[people/ms/u-boot.git] / include / configs / ls2080ardb.h

/*
 * Copyright 2015 Freescale Semiconductor
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __LS2_RDB_H
#define __LS2_RDB_H

#include "ls2080a_common.h"

#undef CONFIG_CONS_INDEX
#define CONFIG_CONS_INDEX       2

#define I2C_MUX_CH_VOL_MONITOR		0xa
#define I2C_VOL_MONITOR_ADDR		0x38
#define CONFIG_VOL_MONITOR_IR36021_READ
#define CONFIG_VOL_MONITOR_IR36021_SET

#define CONFIG_VID_FLS_ENV		"ls2080ardb_vdd_mv"
#ifndef CONFIG_SPL_BUILD
#define CONFIG_VID
#endif
/* step the IR regulator in 5mV increments */
#define IR_VDD_STEP_DOWN		5
#define IR_VDD_STEP_UP			5
/* The lowest and highest voltage allowed for LS2080ARDB */
#define VDD_MV_MIN			819
#define VDD_MV_MAX			1212

#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
#endif

#define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
#define CONFIG_DDR_CLK_FREQ		133333333
#define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)

#define CONFIG_DDR_SPD
#define CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
#define SPD_EEPROM_ADDRESS1	0x51
#define SPD_EEPROM_ADDRESS2	0x52
#define SPD_EEPROM_ADDRESS3	0x53
#define SPD_EEPROM_ADDRESS4	0x54
#define SPD_EEPROM_ADDRESS5	0x55
#define SPD_EEPROM_ADDRESS6	0x56	/* dummy address */
#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
#define CONFIG_SYS_SPD_BUS_NUM	0	/* SPD on I2C bus 0 */
#define CONFIG_DIMM_SLOTS_PER_CTLR		2
#define CONFIG_CHIP_SELECTS_PER_CTRL		4
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR	1
#endif
#define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */

/* SATA */
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SCSI
#define CONFIG_DOS_PARTITION

#define CONFIG_SYS_SATA1			AHCI_BASE_ADDR1
#define CONFIG_SYS_SATA2			AHCI_BASE_ADDR2

#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
#define CONFIG_SYS_SCSI_MAX_LUN			1
#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
						CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_PARTITION_UUIDS
#define CONFIG_EFI_PARTITION
#define CONFIG_CMD_GPT

/* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */

#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
#define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)

#define CONFIG_SYS_NOR0_CSPR					\
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
	CSPR_PORT_SIZE_16					| \
	CSPR_MSEL_NOR						| \
	CSPR_V)
#define CONFIG_SYS_NOR0_CSPR_EARLY				\
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
	CSPR_PORT_SIZE_16					| \
	CSPR_MSEL_NOR						| \
	CSPR_V)
#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
				FTIM0_NOR_TEADC(0x5) | \
				FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
				FTIM1_NOR_TRAD_NOR(0x1a) |\
				FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
				FTIM2_NOR_TCH(0x4) | \
				FTIM2_NOR_TWPH(0x0E) | \
				FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3	0x04000000
#define CONFIG_SYS_IFC_CCR	0x01000000

#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
					 CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif

#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_MAX_ECCPOS	256
#define CONFIG_SYS_NAND_MAX_OOBFREE	2

#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
				| CSPR_V)
#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)

#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
				| CSOR_NAND_PB(128))	/* Pages Per Block 128*/

#define CONFIG_SYS_NAND_ONFI_DETECTION

/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x0e) | \
					FTIM0_NAND_TWP(0x30)   | \
					FTIM0_NAND_TWCHT(0x0e) | \
					FTIM0_NAND_TWH(0x14))
#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x64) | \
					FTIM1_NAND_TWBE(0xab)  | \
					FTIM1_NAND_TRR(0x1c)   | \
					FTIM1_NAND_TRP(0x30))
#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x1e) | \
					FTIM2_NAND_TREH(0x14) | \
					FTIM2_NAND_TWHRE(0x3c))
#define CONFIG_SYS_NAND_FTIM3		0x0

#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND

#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)

#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
#define QIXIS_LBMAP_SWITCH		0x06
#define QIXIS_LBMAP_MASK		0x0f
#define QIXIS_LBMAP_SHIFT		0
#define QIXIS_LBMAP_DFLTBANK		0x00
#define QIXIS_LBMAP_ALTBANK		0x04
#define QIXIS_LBMAP_NAND		0x09
#define QIXIS_RST_CTL_RESET		0x31
#define QIXIS_RST_CTL_RESET_EN		0x30
#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
#define QIXIS_RCW_SRC_NAND		0x119
#define	QIXIS_RST_FORCE_MEM		0x01

#define CONFIG_SYS_CSPR3_EXT	(0x0)
#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
				| CSPR_PORT_SIZE_8 \
				| CSPR_MSEL_GPCM \
				| CSPR_V)
#define CONFIG_SYS_CSPR3_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 \
				| CSPR_MSEL_GPCM \
				| CSPR_V)

#define CONFIG_SYS_AMASK3	IFC_AMASK(64*1024)
#define CONFIG_SYS_CSOR3	CSOR_GPCM_ADM_SHIFT(12)
/* QIXIS Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
					FTIM0_GPCM_TEADC(0x0e) | \
					FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
					FTIM1_GPCM_TRAD(0x3f))
#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
					FTIM2_GPCM_TCH(0xf) | \
					FTIM2_GPCM_TWP(0x3E))
#define CONFIG_SYS_CS3_FTIM3		0x0

#if defined(CONFIG_SPL) && defined(CONFIG_NAND)
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR2_FINAL		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3

#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET		(2048 * 1024)
#define CONFIG_ENV_SECT_SIZE		0x20000
#define CONFIG_ENV_SIZE			0x2000
#define CONFIG_SPL_PAD_TO		0x80000
#define CONFIG_SYS_NAND_U_BOOT_OFFS	(1024 * 1024)
#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 * 1024)
#else
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3

#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
#define CONFIG_ENV_SECT_SIZE		0x20000
#define CONFIG_ENV_SIZE			0x2000
#endif

/* Debug Server firmware */
#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR	0x580D00000ULL

#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000

/*
 * I2C
 */
#define I2C_MUX_PCA_ADDR		0x75
#define I2C_MUX_PCA_ADDR_PRI		0x75 /* Primary Mux*/

/* I2C bus multiplexer */
#define I2C_MUX_CH_DEFAULT      0x8

/* SPI */
#ifdef CONFIG_FSL_DSPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SPI_FLASH_STMICRO
#endif

/*
 * RTC configuration
 */
#define RTC
#define CONFIG_RTC_DS3231               1
#define CONFIG_SYS_I2C_RTC_ADDR         0x68
#define CONFIG_CMD_DATE

/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM	0
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

#define CONFIG_FSL_MEMAC

#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#endif

/*  MMC  */
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#define CONFIG_GENERIC_MMC
#define CONFIG_DOS_PARTITION
#endif

#define CONFIG_MISC_INIT_R

/*
 * USB
 */
#define CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_XHCI_FSL
#define CONFIG_USB_MAX_CONTROLLER_COUNT         2
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2

#undef CONFIG_CMDLINE_EDITING
#include <config_distro_defaults.h>

#define BOOT_TARGET_DEVICES(func) \
	func(USB, usb, 0) \
	func(MMC, mmc, 0) \
	func(SCSI, scsi, 0) \
	func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>

/* Initial environment variables */
#undef CONFIG_EXTRA_ENV_SETTINGS
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
	"scriptaddr=0x80800000\0"		\
	"kernel_addr_r=0x81000000\0"		\
	"pxefile_addr_r=0x81000000\0"		\
	"fdt_addr_r=0x88000000\0"		\
	"ramdisk_addr_r=0x89000000\0"		\
	"loadaddr=0x80100000\0"			\
	"kernel_addr=0x100000\0"		\
	"ramdisk_addr=0x800000\0"		\
	"ramdisk_size=0x2000000\0"		\
	"fdt_high=0xa0000000\0"			\
	"initrd_high=0xffffffffffffffff\0"	\
	"kernel_start=0x581100000\0"		\
	"kernel_load=0xa0000000\0"		\
	"kernel_size=0x2800000\0"		\
	"fdtfile=fsl-ls2080a-rdb.dtb\0"		\
	"mcinitcmd=esbc_validate 0x580c80000;"  \
	"esbc_validate 0x580cc0000;"            \
	"fsl_mc start mc 0x580300000"           \
	" 0x580800000 \0"                       \
	BOOTENV
#else
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
	"scriptaddr=0x80800000\0"		\
	"kernel_addr_r=0x81000000\0"		\
	"pxefile_addr_r=0x81000000\0"		\
	"fdt_addr_r=0x88000000\0"		\
	"ramdisk_addr_r=0x89000000\0"		\
	"loadaddr=0x80100000\0"			\
	"kernel_addr=0x100000\0"		\
	"ramdisk_addr=0x800000\0"		\
	"ramdisk_size=0x2000000\0"		\
	"fdt_high=0xa0000000\0"			\
	"initrd_high=0xffffffffffffffff\0"	\
	"kernel_start=0x581100000\0"		\
	"kernel_load=0xa0000000\0"		\
	"kernel_size=0x2800000\0"		\
	"fdtfile=fsl-ls2080a-rdb.dtb\0"		\
	"mcinitcmd=fsl_mc start mc 0x580300000" \
	" 0x580800000 \0"                       \
	BOOTENV
#endif


#undef CONFIG_BOOTARGS
#define CONFIG_BOOTARGS		"console=ttyS1,115200 root=/dev/ram0 " \
				"earlycon=uart8250,mmio,0x21c0600 " \
				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
				" hugepagesz=2m hugepages=256"

#undef CONFIG_BOOTCOMMAND
/* Try to boot an on-NOR kernel first, then do normal distro boot */
#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \
			   " && cp.b $kernel_start $kernel_load $kernel_size" \
			   " && bootm $kernel_load" \
			   " || run distro_bootcmd"

/* MAC/PHY configuration */
#ifdef CONFIG_FSL_MC_ENET
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_AQUANTIA
#define CONFIG_PHY_CORTINA
#define CONFIG_PHYLIB
#define	CONFIG_SYS_CORTINA_FW_IN_NOR
#define CONFIG_CORTINA_FW_ADDR		0x581000000
#define CONFIG_CORTINA_FW_LENGTH	0x40000

#define CORTINA_PHY_ADDR1	0x10
#define CORTINA_PHY_ADDR2	0x11
#define CORTINA_PHY_ADDR3	0x12
#define CORTINA_PHY_ADDR4	0x13
#define AQ_PHY_ADDR1		0x00
#define AQ_PHY_ADDR2		0x01
#define AQ_PHY_ADDR3		0x02
#define AQ_PHY_ADDR4		0x03
#define AQR405_IRQ_MASK		0x36

#define CONFIG_MII
#define CONFIG_ETHPRIME		"DPMAC1@xgmii"
#define CONFIG_PHY_GIGE
#define CONFIG_PHY_AQUANTIA
#endif

#include <asm/fsl_secure_boot.h>

#endif /* __LS2_RDB_H */
Commit	Line	Data
e2b65ea9 YS	1	/*
	2	* Copyright 2015 Freescale Semiconductor
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	#ifndef __LS2_RDB_H
	8	#define __LS2_RDB_H
	9
44937214	10	#include "ls2080a_common.h"
e2b65ea9 YS	11
	12	#undef CONFIG_CONS_INDEX
	13	#define CONFIG_CONS_INDEX 2
	14
ed2530d0 RH	15	#define I2C_MUX_CH_VOL_MONITOR 0xa
	16	#define I2C_VOL_MONITOR_ADDR 0x38
	17	#define CONFIG_VOL_MONITOR_IR36021_READ
	18	#define CONFIG_VOL_MONITOR_IR36021_SET
	19
	20	#define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv"
	21	#ifndef CONFIG_SPL_BUILD
	22	#define CONFIG_VID
	23	#endif
	24	/* step the IR regulator in 5mV increments */
	25	#define IR_VDD_STEP_DOWN 5
	26	#define IR_VDD_STEP_UP 5
	27	/* The lowest and highest voltage allowed for LS2080ARDB */
	28	#define VDD_MV_MIN 819
	29	#define VDD_MV_MAX 1212
	30
e2b65ea9 YS	31	#ifndef __ASSEMBLY__
	32	unsigned long get_board_sys_clk(void);
	33	#endif
	34
	35	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
	36	#define CONFIG_DDR_CLK_FREQ 133333333
	37	#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
	38
	39	#define CONFIG_DDR_SPD
	40	#define CONFIG_DDR_ECC
	41	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	42	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	43	#define SPD_EEPROM_ADDRESS1 0x51
	44	#define SPD_EEPROM_ADDRESS2 0x52
fc7b3855 YS	45	#define SPD_EEPROM_ADDRESS3 0x53
fc7b3855 YS	46	#define SPD_EEPROM_ADDRESS4 0x54
e2b65ea9 YS	47	#define SPD_EEPROM_ADDRESS5 0x55
	48	#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */
	49	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
	50	#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
	51	#define CONFIG_DIMM_SLOTS_PER_CTLR 2
	52	#define CONFIG_CHIP_SELECTS_PER_CTRL 4
44937214	53	#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
e2b65ea9	54	#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
44937214	55	#endif
e2b65ea9 YS	56	#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
e2b65ea9 YS	57
989c5f0a TY	58	/* SATA */
	59	#define CONFIG_LIBATA
	60	#define CONFIG_SCSI_AHCI
	61	#define CONFIG_SCSI_AHCI_PLAT
c649e3c9	62	#define CONFIG_SCSI
989c5f0a	63	#define CONFIG_DOS_PARTITION
989c5f0a TY	64
	65	#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
	66	#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
	67
	68	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
	69	#define CONFIG_SYS_SCSI_MAX_LUN 1
	70	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	71	CONFIG_SYS_SCSI_MAX_LUN)
9e0bb4c1 PK	72	#define CONFIG_PARTITION_UUIDS
	73	#define CONFIG_EFI_PARTITION
	74	#define CONFIG_CMD_GPT
989c5f0a	75
e2b65ea9 YS	76	/* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
	77
	78	#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
	79	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(12810241024)
	80	#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(6410241024)
	81
	82	#define CONFIG_SYS_NOR0_CSPR \
	83	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
	84	CSPR_PORT_SIZE_16 \| \
	85	CSPR_MSEL_NOR \| \
	86	CSPR_V)
	87	#define CONFIG_SYS_NOR0_CSPR_EARLY \
	88	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) \| \
	89	CSPR_PORT_SIZE_16 \| \
	90	CSPR_MSEL_NOR \| \
	91	CSPR_V)
	92	#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
	93	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
	94	FTIM0_NOR_TEADC(0x5) \| \
	95	FTIM0_NOR_TEAHC(0x5))
	96	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
	97	FTIM1_NOR_TRAD_NOR(0x1a) \|\
	98	FTIM1_NOR_TSEQRAD_NOR(0x13))
	99	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
	100	FTIM2_NOR_TCH(0x4) \| \
	101	FTIM2_NOR_TWPH(0x0E) \| \
	102	FTIM2_NOR_TWP(0x1c))
	103	#define CONFIG_SYS_NOR_FTIM3 0x04000000
	104	#define CONFIG_SYS_IFC_CCR 0x01000000
	105
	106	#ifndef CONFIG_SYS_NO_FLASH
	107	#define CONFIG_FLASH_CFI_DRIVER
	108	#define CONFIG_SYS_FLASH_CFI
	109	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	110	#define CONFIG_SYS_FLASH_QUIET_TEST
	111	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
	112
	113	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	114	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	115	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	116	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	117
	118	#define CONFIG_SYS_FLASH_EMPTY_INFO
	119	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
	120	CONFIG_SYS_FLASH_BASE + 0x40000000}
	121	#endif
	122
	123	#define CONFIG_NAND_FSL_IFC
	124	#define CONFIG_SYS_NAND_MAX_ECCPOS 256
	125	#define CONFIG_SYS_NAND_MAX_OOBFREE 2
	126
e2b65ea9 YS	127	#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
	128	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	129	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	130	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	131	\| CSPR_V)
	132	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
	133
	134	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	135	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	136	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	137	\| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
	138	\| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
	139	\| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
	140	\| CSOR_NAND_PB(128)) /* Pages Per Block 128*/
	141
	142	#define CONFIG_SYS_NAND_ONFI_DETECTION
	143
	144	/* ONFI NAND Flash mode0 Timing Params */
	145	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) \| \
	146	FTIM0_NAND_TWP(0x30) \| \
	147	FTIM0_NAND_TWCHT(0x0e) \| \
	148	FTIM0_NAND_TWH(0x14))
	149	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) \| \
	150	FTIM1_NAND_TWBE(0xab) \| \
	151	FTIM1_NAND_TRR(0x1c) \| \
	152	FTIM1_NAND_TRP(0x30))
	153	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) \| \
	154	FTIM2_NAND_TREH(0x14) \| \
	155	FTIM2_NAND_TWHRE(0x3c))
	156	#define CONFIG_SYS_NAND_FTIM3 0x0
	157
	158	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	159	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	160	#define CONFIG_MTD_NAND_VERIFY_WRITE
	161	#define CONFIG_CMD_NAND
	162
	163	#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
	164
	165	#define CONFIG_FSL_QIXIS /* use common QIXIS code */
	166	#define QIXIS_LBMAP_SWITCH 0x06
	167	#define QIXIS_LBMAP_MASK 0x0f
	168	#define QIXIS_LBMAP_SHIFT 0
	169	#define QIXIS_LBMAP_DFLTBANK 0x00
	170	#define QIXIS_LBMAP_ALTBANK 0x04
32eda7cc	171	#define QIXIS_LBMAP_NAND 0x09
e2b65ea9 YS	172	#define QIXIS_RST_CTL_RESET 0x31
	173	#define QIXIS_RST_CTL_RESET_EN 0x30
	174	#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
	175	#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
	176	#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
32eda7cc	177	#define QIXIS_RCW_SRC_NAND 0x119
e2b65ea9 YS	178	#define QIXIS_RST_FORCE_MEM 0x01
	179
	180	#define CONFIG_SYS_CSPR3_EXT (0x0)
	181	#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
	182	\| CSPR_PORT_SIZE_8 \
	183	\| CSPR_MSEL_GPCM \
	184	\| CSPR_V)
	185	#define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
	186	\| CSPR_PORT_SIZE_8 \
	187	\| CSPR_MSEL_GPCM \
	188	\| CSPR_V)
	189
	190	#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024)
	191	#define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12)
	192	/* QIXIS Timing parameters for IFC CS3 */
	193	#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	194	FTIM0_GPCM_TEADC(0x0e) \| \
	195	FTIM0_GPCM_TEAHC(0x0e))
	196	#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	197	FTIM1_GPCM_TRAD(0x3f))
	198	#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) \| \
	199	FTIM2_GPCM_TCH(0xf) \| \
	200	FTIM2_GPCM_TWP(0x3E))
	201	#define CONFIG_SYS_CS3_FTIM3 0x0
	202
32eda7cc SW	203	#if defined(CONFIG_SPL) && defined(CONFIG_NAND)
	204	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
	205	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY
	206	#define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR
	207	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
	208	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
	209	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
	210	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
	211	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
	212	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
	213	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
	214	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
	215	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
	216	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
	217	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
	218	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
	219	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
	220	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
	221
	222	#define CONFIG_ENV_IS_IN_NAND
	223	#define CONFIG_ENV_OFFSET (2048 * 1024)
	224	#define CONFIG_ENV_SECT_SIZE 0x20000
	225	#define CONFIG_ENV_SIZE 0x2000
	226	#define CONFIG_SPL_PAD_TO 0x80000
	227	#define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024)
	228	#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024)
	229	#else
e2b65ea9 YS	230	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
	231	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
	232	#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
	233	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
	234	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
	235	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
	236	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
	237	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
	238	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
	239	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
	240	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
	241	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
	242	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
	243	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
	244	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
	245	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
	246	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
	247
32eda7cc SW	248	#define CONFIG_ENV_IS_IN_FLASH
	249	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
	250	#define CONFIG_ENV_SECT_SIZE 0x20000
	251	#define CONFIG_ENV_SIZE 0x2000
	252	#endif
	253
e2b65ea9 YS	254	/* Debug Server firmware */
	255	#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
	256	#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
	257
e2b65ea9 YS	258	#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
	259
	260	/*
	261	* I2C
	262	*/
4012350d PK	263	#define I2C_MUX_PCA_ADDR 0x75
4012350d PK	264	#define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/
e2b65ea9 YS	265
	266	/* I2C bus multiplexer */
	267	#define I2C_MUX_CH_DEFAULT 0x8
	268
0c42a8de HW	269	/* SPI */
0c42a8de HW	270	#ifdef CONFIG_FSL_DSPI
0c42a8de	271	#define CONFIG_SPI_FLASH
0c42a8de	272	#define CONFIG_SPI_FLASH_BAR
21640db5	273	#define CONFIG_SPI_FLASH_STMICRO
0c42a8de HW	274	#endif
0c42a8de HW	275
e2b65ea9 YS	276	/*
	277	* RTC configuration
	278	*/
	279	#define RTC
	280	#define CONFIG_RTC_DS3231 1
	281	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
6581440c	282	#define CONFIG_CMD_DATE
e2b65ea9 YS	283
	284	/* EEPROM */
	285	#define CONFIG_ID_EEPROM
	286	#define CONFIG_CMD_EEPROM
	287	#define CONFIG_SYS_I2C_EEPROM_NXID
	288	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	289	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	290	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	291	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	292	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
	293
e2b65ea9	294	#define CONFIG_FSL_MEMAC
e2b65ea9 YS	295
e2b65ea9 YS	296	#ifdef CONFIG_PCI
e2b65ea9 YS	297	#define CONFIG_PCI_SCAN_SHOW
e2b65ea9 YS	298	#define CONFIG_CMD_PCI
e2b65ea9 YS	299	#endif
e2b65ea9 YS	300
8b06460e	301	/* MMC */
8b06460e	302	#ifdef CONFIG_MMC
8b06460e YL	303	#define CONFIG_FSL_ESDHC
	304	#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
	305	#define CONFIG_GENERIC_MMC
8b06460e YL	306	#define CONFIG_DOS_PARTITION
8b06460e YL	307	#endif
e2b65ea9	308
5a4d744c YL	309	#define CONFIG_MISC_INIT_R
5a4d744c YL	310
e16b604e NB	311	/*
	312	* USB
	313	*/
	314	#define CONFIG_HAS_FSL_XHCI_USB
e16b604e	315	#define CONFIG_USB_XHCI_FSL
e16b604e NB	316	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
e16b604e NB	317	#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
e16b604e	318
b99ebaf9 AG	319	#undef CONFIG_CMDLINE_EDITING
	320	#include <config_distro_defaults.h>
	321
	322	#define BOOT_TARGET_DEVICES(func) \
	323	func(USB, usb, 0) \
	324	func(MMC, mmc, 0) \
	325	func(SCSI, scsi, 0) \
	326	func(DHCP, dhcp, na)
	327	#include <config_distro_bootcmd.h>
	328
e2b65ea9 YS	329	/* Initial environment variables */
e2b65ea9 YS	330	#undef CONFIG_EXTRA_ENV_SETTINGS
9ed44787	331	#ifdef CONFIG_SECURE_BOOT
e2b65ea9 YS	332	#define CONFIG_EXTRA_ENV_SETTINGS \
e2b65ea9 YS	333	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
b99ebaf9 AG	334	"scriptaddr=0x80800000\0" \
	335	"kernel_addr_r=0x81000000\0" \
	336	"pxefile_addr_r=0x81000000\0" \
	337	"fdt_addr_r=0x88000000\0" \
	338	"ramdisk_addr_r=0x89000000\0" \
e2b65ea9 YS	339	"loadaddr=0x80100000\0" \
	340	"kernel_addr=0x100000\0" \
	341	"ramdisk_addr=0x800000\0" \
	342	"ramdisk_size=0x2000000\0" \
	343	"fdt_high=0xa0000000\0" \
	344	"initrd_high=0xffffffffffffffff\0" \
	345	"kernel_start=0x581100000\0" \
	346	"kernel_load=0xa0000000\0" \
16ed8560	347	"kernel_size=0x2800000\0" \
b99ebaf9	348	"fdtfile=fsl-ls2080a-rdb.dtb\0" \
9ed44787 UA	349	"mcinitcmd=esbc_validate 0x580c80000;" \
	350	"esbc_validate 0x580cc0000;" \
	351	"fsl_mc start mc 0x580300000" \
	352	" 0x580800000 \0" \
b99ebaf9	353	BOOTENV
9ed44787 UA	354	#else
	355	#define CONFIG_EXTRA_ENV_SETTINGS \
	356	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	357	"scriptaddr=0x80800000\0" \
	358	"kernel_addr_r=0x81000000\0" \
	359	"pxefile_addr_r=0x81000000\0" \
	360	"fdt_addr_r=0x88000000\0" \
	361	"ramdisk_addr_r=0x89000000\0" \
	362	"loadaddr=0x80100000\0" \
	363	"kernel_addr=0x100000\0" \
	364	"ramdisk_addr=0x800000\0" \
	365	"ramdisk_size=0x2000000\0" \
	366	"fdt_high=0xa0000000\0" \
	367	"initrd_high=0xffffffffffffffff\0" \
	368	"kernel_start=0x581100000\0" \
	369	"kernel_load=0xa0000000\0" \
	370	"kernel_size=0x2800000\0" \
	371	"fdtfile=fsl-ls2080a-rdb.dtb\0" \
	372	"mcinitcmd=fsl_mc start mc 0x580300000" \
	373	" 0x580800000 \0" \
	374	BOOTENV
	375	#endif
	376
e2b65ea9	377
56cd0760 PK	378	#undef CONFIG_BOOTARGS
56cd0760 PK	379	#define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \
ed77b704	380	"earlycon=uart8250,mmio,0x21c0600 " \
56cd0760	381	"ramdisk_size=0x2000000 default_hugepagesz=2m" \
9e71bb9c	382	" hugepagesz=2m hugepages=256"
56cd0760	383
b99ebaf9 AG	384	#undef CONFIG_BOOTCOMMAND
	385	/* Try to boot an on-NOR kernel first, then do normal distro boot */
	386	#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \
	387	" && cp.b $kernel_start $kernel_load $kernel_size" \
	388	" && bootm $kernel_load" \
	389	" \|\| run distro_bootcmd"
	390
3484d953 PK	391	/* MAC/PHY configuration */
	392	#ifdef CONFIG_FSL_MC_ENET
	393	#define CONFIG_PHYLIB_10G
c69384e1	394	#define CONFIG_PHY_AQUANTIA
3484d953 PK	395	#define CONFIG_PHY_CORTINA
	396	#define CONFIG_PHYLIB
	397	#define CONFIG_SYS_CORTINA_FW_IN_NOR
	398	#define CONFIG_CORTINA_FW_ADDR 0x581000000
	399	#define CONFIG_CORTINA_FW_LENGTH 0x40000
	400
	401	#define CORTINA_PHY_ADDR1 0x10
	402	#define CORTINA_PHY_ADDR2 0x11
	403	#define CORTINA_PHY_ADDR3 0x12
	404	#define CORTINA_PHY_ADDR4 0x13
	405	#define AQ_PHY_ADDR1 0x00
	406	#define AQ_PHY_ADDR2 0x01
	407	#define AQ_PHY_ADDR3 0x02
	408	#define AQ_PHY_ADDR4 0x03
abc7d0f7	409	#define AQR405_IRQ_MASK 0x36
3484d953 PK	410
3484d953 PK	411	#define CONFIG_MII
7ad9cc96	412	#define CONFIG_ETHPRIME "DPMAC1@xgmii"
3484d953	413	#define CONFIG_PHY_GIGE
95279315	414	#define CONFIG_PHY_AQUANTIA
3484d953 PK	415	#endif
3484d953 PK	416
fcfdb6d5 SJ	417	#include <asm/fsl_secure_boot.h>
fcfdb6d5 SJ	418
e2b65ea9	419	#endif /* __LS2_RDB_H */