[people/ms/u-boot.git] / include / configs / bcm28155_ap.h

/*
 * Copyright 2013 Broadcom Corporation.
 *
 * SPDX-License-Identifier:      GPL-2.0+
 */

#ifndef __BCM28155_AP_H
#define __BCM28155_AP_H

#include <linux/sizes.h>
#include <asm/arch/sysmap.h>

/* CPU, chip, mach, etc */
#define CONFIG_KONA
#define CONFIG_SKIP_LOWLEVEL_INIT

/*
 * Memory configuration
 */

#define CONFIG_SYS_SDRAM_BASE		0x80000000
#define CONFIG_SYS_SDRAM_SIZE		0x80000000
#define CONFIG_NR_DRAM_BANKS		1

#define CONFIG_SYS_MALLOC_LEN		SZ_4M	/* see armv7/start.S. */

/* GPIO Driver */
#define CONFIG_KONA_GPIO

/* MMC/SD Driver */
#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
#define CONFIG_SYS_SDIO0_MAX_CLK 48000000
#define CONFIG_SYS_SDIO1_MAX_CLK 48000000
#define CONFIG_SYS_SDIO2_MAX_CLK 48000000
#define CONFIG_SYS_SDIO3_MAX_CLK 48000000
#define CONFIG_SYS_SDIO0 "sdio1"
#define CONFIG_SYS_SDIO1 "sdio2"
#define CONFIG_SYS_SDIO2 "sdio3"
#define CONFIG_SYS_SDIO3 "sdio4"

/* I2C Driver */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_KONA
#define CONFIG_SYS_SPD_BUS_NUM	3	/* Start with PMU bus */
#define CONFIG_SYS_MAX_I2C_BUS	4
#define CONFIG_SYS_I2C_BASE0	BSC1_BASE_ADDR
#define CONFIG_SYS_I2C_BASE1	BSC2_BASE_ADDR
#define CONFIG_SYS_I2C_BASE2	BSC3_BASE_ADDR
#define CONFIG_SYS_I2C_BASE3	PMU_BSC_BASE_ADDR

/* Timer Driver */
#define CONFIG_SYS_TIMER_RATE		32000
#define CONFIG_SYS_TIMER_COUNTER	(TIMER_BASE_ADDR + 4) /* STCLO offset */

/* Init functions */
#define CONFIG_MISC_INIT_R	/* board's misc_init_r function */

/* Some commands use this as the default load address */
#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE

/* No mtest functions as recommended */

/*
 * This is the initial SP which is used only briefly for relocating the u-boot
 * image to the top of SDRAM. After relocation u-boot moves the stack to the
 * proper place.
 */
#define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE

/* Serial Info */
#define CONFIG_SYS_NS16550_SERIAL
/* Post pad 3 bytes after each reg addr */
#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
#define CONFIG_SYS_NS16550_CLK		13000000
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550_COM1		0x3e000000

/* must fit into GPT:u-boot-env partition */
#define CONFIG_SYS_MMC_ENV_DEV		0
#define CONFIG_ENV_OFFSET		(0x00011a00 * 512)
#define CONFIG_ENV_SIZE			(8 * 512)

/* console configuration */
#define CONFIG_SYS_CBSIZE		1024	/* Console buffer size */
#define CONFIG_SYS_MAXARGS		64
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

/*
 * One partition type must be defined for part.c
 * This is necessary for the fatls command to work on an SD card
 * for example.
 */

/* version string, parser, etc */

#define CONFIG_MX_CYCLIC

/* Initial upstream - boot to cmd prompt only */
#define CONFIG_BOOTCOMMAND		""

#define CONFIG_USBID_ADDR		0x34052c46

#endif /* __BCM28155_AP_H */
Commit	Line	Data
9ed679ae DR	1	/*
	2	* Copyright 2013 Broadcom Corporation.
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	#ifndef __BCM28155_AP_H
	8	#define __BCM28155_AP_H
	9
1ace4022	10	#include <linux/sizes.h>
9ed679ae DR	11	#include <asm/arch/sysmap.h>
9ed679ae DR	12
3fcfe803	13	/* CPU, chip, mach, etc */
9ed679ae DR	14	#define CONFIG_KONA
	15	#define CONFIG_SKIP_LOWLEVEL_INIT
	16
	17	/*
	18	* Memory configuration
	19	*/
9ed679ae DR	20
	21	#define CONFIG_SYS_SDRAM_BASE 0x80000000
	22	#define CONFIG_SYS_SDRAM_SIZE 0x80000000
	23	#define CONFIG_NR_DRAM_BANKS 1
	24
	25	#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */
9ed679ae DR	26
	27	/* GPIO Driver */
	28	#define CONFIG_KONA_GPIO
	29
	30	/* MMC/SD Driver */
9ed679ae DR	31	#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
	32	#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
	33	#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
	34	#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
	35	#define CONFIG_SYS_SDIO0_MAX_CLK 48000000
	36	#define CONFIG_SYS_SDIO1_MAX_CLK 48000000
	37	#define CONFIG_SYS_SDIO2_MAX_CLK 48000000
	38	#define CONFIG_SYS_SDIO3_MAX_CLK 48000000
	39	#define CONFIG_SYS_SDIO0 "sdio1"
	40	#define CONFIG_SYS_SDIO1 "sdio2"
	41	#define CONFIG_SYS_SDIO2 "sdio3"
	42	#define CONFIG_SYS_SDIO3 "sdio4"
	43
	44	/* I2C Driver */
	45	#define CONFIG_SYS_I2C
	46	#define CONFIG_SYS_I2C_KONA
	47	#define CONFIG_SYS_SPD_BUS_NUM 3 /* Start with PMU bus */
	48	#define CONFIG_SYS_MAX_I2C_BUS 4
	49	#define CONFIG_SYS_I2C_BASE0 BSC1_BASE_ADDR
	50	#define CONFIG_SYS_I2C_BASE1 BSC2_BASE_ADDR
	51	#define CONFIG_SYS_I2C_BASE2 BSC3_BASE_ADDR
	52	#define CONFIG_SYS_I2C_BASE3 PMU_BSC_BASE_ADDR
	53
	54	/* Timer Driver */
	55	#define CONFIG_SYS_TIMER_RATE 32000
	56	#define CONFIG_SYS_TIMER_COUNTER (TIMER_BASE_ADDR + 4) /* STCLO offset */
	57
	58	/* Init functions */
	59	#define CONFIG_MISC_INIT_R /* board's misc_init_r function */
	60
	61	/* Some commands use this as the default load address */
	62	#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
	63
	64	/* No mtest functions as recommended */
9ed679ae DR	65
	66	/*
	67	* This is the initial SP which is used only briefly for relocating the u-boot
	68	* image to the top of SDRAM. After relocation u-boot moves the stack to the
	69	* proper place.
	70	*/
	71	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
	72
	73	/* Serial Info */
9ed679ae DR	74	#define CONFIG_SYS_NS16550_SERIAL
	75	/* Post pad 3 bytes after each reg addr */
	76	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	77	#define CONFIG_SYS_NS16550_CLK 13000000
	78	#define CONFIG_CONS_INDEX 1
	79	#define CONFIG_SYS_NS16550_COM1 0x3e000000
	80
30b0195a	81	/* must fit into GPT:u-boot-env partition */
30b0195a SR	82	#define CONFIG_SYS_MMC_ENV_DEV 0
	83	#define CONFIG_ENV_OFFSET (0x00011a00 * 512)
	84	#define CONFIG_ENV_SIZE (8 * 512)
9ed679ae	85
9ed679ae DR	86	/* console configuration */
9ed679ae DR	87	#define CONFIG_SYS_CBSIZE 1024 /* Console buffer size */
9ed679ae DR	88	#define CONFIG_SYS_MAXARGS 64
	89	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	90
	91	/*
	92	* One partition type must be defined for part.c
	93	* This is necessary for the fatls command to work on an SD card
	94	* for example.
	95	*/
9ed679ae DR	96
9ed679ae DR	97	/* version string, parser, etc */
9ed679ae	98
9ed679ae DR	99	#define CONFIG_MX_CYCLIC
	100
	101	/* Initial upstream - boot to cmd prompt only */
	102	#define CONFIG_BOOTCOMMAND ""
	103
d00bf781	104	#define CONFIG_USBID_ADDR 0x34052c46
d00bf781	105
9ed679ae	106	#endif /* __BCM28155_AP_H */