ADDR \
				| BATU_BL_128K \
				| BATU_VS \
				| BATU_VP)
#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U

#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI1_MEM_PHYS \
				| BATL_PP_RW \
				| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI1_MEM_PHYS \
				| BATU_BL_256M \
				| BATU_VS \
				| BATU_VP)
#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT7L	(CONFIG_SYS_PCI1_MMIO_PHYS \
				| BATL_PP_RW \
				| BATL_CACHEINHIBIT \
				| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT7U	(CONFIG_SYS_PCI1_MMIO_PHYS \
				| BATU_BL_256M \
				| BATU_VS \
				| BATU_VP)
#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
#else
#define CONFIG_SYS_IBAT6L	(0)
#define CONFIG_SYS_IBAT6U	(0)
#define CONFIG_SYS_IBAT7L	(0)
#define CONFIG_SYS_IBAT7U	(0)
#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
#endif

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
#endif

/*
 * Environment Configuration
 */ #define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif

#define CONFIG_BAUDRATE	115200

#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */

#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */

#define CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"consoledev=ttyS0\0"						\
	"ramdiskaddr=1000000\0"						\
	"ramdiskfile=ramfs.83xx\0"					\
	"fdtaddr=780000\0"						\
	"fdtfile=mpc832x_mds.dtb\0"					\
	""

#define CONFIG_NFSBOOTCOMMAND						\
	"setenv bootargs root=/dev/nfs rw "				\
		"nfsroot=$serverip:$rootpath "				\
		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
							"$netdev:off "	\
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND						\
	"setenv bootargs root=/dev/ram rw "				\
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $ramdiskaddr $ramdiskfile;"				\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND

#endif	/* __CONFIG_H */
Commit	Line	Data
24c3aca3 DL	1	/*
	2	* Copyright (C) 2006 Freescale Semiconductor, Inc.
	3	*
1a459660	4	* SPDX-License-Identifier: GPL-2.0+
24c3aca3 DL	5	*/
	6
	7	#ifndef __CONFIG_H
	8	#define __CONFIG_H
	9
24c3aca3 DL	10	/*
	11	* High Level Configuration Options
	12	*/
	13	#define CONFIG_E300 1 /* E300 family */
	14	#define CONFIG_QE 1 /* Has QE */
2c7920af	15	#define CONFIG_MPC832x 1 /* MPC832x CPU specific */
24c3aca3	16	#define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */
2ae18241 WD	17
2ae18241 WD	18	#define CONFIG_SYS_TEXT_BASE 0xFE000000
24c3aca3 DL	19
	20	/*
	21	* System Clock Setup
	22	*/
	23	#ifdef CONFIG_PCISLAVE
	24	#define CONFIG_83XX_PCICLK 66000000 /* in HZ */
	25	#else
	26	#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
	27	#endif
	28
	29	#ifndef CONFIG_SYS_CLK_FREQ
	30	#define CONFIG_SYS_CLK_FREQ 66000000
	31	#endif
	32
	33	/*
	34	* Hardware Reset Configuration Word
	35	*/
6d0f6bcf	36	#define CONFIG_SYS_HRCW_LOW (\
24c3aca3 DL	37	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	38	HRCWL_DDR_TO_SCB_CLK_2X1 \|\
	39	HRCWL_VCO_1X2 \|\
	40	HRCWL_CSB_TO_CLKIN_2X1 \|\
	41	HRCWL_CORE_TO_CSB_2X1 \|\
	42	HRCWL_CE_PLL_VCO_DIV_2 \|\
	43	HRCWL_CE_PLL_DIV_1X1 \|\
	44	HRCWL_CE_TO_PLL_1X3)
	45
	46	#ifdef CONFIG_PCISLAVE
6d0f6bcf	47	#define CONFIG_SYS_HRCW_HIGH (\
24c3aca3 DL	48	HRCWH_PCI_AGENT \|\
	49	HRCWH_PCI1_ARBITER_DISABLE \|\
	50	HRCWH_CORE_ENABLE \|\
	51	HRCWH_FROM_0XFFF00100 \|\
	52	HRCWH_BOOTSEQ_DISABLE \|\
	53	HRCWH_SW_WATCHDOG_DISABLE \|\
	54	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	55	HRCWH_BIG_ENDIAN \|\
	56	HRCWH_LALE_NORMAL)
	57	#else
6d0f6bcf	58	#define CONFIG_SYS_HRCW_HIGH (\
24c3aca3 DL	59	HRCWH_PCI_HOST \|\
	60	HRCWH_PCI1_ARBITER_ENABLE \|\
	61	HRCWH_CORE_ENABLE \|\
	62	HRCWH_FROM_0X00000100 \|\
	63	HRCWH_BOOTSEQ_DISABLE \|\
	64	HRCWH_SW_WATCHDOG_DISABLE \|\
	65	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	66	HRCWH_BIG_ENDIAN \|\
	67	HRCWH_LALE_NORMAL)
	68	#endif
	69
	70	/*
	71	* System IO Config
	72	*/
6d0f6bcf	73	#define CONFIG_SYS_SICRL 0x00000000
24c3aca3	74
14778585	75	#define CONFIG_BOARD_EARLY_INIT_R
24c3aca3 DL	76
	77	/*
	78	* IMMR new address
	79	*/
6d0f6bcf	80	#define CONFIG_SYS_IMMR 0xE0000000
24c3aca3 DL	81
	82	/*
	83	* DDR Setup
	84	*/
989091ac JH	85	#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
989091ac JH	86	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
6d0f6bcf	87	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
989091ac	88	#define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */
24c3aca3 DL	89
	90	#undef CONFIG_SPD_EEPROM
	91	#if defined(CONFIG_SPD_EEPROM)
	92	/* Determine DDR configuration from I2C interface
	93	*/
	94	#define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */
	95	#else
	96	/* Manually set up DDR parameters
	97	*/
6d0f6bcf	98	#define CONFIG_SYS_DDR_SIZE 128 /* MB */
2fef4020 JH	99	#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
	100	\| CSCONFIG_AP \
	101	\| CSCONFIG_ODT_WR_CFG \
	102	\| CSCONFIG_ROW_BIT_13 \
	103	\| CSCONFIG_COL_BIT_10)
	104	/* 0x80840102 */
	105	#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
	106	\| (0 << TIMING_CFG0_WRT_SHIFT) \
	107	\| (0 << TIMING_CFG0_RRT_SHIFT) \
	108	\| (0 << TIMING_CFG0_WWT_SHIFT) \
	109	\| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
	110	\| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
	111	\| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
	112	\| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
	113	/* 0x00220802 */
	114	#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
	115	\| (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
	116	\| (3 << TIMING_CFG1_ACTTORW_SHIFT) \
	117	\| (5 << TIMING_CFG1_CASLAT_SHIFT) \
	118	\| (13 << TIMING_CFG1_REFREC_SHIFT) \
	119	\| (3 << TIMING_CFG1_WRREC_SHIFT) \
	120	\| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
	121	\| (2 << TIMING_CFG1_WRTORD_SHIFT))
	122	/* 0x3935D322 */
	123	#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
	124	\| (31 << TIMING_CFG2_CPO_SHIFT) \
	125	\| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
	126	\| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
	127	\| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
	128	\| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
	129	\| (10 << TIMING_CFG2_FOUR_ACT_SHIFT))
	130	/* 0x0F9048CA */
989091ac	131	#define CONFIG_SYS_DDR_TIMING_3 0x00000000
2fef4020 JH	132	#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
	133	/* 0x02000000 */
	134	#define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \
	135	\| (0x0232 << SDRAM_MODE_SD_SHIFT))
	136	/* 0x44400232 */
6d0f6bcf	137	#define CONFIG_SYS_DDR_MODE2 0x8000c000
2fef4020 JH	138	#define CONFIG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \
	139	\| (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
	140	/* 0x03200064 */
989091ac	141	#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
2fef4020 JH	142	#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
	143	\| SDRAM_CFG_SDRAM_TYPE_DDR2 \
	144	\| SDRAM_CFG_32_BE)
	145	/* 0x43080000 */
6d0f6bcf	146	#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
24c3aca3 DL	147	#endif
	148
	149	/*
	150	* Memory test
	151	*/
6d0f6bcf JCPV	152	#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
	153	#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
	154	#define CONFIG_SYS_MEMTEST_END 0x00100000
24c3aca3 DL	155
	156	/*
	157	* The reserved memory
	158	*/
14d0a02a	159	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
24c3aca3	160
6d0f6bcf JCPV	161	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
6d0f6bcf JCPV	162	#define CONFIG_SYS_RAMBOOT
24c3aca3	163	#else
6d0f6bcf	164	#undef CONFIG_SYS_RAMBOOT
24c3aca3 DL	165	#endif
24c3aca3 DL	166
6d0f6bcf	167	/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
16c8c170	168	#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
3b6b256c	169	#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
24c3aca3 DL	170
	171	/*
	172	* Initial RAM Base Address Setup
	173	*/
6d0f6bcf	174	#define CONFIG_SYS_INIT_RAM_LOCK 1
989091ac JH	175	#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM addr */
	176	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
	177	#define CONFIG_SYS_GBL_DATA_OFFSET \
	178	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
24c3aca3 DL	179
	180	/*
	181	* Local Bus Configuration & Clock Setup
	182	*/
c7190f02 KP	183	#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
c7190f02 KP	184	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
6d0f6bcf	185	#define CONFIG_SYS_LBC_LBCR 0x00000000
24c3aca3 DL	186
	187	/*
	188	* FLASH on the Local Bus
	189	*/
6d0f6bcf	190	#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
989091ac JH	191	#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
	192	#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
	193	#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */
	194	#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
24c3aca3	195
989091ac JH	196	/* Window base at flash base */
989091ac JH	197	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
7d6a0982	198	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_32MB)
24c3aca3	199
989091ac	200	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
7d6a0982 JH	201	\| BR_PS_16 /* 16 bit port */ \
	202	\| BR_MS_GPCM /* MSEL = GPCM */ \
	203	\| BR_V) /* valid */
	204	#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
	205	\| OR_GPCM_XAM \
	206	\| OR_GPCM_CSNT \
	207	\| OR_GPCM_ACS_DIV2 \
	208	\| OR_GPCM_XACS \
	209	\| OR_GPCM_SCY_15 \
	210	\| OR_GPCM_TRLX_SET \
	211	\| OR_GPCM_EHTR_SET \
	212	\| OR_GPCM_EAD)
	213	/* 0xfe006ff7 */
24c3aca3	214
989091ac JH	215	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
989091ac JH	216	#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
24c3aca3	217
6d0f6bcf	218	#undef CONFIG_SYS_FLASH_CHECKSUM
24c3aca3 DL	219
	220	/*
	221	* BCSR on the Local Bus
	222	*/
989091ac JH	223	#define CONFIG_SYS_BCSR 0xF8000000
	224	/* Access window base at BCSR base */
	225	#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR
7d6a0982 JH	226	#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN \| LBLAWAR_32KB)
	227
	228	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \
	229	\| BR_PS_8 \
	230	\| BR_MS_GPCM \
	231	\| BR_V)
	232	#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \
	233	\| OR_GPCM_XAM \
	234	\| OR_GPCM_CSNT \
	235	\| OR_GPCM_XACS \
	236	\| OR_GPCM_SCY_15 \
	237	\| OR_GPCM_TRLX_SET \
	238	\| OR_GPCM_EHTR_SET \
	239	\| OR_GPCM_EAD)
	240	/* 0xFFFFE9F7 */
24c3aca3 DL	241
	242	/*
	243	* Windows to access PIB via local bus
	244	*/
7d6a0982 JH	245	/* PIB window base 0xF8008000 */
	246	#define CONFIG_SYS_PIB_BASE 0xF8008000
	247	#define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024)
	248	#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PIB_BASE
	249	#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN \| LBLAWAR_64KB)
24c3aca3 DL	250
	251	/*
	252	* CS2 on Local Bus, to PIB
	253	*/
7d6a0982 JH	254	#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_PIB_BASE \
	255	\| BR_PS_8 \
	256	\| BR_MS_GPCM \
	257	\| BR_V)
	258	/* 0xF8008801 */
	259	#define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
	260	\| OR_GPCM_XAM \
	261	\| OR_GPCM_CSNT \
	262	\| OR_GPCM_XACS \
	263	\| OR_GPCM_SCY_15 \
	264	\| OR_GPCM_TRLX_SET \
	265	\| OR_GPCM_EHTR_SET \
	266	\| OR_GPCM_EAD)
	267	/* 0xffffe9f7 */
24c3aca3 DL	268
	269	/*
	270	* CS3 on Local Bus, to PIB
	271	*/
7d6a0982 JH	272	#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIB_BASE + \
	273	CONFIG_SYS_PIB_WINDOW_SIZE) \
	274	\| BR_PS_8 \
	275	\| BR_MS_GPCM \
	276	\| BR_V)
	277	/* 0xF8010801 */
	278	#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
	279	\| OR_GPCM_XAM \
	280	\| OR_GPCM_CSNT \
	281	\| OR_GPCM_XACS \
	282	\| OR_GPCM_SCY_15 \
	283	\| OR_GPCM_TRLX_SET \
	284	\| OR_GPCM_EHTR_SET \
	285	\| OR_GPCM_EAD)
	286	/* 0xffffe9f7 */
24c3aca3 DL	287
	288	/*
	289	* Serial Port
	290	*/
	291	#define CONFIG_CONS_INDEX 1
6d0f6bcf JCPV	292	#define CONFIG_SYS_NS16550_SERIAL
	293	#define CONFIG_SYS_NS16550_REG_SIZE 1
	294	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
24c3aca3	295
6d0f6bcf	296	#define CONFIG_SYS_BAUDRATE_TABLE \
989091ac	297	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
24c3aca3	298
6d0f6bcf JCPV	299	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
6d0f6bcf JCPV	300	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
24c3aca3	301
22d71a71	302	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
a059e90e	303	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
24c3aca3	304
24c3aca3	305	/* I2C */
00f792e0 HS	306	#define CONFIG_SYS_I2C
	307	#define CONFIG_SYS_I2C_FSL
	308	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	309	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	310	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	311	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
24c3aca3 DL	312
	313	/*
	314	* Config on-board RTC
	315	*/
	316	#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
6d0f6bcf	317	#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
24c3aca3 DL	318
	319	/*
	320	* General PCI
	321	* Addresses are mapped 1-1.
	322	*/
9993e196 KP	323	#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
	324	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
	325	#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
	326	#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
	327	#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
	328	#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	329	#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
	330	#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000
	331	#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
24c3aca3	332
6d0f6bcf JCPV	333	#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
	334	#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
	335	#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
24c3aca3	336
24c3aca3	337	#ifdef CONFIG_PCI
842033e6	338	#define CONFIG_PCI_INDIRECT_BRIDGE
24c3aca3	339
9993e196	340	#define CONFIG_83XX_PCI_STREAMING
24c3aca3 DL	341
	342	#undef CONFIG_EEPRO100
	343	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
6d0f6bcf	344	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
24c3aca3 DL	345
	346	#endif /* CONFIG_PCI */
	347
24c3aca3 DL	348	/*
	349	* QE UEC ethernet configuration
	350	*/
	351	#define CONFIG_UEC_ETH
78b7a8ef	352	#define CONFIG_ETHPRIME "UEC0"
24c3aca3 DL	353
	354	#define CONFIG_UEC_ETH1 /* ETH3 */
	355
	356	#ifdef CONFIG_UEC_ETH1
6d0f6bcf JCPV	357	#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */
	358	#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
	359	#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
	360	#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
	361	#define CONFIG_SYS_UEC1_PHY_ADDR 3
865ff856	362	#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
582c55a0	363	#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
24c3aca3 DL	364	#endif
	365
	366	#define CONFIG_UEC_ETH2 /* ETH4 */
	367
	368	#ifdef CONFIG_UEC_ETH2
6d0f6bcf JCPV	369	#define CONFIG_SYS_UEC2_UCC_NUM 3 /* UCC4 */
	370	#define CONFIG_SYS_UEC2_RX_CLK QE_CLK7
	371	#define CONFIG_SYS_UEC2_TX_CLK QE_CLK8
	372	#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
	373	#define CONFIG_SYS_UEC2_PHY_ADDR 4
865ff856	374	#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
582c55a0	375	#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
24c3aca3 DL	376	#endif
	377
	378	/*
	379	* Environment
	380	*/
6d0f6bcf	381	#ifndef CONFIG_SYS_RAMBOOT
5a1aceb0	382	#define CONFIG_ENV_IS_IN_FLASH 1
989091ac JH	383	#define CONFIG_ENV_ADDR \
989091ac JH	384	(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
0e8d1586 JCPV	385	#define CONFIG_ENV_SECT_SIZE 0x20000
0e8d1586 JCPV	386	#define CONFIG_ENV_SIZE 0x2000
24c3aca3	387	#else
93f6d725	388	#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
6d0f6bcf	389	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
0e8d1586	390	#define CONFIG_ENV_SIZE 0x2000
24c3aca3 DL	391	#endif
	392
	393	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
6d0f6bcf	394	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
24c3aca3	395
079a136c JL	396	/*
	397	* BOOTP options
	398	*/
	399	#define CONFIG_BOOTP_BOOTFILESIZE
	400	#define CONFIG_BOOTP_BOOTPATH
	401	#define CONFIG_BOOTP_GATEWAY
	402	#define CONFIG_BOOTP_HOSTNAME
	403
8ea5499a JL	404	/*
	405	* Command line configuration.
	406	*/
8ea5499a	407
24c3aca3	408	#if defined(CONFIG_PCI)
8ea5499a	409	#define CONFIG_CMD_PCI
24c3aca3	410	#endif
8ea5499a	411
24c3aca3 DL	412	#undef CONFIG_WATCHDOG /* watchdog disabled */
	413
	414	/*
	415	* Miscellaneous configurable options
	416	*/
989091ac JH	417	#define CONFIG_SYS_LONGHELP /* undef to save memory */
989091ac JH	418	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
24c3aca3	419
8ea5499a	420	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	421	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
24c3aca3	422	#else
6d0f6bcf	423	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
24c3aca3 DL	424	#endif
24c3aca3 DL	425
989091ac JH	426	/* Print Buffer Size */
	427	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
	428	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	429	/* Boot Argument Buffer Size */
	430	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
24c3aca3 DL	431
	432	/*
	433	* For booting Linux, the board info and command line data
9f530d59	434	* have to be in the first 256 MB of memory, since this is
24c3aca3 DL	435	* the maximum mapped by the Linux kernel during initialization.
24c3aca3 DL	436	*/
989091ac JH	437	/* Initial Memory map for Linux */
989091ac JH	438	#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
63865278	439	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
24c3aca3 DL	440
	441	/*
	442	* Core HID Setup
	443	*/
1a2e203b KP	444	#define CONFIG_SYS_HID0_INIT 0x000000000
	445	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \| \
	446	HID0_ENABLE_INSTRUCTION_CACHE)
6d0f6bcf	447	#define CONFIG_SYS_HID2 HID2_HBE
24c3aca3	448
24c3aca3 DL	449	/*
	450	* MMU Setup
	451	*/
	452
31d82672 BB	453	#define CONFIG_HIGH_BATS 1 /* High BATs supported */
31d82672 BB	454
24c3aca3	455	/* DDR: cache cacheable */
989091ac	456	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
72cd4087	457	\| BATL_PP_RW \
989091ac JH	458	\| BATL_MEMCOHERENCE)
	459	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
	460	\| BATU_BL_256M \
	461	\| BATU_VS \
	462	\| BATU_VP)
6d0f6bcf JCPV	463	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
6d0f6bcf JCPV	464	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
24c3aca3 DL	465
24c3aca3 DL	466	/* IMMRBAR & PCI IO: cache-inhibit and guarded */
989091ac	467	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
72cd4087	468	\| BATL_PP_RW \
989091ac JH	469	\| BATL_CACHEINHIBIT \
	470	\| BATL_GUARDEDSTORAGE)
	471	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
	472	\| BATU_BL_4M \
	473	\| BATU_VS \
	474	\| BATU_VP)
6d0f6bcf JCPV	475	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
6d0f6bcf JCPV	476	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
24c3aca3 DL	477
24c3aca3 DL	478	/* BCSR: cache-inhibit and guarded */
989091ac	479	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \
72cd4087	480	\| BATL_PP_RW \
989091ac JH	481	\| BATL_CACHEINHIBIT \
	482	\| BATL_GUARDEDSTORAGE)
	483	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \
	484	\| BATU_BL_128K \
	485	\| BATU_VS \
	486	\| BATU_VP)
6d0f6bcf JCPV	487	#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
6d0f6bcf JCPV	488	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
24c3aca3 DL	489
24c3aca3 DL	490	/* FLASH: icache cacheable, but dcache-inhibit and guarded */
989091ac	491	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \
72cd4087	492	\| BATL_PP_RW \
989091ac JH	493	\| BATL_MEMCOHERENCE)
	494	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \
	495	\| BATU_BL_32M \
	496	\| BATU_VS \
	497	\| BATU_VP)
	498	#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \
72cd4087	499	\| BATL_PP_RW \
989091ac JH	500	\| BATL_CACHEINHIBIT \
989091ac JH	501	\| BATL_GUARDEDSTORAGE)
6d0f6bcf	502	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
24c3aca3	503
6d0f6bcf JCPV	504	#define CONFIG_SYS_IBAT4L (0)
	505	#define CONFIG_SYS_IBAT4U (0)
	506	#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
	507	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
24c3aca3 DL	508
24c3aca3 DL	509	/* Stack in dcache: cacheable, no memory coherence */
72cd4087	510	#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_RW)
989091ac JH	511	#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \
	512	\| BATU_BL_128K \
	513	\| BATU_VS \
	514	\| BATU_VP)
6d0f6bcf JCPV	515	#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
6d0f6bcf JCPV	516	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
24c3aca3 DL	517
	518	#ifdef CONFIG_PCI
	519	/* PCI MEM space: cacheable */
989091ac	520	#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \
72cd4087	521	\| BATL_PP_RW \
989091ac JH	522	\| BATL_MEMCOHERENCE)
	523	#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \
	524	\| BATU_BL_256M \
	525	\| BATU_VS \
	526	\| BATU_VP)
6d0f6bcf JCPV	527	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
6d0f6bcf JCPV	528	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
24c3aca3	529	/* PCI MMIO space: cache-inhibit and guarded */
989091ac	530	#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \
72cd4087	531	\| BATL_PP_RW \
989091ac JH	532	\| BATL_CACHEINHIBIT \
	533	\| BATL_GUARDEDSTORAGE)
	534	#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \
	535	\| BATU_BL_256M \
	536	\| BATU_VS \
	537	\| BATU_VP)
6d0f6bcf JCPV	538	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
6d0f6bcf JCPV	539	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
24c3aca3	540	#else
6d0f6bcf JCPV	541	#define CONFIG_SYS_IBAT6L (0)
	542	#define CONFIG_SYS_IBAT6U (0)
	543	#define CONFIG_SYS_IBAT7L (0)
	544	#define CONFIG_SYS_IBAT7U (0)
	545	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
	546	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
	547	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
	548	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
24c3aca3 DL	549	#endif
24c3aca3 DL	550
8ea5499a	551	#if defined(CONFIG_CMD_KGDB)
24c3aca3	552	#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
24c3aca3 DL	553	#endif
	554
	555	/*
	556	* Environment Configuration
9993e196	557	*/ #define CONFIG_ENV_OVERWRITE
24c3aca3 DL	558
24c3aca3 DL	559	#if defined(CONFIG_UEC_ETH)
977b5758	560	#define CONFIG_HAS_ETH0
24c3aca3	561	#define CONFIG_HAS_ETH1
24c3aca3 DL	562	#endif
	563
	564	#define CONFIG_BAUDRATE 115200
	565
79f516bc	566	#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
24c3aca3	567
24c3aca3 DL	568	#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
	569
	570	#define CONFIG_EXTRA_ENV_SETTINGS \
989091ac JH	571	"netdev=eth0\0" \
	572	"consoledev=ttyS0\0" \
	573	"ramdiskaddr=1000000\0" \
	574	"ramdiskfile=ramfs.83xx\0" \
	575	"fdtaddr=780000\0" \
	576	"fdtfile=mpc832x_mds.dtb\0" \
	577	""
24c3aca3 DL	578
24c3aca3 DL	579	#define CONFIG_NFSBOOTCOMMAND \
989091ac JH	580	"setenv bootargs root=/dev/nfs rw " \
	581	"nfsroot=$serverip:$rootpath " \
	582	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
	583	"$netdev:off " \
	584	"console=$consoledev,$baudrate $othbootargs;" \
	585	"tftp $loadaddr $bootfile;" \
	586	"tftp $fdtaddr $fdtfile;" \
	587	"bootm $loadaddr - $fdtaddr"
24c3aca3 DL	588
24c3aca3 DL	589	#define CONFIG_RAMBOOTCOMMAND \
989091ac JH	590	"setenv bootargs root=/dev/ram rw " \
	591	"console=$consoledev,$baudrate $othbootargs;" \
	592	"tftp $ramdiskaddr $ramdiskfile;" \
	593	"tftp $loadaddr $bootfile;" \
	594	"tftp $fdtaddr $fdtfile;" \
	595	"bootm $loadaddr $ramdiskaddr $fdtaddr"
24c3aca3	596
24c3aca3 DL	597	#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
	598
	599	#endif /* __CONFIG_H */