[people/ms/u-boot.git] / include / configs / ls2080ardb.h

/*
 * Copyright 2015 Freescale Semiconductor
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __LS2_RDB_H
#define __LS2_RDB_H

#include "ls2080a_common.h"

#undef CONFIG_CONS_INDEX
#define CONFIG_CONS_INDEX       2

#define I2C_MUX_CH_VOL_MONITOR		0xa
#define I2C_VOL_MONITOR_ADDR		0x38
#define CONFIG_VOL_MONITOR_IR36021_READ
#define CONFIG_VOL_MONITOR_IR36021_SET

#define CONFIG_VID_FLS_ENV		"ls2080ardb_vdd_mv"
#ifndef CONFIG_SPL_BUILD
#define CONFIG_VID
#endif
/* step the IR regulator in 5mV increments */
#define IR_VDD_STEP_DOWN		5
#define IR_VDD_STEP_UP			5
/* The lowest and highest voltage allowed for LS2080ARDB */
#define VDD_MV_MIN			819
#define VDD_MV_MAX			1212

#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
#endif

#define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
#define CONFIG_DDR_CLK_FREQ		133333333
#define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)

#define CONFIG_DDR_SPD
#define CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
#define SPD_EEPROM_ADDRESS1	0x51
#define SPD_EEPROM_ADDRESS2	0x52
#define SPD_EEPROM_ADDRESS3	0x53
#define SPD_EEPROM_ADDRESS4	0x54
#define SPD_EEPROM_ADDRESS5	0x55
#define SPD_EEPROM_ADDRESS6	0x56	/* dummy address */
#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
#define CONFIG_SYS_SPD_BUS_NUM	0	/* SPD on I2C bus 0 */
#define CONFIG_DIMM_SLOTS_PER_CTLR		2
#define CONFIG_CHIP_SELECTS_PER_CTRL		4
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR	1
#endif
#define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */

/* SATA */
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SCSI

#define CONFIG_SYS_SATA1			AHCI_BASE_ADDR1
#define CONFIG_SYS_SATA2			AHCI_BASE_ADDR2

#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
#define CONFIG_SYS_SCSI_MAX_LUN			1
#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
						CONFIG_SYS_SCSI_MAX_LUN)

/* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */

#define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
#define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)

#define CONFIG_SYS_NOR0_CSPR					\
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
	CSPR_PORT_SIZE_16					| \
	CSPR_MSEL_NOR						| \
	CSPR_V)
#define CONFIG_SYS_NOR0_CSPR_EARLY				\
	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
	CSPR_PORT_SIZE_16					| \
	CSPR_MSEL_NOR						| \
	CSPR_V)
#define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
				FTIM0_NOR_TEADC(0x5) | \
				FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
				FTIM1_NOR_TRAD_NOR(0x1a) |\
				FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
				FTIM2_NOR_TCH(0x4) | \
				FTIM2_NOR_TWPH(0x0E) | \
				FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3	0x04000000
#define CONFIG_SYS_IFC_CCR	0x01000000

#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
					 CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif

#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_MAX_ECCPOS	256
#define CONFIG_SYS_NAND_MAX_OOBFREE	2

#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
				| CSPR_V)
#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)

#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
				| CSOR_NAND_PB(128))	/* Pages Per Block 128*/

#define CONFIG_SYS_NAND_ONFI_DETECTION

/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x0e) | \
					FTIM0_NAND_TWP(0x30)   | \
					FTIM0_NAND_TWCHT(0x0e) | \
					FTIM0_NAND_TWH(0x14))
#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x64) | \
					FTIM1_NAND_TWBE(0xab)  | \
					FTIM1_NAND_TRR(0x1c)   | \
					FTIM1_NAND_TRP(0x30))
#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x1e) | \
					FTIM2_NAND_TREH(0x14) | \
					FTIM2_NAND_TWHRE(0x3c))
#define CONFIG_SYS_NAND_FTIM3		0x0

#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND

#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)

#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
#define QIXIS_LBMAP_SWITCH		0x06
#define QIXIS_LBMAP_MASK		0x0f
#define QIXIS_LBMAP_SHIFT		0
#define QIXIS_LBMAP_DFLTBANK		0x00
#define QIXIS_LBMAP_ALTBANK		0x04
#define QIXIS_LBMAP_NAND		0x09
#define QIXIS_RST_CTL_RESET		0x31
#define QIXIS_RST_CTL_RESET_EN		0x30
#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
#define QIXIS_RCW_SRC_NAND		0x119
#define	QIXIS_RST_FORCE_MEM		0x01

#define CONFIG_SYS_CSPR3_EXT	(0x0)
#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
				| CSPR_PORT_SIZE_8 \
				| CSPR_MSEL_GPCM \
				| CSPR_V)
#define CONFIG_SYS_CSPR3_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
				| CSPR_PORT_SIZE_8 \
				| CSPR_MSEL_GPCM \
				| CSPR_V)

#define CONFIG_SYS_AMASK3	IFC_AMASK(64*1024)
#define CONFIG_SYS_CSOR3	CSOR_GPCM_ADM_SHIFT(12)
/* QIXIS Timing parameters for IFC CS3 */
#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
					FTIM0_GPCM_TEADC(0x0e) | \
					FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
					FTIM1_GPCM_TRAD(0x3f))
#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
					FTIM2_GPCM_TCH(0xf) | \
					FTIM2_GPCM_TWP(0x3E))
#define CONFIG_SYS_CS3_FTIM3		0x0

#if defined(CONFIG_SPL) && defined(CONFIG_NAND)
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR2_FINAL		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3

#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET		(2048 * 1024)
#define CONFIG_ENV_SECT_SIZE		0x20000
#define CONFIG_ENV_SIZE			0x2000
#define CONFIG_SPL_PAD_TO		0x80000
#define CONFIG_SYS_NAND_U_BOOT_OFFS	(1024 * 1024)
#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 * 1024)
#else
#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3

#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
#define CONFIG_ENV_SECT_SIZE		0x20000
#define CONFIG_ENV_SIZE			0x2000
#endif

/* Debug Server firmware */
#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR	0x580D00000ULL

#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000

/*
 * I2C
 */
#define I2C_MUX_PCA_ADDR		0x75
#define I2C_MUX_PCA_ADDR_PRI		0x75 /* Primary Mux*/

/* I2C bus multiplexer */
#define I2C_MUX_CH_DEFAULT      0x8

/* SPI */
#ifdef CONFIG_FSL_DSPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SPI_FLASH_STMICRO
#endif

/*
 * RTC configuration
 */
#define RTC
#define CONFIG_RTC_DS3231               1
#define CONFIG_SYS_I2C_RTC_ADDR         0x68
#define CONFIG_CMD_DATE

/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM	0
#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

#define CONFIG_FSL_MEMAC

#ifdef CONFIG_PCI
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#endif

/*  MMC  */
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif

#define CONFIG_MISC_INIT_R

/*
 * USB
 */
#define CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_XHCI_FSL
#define CONFIG_USB_MAX_CONTROLLER_COUNT         2
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2

#undef CONFIG_CMDLINE_EDITING
#include <config_distro_defaults.h>

#define BOOT_TARGET_DEVICES(func) \
	func(USB, usb, 0) \
	func(MMC, mmc, 0) \
	func(SCSI, scsi, 0) \
	func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>

/* Initial environment variables */
#undef CONFIG_EXTRA_ENV_SETTINGS
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
	"scriptaddr=0x80800000\0"		\
	"kernel_addr_r=0x81000000\0"		\
	"pxefile_addr_r=0x81000000\0"		\
	"fdt_addr_r=0x88000000\0"		\
	"ramdisk_addr_r=0x89000000\0"		\
	"loadaddr=0x80100000\0"			\
	"kernel_addr=0x100000\0"		\
	"ramdisk_addr=0x800000\0"		\
	"ramdisk_size=0x2000000\0"		\
	"fdt_high=0xa0000000\0"			\
	"initrd_high=0xffffffffffffffff\0"	\
	"kernel_start=0x581100000\0"		\
	"kernel_load=0xa0000000\0"		\
	"kernel_size=0x2800000\0"		\
	"fdtfile=fsl-ls2080a-rdb.dtb\0"		\
	"mcinitcmd=esbc_validate 0x580c80000;"  \
	"esbc_validate 0x580cc0000;"            \
	"fsl_mc start mc 0x580300000"           \
	" 0x580800000 \0"                       \
	BOOTENV
#else
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
	"scriptaddr=0x80800000\0"		\
	"kernel_addr_r=0x81000000\0"		\
	"pxefile_addr_r=0x81000000\0"		\
	"fdt_addr_r=0x88000000\0"		\
	"ramdisk_addr_r=0x89000000\0"		\
	"loadaddr=0x80100000\0"			\
	"kernel_addr=0x100000\0"		\
	"ramdisk_addr=0x800000\0"		\
	"ramdisk_size=0x2000000\0"		\
	"fdt_high=0xa0000000\0"			\
	"initrd_high=0xffffffffffffffff\0"	\
	"kernel_start=0x581100000\0"		\
	"kernel_load=0xa0000000\0"		\
	"kernel_size=0x2800000\0"		\
	"fdtfile=fsl-ls2080a-rdb.dtb\0"		\
	"mcinitcmd=fsl_mc start mc 0x580300000" \
	" 0x580800000 \0"                       \
	BOOTENV
#endif


#undef CONFIG_BOOTARGS
#define CONFIG_BOOTARGS		"console=ttyS1,115200 root=/dev/ram0 " \
				"earlycon=uart8250,mmio,0x21c0600 " \
				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
				" hugepagesz=2m hugepages=256"

#undef CONFIG_BOOTCOMMAND
/* Try to boot an on-NOR kernel first, then do normal distro boot */
#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \
			   " && cp.b $kernel_start $kernel_load $kernel_size" \
			   " && bootm $kernel_load" \
			   " || run distro_bootcmd"

/* MAC/PHY configuration */
#ifdef CONFIG_FSL_MC_ENET
#define CONFIG_PHYLIB_10G
#define CONFIG_PHY_AQUANTIA
#define CONFIG_PHY_CORTINA
#define CONFIG_PHYLIB
#define	CONFIG_SYS_CORTINA_FW_IN_NOR
#define CONFIG_CORTINA_FW_ADDR		0x581000000
#define CONFIG_CORTINA_FW_LENGTH	0x40000

#define CORTINA_PHY_ADDR1	0x10
#define CORTINA_PHY_ADDR2	0x11
#define CORTINA_PHY_ADDR3	0x12
#define CORTINA_PHY_ADDR4	0x13
#define AQ_PHY_ADDR1		0x00
#define AQ_PHY_ADDR2		0x01
#define AQ_PHY_ADDR3		0x02
#define AQ_PHY_ADDR4		0x03
#define AQR405_IRQ_MASK		0x36

#define CONFIG_MII
#define CONFIG_ETHPRIME		"DPMAC1@xgmii"
#define CONFIG_PHY_GIGE
#define CONFIG_PHY_AQUANTIA
#endif

#include <asm/fsl_secure_boot.h>

#endif /* __LS2_RDB_H */
Commit	Line	Data
e2b65ea9 YS	1	/*
	2	* Copyright 2015 Freescale Semiconductor
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	#ifndef __LS2_RDB_H
	8	#define __LS2_RDB_H
	9
44937214	10	#include "ls2080a_common.h"
e2b65ea9 YS	11
	12	#undef CONFIG_CONS_INDEX
	13	#define CONFIG_CONS_INDEX 2
	14
ed2530d0 RH	15	#define I2C_MUX_CH_VOL_MONITOR 0xa
	16	#define I2C_VOL_MONITOR_ADDR 0x38
	17	#define CONFIG_VOL_MONITOR_IR36021_READ
	18	#define CONFIG_VOL_MONITOR_IR36021_SET
	19
	20	#define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv"
	21	#ifndef CONFIG_SPL_BUILD
	22	#define CONFIG_VID
	23	#endif
	24	/* step the IR regulator in 5mV increments */
	25	#define IR_VDD_STEP_DOWN 5
	26	#define IR_VDD_STEP_UP 5
	27	/* The lowest and highest voltage allowed for LS2080ARDB */
	28	#define VDD_MV_MIN 819
	29	#define VDD_MV_MAX 1212
	30
e2b65ea9 YS	31	#ifndef __ASSEMBLY__
	32	unsigned long get_board_sys_clk(void);
	33	#endif
	34
	35	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
	36	#define CONFIG_DDR_CLK_FREQ 133333333
	37	#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
	38
	39	#define CONFIG_DDR_SPD
	40	#define CONFIG_DDR_ECC
	41	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	42	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	43	#define SPD_EEPROM_ADDRESS1 0x51
	44	#define SPD_EEPROM_ADDRESS2 0x52
fc7b3855 YS	45	#define SPD_EEPROM_ADDRESS3 0x53
fc7b3855 YS	46	#define SPD_EEPROM_ADDRESS4 0x54
e2b65ea9 YS	47	#define SPD_EEPROM_ADDRESS5 0x55
	48	#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */
	49	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
	50	#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
	51	#define CONFIG_DIMM_SLOTS_PER_CTLR 2
	52	#define CONFIG_CHIP_SELECTS_PER_CTRL 4
44937214	53	#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
e2b65ea9	54	#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
44937214	55	#endif
e2b65ea9 YS	56	#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
e2b65ea9 YS	57
989c5f0a TY	58	/* SATA */
	59	#define CONFIG_LIBATA
	60	#define CONFIG_SCSI_AHCI
	61	#define CONFIG_SCSI_AHCI_PLAT
c649e3c9	62	#define CONFIG_SCSI
989c5f0a TY	63
	64	#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
	65	#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
	66
	67	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
	68	#define CONFIG_SYS_SCSI_MAX_LUN 1
	69	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	70	CONFIG_SYS_SCSI_MAX_LUN)
	71
e2b65ea9 YS	72	/* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
	73
	74	#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
	75	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(12810241024)
	76	#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(6410241024)
	77
	78	#define CONFIG_SYS_NOR0_CSPR \
	79	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
	80	CSPR_PORT_SIZE_16 \| \
	81	CSPR_MSEL_NOR \| \
	82	CSPR_V)
	83	#define CONFIG_SYS_NOR0_CSPR_EARLY \
	84	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) \| \
	85	CSPR_PORT_SIZE_16 \| \
	86	CSPR_MSEL_NOR \| \
	87	CSPR_V)
	88	#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
	89	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
	90	FTIM0_NOR_TEADC(0x5) \| \
	91	FTIM0_NOR_TEAHC(0x5))
	92	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
	93	FTIM1_NOR_TRAD_NOR(0x1a) \|\
	94	FTIM1_NOR_TSEQRAD_NOR(0x13))
	95	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
	96	FTIM2_NOR_TCH(0x4) \| \
	97	FTIM2_NOR_TWPH(0x0E) \| \
	98	FTIM2_NOR_TWP(0x1c))
	99	#define CONFIG_SYS_NOR_FTIM3 0x04000000
	100	#define CONFIG_SYS_IFC_CCR 0x01000000
	101
e856bdcf	102	#ifdef CONFIG_MTD_NOR_FLASH
e2b65ea9 YS	103	#define CONFIG_FLASH_CFI_DRIVER
	104	#define CONFIG_SYS_FLASH_CFI
	105	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	106	#define CONFIG_SYS_FLASH_QUIET_TEST
	107	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
	108
	109	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	110	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	111	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	112	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	113
	114	#define CONFIG_SYS_FLASH_EMPTY_INFO
	115	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
	116	CONFIG_SYS_FLASH_BASE + 0x40000000}
	117	#endif
	118
	119	#define CONFIG_NAND_FSL_IFC
	120	#define CONFIG_SYS_NAND_MAX_ECCPOS 256
	121	#define CONFIG_SYS_NAND_MAX_OOBFREE 2
	122
e2b65ea9 YS	123	#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
	124	#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	125	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	126	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	127	\| CSPR_V)
	128	#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
	129
	130	#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	131	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	132	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	133	\| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
	134	\| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
	135	\| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
	136	\| CSOR_NAND_PB(128)) /* Pages Per Block 128*/
	137
	138	#define CONFIG_SYS_NAND_ONFI_DETECTION
	139
	140	/* ONFI NAND Flash mode0 Timing Params */
	141	#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) \| \
	142	FTIM0_NAND_TWP(0x30) \| \
	143	FTIM0_NAND_TWCHT(0x0e) \| \
	144	FTIM0_NAND_TWH(0x14))
	145	#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) \| \
	146	FTIM1_NAND_TWBE(0xab) \| \
	147	FTIM1_NAND_TRR(0x1c) \| \
	148	FTIM1_NAND_TRP(0x30))
	149	#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) \| \
	150	FTIM2_NAND_TREH(0x14) \| \
	151	FTIM2_NAND_TWHRE(0x3c))
	152	#define CONFIG_SYS_NAND_FTIM3 0x0
	153
	154	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	155	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	156	#define CONFIG_MTD_NAND_VERIFY_WRITE
	157	#define CONFIG_CMD_NAND
	158
	159	#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
	160
	161	#define CONFIG_FSL_QIXIS /* use common QIXIS code */
	162	#define QIXIS_LBMAP_SWITCH 0x06
	163	#define QIXIS_LBMAP_MASK 0x0f
	164	#define QIXIS_LBMAP_SHIFT 0
	165	#define QIXIS_LBMAP_DFLTBANK 0x00
	166	#define QIXIS_LBMAP_ALTBANK 0x04
32eda7cc	167	#define QIXIS_LBMAP_NAND 0x09
e2b65ea9 YS	168	#define QIXIS_RST_CTL_RESET 0x31
	169	#define QIXIS_RST_CTL_RESET_EN 0x30
	170	#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
	171	#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
	172	#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
32eda7cc	173	#define QIXIS_RCW_SRC_NAND 0x119
e2b65ea9 YS	174	#define QIXIS_RST_FORCE_MEM 0x01
	175
	176	#define CONFIG_SYS_CSPR3_EXT (0x0)
	177	#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
	178	\| CSPR_PORT_SIZE_8 \
	179	\| CSPR_MSEL_GPCM \
	180	\| CSPR_V)
	181	#define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
	182	\| CSPR_PORT_SIZE_8 \
	183	\| CSPR_MSEL_GPCM \
	184	\| CSPR_V)
	185
	186	#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024)
	187	#define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12)
	188	/* QIXIS Timing parameters for IFC CS3 */
	189	#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	190	FTIM0_GPCM_TEADC(0x0e) \| \
	191	FTIM0_GPCM_TEAHC(0x0e))
	192	#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	193	FTIM1_GPCM_TRAD(0x3f))
	194	#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) \| \
	195	FTIM2_GPCM_TCH(0xf) \| \
	196	FTIM2_GPCM_TWP(0x3E))
	197	#define CONFIG_SYS_CS3_FTIM3 0x0
	198
32eda7cc SW	199	#if defined(CONFIG_SPL) && defined(CONFIG_NAND)
	200	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
	201	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY
	202	#define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR
	203	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
	204	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
	205	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
	206	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
	207	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
	208	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
	209	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
	210	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
	211	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
	212	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
	213	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
	214	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
	215	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
	216	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
	217
	218	#define CONFIG_ENV_IS_IN_NAND
	219	#define CONFIG_ENV_OFFSET (2048 * 1024)
	220	#define CONFIG_ENV_SECT_SIZE 0x20000
	221	#define CONFIG_ENV_SIZE 0x2000
	222	#define CONFIG_SPL_PAD_TO 0x80000
	223	#define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024)
	224	#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024)
	225	#else
e2b65ea9 YS	226	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
	227	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
	228	#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
	229	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
	230	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
	231	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
	232	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
	233	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
	234	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
	235	#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
	236	#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
	237	#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
	238	#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
	239	#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
	240	#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
	241	#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
	242	#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
	243
32eda7cc SW	244	#define CONFIG_ENV_IS_IN_FLASH
	245	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
	246	#define CONFIG_ENV_SECT_SIZE 0x20000
	247	#define CONFIG_ENV_SIZE 0x2000
	248	#endif
	249
e2b65ea9 YS	250	/* Debug Server firmware */
	251	#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
	252	#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
	253
e2b65ea9 YS	254	#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
	255
	256	/*
	257	* I2C
	258	*/
4012350d PK	259	#define I2C_MUX_PCA_ADDR 0x75
4012350d PK	260	#define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/
e2b65ea9 YS	261
	262	/* I2C bus multiplexer */
	263	#define I2C_MUX_CH_DEFAULT 0x8
	264
0c42a8de HW	265	/* SPI */
0c42a8de HW	266	#ifdef CONFIG_FSL_DSPI
0c42a8de	267	#define CONFIG_SPI_FLASH
0c42a8de	268	#define CONFIG_SPI_FLASH_BAR
21640db5	269	#define CONFIG_SPI_FLASH_STMICRO
0c42a8de HW	270	#endif
0c42a8de HW	271
e2b65ea9 YS	272	/*
	273	* RTC configuration
	274	*/
	275	#define RTC
	276	#define CONFIG_RTC_DS3231 1
	277	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
6581440c	278	#define CONFIG_CMD_DATE
e2b65ea9 YS	279
	280	/* EEPROM */
	281	#define CONFIG_ID_EEPROM
	282	#define CONFIG_CMD_EEPROM
	283	#define CONFIG_SYS_I2C_EEPROM_NXID
	284	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	285	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	286	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	287	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	288	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
	289
e2b65ea9	290	#define CONFIG_FSL_MEMAC
e2b65ea9 YS	291
e2b65ea9 YS	292	#ifdef CONFIG_PCI
e2b65ea9 YS	293	#define CONFIG_PCI_SCAN_SHOW
e2b65ea9 YS	294	#define CONFIG_CMD_PCI
e2b65ea9 YS	295	#endif
e2b65ea9 YS	296
8b06460e	297	/* MMC */
8b06460e	298	#ifdef CONFIG_MMC
8b06460e YL	299	#define CONFIG_FSL_ESDHC
8b06460e YL	300	#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
8b06460e	301	#endif
e2b65ea9	302
5a4d744c YL	303	#define CONFIG_MISC_INIT_R
5a4d744c YL	304
e16b604e NB	305	/*
	306	* USB
	307	*/
	308	#define CONFIG_HAS_FSL_XHCI_USB
e16b604e	309	#define CONFIG_USB_XHCI_FSL
e16b604e NB	310	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
e16b604e NB	311	#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
e16b604e	312
b99ebaf9 AG	313	#undef CONFIG_CMDLINE_EDITING
	314	#include <config_distro_defaults.h>
	315
	316	#define BOOT_TARGET_DEVICES(func) \
	317	func(USB, usb, 0) \
	318	func(MMC, mmc, 0) \
	319	func(SCSI, scsi, 0) \
	320	func(DHCP, dhcp, na)
	321	#include <config_distro_bootcmd.h>
	322
e2b65ea9 YS	323	/* Initial environment variables */
e2b65ea9 YS	324	#undef CONFIG_EXTRA_ENV_SETTINGS
9ed44787	325	#ifdef CONFIG_SECURE_BOOT
e2b65ea9 YS	326	#define CONFIG_EXTRA_ENV_SETTINGS \
e2b65ea9 YS	327	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
b99ebaf9 AG	328	"scriptaddr=0x80800000\0" \
	329	"kernel_addr_r=0x81000000\0" \
	330	"pxefile_addr_r=0x81000000\0" \
	331	"fdt_addr_r=0x88000000\0" \
	332	"ramdisk_addr_r=0x89000000\0" \
e2b65ea9 YS	333	"loadaddr=0x80100000\0" \
	334	"kernel_addr=0x100000\0" \
	335	"ramdisk_addr=0x800000\0" \
	336	"ramdisk_size=0x2000000\0" \
	337	"fdt_high=0xa0000000\0" \
	338	"initrd_high=0xffffffffffffffff\0" \
	339	"kernel_start=0x581100000\0" \
	340	"kernel_load=0xa0000000\0" \
16ed8560	341	"kernel_size=0x2800000\0" \
b99ebaf9	342	"fdtfile=fsl-ls2080a-rdb.dtb\0" \
9ed44787 UA	343	"mcinitcmd=esbc_validate 0x580c80000;" \
	344	"esbc_validate 0x580cc0000;" \
	345	"fsl_mc start mc 0x580300000" \
	346	" 0x580800000 \0" \
b99ebaf9	347	BOOTENV
9ed44787 UA	348	#else
	349	#define CONFIG_EXTRA_ENV_SETTINGS \
	350	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	351	"scriptaddr=0x80800000\0" \
	352	"kernel_addr_r=0x81000000\0" \
	353	"pxefile_addr_r=0x81000000\0" \
	354	"fdt_addr_r=0x88000000\0" \
	355	"ramdisk_addr_r=0x89000000\0" \
	356	"loadaddr=0x80100000\0" \
	357	"kernel_addr=0x100000\0" \
	358	"ramdisk_addr=0x800000\0" \
	359	"ramdisk_size=0x2000000\0" \
	360	"fdt_high=0xa0000000\0" \
	361	"initrd_high=0xffffffffffffffff\0" \
	362	"kernel_start=0x581100000\0" \
	363	"kernel_load=0xa0000000\0" \
	364	"kernel_size=0x2800000\0" \
	365	"fdtfile=fsl-ls2080a-rdb.dtb\0" \
	366	"mcinitcmd=fsl_mc start mc 0x580300000" \
	367	" 0x580800000 \0" \
	368	BOOTENV
	369	#endif
	370
e2b65ea9	371
56cd0760 PK	372	#undef CONFIG_BOOTARGS
56cd0760 PK	373	#define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \
ed77b704	374	"earlycon=uart8250,mmio,0x21c0600 " \
56cd0760	375	"ramdisk_size=0x2000000 default_hugepagesz=2m" \
9e71bb9c	376	" hugepagesz=2m hugepages=256"
56cd0760	377
b99ebaf9 AG	378	#undef CONFIG_BOOTCOMMAND
	379	/* Try to boot an on-NOR kernel first, then do normal distro boot */
	380	#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \
	381	" && cp.b $kernel_start $kernel_load $kernel_size" \
	382	" && bootm $kernel_load" \
	383	" \|\| run distro_bootcmd"
	384
3484d953 PK	385	/* MAC/PHY configuration */
	386	#ifdef CONFIG_FSL_MC_ENET
	387	#define CONFIG_PHYLIB_10G
c69384e1	388	#define CONFIG_PHY_AQUANTIA
3484d953 PK	389	#define CONFIG_PHY_CORTINA
	390	#define CONFIG_PHYLIB
	391	#define CONFIG_SYS_CORTINA_FW_IN_NOR
	392	#define CONFIG_CORTINA_FW_ADDR 0x581000000
	393	#define CONFIG_CORTINA_FW_LENGTH 0x40000
	394
	395	#define CORTINA_PHY_ADDR1 0x10
	396	#define CORTINA_PHY_ADDR2 0x11
	397	#define CORTINA_PHY_ADDR3 0x12
	398	#define CORTINA_PHY_ADDR4 0x13
	399	#define AQ_PHY_ADDR1 0x00
	400	#define AQ_PHY_ADDR2 0x01
	401	#define AQ_PHY_ADDR3 0x02
	402	#define AQ_PHY_ADDR4 0x03
abc7d0f7	403	#define AQR405_IRQ_MASK 0x36
3484d953 PK	404
3484d953 PK	405	#define CONFIG_MII
7ad9cc96	406	#define CONFIG_ETHPRIME "DPMAC1@xgmii"
3484d953	407	#define CONFIG_PHY_GIGE
95279315	408	#define CONFIG_PHY_AQUANTIA
3484d953 PK	409	#endif
3484d953 PK	410
fcfdb6d5 SJ	411	#include <asm/fsl_secure_boot.h>
fcfdb6d5 SJ	412
e2b65ea9	413	#endif /* __LS2_RDB_H */