[people/ms/u-boot.git] / include / configs / T4240QDS.h

/*
 * Copyright 2011-2012 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * T4240 QDS board configuration file
 */
#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_T4240QDS
#define CONFIG_PHYS_64BIT

#define CONFIG_FSL_SATA_V2
#define CONFIG_PCIE4

#define CONFIG_ICS307_REFCLK_HZ		25000000  /* ICS307 ref clk freq */

#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
#endif

#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_NO_FLASH
#endif

#define CONFIG_SRIO_PCIE_BOOT_MASTER
#define CONFIG_DDR_ECC

#include "t4qds.h"

#ifdef CONFIG_SYS_NO_FLASH
#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_ENV_IS_NOWHERE
#endif
#else
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif

#if defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS              0
#define CONFIG_ENV_SPI_CS               0
#define CONFIG_ENV_SPI_MAX_HZ           10000000
#define CONFIG_ENV_SPI_MODE             0
#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
#define CONFIG_ENV_SECT_SIZE            0x10000
#elif defined(CONFIG_SDCARD)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV          0
#define CONFIG_ENV_SIZE			0x2000
#define CONFIG_ENV_OFFSET		(512 * 1097)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_IN_REMOTE
#define CONFIG_ENV_ADDR		0xffe20000
#define CONFIG_ENV_SIZE		0x2000
#elif defined(CONFIG_ENV_IS_NOWHERE)
#define CONFIG_ENV_SIZE		0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE		0x2000
#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
#endif

#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk()
#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()

#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
unsigned long get_board_ddr_clk(void);
#endif

/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM	0
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1

/*
 * DDR Setup
 */
#define CONFIG_SYS_SPD_BUS_NUM	0
#define SPD_EEPROM_ADDRESS1	0x51
#define SPD_EEPROM_ADDRESS2	0x52
#define SPD_EEPROM_ADDRESS3	0x53
#define SPD_EEPROM_ADDRESS4	0x54
#define SPD_EEPROM_ADDRESS5	0x55
#define SPD_EEPROM_ADDRESS6	0x56
#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1	/* for p3041/p5010 */
#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */

/*
 * IFC Definitions
 */
#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
				+ 0x8000000) | \
				CSPR_PORT_SIZE_16 | \
				CSPR_MSEL_NOR | \
				CSPR_V)
#define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)
#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
				CSPR_PORT_SIZE_16 | \
				CSPR_MSEL_NOR | \
				CSPR_V)
#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80

#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
				FTIM0_NOR_TEADC(0x5) | \
				FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
				FTIM1_NOR_TRAD_NOR(0x1A) |\
				FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
				FTIM2_NOR_TCH(0x4) | \
				FTIM2_NOR_TWPH(0x0E) | \
				FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3	0x0

#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \
					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}

#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
#define QIXIS_BASE			0xffdf0000
#define QIXIS_LBMAP_SWITCH		6
#define QIXIS_LBMAP_MASK		0x0f
#define QIXIS_LBMAP_SHIFT		0
#define QIXIS_LBMAP_DFLTBANK		0x00
#define QIXIS_LBMAP_ALTBANK		0x04
#define QIXIS_RST_CTL_RESET		0x83
#define QIXIS_RST_FORCE_MEM		0x1
#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
#define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)

#define CONFIG_SYS_CSPR3_EXT	(0xf)
#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 \
				| CSPR_MSEL_GPCM \
				| CSPR_V)
#define CONFIG_SYS_AMASK3	IFC_AMASK(4*1024)
#define CONFIG_SYS_CSOR3	0x0
/* QIXIS Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
					FTIM0_GPCM_TEADC(0x0e) | \
					FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
					FTIM1_GPCM_TRAD(0x3f))
#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
					FTIM2_GPCM_TCH(0x0) | \
					FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS3_FTIM3		0x0

/* NAND Flash on IFC */
#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE		0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)

#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
				| CSPR_V)
#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)

#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \
				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/

#define CONFIG_SYS_NAND_ONFI_DETECTION

/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
					FTIM0_NAND_TWP(0x18)   | \
					FTIM0_NAND_TWCHT(0x07) | \
					FTIM0_NAND_TWH(0x0a))
#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
					FTIM1_NAND_TWBE(0x39)  | \
					FTIM1_NAND_TRR(0x0e)   | \
					FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
					FTIM2_NAND_TREH(0x0a) | \
					FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3		0x0

#define CONFIG_SYS_NAND_DDR_LAW		11

#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND

#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)

#if defined(CONFIG_NAND)
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
#else
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
#endif
#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3

#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif


/* I2C */
#define CONFIG_SYS_FSL_I2C_SPEED	100000	/* I2C speed */
#define CONFIG_SYS_FSL_I2C2_SPEED	100000	/* I2C2 speed */
#define I2C_MUX_PCA_ADDR_PRI		0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC		0x76 /* I2C bus multiplexer,secondary */

#define I2C_MUX_CH_DEFAULT	0x8
#define I2C_MUX_CH_VOL_MONITOR	0xa
#define I2C_MUX_CH_VSC3316_FS	0xc
#define I2C_MUX_CH_VSC3316_BS	0xd

/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR		0x40
#define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
#define I2C_VOL_MONITOR_BUS_V_OVF	0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT	3

/* VSC Crossbar switches */
#define CONFIG_VSC_CROSSBAR
#define VSC3316_FSM_TX_ADDR	0x70
#define VSC3316_FSM_RX_ADDR	0x71

/*
 * RapidIO
 */

/*
 * for slave u-boot IMAGE instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000	/* 512K */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
/*
 * for slave UCODE and ENV instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000	/* 256K */

/* slave core release by master*/
#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

/*
 * SRIO_PCIE_BOOT - SLAVE
 */
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif
/*
 * eSPI - Enhanced SPI
 */
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SST
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED         10000000
#define CONFIG_SF_DEFAULT_MODE          0


/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS	50
#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
#define CONFIG_SYS_QMAN_NUM_PORTALS	50
#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000

#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
#define CONFIG_SYS_PMAN
#define CONFIG_SYS_DPAA_DCE
#define CONFIG_SYS_INTERLAKEN

/* Default address of microcode for the Linux Fman driver */
#if defined(CONFIG_SPIFLASH)
/*
 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 * env, so we got 0x110000.
 */
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
#elif defined(CONFIG_SDCARD)
/*
 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 * about 545KB (1089 blocks), Env is stored after the image, and the env size is
 * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
 */
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
 * Slave has no ucode locally, it can fetch this from remote. When implementing
 * in two corenet boards, slave's ucode could be stored in master's memory
 * space, the address can be mapped from slave TLB->slave LAW->
 * slave SRIO or PCIE outbound window->master inbound window->
 * master LAW->the ucode address in master's memory space.
 */
#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */

#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_VITESSE
#define CONFIG_PHY_TERANETICS
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
#define FM1_10GEC1_PHY_ADDR	0x0
#define FM1_10GEC2_PHY_ADDR	0x1
#define FM2_10GEC1_PHY_ADDR	0x2
#define FM2_10GEC2_PHY_ADDR	0x3
#endif


/* SATA */
#ifdef CONFIG_FSL_SATA_V2
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA

#define CONFIG_SYS_SATA_MAX_DEVICE	2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA

#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#endif

#ifdef CONFIG_FMAN_ENET
#define CONFIG_MII		/* MII PHY management */
#define CONFIG_ETHPRIME		"FM1@DTSEC1"
#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
#endif

/*
* USB
*/
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_CMD_EXT2
#define CONFIG_HAS_FSL_DR_USB

#define CONFIG_MMC

#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif

#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */

#define __USB_PHY_TYPE	utmi

/*
 * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
 * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
 * interleaving. It can be cacheline, page, bank, superbank.
 * See doc/README.fsl-ddr for details.
 */
#ifdef CONFIG_PPC_T4240
#define CTRL_INTLV_PREFERED 3way_4KB
#else
#define CTRL_INTLV_PREFERED cacheline
#endif

#define	CONFIG_EXTRA_ENV_SETTINGS				\
	"hwconfig=fsl_ddr:"					\
	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
	"bank_intlv=auto;"					\
	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
	"netdev=eth0\0"						\
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"		\
	"tftpflash=tftpboot $loadaddr $uboot && "		\
	"protect off $ubootaddr +$filesize && "			\
	"erase $ubootaddr +$filesize && "			\
	"cp.b $loadaddr $ubootaddr $filesize && "		\
	"protect on $ubootaddr +$filesize && "			\
	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
	"consoledev=ttyS0\0"					\
	"ramdiskaddr=2000000\0"					\
	"ramdiskfile=t4240qds/ramdisk.uboot\0"			\
	"fdtaddr=c00000\0"					\
	"fdtfile=t4240qds/t4240qds.dtb\0"				\
	"bdev=sda3\0"						\
	"c=ffe\0"

#define CONFIG_HVBOOT				\
	"setenv bootargs config-addr=0x60000000; "	\
	"bootm 0x01000000 - 0x00f00000"

#define CONFIG_ALU				\
	"setenv bootargs root=/dev/$bdev rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"cpu 1 release 0x01000000 - - -;"		\
	"cpu 2 release 0x01000000 - - -;"		\
	"cpu 3 release 0x01000000 - - -;"		\
	"cpu 4 release 0x01000000 - - -;"		\
	"cpu 5 release 0x01000000 - - -;"		\
	"cpu 6 release 0x01000000 - - -;"		\
	"cpu 7 release 0x01000000 - - -;"		\
	"go 0x01000000"

#define CONFIG_LINUX				\
	"setenv bootargs root=/dev/ram rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"setenv ramdiskaddr 0x02000000;"		\
	"setenv fdtaddr 0x00c00000;"			\
	"setenv loadaddr 0x1000000;"			\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_HDBOOT					\
	"setenv bootargs root=/dev/$bdev rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"tftp $loadaddr $bootfile;"			\
	"tftp $fdtaddr $fdtfile;"			\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_NFSBOOTCOMMAND			\
	"setenv bootargs root=/dev/nfs rw "	\
	"nfsroot=$serverip:$rootpath "		\
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;"	\
	"tftp $loadaddr $bootfile;"		\
	"tftp $fdtaddr $fdtfile;"		\
	"bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND				\
	"setenv bootargs root=/dev/ram rw "		\
	"console=$consoledev,$baudrate $othbootargs;"	\
	"tftp $ramdiskaddr $ramdiskfile;"		\
	"tftp $loadaddr $bootfile;"			\
	"tftp $fdtaddr $fdtfile;"			\
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND		CONFIG_LINUX

#ifdef CONFIG_SECURE_BOOT
#include <asm/fsl_secure_boot.h>
#endif

#endif	/* __CONFIG_H */
Commit	Line	Data
ee52b188 YS	1	/*
	2	* Copyright 2011-2012 Freescale Semiconductor, Inc.
	3	*
1a459660	4	* SPDX-License-Identifier: GPL-2.0+
ee52b188 YS	5	*/
	6
	7	/*
	8	* T4240 QDS board configuration file
	9	*/
1cb19fbb YS	10	#ifndef __CONFIG_H
	11	#define __CONFIG_H
	12
ee52b188 YS	13	#define CONFIG_T4240QDS
ee52b188 YS	14	#define CONFIG_PHYS_64BIT
ee52b188 YS	15
	16	#define CONFIG_FSL_SATA_V2
	17	#define CONFIG_PCIE4
	18
	19	#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
	20
1cb19fbb YS	21	#ifdef CONFIG_RAMBOOT_PBL
	22	#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
	23	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	24	#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg
	25	#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg
	26	#endif
	27
	28	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
	29	/* Set 1M boot space */
	30	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
	31	#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
	32	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
	33	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	34	#define CONFIG_SYS_NO_FLASH
	35	#endif
	36
	37	#define CONFIG_SRIO_PCIE_BOOT_MASTER
	38	#define CONFIG_DDR_ECC
	39
ee52b188	40	#include "t4qds.h"
1cb19fbb YS	41
	42	#ifdef CONFIG_SYS_NO_FLASH
	43	#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
	44	#define CONFIG_ENV_IS_NOWHERE
	45	#endif
	46	#else
	47	#define CONFIG_FLASH_CFI_DRIVER
	48	#define CONFIG_SYS_FLASH_CFI
	49	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	50	#endif
	51
	52	#if defined(CONFIG_SPIFLASH)
	53	#define CONFIG_SYS_EXTRA_ENV_RELOC
	54	#define CONFIG_ENV_IS_IN_SPI_FLASH
	55	#define CONFIG_ENV_SPI_BUS 0
	56	#define CONFIG_ENV_SPI_CS 0
	57	#define CONFIG_ENV_SPI_MAX_HZ 10000000
	58	#define CONFIG_ENV_SPI_MODE 0
	59	#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
	60	#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
	61	#define CONFIG_ENV_SECT_SIZE 0x10000
	62	#elif defined(CONFIG_SDCARD)
	63	#define CONFIG_SYS_EXTRA_ENV_RELOC
	64	#define CONFIG_ENV_IS_IN_MMC
	65	#define CONFIG_SYS_MMC_ENV_DEV 0
	66	#define CONFIG_ENV_SIZE 0x2000
	67	#define CONFIG_ENV_OFFSET (512 * 1097)
	68	#elif defined(CONFIG_NAND)
	69	#define CONFIG_SYS_EXTRA_ENV_RELOC
	70	#define CONFIG_ENV_IS_IN_NAND
	71	#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
	72	#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
	73	#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
	74	#define CONFIG_ENV_IS_IN_REMOTE
	75	#define CONFIG_ENV_ADDR 0xffe20000
	76	#define CONFIG_ENV_SIZE 0x2000
	77	#elif defined(CONFIG_ENV_IS_NOWHERE)
	78	#define CONFIG_ENV_SIZE 0x2000
	79	#else
	80	#define CONFIG_ENV_IS_IN_FLASH
	81	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
	82	#define CONFIG_ENV_SIZE 0x2000
	83	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
	84	#endif
	85
	86	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
	87	#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
	88
	89	#ifndef __ASSEMBLY__
	90	unsigned long get_board_sys_clk(void);
	91	unsigned long get_board_ddr_clk(void);
	92	#endif
	93
	94	/* EEPROM */
	95	#define CONFIG_ID_EEPROM
	96	#define CONFIG_SYS_I2C_EEPROM_NXID
	97	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	98	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	99	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	100
	101	/*
	102	* DDR Setup
	103	*/
	104	#define CONFIG_SYS_SPD_BUS_NUM 0
105	#define SPD_EEPROM_ADDRESS1 0x51
106	#define SPD_EEPROM_ADDRESS2 0x52
107	#define SPD_EEPROM_ADDRESS3 0x53
108	#define SPD_EEPROM_ADDRESS4 0x54
109	#define SPD_EEPROM_ADDRESS5 0x55
110	#define SPD_EEPROM_ADDRESS6 0x56
111	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
112	#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
113
114	/*
115	* IFC Definitions
116	*/
117	#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
118	#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
119	+ 0x8000000) \| \
120	CSPR_PORT_SIZE_16 \| \
121	CSPR_MSEL_NOR \| \
122	CSPR_V)
123	#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
124	#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
125	CSPR_PORT_SIZE_16 \| \
126	CSPR_MSEL_NOR \| \
127	CSPR_V)
128	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(12810241024)
129	/* NOR Flash Timing Params */
130	#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
131
132	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
133	FTIM0_NOR_TEADC(0x5) \| \
134	FTIM0_NOR_TEAHC(0x5))
135	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
136	FTIM1_NOR_TRAD_NOR(0x1A) \|\
137	FTIM1_NOR_TSEQRAD_NOR(0x13))
138	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
139	FTIM2_NOR_TCH(0x4) \| \
140	FTIM2_NOR_TWPH(0x0E) \| \
141	FTIM2_NOR_TWP(0x1c))
142	#define CONFIG_SYS_NOR_FTIM3 0x0
143
144	#define CONFIG_SYS_FLASH_QUIET_TEST
145	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
146
147	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
148	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
149	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
150	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
151
152	#define CONFIG_SYS_FLASH_EMPTY_INFO
153	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
154	+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
155
156	#define CONFIG_FSL_QIXIS /* use common QIXIS code */
157	#define QIXIS_BASE 0xffdf0000
158	#define QIXIS_LBMAP_SWITCH 6
159	#define QIXIS_LBMAP_MASK 0x0f
160	#define QIXIS_LBMAP_SHIFT 0
161	#define QIXIS_LBMAP_DFLTBANK 0x00
162	#define QIXIS_LBMAP_ALTBANK 0x04
163	#define QIXIS_RST_CTL_RESET 0x83
c63e1370	164	#define QIXIS_RST_FORCE_MEM 0x1
1cb19fbb YS	165	#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
	166	#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
	167	#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
	168	#define QIXIS_BASE_PHYS (0xf00000000ull \| QIXIS_BASE)
	169
	170	#define CONFIG_SYS_CSPR3_EXT (0xf)
	171	#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
	172	\| CSPR_PORT_SIZE_8 \
	173	\| CSPR_MSEL_GPCM \
	174	\| CSPR_V)
	175	#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
	176	#define CONFIG_SYS_CSOR3 0x0
	177	/* QIXIS Timing parameters for IFC CS3 */
	178	#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	179	FTIM0_GPCM_TEADC(0x0e) \| \
	180	FTIM0_GPCM_TEAHC(0x0e))
	181	#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	182	FTIM1_GPCM_TRAD(0x3f))
	183	#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) \| \
	184	FTIM2_GPCM_TCH(0x0) \| \
	185	FTIM2_GPCM_TWP(0x1f))
	186	#define CONFIG_SYS_CS3_FTIM3 0x0
	187
	188	/* NAND Flash on IFC */
	189	#define CONFIG_NAND_FSL_IFC
	190	#define CONFIG_SYS_NAND_BASE 0xff800000
	191	#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull \| CONFIG_SYS_NAND_BASE)
	192
	193	#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
	194	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	195	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	196	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	197	\| CSPR_V)
	198	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
	199
	200	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	201	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	202	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	203	\| CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
	204	\| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
	205	\| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
	206	\| CSOR_NAND_PB(64)) /Pages Per Block = 64/
	207
	208	#define CONFIG_SYS_NAND_ONFI_DETECTION
	209
	210	/* ONFI NAND Flash mode0 Timing Params */
	211	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) \| \
	212	FTIM0_NAND_TWP(0x18) \| \
	213	FTIM0_NAND_TWCHT(0x07) \| \
	214	FTIM0_NAND_TWH(0x0a))
	215	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) \| \
	216	FTIM1_NAND_TWBE(0x39) \| \
	217	FTIM1_NAND_TRR(0x0e) \| \
	218	FTIM1_NAND_TRP(0x18))
	219	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) \| \
	220	FTIM2_NAND_TREH(0x0a) \| \
	221	FTIM2_NAND_TWHRE(0x1e))
	222	#define CONFIG_SYS_NAND_FTIM3 0x0
	223
	224	#define CONFIG_SYS_NAND_DDR_LAW 11
	225
	226	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	227	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	228	#define CONFIG_MTD_NAND_VERIFY_WRITE
229	#define CONFIG_CMD_NAND
230
231	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
232
233	#if defined(CONFIG_NAND)
234	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
235	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
236	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
237	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
238	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
239	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
240	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
241	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
242	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
243	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
244	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
245	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
246	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
247	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
248	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
249	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
250	#else
251	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
252	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
253	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
254	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
255	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
256	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
257	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
258	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
259	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
260	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
261	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
262	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
263	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
264	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
265	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
266	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
267	#endif
268	#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
269	#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
270	#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
271	#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
272	#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
273	#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
274	#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
275	#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
276
277	#if defined(CONFIG_RAMBOOT_PBL)
278	#define CONFIG_SYS_RAMBOOT
279	#endif
280
281
282	/* I2C */
283	#define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */
284	#define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */
285	#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
286	#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */
287
288	#define I2C_MUX_CH_DEFAULT 0x8
289	#define I2C_MUX_CH_VOL_MONITOR 0xa
290	#define I2C_MUX_CH_VSC3316_FS 0xc
291	#define I2C_MUX_CH_VSC3316_BS 0xd
292
293	/* Voltage monitor on channel 2*/
294	#define I2C_VOL_MONITOR_ADDR 0x40
295	#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
296	#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
297	#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
298
299	/* VSC Crossbar switches */
300	#define CONFIG_VSC_CROSSBAR
301	#define VSC3316_FSM_TX_ADDR 0x70
302	#define VSC3316_FSM_RX_ADDR 0x71
303
304	/*
305	* RapidIO
306	*/
307
308	/*
309	* for slave u-boot IMAGE instored in master memory space,
310	* PHYS must be aligned based on the SIZE
311	*/
312	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
313	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
314	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
315	#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
316	/*
317	* for slave UCODE and ENV instored in master memory space,
318	* PHYS must be aligned based on the SIZE
319	*/
320	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
321	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
322	#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
323
324	/* slave core release by master*/
325	#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
326	#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
327
328	/*
329	* SRIO_PCIE_BOOT - SLAVE
330	*/
331	#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
332	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
333	#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
334	(0x300000000ull \| CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
335	#endif
336	/*
337	* eSPI - Enhanced SPI
338	*/
339	#define CONFIG_FSL_ESPI
340	#define CONFIG_SPI_FLASH
341	#define CONFIG_SPI_FLASH_SST
342	#define CONFIG_CMD_SF
343	#define CONFIG_SF_DEFAULT_SPEED 10000000
344	#define CONFIG_SF_DEFAULT_MODE 0
345
346
347	/* Qman/Bman */
348	#ifndef CONFIG_NOBQFMAN
349	#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
350	#define CONFIG_SYS_BMAN_NUM_PORTALS 50
351	#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
352	#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
353	#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
354	#define CONFIG_SYS_QMAN_NUM_PORTALS 50
355	#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
356	#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
357	#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
358
359	#define CONFIG_SYS_DPAA_FMAN
360	#define CONFIG_SYS_DPAA_PME
361	#define CONFIG_SYS_PMAN
362	#define CONFIG_SYS_DPAA_DCE
363	#define CONFIG_SYS_INTERLAKEN
364
365	/* Default address of microcode for the Linux Fman driver */
366	#if defined(CONFIG_SPIFLASH)
367	/*
368	* env is stored at 0x100000, sector size is 0x10000, ucode is stored after
369	* env, so we got 0x110000.
370	*/
371	#define CONFIG_SYS_QE_FW_IN_SPIFLASH
372	#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
373	#elif defined(CONFIG_SDCARD)
374	/*
375	* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
376	* about 545KB (1089 blocks), Env is stored after the image, and the env size is
377	* 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
378	*/
379	#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
380	#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130)
381	#elif defined(CONFIG_NAND)
382	#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
383	#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
384	#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
385	/*
386	* Slave has no ucode locally, it can fetch this from remote. When implementing
387	* in two corenet boards, slave's ucode could be stored in master's memory
388	* space, the address can be mapped from slave TLB->slave LAW->
389	* slave SRIO or PCIE outbound window->master inbound window->
390	* master LAW->the ucode address in master's memory space.
391	*/
392	#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
393	#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
394	#else
395	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
396	#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
397	#endif
398	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
399	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
400	#endif /* CONFIG_NOBQFMAN */
401
402	#ifdef CONFIG_SYS_DPAA_FMAN
403	#define CONFIG_FMAN_ENET
404	#define CONFIG_PHYLIB_10G
405	#define CONFIG_PHY_VITESSE
406	#define CONFIG_PHY_TERANETICS
407	#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
408	#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
409	#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
410	#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
411	#define FM1_10GEC1_PHY_ADDR 0x0
412	#define FM1_10GEC2_PHY_ADDR 0x1
413	#define FM2_10GEC1_PHY_ADDR 0x2
414	#define FM2_10GEC2_PHY_ADDR 0x3
415	#endif
416
417
418	/* SATA */
419	#ifdef CONFIG_FSL_SATA_V2
420	#define CONFIG_LIBATA
421	#define CONFIG_FSL_SATA
422
423	#define CONFIG_SYS_SATA_MAX_DEVICE 2
424	#define CONFIG_SATA1
425	#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
426	#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
427	#define CONFIG_SATA2
428	#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
429	#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
430
431	#define CONFIG_LBA48
432	#define CONFIG_CMD_SATA
433	#define CONFIG_DOS_PARTITION
434	#define CONFIG_CMD_EXT2
435	#endif
436
437	#ifdef CONFIG_FMAN_ENET
438	#define CONFIG_MII /* MII PHY management */
439	#define CONFIG_ETHPRIME "FM1@DTSEC1"
440	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
441	#endif
442
443	/*
444	* USB
445	*/
446	#define CONFIG_CMD_USB
447	#define CONFIG_USB_STORAGE
448	#define CONFIG_USB_EHCI
449	#define CONFIG_USB_EHCI_FSL
450	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
451	#define CONFIG_CMD_EXT2
452	#define CONFIG_HAS_FSL_DR_USB
453
454	#define CONFIG_MMC
455
456	#ifdef CONFIG_MMC
457	#define CONFIG_FSL_ESDHC
458	#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
459	#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
460	#define CONFIG_CMD_MMC
461	#define CONFIG_GENERIC_MMC
462	#define CONFIG_CMD_EXT2
463	#define CONFIG_CMD_FAT
464	#define CONFIG_DOS_PARTITION
465	#endif
466
467	#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
468
469	#define __USB_PHY_TYPE utmi
470
471	/*
472	* T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
473	* 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
474	* interleaving. It can be cacheline, page, bank, superbank.
475	* See doc/README.fsl-ddr for details.
476	*/
477	#ifdef CONFIG_PPC_T4240
478	#define CTRL_INTLV_PREFERED 3way_4KB
479	#else
480	#define CTRL_INTLV_PREFERED cacheline
481	#endif
482
483	#define CONFIG_EXTRA_ENV_SETTINGS \
484	"hwconfig=fsl_ddr:" \
485	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
486	"bank_intlv=auto;" \
487	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
488	"netdev=eth0\0" \
489	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
490	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
491	"tftpflash=tftpboot $loadaddr $uboot && " \
492	"protect off $ubootaddr +$filesize && " \
493	"erase $ubootaddr +$filesize && " \
494	"cp.b $loadaddr $ubootaddr $filesize && " \
495	"protect on $ubootaddr +$filesize && " \
496	"cmp.b $loadaddr $ubootaddr $filesize\0" \
497	"consoledev=ttyS0\0" \
498	"ramdiskaddr=2000000\0" \
499	"ramdiskfile=t4240qds/ramdisk.uboot\0" \
500	"fdtaddr=c00000\0" \
501	"fdtfile=t4240qds/t4240qds.dtb\0" \
502	"bdev=sda3\0" \
503	"c=ffe\0"
504
505	#define CONFIG_HVBOOT \
506	"setenv bootargs config-addr=0x60000000; " \
507	"bootm 0x01000000 - 0x00f00000"
508
509	#define CONFIG_ALU \
510	"setenv bootargs root=/dev/$bdev rw " \
511	"console=$consoledev,$baudrate $othbootargs;" \
512	"cpu 1 release 0x01000000 - - -;" \
513	"cpu 2 release 0x01000000 - - -;" \
514	"cpu 3 release 0x01000000 - - -;" \
515	"cpu 4 release 0x01000000 - - -;" \
516	"cpu 5 release 0x01000000 - - -;" \
517	"cpu 6 release 0x01000000 - - -;" \
518	"cpu 7 release 0x01000000 - - -;" \
519	"go 0x01000000"
520
521	#define CONFIG_LINUX \
522	"setenv bootargs root=/dev/ram rw " \
523	"console=$consoledev,$baudrate $othbootargs;" \
524	"setenv ramdiskaddr 0x02000000;" \
525	"setenv fdtaddr 0x00c00000;" \
526	"setenv loadaddr 0x1000000;" \
527	"bootm $loadaddr $ramdiskaddr $fdtaddr"
528
529	#define CONFIG_HDBOOT \
530	"setenv bootargs root=/dev/$bdev rw " \
531	"console=$consoledev,$baudrate $othbootargs;" \
532	"tftp $loadaddr $bootfile;" \
533	"tftp $fdtaddr $fdtfile;" \
534	"bootm $loadaddr - $fdtaddr"
535
536	#define CONFIG_NFSBOOTCOMMAND \
537	"setenv bootargs root=/dev/nfs rw " \
538	"nfsroot=$serverip:$rootpath " \
539	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
540	"console=$consoledev,$baudrate $othbootargs;" \
541	"tftp $loadaddr $bootfile;" \
542	"tftp $fdtaddr $fdtfile;" \
543	"bootm $loadaddr - $fdtaddr"
544
545	#define CONFIG_RAMBOOTCOMMAND \
546	"setenv bootargs root=/dev/ram rw " \
547	"console=$consoledev,$baudrate $othbootargs;" \
548	"tftp $ramdiskaddr $ramdiskfile;" \
549	"tftp $loadaddr $bootfile;" \
550	"tftp $fdtaddr $fdtfile;" \
551	"bootm $loadaddr $ramdiskaddr $fdtaddr"
552
553	#define CONFIG_BOOTCOMMAND CONFIG_LINUX
554
555	#ifdef CONFIG_SECURE_BOOT
556	#include <asm/fsl_secure_boot.h>
557	#endif
558
559	#endif /* __CONFIG_H */