[people/ms/u-boot.git] / include / configs / dlvision.h

/*
 * (C) Copyright 2009
 * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_405EP		1	/* this is a PPC405 CPU */
#define CONFIG_DLVISION	        1	/*  on a Neo board */

#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000

/*
 * Include common defines/options for all AMCC eval boards
 */
#define CONFIG_HOSTNAME		dlvision
#include "amcc-common.h"

#define CONFIG_MISC_INIT_R		/* call misc_init_r */

#define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll   */

/*
 * Configure PLL
 */
#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
#define PLLMR1_DEFAULT PLLMR1_266_133_66_33

#define CONFIG_ENV_IS_IN_FLASH	/* use FLASH for environment vars */

/*
 * Default environment variables
 */
#define	CONFIG_EXTRA_ENV_SETTINGS					\
	CONFIG_AMCC_DEF_ENV						\
	CONFIG_AMCC_DEF_ENV_POWERPC					\
	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
	"kernel_addr=fc000000\0"					\
	"fdt_addr=fc1e0000\0"						\
	"ramdisk_addr=fc200000\0"					\
	""

#define CONFIG_PHY_ADDR		4	/* PHY address			*/
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR	0xc	/* EMAC1 PHY address		*/
#define CONFIG_PHY_CLK_FREQ    EMAC_STACR_CLK_66MHZ

/*
 * Commands additional to the ones defined in amcc-common.h
 */
#undef CONFIG_CMD_IRQ

/*
 * SDRAM configuration (please see cpu/ppc/sdram.[ch])
 */
#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */

/* SDRAM timings used in datasheet */
#define CONFIG_SYS_SDRAM_CL             3	/* CAS latency */
#define CONFIG_SYS_SDRAM_tRP           20	/* PRECHARGE command period */
#define CONFIG_SYS_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE period */
#define CONFIG_SYS_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
#define CONFIG_SYS_SDRAM_tRFC          66	/* Auto refresh period */

/*
 * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
 * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
 * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD.
 * The Linux BASE_BAUD define should match this configuration.
 *    baseBaud = cpuClock/(uartDivisor*16)
 * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
 * set Linux BASE_BAUD to 403200.
 */
#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
#undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* external serial clock */
#undef  CONFIG_SYS_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
#define CONFIG_SYS_BASE_BAUD		691200

/*
 * I2C stuff
 */
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000

/*
 * FLASH organization
 */
#define CONFIG_SYS_FLASH_CFI		/* The flash is CFI compatible	*/
#define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/

#define CONFIG_SYS_FLASH_BASE		0xFC000000
#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sectors per chip*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase/ms */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write/ms */

#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buff'd writes */

#define CONFIG_SYS_FLASH_EMPTY_INFO	/* 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* no warn upon unknown flash */

#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector */
#define CONFIG_ENV_ADDR		((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
#define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector */

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
#endif

/*
 * PPC405 GPIO Configuration
 */
#define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO	Alternate1	*/ \
{ \
/* GPIO Core 0 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0	PerBLast */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO1	TS1E */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO2	TS2E */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO3	TS1O */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO4	TS2O */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_1      }, /* GPIO5	TS3 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO6	TS4 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO7	TS5 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO8	TS6 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO9	TrcClk */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10	PerCS1 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11	PerCS2 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12	PerCS3 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13	PerCS4 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14	PerAddr03 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15	PerAddr04 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16	PerAddr05 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17	IRQ0 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18	IRQ1 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19	IRQ2 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO20	IRQ3 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO21	IRQ4 */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO22	IRQ5 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO23	IRQ6 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24	UART0_DCD */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25	UART0_DSR */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26	UART0_RI */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27	UART0_DTR */ \
{ GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28	UART1_Rx */ \
{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29	UART1_Tx */ \
{ GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO30	RejectPkt0 */ \
{ GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO31	RejectPkt1 */ \
} \
}

/*
 * Definitions for initial stack pointer and data area (in data cache)
 */
/* use on chip memory (OCM) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM        1

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */
#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area */

#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * External Bus Controller (EBC) Setup
 */

/* Memory Bank 0 (NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB0AP		0x92015480
/* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB0CR		0xFC0DA000

/* Memory Bank 1 (NVRAM) initializatio */
#define CONFIG_SYS_EBC_PB1AP		0x92015480
/* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit  */
#define CONFIG_SYS_EBC_PB1CR		0xFB858000

/* Memory Bank 2 (UART) initialization */
#define CONFIG_UART_BASE		0x7f100000
#define CONFIG_SYS_EBC_PB2AP		0x92015480
/* BAS=0x7f1,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB2CR		0x7f118000

/* Memory Bank 3 (Latches) initialization */
#define CONFIG_SYS_LATCH_BASE		0x7f200000
#define CONFIG_SYS_EBC_PB3AP		0x92015480
/* BAS=0x7f2,BS=1MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB3CR		0x7f21a000

#endif	/* __CONFIG_H */
Commit	Line	Data
b209a114 DE	1	/*
	2	* (C) Copyright 2009
	3	* Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
	4	*
3765b3e7	5	* SPDX-License-Identifier: GPL-2.0+
b209a114 DE	6	*/
	7
	8	#ifndef __CONFIG_H
	9	#define __CONFIG_H
	10
	11	#define CONFIG_405EP 1 /* this is a PPC405 CPU */
b209a114 DE	12	#define CONFIG_DLVISION 1 /* on a Neo board */
b209a114 DE	13
2ae18241 WD	14	#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
2ae18241 WD	15
b209a114 DE	16	/*
	17	* Include common defines/options for all AMCC eval boards
	18	*/
	19	#define CONFIG_HOSTNAME dlvision
b209a114 DE	20	#include "amcc-common.h"
b209a114 DE	21
b209a114 DE	22	#define CONFIG_MISC_INIT_R /* call misc_init_r */
	23
	24	#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
	25
	26	/*
	27	* Configure PLL
	28	*/
	29	#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
	30	#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
	31
b209a114 DE	32	#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */
	33
	34	/*
	35	* Default environment variables
	36	*/
	37	#define CONFIG_EXTRA_ENV_SETTINGS \
	38	CONFIG_AMCC_DEF_ENV \
	39	CONFIG_AMCC_DEF_ENV_POWERPC \
	40	CONFIG_AMCC_DEF_ENV_NOR_UPD \
	41	"kernel_addr=fc000000\0" \
	42	"fdt_addr=fc1e0000\0" \
	43	"ramdisk_addr=fc200000\0" \
	44	""
	45
	46	#define CONFIG_PHY_ADDR 4 /* PHY address */
	47	#define CONFIG_HAS_ETH0
	48	#define CONFIG_HAS_ETH1
	49	#define CONFIG_PHY1_ADDR 0xc /* EMAC1 PHY address */
	50	#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ
	51
	52	/*
	53	* Commands additional to the ones defined in amcc-common.h
	54	*/
f9af10dd	55	#undef CONFIG_CMD_IRQ
b209a114 DE	56
	57	/*
	58	* SDRAM configuration (please see cpu/ppc/sdram.[ch])
	59	*/
	60	#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
	61
	62	/* SDRAM timings used in datasheet */
	63	#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */
	64	#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */
	65	#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE period */
	66	#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
	67	#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */
	68
	69	/*
	70	* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
	71	* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
	72	* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD.
	73	* The Linux BASE_BAUD define should match this configuration.
	74	* baseBaud = cpuClock/(uartDivisor*16)
	75	* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
	76	* set Linux BASE_BAUD to 403200.
	77	*/
550650dd	78	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
b209a114 DE	79	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
	80	#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
	81	#define CONFIG_SYS_BASE_BAUD 691200
	82
	83	/*
	84	* I2C stuff
	85	*/
880540de	86	#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
b209a114 DE	87
	88	/*
	89	* FLASH organization
	90	*/
	91	#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
	92	#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
	93
	94	#define CONFIG_SYS_FLASH_BASE 0xFC000000
	95	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	96
	97	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
	98	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors per chip*/
	99
	100	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms */
	101	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms */
	102
	103	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buff'd writes */
b209a114 DE	104
	105	#define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */
	106	#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* no warn upon unknown flash */
	107
	108	#ifdef CONFIG_ENV_IS_IN_FLASH
	109	#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
	110	#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
	111	#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
	112
	113	/* Address and size of Redundant Environment Sector */
	114	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
	115	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
	116	#endif
	117
	118	/*
	119	* PPC405 GPIO Configuration
	120	*/
	121	#define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \
	122	{ \
	123	/* GPIO Core 0 */ \
	124	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \
	125	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \
	126	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \
	127	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \
	128	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \
	129	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO5 TS3 */ \
	130	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO6 TS4 */ \
	131	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO7 TS5 */ \
	132	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \
	133	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO9 TrcClk */ \
	134	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \
	135	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \
	136	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \
	137	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \
	138	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \
	139	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \
	140	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \
	141	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \
	142	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \
	143	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \
	144	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \
	145	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \
	146	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \
	147	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \
	148	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \
	149	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \
	150	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \
	151	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \
	152	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \
	153	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \
	154	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \
	155	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \
	156	} \
	157	}
	158
	159	/*
	160	* Definitions for initial stack pointer and data area (in data cache)
	161	*/
	162	/* use on chip memory (OCM) for temperary stack until sdram is tested */
	163	#define CONFIG_SYS_TEMP_STACK_OCM 1
	164
	165	/* On Chip Memory location */
	166	#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
	167	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
168	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */
553f0982	169	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area */
b209a114	170
b209a114	171	#define CONFIG_SYS_GBL_DATA_OFFSET \
25ddd1fb	172	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
b209a114 DE	173	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	174
	175	/*
	176	* External Bus Controller (EBC) Setup
	177	*/
	178
	179	/* Memory Bank 0 (NOR-FLASH) initialization */
	180	#define CONFIG_SYS_EBC_PB0AP 0x92015480
	181	/* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit */
	182	#define CONFIG_SYS_EBC_PB0CR 0xFC0DA000
	183
	184	/* Memory Bank 1 (NVRAM) initializatio */
	185	#define CONFIG_SYS_EBC_PB1AP 0x92015480
	186	/* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
	187	#define CONFIG_SYS_EBC_PB1CR 0xFB858000
	188
	189	/* Memory Bank 2 (UART) initialization */
	190	#define CONFIG_UART_BASE 0x7f100000
	191	#define CONFIG_SYS_EBC_PB2AP 0x92015480
	192	/* BAS=0x7f1,BS=1MB,BU=R/W,BW=8bit */
	193	#define CONFIG_SYS_EBC_PB2CR 0x7f118000
	194
	195	/* Memory Bank 3 (Latches) initialization */
	196	#define CONFIG_SYS_LATCH_BASE 0x7f200000
	197	#define CONFIG_SYS_EBC_PB3AP 0x92015480
	198	/* BAS=0x7f2,BS=1MB,BU=R/W,BW=16bit */
	199	#define CONFIG_SYS_EBC_PB3CR 0x7f21a000
	200
	201	#endif /* __CONFIG_H */