[people/ms/u-boot.git] / include / configs / bcm23550_w1d.h

/*
 * Copyright 2013 Broadcom Corporation.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __BCM23550_W1D_H
#define __BCM23550_W1D_H

#include <linux/sizes.h>
#include <asm/arch/sysmap.h>

/* CPU, chip, mach, etc */
#define CONFIG_KONA
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_KONA_RESET_S

/*
 * Memory configuration
 */
#define CONFIG_SYS_TEXT_BASE		0x9f000000

#define CONFIG_SYS_SDRAM_BASE		0x80000000
#define CONFIG_SYS_SDRAM_SIZE		0x20000000
#define CONFIG_NR_DRAM_BANKS		1

#define CONFIG_SYS_MALLOC_LEN		SZ_4M	/* see armv7/start.S. */
#define CONFIG_STACKSIZE		SZ_256K

/* GPIO Driver */
#define CONFIG_KONA_GPIO

/* MMC/SD Driver */
#define CONFIG_SDHCI
#define CONFIG_MMC_SDMA
#define CONFIG_KONA_SDHCI
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC

#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
#define CONFIG_SYS_SDIO0_MAX_CLK 48000000
#define CONFIG_SYS_SDIO1_MAX_CLK 48000000
#define CONFIG_SYS_SDIO2_MAX_CLK 48000000
#define CONFIG_SYS_SDIO3_MAX_CLK 48000000
#define CONFIG_SYS_SDIO0 "sdio1"
#define CONFIG_SYS_SDIO1 "sdio2"
#define CONFIG_SYS_SDIO2 "sdio3"
#define CONFIG_SYS_SDIO3 "sdio4"

/* I2C Driver */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_KONA
#define CONFIG_SYS_SPD_BUS_NUM	3	/* Start with PMU bus */
#define CONFIG_SYS_MAX_I2C_BUS	4
#define CONFIG_SYS_I2C_BASE0	BSC1_BASE_ADDR
#define CONFIG_SYS_I2C_BASE1	BSC2_BASE_ADDR
#define CONFIG_SYS_I2C_BASE2	BSC3_BASE_ADDR
#define CONFIG_SYS_I2C_BASE3	PMU_BSC_BASE_ADDR

/* Timer Driver */
#define CONFIG_SYS_TIMER_RATE		32000
#define CONFIG_SYS_TIMER_COUNTER	(TIMER_BASE_ADDR + 4) /* STCLO offset */

/* Init functions */
#define CONFIG_MISC_INIT_R	/* board's misc_init_r function */

/* Some commands use this as the default load address */
#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE

/* No mtest functions as recommended */

/*
 * This is the initial SP which is used only briefly for relocating the u-boot
 * image to the top of SDRAM. After relocation u-boot moves the stack to the
 * proper place.
 */
#define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE

/* Serial Info */
#define CONFIG_SYS_NS16550_SERIAL
/* Post pad 3 bytes after each reg addr */
#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
#define CONFIG_SYS_NS16550_CLK		13000000
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550_COM1		0x3e000000

#define CONFIG_BAUDRATE			115200

/* must fit into GPT:u-boot-env partition */
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV		0
#define CONFIG_ENV_OFFSET		(0x00011a00 * 512)
#define CONFIG_ENV_SIZE			(8 * 512)

#define CONFIG_SYS_NO_FLASH	/* Not using NAND/NOR unmanaged flash */

/* console configuration */
#define CONFIG_SYS_CBSIZE		1024	/* Console buffer size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
			sizeof(CONFIG_SYS_PROMPT) + 16)	/* Printbuffer size */
#define CONFIG_SYS_MAXARGS		64
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

/*
 * One partition type must be defined for part.c
 * This is necessary for the fatls command to work on an SD card
 * for example.
 */
#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION

/* version string, parser, etc */
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP

#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC

/* Initial upstream - boot to cmd prompt only */
#define CONFIG_BOOTCOMMAND		""

/* Commands */
#define CONFIG_FAT_WRITE

#undef CONFIG_USB_GADGET_VBUS_DRAW
#define CONFIG_USB_GADGET_VBUS_DRAW	0
#define CONFIG_USBID_ADDR		0x34052c46

#define CONFIG_SYS_ICACHE_OFF
#define CONFIG_SYS_DCACHE_OFF
#define CONFIG_SYS_L2CACHE_OFF

#endif /* __BCM23550_W1D_H */
Commit	Line	Data
43486e4c SR	1	/*
	2	* Copyright 2013 Broadcom Corporation.
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	#ifndef __BCM23550_W1D_H
	8	#define __BCM23550_W1D_H
	9
	10	#include <linux/sizes.h>
	11	#include <asm/arch/sysmap.h>
	12
	13	/* CPU, chip, mach, etc */
	14	#define CONFIG_KONA
	15	#define CONFIG_SKIP_LOWLEVEL_INIT
	16	#define CONFIG_KONA_RESET_S
	17
	18	/*
	19	* Memory configuration
	20	*/
	21	#define CONFIG_SYS_TEXT_BASE 0x9f000000
	22
	23	#define CONFIG_SYS_SDRAM_BASE 0x80000000
	24	#define CONFIG_SYS_SDRAM_SIZE 0x20000000
	25	#define CONFIG_NR_DRAM_BANKS 1
	26
	27	#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */
	28	#define CONFIG_STACKSIZE SZ_256K
	29
	30	/* GPIO Driver */
	31	#define CONFIG_KONA_GPIO
	32
	33	/* MMC/SD Driver */
	34	#define CONFIG_SDHCI
	35	#define CONFIG_MMC_SDMA
	36	#define CONFIG_KONA_SDHCI
	37	#define CONFIG_MMC
	38	#define CONFIG_GENERIC_MMC
	39
	40	#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
	41	#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
	42	#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
	43	#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
	44	#define CONFIG_SYS_SDIO0_MAX_CLK 48000000
	45	#define CONFIG_SYS_SDIO1_MAX_CLK 48000000
	46	#define CONFIG_SYS_SDIO2_MAX_CLK 48000000
	47	#define CONFIG_SYS_SDIO3_MAX_CLK 48000000
	48	#define CONFIG_SYS_SDIO0 "sdio1"
	49	#define CONFIG_SYS_SDIO1 "sdio2"
	50	#define CONFIG_SYS_SDIO2 "sdio3"
	51	#define CONFIG_SYS_SDIO3 "sdio4"
	52
	53	/* I2C Driver */
	54	#define CONFIG_SYS_I2C
	55	#define CONFIG_SYS_I2C_KONA
	56	#define CONFIG_SYS_SPD_BUS_NUM 3 /* Start with PMU bus */
	57	#define CONFIG_SYS_MAX_I2C_BUS 4
	58	#define CONFIG_SYS_I2C_BASE0 BSC1_BASE_ADDR
	59	#define CONFIG_SYS_I2C_BASE1 BSC2_BASE_ADDR
	60	#define CONFIG_SYS_I2C_BASE2 BSC3_BASE_ADDR
	61	#define CONFIG_SYS_I2C_BASE3 PMU_BSC_BASE_ADDR
	62
	63	/* Timer Driver */
	64	#define CONFIG_SYS_TIMER_RATE 32000
65	#define CONFIG_SYS_TIMER_COUNTER (TIMER_BASE_ADDR + 4) /* STCLO offset */
66
67	/* Init functions */
68	#define CONFIG_MISC_INIT_R /* board's misc_init_r function */
69
70	/* Some commands use this as the default load address */
71	#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
72
73	/* No mtest functions as recommended */
74
75	/*
76	* This is the initial SP which is used only briefly for relocating the u-boot
77	* image to the top of SDRAM. After relocation u-boot moves the stack to the
78	* proper place.
79	*/
80	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
81
82	/* Serial Info */
83	#define CONFIG_SYS_NS16550_SERIAL
84	/* Post pad 3 bytes after each reg addr */
85	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
86	#define CONFIG_SYS_NS16550_CLK 13000000
87	#define CONFIG_CONS_INDEX 1
88	#define CONFIG_SYS_NS16550_COM1 0x3e000000
89
90	#define CONFIG_BAUDRATE 115200
91
92	/* must fit into GPT:u-boot-env partition */
93	#define CONFIG_ENV_IS_IN_MMC
94	#define CONFIG_SYS_MMC_ENV_DEV 0
95	#define CONFIG_ENV_OFFSET (0x00011a00 * 512)
96	#define CONFIG_ENV_SIZE (8 * 512)
97
98	#define CONFIG_SYS_NO_FLASH /* Not using NAND/NOR unmanaged flash */
99
100	/* console configuration */
101	#define CONFIG_SYS_CBSIZE 1024 /* Console buffer size */
102	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
103	sizeof(CONFIG_SYS_PROMPT) + 16) /* Printbuffer size */
104	#define CONFIG_SYS_MAXARGS 64
105	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
106
107	/*
108	* One partition type must be defined for part.c
109	* This is necessary for the fatls command to work on an SD card
110	* for example.
111	*/
112	#define CONFIG_DOS_PARTITION
113	#define CONFIG_EFI_PARTITION
114
115	/* version string, parser, etc */
43486e4c SR	116	#define CONFIG_AUTO_COMPLETE
	117	#define CONFIG_CMDLINE_EDITING
	118	#define CONFIG_SYS_LONGHELP
	119
	120	#define CONFIG_CRC32_VERIFY
	121	#define CONFIG_MX_CYCLIC
	122
	123	/* Initial upstream - boot to cmd prompt only */
	124	#define CONFIG_BOOTCOMMAND ""
	125
	126	/* Commands */
	127	#define CONFIG_FAT_WRITE
	128
43486e4c SR	129	#undef CONFIG_USB_GADGET_VBUS_DRAW
43486e4c SR	130	#define CONFIG_USB_GADGET_VBUS_DRAW 0
43486e4c SR	131	#define CONFIG_USBID_ADDR 0x34052c46
	132
	133	#define CONFIG_SYS_ICACHE_OFF
	134	#define CONFIG_SYS_DCACHE_OFF
	135	#define CONFIG_SYS_L2CACHE_OFF
	136
	137	#endif /* __BCM23550_W1D_H */