[people/ms/u-boot.git] / include / configs / km / kmp204x-common.h

/*
 * (C) Copyright 2013 Keymile AG
 * Valentin Longchamp <valentin.longchamp@keymile.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _CONFIG_KMP204X_H
#define _CONFIG_KMP204X_H

#define CONFIG_PHYS_64BIT
#define CONFIG_PPC_P2041

#define CONFIG_SYS_TEXT_BASE	0xfff40000

#define CONFIG_KM_DEF_NETDEV	"netdev=eth0\0"

/* an additionnal option is required for UBI as subpage access is
 * supported in u-boot */
#define CONFIG_KM_UBI_PART_BOOT_OPTS		",2048"

#define CONFIG_NAND_ECC_BCH

#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO

/* common KM defines */
#include "keymile-common.h"

#define CONFIG_SYS_RAMBOOT
#define CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg

/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500			/* BOOKE e500 family */
#define CONFIG_E500MC			/* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
#define CONFIG_MP			/* support multiple processors */

#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
#define CONFIG_FSL_ELBC			/* Has Enhanced localbus controller */
#define CONFIG_PCI			/* Enable PCI/PCIE */
#define CONFIG_PCIE1			/* PCIE controler 1 */
#define CONFIG_PCIE3			/* PCIE controler 3 */
#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */

#define CONFIG_SYS_DPAA_RMAN		/* RMan */

#define CONFIG_FSL_LAW			/* Use common FSL init code */

/* Environment in SPI Flash */
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS              0
#define CONFIG_ENV_SPI_CS               0
#define CONFIG_ENV_SPI_MAX_HZ           20000000
#define CONFIG_ENV_SPI_MODE             0
#define CONFIG_ENV_OFFSET               0x100000	/* 1MB for u-boot */
#define CONFIG_ENV_SIZE			0x004000	/* 16K env */
#define CONFIG_ENV_SECT_SIZE            0x010000
#define CONFIG_ENV_OFFSET_REDUND	0x110000
#define CONFIG_ENV_TOTAL_SIZE		0x020000

#define CONFIG_SYS_REDUNDAND_ENVIRONMENT

#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(unsigned long dummy);
#endif
#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BACKSIDE_L2_CACHE
#define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
#define CONFIG_BTB			/* toggle branch predition */

#define CONFIG_ENABLE_36BIT_PHYS

#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */

#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS	/* POST memory regions test */

/*
 *  Config the L3 Cache as L3 SRAM
 */
#define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
#define CONFIG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | \
		CONFIG_RAMBOOT_TEXT_BASE)
#define CONFIG_SYS_L3_SIZE		(1024 << 10)
#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)

#define CONFIG_SYS_DCSRBAR		0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull

/*
 * DDR Setup
 */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_DIMM_SLOTS_PER_CTLR	1
#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)

#define CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE

#define CONFIG_SYS_SPD_BUS_NUM	0
#define SPD_EEPROM_ADDRESS	0x54
#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */

#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2

/******************************************************************************
 * (PRAM usage)
 * ... -------------------------------------------------------
 * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
 * ... |<------------------- pram -------------------------->|
 * ... -------------------------------------------------------
 * @END_OF_RAM:
 * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
 * @CONFIG_KM_PHRAM: address for /var
 * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
 * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
 */

/* size of rootfs in RAM */
#define CONFIG_KM_ROOTFSSIZE	0x0
/* pseudo-non volatile RAM [hex] */
#define CONFIG_KM_PNVRAM	0x80000
/* physical RAM MTD size [hex] */
#define CONFIG_KM_PHRAM		0x100000
/* reserved pram area at the end of memory [hex]
 * u-boot reserves some memory for the MP boot page */
#define CONFIG_KM_RESERVED_PRAM	0x1000
/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
 * is not valid yet, which is the case for when u-boot copies itself to RAM */
#define CONFIG_PRAM		((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10)

#define CONFIG_KM_CRAMFS_ADDR	0x2000000
#define CONFIG_KM_KERNEL_ADDR	0x1000000	/* max kernel size 15.5Mbytes */
#define CONFIG_KM_FDT_ADDR	0x1F80000	/* max dtb    size  0.5Mbytes */

/*
 * Local Bus Definitions
 */

/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
#define CONFIG_SYS_LBC_LCRR		(LCRR_CLKDIV_8 | LCRR_EADC_2)

/* Nand Flash */
#define CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_BASE		0xffa00000
#define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull

#define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)

#define CONFIG_BCH

/* NAND flash config */
#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
			       | BR_PS_8	       /* Port Size = 8 bit */ \
			       | BR_MS_FCM	       /* MSEL = FCM */ \
			       | BR_V)		       /* valid */

#define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB	      /* length 256K */ \
			       | OR_FCM_BCTLD	/* LBCTL not ass */	\
			       | OR_FCM_SCY_1	/* 1 clk wait cycle */	\
			       | OR_FCM_RST	/* 1 clk read setup */	\
			       | OR_FCM_PGS	/* Large page size */	\
			       | OR_FCM_CST)	/* 0.25 command setup */

#define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

/* QRIO FPGA */
#define CONFIG_SYS_QRIO_BASE		0xfb000000
#define CONFIG_SYS_QRIO_BASE_PHYS	0xffb000000ull

#define CONFIG_SYS_QRIO_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
				| BR_PS_8	/* Port Size 8 bits */ \
				| BR_DECC_OFF	/* no error corr */ \
				| BR_MS_GPCM	/* MSEL = GPCM */ \
				| BR_V)		/* valid */

#define CONFIG_SYS_QRIO_OR_PRELIM  (OR_AM_64KB	/* length 64K */ \
				| OR_GPCM_BCTLD /* no LCTL assert */ \
				| OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
				| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
				| OR_GPCM_TRLX /* relaxed tmgs */ \
				| OR_GPCM_EAD) /* extra bus clk cycles */

#define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
#define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */

/* bootcounter in QRIO */
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_SYS_BOOTCOUNT_ADDR	(CONFIG_SYS_QRIO_BASE + 0x20)

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
#define CONFIG_MISC_INIT_F
#define CONFIG_MISC_INIT_R
#define CONFIG_LAST_STAGE_INIT

#define CONFIG_HWCONFIG

/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
					GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)

/* Serial Port - controlled on board with jumper J8
 * open - index 2
 * shorted - index 1
 */
#define CONFIG_CONS_INDEX	1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)

#define CONFIG_KM_CONSOLE_TTY	"ttyS0"

/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER

/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS

/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */

/* I2C */

#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_INIT_BOARD
#define CONFIG_SYS_I2C_SPEED		100000 /* deblocking */
#define CONFIG_SYS_NUM_I2C_BUSES	3
#define CONFIG_SYS_I2C_MAX_HOPS		1
#define CONFIG_SYS_I2C_FSL		/* Use FSL I2C driver */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
#define CONFIG_SYS_I2C_BUSES	{	{0, {I2C_NULL_HOP} }, \
					{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
					{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
				}
#ifndef __ASSEMBLY__
void set_sda(int state);
void set_scl(int state);
int get_sda(void);
int get_scl(void);
#endif

#define CONFIG_KM_IVM_BUS		1	/* I2C1 (Mux-Port 1)*/

/*
 * eSPI - Enhanced SPI
 */
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_BAR	/* 4 byte-addressing */
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED         20000000
#define CONFIG_SF_DEFAULT_MODE          0

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */

/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8010000
#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8010000ull
#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */

/* Qman/Bman */
#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS	10
#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
#define CONFIG_SYS_QMAN_NUM_PORTALS	10
#define CONFIG_SYS_QMAN_MEM_BASE	0xf4200000
#define CONFIG_SYS_QMAN_MEM_PHYS	0xff4200000ull
#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000

#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
/* Default address of microcode for the Linux Fman driver
 * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
 * ucode is stored after env, so we got 0x120000.
 */
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR	0x120000
#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

#define CONFIG_FMAN_ENET
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_MARVELL		/* there is a marvell phy */

#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_PNP			/* do pci plug-and-play */
#define CONFIG_E1000

#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
#define CONFIG_DOS_PARTITION

/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR	0x11
#define CONFIG_SYS_TBIPA_VALUE	8
#define CONFIG_PHYLIB		/* recommended PHY management */
#define CONFIG_ETHPRIME		"FM1@DTSEC5"
#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */

/*
 * Environment
 */
#define CONFIG_LOADS_ECHO		/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

/*
 * Hardware Watchdog
 */
#define CONFIG_WATCHDOG			/* enable CPU watchdog */
#define CONFIG_WATCHDOG_PRESC 34	/* wdog prescaler 2^(64-34) (~10min) */
#define CONFIG_WATCHDOG_RC WRC_CHIP	/* reset chip on watchdog event */


/*
 * additionnal command line configuration.
 */
#define CONFIG_CMD_PCI
#define CONFIG_CMD_NET
#define CONFIG_CMD_ERRATA

/* we don't need flash support */
#define CONFIG_SYS_NO_FLASH
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_FLASH
#undef CONFIG_FLASH_CFI_MTD
#undef CONFIG_JFFS2_CMDLINE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux */
#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#endif

#define __USB_PHY_TYPE	utmi

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE
#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
#define CONFIG_KM_DEF_ENV "km-common=empty\0"
#endif

#ifndef MTDIDS_DEFAULT
# define MTDIDS_DEFAULT		"nand0=fsl_elbc_nand"
#endif /* MTDIDS_DEFAULT */

#ifndef MTDPARTS_DEFAULT
# define MTDPARTS_DEFAULT	"mtdparts="			\
	"fsl_elbc_nand:"						\
		"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
#endif /* MTDPARTS_DEFAULT */

/* architecture specific default bootargs */
#define CONFIG_KM_DEF_BOOT_ARGS_CPU		""

/* FIXME: FDT_ADDR is unspecified */
#define CONFIG_KM_DEF_ENV_CPU						\
	"boot=bootm ${load_addr_r} - ${fdt_addr_r}\0"			\
	"cramfsloadfdt="						\
		"cramfsload ${fdt_addr_r} "				\
		"fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0"		\
	"fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0"		\
	"u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0"		\
	"update="							\
		"sf probe 0;sf erase 0 +${filesize};"			\
		"sf write ${load_addr_r} 0 ${filesize};\0"		\
	"set_fdthigh=true\0"						\
	""

#define CONFIG_HW_ENV_SETTINGS						\
	"hwconfig=fsl_ddr:ctlr_intlv=cacheline\0"			\
	"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"		\
	"usb_dr_mode=host\0"

#define CONFIG_KM_NEW_ENV						\
	"newenv=sf probe 0;"						\
		"sf erase " __stringify(CONFIG_ENV_OFFSET) " "		\
		__stringify(CONFIG_ENV_TOTAL_SIZE)"\0"

/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
#ifndef CONFIG_KM_DEF_ARCH
#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
#endif

#define CONFIG_EXTRA_ENV_SETTINGS					\
	CONFIG_KM_DEF_ENV						\
	CONFIG_KM_DEF_ARCH						\
	CONFIG_KM_NEW_ENV						\
	CONFIG_HW_ENV_SETTINGS						\
	"EEprom_ivm=pca9547:70:9\0"					\
	""

#endif /* _CONFIG_KMP204X_H */
Commit	Line	Data
877bfe37 VL	1	/*
	2	* (C) Copyright 2013 Keymile AG
	3	* Valentin Longchamp <valentin.longchamp@keymile.com>
	4	*
	5	* SPDX-License-Identifier: GPL-2.0+
	6	*/
	7
	8	#ifndef _CONFIG_KMP204X_H
	9	#define _CONFIG_KMP204X_H
	10
	11	#define CONFIG_PHYS_64BIT
	12	#define CONFIG_PPC_P2041
	13
a5fbe742	14	#define CONFIG_SYS_TEXT_BASE 0xfff40000
877bfe37 VL	15
	16	#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0"
	17
cf7707a1 VL	18	/* an additionnal option is required for UBI as subpage access is
	19	* supported in u-boot */
	20	#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
	21
877bfe37 VL	22	#define CONFIG_NAND_ECC_BCH
877bfe37 VL	23
a0744285 VL	24	#define CONFIG_SYS_GENERIC_BOARD
	25	#define CONFIG_DISPLAY_BOARDINFO
	26
877bfe37 VL	27	/* common KM defines */
	28	#include "keymile-common.h"
	29
	30	#define CONFIG_SYS_RAMBOOT
	31	#define CONFIG_RAMBOOT_PBL
	32	#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
	33	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
e4536f8e MY	34	#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
e4536f8e MY	35	#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
877bfe37 VL	36
	37	/* High Level Configuration Options */
	38	#define CONFIG_BOOKE
	39	#define CONFIG_E500 /* BOOKE e500 family */
	40	#define CONFIG_E500MC /* BOOKE e500mc family */
	41	#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
877bfe37 VL	42	#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
	43	#define CONFIG_MP /* support multiple processors */
	44
	45	#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
	46	#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
	47	#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
	48	#define CONFIG_PCI /* Enable PCI/PCIE */
	49	#define CONFIG_PCIE1 /* PCIE controler 1 */
	50	#define CONFIG_PCIE3 /* PCIE controler 3 */
	51	#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
	52	#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
	53
	54	#define CONFIG_SYS_DPAA_RMAN /* RMan */
	55
	56	#define CONFIG_FSL_LAW /* Use common FSL init code */
	57
	58	/* Environment in SPI Flash */
	59	#define CONFIG_SYS_EXTRA_ENV_RELOC
	60	#define CONFIG_ENV_IS_IN_SPI_FLASH
	61	#define CONFIG_ENV_SPI_BUS 0
	62	#define CONFIG_ENV_SPI_CS 0
	63	#define CONFIG_ENV_SPI_MAX_HZ 20000000
	64	#define CONFIG_ENV_SPI_MODE 0
	65	#define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */
	66	#define CONFIG_ENV_SIZE 0x004000 /* 16K env */
	67	#define CONFIG_ENV_SECT_SIZE 0x010000
	68	#define CONFIG_ENV_OFFSET_REDUND 0x110000
	69	#define CONFIG_ENV_TOTAL_SIZE 0x020000
	70
	71	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	72
	73	#ifndef __ASSEMBLY__
	74	unsigned long get_board_sys_clk(unsigned long dummy);
	75	#endif
	76	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
	77
	78	/*
	79	* These can be toggled for performance analysis, otherwise use default.
	80	*/
	81	#define CONFIG_SYS_CACHE_STASHING
	82	#define CONFIG_BACKSIDE_L2_CACHE
	83	#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
	84	#define CONFIG_BTB /* toggle branch predition */
	85
	86	#define CONFIG_ENABLE_36BIT_PHYS
	87
	88	#define CONFIG_ADDR_MAP
	89	#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
	90
18794944	91	#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
877bfe37 VL	92
	93	/*
	94	* Config the L3 Cache as L3 SRAM
	95	*/
	96	#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
	97	#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull \| \
	98	CONFIG_RAMBOOT_TEXT_BASE)
	99	#define CONFIG_SYS_L3_SIZE (1024 << 10)
	100	#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
	101
	102	#define CONFIG_SYS_DCSRBAR 0xf0000000
	103	#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
	104
	105	/*
	106	* DDR Setup
	107	*/
	108	#define CONFIG_VERY_BIG_RAM
	109	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	110	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	111
	112	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	113	#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
	114
	115	#define CONFIG_DDR_SPD
5614e71b	116	#define CONFIG_SYS_FSL_DDR3
877bfe37 VL	117	#define CONFIG_FSL_DDR_INTERACTIVE
	118
	119	#define CONFIG_SYS_SPD_BUS_NUM 0
	120	#define SPD_EEPROM_ADDRESS 0x54
	121	#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
	122
	123	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
	124	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	125
	126	/******************************************************************************
	127	* (PRAM usage)
	128	* ... -------------------------------------------------------
	129	* ... \|ROOTFSSIZE \| PNVRAM \|PHRAM \|RESERVED_PRAM \| END_OF_RAM
	130	* ... \|<------------------- pram -------------------------->\|
	131	* ... -------------------------------------------------------
	132	* @END_OF_RAM:
	133	* @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
	134	* @CONFIG_KM_PHRAM: address for /var
	135	* @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
	136	* @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
	137	*/
	138
	139	/* size of rootfs in RAM */
	140	#define CONFIG_KM_ROOTFSSIZE 0x0
	141	/* pseudo-non volatile RAM [hex] */
	142	#define CONFIG_KM_PNVRAM 0x80000
	143	/* physical RAM MTD size [hex] */
	144	#define CONFIG_KM_PHRAM 0x100000
848b31ab VL	145	/* reserved pram area at the end of memory [hex]
	146	* u-boot reserves some memory for the MP boot page */
	147	#define CONFIG_KM_RESERVED_PRAM 0x1000
	148	/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
	149	* is not valid yet, which is the case for when u-boot copies itself to RAM */
	150	#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10)
877bfe37 VL	151
	152	#define CONFIG_KM_CRAMFS_ADDR 0x2000000
	153	#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
	154	#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */
	155
877bfe37 VL	156	/*
	157	* Local Bus Definitions
	158	*/
	159
	160	/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
	161	#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 \| LCRR_EADC_2)
	162
	163	/* Nand Flash */
	164	#define CONFIG_NAND_FSL_ELBC
	165	#define CONFIG_SYS_NAND_BASE 0xffa00000
	166	#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
	167
	168	#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
	169	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	170	#define CONFIG_MTD_NAND_VERIFY_WRITE
	171	#define CONFIG_CMD_NAND
	172	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
	173
	174	#define CONFIG_BCH
	175
	176	/* NAND flash config */
	177	#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	178	\| BR_PS_8 /* Port Size = 8 bit */ \
	179	\| BR_MS_FCM /* MSEL = FCM */ \
	180	\| BR_V) /* valid */
	181
	182	#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
	183	\| OR_FCM_BCTLD /* LBCTL not ass */ \
	184	\| OR_FCM_SCY_1 /* 1 clk wait cycle */ \
	185	\| OR_FCM_RST /* 1 clk read setup */ \
	186	\| OR_FCM_PGS /* Large page size */ \
	187	\| OR_FCM_CST) /* 0.25 command setup */
	188
	189	#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
	190	#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
	191
	192	/* QRIO FPGA */
	193	#define CONFIG_SYS_QRIO_BASE 0xfb000000
	194	#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull
	195
	196	#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
	197	\| BR_PS_8 /* Port Size 8 bits */ \
	198	\| BR_DECC_OFF /* no error corr */ \
	199	\| BR_MS_GPCM /* MSEL = GPCM */ \
	200	\| BR_V) /* valid */
	201
	202	#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \
	203	\| OR_GPCM_BCTLD /* no LCTL assert */ \
	204	\| OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
	205	\| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
	206	\| OR_GPCM_TRLX /* relaxed tmgs */ \
	207	\| OR_GPCM_EAD) /* extra bus clk cycles */
	208
	209	#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
	210	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
	211
dd21f096 RB	212	/* bootcounter in QRIO */
	213	#define CONFIG_BOOTCOUNT_LIMIT
	214	#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20)
	215
877bfe37 VL	216	#define CONFIG_BOARD_EARLY_INIT_F
877bfe37 VL	217	#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
f3e74d0a	218	#define CONFIG_MISC_INIT_F
877bfe37 VL	219	#define CONFIG_MISC_INIT_R
	220	#define CONFIG_LAST_STAGE_INIT
	221
	222	#define CONFIG_HWCONFIG
	223
	224	/* define to use L1 as initial stack */
	225	#define CONFIG_L1_INIT_RAM
	226	#define CONFIG_SYS_INIT_RAM_LOCK
	227	#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
	228	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
	229	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
	230	/* The assembler doesn't like typecast */
	231	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
	232	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) \| \
	233	CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
	234	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
	235
	236	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
	237	GENERATED_GBL_DATA_SIZE)
	238	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	239
	240	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
a5fbe742	241	#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
877bfe37 VL	242	#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
	243
	244	/* Serial Port - controlled on board with jumper J8
	245	* open - index 2
	246	* shorted - index 1
	247	*/
	248	#define CONFIG_CONS_INDEX 1
	249	#define CONFIG_SYS_NS16550
	250	#define CONFIG_SYS_NS16550_SERIAL
	251	#define CONFIG_SYS_NS16550_REG_SIZE 1
	252	#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
	253
	254	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
	255	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
	256	#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
	257	#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
	258
	259	#define CONFIG_KM_CONSOLE_TTY "ttyS0"
	260
	261	/* Use the HUSH parser */
	262	#define CONFIG_SYS_HUSH_PARSER
	263
	264	/* pass open firmware flat tree */
	265	#define CONFIG_OF_LIBFDT
	266	#define CONFIG_OF_BOARD_SETUP
	267	#define CONFIG_OF_STDOUT_VIA_ALIAS
	268
	269	/* new uImage format support */
	270	#define CONFIG_FIT
	271	#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
	272
	273	/* I2C */
f3e74d0a	274
877bfe37	275	#define CONFIG_SYS_I2C
f3e74d0a RB	276	#define CONFIG_SYS_I2C_INIT_BOARD
f3e74d0a RB	277	#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */
877bfe37 VL	278	#define CONFIG_SYS_NUM_I2C_BUSES 3
	279	#define CONFIG_SYS_I2C_MAX_HOPS 1
	280	#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
	281	#define CONFIG_I2C_MULTI_BUS
	282	#define CONFIG_I2C_CMD_TREE
	283	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	284	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	285	#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
	286	#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
	287	{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
	288	{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
	289	}
f3e74d0a RB	290	#ifndef __ASSEMBLY__
	291	void set_sda(int state);
	292	void set_scl(int state);
	293	int get_sda(void);
	294	int get_scl(void);
	295	#endif
877bfe37 VL	296
	297	#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
	298
	299	/*
	300	* eSPI - Enhanced SPI
	301	*/
	302	#define CONFIG_FSL_ESPI
	303	#define CONFIG_SPI_FLASH
	304	#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */
	305	#define CONFIG_SPI_FLASH_STMICRO
47c1180c	306	#define CONFIG_SPI_FLASH_SPANSION
877bfe37 VL	307	#define CONFIG_CMD_SF
	308	#define CONFIG_SF_DEFAULT_SPEED 20000000
	309	#define CONFIG_SF_DEFAULT_MODE 0
	310
	311	/*
	312	* General PCI
	313	* Memory space is mapped 1-1, but I/O space must start from 0.
	314	*/
	315
	316	/* controller 1, direct to uli, tgtid 3, Base address 20000 */
	317	#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
	318	#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
	319	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
	320	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
	321	#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
	322	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	323	#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
	324	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
	325
	326	/* controller 3, Slot 1, tgtid 1, Base address 202000 */
	327	#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
	328	#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
	329	#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
	330	#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
	331	#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000
	332	#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
	333	#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull
	334	#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
	335
	336	/* Qman/Bman */
	337	#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
	338	#define CONFIG_SYS_BMAN_NUM_PORTALS 10
	339	#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
	340	#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
	341	#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
	342	#define CONFIG_SYS_QMAN_NUM_PORTALS 10
	343	#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
	344	#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
	345	#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
	346
	347	#define CONFIG_SYS_DPAA_FMAN
	348	#define CONFIG_SYS_DPAA_PME
	349	/* Default address of microcode for the Linux Fman driver
	350	* env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
	351	* ucode is stored after env, so we got 0x120000.
	352	*/
	353	#define CONFIG_SYS_QE_FW_IN_SPIFLASH
dcf1d774	354	#define CONFIG_SYS_FMAN_FW_ADDR 0x120000
877bfe37 VL	355	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	356	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
	357
	358	#define CONFIG_FMAN_ENET
	359	#define CONFIG_PHYLIB_10G
	360	#define CONFIG_PHY_MARVELL /* there is a marvell phy */
	361
	362	#define CONFIG_PCI_INDIRECT_BRIDGE
	363	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	364	#define CONFIG_E1000
	365
	366	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	367	#define CONFIG_DOS_PARTITION
	368
	369	/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
	370	#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11
	371	#define CONFIG_SYS_TBIPA_VALUE 8
	372	#define CONFIG_PHYLIB /* recommended PHY management */
	373	#define CONFIG_ETHPRIME "FM1@DTSEC5"
	374	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
	375
	376	/*
	377	* Environment
	378	*/
	379	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	380	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
	381
88ac6ffa BR	382	/*
	383	* Hardware Watchdog
	384	*/
	385	#define CONFIG_WATCHDOG /* enable CPU watchdog */
	386	#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
	387	#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
	388
	389
877bfe37 VL	390	/*
	391	* additionnal command line configuration.
	392	*/
	393	#define CONFIG_CMD_PCI
	394	#define CONFIG_CMD_NET
522641a7	395	#define CONFIG_CMD_ERRATA
877bfe37 VL	396
	397	/* we don't need flash support */
	398	#define CONFIG_SYS_NO_FLASH
	399	#undef CONFIG_CMD_IMLS
	400	#undef CONFIG_CMD_FLASH
	401	#undef CONFIG_FLASH_CFI_MTD
	402	#undef CONFIG_JFFS2_CMDLINE
	403
	404	/*
	405	* For booting Linux, the board info and command line data
	406	* have to be in the first 64 MB of memory, since this is
	407	* the maximum mapped by the Linux kernel during initialization.
	408	*/
	409	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
	410	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
	411
	412	#ifdef CONFIG_CMD_KGDB
	413	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
877bfe37 VL	414	#endif
	415
	416	#define __USB_PHY_TYPE utmi
	417
	418	/*
	419	* Environment Configuration
	420	*/
	421	#define CONFIG_ENV_OVERWRITE
	422	#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
	423	#define CONFIG_KM_DEF_ENV "km-common=empty\0"
	424	#endif
	425
	426	#ifndef MTDIDS_DEFAULT
	427	# define MTDIDS_DEFAULT "nand0=fsl_elbc_nand"
	428	#endif /* MTDIDS_DEFAULT */
	429
	430	#ifndef MTDPARTS_DEFAULT
	431	# define MTDPARTS_DEFAULT "mtdparts=" \
	432	"fsl_elbc_nand:" \
	433	"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
	434	#endif /* MTDPARTS_DEFAULT */
	435
	436	/* architecture specific default bootargs */
	437	#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
	438
	439	/* FIXME: FDT_ADDR is unspecified */
	440	#define CONFIG_KM_DEF_ENV_CPU \
	441	"boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
	442	"cramfsloadfdt=" \
	443	"cramfsload ${fdt_addr_r} " \
	444	"fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
	445	"fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
	446	"u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \
	447	"update=" \
	448	"sf probe 0;sf erase 0 +${filesize};" \
	449	"sf write ${load_addr_r} 0 ${filesize};\0" \
b1c2a7ae	450	"set_fdthigh=true\0" \
877bfe37 VL	451	""
	452
	453	#define CONFIG_HW_ENV_SETTINGS \
	454	"hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \
	455	"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
	456	"usb_dr_mode=host\0"
	457
	458	#define CONFIG_KM_NEW_ENV \
	459	"newenv=sf probe 0;" \
	460	"sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
	461	__stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
	462
	463	/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
	464	#ifndef CONFIG_KM_DEF_ARCH
	465	#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
	466	#endif
	467
	468	#define CONFIG_EXTRA_ENV_SETTINGS \
	469	CONFIG_KM_DEF_ENV \
	470	CONFIG_KM_DEF_ARCH \
	471	CONFIG_KM_NEW_ENV \
	472	CONFIG_HW_ENV_SETTINGS \
	473	"EEprom_ivm=pca9547:70:9\0" \
	474	""
	475
	476	#endif /* _CONFIG_KMP204X_H */