[people/ms/u-boot.git] / include / configs / xpedite520x.h

/*
 * Copyright 2008 Extreme Engineering Solutions, Inc.
 * Copyright 2004-2008 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * xpedite520x board configuration file
 */
#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_XPEDITE5200	1
#define CONFIG_SYS_BOARD_NAME	"XPedite5200"
#define CONFIG_SYS_FORM_PMC_XMC	1
#define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xfff80000
#endif

#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
#define CONFIG_PCI1		1	/* PCI controller 1 */
#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */

/*
 * DDR config
 */
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
#define SPD_EEPROM_ADDRESS		0x54
#define CONFIG_DIMM_SLOTS_PER_CTLR	1
#define CONFIG_CHIP_SELECTS_PER_CTRL	2
#define CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM

#define CONFIG_SYS_CLK_FREQ	66666666

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE			/* toggle L2 cache */
#define CONFIG_BTB			/* toggle branch predition */
#define CONFIG_ENABLE_36BIT_PHYS	1

#define CONFIG_SYS_CCSRBAR		0xef000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR

/*
 * Diagnostics
 */
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_SYS_MEMTEST_START	0x10000000
#define CONFIG_SYS_MEMTEST_END		0x20000000
#define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
					 CONFIG_SYS_POST_I2C)
#define I2C_ADDR_LIST			{CONFIG_SYS_I2C_MAX1237_ADDR,	\
					 CONFIG_SYS_I2C_EEPROM_ADDR,	\
					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
					 CONFIG_SYS_I2C_PCA953X_ADDR1,	\
					 CONFIG_SYS_I2C_RTC_ADDR}

/*
 * Memory map
 * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
 * 0x8000_0000	0xbfff_ffff	PCI1 Mem		1G non-cacheable
 * 0xe000_0000	0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
 * 0xe800_0000	0xe87f_ffff	PCI1 IO			8M non-cacheable
 * 0xef00_0000	0xef0f_ffff	CCSR/IMMR		1M non-cacheable
 * 0xef80_0000	0xef8f_ffff	NAND Flash		1M non-cacheable
 * 0xf800_0000	0xfbff_ffff	NOR Flash 2		64M non-cacheable
 * 0xfc00_0000	0xffff_ffff	NOR Flash 1		64M non-cacheable
 */

#define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)

/*
 * NAND flash configuration
 */
#define CONFIG_SYS_NAND_BASE		0xef800000
#define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_NAND_ACTL
#define CONFIG_SYS_NAND_ACTL_CLE	(1 << 3)	/* ADDR3 is CLE */
#define CONFIG_SYS_NAND_ACTL_ALE	(1 << 4)	/* ADDR4 is ALE */
#define CONFIG_SYS_NAND_ACTL_NCE	(0)		/* NCE not controlled by ADDR */
#define CONFIG_SYS_NAND_ACTL_DELAY	25

/*
 * NOR flash configuration
 */
#define CONFIG_SYS_FLASH_BASE		0xfc000000
#define CONFIG_SYS_FLASH_BASE2		0xf8000000
#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
						  {0xfbf40000, 0xc0000} }
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

/*
 * Chip select configuration
 */
/* NOR Flash 0 on CS0 */
#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
				 BR_PS_16		| \
				 BR_V)
#define CONFIG_SYS_OR0_PRELIM	(OR_AM_64MB		| \
				 OR_GPCM_ACS_DIV4	| \
				 OR_GPCM_SCY_8)

/* NOR Flash 1 on CS1 */
#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
				 BR_PS_16		| \
				 BR_V)
#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM

/* NAND flash on CS2 */
#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
				 BR_PS_8		| \
				 BR_V)

/* NAND flash on CS2 */
#define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB		| \
				 OR_GPCM_BCTLD		| \
				 OR_GPCM_CSNT		| \
				 OR_GPCM_ACS_DIV4	| \
				 OR_GPCM_SCY_4		| \
				 OR_GPCM_TRLX		| \
				 OR_GPCM_EHTR)

/* NAND flash on CS3 */
#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
				 BR_PS_8		| \
				 BR_V)
#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM

/*
 * Use L1 as initial stack
 */
#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
#define CONFIG_SYS_INIT_RAM_SIZE		0x4000

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
#define CONFIG_SYS_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

/*
 * I2C
 */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED	400000
#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100

/* I2C EEPROM */
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */

/* I2C RTC */
#define CONFIG_RTC_M41T11			1
#define CONFIG_SYS_I2C_RTC_ADDR			0x68
#define CONFIG_SYS_M41T11_BASE_YEAR		2000

/* GPIO */
#define CONFIG_PCA953X
#define CONFIG_SYS_I2C_PCA953X_ADDR0		0x18
#define CONFIG_SYS_I2C_PCA953X_ADDR1		0x19
#define CONFIG_SYS_I2C_PCA953X_ADDR		CONFIG_SYS_I2C_PCA953X_ADDR0

/* PCA957 @ 0x18 */
#define CONFIG_SYS_PCA953X_BRD_CFG0		0x01
#define CONFIG_SYS_PCA953X_BRD_CFG1		0x02
#define CONFIG_SYS_PCA953X_BRD_CFG2		0x04
#define CONFIG_SYS_PCA953X_XMC_ROOT0		0x08
#define CONFIG_SYS_PCA953X_FLASH_PASS_CS	0x10
#define CONFIG_SYS_PCA953X_NVM_WP		0x20
#define CONFIG_SYS_PCA953X_MONARCH		0x40
#define CONFIG_SYS_PCA953X_EREADY		0x80

/* PCA957 @ 0x19 */
#define CONFIG_SYS_PCA953X_P14_IO0		0x01
#define CONFIG_SYS_PCA953X_P14_IO1		0x02
#define CONFIG_SYS_PCA953X_P14_IO2		0x04
#define CONFIG_SYS_PCA953X_P14_IO3		0x08
#define CONFIG_SYS_PCA953X_P14_IO4		0x10
#define CONFIG_SYS_PCA953X_P14_IO5		0x20
#define CONFIG_SYS_PCA953X_P14_IO6		0x40
#define CONFIG_SYS_PCA953X_P14_IO7		0x80

/* 12-bit ADC used to measure CPU diode */
#define CONFIG_SYS_I2C_MAX1237_ADDR		0x34

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */
#define CONFIG_SYS_PCI1_MEM_BUS		0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BUS
#define CONFIG_SYS_PCI1_MEM_SIZE	0x40000000	/* 1G */
#define CONFIG_SYS_PCI1_IO_BUS		0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS		0xe8000000
#define CONFIG_SYS_PCI1_IO_SIZE		0x00800000	/* 1M */

/*
 * Networking options
 */
#define CONFIG_TSEC_ENET		/* tsec ethernet support */
#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
#define CONFIG_MII		1	/* MII PHY management */
#define CONFIG_ETHPRIME		"eTSEC1"

#define CONFIG_TSEC1		1
#define CONFIG_TSEC1_NAME	"eTSEC1"
#define TSEC1_FLAGS		TSEC_GIGABIT
#define TSEC1_PHY_ADDR		1
#define TSEC1_PHYIDX		0
#define CONFIG_HAS_ETH0

#define CONFIG_TSEC2		1
#define CONFIG_TSEC2_NAME	"eTSEC2"
#define TSEC2_FLAGS		TSEC_GIGABIT
#define TSEC2_PHY_ADDR		2
#define TSEC2_PHYIDX		0
#define CONFIG_HAS_ETH1

#define CONFIG_TSEC3	1
#define CONFIG_TSEC3_NAME	"eTSEC3"
#define TSEC3_FLAGS		TSEC_GIGABIT
#define TSEC3_PHY_ADDR		3
#define TSEC3_PHYIDX		0
#define CONFIG_HAS_ETH2

#define CONFIG_TSEC4	1
#define CONFIG_TSEC4_NAME	"eTSEC4"
#define TSEC4_FLAGS		TSEC_GIGABIT
#define TSEC4_PHY_ADDR		4
#define TSEC4_PHYIDX		0
#define CONFIG_HAS_ETH3

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY

/*
 * Command configuration.
 */
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCA953X
#define CONFIG_CMD_PCA953X_INFO
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PCI_ENUM
#define CONFIG_CMD_REGINFO

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
#define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
#define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
#define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
#define CONFIG_PANIC_HANG			/* do not reset board on panic */
#define CONFIG_PREBOOT				/* enable preboot variable */
#define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */
#define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 16 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */

/*
 * Environment Configuration
 */
#define CONFIG_ENV_IS_IN_FLASH	1
#define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
#define CONFIG_ENV_SIZE		0x8000
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))

/*
 * Flash memory map:
 * fff80000 - ffffffff     Pri U-Boot (512 KB)
 * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
 * fff00000 - fff3ffff     Pri FDT (256KB)
 * fef00000 - ffefffff     Pri OS image (16MB)
 * fc000000 - feefffff     Pri OS Use/Filesystem (47MB)
 *
 * fbf80000 - fbffffff     Sec U-Boot (512 KB)
 * fbf40000 - fbf7ffff     Sec U-Boot Environment (256 KB)
 * fbf00000 - fbf3ffff     Sec FDT (256KB)
 * faf00000 - fbefffff     Sec OS image (16MB)
 * f8000000 - faefffff     Sec OS Use/Filesystem (47MB)
 */
#define CONFIG_UBOOT1_ENV_ADDR	__stringify(0xfff80000)
#define CONFIG_UBOOT2_ENV_ADDR	__stringify(0xfbf80000)
#define CONFIG_FDT1_ENV_ADDR	__stringify(0xfff00000)
#define CONFIG_FDT2_ENV_ADDR	__stringify(0xfbf00000)
#define CONFIG_OS1_ENV_ADDR	__stringify(0xfef00000)
#define CONFIG_OS2_ENV_ADDR	__stringify(0xfaf00000)

#define CONFIG_PROG_UBOOT1						\
	"$download_cmd $loadaddr $ubootfile; "				\
	"if test $? -eq 0; then "					\
		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
		"if test $? -ne 0; then "				\
			"echo PROGRAM FAILED; "				\
		"else; "						\
			"echo PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_UBOOT2						\
	"$download_cmd $loadaddr $ubootfile; "				\
	"if test $? -eq 0; then "					\
		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
		"if test $? -ne 0; then "				\
			"echo PROGRAM FAILED; "				\
		"else; "						\
			"echo PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_BOOT_OS_NET						\
	"$download_cmd $osaddr $osfile; "				\
	"if test $? -eq 0; then "					\
		"if test -n $fdtaddr; then "				\
			"$download_cmd $fdtaddr $fdtfile; "		\
			"if test $? -eq 0; then "			\
				"bootm $osaddr - $fdtaddr; "		\
			"else; "					\
				"echo FDT DOWNLOAD FAILED; "		\
			"fi; "						\
		"else; "						\
			"bootm $osaddr; "				\
		"fi; "							\
	"else; "							\
		"echo OS DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_OS1							\
	"$download_cmd $osaddr $osfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo OS PROGRAM FAILED; "			\
		"else; "						\
			"echo OS PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo OS DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_OS2							\
	"$download_cmd $osaddr $osfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo OS PROGRAM FAILED; "			\
		"else; "						\
			"echo OS PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo OS DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_FDT1						\
	"$download_cmd $fdtaddr $fdtfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo FDT PROGRAM FAILED; "			\
		"else; "						\
			"echo FDT PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo FDT DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_FDT2						\
	"$download_cmd $fdtaddr $fdtfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo FDT PROGRAM FAILED; "			\
		"else; "						\
			"echo FDT PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo FDT DOWNLOAD FAILED; "				\
	"fi;"

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"autoload=yes\0"						\
	"download_cmd=tftp\0"						\
	"console_args=console=ttyS0,115200\0"				\
	"root_args=root=/dev/nfs rw\0"					\
	"misc_args=ip=on\0"						\
	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
	"bootfile=/home/user/file\0"					\
	"osfile=/home/user/board.uImage\0"				\
	"fdtfile=/home/user/board.dtb\0"				\
	"ubootfile=/home/user/u-boot.bin\0"				\
	"fdtaddr=0x1e00000\0"						\
	"osaddr=0x1000000\0"						\
	"loadaddr=0x1000000\0"						\
	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
	"prog_os1="CONFIG_PROG_OS1"\0"					\
	"prog_os2="CONFIG_PROG_OS2"\0"					\
	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
	"bootcmd_flash1=run set_bootargs; "				\
		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
	"bootcmd_flash2=run set_bootargs; "				\
		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
	"bootcmd=run bootcmd_flash1\0"
#endif	/* __CONFIG_H */
Commit	Line	Data
1f03cbfa PT	1	/*
	2	* Copyright 2008 Extreme Engineering Solutions, Inc.
	3	* Copyright 2004-2008 Freescale Semiconductor, Inc.
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
1f03cbfa PT	6	*/
	7
	8	/*
c00ac259	9	* xpedite520x board configuration file
1f03cbfa PT	10	*/
	11	#ifndef __CONFIG_H
	12	#define __CONFIG_H
	13
	14	/*
	15	* High Level Configuration Options
	16	*/
1f03cbfa PT	17	#define CONFIG_XPEDITE5200 1
1f03cbfa PT	18	#define CONFIG_SYS_BOARD_NAME "XPedite5200"
92af6549	19	#define CONFIG_SYS_FORM_PMC_XMC 1
1f03cbfa	20	#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
1f03cbfa	21
2ae18241 WD	22	#ifndef CONFIG_SYS_TEXT_BASE
	23	#define CONFIG_SYS_TEXT_BASE 0xfff80000
	24	#endif
	25
1f03cbfa PT	26	#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
	27	#define CONFIG_PCI1 1 /* PCI controller 1 */
	28	#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
842033e6	29	#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
1f03cbfa	30	#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
1f03cbfa PT	31
	32	/*
	33	* DDR config
	34	*/
1f03cbfa PT	35	#undef CONFIG_FSL_DDR_INTERACTIVE
	36	#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
	37	#define CONFIG_DDR_SPD
	38	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	39	#define SPD_EEPROM_ADDRESS 0x54
1f03cbfa PT	40	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	41	#define CONFIG_CHIP_SELECTS_PER_CTRL 2
	42	#define CONFIG_DDR_ECC
	43	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	44	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	45	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	46	#define CONFIG_VERY_BIG_RAM
	47
	48	#define CONFIG_SYS_CLK_FREQ 66666666
	49
	50	/*
	51	* These can be toggled for performance analysis, otherwise use default.
	52	*/
	53	#define CONFIG_L2_CACHE /* toggle L2 cache */
	54	#define CONFIG_BTB /* toggle branch predition */
	55	#define CONFIG_ENABLE_36BIT_PHYS 1
	56
e46fedfe TT	57	#define CONFIG_SYS_CCSRBAR 0xef000000
e46fedfe TT	58	#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
1f03cbfa PT	59
	60	/*
	61	* Diagnostics
	62	*/
	63	#define CONFIG_SYS_ALT_MEMTEST
	64	#define CONFIG_SYS_MEMTEST_START 0x10000000
	65	#define CONFIG_SYS_MEMTEST_END 0x20000000
66a8b440 PT	66	#define CONFIG_POST (CONFIG_SYS_POST_MEMORY \| \
	67	CONFIG_SYS_POST_I2C)
	68	#define I2C_ADDR_LIST {CONFIG_SYS_I2C_MAX1237_ADDR, \
	69	CONFIG_SYS_I2C_EEPROM_ADDR, \
	70	CONFIG_SYS_I2C_PCA953X_ADDR0, \
	71	CONFIG_SYS_I2C_PCA953X_ADDR1, \
	72	CONFIG_SYS_I2C_RTC_ADDR}
1f03cbfa PT	73
	74	/*
	75	* Memory map
	76	* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
	77	* 0x8000_0000 0xbfff_ffff PCI1 Mem 1G non-cacheable
	78	* 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
	79	* 0xe800_0000 0xe87f_ffff PCI1 IO 8M non-cacheable
	80	* 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
	81	* 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
	82	* 0xf800_0000 0xfbff_ffff NOR Flash 2 64M non-cacheable
	83	* 0xfc00_0000 0xffff_ffff NOR Flash 1 64M non-cacheable
	84	*/
	85
202d9487	86	#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 \| LCRR_EADC_3)
1f03cbfa PT	87
	88	/*
	89	* NAND flash configuration
	90	*/
	91	#define CONFIG_SYS_NAND_BASE 0xef800000
	92	#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
	93	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	94	#define CONFIG_NAND_ACTL
	95	#define CONFIG_SYS_NAND_ACTL_CLE (1 << 3) /* ADDR3 is CLE */
	96	#define CONFIG_SYS_NAND_ACTL_ALE (1 << 4) /* ADDR4 is ALE */
	97	#define CONFIG_SYS_NAND_ACTL_NCE (0) /* NCE not controlled by ADDR */
	98	#define CONFIG_SYS_NAND_ACTL_DELAY 25
	99
	100	/*
	101	* NOR flash configuration
	102	*/
	103	#define CONFIG_SYS_FLASH_BASE 0xfc000000
	104	#define CONFIG_SYS_FLASH_BASE2 0xf8000000
	105	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
	106	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
	107	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	108	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	109	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	110	#define CONFIG_FLASH_CFI_DRIVER
	111	#define CONFIG_SYS_FLASH_CFI
5ff82100	112	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
1f03cbfa PT	113	#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
1f03cbfa PT	114	{0xfbf40000, 0xc0000} }
14d0a02a	115	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
1f03cbfa PT	116
	117	/*
	118	* Chip select configuration
	119	*/
	120	/* NOR Flash 0 on CS0 */
	121	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| \
	122	BR_PS_16 \| \
	123	BR_V)
	124	#define CONFIG_SYS_OR0_PRELIM (OR_AM_64MB \| \
	125	OR_GPCM_ACS_DIV4 \| \
	126	OR_GPCM_SCY_8)
	127
	128	/* NOR Flash 1 on CS1 */
	129	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 \| \
	130	BR_PS_16 \| \
	131	BR_V)
	132	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
	133
	134	/* NAND flash on CS2 */
	135	#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE \| \
	136	BR_PS_8 \| \
	137	BR_V)
	138
	139	/* NAND flash on CS2 */
	140	#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB \| \
	141	OR_GPCM_BCTLD \| \
	142	OR_GPCM_CSNT \| \
	143	OR_GPCM_ACS_DIV4 \| \
	144	OR_GPCM_SCY_4 \| \
	145	OR_GPCM_TRLX \| \
	146	OR_GPCM_EHTR)
	147
	148	/* NAND flash on CS3 */
	149	#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 \| \
	150	BR_PS_8 \| \
	151	BR_V)
	152	#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
	153
	154	/*
	155	* Use L1 as initial stack
	156	*/
	157	#define CONFIG_SYS_INIT_RAM_LOCK 1
	158	#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
553f0982	159	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000
1f03cbfa	160
25ddd1fb	161	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
1f03cbfa PT	162	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	163
	164	#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
	165	#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
	166
	167	/*
	168	* Serial Port
	169	*/
	170	#define CONFIG_CONS_INDEX 1
1f03cbfa PT	171	#define CONFIG_SYS_NS16550_SERIAL
	172	#define CONFIG_SYS_NS16550_REG_SIZE 1
	173	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	174	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
	175	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
	176	#define CONFIG_SYS_BAUDRATE_TABLE \
	177	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
1f03cbfa PT	178	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	179	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
	180
1f03cbfa PT	181	/*
	182	* I2C
	183	*/
00f792e0 HS	184	#define CONFIG_SYS_I2C
	185	#define CONFIG_SYS_I2C_FSL
	186	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	187	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	188	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	189	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	190	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	191	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
1f03cbfa PT	192
	193	/* I2C EEPROM */
	194	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	195	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	196	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
	197	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
	198
	199	/* I2C RTC */
	200	#define CONFIG_RTC_M41T11 1
	201	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
	202	#define CONFIG_SYS_M41T11_BASE_YEAR 2000
	203
	204	/* GPIO */
	205	#define CONFIG_PCA953X
	206	#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
	207	#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x19
	208	#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
	209
	210	/* PCA957 @ 0x18 */
	211	#define CONFIG_SYS_PCA953X_BRD_CFG0 0x01
	212	#define CONFIG_SYS_PCA953X_BRD_CFG1 0x02
	213	#define CONFIG_SYS_PCA953X_BRD_CFG2 0x04
	214	#define CONFIG_SYS_PCA953X_XMC_ROOT0 0x08
	215	#define CONFIG_SYS_PCA953X_FLASH_PASS_CS 0x10
72fb68d5	216	#define CONFIG_SYS_PCA953X_NVM_WP 0x20
1f03cbfa PT	217	#define CONFIG_SYS_PCA953X_MONARCH 0x40
	218	#define CONFIG_SYS_PCA953X_EREADY 0x80
	219
	220	/* PCA957 @ 0x19 */
	221	#define CONFIG_SYS_PCA953X_P14_IO0 0x01
	222	#define CONFIG_SYS_PCA953X_P14_IO1 0x02
	223	#define CONFIG_SYS_PCA953X_P14_IO2 0x04
	224	#define CONFIG_SYS_PCA953X_P14_IO3 0x08
	225	#define CONFIG_SYS_PCA953X_P14_IO4 0x10
	226	#define CONFIG_SYS_PCA953X_P14_IO5 0x20
	227	#define CONFIG_SYS_PCA953X_P14_IO6 0x40
	228	#define CONFIG_SYS_PCA953X_P14_IO7 0x80
	229
66a8b440 PT	230	/* 12-bit ADC used to measure CPU diode */
	231	#define CONFIG_SYS_I2C_MAX1237_ADDR 0x34
	232
1f03cbfa PT	233	/*
	234	* General PCI
	235	* Memory space is mapped 1-1, but I/O space must start from 0.
	236	*/
9660c5de PT	237	#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
9660c5de PT	238	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS
1f03cbfa	239	#define CONFIG_SYS_PCI1_MEM_SIZE 0x40000000 /* 1G */
9660c5de	240	#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
1f03cbfa PT	241	#define CONFIG_SYS_PCI1_IO_PHYS 0xe8000000
	242	#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 1M */
	243
	244	/*
	245	* Networking options
	246	*/
	247	#define CONFIG_TSEC_ENET /* tsec ethernet support */
	248	#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
1f03cbfa PT	249	#define CONFIG_MII 1 /* MII PHY management */
	250	#define CONFIG_ETHPRIME "eTSEC1"
	251
	252	#define CONFIG_TSEC1 1
	253	#define CONFIG_TSEC1_NAME "eTSEC1"
	254	#define TSEC1_FLAGS TSEC_GIGABIT
	255	#define TSEC1_PHY_ADDR 1
	256	#define TSEC1_PHYIDX 0
	257	#define CONFIG_HAS_ETH0
	258
	259	#define CONFIG_TSEC2 1
	260	#define CONFIG_TSEC2_NAME "eTSEC2"
	261	#define TSEC2_FLAGS TSEC_GIGABIT
	262	#define TSEC2_PHY_ADDR 2
	263	#define TSEC2_PHYIDX 0
	264	#define CONFIG_HAS_ETH1
	265
	266	#define CONFIG_TSEC3 1
	267	#define CONFIG_TSEC3_NAME "eTSEC3"
	268	#define TSEC3_FLAGS TSEC_GIGABIT
	269	#define TSEC3_PHY_ADDR 3
	270	#define TSEC3_PHYIDX 0
	271	#define CONFIG_HAS_ETH2
	272
	273	#define CONFIG_TSEC4 1
	274	#define CONFIG_TSEC4_NAME "eTSEC4"
	275	#define TSEC4_FLAGS TSEC_GIGABIT
	276	#define TSEC4_PHY_ADDR 4
	277	#define TSEC4_PHYIDX 0
	278	#define CONFIG_HAS_ETH3
	279
	280	/*
	281	* BOOTP options
	282	*/
	283	#define CONFIG_BOOTP_BOOTFILESIZE
	284	#define CONFIG_BOOTP_BOOTPATH
	285	#define CONFIG_BOOTP_GATEWAY
	286
	287	/*
	288	* Command configuration.
	289	*/
1f03cbfa	290	#define CONFIG_CMD_EEPROM
1f03cbfa	291	#define CONFIG_CMD_JFFS2
1f03cbfa	292	#define CONFIG_CMD_NAND
1f03cbfa PT	293	#define CONFIG_CMD_PCA953X
	294	#define CONFIG_CMD_PCA953X_INFO
	295	#define CONFIG_CMD_PCI
96d61603	296	#define CONFIG_CMD_PCI_ENUM
199e262e	297	#define CONFIG_CMD_REGINFO
1f03cbfa PT	298
	299	/*
	300	* Miscellaneous configurable options
	301	*/
	302	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	303	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
1f03cbfa PT	304	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	305	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	306	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	307	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
1f03cbfa	308	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
5be58f5f	309	#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
1f03cbfa	310	#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
1f03cbfa PT	311	#define CONFIG_PANIC_HANG /* do not reset board on panic */
1f03cbfa PT	312	#define CONFIG_PREBOOT /* enable preboot variable */
1f03cbfa PT	313	#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
	314	#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
	315
	316	/*
	317	* For booting Linux, the board info and command line data
	318	* have to be in the first 16 MB of memory, since this is
	319	* the maximum mapped by the Linux kernel during initialization.
	320	*/
	321	#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
39121c08	322	#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
1f03cbfa	323
1f03cbfa PT	324	/*
	325	* Environment Configuration
	326	*/
	327	#define CONFIG_ENV_IS_IN_FLASH 1
	328	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
	329	#define CONFIG_ENV_SIZE 0x8000
	330	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
	331
	332	/*
	333	* Flash memory map:
	334	* fff80000 - ffffffff Pri U-Boot (512 KB)
	335	* fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
	336	* fff00000 - fff3ffff Pri FDT (256KB)
	337	* fef00000 - ffefffff Pri OS image (16MB)
	338	* fc000000 - feefffff Pri OS Use/Filesystem (47MB)
	339	*
	340	* fbf80000 - fbffffff Sec U-Boot (512 KB)
	341	* fbf40000 - fbf7ffff Sec U-Boot Environment (256 KB)
	342	* fbf00000 - fbf3ffff Sec FDT (256KB)
	343	* faf00000 - fbefffff Sec OS image (16MB)
	344	* f8000000 - faefffff Sec OS Use/Filesystem (47MB)
	345	*/
5368c55d MV	346	#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
	347	#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xfbf80000)
	348	#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
	349	#define CONFIG_FDT2_ENV_ADDR __stringify(0xfbf00000)
	350	#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
	351	#define CONFIG_OS2_ENV_ADDR __stringify(0xfaf00000)
1f03cbfa PT	352
	353	#define CONFIG_PROG_UBOOT1 \
	354	"$download_cmd $loadaddr $ubootfile; " \
	355	"if test $? -eq 0; then " \
	356	"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
	357	"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
	358	"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
	359	"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
	360	"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
	361	"if test $? -ne 0; then " \
	362	"echo PROGRAM FAILED; " \
	363	"else; " \
	364	"echo PROGRAM SUCCEEDED; " \
	365	"fi; " \
	366	"else; " \
	367	"echo DOWNLOAD FAILED; " \
	368	"fi;"
	369
	370	#define CONFIG_PROG_UBOOT2 \
	371	"$download_cmd $loadaddr $ubootfile; " \
	372	"if test $? -eq 0; then " \
	373	"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
	374	"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
	375	"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
	376	"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
	377	"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
	378	"if test $? -ne 0; then " \
	379	"echo PROGRAM FAILED; " \
	380	"else; " \
	381	"echo PROGRAM SUCCEEDED; " \
	382	"fi; " \
	383	"else; " \
	384	"echo DOWNLOAD FAILED; " \
	385	"fi;"
	386
	387	#define CONFIG_BOOT_OS_NET \
	388	"$download_cmd $osaddr $osfile; " \
	389	"if test $? -eq 0; then " \
	390	"if test -n $fdtaddr; then " \
	391	"$download_cmd $fdtaddr $fdtfile; " \
	392	"if test $? -eq 0; then " \
	393	"bootm $osaddr - $fdtaddr; " \
	394	"else; " \
	395	"echo FDT DOWNLOAD FAILED; " \
	396	"fi; " \
	397	"else; " \
	398	"bootm $osaddr; " \
	399	"fi; " \
	400	"else; " \
	401	"echo OS DOWNLOAD FAILED; " \
	402	"fi;"
	403
	404	#define CONFIG_PROG_OS1 \
	405	"$download_cmd $osaddr $osfile; " \
	406	"if test $? -eq 0; then " \
	407	"erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
	408	"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
	409	"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
	410	"if test $? -ne 0; then " \
	411	"echo OS PROGRAM FAILED; " \
	412	"else; " \
	413	"echo OS PROGRAM SUCCEEDED; " \
	414	"fi; " \
	415	"else; " \
416	"echo OS DOWNLOAD FAILED; " \
417	"fi;"
418
419	#define CONFIG_PROG_OS2 \
420	"$download_cmd $osaddr $osfile; " \
421	"if test $? -eq 0; then " \
422	"erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
423	"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
424	"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
425	"if test $? -ne 0; then " \
426	"echo OS PROGRAM FAILED; " \
427	"else; " \
428	"echo OS PROGRAM SUCCEEDED; " \
429	"fi; " \
430	"else; " \
431	"echo OS DOWNLOAD FAILED; " \
432	"fi;"
433
434	#define CONFIG_PROG_FDT1 \
435	"$download_cmd $fdtaddr $fdtfile; " \
436	"if test $? -eq 0; then " \
437	"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
438	"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
439	"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
440	"if test $? -ne 0; then " \
441	"echo FDT PROGRAM FAILED; " \
442	"else; " \
443	"echo FDT PROGRAM SUCCEEDED; " \
444	"fi; " \
445	"else; " \
446	"echo FDT DOWNLOAD FAILED; " \
447	"fi;"
448
449	#define CONFIG_PROG_FDT2 \
450	"$download_cmd $fdtaddr $fdtfile; " \
451	"if test $? -eq 0; then " \
452	"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
453	"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
454	"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
455	"if test $? -ne 0; then " \
456	"echo FDT PROGRAM FAILED; " \
457	"else; " \
458	"echo FDT PROGRAM SUCCEEDED; " \
459	"fi; " \
460	"else; " \
461	"echo FDT DOWNLOAD FAILED; " \
462	"fi;"
463
464	#define CONFIG_EXTRA_ENV_SETTINGS \
465	"autoload=yes\0" \
466	"download_cmd=tftp\0" \
467	"console_args=console=ttyS0,115200\0" \
468	"root_args=root=/dev/nfs rw\0" \
469	"misc_args=ip=on\0" \
470	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
471	"bootfile=/home/user/file\0" \
c00ac259 PT	472	"osfile=/home/user/board.uImage\0" \
c00ac259 PT	473	"fdtfile=/home/user/board.dtb\0" \
1f03cbfa	474	"ubootfile=/home/user/u-boot.bin\0" \
b24a4f62	475	"fdtaddr=0x1e00000\0" \
1f03cbfa PT	476	"osaddr=0x1000000\0" \
	477	"loadaddr=0x1000000\0" \
	478	"prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
	479	"prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
	480	"prog_os1="CONFIG_PROG_OS1"\0" \
	481	"prog_os2="CONFIG_PROG_OS2"\0" \
	482	"prog_fdt1="CONFIG_PROG_FDT1"\0" \
	483	"prog_fdt2="CONFIG_PROG_FDT2"\0" \
	484	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
	485	"bootcmd_flash1=run set_bootargs; " \
	486	"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
	487	"bootcmd_flash2=run set_bootargs; " \
	488	"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
	489	"bootcmd=run bootcmd_flash1\0"
	490	#endif /* __CONFIG_H */