[people/ms/u-boot.git] / include / configs / woodburn_common.h

/*
 * (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
 *
 * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
 *
 * Configuration for the woodburn board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __WOODBURN_COMMON_CONFIG_H
#define __WOODBURN_COMMON_CONFIG_H

#include <asm/arch/imx-regs.h>

 /* High Level Configuration Options */
#define CONFIG_MX35
#define CONFIG_MX35_HCLK_FREQ	24000000
#define CONFIG_SYS_FSL_CLK

#define CONFIG_SYS_DCACHE_OFF

/* Only in case the value is not present in mach-types.h */
#ifndef MACH_TYPE_FLEA3
#define MACH_TYPE_FLEA3                3668
#endif

#define CONFIG_MACH_TYPE		MACH_TYPE_FLEA3

/* This is required to setup the ESDC controller */

#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG

/*
 * Size of malloc() pool
 */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)

/*
 * Hardware drivers
 */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_SPD_BUS_NUM		0
#define CONFIG_MXC_SPI
#define CONFIG_MXC_GPIO

/* PMIC Controller */
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_FSL
#define CONFIG_POWER_FSL_MC13892
#define CONFIG_SYS_FSL_PMIC_I2C_ADDR	0x8
#define CONFIG_RTC_MC13XXX

/* mmc driver */
#define CONFIG_GENERIC_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR	0
#define CONFIG_SYS_FSL_ESDHC_NUM	1

/*
 * UART (console)
 */
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE	UART1_BASE

/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX	1
#define CONFIG_BAUDRATE		115200

/*
 * Command definition
 */
#define CONFIG_CMD_DATE
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_DNS

#define CONFIG_CMD_NAND

#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION

#define CONFIG_MXC_GPIO

#define CONFIG_NET_RETRY_COUNT	100


#define CONFIG_LOADADDR		0x80800000	/* loadaddr env var */

/*
 * Ethernet on SOC (FEC)
 */
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE	FEC_BASE_ADDR
#define CONFIG_PHYLIB
#define CONFIG_PHY_MICREL
#define CONFIG_FEC_MXC_PHYADDR	0x1

#define CONFIG_MII
#define CONFIG_DISCOVER_PHY

#define CONFIG_ARP_TIMEOUT	200UL

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP	/* undef to save memory */
#define CONFIG_CMDLINE_EDITING

#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

#define CONFIG_SYS_MEMTEST_START	0	/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x10000

#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

/*
 * Stack sizes
 *
 * The stack sizes are set up in start.S using the settings below
 */
#define CONFIG_STACKSIZE	(128 * 1024)	/* regular stack */

/*
 * Physical Memory Map
 */
#define CONFIG_NR_DRAM_BANKS	1
#define PHYS_SDRAM_1		CSD0_BASE_ADDR
#define PHYS_SDRAM_1_SIZE	(256 * 1024 * 1024)

#define CONFIG_SYS_SDRAM_BASE		CSD0_BASE_ADDR

#define CONFIG_SYS_GBL_DATA_OFFSET	(LOW_LEVEL_SRAM_STACK - \
						IRAM_BASE_ADDR - \
						GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR		(IRAM_BASE_ADDR + \
					CONFIG_SYS_GBL_DATA_OFFSET)

/*
 * MTD Command for mtdparts
 */
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE
#define CONFIG_FLASH_CFI_MTD
#define CONFIG_MTD_PARTITIONS
#define MTDIDS_DEFAULT		"nand0=mxc_nand,nor0=physmap-flash.0"
#define MTDPARTS_DEFAULT	"mtdparts=mxc_nand:50m(root1)," \
				"32m(rootfb)," \
				"64m(pcache)," \
				"64m(app1)," \
				"10m(app2),-(spool);" \
				"physmap-flash.0:512k(u-boot),64k(env1)," \
				"64k(env2),3776k(kernel1),3776k(kernel2)"

/*
 * FLASH and environment organization
 */
#define CONFIG_SYS_FLASH_BASE		CS0_BASE_ADDR
#define CONFIG_SYS_MAX_FLASH_BANKS 1	/* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512	/* max number of sectors on one chip */
/* Monitor at beginning of flash */
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)

#define CONFIG_ENV_SECT_SIZE	(128 * 1024)
#define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
				CONFIG_SYS_MONITOR_LEN)

#define CONFIG_ENV_IS_IN_FLASH

/*
 * CFI FLASH driver setup
 */
#define CONFIG_SYS_FLASH_CFI		/* Flash memory is CFI compliant */
#define CONFIG_FLASH_CFI_DRIVER

/* A non-standard buffered write algorithm */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* faster */
#define CONFIG_SYS_FLASH_PROTECTION	/* Use hardware sector protection */

/*
 * NAND FLASH driver setup
 */
#define CONFIG_NAND_MXC
#define CONFIG_NAND_MXC_V1_1
#define CONFIG_MXC_NAND_REGS_BASE	(NFC_BASE_ADDR)
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		(NFC_BASE_ADDR)
#define CONFIG_MXC_NAND_HWECC
#define CONFIG_SYS_NAND_LARGEPAGE

#if 0
#define CONFIG_MTD_DEBUG
#define CONFIG_MTD_DEBUG_VERBOSE	7
#endif
#define CONFIG_SYS_NAND_ONFI_DETECTION

/*
 * Default environment and default scripts
 * to update uboot and load kernel
 */

#define CONFIG_HOSTNAME woodburn
#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
	"addip_sta=setenv bootargs ${bootargs} "			\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"		\
	"addip=if test -n ${ipdyn};then run addip_dyn;"			\
		"else run addip_sta;fi\0"	\
	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
	"addtty=setenv bootargs ${bootargs}"				\
		" console=ttymxc0,${baudrate}\0"			\
	"addmisc=setenv bootargs ${bootargs} ${misc}\0"			\
	"loadaddr=80800000\0"						\
	"kernel_addr_r=80800000\0"					\
	"hostname=" __stringify(CONFIG_HOSTNAME) "\0"			\
	"bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"		\
	"ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"	\
	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
		"bootm ${kernel_addr}\0"				\
	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
		"run nfsargs addip addtty addmtd addmisc;"		\
		"bootm ${kernel_addr_r}\0"				\
	"net_self_load=tftp ${kernel_addr_r} ${bootfile};"		\
		"tftp ${ramdisk_addr_r} ${ramdisk_file};\0"		\
	"net_self=if run net_self_load;then "				\
		"run ramargs addip addtty addmtd addmisc;"		\
		"bootm ${kernel_addr_r} ${ramdisk_addr_r};"		\
		"else echo Images not loades;fi\0"			\
	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"		\
	"load=tftp ${loadaddr} ${u-boot}\0"				\
	"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"		\
	"update=protect off ${uboot_addr} +80000;"			\
		"erase ${uboot_addr} +80000;"				\
		"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"		\
	"upd=if run load;then echo Updating u-boot;if run update;"	\
		"then echo U-Boot updated;"				\
			"else echo Error updating u-boot !;"		\
			"echo Board without bootloader !!;"		\
		"fi;"							\
		"else echo U-Boot not downloaded..exiting;fi\0"		\
	"bootcmd=run net_nfs\0"

#endif				/* __CONFIG_H */
Commit	Line	Data
d81b27a2 SB	1	/*
	2	* (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
	3	*
	4	* (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
	5	*
	6	* Configuration for the woodburn board.
	7	*
3765b3e7	8	* SPDX-License-Identifier: GPL-2.0+
d81b27a2 SB	9	*/
	10
	11	#ifndef __WOODBURN_COMMON_CONFIG_H
	12	#define __WOODBURN_COMMON_CONFIG_H
	13
	14	#include <asm/arch/imx-regs.h>
	15
	16	/* High Level Configuration Options */
d81b27a2 SB	17	#define CONFIG_MX35
d81b27a2 SB	18	#define CONFIG_MX35_HCLK_FREQ 24000000
18fb0e3c	19	#define CONFIG_SYS_FSL_CLK
d81b27a2 SB	20
d81b27a2 SB	21	#define CONFIG_SYS_DCACHE_OFF
d81b27a2	22
d81b27a2 SB	23	/* Only in case the value is not present in mach-types.h */
	24	#ifndef MACH_TYPE_FLEA3
	25	#define MACH_TYPE_FLEA3 3668
	26	#endif
	27
	28	#define CONFIG_MACH_TYPE MACH_TYPE_FLEA3
	29
	30	/* This is required to setup the ESDC controller */
	31
	32	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
	33	#define CONFIG_REVISION_TAG
	34	#define CONFIG_SETUP_MEMORY_TAGS
	35	#define CONFIG_INITRD_TAG
	36
	37	/*
	38	* Size of malloc() pool
	39	*/
	40	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
	41
	42	/*
	43	* Hardware drivers
	44	*/
b089d039	45	#define CONFIG_SYS_I2C
b089d039	46	#define CONFIG_SYS_I2C_MXC
03544c66 AA	47	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
03544c66 AA	48	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
f8cb101e	49	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
b089d039	50	#define CONFIG_SYS_SPD_BUS_NUM 0
d81b27a2 SB	51	#define CONFIG_MXC_SPI
	52	#define CONFIG_MXC_GPIO
	53
	54	/* PMIC Controller */
05a860c2 SB	55	#define CONFIG_POWER
	56	#define CONFIG_POWER_I2C
	57	#define CONFIG_POWER_FSL
913702ca	58	#define CONFIG_POWER_FSL_MC13892
d81b27a2 SB	59	#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
	60	#define CONFIG_RTC_MC13XXX
	61
d81b27a2	62	/* mmc driver */
d81b27a2 SB	63	#define CONFIG_GENERIC_MMC
	64	#define CONFIG_FSL_ESDHC
	65	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	66	#define CONFIG_SYS_FSL_ESDHC_NUM 1
	67
	68	/*
	69	* UART (console)
	70	*/
	71	#define CONFIG_MXC_UART
	72	#define CONFIG_MXC_UART_BASE UART1_BASE
	73
	74	/* allow to overwrite serial and ethaddr */
	75	#define CONFIG_ENV_OVERWRITE
	76	#define CONFIG_CONS_INDEX 1
	77	#define CONFIG_BAUDRATE 115200
	78
	79	/*
	80	* Command definition
	81	*/
d81b27a2	82	#define CONFIG_CMD_DATE
d81b27a2 SB	83	#define CONFIG_BOOTP_SUBNETMASK
	84	#define CONFIG_BOOTP_GATEWAY
	85	#define CONFIG_BOOTP_DNS
	86
	87	#define CONFIG_CMD_NAND
d81b27a2	88
d81b27a2 SB	89	#define CONFIG_DOS_PARTITION
d81b27a2 SB	90	#define CONFIG_EFI_PARTITION
d81b27a2	91
d81b27a2 SB	92	#define CONFIG_MXC_GPIO
	93
	94	#define CONFIG_NET_RETRY_COUNT 100
	95
d81b27a2 SB	96
	97	#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
	98
d81b27a2 SB	99	/*
	100	* Ethernet on SOC (FEC)
	101	*/
	102	#define CONFIG_FEC_MXC
	103	#define IMX_FEC_BASE FEC_BASE_ADDR
	104	#define CONFIG_PHYLIB
	105	#define CONFIG_PHY_MICREL
	106	#define CONFIG_FEC_MXC_PHYADDR 0x1
	107
	108	#define CONFIG_MII
	109	#define CONFIG_DISCOVER_PHY
	110
	111	#define CONFIG_ARP_TIMEOUT 200UL
	112
	113	/*
	114	* Miscellaneous configurable options
	115	*/
	116	#define CONFIG_SYS_LONGHELP /* undef to save memory */
d81b27a2	117	#define CONFIG_CMDLINE_EDITING
d81b27a2 SB	118
	119	#define CONFIG_AUTO_COMPLETE
	120	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	121	/* Print Buffer Size */
	122	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	123	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	124	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
	125
	126	#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
	127	#define CONFIG_SYS_MEMTEST_END 0x10000
	128
d81b27a2 SB	129	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
d81b27a2 SB	130
d81b27a2 SB	131	/*
	132	* Stack sizes
	133	*
	134	* The stack sizes are set up in start.S using the settings below
	135	*/
	136	#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
	137
	138	/*
	139	* Physical Memory Map
	140	*/
	141	#define CONFIG_NR_DRAM_BANKS 1
	142	#define PHYS_SDRAM_1 CSD0_BASE_ADDR
	143	#define PHYS_SDRAM_1_SIZE (256 * 1024 * 1024)
	144
	145	#define CONFIG_SYS_SDRAM_BASE CSD0_BASE_ADDR
	146
	147	#define CONFIG_SYS_GBL_DATA_OFFSET (LOW_LEVEL_SRAM_STACK - \
	148	IRAM_BASE_ADDR - \
	149	GENERATED_GBL_DATA_SIZE)
	150	#define CONFIG_SYS_INIT_SP_ADDR (IRAM_BASE_ADDR + \
	151	CONFIG_SYS_GBL_DATA_OFFSET)
	152
	153	/*
	154	* MTD Command for mtdparts
	155	*/
	156	#define CONFIG_CMD_MTDPARTS
	157	#define CONFIG_MTD_DEVICE
	158	#define CONFIG_FLASH_CFI_MTD
	159	#define CONFIG_MTD_PARTITIONS
	160	#define MTDIDS_DEFAULT "nand0=mxc_nand,nor0=physmap-flash.0"
	161	#define MTDPARTS_DEFAULT "mtdparts=mxc_nand:50m(root1)," \
	162	"32m(rootfb)," \
	163	"64m(pcache)," \
	164	"64m(app1)," \
	165	"10m(app2),-(spool);" \
	166	"physmap-flash.0:512k(u-boot),64k(env1)," \
	167	"64k(env2),3776k(kernel1),3776k(kernel2)"
	168
	169	/*
	170	* FLASH and environment organization
	171	*/
	172	#define CONFIG_SYS_FLASH_BASE CS0_BASE_ADDR
	173	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	174	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
	175	/* Monitor at beginning of flash */
	176	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	177	#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
	178
	179	#define CONFIG_ENV_SECT_SIZE (128 * 1024)
	180	#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
	181
	182	/* Address and size of Redundant Environment Sector */
	183	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
	184	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	185
	186	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
	187	CONFIG_SYS_MONITOR_LEN)
	188
	189	#define CONFIG_ENV_IS_IN_FLASH
	190
	191	/*
	192	* CFI FLASH driver setup
	193	*/
	194	#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
195	#define CONFIG_FLASH_CFI_DRIVER
196
197	/* A non-standard buffered write algorithm */
198	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* faster */
199	#define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */
200
201	/*
202	* NAND FLASH driver setup
203	*/
204	#define CONFIG_NAND_MXC
205	#define CONFIG_NAND_MXC_V1_1
206	#define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR)
207	#define CONFIG_SYS_MAX_NAND_DEVICE 1
208	#define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR)
209	#define CONFIG_MXC_NAND_HWECC
210	#define CONFIG_SYS_NAND_LARGEPAGE
211
212	#if 0
213	#define CONFIG_MTD_DEBUG
214	#define CONFIG_MTD_DEBUG_VERBOSE 7
215	#endif
216	#define CONFIG_SYS_NAND_ONFI_DETECTION
217
218	/*
219	* Default environment and default scripts
220	* to update uboot and load kernel
221	*/
d81b27a2 SB	222
	223	#define CONFIG_HOSTNAME woodburn
	224	#define CONFIG_EXTRA_ENV_SETTINGS \
	225	"netdev=eth0\0" \
	226	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	227	"nfsroot=${serverip}:${rootpath}\0" \
	228	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	229	"addip_sta=setenv bootargs ${bootargs} " \
	230	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	231	":${hostname}:${netdev}:off panic=1\0" \
	232	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
	233	"addip=if test -n ${ipdyn};then run addip_dyn;" \
	234	"else run addip_sta;fi\0" \
	235	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
	236	"addtty=setenv bootargs ${bootargs}" \
	237	" console=ttymxc0,${baudrate}\0" \
	238	"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
	239	"loadaddr=80800000\0" \
	240	"kernel_addr_r=80800000\0" \
4a8c3f69 AG	241	"hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
	242	"bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
	243	"ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0" \
d81b27a2 SB	244	"flash_self=run ramargs addip addtty addmtd addmisc;" \
	245	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	246	"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
	247	"bootm ${kernel_addr}\0" \
	248	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
	249	"run nfsargs addip addtty addmtd addmisc;" \
	250	"bootm ${kernel_addr_r}\0" \
	251	"net_self_load=tftp ${kernel_addr_r} ${bootfile};" \
	252	"tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \
	253	"net_self=if run net_self_load;then " \
	254	"run ramargs addip addtty addmtd addmisc;" \
	255	"bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
	256	"else echo Images not loades;fi\0" \
4a8c3f69	257	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \
d81b27a2	258	"load=tftp ${loadaddr} ${u-boot}\0" \
4a8c3f69	259	"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \
d81b27a2 SB	260	"update=protect off ${uboot_addr} +80000;" \
	261	"erase ${uboot_addr} +80000;" \
	262	"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \
	263	"upd=if run load;then echo Updating u-boot;if run update;" \
	264	"then echo U-Boot updated;" \
	265	"else echo Error updating u-boot !;" \
	266	"echo Board without bootloader !!;" \
	267	"fi;" \
	268	"else echo U-Boot not downloaded..exiting;fi\0" \
	269	"bootcmd=run net_nfs\0"
	270
	271	#endif /* __CONFIG_H */