[people/ms/u-boot.git] / include / configs / mpc8308_p1m.h

/*
 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
 * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
 *
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300		1 /* E300 family */
#define CONFIG_MPC830x		1 /* MPC830x family */
#define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
#define CONFIG_MPC8308_P1M	1 /* mpc8308_p1m board specific */

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xFC000000
#endif

/*
 * On-board devices
 *
 * TSECs
 */
#define CONFIG_TSEC1
#define CONFIG_TSEC2

/*
 * System Clock Setup
 */
#define CONFIG_83XX_CLKIN	33333333 /* in Hz */
#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN

/*
 * Hardware Reset Configuration Word
 * if CLKIN is 66.66MHz, then
 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
 * We choose the A type silicon as default, so the core is 400Mhz.
 */
#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
	HRCWL_DDR_TO_SCB_CLK_2X1 |\
	HRCWL_SVCOD_DIV_2 |\
	HRCWL_CSB_TO_CLKIN_4X1 |\
	HRCWL_CORE_TO_CSB_3X1)
/*
 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
 * in 8308's HRCWH according to the manual, but original Freescale's
 * code has them and I've expirienced some problems using the board
 * with BDI3000 attached when I've tried to set these bits to zero
 * (UART doesn't work after the 'reset run' command).
 */
#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST |\
	HRCWH_PCI1_ARBITER_ENABLE |\
	HRCWH_CORE_ENABLE |\
	HRCWH_FROM_0X00000100 |\
	HRCWH_BOOTSEQ_DISABLE |\
	HRCWH_SW_WATCHDOG_DISABLE |\
	HRCWH_ROM_LOC_LOCAL_16BIT |\
	HRCWH_RL_EXT_LEGACY |\
	HRCWH_TSEC1M_IN_MII |\
	HRCWH_TSEC2M_IN_MII |\
	HRCWH_BIG_ENDIAN)

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRH (\
	SICRH_ESDHC_A_GPIO |\
	SICRH_ESDHC_B_GPIO |\
	SICRH_ESDHC_C_GTM |\
	SICRH_GPIO_A_TSEC2 |\
	SICRH_GPIO_B_TSEC2_TX_CLK |\
	SICRH_IEEE1588_A_GPIO |\
	SICRH_USB |\
	SICRH_GTM_GPIO |\
	SICRH_IEEE1588_B_GPIO |\
	SICRH_ETSEC2_CRS |\
	SICRH_GPIOSEL_1 |\
	SICRH_TMROBI_V3P3 |\
	SICRH_TSOBI1_V3P3 |\
	SICRH_TSOBI2_V3P3)	/* 0xf577d100 */
#define CONFIG_SYS_SICRL (\
	SICRL_SPI_PF0 |\
	SICRL_UART_PF0 |\
	SICRL_IRQ_PF0 |\
	SICRL_I2C2_PF0 |\
	SICRL_ETSEC1_TX_CLK)	/* 0x00000000 */

#define CONFIG_SYS_GPIO1_PRELIM
/* GPIO Default input/output settings */
#define CONFIG_SYS_GPIO1_DIR        0x7AAF8C00
/*
 * Default GPIO values:
 * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
 */
#define CONFIG_SYS_GPIO1_DAT        0x08008C00

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR		0xE0000000

/*
 * SERDES
 */
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1	0xe3000

/*
 * Arbiter Setup
 */
#define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
#define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
#define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
				| DDRCDR_PZ_LOZ \
				| DDRCDR_NZ_LOZ \
				| DDRCDR_ODT \
				| DDRCDR_Q_DRN)
				/* 0x7b880001 */
/*
 * Manually set up DDR parameters
 * consist of two chips HY5PS12621BFP-C4 from HYNIX
 */

#define CONFIG_SYS_DDR_SIZE		128 /* MB */

#define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
					| CSCONFIG_ODT_RD_NEVER \
					| CSCONFIG_ODT_WR_ONLY_CURRENT \
					| CSCONFIG_ROW_BIT_13 \
					| CSCONFIG_COL_BIT_10)
					/* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3	0x00000000
#define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
				| (0 << TIMING_CFG0_WRT_SHIFT) \
				| (0 << TIMING_CFG0_RRT_SHIFT) \
				| (0 << TIMING_CFG0_WWT_SHIFT) \
				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
				/* 0x00220802 */
#define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
				| (6 << TIMING_CFG1_REFREC_SHIFT) \
				| (2 << TIMING_CFG1_WRREC_SHIFT) \
				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
				| (2 << TIMING_CFG1_WRTORD_SHIFT))
				/* 0x27256222 */
#define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
				| (4 << TIMING_CFG2_CPO_SHIFT) \
				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
				/* 0x121048c5 */
#define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
				/* 0x03600100 */
#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
				| SDRAM_CFG_DBW_32)
				/* 0x43080000 */

#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
				| (0x0232 << SDRAM_MODE_SD_SHIFT))
				/* ODT 150ohm CL=3, AL=1 on SDRAM */
#define CONFIG_SYS_DDR_MODE2		0x00000000

/*
 * Memory test
 */
#define CONFIG_SYS_MEMTEST_START	0x00001000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END		0x07f00000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */

#define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET	\
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR		0x00040000

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT

#define CONFIG_SYS_FLASH_BASE		0xFC000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE		64 /* FLASH size is 64M */
#define CONFIG_SYS_FLASH_PROTECTION	1 /* Use h/w Flash protection. */

/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)

#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
				| BR_PS_16	/* 16 bit port */ \
				| BR_MS_GPCM	/* MSEL = GPCM */ \
				| BR_V)		/* valid */
#define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
				| OR_UPM_XAM \
				| OR_GPCM_CSNT \
				| OR_GPCM_ACS_DIV2 \
				| OR_GPCM_XACS \
				| OR_GPCM_SCY_4 \
				| OR_GPCM_TRLX_SET \
				| OR_GPCM_EHTR_SET)

#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	512

/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_ERASE_TOUT	(1000 * 1024)
/* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	(500 * 1024)

/*
 * SJA1000 CAN controller on Local Bus
 */
#define CONFIG_SYS_SJA1000_BASE	0xFBFF0000
#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_SJA1000_BASE \
				| BR_PS_8	/* 8 bit port size */ \
				| BR_MS_GPCM	/* MSEL = GPCM */ \
				| BR_V)		/* valid */
#define CONFIG_SYS_OR1_PRELIM	(OR_AM_32KB \
				| OR_GPCM_SCY_5 \
				| OR_GPCM_EHTR_SET)
				/* 0xFFFF8052 */

#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_SJA1000_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)

/*
 * CPLD on Local Bus
 */
#define CONFIG_SYS_CPLD_BASE	0xFBFF8000
#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_CPLD_BASE \
				| BR_PS_8	/* 8 bit port */ \
				| BR_MS_GPCM	/* MSEL = GPCM */ \
				| BR_V)		/* valid */
#define CONFIG_SYS_OR2_PRELIM	(OR_AM_32KB \
				| OR_GPCM_SCY_4 \
				| OR_GPCM_EHTR_SET)
				/* 0xFFFF8042 */

#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_CPLD_BASE
#define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX	1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C2_SPEED	400000
#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCIE1_BASE		0xA0000000
#define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
#define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000

/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM	1

#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE

#define CONFIG_PCI_PNP		/* do pci plug-and-play */

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1

/*
 * TSEC
 */
#define CONFIG_TSEC_ENET	/* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET	0x24000
#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define CONFIG_SYS_TSEC2_OFFSET	0x25000
#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

/*
 * TSEC ethernet configuration
 */
#define CONFIG_MII		1 /* MII PHY management */
#define CONFIG_TSEC1_NAME	"eTSEC0"
#define CONFIG_TSEC2_NAME	"eTSEC1"
#define TSEC1_PHY_ADDR		1
#define TSEC2_PHY_ADDR		2
#define TSEC1_PHYIDX		0
#define TSEC2_PHYIDX		0
#define TSEC1_FLAGS		0
#define TSEC2_FLAGS		0

/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME		"eTSEC0"

/*
 * Environment
 */
#define CONFIG_ENV_IS_IN_FLASH	1
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
				 CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE		0x2000
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */
#define CONFIG_CMD_PCI

#define CONFIG_CMDLINE_EDITING	1	/* add command line history */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP		/* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */

#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */

/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT	0x000000000
#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
				 HID0_ENABLE_INSTRUCTION_CACHE | \
				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
#define CONFIG_SYS_HID2		HID2_HBE

/*
 * MMU Setup
 */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
					BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
					BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U

/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
					BATU_VP)
#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
					BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
					BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
					BATL_CACHEINHIBIT | \
					BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
					BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

/*
 * Environment Configuration
 */

#define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif

#define CONFIG_BAUDRATE 115200

#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */


#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"consoledev=ttyS0\0"						\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"addtty=setenv bootargs ${bootargs}"				\
		" console=${consoledev},${baudrate}\0"			\
	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
	"addmisc=setenv bootargs ${bootargs}\0"				\
	"kernel_addr=FC0A0000\0"					\
	"fdt_addr=FC2A0000\0"						\
	"ramdisk_addr=FC2C0000\0"					\
	"u-boot=mpc8308_p1m/u-boot.bin\0"				\
	"kernel_addr_r=1000000\0"					\
	"fdt_addr_r=C00000\0"						\
	"hostname=mpc8308_p1m\0"					\
	"bootfile=mpc8308_p1m/uImage\0"					\
	"fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0"				\
	"rootpath=/opt/eldk-4.2/ppc_6xx\0"				\
	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
		"tftp ${fdt_addr_r} ${fdtfile};"			\
		"run nfsargs addip addtty addmtd addmisc;"		\
		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
	"bootcmd=run flash_self\0"					\
	"load=tftp ${loadaddr} ${u-boot}\0"				\
	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)	\
		" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
		" +${filesize};cp.b ${fileaddr} "			\
		__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"	\
	"upd=run load update\0"						\

#endif	/* __CONFIG_H */
Commit	Line	Data
bc8f8c26 IY	1	/*
	2	* Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
	3	* Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
	4	*
	5	*
1a459660	6	* SPDX-License-Identifier: GPL-2.0+
bc8f8c26 IY	7	*/
	8
	9	#ifndef __CONFIG_H
	10	#define __CONFIG_H
	11
	12	/*
	13	* High Level Configuration Options
	14	*/
	15	#define CONFIG_E300 1 /* E300 family */
8afad91f	16	#define CONFIG_MPC830x 1 /* MPC830x family */
bc8f8c26 IY	17	#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
	18	#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */
	19
2ae18241 WD	20	#ifndef CONFIG_SYS_TEXT_BASE
	21	#define CONFIG_SYS_TEXT_BASE 0xFC000000
	22	#endif
	23
bc8f8c26 IY	24	/*
	25	* On-board devices
	26	*
	27	* TSECs
	28	*/
	29	#define CONFIG_TSEC1
	30	#define CONFIG_TSEC2
	31
	32	/*
	33	* System Clock Setup
	34	*/
	35	#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
	36	#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
	37
	38	/*
	39	* Hardware Reset Configuration Word
	40	* if CLKIN is 66.66MHz, then
	41	* CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
	42	* We choose the A type silicon as default, so the core is 400Mhz.
	43	*/
	44	#define CONFIG_SYS_HRCW_LOW (\
	45	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	46	HRCWL_DDR_TO_SCB_CLK_2X1 \|\
	47	HRCWL_SVCOD_DIV_2 \|\
	48	HRCWL_CSB_TO_CLKIN_4X1 \|\
	49	HRCWL_CORE_TO_CSB_3X1)
	50	/*
	51	* There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
	52	* in 8308's HRCWH according to the manual, but original Freescale's
	53	* code has them and I've expirienced some problems using the board
	54	* with BDI3000 attached when I've tried to set these bits to zero
	55	* (UART doesn't work after the 'reset run' command).
	56	*/
	57	#define CONFIG_SYS_HRCW_HIGH (\
	58	HRCWH_PCI_HOST \|\
	59	HRCWH_PCI1_ARBITER_ENABLE \|\
	60	HRCWH_CORE_ENABLE \|\
	61	HRCWH_FROM_0X00000100 \|\
	62	HRCWH_BOOTSEQ_DISABLE \|\
	63	HRCWH_SW_WATCHDOG_DISABLE \|\
	64	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	65	HRCWH_RL_EXT_LEGACY \|\
	66	HRCWH_TSEC1M_IN_MII \|\
	67	HRCWH_TSEC2M_IN_MII \|\
	68	HRCWH_BIG_ENDIAN)
	69
	70	/*
	71	* System IO Config
	72	*/
	73	#define CONFIG_SYS_SICRH (\
	74	SICRH_ESDHC_A_GPIO \|\
	75	SICRH_ESDHC_B_GPIO \|\
	76	SICRH_ESDHC_C_GTM \|\
	77	SICRH_GPIO_A_TSEC2 \|\
	78	SICRH_GPIO_B_TSEC2_TX_CLK \|\
	79	SICRH_IEEE1588_A_GPIO \|\
	80	SICRH_USB \|\
	81	SICRH_GTM_GPIO \|\
	82	SICRH_IEEE1588_B_GPIO \|\
	83	SICRH_ETSEC2_CRS \|\
	84	SICRH_GPIOSEL_1 \|\
	85	SICRH_TMROBI_V3P3 \|\
	86	SICRH_TSOBI1_V3P3 \|\
	87	SICRH_TSOBI2_V3P3) /* 0xf577d100 */
88	#define CONFIG_SYS_SICRL (\
89	SICRL_SPI_PF0 \|\
90	SICRL_UART_PF0 \|\
91	SICRL_IRQ_PF0 \|\
92	SICRL_I2C2_PF0 \|\
93	SICRL_ETSEC1_TX_CLK) /* 0x00000000 */
94
95	#define CONFIG_SYS_GPIO1_PRELIM
96	/* GPIO Default input/output settings */
97	#define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00
98	/*
99	* Default GPIO values:
100	* LED#1 enabled; WLAN enabled; Both COM LED on (orange)
101	*/
102	#define CONFIG_SYS_GPIO1_DAT 0x08008C00
103
104	/*
105	* IMMR new address
106	*/
107	#define CONFIG_SYS_IMMR 0xE0000000
108
109	/*
110	* SERDES
111	*/
112	#define CONFIG_FSL_SERDES
113	#define CONFIG_FSL_SERDES1 0xe3000
114
115	/*
116	* Arbiter Setup
117	*/
118	#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
119	#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
120	#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
121
122	/*
123	* DDR Setup
124	*/
125	#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
126	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
127	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
128	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
129	#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
130	\| DDRCDR_PZ_LOZ \
131	\| DDRCDR_NZ_LOZ \
132	\| DDRCDR_ODT \
133	\| DDRCDR_Q_DRN)
134	/* 0x7b880001 */
135	/*
136	* Manually set up DDR parameters
137	* consist of two chips HY5PS12621BFP-C4 from HYNIX
138	*/
139
140	#define CONFIG_SYS_DDR_SIZE 128 /* MB */
141
142	#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
143	#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
2fef4020 JH	144	\| CSCONFIG_ODT_RD_NEVER \
	145	\| CSCONFIG_ODT_WR_ONLY_CURRENT \
	146	\| CSCONFIG_ROW_BIT_13 \
	147	\| CSCONFIG_COL_BIT_10)
	148	/* 0x80010102 */
bc8f8c26 IY	149	#define CONFIG_SYS_DDR_TIMING_3 0x00000000
	150	#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
	151	\| (0 << TIMING_CFG0_WRT_SHIFT) \
	152	\| (0 << TIMING_CFG0_RRT_SHIFT) \
	153	\| (0 << TIMING_CFG0_WWT_SHIFT) \
	154	\| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
	155	\| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
	156	\| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
	157	\| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
	158	/* 0x00220802 */
	159	#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
	160	\| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
	161	\| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
	162	\| (5 << TIMING_CFG1_CASLAT_SHIFT) \
	163	\| (6 << TIMING_CFG1_REFREC_SHIFT) \
	164	\| (2 << TIMING_CFG1_WRREC_SHIFT) \
	165	\| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
	166	\| (2 << TIMING_CFG1_WRTORD_SHIFT))
	167	/* 0x27256222 */
	168	#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
	169	\| (4 << TIMING_CFG2_CPO_SHIFT) \
	170	\| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
	171	\| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
	172	\| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
	173	\| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
	174	\| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
	175	/* 0x121048c5 */
	176	#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
	177	\| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
	178	/* 0x03600100 */
	179	#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
	180	\| SDRAM_CFG_SDRAM_TYPE_DDR2 \
2fef4020	181	\| SDRAM_CFG_DBW_32)
bc8f8c26 IY	182	/* 0x43080000 */
	183
	184	#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
	185	#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
	186	\| (0x0232 << SDRAM_MODE_SD_SHIFT))
	187	/* ODT 150ohm CL=3, AL=1 on SDRAM */
	188	#define CONFIG_SYS_DDR_MODE2 0x00000000
	189
	190	/*
	191	* Memory test
	192	*/
	193	#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
	194	#define CONFIG_SYS_MEMTEST_END 0x07f00000
	195
	196	/*
	197	* The reserved memory
	198	*/
14d0a02a	199	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
bc8f8c26 IY	200
	201	#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
	202	#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
	203
	204	/*
	205	* Initial RAM Base Address Setup
	206	*/
	207	#define CONFIG_SYS_INIT_RAM_LOCK 1
	208	#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
80ae4df9	209	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
bc8f8c26	210	#define CONFIG_SYS_GBL_DATA_OFFSET \
25ddd1fb	211	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
bc8f8c26 IY	212
	213	/*
	214	* Local Bus Configuration & Clock Setup
	215	*/
	216	#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
	217	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
	218	#define CONFIG_SYS_LBC_LBCR 0x00040000
	219
	220	/*
	221	* FLASH on the Local Bus
	222	*/
	223	#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
	224	#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
	225	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	226
	227	#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
	228	#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
	229	#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
	230
	231	/* Window base at flash base */
	232	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
	233	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_64MB)
	234
7d6a0982 JH	235	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
	236	\| BR_PS_16 /* 16 bit port */ \
	237	\| BR_MS_GPCM /* MSEL = GPCM */ \
	238	\| BR_V) /* valid */
	239	#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
bc8f8c26 IY	240	\| OR_UPM_XAM \
	241	\| OR_GPCM_CSNT \
	242	\| OR_GPCM_ACS_DIV2 \
	243	\| OR_GPCM_XACS \
	244	\| OR_GPCM_SCY_4 \
7d6a0982 JH	245	\| OR_GPCM_TRLX_SET \
7d6a0982 JH	246	\| OR_GPCM_EHTR_SET)
bc8f8c26 IY	247
	248	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	249	#define CONFIG_SYS_MAX_FLASH_SECT 512
	250
	251	/* Flash Erase Timeout (ms) */
	252	#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024)
	253	/* Flash Write Timeout (ms) */
	254	#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024)
	255
	256	/*
	257	* SJA1000 CAN controller on Local Bus
	258	*/
80ae4df9 JH	259	#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
80ae4df9 JH	260	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SJA1000_BASE \
7d6a0982 JH	261	\| BR_PS_8 /* 8 bit port size */ \
	262	\| BR_MS_GPCM /* MSEL = GPCM */ \
	263	\| BR_V) /* valid */
	264	#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \
bc8f8c26	265	\| OR_GPCM_SCY_5 \
7d6a0982	266	\| OR_GPCM_EHTR_SET)
bc8f8c26 IY	267	/* 0xFFFF8052 */
	268
	269	#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE
	270	#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN \| LBLAWAR_32KB)
	271
	272	/*
	273	* CPLD on Local Bus
	274	*/
80ae4df9 JH	275	#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
80ae4df9 JH	276	#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_CPLD_BASE \
7d6a0982 JH	277	\| BR_PS_8 /* 8 bit port */ \
	278	\| BR_MS_GPCM /* MSEL = GPCM */ \
	279	\| BR_V) /* valid */
	280	#define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB \
bc8f8c26	281	\| OR_GPCM_SCY_4 \
7d6a0982	282	\| OR_GPCM_EHTR_SET)
bc8f8c26 IY	283	/* 0xFFFF8042 */
	284
	285	#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE
	286	#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN \| LBLAWAR_32KB)
	287
	288	/*
	289	* Serial Port
	290	*/
	291	#define CONFIG_CONS_INDEX 1
	292	#undef CONFIG_SERIAL_SOFTWARE_FIFO
bc8f8c26 IY	293	#define CONFIG_SYS_NS16550_SERIAL
	294	#define CONFIG_SYS_NS16550_REG_SIZE 1
	295	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	296
	297	#define CONFIG_SYS_BAUDRATE_TABLE \
	298	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
	299
	300	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
	301	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
	302
bc8f8c26	303	/* I2C */
00f792e0 HS	304	#define CONFIG_SYS_I2C
	305	#define CONFIG_SYS_I2C_FSL
	306	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	307	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	308	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	309	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	310	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	311	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
bc8f8c26 IY	312
	313	/*
	314	* General PCI
	315	* Addresses are mapped 1-1.
	316	*/
	317	#define CONFIG_SYS_PCIE1_BASE 0xA0000000
	318	#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
	319	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
	320	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
	321	#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
	322	#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
	323	#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
	324	#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
	325	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
	326
	327	/* enable PCIE clock */
	328	#define CONFIG_SYS_SCCR_PCIEXP1CM 1
	329
842033e6	330	#define CONFIG_PCI_INDIRECT_BRIDGE
bc8f8c26 IY	331	#define CONFIG_PCIE
	332
	333	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	334
	335	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
	336	#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
	337
	338	/*
	339	* TSEC
	340	*/
bc8f8c26 IY	341	#define CONFIG_TSEC_ENET /* TSEC ethernet support */
	342	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	343	#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
	344	#define CONFIG_SYS_TSEC2_OFFSET 0x25000
	345	#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
	346
	347	/*
	348	* TSEC ethernet configuration
	349	*/
	350	#define CONFIG_MII 1 /* MII PHY management */
	351	#define CONFIG_TSEC1_NAME "eTSEC0"
	352	#define CONFIG_TSEC2_NAME "eTSEC1"
	353	#define TSEC1_PHY_ADDR 1
	354	#define TSEC2_PHY_ADDR 2
	355	#define TSEC1_PHYIDX 0
	356	#define TSEC2_PHYIDX 0
	357	#define TSEC1_FLAGS 0
	358	#define TSEC2_FLAGS 0
	359
	360	/* Options are: eTSEC[0-1] */
	361	#define CONFIG_ETHPRIME "eTSEC0"
	362
	363	/*
	364	* Environment
	365	*/
	366	#define CONFIG_ENV_IS_IN_FLASH 1
	367	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
	368	CONFIG_SYS_MONITOR_LEN)
	369	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	370	#define CONFIG_ENV_SIZE 0x2000
	371	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
	372	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	373
	374	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	375	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
	376
	377	/*
	378	* BOOTP options
	379	*/
	380	#define CONFIG_BOOTP_BOOTFILESIZE
	381	#define CONFIG_BOOTP_BOOTPATH
	382	#define CONFIG_BOOTP_GATEWAY
	383	#define CONFIG_BOOTP_HOSTNAME
	384
	385	/*
	386	* Command line configuration.
	387	*/
bc8f8c26	388	#define CONFIG_CMD_PCI
bc8f8c26 IY	389
	390	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	391
	392	/*
	393	* Miscellaneous configurable options
	394	*/
	395	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	396	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
bc8f8c26 IY	397
	398	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	399
	400	/* Print Buffer Size */
	401	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	402	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	403	/* Boot Argument Buffer Size */
	404	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
bc8f8c26 IY	405
	406	/*
	407	* For booting Linux, the board info and command line data
	408	* have to be in the first 8 MB of memory, since this is
	409	* the maximum mapped by the Linux kernel during initialization.
	410	*/
9eda770b	411	#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
bc8f8c26 IY	412
	413	/*
	414	* Core HID Setup
	415	*/
	416	#define CONFIG_SYS_HID0_INIT 0x000000000
	417	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \| \
	418	HID0_ENABLE_INSTRUCTION_CACHE \| \
	419	HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
	420	#define CONFIG_SYS_HID2 HID2_HBE
	421
	422	/*
	423	* MMU Setup
	424	*/
	425
	426	/* DDR: cache cacheable */
72cd4087	427	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \| BATL_PP_RW \| \
bc8f8c26 IY	428	BATL_MEMCOHERENCE)
	429	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \| BATU_BL_128M \| \
	430	BATU_VS \| BATU_VP)
	431	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	432	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
	433
	434	/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
72cd4087	435	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \| BATL_PP_RW \| \
bc8f8c26 IY	436	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	437	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \| BATU_BL_8M \| BATU_VS \| \
	438	BATU_VP)
	439	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	440	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
	441
	442	/* FLASH: icache cacheable, but dcache-inhibit and guarded */
72cd4087	443	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \| BATL_PP_RW \| \
bc8f8c26 IY	444	BATL_MEMCOHERENCE)
	445	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \| BATU_BL_8M \| \
	446	BATU_VS \| BATU_VP)
72cd4087	447	#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \| BATL_PP_RW \| \
bc8f8c26 IY	448	BATL_CACHEINHIBIT \| \
	449	BATL_GUARDEDSTORAGE)
	450	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
	451
	452	/* Stack in dcache: cacheable, no memory coherence */
72cd4087	453	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_RW)
bc8f8c26 IY	454	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR \| BATU_BL_128K \| \
	455	BATU_VS \| BATU_VP)
	456	#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
	457	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
	458
bc8f8c26 IY	459	/*
	460	* Environment Configuration
	461	*/
	462
	463	#define CONFIG_ENV_OVERWRITE
	464
	465	#if defined(CONFIG_TSEC_ENET)
	466	#define CONFIG_HAS_ETH0
	467	#define CONFIG_HAS_ETH1
	468	#endif
	469
	470	#define CONFIG_BAUDRATE 115200
	471
	472	#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
	473
bc8f8c26	474
bc8f8c26 IY	475	#define CONFIG_EXTRA_ENV_SETTINGS \
	476	"netdev=eth0\0" \
	477	"consoledev=ttyS0\0" \
	478	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	479	"nfsroot=${serverip}:${rootpath}\0" \
	480	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	481	"addip=setenv bootargs ${bootargs} " \
	482	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	483	":${hostname}:${netdev}:off panic=1\0" \
	484	"addtty=setenv bootargs ${bootargs}" \
	485	" console=${consoledev},${baudrate}\0" \
	486	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
	487	"addmisc=setenv bootargs ${bootargs}\0" \
	488	"kernel_addr=FC0A0000\0" \
	489	"fdt_addr=FC2A0000\0" \
	490	"ramdisk_addr=FC2C0000\0" \
	491	"u-boot=mpc8308_p1m/u-boot.bin\0" \
	492	"kernel_addr_r=1000000\0" \
	493	"fdt_addr_r=C00000\0" \
	494	"hostname=mpc8308_p1m\0" \
	495	"bootfile=mpc8308_p1m/uImage\0" \
	496	"fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \
	497	"rootpath=/opt/eldk-4.2/ppc_6xx\0" \
	498	"flash_self=run ramargs addip addtty addmtd addmisc;" \
	499	"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
	500	"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
	501	"bootm ${kernel_addr} - ${fdt_addr}\0" \
	502	"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
	503	"tftp ${fdt_addr_r} ${fdtfile};" \
	504	"run nfsargs addip addtty addmtd addmisc;" \
	505	"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
	506	"bootcmd=run flash_self\0" \
	507	"load=tftp ${loadaddr} ${u-boot}\0" \
93ea89f0 MV	508	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
93ea89f0 MV	509	" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
bc8f8c26	510	" +${filesize};cp.b ${fileaddr} " \
93ea89f0	511	__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
bc8f8c26 IY	512	"upd=run load update\0" \
	513
	514	#endif /* __CONFIG_H */