[people/ms/u-boot.git] / include / configs / PLU405.h

/*
 * (C) Copyright 2001-2003
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
#define CONFIG_PLU405		1	/* ...on a PLU405 board		*/

#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/

#define CONFIG_SYS_CLK_FREQ     33333400 /* external frequency to pll   */

#define CONFIG_BAUDRATE		9600

#undef	CONFIG_BOOTARGS
#undef	CONFIG_BOOTCOMMAND

#define CONFIG_PREBOOT                  /* enable preboot variable      */

#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

#define CONFIG_NET_MULTI	1
#undef  CONFIG_HAS_ETH1

#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII		1	/* MII PHY management		*/
#define CONFIG_PHY_ADDR		0	/* PHY address			*/
#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R      1       /* use reset_phy()              */

#define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_IDE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_ELF
#define CONFIG_CMD_NAND
#define CONFIG_CMD_DATE
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_USB

#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP

#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

#define CONFIG_SUPPORT_VFAT

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

#define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
#define CONFIG_SYS_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address		*/

#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/

#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
#ifdef	CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
#endif

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/

#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/

#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD	    691200
#undef	CONFIG_UART1_CONSOLE		/* define for uart1 as console	*/

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE	\
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
	 57600, 115200, 230400, 460800, 921600 }

#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */

#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */

#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

/* Only interrupt boot if space is pressed */
/* If a long serial cable is connected but */
/* other end is dead, garbage will be read */
#define CONFIG_AUTOBOOT_KEYED	1
#define CONFIG_AUTOBOOT_PROMPT	\
	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
#undef CONFIG_AUTOBOOT_DELAY_STR
#define CONFIG_AUTOBOOT_STOP_STR " "

#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */

#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */

/*
 * NAND-FLASH stuff
 */
#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
#define NAND_BIG_DELAY_US	25

#define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
#define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
#define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
#define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */

#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
#define CONFIG_SYS_NAND_QUIET          1

/*
 * PCI stuff
 */
#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
#define PCI_HOST_FORCE  1               /* configure as pci host        */
#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

#define CONFIG_PCI			/* include pci support	        */
#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
					/* resource configuration       */

#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */

#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
#define CONFIG_SYS_PCI_PTM1MS  0xf8000001      /* 128MB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
#define CONFIG_SYS_PCI_PTM2PCI 0x08000000      /* Host: use this pci address   */

/*
 * IDE/ATA stuff
 */
#undef	CONFIG_IDE_8xx_DIRECT		    /* no pcmcia interface required */
#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
#define CONFIG_IDE_RESET	1	/* reset for ide supported	*/

#define CONFIG_SYS_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
/* max. 1 drives per IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*1)

#define CONFIG_SYS_ATA_BASE_ADDR	0xF0100000
#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
#define CONFIG_SYS_ATA_REG_OFFSET	0x0000	/* Offset for normal register access */
#define CONFIG_SYS_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */

/*
 * FLASH organization
 */
#define FLASH_BASE0_PRELIM	0xFFC00000 /* FLASH bank #0 */

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms) */

#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width) */
#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st addr for flash config cycles */
#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd addr for flash config cycles */
/*
 * The following defines are added for buggy IOP480 byte interface.
 * All other boards should use the standard values (CPCI405 etc.)
 */
#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard */
#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard */
#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard */

#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector */

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE		TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN		(~(TEXT_BASE) + 1)
#define CONFIG_SYS_MALLOC_LEN		(1024 << 10)

/*
 * Environment Variable setup
 */
#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET		0x100	/* reseve 0x100 bytes for strapping */
#define CONFIG_ENV_SIZE		0x700

/*
 * I2C EEPROM (24WC16) for environment
 */
#define CONFIG_HARD_I2C			/* I2c with hardware support */
#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE		0x7F

#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM 24WC16 */
#define CONFIG_SYS_EEPROM_WREN         1

/* 24WC16 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
/* mask of address bits that overflow into the "EEPROM chip address"    */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The 24WC16 has   */
					/* 16 byte page write mode using */
					/* last 4 bits of the address   */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */

/*
 * External Bus Controller (EBC) Setup
 */
#define CAN0_BA		0xF0000000	    /* CAN0 Base Address	*/
#define CAN1_BA		0xF0000100	    /* CAN1 Base Address	*/
#define DUART0_BA	0xF0000400	    /* DUART Base Address       */
#define DUART1_BA	0xF0000408	    /* DUART Base Address       */
#define RTC_BA		0xF0000500	    /* RTC Base Address         */
#define VGA_BA		0xF1000000	    /* Epson VGA Base Address   */
#define CONFIG_SYS_NAND_BASE	0xF4000000	    /* NAND FLASH Base Address  */

/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
/* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
#define CONFIG_SYS_EBC_PB0AP		0x92015480
/* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000

/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB1AP		0x92015480
/* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB1CR		0xF4018000

/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB2AP		0x010053C0
/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB2CR		0xF0018000

/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB3AP		0x010053C0
/* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB3CR		0xF011A000

/*
 * FPGA stuff
 */
#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100	    /* FPGA internal Base Address */

/* FPGA internal regs */
#define CONFIG_SYS_FPGA_CTRL		0x000

/* FPGA Control Reg */
#define CONFIG_SYS_FPGA_CTRL_CF_RESET	0x0001
#define CONFIG_SYS_FPGA_CTRL_WDI	0x0002
#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020

#define CONFIG_SYS_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now */
#define CONFIG_SYS_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/

/* FPGA program pin configuration */
#define CONFIG_SYS_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
#define CONFIG_SYS_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output) */
#define CONFIG_SYS_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output) */
#define CONFIG_SYS_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input) */
#define CONFIG_SYS_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input) */

/*
 * Definitions for initial stack pointer and data area (in data cache)
 */
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM	  1

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM  */

#define CONFIG_SYS_GBL_DATA_SIZE      128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Definitions for GPIO setup (PPC405EP specific)
 *
 * GPIO0[0]	- External Bus Controller BLAST output
 * GPIO0[1-9]	- Instruction trace outputs -> GPIO
 * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 * GPIO0[24-27] - UART0 control signal inputs/outputs
 * GPIO0[28-29] - UART1 data signal input/output
 * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 */
#define CONFIG_SYS_GPIO0_OSRL		0x00000550
#define CONFIG_SYS_GPIO0_OSRH		0x00000110
#define CONFIG_SYS_GPIO0_ISR1L		0x00000000
#define CONFIG_SYS_GPIO0_ISR1H		0x15555445
#define CONFIG_SYS_GPIO0_TSRL		0x00000000
#define CONFIG_SYS_GPIO0_TSRH		0x00000000
#define CONFIG_SYS_GPIO0_TCR		0x77FE0014

#define CONFIG_SYS_DUART_RST		(0x80000000 >> 14)
#define CONFIG_SYS_EEPROM_WP		(0x80000000 >> 0)

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM	0x02		/* Software reboot */

/*
 * Default speed selection (cpu_plb_opb_ebc) in MHz.
 * This value will be set if iic boot eprom is disabled.
 */
#if 1
#define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
#define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
#endif
#if 0
#define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
#define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
#endif
#if 0
#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
#endif

/*
 * PCI OHCI controller
 */
#define CONFIG_USB_OHCI_NEW	1
#define CONFIG_PCI_OHCI		1
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
#define CONFIG_USB_STORAGE	1

/*
 * UBI
 */
#define CONFIG_CMD_UBI
#define CONFIG_RBTREE
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO

#endif	/* __CONFIG_H */
Commit	Line	Data
13fdf8a6 SR	1	/*
	2	* (C) Copyright 2001-2003
	3	* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
	4	*
	5	* See file CREDITS for list of people who contributed to this
	6	* project.
	7	*
	8	* This program is free software; you can redistribute it and/or
	9	* modify it under the terms of the GNU General Public License as
	10	* published by the Free Software Foundation; either version 2 of
	11	* the License, or (at your option) any later version.
	12	*
	13	* This program is distributed in the hope that it will be useful,
	14	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	15	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	16	* GNU General Public License for more details.
	17	*
	18	* You should have received a copy of the GNU General Public License
	19	* along with this program; if not, write to the Free Software
	20	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	21	* MA 02111-1307 USA
	22	*/
	23
	24	/*
	25	* board/config.h - configuration options, board specific
	26	*/
	27
	28	#ifndef __CONFIG_H
	29	#define __CONFIG_H
	30
	31	/*
	32	* High Level Configuration Options
	33	* (easy to change)
	34	*/
	35
	36	#define CONFIG_405EP 1 /* This is a PPC405 CPU */
c837dcb1 WD	37	#define CONFIG_4xx 1 /* ...member of PPC4xx family */
c837dcb1 WD	38	#define CONFIG_PLU405 1 /* ...on a PLU405 board */
13fdf8a6	39
c837dcb1 WD	40	#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
c837dcb1 WD	41	#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
13fdf8a6	42
a20b27a3	43	#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
13fdf8a6 SR	44
13fdf8a6 SR	45	#define CONFIG_BAUDRATE 9600
13fdf8a6 SR	46
13fdf8a6 SR	47	#undef CONFIG_BOOTARGS
a20b27a3 SR	48	#undef CONFIG_BOOTCOMMAND
	49
	50	#define CONFIG_PREBOOT /* enable preboot variable */
	51
6d0f6bcf	52	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
13fdf8a6	53
a20b27a3	54	#define CONFIG_NET_MULTI 1
f9fc6a58	55	#undef CONFIG_HAS_ETH1
a20b27a3	56
96e21f86	57	#define CONFIG_PPC4xx_EMAC
13fdf8a6	58	#define CONFIG_MII 1 /* MII PHY management */
c837dcb1	59	#define CONFIG_PHY_ADDR 0 /* PHY address */
a20b27a3	60	#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
9ec367aa	61	#define CONFIG_RESET_PHY_R 1 /* use reset_phy() */
a20b27a3 SR	62
a20b27a3 SR	63	#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
13fdf8a6	64
acf02697	65
a1aa0bb5 JL	66	/*
	67	* BOOTP options
	68	*/
	69	#define CONFIG_BOOTP_BOOTFILESIZE
	70	#define CONFIG_BOOTP_BOOTPATH
	71	#define CONFIG_BOOTP_GATEWAY
	72	#define CONFIG_BOOTP_HOSTNAME
	73
	74
acf02697 JL	75	/*
	76	* Command line configuration.
	77	*/
	78	#include <config_cmd_default.h>
	79
	80	#define CONFIG_CMD_DHCP
	81	#define CONFIG_CMD_PCI
	82	#define CONFIG_CMD_IRQ
	83	#define CONFIG_CMD_IDE
	84	#define CONFIG_CMD_FAT
	85	#define CONFIG_CMD_ELF
	86	#define CONFIG_CMD_NAND
	87	#define CONFIG_CMD_DATE
	88	#define CONFIG_CMD_I2C
	89	#define CONFIG_CMD_MII
	90	#define CONFIG_CMD_PING
	91	#define CONFIG_CMD_EEPROM
17e65c21	92	#define CONFIG_CMD_USB
acf02697	93
3bc1054c MF	94	#define CONFIG_OF_LIBFDT
3bc1054c MF	95	#define CONFIG_OF_BOARD_SETUP
13fdf8a6 SR	96
	97	#define CONFIG_MAC_PARTITION
	98	#define CONFIG_DOS_PARTITION
	99
a20b27a3 SR	100	#define CONFIG_SUPPORT_VFAT
a20b27a3 SR	101
c837dcb1	102	#undef CONFIG_WATCHDOG /* watchdog disabled */
13fdf8a6	103
c837dcb1	104	#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
6d0f6bcf	105	#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
13fdf8a6	106
c837dcb1	107	#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
13fdf8a6 SR	108
	109	/*
	110	* Miscellaneous configurable options
	111	*/
6d0f6bcf JCPV	112	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6d0f6bcf JCPV	113	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
13fdf8a6	114
6d0f6bcf JCPV	115	#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
	116	#ifdef CONFIG_SYS_HUSH_PARSER
	117	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
13fdf8a6 SR	118	#endif
13fdf8a6 SR	119
acf02697	120	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	121	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
13fdf8a6	122	#else
6d0f6bcf	123	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
13fdf8a6	124	#endif
6d0f6bcf JCPV	125	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	126	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	127	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
13fdf8a6	128
6d0f6bcf	129	#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
13fdf8a6	130
6d0f6bcf	131	#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
13fdf8a6	132
a20b27a3 SR	133	#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
a20b27a3 SR	134
6d0f6bcf JCPV	135	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
6d0f6bcf JCPV	136	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
13fdf8a6	137
6d0f6bcf	138	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
6d0f6bcf	139	#define CONFIG_SYS_BASE_BAUD 691200
c837dcb1	140	#undef CONFIG_UART1_CONSOLE /* define for uart1 as console */
13fdf8a6 SR	141
13fdf8a6 SR	142	/* The following table includes the supported baudrates */
6d0f6bcf	143	#define CONFIG_SYS_BAUDRATE_TABLE \
13fdf8a6 SR	144	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
	145	57600, 115200, 230400, 460800, 921600 }
	146
6d0f6bcf JCPV	147	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6d0f6bcf JCPV	148	#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
13fdf8a6	149
6d0f6bcf	150	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
13fdf8a6	151
17e65c21	152	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
13fdf8a6	153	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
a20b27a3 SR	154	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
	155
	156	/* Only interrupt boot if space is pressed */
	157	/* If a long serial cable is connected but */
	158	/* other end is dead, garbage will be read */
f2302d44 SR	159	#define CONFIG_AUTOBOOT_KEYED 1
	160	#define CONFIG_AUTOBOOT_PROMPT \
	161	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
a20b27a3 SR	162	#undef CONFIG_AUTOBOOT_DELAY_STR
a20b27a3 SR	163	#define CONFIG_AUTOBOOT_STOP_STR " "
13fdf8a6	164
c837dcb1	165	#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
13fdf8a6	166
6d0f6bcf	167	#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
13fdf8a6	168
9ec367aa	169	/*
13fdf8a6	170	* NAND-FLASH stuff
13fdf8a6	171	*/
6d0f6bcf	172	#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
6d0f6bcf	173	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
bd84ee4c	174	#define NAND_BIG_DELAY_US 25
addb2e16	175
6d0f6bcf JCPV	176	#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
	177	#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
	178	#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
	179	#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
13fdf8a6	180
6d0f6bcf JCPV	181	#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
6d0f6bcf JCPV	182	#define CONFIG_SYS_NAND_QUIET 1
a20b27a3	183
9ec367aa	184	/*
13fdf8a6	185	* PCI stuff
13fdf8a6	186	*/
a20b27a3 SR	187	#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
	188	#define PCI_HOST_FORCE 1 /* configure as pci host */
	189	#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
	190
	191	#define CONFIG_PCI /* include pci support */
17e65c21	192	#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
a20b27a3 SR	193	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	194	/* resource configuration */
	195
	196	#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
	197
	198	#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
	199
6d0f6bcf JCPV	200	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
	201	#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
	202	#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
	203	#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
	204	#define CONFIG_SYS_PCI_PTM1MS 0xf8000001 /* 128MB, enable hard-wired to 1 */
	205	#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
	206	#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
	207	#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
	208	#define CONFIG_SYS_PCI_PTM2PCI 0x08000000 /* Host: use this pci address */
13fdf8a6	209
9ec367aa	210	/*
13fdf8a6	211	* IDE/ATA stuff
13fdf8a6	212	*/
c837dcb1 WD	213	#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
c837dcb1 WD	214	#undef CONFIG_IDE_LED /* no led for ide supported */
13fdf8a6 SR	215	#define CONFIG_IDE_RESET 1 /* reset for ide supported */
13fdf8a6 SR	216
6d0f6bcf	217	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
9ec367aa	218	/* max. 1 drives per IDE bus */
6d0f6bcf	219	#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1)
13fdf8a6	220
6d0f6bcf JCPV	221	#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
6d0f6bcf JCPV	222	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
13fdf8a6	223
6d0f6bcf JCPV	224	#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
	225	#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */
	226	#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
13fdf8a6 SR	227
	228	/*
	229	* For booting Linux, the board info and command line data
	230	* have to be in the first 8 MB of memory, since this is
	231	* the maximum mapped by the Linux kernel during initialization.
	232	*/
6d0f6bcf	233	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
9ec367aa MF	234
9ec367aa MF	235	/*
13fdf8a6 SR	236	* FLASH organization
13fdf8a6 SR	237	*/
9ec367aa	238	#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
13fdf8a6	239
6d0f6bcf JCPV	240	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
6d0f6bcf JCPV	241	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
13fdf8a6	242
6d0f6bcf JCPV	243	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	244	#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
13fdf8a6	245
6d0f6bcf JCPV	246	#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
	247	#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st addr for flash config cycles */
	248	#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd addr for flash config cycles */
13fdf8a6 SR	249	/*
	250	* The following defines are added for buggy IOP480 byte interface.
	251	* All other boards should use the standard values (CPCI405 etc.)
	252	*/
6d0f6bcf JCPV	253	#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
	254	#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
	255	#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
13fdf8a6	256
6d0f6bcf	257	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */
13fdf8a6	258
9ec367aa	259	/*
13fdf8a6 SR	260	* Start addresses for the final memory configuration
13fdf8a6 SR	261	* (Set up by the startup code)
6d0f6bcf	262	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
13fdf8a6	263	*/
6d0f6bcf	264	#define CONFIG_SYS_SDRAM_BASE 0x00000000
985edacc MF	265	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE
	266	#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
	267	#define CONFIG_SYS_MONITOR_LEN (~(TEXT_BASE) + 1)
	268	#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
13fdf8a6	269
9ec367aa	270	/*
13fdf8a6 SR	271	* Environment Variable setup
13fdf8a6 SR	272	*/
bb1f8b4f	273	#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
0e8d1586 JCPV	274	#define CONFIG_ENV_OFFSET 0x100 /* reseve 0x100 bytes for strapping */
0e8d1586 JCPV	275	#define CONFIG_ENV_SIZE 0x700
13fdf8a6	276
9ec367aa MF	277	/*
9ec367aa MF	278	* I2C EEPROM (24WC16) for environment
13fdf8a6 SR	279	*/
13fdf8a6 SR	280	#define CONFIG_HARD_I2C /* I2c with hardware support */
d0b0dcaa	281	#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
6d0f6bcf JCPV	282	#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
6d0f6bcf JCPV	283	#define CONFIG_SYS_I2C_SLAVE 0x7F
13fdf8a6	284
6d0f6bcf JCPV	285	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24WC16 */
6d0f6bcf JCPV	286	#define CONFIG_SYS_EEPROM_WREN 1
bd84ee4c	287
9ec367aa	288	/* 24WC16 */
6d0f6bcf	289	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
9ec367aa	290	/* mask of address bits that overflow into the "EEPROM chip address" */
6d0f6bcf JCPV	291	#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
6d0f6bcf JCPV	292	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The 24WC16 has */
9ec367aa MF	293	/* 16 byte page write mode using */
9ec367aa MF	294	/* last 4 bits of the address */
6d0f6bcf	295	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
13fdf8a6	296
9ec367aa	297	/*
13fdf8a6 SR	298	* External Bus Controller (EBC) Setup
13fdf8a6 SR	299	*/
be0db3e3 MF	300	#define CAN0_BA 0xF0000000 /* CAN0 Base Address */
be0db3e3 MF	301	#define CAN1_BA 0xF0000100 /* CAN1 Base Address */
9ec367aa MF	302	#define DUART0_BA 0xF0000400 /* DUART Base Address */
	303	#define DUART1_BA 0xF0000408 /* DUART Base Address */
	304	#define RTC_BA 0xF0000500 /* RTC Base Address */
	305	#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
6d0f6bcf	306	#define CONFIG_SYS_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
9ec367aa MF	307
	308	/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
	309	/* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
6d0f6bcf	310	#define CONFIG_SYS_EBC_PB0AP 0x92015480
9ec367aa	311	/* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
6d0f6bcf	312	#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000
13fdf8a6	313
9ec367aa	314	/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
6d0f6bcf	315	#define CONFIG_SYS_EBC_PB1AP 0x92015480
9ec367aa	316	/* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
6d0f6bcf	317	#define CONFIG_SYS_EBC_PB1CR 0xF4018000
13fdf8a6	318
9ec367aa MF	319	/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
9ec367aa MF	320	/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
6d0f6bcf	321	#define CONFIG_SYS_EBC_PB2AP 0x010053C0
9ec367aa	322	/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
6d0f6bcf	323	#define CONFIG_SYS_EBC_PB2CR 0xF0018000
13fdf8a6	324
9ec367aa MF	325	/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
9ec367aa MF	326	/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
6d0f6bcf	327	#define CONFIG_SYS_EBC_PB3AP 0x010053C0
9ec367aa	328	/* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
6d0f6bcf	329	#define CONFIG_SYS_EBC_PB3CR 0xF011A000
13fdf8a6	330
9ec367aa	331	/*
13fdf8a6 SR	332	* FPGA stuff
13fdf8a6 SR	333	*/
6d0f6bcf	334	#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
13fdf8a6 SR	335
13fdf8a6 SR	336	/* FPGA internal regs */
6d0f6bcf	337	#define CONFIG_SYS_FPGA_CTRL 0x000
13fdf8a6 SR	338
13fdf8a6 SR	339	/* FPGA Control Reg */
6d0f6bcf JCPV	340	#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001
	341	#define CONFIG_SYS_FPGA_CTRL_WDI 0x0002
	342	#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020
13fdf8a6	343
6d0f6bcf JCPV	344	#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
6d0f6bcf JCPV	345	#define CONFIG_SYS_FPGA_MAX_SIZE 1281024 / 128kByte is enough for XC2S50E*/
13fdf8a6 SR	346
13fdf8a6 SR	347	/* FPGA program pin configuration */
6d0f6bcf JCPV	348	#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
	349	#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
	350	#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
	351	#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
	352	#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
13fdf8a6	353
9ec367aa	354	/*
13fdf8a6 SR	355	* Definitions for initial stack pointer and data area (in data cache)
	356	*/
	357	/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
6d0f6bcf	358	#define CONFIG_SYS_TEMP_STACK_OCM 1
13fdf8a6 SR	359
13fdf8a6 SR	360	/* On Chip Memory location */
6d0f6bcf JCPV	361	#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
	362	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
	363	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
	364	#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
13fdf8a6	365
6d0f6bcf JCPV	366	#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
	367	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
	368	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
13fdf8a6	369
9ec367aa	370	/*
13fdf8a6 SR	371	* Definitions for GPIO setup (PPC405EP specific)
13fdf8a6 SR	372	*
c837dcb1 WD	373	* GPIO0[0] - External Bus Controller BLAST output
c837dcb1 WD	374	* GPIO0[1-9] - Instruction trace outputs -> GPIO
13fdf8a6 SR	375	* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
	376	* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
	377	* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
	378	* GPIO0[24-27] - UART0 control signal inputs/outputs
	379	* GPIO0[28-29] - UART1 data signal input/output
	380	* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
	381	*/
afabb498 SR	382	#define CONFIG_SYS_GPIO0_OSRL 0x00000550
	383	#define CONFIG_SYS_GPIO0_OSRH 0x00000110
	384	#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
	385	#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
6d0f6bcf	386	#define CONFIG_SYS_GPIO0_TSRL 0x00000000
afabb498	387	#define CONFIG_SYS_GPIO0_TSRH 0x00000000
6d0f6bcf	388	#define CONFIG_SYS_GPIO0_TCR 0x77FE0014
13fdf8a6	389
6d0f6bcf JCPV	390	#define CONFIG_SYS_DUART_RST (0x80000000 >> 14)
6d0f6bcf JCPV	391	#define CONFIG_SYS_EEPROM_WP (0x80000000 >> 0)
13fdf8a6 SR	392
	393	/*
	394	* Internal Definitions
	395	*
	396	* Boot Flags
	397	*/
9ec367aa MF	398	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
9ec367aa MF	399	#define BOOTFLAG_WARM 0x02 /* Software reboot */
13fdf8a6 SR	400
13fdf8a6 SR	401	/*
9ec367aa	402	* Default speed selection (cpu_plb_opb_ebc) in MHz.
13fdf8a6 SR	403	* This value will be set if iic boot eprom is disabled.
13fdf8a6 SR	404	*/
17e65c21	405	#if 1
c837dcb1 WD	406	#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
c837dcb1 WD	407	#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
13fdf8a6 SR	408	#endif
13fdf8a6 SR	409	#if 0
c837dcb1 WD	410	#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
c837dcb1 WD	411	#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
13fdf8a6	412	#endif
17e65c21	413	#if 0
c837dcb1 WD	414	#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
c837dcb1 WD	415	#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
13fdf8a6 SR	416	#endif
13fdf8a6 SR	417
17e65c21 MF	418	/*
	419	* PCI OHCI controller
	420	*/
	421	#define CONFIG_USB_OHCI_NEW 1
	422	#define CONFIG_PCI_OHCI 1
6d0f6bcf JCPV	423	#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
	424	#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
	425	#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
17e65c21 MF	426	#define CONFIG_USB_STORAGE 1
17e65c21 MF	427
985edacc MF	428	/*
	429	* UBI
	430	*/
	431	#define CONFIG_CMD_UBI
	432	#define CONFIG_RBTREE
	433	#define CONFIG_MTD_DEVICE
	434	#define CONFIG_MTD_PARTITIONS
	435	#define CONFIG_CMD_MTDPARTS
	436	#define CONFIG_LZO
	437
13fdf8a6	438	#endif /* __CONFIG_H */