[people/ms/u-boot.git] / include / configs / MPC8560ADS.h

/*
 * Copyright 2004, 2011 Freescale Semiconductor.
 * (C) Copyright 2002,2003 Motorola,Inc.
 * Xianghua Xiao <X.Xiao@motorola.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * mpc8560ads board configuration file
 *
 * Please refer to doc/README.mpc85xx for more info.
 *
 * Make sure you change the MAC address and other network params first,
 * search for CONFIG_SERVERIP, etc. in this file.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* High Level Configuration Options */
#define CONFIG_BOOKE		1	/* BOOKE */
#define CONFIG_E500		1	/* BOOKE e500 family */
#define CONFIG_CPM2		1	/* has CPM2 */
#define CONFIG_MPC8560ADS	1	/* MPC8560ADS board specific */
#define CONFIG_MPC8560		1

/*
 * default CCARBAR is at 0xff700000
 * assume U-Boot is less than 0.5MB
 */
#define	CONFIG_SYS_TEXT_BASE	0xfff80000

#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
#define CONFIG_TSEC_ENET		/* tsec ethernet support */
#undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
#define CONFIG_RESET_PHY_R	1	/* Call reset_phy() */

/*
 * sysclk for MPC85xx
 *
 * Two valid values are:
 *    33000000
 *    66000000
 *
 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
 * is likely the desired value here, so that is now the default.
 * The board, however, can run at 66MHz.  In any event, this value
 * must match the settings of some switches.  Details can be found
 * in the README.mpc85xxads.
 */

#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ	33000000
#endif

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE			/* toggle L2 cache */
#define CONFIG_BTB			/* toggle branch predition */

#define CONFIG_SYS_INIT_DBCR DBCR_IDM		/* Enable Debug Exceptions */

#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
#define CONFIG_SYS_MEMTEST_END		0x00400000

#define CONFIG_SYS_CCSRBAR		0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR

/* DDR Setup */
#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE

#define CONFIG_MEM_INIT_VALUE		0xDeadBeef

#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_NUM_DDR_CONTROLLERS	1
#define CONFIG_DIMM_SLOTS_PER_CTLR	1
#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)

/* I2C addresses of SPD EEPROMs */
#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */

/* These are used when DDR doesn't use SPD.  */
#define CONFIG_SYS_SDRAM_SIZE	128		/* DDR is 128MB */
#define CONFIG_SYS_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
#define CONFIG_SYS_DDR_CS0_CONFIG	0x80000002
#define CONFIG_SYS_DDR_TIMING_1	0x37344321
#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
#define CONFIG_SYS_DDR_CONTROL		0xc2000000	/* unbuffered,no DYN_PWR */
#define CONFIG_SYS_DDR_MODE		0x00000062	/* DLL,normal,seq,4/2.5 */
#define CONFIG_SYS_DDR_INTERVAL	0x05200100	/* autocharge,no open page */

/*
 * SDRAM on the Local Bus
 */
#define CONFIG_SYS_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */

#define CONFIG_SYS_FLASH_BASE		0xff000000	/* start of FLASH 16M */
#define CONFIG_SYS_BR0_PRELIM		0xff001801	/* port size 32bit */

#define CONFIG_SYS_OR0_PRELIM		0xff006ff7	/* 16MB Flash */
#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	64		/* sectors per device */
#undef	CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef  CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO

#undef CONFIG_CLOCKS_IN_MHZ

/*
 * Local Bus Definitions
 */

/*
 * Base Register 2 and Option Register 2 configure SDRAM.
 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
 *
 * For BR2, need:
 *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
 *    port-size = 32-bits = BR2[19:20] = 11
 *    no parity checking = BR2[21:22] = 00
 *    SDRAM for MSEL = BR2[24:26] = 011
 *    Valid = BR[31] = 1
 *
 * 0    4    8    12   16   20   24   28
 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
 *
 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
 * FIXME: the top 17 bits of BR2.
 */

#define CONFIG_SYS_BR2_PRELIM		0xf0001861

/*
 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
 *
 * For OR2, need:
 *    64MB mask for AM, OR2[0:7] = 1111 1100
 *		   XAM, OR2[17:18] = 11
 *    9 columns OR2[19-21] = 010
 *    13 rows   OR2[23-25] = 100
 *    EAD set for extra time OR[31] = 1
 *
 * 0    4    8    12   16   20   24   28
 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
 */

#define CONFIG_SYS_OR2_PRELIM		0xfc006901

#define CONFIG_SYS_LBC_LCRR		0x00030004    /* LB clock ratio reg */
#define CONFIG_SYS_LBC_LBCR		0x00000000    /* LB config reg */
#define CONFIG_SYS_LBC_LSRT		0x20000000    /* LB sdram refresh timer */
#define CONFIG_SYS_LBC_MRTPR		0x20000000    /* LB refresh timer prescal*/

#define CONFIG_SYS_LBC_LSDMR_COMMON	( LSDMR_BSMA1516	\
				| LSDMR_RFCR5		\
				| LSDMR_PRETOACT3	\
				| LSDMR_ACTTORW3	\
				| LSDMR_BL8		\
				| LSDMR_WRC2		\
				| LSDMR_CL3		\
				| LSDMR_RFEN		\
				)

/*
 * SDRAM Controller configuration sequence.
 */
#define CONFIG_SYS_LBC_LSDMR_1	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
#define CONFIG_SYS_LBC_LSDMR_2	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
#define CONFIG_SYS_LBC_LSDMR_3	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
#define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
#define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)

/*
 * 32KB, 8-bit wide for ADS config reg
 */
#define CONFIG_SYS_BR4_PRELIM          0xf8000801
#define CONFIG_SYS_OR4_PRELIM		0xffffe1f1
#define CONFIG_SYS_BCSR		(CONFIG_SYS_BR4_PRELIM & 0xffff8000)

#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)    /* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)    /* Reserved for malloc */

/* Serial Port */
#define CONFIG_CONS_ON_SCC	/* define if console on SCC */
#undef  CONFIG_CONS_NONE	/* define if console on something else */
#define CONFIG_CONS_INDEX       1  /* which serial channel for console */

#define CONFIG_BAUDRATE		115200

#define CONFIG_SYS_BAUDRATE_TABLE  \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

/*
 * I2C
 */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }

/* RapidIO MMU */
#define CONFIG_SYS_RIO_MEM_VIRT	0xc0000000	/* base address */
#define CONFIG_SYS_RIO_MEM_BUS	0xc0000000	/* base address */
#define CONFIG_SYS_RIO_MEM_PHYS	0xc0000000
#define CONFIG_SYS_RIO_MEM_SIZE	0x20000000	/* 128M */

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */
#define CONFIG_SYS_PCI1_MEM_VIRT	0x80000000
#define CONFIG_SYS_PCI1_MEM_BUS	0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS	0x80000000
#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCI1_IO_VIRT	0xe2000000
#define CONFIG_SYS_PCI1_IO_BUS	0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS	0xe2000000
#define CONFIG_SYS_PCI1_IO_SIZE	0x100000	/* 1M */

#if defined(CONFIG_PCI)

#define CONFIG_PCI_PNP			/* do pci plug-and-play */

#undef CONFIG_EEPRO100
#undef CONFIG_TULIP

#if !defined(CONFIG_PCI_PNP)
    #define PCI_ENET0_IOADDR	0xe0000000
    #define PCI_ENET0_MEMADDR	0xe0000000
    #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
#endif

#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */

#endif	/* CONFIG_PCI */

#ifdef CONFIG_TSEC_ENET

#ifndef CONFIG_MII
#define CONFIG_MII		1	/* MII PHY management */
#endif
#define CONFIG_TSEC1	1
#define CONFIG_TSEC1_NAME	"TSEC0"
#define CONFIG_TSEC2	1
#define CONFIG_TSEC2_NAME	"TSEC1"
#define TSEC1_PHY_ADDR		0
#define TSEC2_PHY_ADDR		1
#define TSEC1_PHYIDX		0
#define TSEC2_PHYIDX		0
#define TSEC1_FLAGS		TSEC_GIGABIT
#define TSEC2_FLAGS		TSEC_GIGABIT

/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME		"TSEC0"

#endif /* CONFIG_TSEC_ENET */

#ifdef CONFIG_ETHER_ON_FCC		/* CPM FCC Ethernet */

#undef  CONFIG_ETHER_NONE		/* define if ether on something else */
#define CONFIG_ETHER_INDEX      2       /* which channel for ether */

#if (CONFIG_ETHER_INDEX == 2)
  /*
   * - Rx-CLK is CLK13
   * - Tx-CLK is CLK14
   * - Select bus for bd/buffers
   * - Full duplex
   */
  #define CONFIG_SYS_CMXFCR_MASK2      (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
  #define CONFIG_SYS_CMXFCR_VALUE2     (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
  #define CONFIG_SYS_CPMFCR_RAMTYPE    0
  #define CONFIG_SYS_FCC_PSMR          (FCC_PSMR_FDE)
  #define FETH2_RST		0x01
#elif (CONFIG_ETHER_INDEX == 3)
  /* need more definitions here for FE3 */
  #define FETH3_RST		0x80
#endif					/* CONFIG_ETHER_INDEX */

#ifndef CONFIG_MII
#define CONFIG_MII		1	/* MII PHY management */
#endif

#define CONFIG_BITBANGMII		/* bit-bang MII PHY management */

/*
 * GPIO pins used for bit-banged MII communications
 */
#define MDIO_PORT	2		/* Port C */
#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ( \
				(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
#define MDC_DECLARE	MDIO_DECLARE

#define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
#define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
#define MDIO_READ	((iop->pdat &  0x00400000) != 0)

#define MDIO(bit)	if(bit) iop->pdat |=  0x00400000; \
			else	iop->pdat &= ~0x00400000

#define MDC(bit)	if(bit) iop->pdat |=  0x00200000; \
			else	iop->pdat &= ~0x00200000

#define MIIDELAY	udelay(1)

#endif

/*
 * Environment
 */
#ifndef CONFIG_SYS_RAMBOOT
  #define CONFIG_ENV_IS_IN_FLASH	1
  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
  #define CONFIG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
  #define CONFIG_ENV_SIZE		0x2000
#else
  #define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
  #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
  #define CONFIG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO

#if defined(CONFIG_PCI)
    #define CONFIG_CMD_PCI
#endif

#if defined(CONFIG_ETHER_ON_FCC)
#endif

#undef CONFIG_WATCHDOG			/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR	0x1000000	/* default load address */

#if defined(CONFIG_CMD_KGDB)
    #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
#else
    #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
#endif

#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#endif

/*
 * Environment Configuration
 */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#endif

#define CONFIG_IPADDR    192.168.1.253

#define CONFIG_HOSTNAME		unknown
#define CONFIG_ROOTPATH		"/nfsroot"
#define CONFIG_BOOTFILE		"your.uImage"

#define CONFIG_SERVERIP  192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK   255.255.255.0

#define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */

#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */

#define CONFIG_BAUDRATE	115200

#define	CONFIG_EXTRA_ENV_SETTINGS				        \
	"netdev=eth0\0"							\
	"consoledev=ttyCPM\0"						\
	"ramdiskaddr=1000000\0"						\
	"ramdiskfile=your.ramdisk.u-boot\0"				\
	"fdtaddr=400000\0"						\
	"fdtfile=mpc8560ads.dtb\0"

#define CONFIG_NFSBOOTCOMMAND	                                        \
	"setenv bootargs root=/dev/nfs rw "				\
		"nfsroot=$serverip:$rootpath "				\
		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw "				\
		"console=$consoledev,$baudrate $othbootargs;"		\
	"tftp $ramdiskaddr $ramdiskfile;"				\
	"tftp $loadaddr $bootfile;"					\
	"tftp $fdtaddr $fdtfile;"					\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND

#endif	/* __CONFIG_H */
Commit	Line	Data
42d1f039	1	/*
7c57f3e8	2	* Copyright 2004, 2011 Freescale Semiconductor.
42d1f039 WD	3	* (C) Copyright 2002,2003 Motorola,Inc.
	4	* Xianghua Xiao <X.Xiao@motorola.com>
	5	*
3765b3e7	6	* SPDX-License-Identifier: GPL-2.0+
42d1f039 WD	7	*/
42d1f039 WD	8
0ac6f8b7 WD	9	/*
	10	* mpc8560ads board configuration file
	11	*
	12	* Please refer to doc/README.mpc85xx for more info.
	13	*
	14	* Make sure you change the MAC address and other network params first,
92ac5208	15	* search for CONFIG_SERVERIP, etc. in this file.
42d1f039 WD	16	*/
	17
	18	#ifndef __CONFIG_H
	19	#define __CONFIG_H
	20
	21	/* High Level Configuration Options */
0ac6f8b7 WD	22	#define CONFIG_BOOKE 1 /* BOOKE */
0ac6f8b7 WD	23	#define CONFIG_E500 1 /* BOOKE e500 family */
9c4c5ae3	24	#define CONFIG_CPM2 1 /* has CPM2 */
0ac6f8b7	25	#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
f060054d	26	#define CONFIG_MPC8560 1
0ac6f8b7	27
2ae18241 WD	28	/*
	29	* default CCARBAR is at 0xff700000
	30	* assume U-Boot is less than 0.5MB
	31	*/
	32	#define CONFIG_SYS_TEXT_BASE 0xfff80000
	33
842033e6	34	#define CONFIG_PCI_INDIRECT_BRIDGE
0151cbac	35	#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
53677ef1	36	#define CONFIG_TSEC_ENET /* tsec ethernet support */
ccc091aa	37	#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
42d1f039	38	#define CONFIG_ENV_OVERWRITE
7232a272	39	#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
004eca0c	40	#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
42d1f039	41
0ac6f8b7 WD	42	/*
	43	* sysclk for MPC85xx
	44	*
	45	* Two valid values are:
	46	* 33000000
	47	* 66000000
	48	*
	49	* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
9aea9530 WD	50	* is likely the desired value here, so that is now the default.
	51	* The board, however, can run at 66MHz. In any event, this value
	52	* must match the settings of some switches. Details can be found
	53	* in the README.mpc85xxads.
0ac6f8b7 WD	54	*/
0ac6f8b7 WD	55
9aea9530 WD	56	#ifndef CONFIG_SYS_CLK_FREQ
9aea9530 WD	57	#define CONFIG_SYS_CLK_FREQ 33000000
42d1f039 WD	58	#endif
42d1f039 WD	59
0ac6f8b7 WD	60	/*
	61	* These can be toggled for performance analysis, otherwise use default.
	62	*/
	63	#define CONFIG_L2_CACHE /* toggle L2 cache */
	64	#define CONFIG_BTB /* toggle branch predition */
42d1f039	65
6d0f6bcf	66	#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
0ac6f8b7	67
6d0f6bcf JCPV	68	#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
6d0f6bcf JCPV	69	#define CONFIG_SYS_MEMTEST_END 0x00400000
42d1f039	70
e46fedfe TT	71	#define CONFIG_SYS_CCSRBAR 0xe0000000
e46fedfe TT	72	#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
42d1f039	73
8b625114	74	/* DDR Setup */
5614e71b	75	#define CONFIG_SYS_FSL_DDR1
8b625114 JL	76	#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
	77	#define CONFIG_DDR_SPD
	78	#undef CONFIG_FSL_DDR_INTERACTIVE
	79
	80	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
9aea9530	81
6d0f6bcf JCPV	82	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
6d0f6bcf JCPV	83	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
9aea9530	84
8b625114 JL	85	#define CONFIG_NUM_DDR_CONTROLLERS 1
	86	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	87	#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
9aea9530	88
8b625114 JL	89	/* I2C addresses of SPD EEPROMs */
8b625114 JL	90	#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
9aea9530	91
8b625114	92	/* These are used when DDR doesn't use SPD. */
6d0f6bcf JCPV	93	#define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */
	94	#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
	95	#define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002
	96	#define CONFIG_SYS_DDR_TIMING_1 0x37344321
	97	#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
	98	#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
	99	#define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
	100	#define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
42d1f039	101
0ac6f8b7 WD	102	/*
	103	* SDRAM on the Local Bus
	104	*/
6d0f6bcf JCPV	105	#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
6d0f6bcf JCPV	106	#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
42d1f039	107
6d0f6bcf JCPV	108	#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */
6d0f6bcf JCPV	109	#define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */
42d1f039	110
6d0f6bcf JCPV	111	#define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
	112	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	113	#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */
	114	#undef CONFIG_SYS_FLASH_CHECKSUM
	115	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	116	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
0ac6f8b7	117
14d0a02a	118	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
42d1f039	119
6d0f6bcf JCPV	120	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
6d0f6bcf JCPV	121	#define CONFIG_SYS_RAMBOOT
42d1f039	122	#else
6d0f6bcf	123	#undef CONFIG_SYS_RAMBOOT
42d1f039 WD	124	#endif
42d1f039 WD	125
00b1883a	126	#define CONFIG_FLASH_CFI_DRIVER
6d0f6bcf JCPV	127	#define CONFIG_SYS_FLASH_CFI
6d0f6bcf JCPV	128	#define CONFIG_SYS_FLASH_EMPTY_INFO
0ac6f8b7 WD	129
0ac6f8b7 WD	130	#undef CONFIG_CLOCKS_IN_MHZ
42d1f039	131
0ac6f8b7 WD	132	/*
	133	* Local Bus Definitions
	134	*/
	135
	136	/*
	137	* Base Register 2 and Option Register 2 configure SDRAM.
6d0f6bcf	138	* The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
0ac6f8b7 WD	139	*
	140	* For BR2, need:
	141	* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
	142	* port-size = 32-bits = BR2[19:20] = 11
	143	* no parity checking = BR2[21:22] = 00
	144	* SDRAM for MSEL = BR2[24:26] = 011
	145	* Valid = BR[31] = 1
	146	*
	147	* 0 4 8 12 16 20 24 28
	148	* 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
	149	*
6d0f6bcf	150	* FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
0ac6f8b7 WD	151	* FIXME: the top 17 bits of BR2.
	152	*/
	153
6d0f6bcf	154	#define CONFIG_SYS_BR2_PRELIM 0xf0001861
0ac6f8b7 WD	155
0ac6f8b7 WD	156	/*
6d0f6bcf	157	* The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
0ac6f8b7 WD	158	*
	159	* For OR2, need:
	160	* 64MB mask for AM, OR2[0:7] = 1111 1100
	161	* XAM, OR2[17:18] = 11
	162	* 9 columns OR2[19-21] = 010
	163	* 13 rows OR2[23-25] = 100
	164	* EAD set for extra time OR[31] = 1
	165	*
	166	* 0 4 8 12 16 20 24 28
	167	* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
	168	*/
	169
6d0f6bcf	170	#define CONFIG_SYS_OR2_PRELIM 0xfc006901
0ac6f8b7	171
6d0f6bcf JCPV	172	#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
	173	#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
	174	#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
	175	#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
0ac6f8b7	176
b0fe93ed KG	177	#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_BSMA1516 \
	178	\| LSDMR_RFCR5 \
	179	\| LSDMR_PRETOACT3 \
	180	\| LSDMR_ACTTORW3 \
	181	\| LSDMR_BL8 \
	182	\| LSDMR_WRC2 \
	183	\| LSDMR_CL3 \
	184	\| LSDMR_RFEN \
0ac6f8b7 WD	185	)
	186
	187	/*
	188	* SDRAM Controller configuration sequence.
	189	*/
b0fe93ed KG	190	#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_PCHALL)
	191	#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_ARFRSH)
	192	#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_ARFRSH)
	193	#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_MRW)
	194	#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_NORMAL)
0ac6f8b7	195
9aea9530 WD	196	/*
	197	* 32KB, 8-bit wide for ADS config reg
	198	*/
6d0f6bcf JCPV	199	#define CONFIG_SYS_BR4_PRELIM 0xf8000801
	200	#define CONFIG_SYS_OR4_PRELIM 0xffffe1f1
	201	#define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000)
42d1f039	202
6d0f6bcf JCPV	203	#define CONFIG_SYS_INIT_RAM_LOCK 1
6d0f6bcf JCPV	204	#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
553f0982	205	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
42d1f039	206
25ddd1fb	207	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	208	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
42d1f039	209
6d0f6bcf JCPV	210	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
6d0f6bcf JCPV	211	#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
42d1f039 WD	212
42d1f039 WD	213	/* Serial Port */
0ac6f8b7 WD	214	#define CONFIG_CONS_ON_SCC /* define if console on SCC */
	215	#undef CONFIG_CONS_NONE /* define if console on something else */
	216	#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
42d1f039	217
53677ef1	218	#define CONFIG_BAUDRATE 115200
42d1f039	219
6d0f6bcf	220	#define CONFIG_SYS_BAUDRATE_TABLE \
42d1f039 WD	221	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
42d1f039 WD	222
20476726 JL	223	/*
	224	* I2C
	225	*/
00f792e0 HS	226	#define CONFIG_SYS_I2C
	227	#define CONFIG_SYS_I2C_FSL
	228	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	229	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	230	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	231	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
42d1f039	232
0ac6f8b7	233	/* RapidIO MMU */
5af0fdd8	234	#define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */
10795f42	235	#define CONFIG_SYS_RIO_MEM_BUS 0xc0000000 /* base address */
5af0fdd8	236	#define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000
6d0f6bcf	237	#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */
0ac6f8b7 WD	238
	239	/*
	240	* General PCI
362dd830	241	* Memory space is mapped 1-1, but I/O space must start from 0.
0ac6f8b7	242	*/
5af0fdd8	243	#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
10795f42	244	#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
5af0fdd8	245	#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
6d0f6bcf	246	#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
aca5f018	247	#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
5f91ef6a	248	#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
6d0f6bcf JCPV	249	#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
6d0f6bcf JCPV	250	#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
0ac6f8b7 WD	251
0ac6f8b7 WD	252	#if defined(CONFIG_PCI)
42d1f039	253
53677ef1	254	#define CONFIG_PCI_PNP /* do pci plug-and-play */
0ac6f8b7 WD	255
0ac6f8b7 WD	256	#undef CONFIG_EEPRO100
42d1f039	257	#undef CONFIG_TULIP
0ac6f8b7 WD	258
	259	#if !defined(CONFIG_PCI_PNP)
	260	#define PCI_ENET0_IOADDR 0xe0000000
	261	#define PCI_ENET0_MEMADDR 0xe0000000
53677ef1	262	#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
42d1f039	263	#endif
0ac6f8b7 WD	264
0ac6f8b7 WD	265	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
6d0f6bcf	266	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
0ac6f8b7 WD	267
	268	#endif /* CONFIG_PCI */
	269
ccc091aa	270	#ifdef CONFIG_TSEC_ENET
0ac6f8b7	271
ccc091aa	272	#ifndef CONFIG_MII
0ac6f8b7	273	#define CONFIG_MII 1 /* MII PHY management */
ccc091aa	274	#endif
255a3577 KP	275	#define CONFIG_TSEC1 1
	276	#define CONFIG_TSEC1_NAME "TSEC0"
	277	#define CONFIG_TSEC2 1
	278	#define CONFIG_TSEC2_NAME "TSEC1"
0ac6f8b7 WD	279	#define TSEC1_PHY_ADDR 0
	280	#define TSEC2_PHY_ADDR 1
	281	#define TSEC1_PHYIDX 0
	282	#define TSEC2_PHYIDX 0
3a79013e AF	283	#define TSEC1_FLAGS TSEC_GIGABIT
3a79013e AF	284	#define TSEC2_FLAGS TSEC_GIGABIT
d9b94f28 JL	285
	286	/* Options are: TSEC[0-1] */
	287	#define CONFIG_ETHPRIME "TSEC0"
0ac6f8b7	288
ccc091aa AF	289	#endif /* CONFIG_TSEC_ENET */
ccc091aa AF	290
53677ef1	291	#ifdef CONFIG_ETHER_ON_FCC /* CPM FCC Ethernet */
0ac6f8b7	292
53677ef1	293	#undef CONFIG_ETHER_NONE /* define if ether on something else */
0ac6f8b7 WD	294	#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
	295
	296	#if (CONFIG_ETHER_INDEX == 2)
42d1f039 WD	297	/*
	298	* - Rx-CLK is CLK13
	299	* - Tx-CLK is CLK14
	300	* - Select bus for bd/buffers
	301	* - Full duplex
	302	*/
d4590da4 MF	303	#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 \| CMXFCR_RF2CS_MSK \| CMXFCR_TF2CS_MSK)
d4590da4 MF	304	#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 \| CMXFCR_TF2CS_CLK14)
6d0f6bcf JCPV	305	#define CONFIG_SYS_CPMFCR_RAMTYPE 0
6d0f6bcf JCPV	306	#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
42d1f039	307	#define FETH2_RST 0x01
0ac6f8b7	308	#elif (CONFIG_ETHER_INDEX == 3)
42d1f039 WD	309	/* need more definitions here for FE3 */
42d1f039 WD	310	#define FETH3_RST 0x80
53677ef1	311	#endif /* CONFIG_ETHER_INDEX */
0ac6f8b7	312
ccc091aa AF	313	#ifndef CONFIG_MII
	314	#define CONFIG_MII 1 /* MII PHY management */
	315	#endif
	316
0ac6f8b7 WD	317	#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
0ac6f8b7 WD	318
42d1f039 WD	319	/*
	320	* GPIO pins used for bit-banged MII communications
	321	*/
	322	#define MDIO_PORT 2 /* Port C */
be225442 LCM	323	#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
	324	(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
	325	#define MDC_DECLARE MDIO_DECLARE
	326
42d1f039 WD	327	#define MDIO_ACTIVE (iop->pdir \|= 0x00400000)
	328	#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
	329	#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
	330
	331	#define MDIO(bit) if(bit) iop->pdat \|= 0x00400000; \
	332	else iop->pdat &= ~0x00400000
	333
	334	#define MDC(bit) if(bit) iop->pdat \|= 0x00200000; \
	335	else iop->pdat &= ~0x00200000
	336
	337	#define MIIDELAY udelay(1)
0ac6f8b7	338
42d1f039 WD	339	#endif
42d1f039 WD	340
0ac6f8b7 WD	341	/*
	342	* Environment
	343	*/
6d0f6bcf	344	#ifndef CONFIG_SYS_RAMBOOT
5a1aceb0	345	#define CONFIG_ENV_IS_IN_FLASH 1
6d0f6bcf	346	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
0e8d1586 JCPV	347	#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
0e8d1586 JCPV	348	#define CONFIG_ENV_SIZE 0x2000
42d1f039	349	#else
6d0f6bcf	350	#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
93f6d725	351	#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
6d0f6bcf	352	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
0e8d1586	353	#define CONFIG_ENV_SIZE 0x2000
42d1f039 WD	354	#endif
42d1f039 WD	355
0ac6f8b7	356	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
6d0f6bcf	357	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
42d1f039	358
659e2f67 JL	359	/*
	360	* BOOTP options
	361	*/
	362	#define CONFIG_BOOTP_BOOTFILESIZE
	363	#define CONFIG_BOOTP_BOOTPATH
	364	#define CONFIG_BOOTP_GATEWAY
	365	#define CONFIG_BOOTP_HOSTNAME
	366
2835e518 JL	367	/*
	368	* Command line configuration.
	369	*/
1c9aa76b	370	#define CONFIG_CMD_IRQ
199e262e	371	#define CONFIG_CMD_REGINFO
2835e518 JL	372
	373	#if defined(CONFIG_PCI)
	374	#define CONFIG_CMD_PCI
	375	#endif
	376
	377	#if defined(CONFIG_ETHER_ON_FCC)
2835e518 JL	378	#endif
2835e518 JL	379
0ac6f8b7	380	#undef CONFIG_WATCHDOG /* watchdog disabled */
42d1f039 WD	381
	382	/*
	383	* Miscellaneous configurable options
	384	*/
6d0f6bcf	385	#define CONFIG_SYS_LONGHELP /* undef to save memory */
5be58f5f KP	386	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
5be58f5f KP	387	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
6d0f6bcf	388	#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
0ac6f8b7	389
2835e518	390	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	391	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
42d1f039	392	#else
6d0f6bcf	393	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
42d1f039	394	#endif
0ac6f8b7	395
6d0f6bcf JCPV	396	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	397	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	398	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
42d1f039 WD	399
	400	/*
	401	* For booting Linux, the board info and command line data
a832ac41	402	* have to be in the first 64 MB of memory, since this is
42d1f039 WD	403	* the maximum mapped by the Linux kernel during initialization.
42d1f039 WD	404	*/
a832ac41 KG	405	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
a832ac41 KG	406	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
42d1f039	407
2835e518	408	#if defined(CONFIG_CMD_KGDB)
42d1f039	409	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
42d1f039 WD	410	#endif
42d1f039 WD	411
9aea9530 WD	412	/*
	413	* Environment Configuration
	414	*/
42d1f039	415	#if defined(CONFIG_TSEC_ENET) \|\| defined(CONFIG_ETHER_ON_FCC)
10327dc5	416	#define CONFIG_HAS_ETH0
e2ffd59b	417	#define CONFIG_HAS_ETH1
e2ffd59b	418	#define CONFIG_HAS_ETH2
5ce71580	419	#define CONFIG_HAS_ETH3
42d1f039 WD	420	#endif
42d1f039 WD	421
0ac6f8b7 WD	422	#define CONFIG_IPADDR 192.168.1.253
	423
	424	#define CONFIG_HOSTNAME unknown
8b3637c6	425	#define CONFIG_ROOTPATH "/nfsroot"
b3f44c21	426	#define CONFIG_BOOTFILE "your.uImage"
0ac6f8b7 WD	427
	428	#define CONFIG_SERVERIP 192.168.1.1
	429	#define CONFIG_GATEWAYIP 192.168.1.1
	430	#define CONFIG_NETMASK 255.255.255.0
	431
	432	#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
	433
0ac6f8b7 WD	434	#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
	435
	436	#define CONFIG_BAUDRATE 115200
	437
9aea9530	438	#define CONFIG_EXTRA_ENV_SETTINGS \
6b44a44e AF	439	"netdev=eth0\0" \
	440	"consoledev=ttyCPM\0" \
	441	"ramdiskaddr=1000000\0" \
	442	"ramdiskfile=your.ramdisk.u-boot\0" \
	443	"fdtaddr=400000\0" \
	444	"fdtfile=mpc8560ads.dtb\0"
0ac6f8b7	445
9aea9530	446	#define CONFIG_NFSBOOTCOMMAND \
6b44a44e AF	447	"setenv bootargs root=/dev/nfs rw " \
	448	"nfsroot=$serverip:$rootpath " \
	449	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	450	"console=$consoledev,$baudrate $othbootargs;" \
	451	"tftp $loadaddr $bootfile;" \
	452	"tftp $fdtaddr $fdtfile;" \
	453	"bootm $loadaddr - $fdtaddr"
0ac6f8b7 WD	454
0ac6f8b7 WD	455	#define CONFIG_RAMBOOTCOMMAND \
6b44a44e AF	456	"setenv bootargs root=/dev/ram rw " \
	457	"console=$consoledev,$baudrate $othbootargs;" \
	458	"tftp $ramdiskaddr $ramdiskfile;" \
	459	"tftp $loadaddr $bootfile;" \
	460	"tftp $fdtaddr $fdtfile;" \
	461	"bootm $loadaddr $ramdiskaddr $fdtaddr"
0ac6f8b7 WD	462
0ac6f8b7 WD	463	#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
42d1f039 WD	464
42d1f039 WD	465	#endif /* __CONFIG_H */