[people/ms/u-boot.git] / include / configs / astro_mcf5373l.h

/*
 * Configuration settings for the Sentec Cobra Board.
 *
 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * configuration for ASTRO "Urmel" board.
 * Originating from Cobra5272 configuration, messed up by
 * Wolfgang Wegner <w.wegner@astro-kom.de>
 * Please do not bother the original author with bug reports
 * concerning this file.
 */

#ifndef _CONFIG_ASTRO_MCF5373L_H
#define _CONFIG_ASTRO_MCF5373L_H

#include <linux/stringify.h>

/*
 * set the card type to actually compile for; either of
 * the possibilities listed below has to be used!
 */
#define CONFIG_ASTRO_V532	1

#if CONFIG_ASTRO_V532
#define ASTRO_ID	0xF8
#elif CONFIG_ASTRO_V512
#define ASTRO_ID	0xFA
#elif CONFIG_ASTRO_TWIN7S2
#define ASTRO_ID	0xF9
#elif CONFIG_ASTRO_V912
#define ASTRO_ID	0xFC
#elif CONFIG_ASTRO_COFDMDUOS2
#define ASTRO_ID	0xFB
#else
#error No card type defined!
#endif

#define CONFIG_ASTRO5373L		/* define board type */

/* Command line configuration */
/*
 * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
 * a different bootloader that has already performed RAM setup) or
 * started directly from flash, which is the regular case for production
 * boards.
 */
#ifdef CONFIG_RAM
#define CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_SYS_TEXT_BASE		0x40020000
#define ENABLE_JFFS	0
#else
#define CONFIG_SYS_TEXT_BASE		0x00000000
#define ENABLE_JFFS	1
#endif

/* Define which commands should be available at u-boot command prompt */

#define CONFIG_CMD_REGINFO
#define CONFIG_CMDLINE_EDITING

#define CONFIG_MCFRTC
#undef RTC_DEBUG

/* Timer */
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	80000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x58000
#define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR

/*
 * Defines processor clock - important for correct timings concerning serial
 * interface etc.
 */

#define CONFIG_SYS_CLK			80000000
#define CONFIG_SYS_CPU_CLK		(CONFIG_SYS_CLK * 3)
#define CONFIG_SYS_SDRAM_SIZE		32		/* SDRAM size in MB */

#define CONFIG_SYS_CORE_SRAM_SIZE	0x8000
#define CONFIG_SYS_CORE_SRAM		0x80000000

#define CONFIG_SYS_UNIFY_CACHE

/*
 * Define baudrate for UART1 (console output, tftp, ...)
 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
 * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected
 * in u-boot command interface
 */

#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT		(2)
#define CONFIG_SYS_UART2_ALT3_GPIO

/*
 * Watchdog configuration; Watchdog is disabled for running from RAM
 * and set to highest possible value else. Beware there is no check
 * in the watchdog code to validate the timeout value set here!
 */

#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT 3355	/* timeout in milliseconds */
#endif

/*
 * Configuration for environment
 * Environment is located in the last sector of the flash
 */

#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_ENV_OFFSET		0x1FF8000
#define CONFIG_ENV_SECT_SIZE		0x8000
#define CONFIG_ENV_IS_IN_FLASH		1
#else
/*
 * environment in RAM - This is used to use a single PC-based application
 * to load an image, load U-Boot, load an environment and then start U-Boot
 * to execute the commands from the environment. Feedback is done via setting
 * and reading memory locations.
 */
#define CONFIG_ENV_ADDR		0x40060000
#define CONFIG_ENV_SECT_SIZE	0x8000
#define CONFIG_ENV_IS_IN_FLASH	1
#endif

/* here we put our FPGA configuration... */
#define CONFIG_MISC_INIT_R	1

/* Define user parameters that have to be customized most likely */

/* AUTOBOOT settings - booting images automatically by u-boot after power on */

/*
 * The following settings will be contained in the environment block ; if you
 * want to use a neutral environment all those settings can be manually set in
 * u-boot: 'set' command
 */

#define CONFIG_EXTRA_ENV_SETTINGS			\
	"loaderversion=11\0"				\
	"card_id="__stringify(ASTRO_ID)"\0"			\
	"alterafile=0\0"				\
	"xilinxfile=0\0"				\
	"xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\
		"fpga load 0 0x41000000 $filesize\0" \
	"alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\
		"fpga load 1 0x41000000 $filesize\0" \
	"env_default=1\0"				\
	"env_check=if test $env_default -eq 1;"\
		" then setenv env_default 0;saveenv;fi\0"

/*
 * "update" is a non-standard command that has to be supplied
 * by external update.c; This is not included in mainline because
 * it needs non-blocking CFI routines.
 */
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_BOOTCOMMAND	""	/* no autoboot in this case */
#else
#if CONFIG_ASTRO_V532
#define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
				"run xilinxload&&run alteraload&&bootm 0x80000;"\
				"update;reset"
#else
#define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
				"run xilinxload&&bootm 0x80000;update;reset"
#endif
#endif

/* default bootargs that are considered during boot */
#define CONFIG_BOOTARGS		" console=ttyS2,115200 rootfstype=romfs"\
				" loaderversion=$loaderversion"

/* default RAM address for user programs */
#define CONFIG_SYS_LOAD_ADDR	0x20000

#define CONFIG_SYS_LONGHELP

#if (CONFIG_COMMANDS & CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE		1024
#else
#define CONFIG_SYS_CBSIZE		256
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS		16
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

#define CONFIG_FPGA_COUNT	1
#define CONFIG_FPGA
#define	CONFIG_FPGA_XILINX
#define	CONFIG_FPGA_SPARTAN3
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_CYCLON2
#define CONFIG_SYS_FPGA_PROG_FEEDBACK
#define CONFIG_SYS_FPGA_WAIT		1000

/* End of user parameters to be customized */

/* Defines memory range for test */

#define CONFIG_SYS_MEMTEST_START	0x40020000
#define CONFIG_SYS_MEMTEST_END		0x41ffffff

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */

/* Base register address */

#define CONFIG_SYS_MBAR		0xFC000000	/* Register Base Addrs */

/* System Conf. Reg. & System Protection Reg. */

#define CONFIG_SYS_SCR		0x0003;
#define CONFIG_SYS_SPR		0xffff;

/*
 * Definitions for initial stack pointer and data area (in internal SRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR	0x80000000
#define CONFIG_SYS_INIT_RAM_SIZE		0x8000
#define CONFIG_SYS_INIT_RAM_CTRL	0x221
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
					 GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000
 */
#define CONFIG_SYS_SDRAM_BASE		0x40000000

/*
 * Chipselect bank definitions
 *
 * CS0 - Flash 32MB (first 16MB)
 * CS1 - Flash 32MB (second half)
 * CS2 - FPGA
 * CS3 - FPGA
 * CS4 - unused
 * CS5 - unused
 */
#define CONFIG_SYS_CS0_BASE		0
#define CONFIG_SYS_CS0_MASK		0x00ff0001
#define CONFIG_SYS_CS0_CTRL		0x00001fc0

#define CONFIG_SYS_CS1_BASE		0x01000000
#define CONFIG_SYS_CS1_MASK		0x00ff0001
#define CONFIG_SYS_CS1_CTRL		0x00001fc0

#define CONFIG_SYS_CS2_BASE		0x20000000
#define CONFIG_SYS_CS2_MASK		0x00ff0001
#define CONFIG_SYS_CS2_CTRL		0x0000fec0

#define CONFIG_SYS_CS3_BASE		0x21000000
#define CONFIG_SYS_CS3_MASK		0x00ff0001
#define CONFIG_SYS_CS3_CTRL		0x0000fec0

#define CONFIG_SYS_FLASH_BASE		0x00000000

#ifdef	CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
#else
/* This is mainly used during relocation in start.S */
#define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_FLASH_BASE + 0x400)
#endif
/* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MONITOR_LEN		(256 << 10)

#define CONFIG_SYS_BOOTPARAMS_LEN	(64 * 1024)
/* Reserve 128 kB for malloc() */
#define CONFIG_SYS_MALLOC_LEN		(128 << 10)

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization ??
 */
#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + \
						(CONFIG_SYS_SDRAM_SIZE << 20))

/* FLASH organization */
#define CONFIG_SYS_MAX_FLASH_BANKS	1
#define CONFIG_SYS_MAX_FLASH_SECT	259
#define CONFIG_SYS_FLASH_ERASE_TOUT	1000

#define CONFIG_SYS_FLASH_CFI		1
#define CONFIG_FLASH_CFI_DRIVER		1
#define CONFIG_SYS_FLASH_SIZE		0x2000000
#define CONFIG_SYS_FLASH_PROTECTION	1
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
#define CONFIG_SYS_FLASH_CFI_NONBLOCK	1

#define LDS_BOARD_TEXT \
	. = DEFINED(env_offset) ? env_offset : .; \
	common/env_embedded.o       (.text*)

#if ENABLE_JFFS
/* JFFS Partition offset set */
#define CONFIG_SYS_JFFS2_FIRST_BANK    0
#define CONFIG_SYS_JFFS2_NUM_BANKS     1
/* 512k reserved for u-boot */
#define CONFIG_SYS_JFFS2_FIRST_SECTOR  0x40
#endif

/* Cache Configuration */
#define CONFIG_SYS_CACHELINE_SIZE	16

#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINVA)
#define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_SDRAM_BASE | \
					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
					 CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_EC | CF_CACR_CINVA | \
					 CF_CACR_DCM_P)

#endif	/* _CONFIG_ASTRO_MCF5373L_H */
Commit	Line	Data
9d79e575 WW	1	/*
	2	* Configuration settings for the Sentec Cobra Board.
	3	*
	4	* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
	5	*
3765b3e7	6	* SPDX-License-Identifier: GPL-2.0+
9d79e575 WW	7	*/
	8
	9	/*
	10	* configuration for ASTRO "Urmel" board.
	11	* Originating from Cobra5272 configuration, messed up by
	12	* Wolfgang Wegner <w.wegner@astro-kom.de>
	13	* Please do not bother the original author with bug reports
	14	* concerning this file.
	15	*/
	16
	17	#ifndef _CONFIG_ASTRO_MCF5373L_H
	18	#define _CONFIG_ASTRO_MCF5373L_H
	19
51926d5e MV	20	#include <linux/stringify.h>
51926d5e MV	21
9d79e575 WW	22	/*
	23	* set the card type to actually compile for; either of
	24	* the possibilities listed below has to be used!
	25	*/
	26	#define CONFIG_ASTRO_V532 1
	27
	28	#if CONFIG_ASTRO_V532
	29	#define ASTRO_ID 0xF8
	30	#elif CONFIG_ASTRO_V512
	31	#define ASTRO_ID 0xFA
	32	#elif CONFIG_ASTRO_TWIN7S2
	33	#define ASTRO_ID 0xF9
	34	#elif CONFIG_ASTRO_V912
	35	#define ASTRO_ID 0xFC
	36	#elif CONFIG_ASTRO_COFDMDUOS2
	37	#define ASTRO_ID 0xFB
	38	#else
	39	#error No card type defined!
	40	#endif
	41
9d79e575 WW	42	#define CONFIG_ASTRO5373L /* define board type */
	43
	44	/* Command line configuration */
9d79e575	45	/*
d24f2d32	46	* CONFIG_RAM defines if u-boot is loaded via BDM (or started from
9d79e575 WW	47	* a different bootloader that has already performed RAM setup) or
	48	* started directly from flash, which is the regular case for production
	49	* boards.
	50	*/
d24f2d32	51	#ifdef CONFIG_RAM
9d79e575	52	#define CONFIG_MONITOR_IS_IN_RAM
14d0a02a	53	#define CONFIG_SYS_TEXT_BASE 0x40020000
9d79e575 WW	54	#define ENABLE_JFFS 0
9d79e575 WW	55	#else
14d0a02a	56	#define CONFIG_SYS_TEXT_BASE 0x00000000
9d79e575 WW	57	#define ENABLE_JFFS 1
	58	#endif
	59
3f42dc87	60	/* Define which commands should be available at u-boot command prompt */
9d79e575	61
9d79e575	62	#define CONFIG_CMD_REGINFO
9d79e575 WW	63	#define CONFIG_CMDLINE_EDITING
9d79e575 WW	64
9d79e575 WW	65	#define CONFIG_MCFRTC
	66	#undef RTC_DEBUG
	67
	68	/* Timer */
	69	#define CONFIG_MCFTMR
	70	#undef CONFIG_MCFPIT
	71
	72	/* I2C */
00f792e0 HS	73	#define CONFIG_SYS_I2C
	74	#define CONFIG_SYS_I2C_FSL
	75	#define CONFIG_SYS_FSL_I2C_SPEED 80000
	76	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	77	#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
9d79e575 WW	78	#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
	79
	80	/*
	81	* Defines processor clock - important for correct timings concerning serial
	82	* interface etc.
9d79e575 WW	83	*/
9d79e575 WW	84
9d79e575 WW	85	#define CONFIG_SYS_CLK 80000000
	86	#define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3)
	87	#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
	88
	89	#define CONFIG_SYS_CORE_SRAM_SIZE 0x8000
	90	#define CONFIG_SYS_CORE_SRAM 0x80000000
	91
	92	#define CONFIG_SYS_UNIFY_CACHE
	93
	94	/*
	95	* Define baudrate for UART1 (console output, tftp, ...)
	96	* default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
	97	* CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected
	98	* in u-boot command interface
	99	*/
	100
9d79e575 WW	101	#define CONFIG_MCFUART
	102	#define CONFIG_SYS_UART_PORT (2)
	103	#define CONFIG_SYS_UART2_ALT3_GPIO
	104
	105	/*
	106	* Watchdog configuration; Watchdog is disabled for running from RAM
	107	* and set to highest possible value else. Beware there is no check
	108	* in the watchdog code to validate the timeout value set here!
	109	*/
	110
	111	#ifndef CONFIG_MONITOR_IS_IN_RAM
	112	#define CONFIG_WATCHDOG
	113	#define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */
	114	#endif
	115
	116	/*
	117	* Configuration for environment
	118	* Environment is located in the last sector of the flash
	119	*/
	120
	121	#ifndef CONFIG_MONITOR_IS_IN_RAM
	122	#define CONFIG_ENV_OFFSET 0x1FF8000
	123	#define CONFIG_ENV_SECT_SIZE 0x8000
	124	#define CONFIG_ENV_IS_IN_FLASH 1
	125	#else
	126	/*
	127	* environment in RAM - This is used to use a single PC-based application
	128	* to load an image, load U-Boot, load an environment and then start U-Boot
	129	* to execute the commands from the environment. Feedback is done via setting
	130	* and reading memory locations.
	131	*/
	132	#define CONFIG_ENV_ADDR 0x40060000
	133	#define CONFIG_ENV_SECT_SIZE 0x8000
	134	#define CONFIG_ENV_IS_IN_FLASH 1
	135	#endif
	136
	137	/* here we put our FPGA configuration... */
	138	#define CONFIG_MISC_INIT_R 1
	139
	140	/* Define user parameters that have to be customized most likely */
	141
	142	/* AUTOBOOT settings - booting images automatically by u-boot after power on */
	143
9d79e575 WW	144	/*
	145	* The following settings will be contained in the environment block ; if you
	146	* want to use a neutral environment all those settings can be manually set in
	147	* u-boot: 'set' command
	148	*/
	149
9d79e575 WW	150	#define CONFIG_EXTRA_ENV_SETTINGS \
9d79e575 WW	151	"loaderversion=11\0" \
51926d5e	152	"card_id="__stringify(ASTRO_ID)"\0" \
9d79e575 WW	153	"alterafile=0\0" \
	154	"xilinxfile=0\0" \
	155	"xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\
	156	"fpga load 0 0x41000000 $filesize\0" \
	157	"alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\
	158	"fpga load 1 0x41000000 $filesize\0" \
	159	"env_default=1\0" \
	160	"env_check=if test $env_default -eq 1;"\
	161	" then setenv env_default 0;saveenv;fi\0"
	162
	163	/*
	164	* "update" is a non-standard command that has to be supplied
	165	* by external update.c; This is not included in mainline because
	166	* it needs non-blocking CFI routines.
	167	*/
	168	#ifdef CONFIG_MONITOR_IS_IN_RAM
	169	#define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */
	170	#else
	171	#if CONFIG_ASTRO_V532
	172	#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\
	173	"run xilinxload&&run alteraload&&bootm 0x80000;"\
	174	"update;reset"
	175	#else
	176	#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\
	177	"run xilinxload&&bootm 0x80000;update;reset"
	178	#endif
	179	#endif
	180
	181	/* default bootargs that are considered during boot */
	182	#define CONFIG_BOOTARGS " console=ttyS2,115200 rootfstype=romfs"\
	183	" loaderversion=$loaderversion"
	184
9d79e575 WW	185	/* default RAM address for user programs */
	186	#define CONFIG_SYS_LOAD_ADDR 0x20000
	187
	188	#define CONFIG_SYS_LONGHELP
	189
	190	#if (CONFIG_COMMANDS & CONFIG_CMD_KGDB)
	191	#define CONFIG_SYS_CBSIZE 1024
	192	#else
	193	#define CONFIG_SYS_CBSIZE 256
	194	#endif
	195	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
	196	#define CONFIG_SYS_MAXARGS 16
	197	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	198
	199	#define CONFIG_FPGA_COUNT 1
	200	#define CONFIG_FPGA
	201	#define CONFIG_FPGA_XILINX
	202	#define CONFIG_FPGA_SPARTAN3
	203	#define CONFIG_FPGA_ALTERA
	204	#define CONFIG_FPGA_CYCLON2
	205	#define CONFIG_SYS_FPGA_PROG_FEEDBACK
	206	#define CONFIG_SYS_FPGA_WAIT 1000
	207
	208	/* End of user parameters to be customized */
	209
	210	/* Defines memory range for test */
	211
	212	#define CONFIG_SYS_MEMTEST_START 0x40020000
	213	#define CONFIG_SYS_MEMTEST_END 0x41ffffff
	214
	215	/*
	216	* Low Level Configuration Settings
	217	* (address mappings, register initial values, etc.)
	218	* You should know what you are doing if you make changes here.
	219	*/
	220
	221	/* Base register address */
	222
	223	#define CONFIG_SYS_MBAR 0xFC000000 /* Register Base Addrs */
	224
	225	/* System Conf. Reg. & System Protection Reg. */
	226
	227	#define CONFIG_SYS_SCR 0x0003;
	228	#define CONFIG_SYS_SPR 0xffff;
	229
	230	/*
	231	* Definitions for initial stack pointer and data area (in internal SRAM)
	232	*/
	233	#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
553f0982	234	#define CONFIG_SYS_INIT_RAM_SIZE 0x8000
9d79e575	235	#define CONFIG_SYS_INIT_RAM_CTRL 0x221
553f0982	236	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
25ddd1fb	237	GENERATED_GBL_DATA_SIZE)
9d79e575 WW	238	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	239
	240	/*
	241	* Start addresses for the final memory configuration
	242	* (Set up by the startup code)
	243	* for MCF5373, the allowable range is 0x40000000 to 0x7FF00000
	244	*/
	245	#define CONFIG_SYS_SDRAM_BASE 0x40000000
	246
	247	/*
	248	* Chipselect bank definitions
	249	*
	250	* CS0 - Flash 32MB (first 16MB)
	251	* CS1 - Flash 32MB (second half)
	252	* CS2 - FPGA
	253	* CS3 - FPGA
	254	* CS4 - unused
	255	* CS5 - unused
	256	*/
	257	#define CONFIG_SYS_CS0_BASE 0
	258	#define CONFIG_SYS_CS0_MASK 0x00ff0001
	259	#define CONFIG_SYS_CS0_CTRL 0x00001fc0
	260
	261	#define CONFIG_SYS_CS1_BASE 0x01000000
	262	#define CONFIG_SYS_CS1_MASK 0x00ff0001
	263	#define CONFIG_SYS_CS1_CTRL 0x00001fc0
	264
	265	#define CONFIG_SYS_CS2_BASE 0x20000000
	266	#define CONFIG_SYS_CS2_MASK 0x00ff0001
	267	#define CONFIG_SYS_CS2_CTRL 0x0000fec0
	268
	269	#define CONFIG_SYS_CS3_BASE 0x21000000
	270	#define CONFIG_SYS_CS3_MASK 0x00ff0001
	271	#define CONFIG_SYS_CS3_CTRL 0x0000fec0
	272
	273	#define CONFIG_SYS_FLASH_BASE 0x00000000
	274
	275	#ifdef CONFIG_MONITOR_IS_IN_RAM
14d0a02a	276	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
9d79e575 WW	277	#else
	278	/* This is mainly used during relocation in start.S */
	279	#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
	280	#endif
	281	/* Reserve 256 kB for Monitor */
	282	#define CONFIG_SYS_MONITOR_LEN (256 << 10)
	283
	284	#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024)
	285	/* Reserve 128 kB for malloc() */
	286	#define CONFIG_SYS_MALLOC_LEN (128 << 10)
	287
	288	/*
	289	* For booting Linux, the board info and command line data
	290	* have to be in the first 8 MB of memory, since this is
	291	* the maximum mapped by the Linux kernel during initialization ??
	292	*/
	293	#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \
	294	(CONFIG_SYS_SDRAM_SIZE << 20))
	295
	296	/* FLASH organization */
	297	#define CONFIG_SYS_MAX_FLASH_BANKS 1
	298	#define CONFIG_SYS_MAX_FLASH_SECT 259
	299	#define CONFIG_SYS_FLASH_ERASE_TOUT 1000
	300
	301	#define CONFIG_SYS_FLASH_CFI 1
	302	#define CONFIG_FLASH_CFI_DRIVER 1
	303	#define CONFIG_SYS_FLASH_SIZE 0x2000000
	304	#define CONFIG_SYS_FLASH_PROTECTION 1
	305	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
	306	#define CONFIG_SYS_FLASH_CFI_NONBLOCK 1
	307
5296cb1d	308	#define LDS_BOARD_TEXT \
	309	. = DEFINED(env_offset) ? env_offset : .; \
	310	common/env_embedded.o (.text*)
	311
9d79e575 WW	312	#if ENABLE_JFFS
	313	/* JFFS Partition offset set */
	314	#define CONFIG_SYS_JFFS2_FIRST_BANK 0
	315	#define CONFIG_SYS_JFFS2_NUM_BANKS 1
	316	/* 512k reserved for u-boot */
	317	#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0x40
	318	#endif
	319
	320	/* Cache Configuration */
	321	#define CONFIG_SYS_CACHELINE_SIZE 16
	322
dd9f054e	323	#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	324	CONFIG_SYS_INIT_RAM_SIZE - 8)
dd9f054e	325	#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	326	CONFIG_SYS_INIT_RAM_SIZE - 4)
dd9f054e TL	327	#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA)
	328	#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE \| \
	329	CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) \| \
	330	CF_ACR_EN \| CF_ACR_SM_ALL)
	331	#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC \| CF_CACR_CINVA \| \
	332	CF_CACR_DCM_P)
	333
9d79e575	334	#endif /* _CONFIG_ASTRO_MCF5373L_H */