configs: Migrate CONFIG_SYS_TEXT_BASE

[people/ms/u-boot.git] / include / configs / mx31ads.h

/*
 * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
 *
 * Configuration settings for the MX31ADS Freescale board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <asm/arch/imx-regs.h>

 /* High Level Configuration Options */
#define CONFIG_MX31		1		/* This is a mx31 */

#define CONFIG_MACH_TYPE	MACH_TYPE_MX31ADS

#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS	1
#define CONFIG_INITRD_TAG		1

/*
 * Size of malloc() pool
 */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128 * 1024)

/*
 * Hardware drivers
 */

#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE	UART1_BASE

#define CONFIG_HARD_SPI		1
#define CONFIG_MXC_SPI		1
#define CONFIG_DEFAULT_SPI_BUS	1
#define CONFIG_DEFAULT_SPI_MODE	(SPI_MODE_0 | SPI_CS_HIGH)

/* PMIC Controller */
#define CONFIG_POWER
#define CONFIG_POWER_SPI
#define CONFIG_POWER_FSL
#define CONFIG_FSL_PMIC_BUS	1
#define CONFIG_FSL_PMIC_CS	0
#define CONFIG_FSL_PMIC_CLK	1000000
#define CONFIG_FSL_PMIC_MODE	(SPI_MODE_0 | SPI_CS_HIGH)
#define CONFIG_FSL_PMIC_BITLEN	32
#define CONFIG_RTC_MC13XXX

/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX	1

#define CONFIG_LOADADDR		0x80800000	/* loadaddr env var */

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"uboot_addr=0xa0000000\0"					\
	"uboot=mx31ads/u-boot.bin\0"					\
	"kernel=mx31ads/uImage\0"					\
	"nfsroot=/opt/eldk/arm\0"					\
	"bootargs_base=setenv bootargs console=ttymxc0,115200\0"	\
	"bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs "	\
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0"	\
	"bootcmd=run bootcmd_net\0"					\
	"bootcmd_net=run bootargs_base bootargs_nfs; "			\
		"tftpboot ${loadaddr} ${kernel}; bootm\0"		\
	"prg_uboot=tftpboot ${loadaddr} ${uboot}; "			\
		"protect off ${uboot_addr} 0xa003ffff; "		\
		"erase ${uboot_addr} 0xa003ffff; "			\
		"cp.b ${loadaddr} ${uboot_addr} ${filesize}; "		\
		"setenv filesize; saveenv\0"

#define CONFIG_CS8900
#define CONFIG_CS8900_BASE	0xb4020300
#define CONFIG_CS8900_BUS16		1	/* follow the Linux driver */

/*
 * The MX31ADS board seems to have a hardware "peculiarity" confirmed under
 * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A
 * controller inverted. The controller is capable of detecting and correcting
 * this, but it needs 4 network packets for that. Which means, at startup, you
 * will not receive answers to the first 4 packest, unless there have been some
 * broadcasts on the network, or your board is on a hub. Reducing the ARP
 * timeout from default 5 seconds to 200ms we speed up the initial TFTP
 * transfer, should the user wish one, significantly.
 */
#define CONFIG_ARP_TIMEOUT	200UL

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP		/* undef to save memory */

#define CONFIG_SYS_MEMTEST_START	0		/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x10000

#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

#define CONFIG_CMDLINE_EDITING	1

/*-----------------------------------------------------------------------
 * Physical Memory Map
 */
#define CONFIG_NR_DRAM_BANKS	1
#define PHYS_SDRAM_1		CSD0_BASE
#define PHYS_SDRAM_1_SIZE	(128 * 1024 * 1024)

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
						GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_INIT_RAM_ADDR + \
						CONFIG_SYS_GBL_DATA_OFFSET)

/*-----------------------------------------------------------------------
 * FLASH and environment organization
 */
#define CONFIG_SYS_FLASH_BASE		CS0_BASE
#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT	262		/* max number of sectors on one chip */
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE	/* Monitor at beginning of flash */
#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256KiB */

#define CONFIG_ENV_SECT_SIZE	(128 * 1024)
#define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

/*-----------------------------------------------------------------------
 * CFI FLASH driver setup
 */
#define CONFIG_SYS_FLASH_CFI			1 /* Flash memory is CFI compliant */
#define CONFIG_FLASH_CFI_DRIVER		1 /* Use drivers/cfi_flash.c */
#define CONFIG_FLASH_SPANSION_S29WS_N	1 /* A non-standard buffered write algorithm */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1 /* Use buffered writes (~10x faster) */
#define CONFIG_SYS_FLASH_PROTECTION		1 /* Use hardware sector protection */

/*
 * JFFS2 partitions
 */
#define CONFIG_JFFS2_DEV	"nor0"

#endif /* __CONFIG_H */