[people/ms/u-boot.git] / include / configs / VOM405.h

/*
 * (C) Copyright 2001-2004
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * board/config.h - configuration options, board specific
 */
#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */
#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
#define CONFIG_VOM405		1	/* ...on a VOM405 board		*/

#define	CONFIG_SYS_TEXT_BASE	0xFFFC8000

#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/

#define CONFIG_SYS_CLK_FREQ	33330000 /* external frequency to pll	*/

#define CONFIG_BAUDRATE		9600

#undef	CONFIG_BOOTARGS
#undef  CONFIG_BOOTCOMMAND

#define CONFIG_PREBOOT                  /* enable preboot variable      */

#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

#undef  CONFIG_HAS_ETH1

#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII		1	/* MII PHY management		*/
#define CONFIG_PHY_ADDR		0	/* PHY address			*/
#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME

/*
 * Command line configuration.
 */
#define CONFIG_CMD_BSP
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_EEPROM

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/

#undef  CONFIG_PRAM			/* no "protected RAM"           */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/

#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_serial_clock()

#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD	    691200

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE	\
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
	 57600, 115200, 230400, 460800, 921600 }

#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */

#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/

#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
/*
 * FLASH organization
 */
#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/

#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
/*
 * The following defines are added for buggy IOP480 byte interface.
 * All other boards should use the standard values (CPCI405 etc.)
 */
#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard			*/
#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard			*/
#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard			*/

#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN		(~(CONFIG_SYS_TEXT_BASE) + 1)
#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)

#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
# define CONFIG_SYS_RAMBOOT		1
#else
# undef CONFIG_SYS_RAMBOOT
#endif

/*
 * Environment Variable setup
 */
#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
				   /* total size of a CAT24WC16 is 2048 bytes */

#define CONFIG_SYS_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
#define CONFIG_SYS_NVRAM_SIZE		242			/* NVRAM size		*/

/*
 * I2C EEPROM (CAT24WC16) for environment
 */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_PPC4XX
#define CONFIG_SYS_I2C_PPC4XX_CH0
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F

#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
/* mask of address bits that overflow into the "EEPROM chip address"	*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
					/* 16 byte page write mode using*/
					/* last 4 bits of the address	*/
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */

/*
 * External Bus Controller (EBC) Setup
 */
#define CAN_BA		0xF0000000	    /* CAN Base Address			*/

/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
#define CONFIG_SYS_EBC_PB0AP		0x92015480
#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */

/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization		*/
#define CONFIG_SYS_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/

/*
 * FPGA stuff
 */
#define CONFIG_SYS_XSVF_DEFAULT_ADDR	0xfffc0000

/* FPGA program pin configuration */
#define CONFIG_SYS_FPGA_PRG		0x04000000  /* JTAG TMS pin (ppc output)     */
#define CONFIG_SYS_FPGA_CLK		0x02000000  /* JTAG TCK pin (ppc output)     */
#define CONFIG_SYS_FPGA_DATA		0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
#define CONFIG_SYS_FPGA_INIT		0x00010000  /* unused (ppc input)	     */
#define CONFIG_SYS_FPGA_DONE		0x00008000  /* JTAG TDI->TDO pin (ppc input) */

/*
 * Definitions for initial stack pointer and data area (in data cache)
 */
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM	  1

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/

#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Definitions for GPIO setup (PPC405EP specific)
 *
 * GPIO0[0]	- External Bus Controller BLAST output
 * GPIO0[1-9]	- Instruction trace outputs -> GPIO
 * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 * GPIO0[24-27] - UART0 control signal inputs/outputs
 * GPIO0[28-29] - UART1 data signal input/output
 * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 */
/* GPIO Input:		OSR=00, ISR=00, TSR=00, TCR=0 */
/* GPIO Output:		OSR=00, ISR=00, TSR=00, TCR=1 */
/* Alt. Funtion Input:	OSR=00, ISR=01, TSR=00, TCR=0 */
/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
#define CONFIG_SYS_GPIO0_OSRL		0x40000500  /*	0 ... 15 */
#define CONFIG_SYS_GPIO0_OSRH		0x00000110  /* 16 ... 31 */
#define CONFIG_SYS_GPIO0_ISR1L		0x00000000  /*	0 ... 15 */
#define CONFIG_SYS_GPIO0_ISR1H		0x14000045  /* 16 ... 31 */
#define CONFIG_SYS_GPIO0_TSRL		0x00000000  /*	0 ... 15 */
#define CONFIG_SYS_GPIO0_TSRH		0x00000000  /* 16 ... 31 */
#define CONFIG_SYS_GPIO0_TCR		0xF7FE0014  /*	0 ... 31 */

/*
 * Default speed selection (cpu_plb_opb_ebc) in mhz.
 * This value will be set if iic boot eprom is disabled.
 */
#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33

#endif	/* __CONFIG_H */
Commit	Line	Data
a20b27a3 SR	1	/*
	2	* (C) Copyright 2001-2004
	3	* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
	4	*
3765b3e7	5	* SPDX-License-Identifier: GPL-2.0+
a20b27a3 SR	6	*/
	7
	8	/*
	9	* board/config.h - configuration options, board specific
	10	*/
a20b27a3 SR	11	#ifndef __CONFIG_H
	12	#define __CONFIG_H
	13
	14	/*
	15	* High Level Configuration Options
	16	* (easy to change)
	17	*/
a20b27a3	18	#define CONFIG_405EP 1 /* This is a PPC405 CPU */
a20b27a3 SR	19	#define CONFIG_VOM405 1 /* ...on a VOM405 board */
a20b27a3 SR	20
2ae18241 WD	21	#define CONFIG_SYS_TEXT_BASE 0xFFFC8000
2ae18241 WD	22
a20b27a3 SR	23	#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
	24
	25	#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
	26
	27	#define CONFIG_BAUDRATE 9600
a20b27a3 SR	28
	29	#undef CONFIG_BOOTARGS
	30	#undef CONFIG_BOOTCOMMAND
	31
	32	#define CONFIG_PREBOOT /* enable preboot variable */
	33
6d0f6bcf	34	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
a20b27a3	35
feaedfcf SR	36	#undef CONFIG_HAS_ETH1
feaedfcf SR	37
96e21f86	38	#define CONFIG_PPC4xx_EMAC
a20b27a3 SR	39	#define CONFIG_MII 1 /* MII PHY management */
	40	#define CONFIG_PHY_ADDR 0 /* PHY address */
	41	#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
feaedfcf	42	#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
a20b27a3	43
37d4bb70 JL	44	/*
	45	* BOOTP options
	46	*/
	47	#define CONFIG_BOOTP_SUBNETMASK
	48	#define CONFIG_BOOTP_GATEWAY
	49	#define CONFIG_BOOTP_HOSTNAME
	50	#define CONFIG_BOOTP_BOOTPATH
	51	#define CONFIG_BOOTP_DNS
	52	#define CONFIG_BOOTP_DNS2
	53	#define CONFIG_BOOTP_SEND_HOSTNAME
a20b27a3	54
a5562901 JL	55	/*
	56	* Command line configuration.
	57	*/
a5562901	58	#define CONFIG_CMD_BSP
a5562901	59	#define CONFIG_CMD_IRQ
a5562901 JL	60	#define CONFIG_CMD_EEPROM
a5562901 JL	61
a20b27a3 SR	62	#undef CONFIG_WATCHDOG /* watchdog disabled */
	63
	64	#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
	65
	66	#undef CONFIG_PRAM /* no "protected RAM" */
	67
	68	/*
	69	* Miscellaneous configurable options
	70	*/
6d0f6bcf	71	#define CONFIG_SYS_LONGHELP /* undef to save memory */
a20b27a3	72
a5562901	73	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	74	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
a20b27a3	75	#else
6d0f6bcf	76	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
a20b27a3	77	#endif
6d0f6bcf JCPV	78	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	79	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	80	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
a20b27a3	81
6d0f6bcf	82	#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
a20b27a3	83
6d0f6bcf JCPV	84	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
6d0f6bcf JCPV	85	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
a20b27a3	86
550650dd	87	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
550650dd SR	88	#define CONFIG_SYS_NS16550_SERIAL
	89	#define CONFIG_SYS_NS16550_REG_SIZE 1
	90	#define CONFIG_SYS_NS16550_CLK get_serial_clock()
	91
6d0f6bcf	92	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
6d0f6bcf	93	#define CONFIG_SYS_BASE_BAUD 691200
a20b27a3 SR	94
a20b27a3 SR	95	/* The following table includes the supported baudrates */
6d0f6bcf	96	#define CONFIG_SYS_BAUDRATE_TABLE \
a20b27a3 SR	97	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
	98	57600, 115200, 230400, 460800, 921600 }
	99
6d0f6bcf JCPV	100	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6d0f6bcf JCPV	101	#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
a20b27a3	102
1092ce21	103	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
a20b27a3	104
6d0f6bcf	105	#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
a20b27a3	106
a20b27a3 SR	107	/*
	108	* For booting Linux, the board info and command line data
	109	* have to be in the first 8 MB of memory, since this is
	110	* the maximum mapped by the Linux kernel during initialization.
	111	*/
6d0f6bcf	112	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
1092ce21	113	/*
a20b27a3 SR	114	* FLASH organization
	115	*/
	116	#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
	117
6d0f6bcf JCPV	118	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
6d0f6bcf JCPV	119	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
a20b27a3	120
6d0f6bcf JCPV	121	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	122	#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
a20b27a3	123
6d0f6bcf JCPV	124	#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
	125	#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
	126	#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
a20b27a3 SR	127	/*
	128	* The following defines are added for buggy IOP480 byte interface.
	129	* All other boards should use the standard values (CPCI405 etc.)
	130	*/
6d0f6bcf JCPV	131	#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
	132	#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
	133	#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
a20b27a3	134
6d0f6bcf	135	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
a20b27a3	136
1092ce21	137	/*
a20b27a3 SR	138	* Start addresses for the final memory configuration
a20b27a3 SR	139	* (Set up by the startup code)
6d0f6bcf	140	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
a20b27a3	141	*/
6d0f6bcf	142	#define CONFIG_SYS_SDRAM_BASE 0x00000000
700d553f	143	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE
14d0a02a WD	144	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
14d0a02a WD	145	#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
700d553f	146	#define CONFIG_SYS_MALLOC_LEN (256 * 1024)
6d0f6bcf JCPV	147
	148	#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
	149	# define CONFIG_SYS_RAMBOOT 1
a20b27a3	150	#else
6d0f6bcf	151	# undef CONFIG_SYS_RAMBOOT
a20b27a3 SR	152	#endif
a20b27a3 SR	153
1092ce21	154	/*
a20b27a3 SR	155	* Environment Variable setup
a20b27a3 SR	156	*/
bb1f8b4f	157	#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
0e8d1586 JCPV	158	#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
0e8d1586 JCPV	159	#define CONFIG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
a20b27a3 SR	160	/* total size of a CAT24WC16 is 2048 bytes */
a20b27a3 SR	161
6d0f6bcf JCPV	162	#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
6d0f6bcf JCPV	163	#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
a20b27a3	164
1092ce21	165	/*
a20b27a3 SR	166	* I2C EEPROM (CAT24WC16) for environment
a20b27a3 SR	167	*/
880540de DE	168	#define CONFIG_SYS_I2C
	169	#define CONFIG_SYS_I2C_PPC4XX
	170	#define CONFIG_SYS_I2C_PPC4XX_CH0
	171	#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
	172	#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
a20b27a3	173
6d0f6bcf JCPV	174	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
6d0f6bcf JCPV	175	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
a20b27a3	176	/* mask of address bits that overflow into the "EEPROM chip address" */
6d0f6bcf JCPV	177	#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
6d0f6bcf JCPV	178	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
a20b27a3 SR	179	/* 16 byte page write mode using*/
a20b27a3 SR	180	/* last 4 bits of the address */
6d0f6bcf	181	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
a20b27a3	182
1092ce21	183	/*
a20b27a3 SR	184	* External Bus Controller (EBC) Setup
a20b27a3 SR	185	*/
a20b27a3 SR	186	#define CAN_BA 0xF0000000 /* CAN Base Address */
	187
	188	/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
6d0f6bcf JCPV	189	#define CONFIG_SYS_EBC_PB0AP 0x92015480
6d0f6bcf JCPV	190	#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
a20b27a3 SR	191
a20b27a3 SR	192	/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
6d0f6bcf JCPV	193	#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
6d0f6bcf JCPV	194	#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
a20b27a3	195
1092ce21	196	/*
a20b27a3 SR	197	* FPGA stuff
a20b27a3 SR	198	*/
700d553f	199	#define CONFIG_SYS_XSVF_DEFAULT_ADDR 0xfffc0000
a20b27a3 SR	200
a20b27a3 SR	201	/* FPGA program pin configuration */
6d0f6bcf JCPV	202	#define CONFIG_SYS_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
	203	#define CONFIG_SYS_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
	204	#define CONFIG_SYS_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
	205	#define CONFIG_SYS_FPGA_INIT 0x00010000 /* unused (ppc input) */
	206	#define CONFIG_SYS_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
a20b27a3	207
1092ce21	208	/*
a20b27a3 SR	209	* Definitions for initial stack pointer and data area (in data cache)
	210	*/
	211	/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
6d0f6bcf	212	#define CONFIG_SYS_TEMP_STACK_OCM 1
a20b27a3 SR	213
a20b27a3 SR	214	/* On Chip Memory location */
6d0f6bcf JCPV	215	#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
	216	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
	217	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
553f0982	218	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
a20b27a3	219
25ddd1fb	220	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	221	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
a20b27a3	222
1092ce21	223	/*
a20b27a3 SR	224	* Definitions for GPIO setup (PPC405EP specific)
	225	*
	226	* GPIO0[0] - External Bus Controller BLAST output
	227	* GPIO0[1-9] - Instruction trace outputs -> GPIO
	228	* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
	229	* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
	230	* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
	231	* GPIO0[24-27] - UART0 control signal inputs/outputs
	232	* GPIO0[28-29] - UART1 data signal input/output
	233	* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
	234	*/
	235	/* GPIO Input: OSR=00, ISR=00, TSR=00, TCR=0 */
	236	/* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */
	237	/* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */
	238	/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
afabb498 SR	239	#define CONFIG_SYS_GPIO0_OSRL 0x40000500 /* 0 ... 15 */
	240	#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* 16 ... 31 */
	241	#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 /* 0 ... 15 */
	242	#define CONFIG_SYS_GPIO0_ISR1H 0x14000045 /* 16 ... 31 */
	243	#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 0 ... 15 */
	244	#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 16 ... 31 */
6d0f6bcf	245	#define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */
a20b27a3	246
a20b27a3 SR	247	/*
	248	* Default speed selection (cpu_plb_opb_ebc) in mhz.
	249	* This value will be set if iic boot eprom is disabled.
	250	*/
a20b27a3 SR	251	#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
a20b27a3 SR	252	#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
a20b27a3 SR	253
a20b27a3 SR	254	#endif /* __CONFIG_H */