[people/ms/u-boot.git] / include / configs / pcm058.h

/*
 * Copyright (C) Stefano Babic <sbabic@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */


#ifndef __PCM058_CONFIG_H
#define __PCM058_CONFIG_H

#include <config_distro_defaults.h>

#ifdef CONFIG_SPL
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS	(64 * 1024)
#include "imx6_spl.h"
#endif

#include "mx6_common.h"

/* Thermal */
#define CONFIG_IMX_THERMAL

/* Serial */
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE	       UART2_BASE
#define CONFIG_CONSOLE_DEV		"ttymxc1"

#define PHYS_SDRAM_SIZE		(1u * 1024 * 1024 * 1024)

/* Early setup */
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_DISPLAY_BOARDINFO_LATE


/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(8 * SZ_1M)

/* Ethernet */
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE			ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_ETHPRIME			"FEC"
#define CONFIG_FEC_MXC_PHYADDR		3

#define CONFIG_PHYLIB
#define CONFIG_PHY_MICREL
#define CONFIG_PHY_KSZ9031

/* SPI Flash */
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS		0
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED		20000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0

/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_SPEED		  100000

#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_NAND
/* Enable NAND support */
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
#endif

/* DMA stuff, needed for GPMI/MXS NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8

/* Filesystem support */
#define CONFIG_LZO
#define CONFIG_CMD_UBIFS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE
#define MTDIDS_DEFAULT    "nand0=nand"
#define MTDPARTS_DEFAULT  "mtdparts=nand:16m(uboot),1m(env),-(rootfs)"

/* Various command support */
#define CONFIG_CMD_BMODE         /* set eFUSE shadow for a boot dev and reset */
#define CONFIG_CMD_HDMIDETECT    /* detect HDMI output device */
#define CONFIG_CMD_GSC
#define CONFIG_CMD_EECONFIG      /* Gateworks EEPROM config cmd */
#define CONFIG_RBTREE

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS           1
#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR	0
#define CONFIG_SYS_FSL_USDHC_NUM	1

/* Environment organization */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE                (16 * 1024)
#define CONFIG_ENV_OFFSET		(1024 * SZ_1K)
#define CONFIG_ENV_SECT_SIZE		(64 * SZ_1K)
#define CONFIG_ENV_SPI_BUS             CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS              CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE            CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ          CONFIG_SF_DEFAULT_SPEED
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_OFFSET_REDUND       (CONFIG_ENV_OFFSET + \
						CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND         CONFIG_ENV_SIZE

#ifdef CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET              (0x1E0000)
#define CONFIG_ENV_SECT_SIZE           (128 * SZ_1K)
#endif

#endif
Commit	Line	Data
876a25d2 SB	1	/*
	2	* Copyright (C) Stefano Babic <sbabic@denx.de>
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7
	8	#ifndef __PCM058_CONFIG_H
	9	#define __PCM058_CONFIG_H
	10
	11	#include <config_distro_defaults.h>
	12
	13	#ifdef CONFIG_SPL
876a25d2 SB	14	#define CONFIG_SPL_SPI_LOAD
	15	#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
	16	#include "imx6_spl.h"
	17	#endif
	18
	19	#include "mx6_common.h"
	20
	21	/* Thermal */
	22	#define CONFIG_IMX_THERMAL
	23
	24	/* Serial */
	25	#define CONFIG_MXC_UART
	26	#define CONFIG_MXC_UART_BASE UART2_BASE
	27	#define CONFIG_CONSOLE_DEV "ttymxc1"
	28
	29	#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
	30
	31	/* Early setup */
	32	#define CONFIG_BOARD_EARLY_INIT_F
	33	#define CONFIG_BOARD_LATE_INIT
	34	#define CONFIG_DISPLAY_BOARDINFO_LATE
	35
	36
	37	/* Size of malloc() pool */
	38	#define CONFIG_SYS_MALLOC_LEN (8 * SZ_1M)
	39
	40	/* Ethernet */
	41	#define CONFIG_FEC_MXC
	42	#define CONFIG_MII
	43	#define IMX_FEC_BASE ENET_BASE_ADDR
	44	#define CONFIG_FEC_XCV_TYPE RGMII
	45	#define CONFIG_ETHPRIME "FEC"
	46	#define CONFIG_FEC_MXC_PHYADDR 3
	47
	48	#define CONFIG_PHYLIB
	49	#define CONFIG_PHY_MICREL
	50	#define CONFIG_PHY_KSZ9031
	51
	52	/* SPI Flash */
	53	#define CONFIG_MXC_SPI
	54	#define CONFIG_SF_DEFAULT_BUS 0
	55	#define CONFIG_SF_DEFAULT_CS 0
	56	#define CONFIG_SF_DEFAULT_SPEED 20000000
	57	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
	58
	59	/* I2C Configs */
	60	#define CONFIG_SYS_I2C
	61	#define CONFIG_SYS_I2C_MXC
	62	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 2 */
	63	#define CONFIG_SYS_I2C_SPEED 100000
	64
	65	#ifndef CONFIG_SPL_BUILD
	66	#define CONFIG_CMD_NAND
	67	/* Enable NAND support */
	68	#define CONFIG_CMD_NAND_TRIMFFS
	69	#define CONFIG_NAND_MXS
	70	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	71	#define CONFIG_SYS_NAND_BASE 0x40000000
	72	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	73	#define CONFIG_SYS_NAND_ONFI_DETECTION
	74	#endif
	75
	76	/* DMA stuff, needed for GPMI/MXS NAND support */
	77	#define CONFIG_APBH_DMA
78	#define CONFIG_APBH_DMA_BURST
79	#define CONFIG_APBH_DMA_BURST8
80
81	/* Filesystem support */
82	#define CONFIG_LZO
83	#define CONFIG_CMD_UBIFS
84	#define CONFIG_CMD_MTDPARTS
85	#define CONFIG_MTD_PARTITIONS
86	#define CONFIG_MTD_DEVICE
87	#define MTDIDS_DEFAULT "nand0=nand"
88	#define MTDPARTS_DEFAULT "mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
89
90	/* Various command support */
91	#define CONFIG_CMD_BMODE /* set eFUSE shadow for a boot dev and reset */
92	#define CONFIG_CMD_HDMIDETECT /* detect HDMI output device */
93	#define CONFIG_CMD_GSC
94	#define CONFIG_CMD_EECONFIG /* Gateworks EEPROM config cmd */
876a25d2 SB	95	#define CONFIG_RBTREE
	96
	97	/* Physical Memory Map */
	98	#define CONFIG_NR_DRAM_BANKS 1
	99	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
	100
	101	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	102	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	103	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
	104
	105	#define CONFIG_SYS_INIT_SP_OFFSET \
	106	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	107	#define CONFIG_SYS_INIT_SP_ADDR \
	108	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
	109
	110	/* MMC Configs */
	111	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	112	#define CONFIG_SYS_FSL_USDHC_NUM 1
	113
	114	/* Environment organization */
	115	#define CONFIG_ENV_IS_IN_SPI_FLASH
	116	#define CONFIG_ENV_SIZE (16 * 1024)
	117	#define CONFIG_ENV_OFFSET (1024 * SZ_1K)
	118	#define CONFIG_ENV_SECT_SIZE (64 * SZ_1K)
	119	#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
	120	#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
	121	#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
	122	#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
	123	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	124	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
	125	CONFIG_ENV_SECT_SIZE)
	126	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	127
	128	#ifdef CONFIG_ENV_IS_IN_NAND
	129	#define CONFIG_ENV_OFFSET (0x1E0000)
	130	#define CONFIG_ENV_SECT_SIZE (128 * SZ_1K)
	131	#endif
	132
	133	#endif