[people/ms/u-boot.git] / include / configs / tqma6.h

/*
 * Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
 *
 * Configuration settings for the TQ Systems TQMa6<Q,S> module.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <linux/kconfig.h>
/* SPL */
/* #if defined(CONFIG_SPL_BUILD) */

#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_EXT_SUPPORT

/* common IMX6 SPL configuration */
#include "imx6_spl.h"

/* #endif */

/* place code in last 4 MiB of RAM */
#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
#define CONFIG_SYS_TEXT_BASE		0x2fc00000
#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
#define CONFIG_SYS_TEXT_BASE		0x4fc00000
#endif

#include "mx6_common.h"

#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
#define PHYS_SDRAM_SIZE			(512u * SZ_1M)
#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
#define PHYS_SDRAM_SIZE			(1024u * SZ_1M)
#endif

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT

#define CONFIG_MXC_UART

/* SPI */
#define CONFIG_CMD_SPI
#define CONFIG_MXC_SPI

/* SPI Flash */

#define TQMA6_SPI_FLASH_SECTOR_SIZE	SZ_64K

#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_BUS	0
#define CONFIG_SF_DEFAULT_CS	0
#define CONFIG_SF_DEFAULT_SPEED	50000000
#define CONFIG_SF_DEFAULT_MODE	(SPI_MODE_0)

/* I2C Configs */
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED		100000

/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM75
#define CONFIG_DTT_MAX_TEMP		70
#define CONFIG_DTT_MIN_TEMP		-30
#define CONFIG_DTT_HYSTERESIS	3
#define CONFIG_CMD_DTT

/* I2C EEPROM (M24C64) */
#define CONFIG_SYS_I2C_EEPROM_ADDR			0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN			2
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS		5 /* 32 Bytes */
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS	20
#define CONFIG_CMD_EEPROM

#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
#define TQMA6_PFUZE100_I2C_BUS		2

/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR	0

/* USB Configs */
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */

#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII

#define CONFIG_FEC_MXC
#define IMX_FEC_BASE			ENET_BASE_ADDR
#define CONFIG_PHYLIB
#define CONFIG_MII

#define CONFIG_ARP_TIMEOUT		200UL
/* Network config - Allow larger/faster download for TFTP/NFS */
#define CONFIG_IP_DEFRAG
#define CONFIG_TFTP_BLOCKSIZE	4096
#define CONFIG_NFS_READ_SIZE	4096

/* Command definition */
#define CONFIG_CMD_BMODE

#define CONFIG_ENV_SIZE			(SZ_8K)
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * SZ_1M)

#if defined(CONFIG_TQMA6X_MMC_BOOT)

#define CONFIG_ENV_IS_IN_MMC
#define TQMA6_UBOOT_OFFSET		SZ_1K
#define TQMA6_UBOOT_SECTOR_START	0x2
#define TQMA6_UBOOT_SECTOR_COUNT	0x7fe

#define CONFIG_ENV_OFFSET		SZ_1M
#define CONFIG_SYS_MMC_ENV_DEV		0

#define TQMA6_FDT_OFFSET		(2 * SZ_1M)
#define TQMA6_FDT_SECTOR_START		0x1000
#define TQMA6_FDT_SECTOR_COUNT		0x800

#define TQMA6_KERNEL_SECTOR_START	0x2000
#define TQMA6_KERNEL_SECTOR_COUNT	0x2000

#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
	"uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
	"uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
	"fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
	"kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
	"loadimage=mmc dev ${mmcdev}; "                                        \
		"mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
	"loadfdt=mmc dev ${mmcdev}; "                                          \
		"mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
	"update_uboot=if tftp ${uboot}; then "                                 \
		"if itest ${filesize} > 0; then "                              \
			"mmc dev ${mmcdev}; mmc rescan; "                      \
			"setexpr blkc ${filesize} / 0x200; "                   \
			"setexpr blkc ${blkc} + 1; "                           \
			"if itest ${blkc} <= ${uboot_size}; then "             \
				"mmc write ${loadaddr} ${uboot_start} "        \
					"${blkc}; "                            \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize; setenv blkc \0"                              \
	"update_kernel=run kernel_name; "                                      \
		"if tftp ${kernel}; then "                                     \
			"if itest ${filesize} > 0; then "                      \
				"mmc dev ${mmcdev}; mmc rescan; "              \
				"setexpr blkc ${filesize} / 0x200; "           \
				"setexpr blkc ${blkc} + 1; "                   \
				"if itest ${blkc} <= ${kernel_size}; then "    \
					"mmc write ${loadaddr} "               \
						"${kernel_start} ${blkc}; "    \
				"fi; "                                         \
			"fi; "                                                 \
		"fi; "                                                         \
		"setenv filesize; setenv blkc \0"                              \
	"update_fdt=if tftp ${fdt_file}; then "                                \
		"if itest ${filesize} > 0; then "                              \
			"mmc dev ${mmcdev}; mmc rescan; "                      \
			"setexpr blkc ${filesize} / 0x200; "                   \
			"setexpr blkc ${blkc} + 1; "                           \
			"if itest ${blkc} <= ${fdt_size}; then "               \
				"mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize; setenv blkc \0"                              \

#define CONFIG_BOOTCOMMAND \
	"run mmcboot; run netboot; run panicboot"

#elif defined(CONFIG_TQMA6X_SPI_BOOT)

#define TQMA6_UBOOT_OFFSET		0x400
#define TQMA6_UBOOT_SECTOR_START	0x0
/* max u-boot size: 512k */
#define TQMA6_UBOOT_SECTOR_SIZE		TQMA6_SPI_FLASH_SECTOR_SIZE
#define TQMA6_UBOOT_SECTOR_COUNT	0x8
#define TQMA6_UBOOT_SIZE		(TQMA6_UBOOT_SECTOR_SIZE * \
					 TQMA6_UBOOT_SECTOR_COUNT)

#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_OFFSET		(TQMA6_UBOOT_SIZE)
#define CONFIG_ENV_SECT_SIZE		TQMA6_SPI_FLASH_SECTOR_SIZE
#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
					 CONFIG_ENV_SECT_SIZE)

#define CONFIG_ENV_SPI_BUS		(CONFIG_SF_DEFAULT_BUS)
#define CONFIG_ENV_SPI_CS		(CONFIG_SF_DEFAULT_CS)
#define CONFIG_ENV_SPI_MAX_HZ		(CONFIG_SF_DEFAULT_SPEED)
#define CONFIG_ENV_SPI_MODE		(CONFIG_SF_DEFAULT_MODE)

#define TQMA6_FDT_OFFSET		(CONFIG_ENV_OFFSET_REDUND + \
					 CONFIG_ENV_SECT_SIZE)
#define TQMA6_FDT_SECT_SIZE		(TQMA6_SPI_FLASH_SECTOR_SIZE)

#define TQMA6_FDT_SECTOR_START		0x0a /* 8 Sector u-boot, 2 Sector env */
#define TQMA6_FDT_SECTOR_COUNT		0x01

#define TQMA6_KERNEL_SECTOR_START	0x10
#define TQMA6_KERNEL_SECTOR_COUNT	0x60

#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
	"mmcblkdev=0\0"                                                        \
	"uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
	"uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
	"fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
	"kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
	"update_uboot=if tftp ${uboot}; then "                                 \
		"if itest ${filesize} > 0; then "                              \
			"setexpr blkc ${filesize} + "                          \
				__stringify(TQMA6_UBOOT_OFFSET) "; "           \
			"setexpr size ${uboot_sectors} * "                     \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"if itest ${blkc} <= ${size}; then "                   \
				"sf probe; "                                   \
				"sf erase 0 ${size}; "                         \
				"sf write ${loadaddr} ${uboot_offset} "        \
					"${filesize}; "                        \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize 0; setenv blkc; setenv size \0"               \
	"update_kernel=run kernel_name; if tftp ${kernel}; then "              \
		"if itest ${filesize} > 0; then "                              \
			"setexpr size ${kernel_sectors} * "                    \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"setexpr offset ${kernel_start} * "                    \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"if itest ${filesize} <= ${size}; then "               \
				"sf probe; "                                   \
				"sf erase ${offset} ${size}; "                 \
				"sf write ${loadaddr} ${offset} "              \
					"${filesize}; "                        \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize 0; setenv size ; setenv offset\0"             \
	"update_fdt=if tftp ${fdt_file}; then "                                \
		"if itest ${filesize} > 0; then "                              \
			"setexpr size ${fdt_sectors} * "                       \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"setexpr offset ${fdt_start} * "                       \
				__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
			"if itest ${filesize} <= ${size}; then "               \
				"sf probe; "                                   \
				"sf erase ${offset} ${size}; "                 \
				"sf write ${loadaddr} ${offset} "              \
					"${filesize}; "                        \
			"fi; "                                                 \
		"fi; fi; "                                                     \
		"setenv filesize 0; setenv size ; setenv offset\0"             \
	"loadimage=sf probe; "                                                 \
		"setexpr size ${kernel_sectors} * "                            \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"setexpr offset ${kernel_start} * "                            \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"sf read ${loadaddr} ${offset} ${size}; "                      \
		"setenv size ; setenv offset\0"                                \
	"loadfdt=sf probe; "                                                   \
		"setexpr size ${fdt_sectors} * "                               \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"setexpr offset ${fdt_start} * "                               \
			__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
		"sf read ${${fdt_addr}} ${offset} ${size}; "                   \
		"setenv size ; setenv offset\0"                                \


#define CONFIG_BOOTCOMMAND                                                     \
	"sf probe; run mmcboot; run netboot; run panicboot"                    \

#else

#error "need to define boot source"

#endif

/* 128 MiB offset as in ARM related docu for linux suggested */
#define TQMA6_FDT_ADDRESS		0x18000000

#define CONFIG_EXTRA_ENV_SETTINGS                                              \
	"board=tqma6\0"                                                        \
	"uimage=uImage\0"                                                      \
	"zimage=zImage\0"                                                      \
	"boot_type=bootz\0"                                                    \
	"kernel_name=if test \"${boot_type}\" != bootz; then "                 \
		"setenv kernel ${uimage}; "                                    \
		"else setenv kernel ${zimage}; fi\0"                           \
	"uboot=u-boot.imx\0"                                                   \
	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
	"fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
	"console=" CONFIG_CONSOLE_DEV "\0"                                     \
	"fdt_high=0xffffffff\0"                                                \
	"initrd_high=0xffffffff\0"                                             \
	"addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
	"addfb=setenv bootargs ${bootargs} "                                   \
		"imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
	"mmcpart=2\0"                                                          \
	"mmcblkdev=0\0"                                                        \
	"mmcargs=run addmmc addtty addfb\0"                                    \
	"addmmc=setenv bootargs ${bootargs} "                                  \
		"root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0"        \
	"mmcboot=echo Booting from mmc ...; "                                  \
		"setenv bootargs; "                                            \
		"run mmcargs; "                                                \
		"run loadimage; "                                              \
		"if run loadfdt; then "                                        \
			"echo boot device tree kernel ...; "                   \
			"${boot_type} ${loadaddr} - ${fdt_addr}; "             \
		"else "                                                        \
			"${boot_type}; "                                       \
		"fi;\0"                                                        \
		"setenv bootargs \0"                                           \
	"netdev=eth0\0"                                                        \
	"rootpath=/srv/nfs/tqma6\0"                                            \
	"ipmode=static\0"                                                      \
	"netargs=run addnfs addip addtty addfb\0"                              \
	"addnfs=setenv bootargs ${bootargs} "                                  \
		"root=/dev/nfs rw "                                            \
		"nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
	"addip_static=setenv bootargs ${bootargs} "                            \
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
		"${hostname}:${netdev}:off\0"                                  \
	"addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
	"addip=if test \"${ipmode}\" != static; then "                         \
		"run addip_dynamic; else run addip_static; fi\0"               \
	"set_getcmd=if test \"${ipmode}\" != static; then "                    \
		"setenv getcmd dhcp; setenv autoload yes; "                    \
		"else setenv getcmd tftp; setenv autoload no; fi\0"            \
	"netboot=echo Booting from net ...; "                                  \
		"run kernel_name; "                                            \
		"run set_getcmd; "                                             \
		"setenv bootargs; "                                            \
		"run netargs; "                                                \
		"if ${getcmd} ${kernel}; then "                                \
			"if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
				"${boot_type} ${loadaddr} - ${fdt_addr}; "     \
			"fi; "                                                 \
		"fi; "                                                         \
		"echo ... failed\0"                                            \
	"panicboot=echo No boot device !!! reset\0"                            \
	TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \

#define CONFIG_STACKSIZE		(128u * SZ_1K)

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#define CONFIG_OF_BOARD_SETUP
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE

/*
 * All the defines above are for the TQMa6 SoM
 *
 * Now include the baseboard specific configuration
 */
#ifdef CONFIG_MBA6
#include "tqma6_mba6.h"
#elif CONFIG_WRU4
#include "tqma6_wru4.h"
#else
#error "No baseboard for the TQMa6 defined!"
#endif

/* Support at least the sensor on TQMa6 SOM */
#if !defined(CONFIG_DTT_SENSORS)
#define CONFIG_DTT_SENSORS		{ 0 }
#endif

#endif /* __CONFIG_H */
Commit	Line	Data
cb07d74e MN	1	/*
	2	* Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
	3	*
	4	* Configuration settings for the TQ Systems TQMa6<Q,S> module.
	5	*
	6	* SPDX-License-Identifier: GPL-2.0+
	7	*/
	8
	9	#ifndef __CONFIG_H
	10	#define __CONFIG_H
	11
66cacc9d	12	#include <linux/kconfig.h>
1719d49c MN	13	/* SPL */
	14	/* #if defined(CONFIG_SPL_BUILD) */
	15
	16	#define CONFIG_SPL_MMC_SUPPORT
	17	#define CONFIG_SPL_SPI_SUPPORT
	18	#define CONFIG_SPL_FAT_SUPPORT
	19	#define CONFIG_SPL_EXT_SUPPORT
	20
	21	/* common IMX6 SPL configuration */
	22	#include "imx6_spl.h"
	23
	24	/* #endif */
	25
cd6ddc48 FE	26	/* place code in last 4 MiB of RAM */
	27	#if defined(CONFIG_MX6DL) \|\| defined(CONFIG_MX6S)
	28	#define CONFIG_SYS_TEXT_BASE 0x2fc00000
	29	#elif defined(CONFIG_MX6Q) \|\| defined(CONFIG_MX6D)
	30	#define CONFIG_SYS_TEXT_BASE 0x4fc00000
	31	#endif
	32
cb07d74e	33	#include "mx6_common.h"
cb07d74e	34
cb07d74e MN	35	#if defined(CONFIG_MX6DL) \|\| defined(CONFIG_MX6S)
	36	#define PHYS_SDRAM_SIZE (512u * SZ_1M)
	37	#elif defined(CONFIG_MX6Q) \|\| defined(CONFIG_MX6D)
	38	#define PHYS_SDRAM_SIZE (1024u * SZ_1M)
	39	#endif
	40
cb07d74e MN	41	#define CONFIG_BOARD_EARLY_INIT_F
	42	#define CONFIG_BOARD_LATE_INIT
	43
cb07d74e MN	44	#define CONFIG_MXC_UART
	45
	46	/* SPI */
	47	#define CONFIG_CMD_SPI
	48	#define CONFIG_MXC_SPI
	49
	50	/* SPI Flash */
cb07d74e	51
52835468 MN	52	#define TQMA6_SPI_FLASH_SECTOR_SIZE SZ_64K
52835468 MN	53
cb07d74e MN	54	#define CONFIG_CMD_SF
cb07d74e MN	55	#define CONFIG_SF_DEFAULT_BUS 0
1719d49c	56	#define CONFIG_SF_DEFAULT_CS 0
cb07d74e MN	57	#define CONFIG_SF_DEFAULT_SPEED 50000000
	58	#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
	59
	60	/* I2C Configs */
	61	#define CONFIG_CMD_I2C
	62	#define CONFIG_SYS_I2C
	63	#define CONFIG_SYS_I2C_MXC
03544c66 AA	64	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
03544c66 AA	65	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
f8cb101e	66	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
cb07d74e MN	67	#define CONFIG_I2C_MULTI_BUS
	68	#define CONFIG_SYS_I2C_SPEED 100000
	69
	70	/* I2C SYSMON (LM75) */
	71	#define CONFIG_DTT_LM75
cb07d74e MN	72	#define CONFIG_DTT_MAX_TEMP 70
	73	#define CONFIG_DTT_MIN_TEMP -30
	74	#define CONFIG_DTT_HYSTERESIS 3
	75	#define CONFIG_CMD_DTT
	76
	77	/* I2C EEPROM (M24C64) */
	78	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	79	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	80	#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS 5 /* 32 Bytes */
	81	#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS 20
	82	#define CONFIG_CMD_EEPROM
	83
	84	#define CONFIG_POWER
	85	#define CONFIG_POWER_I2C
	86	#define CONFIG_POWER_PFUZE100
	87	#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
	88	#define TQMA6_PFUZE100_I2C_BUS 2
	89
	90	/* MMC Configs */
cb07d74e MN	91	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
cb07d74e MN	92
cb07d74e MN	93	/* USB Configs */
	94	#define CONFIG_CMD_USB
	95	#define CONFIG_USB_EHCI
	96	#define CONFIG_USB_EHCI_MX6
	97	#define CONFIG_USB_STORAGE
	98	#define CONFIG_USB_HOST_ETHER
	99	#define CONFIG_USB_ETHER_SMSC95XX
cb07d74e	100	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
911b5ea5 SR	101	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
911b5ea5 SR	102	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
cb07d74e	103
cb07d74e MN	104	#define CONFIG_CMD_PING
	105	#define CONFIG_CMD_DHCP
	106	#define CONFIG_CMD_MII
cb07d74e MN	107
	108	#define CONFIG_FEC_MXC
	109	#define IMX_FEC_BASE ENET_BASE_ADDR
	110	#define CONFIG_PHYLIB
	111	#define CONFIG_MII
	112
cb07d74e MN	113	#define CONFIG_ARP_TIMEOUT 200UL
	114	/* Network config - Allow larger/faster download for TFTP/NFS */
	115	#define CONFIG_IP_DEFRAG
	116	#define CONFIG_TFTP_BLOCKSIZE 4096
	117	#define CONFIG_NFS_READ_SIZE 4096
	118
cb07d74e	119	/* Command definition */
cb07d74e	120	#define CONFIG_CMD_BMODE
cb07d74e	121
cb07d74e MN	122	#define CONFIG_ENV_SIZE (SZ_8K)
	123	/* Size of malloc() pool */
	124	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * SZ_1M)
	125
	126	#if defined(CONFIG_TQMA6X_MMC_BOOT)
	127
	128	#define CONFIG_ENV_IS_IN_MMC
	129	#define TQMA6_UBOOT_OFFSET SZ_1K
	130	#define TQMA6_UBOOT_SECTOR_START 0x2
	131	#define TQMA6_UBOOT_SECTOR_COUNT 0x7fe
	132
	133	#define CONFIG_ENV_OFFSET SZ_1M
	134	#define CONFIG_SYS_MMC_ENV_DEV 0
	135
	136	#define TQMA6_FDT_OFFSET (2 * SZ_1M)
	137	#define TQMA6_FDT_SECTOR_START 0x1000
	138	#define TQMA6_FDT_SECTOR_COUNT 0x800
	139
	140	#define TQMA6_KERNEL_SECTOR_START 0x2000
	141	#define TQMA6_KERNEL_SECTOR_COUNT 0x2000
	142
	143	#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
	144	"uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0" \
	145	"uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \
	146	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \
	147	"fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \
	148	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \
	149	"kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \
	150	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	151	"loadimage=mmc dev ${mmcdev}; " \
	152	"mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0" \
	153	"loadfdt=mmc dev ${mmcdev}; " \
	154	"mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0" \
	155	"update_uboot=if tftp ${uboot}; then " \
	156	"if itest ${filesize} > 0; then " \
	157	"mmc dev ${mmcdev}; mmc rescan; " \
	158	"setexpr blkc ${filesize} / 0x200; " \
	159	"setexpr blkc ${blkc} + 1; " \
	160	"if itest ${blkc} <= ${uboot_size}; then " \
	161	"mmc write ${loadaddr} ${uboot_start} " \
	162	"${blkc}; " \
	163	"fi; " \
	164	"fi; fi; " \
	165	"setenv filesize; setenv blkc \0" \
	166	"update_kernel=run kernel_name; " \
	167	"if tftp ${kernel}; then " \
	168	"if itest ${filesize} > 0; then " \
	169	"mmc dev ${mmcdev}; mmc rescan; " \
	170	"setexpr blkc ${filesize} / 0x200; " \
	171	"setexpr blkc ${blkc} + 1; " \
	172	"if itest ${blkc} <= ${kernel_size}; then " \
	173	"mmc write ${loadaddr} " \
	174	"${kernel_start} ${blkc}; " \
	175	"fi; " \
	176	"fi; " \
	177	"fi; " \
	178	"setenv filesize; setenv blkc \0" \
	179	"update_fdt=if tftp ${fdt_file}; then " \
	180	"if itest ${filesize} > 0; then " \
	181	"mmc dev ${mmcdev}; mmc rescan; " \
	182	"setexpr blkc ${filesize} / 0x200; " \
	183	"setexpr blkc ${blkc} + 1; " \
	184	"if itest ${blkc} <= ${fdt_size}; then " \
	185	"mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
186	"fi; " \
187	"fi; fi; " \
188	"setenv filesize; setenv blkc \0" \
189
190	#define CONFIG_BOOTCOMMAND \
191	"run mmcboot; run netboot; run panicboot"
192
193	#elif defined(CONFIG_TQMA6X_SPI_BOOT)
194
cb07d74e MN	195	#define TQMA6_UBOOT_OFFSET 0x400
	196	#define TQMA6_UBOOT_SECTOR_START 0x0
	197	/* max u-boot size: 512k */
52835468	198	#define TQMA6_UBOOT_SECTOR_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE
cb07d74e MN	199	#define TQMA6_UBOOT_SECTOR_COUNT 0x8
	200	#define TQMA6_UBOOT_SIZE (TQMA6_UBOOT_SECTOR_SIZE * \
	201	TQMA6_UBOOT_SECTOR_COUNT)
	202
	203	#define CONFIG_ENV_IS_IN_SPI_FLASH
	204	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	205	#define CONFIG_ENV_OFFSET (TQMA6_UBOOT_SIZE)
52835468	206	#define CONFIG_ENV_SECT_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE
cb07d74e MN	207	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
	208	CONFIG_ENV_SECT_SIZE)
	209
	210	#define CONFIG_ENV_SPI_BUS (CONFIG_SF_DEFAULT_BUS)
	211	#define CONFIG_ENV_SPI_CS (CONFIG_SF_DEFAULT_CS)
	212	#define CONFIG_ENV_SPI_MAX_HZ (CONFIG_SF_DEFAULT_SPEED)
	213	#define CONFIG_ENV_SPI_MODE (CONFIG_SF_DEFAULT_MODE)
	214
	215	#define TQMA6_FDT_OFFSET (CONFIG_ENV_OFFSET_REDUND + \
	216	CONFIG_ENV_SECT_SIZE)
52835468	217	#define TQMA6_FDT_SECT_SIZE (TQMA6_SPI_FLASH_SECTOR_SIZE)
cb07d74e MN	218
	219	#define TQMA6_FDT_SECTOR_START 0x0a /* 8 Sector u-boot, 2 Sector env */
	220	#define TQMA6_FDT_SECTOR_COUNT 0x01
	221
	222	#define TQMA6_KERNEL_SECTOR_START 0x10
	223	#define TQMA6_KERNEL_SECTOR_COUNT 0x60
	224
	225	#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
	226	"mmcblkdev=0\0" \
	227	"uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0" \
	228	"uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \
	229	"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \
	230	"fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \
	231	"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \
	232	"kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \
	233	"update_uboot=if tftp ${uboot}; then " \
	234	"if itest ${filesize} > 0; then " \
	235	"setexpr blkc ${filesize} + " \
	236	__stringify(TQMA6_UBOOT_OFFSET) "; " \
	237	"setexpr size ${uboot_sectors} * " \
52835468	238	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	239	"if itest ${blkc} <= ${size}; then " \
	240	"sf probe; " \
	241	"sf erase 0 ${size}; " \
	242	"sf write ${loadaddr} ${uboot_offset} " \
	243	"${filesize}; " \
	244	"fi; " \
	245	"fi; fi; " \
	246	"setenv filesize 0; setenv blkc; setenv size \0" \
	247	"update_kernel=run kernel_name; if tftp ${kernel}; then " \
	248	"if itest ${filesize} > 0; then " \
	249	"setexpr size ${kernel_sectors} * " \
52835468	250	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	251	"setexpr offset ${kernel_start} * " \
52835468	252	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	253	"if itest ${filesize} <= ${size}; then " \
	254	"sf probe; " \
	255	"sf erase ${offset} ${size}; " \
	256	"sf write ${loadaddr} ${offset} " \
	257	"${filesize}; " \
	258	"fi; " \
	259	"fi; fi; " \
	260	"setenv filesize 0; setenv size ; setenv offset\0" \
	261	"update_fdt=if tftp ${fdt_file}; then " \
	262	"if itest ${filesize} > 0; then " \
	263	"setexpr size ${fdt_sectors} * " \
52835468	264	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	265	"setexpr offset ${fdt_start} * " \
52835468	266	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	267	"if itest ${filesize} <= ${size}; then " \
	268	"sf probe; " \
	269	"sf erase ${offset} ${size}; " \
	270	"sf write ${loadaddr} ${offset} " \
	271	"${filesize}; " \
	272	"fi; " \
	273	"fi; fi; " \
	274	"setenv filesize 0; setenv size ; setenv offset\0" \
	275	"loadimage=sf probe; " \
	276	"setexpr size ${kernel_sectors} * " \
52835468	277	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	278	"setexpr offset ${kernel_start} * " \
52835468	279	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	280	"sf read ${loadaddr} ${offset} ${size}; " \
	281	"setenv size ; setenv offset\0" \
	282	"loadfdt=sf probe; " \
	283	"setexpr size ${fdt_sectors} * " \
52835468	284	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e	285	"setexpr offset ${fdt_start} * " \
52835468	286	__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
cb07d74e MN	287	"sf read ${${fdt_addr}} ${offset} ${size}; " \
	288	"setenv size ; setenv offset\0" \
	289
	290
	291	#define CONFIG_BOOTCOMMAND \
	292	"sf probe; run mmcboot; run netboot; run panicboot" \
	293
	294	#else
	295
	296	#error "need to define boot source"
	297
	298	#endif
	299
	300	/* 128 MiB offset as in ARM related docu for linux suggested */
	301	#define TQMA6_FDT_ADDRESS 0x18000000
	302
	303	#define CONFIG_EXTRA_ENV_SETTINGS \
	304	"board=tqma6\0" \
	305	"uimage=uImage\0" \
	306	"zimage=zImage\0" \
	307	"boot_type=bootz\0" \
	308	"kernel_name=if test \"${boot_type}\" != bootz; then " \
	309	"setenv kernel ${uimage}; " \
	310	"else setenv kernel ${zimage}; fi\0" \
	311	"uboot=u-boot.imx\0" \
	312	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
	313	"fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0" \
	314	"console=" CONFIG_CONSOLE_DEV "\0" \
	315	"fdt_high=0xffffffff\0" \
	316	"initrd_high=0xffffffff\0" \
	317	"addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
	318	"addfb=setenv bootargs ${bootargs} " \
	319	"imx-fbdev.legacyfb_depth=32 consoleblank=0\0" \
	320	"mmcpart=2\0" \
	321	"mmcblkdev=0\0" \
	322	"mmcargs=run addmmc addtty addfb\0" \
	323	"addmmc=setenv bootargs ${bootargs} " \
	324	"root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0" \
	325	"mmcboot=echo Booting from mmc ...; " \
	326	"setenv bootargs; " \
	327	"run mmcargs; " \
	328	"run loadimage; " \
	329	"if run loadfdt; then " \
	330	"echo boot device tree kernel ...; " \
	331	"${boot_type} ${loadaddr} - ${fdt_addr}; " \
	332	"else " \
	333	"${boot_type}; " \
	334	"fi;\0" \
	335	"setenv bootargs \0" \
	336	"netdev=eth0\0" \
	337	"rootpath=/srv/nfs/tqma6\0" \
	338	"ipmode=static\0" \
	339	"netargs=run addnfs addip addtty addfb\0" \
	340	"addnfs=setenv bootargs ${bootargs} " \
	341	"root=/dev/nfs rw " \
	342	"nfsroot=${serverip}:${rootpath},v3,tcp;\0" \
	343	"addip_static=setenv bootargs ${bootargs} " \
	344	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \
	345	"${hostname}:${netdev}:off\0" \
	346	"addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0" \
	347	"addip=if test \"${ipmode}\" != static; then " \
	348	"run addip_dynamic; else run addip_static; fi\0" \
	349	"set_getcmd=if test \"${ipmode}\" != static; then " \
	350	"setenv getcmd dhcp; setenv autoload yes; " \
351	"else setenv getcmd tftp; setenv autoload no; fi\0" \
352	"netboot=echo Booting from net ...; " \
353	"run kernel_name; " \
354	"run set_getcmd; " \
355	"setenv bootargs; " \
356	"run netargs; " \
357	"if ${getcmd} ${kernel}; then " \
358	"if ${getcmd} ${fdt_addr} ${fdt_file}; then " \
359	"${boot_type} ${loadaddr} - ${fdt_addr}; " \
360	"fi; " \
361	"fi; " \
362	"echo ... failed\0" \
363	"panicboot=echo No boot device !!! reset\0" \
364	TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
365
cb07d74e MN	366	#define CONFIG_STACKSIZE (128u * SZ_1K)
	367
	368	/* Physical Memory Map */
	369	#define CONFIG_NR_DRAM_BANKS 1
	370	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
	371
	372	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	373	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	374	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
	375
	376	#define CONFIG_SYS_INIT_SP_OFFSET \
	377	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	378	#define CONFIG_SYS_INIT_SP_ADDR \
	379	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
	380
cb07d74e MN	381	#define CONFIG_OF_BOARD_SETUP
	382	#define CONFIG_FIT
	383	#define CONFIG_FIT_VERBOSE
	384
6b396b31 SR	385	/*
	386	* All the defines above are for the TQMa6 SoM
	387	*
	388	* Now include the baseboard specific configuration
	389	*/
	390	#ifdef CONFIG_MBA6
	391	#include "tqma6_mba6.h"
452308c0 SR	392	#elif CONFIG_WRU4
452308c0 SR	393	#include "tqma6_wru4.h"
6b396b31 SR	394	#else
	395	#error "No baseboard for the TQMa6 defined!"
	396	#endif
	397
	398	/* Support at least the sensor on TQMa6 SOM */
	399	#if !defined(CONFIG_DTT_SENSORS)
	400	#define CONFIG_DTT_SENSORS { 0 }
	401	#endif
	402
cb07d74e	403	#endif /* __CONFIG_H */