[people/ms/u-boot.git] / include / configs / xpedite550x.h

/*
 * Copyright 2010 Extreme Engineering Solutions, Inc.
 * Copyright 2007-2008 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * xpedite550x board configuration file
 */
#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_BOOKE		1	/* BOOKE */
#define CONFIG_E500		1	/* BOOKE e500 family */
#define CONFIG_P2020		1
#define CONFIG_XPEDITE550X	1
#define CONFIG_SYS_BOARD_NAME	"XPedite5500"
#define CONFIG_SYS_FORM_PMC_XMC	1
#define CONFIG_PRPMC_PCI_ALIAS	"pci0"	/* Processor PMC interface on pci0 */
#define CONFIG_BOARD_EARLY_INIT_R	/* Call board_pre_init */
#define CONFIG_DISPLAY_BOARDINFO

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE	0xfff80000
#endif

#define CONFIG_PCI		1	/* Enable PCI/PCIE */
#define CONFIG_PCI_PNP		1	/* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup */
#define CONFIG_PCIE1		1	/* PCIE controler 1 (PEX8112 or XMC) */
#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
#define CONFIG_FSL_ELBC		1

/*
 * Multicore config
 */
#define CONFIG_MP
#define CONFIG_BPTR_VIRT_ADDR	0xee000000	/* virt boot page address */
#define CONFIG_MPC8xxx_DISABLE_BPTR		/* Don't leave BPTR enabled */

/*
 * DDR config
 */
#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
#define SPD_EEPROM_ADDRESS			0x54
#define SPD_EEPROM_OFFSET		0x200	/* OFFSET of SPD in EEPROM */
#define CONFIG_NUM_DDR_CONTROLLERS	1
#define CONFIG_DIMM_SLOTS_PER_CTLR	1
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
#define CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM

#ifndef __ASSEMBLY__
extern unsigned long get_board_sys_clk(unsigned long dummy);
extern unsigned long get_board_ddr_clk(unsigned long dummy);
#endif

#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk(0) /* ddrclk for MPC85xx */

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE			/* toggle L2 cache */
#define CONFIG_BTB			/* toggle branch predition */
#define CONFIG_ENABLE_36BIT_PHYS	1

#define CONFIG_SYS_CCSRBAR		0xef000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR

/*
 * Diagnostics
 */
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_SYS_MEMTEST_START	0x10000000
#define CONFIG_SYS_MEMTEST_END		0x20000000
#define CONFIG_POST			(CONFIG_SYS_POST_MEMORY | \
					 CONFIG_SYS_POST_I2C)
#define I2C_ADDR_LIST			{CONFIG_SYS_I2C_EEPROM_ADDR,	\
					 CONFIG_SYS_I2C_LM75_ADDR,	\
					 CONFIG_SYS_I2C_LM90_ADDR,	\
					 CONFIG_SYS_I2C_PCA953X_ADDR0,	\
					 CONFIG_SYS_I2C_PCA953X_ADDR2,	\
					 CONFIG_SYS_I2C_PCA953X_ADDR3,	\
					 CONFIG_SYS_I2C_RTC_ADDR}

/*
 * Memory map
 * 0x0000_0000 0x7fff_ffff	DDR			2G Cacheable
 * 0x8000_0000 0xbfff_ffff	PCIe1 Mem		1G non-cacheable
 * 0xe000_0000 0xe7ff_ffff	SRAM/SSRAM/L1 Cache	128M non-cacheable
 * 0xe800_0000 0xe87f_ffff	PCIe1 IO		8M non-cacheable
 * 0xee00_0000 0xee00_ffff	Boot page translation	4K non-cacheable
 * 0xef00_0000 0xef0f_ffff	CCSR/IMMR		1M non-cacheable
 * 0xef80_0000 0xef8f_ffff	NAND Flash		1M non-cacheable
 * 0xf000_0000 0xf7ff_ffff	NOR Flash 2		128M non-cacheable
 * 0xf800_0000 0xffff_ffff	NOR Flash 1		128M non-cacheable
 */

#define CONFIG_SYS_LBC_LCRR	(LCRR_CLKDIV_8 | LCRR_EADC_3)

/*
 * NAND flash configuration
 */
#define CONFIG_SYS_NAND_BASE		0xef800000
#define CONFIG_SYS_NAND_BASE2		0xef840000 /* Unused at this time */
#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE, \
					 CONFIG_SYS_NAND_BASE2}
#define CONFIG_SYS_MAX_NAND_DEVICE	2
#define CONFIG_NAND_FSL_ELBC

/*
 * NOR flash configuration
 */
#define CONFIG_SYS_FLASH_BASE		0xf8000000
#define CONFIG_SYS_FLASH_BASE2		0xf0000000
#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST	{ {0xfff40000, 0xc0000}, \
						  {0xf7f40000, 0xc0000} }
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

/*
 * Chip select configuration
 */
/* NOR Flash 0 on CS0 */
#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE	| \
				 BR_PS_16		| \
				 BR_V)
#define CONFIG_SYS_OR0_PRELIM	(OR_AM_128MB		| \
				 OR_GPCM_CSNT		| \
				 OR_GPCM_XACS		| \
				 OR_GPCM_ACS_DIV2	| \
				 OR_GPCM_SCY_8		| \
				 OR_GPCM_TRLX		| \
				 OR_GPCM_EHTR		| \
				 OR_GPCM_EAD)

/* NOR Flash 1 on CS1 */
#define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_FLASH_BASE2	| \
				 BR_PS_16		| \
				 BR_V)
#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM

/* NAND flash on CS2 */
#define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_NAND_BASE	| \
				 (2<<BR_DECC_SHIFT)	| \
				 BR_PS_8		| \
				 BR_MS_FCM		| \
				 BR_V)

/* NAND flash on CS2 */
#define CONFIG_SYS_OR2_PRELIM	(OR_AM_256KB	| \
				 OR_FCM_PGS	| \
				 OR_FCM_CSCT	| \
				 OR_FCM_CST	| \
				 OR_FCM_CHT	| \
				 OR_FCM_SCY_1	| \
				 OR_FCM_TRLX	| \
				 OR_FCM_EHTR)

/* NAND flash on CS3 */
#define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_NAND_BASE2	| \
				 (2<<BR_DECC_SHIFT)	| \
				 BR_PS_8		| \
				 BR_MS_FCM		| \
				 BR_V)
#define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM

/*
 * Use L1 as initial stack
 */
#define CONFIG_SYS_INIT_RAM_LOCK	1
#define CONFIG_SYS_INIT_RAM_ADDR	0xe0000000
#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX		1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE	1
#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
#define CONFIG_SYS_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_BAUDRATE			115200
#define CONFIG_LOADS_ECHO		1	/* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

/*
 * Use the HUSH parser
 */
#define CONFIG_SYS_HUSH_PARSER

/*
 * Pass open firmware flat tree
 */
#define CONFIG_OF_LIBFDT		1
#define CONFIG_OF_BOARD_SETUP		1
#define CONFIG_OF_STDOUT_VIA_ALIAS	1
#define CONFIG_FDT_FIXUP_PCI_IRQ	1

/*
 * I2C
 */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	400000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED	400000
#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100

/* I2C DS7505 temperature sensor */
#define CONFIG_DTT_LM75
#define CONFIG_DTT_SENSORS		{ 0 }
#define CONFIG_SYS_I2C_LM75_ADDR	0x48

/* I2C ADT7461 temperature sensor */
#define CONFIG_SYS_I2C_LM90_ADDR	0x4C

/* I2C EEPROM - AT24C128B */
#define CONFIG_SYS_I2C_EEPROM_ADDR		0x54
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6	/* 64 byte pages */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* take up to 10 msec */

/* I2C RTC */
#define CONFIG_RTC_M41T11		1
#define CONFIG_SYS_I2C_RTC_ADDR		0x68
#define CONFIG_SYS_M41T11_BASE_YEAR	2000

/* GPIO */
#define CONFIG_PCA953X
#define CONFIG_SYS_I2C_PCA953X_ADDR0	0x18
#define CONFIG_SYS_I2C_PCA953X_ADDR1	0x1c
#define CONFIG_SYS_I2C_PCA953X_ADDR2	0x1e
#define CONFIG_SYS_I2C_PCA953X_ADDR3	0x1f
#define CONFIG_SYS_I2C_PCA953X_ADDR	CONFIG_SYS_I2C_PCA953X_ADDR0

/*
 * GPIO pin definitions, PU = pulled high, PD = pulled low
 */
/* PCA9557 @ 0x18*/
#define CONFIG_SYS_PCA953X_C0_SER0_EN		0x01 /* PU; UART0 enable (1: enabled) */
#define CONFIG_SYS_PCA953X_C0_SER0_MODE		0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
#define CONFIG_SYS_PCA953X_C0_SER1_EN		0x04 /* PU; UART1 enable (1: enabled) */
#define CONFIG_SYS_PCA953X_C0_SER1_MODE		0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS	0x10 /* PU; Boot flash CS select */
#define CONFIG_SYS_PCA953X_NVM_WP		0x20 /* PU; Write protection (0: disabled, 1: enabled) */

/* PCA9557 @ 0x1e*/
#define CONFIG_SYS_PCA953X_XMC_GA0		0x01 /* PU; */
#define CONFIG_SYS_PCA953X_XMC_GA1		0x02 /* PU; */
#define CONFIG_SYS_PCA953X_XMC_GA2		0x04 /* PU; */
#define CONFIG_SYS_PCA953X_XMC_WAKE		0x10 /* PU; */
#define CONFIG_SYS_PCA953X_XMC_BIST		0x20 /* Enable XMC BIST */
#define CONFIG_SYS_PCA953X_PMC_EREADY		0x40 /* PU; PMC PCI eready */
#define CONFIG_SYS_PCA953X_PMC_MONARCH		0x80 /* PMC monarch mode enable */

/* PCA9557 @ 0x1f */
#define CONFIG_SYS_PCA953X_MC_GPIO0		0x01 /* PU; */
#define CONFIG_SYS_PCA953X_MC_GPIO1		0x02 /* PU; */
#define CONFIG_SYS_PCA953X_MC_GPIO2		0x04 /* PU; */
#define CONFIG_SYS_PCA953X_MC_GPIO3		0x08 /* PU; */
#define CONFIG_SYS_PCA953X_MC_GPIO4		0x10 /* PU; */
#define CONFIG_SYS_PCA953X_MC_GPIO5		0x20 /* PU; */
#define CONFIG_SYS_PCA953X_MC_GPIO6		0x40 /* PU; */
#define CONFIG_SYS_PCA953X_MC_GPIO7		0x80 /* PU; */

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

/* controller 1 - PEX8112 or XMC, depending on build option */
#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
#define CONFIG_SYS_PCIE1_MEM_SIZE	0x40000000	/* 1G */
#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS	0xe8000000
#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */


/*
 * Networking options
 */
#define CONFIG_TSEC_ENET		/* tsec ethernet support */
#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
#define CONFIG_TSEC_TBI
#define CONFIG_MII		1	/* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
#define CONFIG_ETHPRIME		"eTSEC2"

/*
 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
 * 1000mbps SGMII link
 */
#define CONFIG_TSEC_TBICR_SETTINGS ( \
		TBICR_PHY_RESET \
		| TBICR_FULL_DUPLEX \
		| TBICR_SPEED1_SET \
		)

#define CONFIG_TSEC1		1
#define CONFIG_TSEC1_NAME	"eTSEC1"
#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHY_ADDR		1
#define TSEC1_PHYIDX		0
#define CONFIG_HAS_ETH0

#define CONFIG_TSEC2		1
#define CONFIG_TSEC2_NAME	"eTSEC2"
#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_PHY_ADDR		2
#define TSEC2_PHYIDX		0
#define CONFIG_HAS_ETH1

#define CONFIG_TSEC3		1
#define CONFIG_TSEC3_NAME	"eTSEC3"
#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_PHY_ADDR		3
#define TSEC3_PHYIDX		0
#define CONFIG_HAS_ETH2

/*
 * USB
 */
#define CONFIG_USB_STORAGE
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_DOS_PARTITION

/*
 * Command configuration.
 */
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCA953X
#define CONFIG_CMD_PCA953X_INFO
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PCI_ENUM
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_USB

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
#define CONFIG_CMDLINE_EDITING	1		/* add command line history	*/
#define CONFIG_AUTO_COMPLETE	1		/* add autocompletion support */
#define CONFIG_LOADADDR		0x1000000	/* default location for tftp and bootm */
#define CONFIG_BOOTDELAY	3		/* -1 disables auto-boot */
#define CONFIG_PANIC_HANG			/* do not reset board on panic */
#define CONFIG_PREBOOT				/* enable preboot variable */
#define CONFIG_FIT		1
#define CONFIG_FIT_VERBOSE	1
#define CONFIG_INTEGRITY			/* support booting INTEGRITY OS */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 16 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN	(16 << 20)	/* Increase max gunzip size */

/*
 * Environment Configuration
 */
#define CONFIG_ENV_IS_IN_FLASH	1
#define CONFIG_ENV_SECT_SIZE	0x20000		/* 128k (one sector) for env */
#define CONFIG_ENV_SIZE		0x8000
#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - (256 * 1024))

/*
 * Flash memory map:
 * fff80000 - ffffffff     Pri U-Boot (512 KB)
 * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
 * fff00000 - fff3ffff     Pri FDT (256KB)
 * fef00000 - ffefffff     Pri OS image (16MB)
 * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
 *
 * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
 * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
 * f7f00000 - f7f3ffff     Sec FDT (256KB)
 * f6f00000 - f7efffff     Sec OS image (16MB)
 * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
 */
#define CONFIG_UBOOT1_ENV_ADDR	__stringify(0xfff80000)
#define CONFIG_UBOOT2_ENV_ADDR	__stringify(0xf7f80000)
#define CONFIG_FDT1_ENV_ADDR	__stringify(0xfff00000)
#define CONFIG_FDT2_ENV_ADDR	__stringify(0xf7f00000)
#define CONFIG_OS1_ENV_ADDR	__stringify(0xfef00000)
#define CONFIG_OS2_ENV_ADDR	__stringify(0xf6f00000)

#define CONFIG_PROG_UBOOT1						\
	"$download_cmd $loadaddr $ubootfile; "				\
	"if test $? -eq 0; then "					\
		"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
		"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
		"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "	\
		"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "		\
		"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "	\
		"if test $? -ne 0; then "				\
			"echo PROGRAM FAILED; "				\
		"else; "						\
			"echo PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_UBOOT2						\
	"$download_cmd $loadaddr $ubootfile; "				\
	"if test $? -eq 0; then "					\
		"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
		"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
		"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "	\
		"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "		\
		"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "	\
		"if test $? -ne 0; then "				\
			"echo PROGRAM FAILED; "				\
		"else; "						\
			"echo PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_BOOT_OS_NET						\
	"$download_cmd $osaddr $osfile; "				\
	"if test $? -eq 0; then "					\
		"if test -n $fdtaddr; then "				\
			"$download_cmd $fdtaddr $fdtfile; "		\
			"if test $? -eq 0; then "			\
				"bootm $osaddr - $fdtaddr; "		\
			"else; "					\
				"echo FDT DOWNLOAD FAILED; "		\
			"fi; "						\
		"else; "						\
			"bootm $osaddr; "				\
		"fi; "							\
	"else; "							\
		"echo OS DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_OS1							\
	"$download_cmd $osaddr $osfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_OS1_ENV_ADDR" +$filesize; "		\
		"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
		"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo OS PROGRAM FAILED; "			\
		"else; "						\
			"echo OS PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo OS DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_OS2							\
	"$download_cmd $osaddr $osfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_OS2_ENV_ADDR" +$filesize; "		\
		"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
		"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo OS PROGRAM FAILED; "			\
		"else; "						\
			"echo OS PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo OS DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_FDT1						\
	"$download_cmd $fdtaddr $fdtfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"		\
		"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
		"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo FDT PROGRAM FAILED; "			\
		"else; "						\
			"echo FDT PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo FDT DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_PROG_FDT2						\
	"$download_cmd $fdtaddr $fdtfile; "				\
	"if test $? -eq 0; then "					\
		"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"		\
		"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
		"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "	\
		"if test $? -ne 0; then "				\
			"echo FDT PROGRAM FAILED; "			\
		"else; "						\
			"echo FDT PROGRAM SUCCEEDED; "			\
		"fi; "							\
	"else; "							\
		"echo FDT DOWNLOAD FAILED; "				\
	"fi;"

#define CONFIG_EXTRA_ENV_SETTINGS					\
	"autoload=yes\0"						\
	"download_cmd=tftp\0"						\
	"console_args=console=ttyS0,115200\0"				\
	"root_args=root=/dev/nfs rw\0"					\
	"misc_args=ip=on\0"						\
	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
	"bootfile=/home/user/file\0"					\
	"osfile=/home/user/board.uImage\0"				\
	"fdtfile=/home/user/board.dtb\0"				\
	"ubootfile=/home/user/u-boot.bin\0"				\
	"fdtaddr=c00000\0"						\
	"osaddr=0x1000000\0"						\
	"loadaddr=0x1000000\0"						\
	"prog_uboot1="CONFIG_PROG_UBOOT1"\0"				\
	"prog_uboot2="CONFIG_PROG_UBOOT2"\0"				\
	"prog_os1="CONFIG_PROG_OS1"\0"					\
	"prog_os2="CONFIG_PROG_OS2"\0"					\
	"prog_fdt1="CONFIG_PROG_FDT1"\0"				\
	"prog_fdt2="CONFIG_PROG_FDT2"\0"				\
	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"		\
	"bootcmd_flash1=run set_bootargs; "				\
		"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
	"bootcmd_flash2=run set_bootargs; "				\
		"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
	"bootcmd=run bootcmd_flash1\0"
#endif	/* __CONFIG_H */
Commit	Line	Data
bfe18815 JS	1	/*
	2	* Copyright 2010 Extreme Engineering Solutions, Inc.
	3	* Copyright 2007-2008 Freescale Semiconductor, Inc.
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
bfe18815 JS	6	*/
	7
	8	/*
	9	* xpedite550x board configuration file
	10	*/
	11	#ifndef __CONFIG_H
	12	#define __CONFIG_H
	13
	14	/*
	15	* High Level Configuration Options
	16	*/
	17	#define CONFIG_BOOKE 1 /* BOOKE */
	18	#define CONFIG_E500 1 /* BOOKE e500 family */
bfe18815 JS	19	#define CONFIG_P2020 1
	20	#define CONFIG_XPEDITE550X 1
	21	#define CONFIG_SYS_BOARD_NAME "XPedite5500"
	22	#define CONFIG_SYS_FORM_PMC_XMC 1
	23	#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */
	24	#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
02851009	25	#define CONFIG_DISPLAY_BOARDINFO
bfe18815 JS	26
	27	#ifndef CONFIG_SYS_TEXT_BASE
	28	#define CONFIG_SYS_TEXT_BASE 0xfff80000
	29	#endif
	30
	31	#define CONFIG_PCI 1 /* Enable PCI/PCIE */
	32	#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
	33	#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
	34	#define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */
	35	#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
842033e6	36	#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
bfe18815 JS	37	#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
	38	#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
	39	#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
	40	#define CONFIG_FSL_ELBC 1
	41
	42	/*
	43	* Multicore config
	44	*/
	45	#define CONFIG_MP
	46	#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
	47	#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
	48
	49	/*
	50	* DDR config
	51	*/
5614e71b	52	#define CONFIG_SYS_FSL_DDR3
bfe18815 JS	53	#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
	54	#define CONFIG_DDR_SPD
	55	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
c39f44dc	56	#define SPD_EEPROM_ADDRESS 0x54
bfe18815 JS	57	#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
	58	#define CONFIG_NUM_DDR_CONTROLLERS 1
	59	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	60	#define CONFIG_CHIP_SELECTS_PER_CTRL 2
	61	#define CONFIG_DDR_ECC
	62	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	63	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
	64	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	65	#define CONFIG_VERY_BIG_RAM
	66
	67	#ifndef __ASSEMBLY__
	68	extern unsigned long get_board_sys_clk(unsigned long dummy);
	69	extern unsigned long get_board_ddr_clk(unsigned long dummy);
	70	#endif
	71
	72	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
	73	#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
	74
	75	/*
	76	* These can be toggled for performance analysis, otherwise use default.
	77	*/
	78	#define CONFIG_L2_CACHE /* toggle L2 cache */
	79	#define CONFIG_BTB /* toggle branch predition */
	80	#define CONFIG_ENABLE_36BIT_PHYS 1
	81
e46fedfe TT	82	#define CONFIG_SYS_CCSRBAR 0xef000000
e46fedfe TT	83	#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
bfe18815 JS	84
	85	/*
	86	* Diagnostics
	87	*/
	88	#define CONFIG_SYS_ALT_MEMTEST
	89	#define CONFIG_SYS_MEMTEST_START 0x10000000
	90	#define CONFIG_SYS_MEMTEST_END 0x20000000
	91	#define CONFIG_POST (CONFIG_SYS_POST_MEMORY \| \
	92	CONFIG_SYS_POST_I2C)
	93	#define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \
	94	CONFIG_SYS_I2C_LM75_ADDR, \
	95	CONFIG_SYS_I2C_LM90_ADDR, \
	96	CONFIG_SYS_I2C_PCA953X_ADDR0, \
	97	CONFIG_SYS_I2C_PCA953X_ADDR2, \
	98	CONFIG_SYS_I2C_PCA953X_ADDR3, \
	99	CONFIG_SYS_I2C_RTC_ADDR}
	100
	101	/*
	102	* Memory map
	103	* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
	104	* 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
	105	* 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
	106	* 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
	107	* 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable
	108	* 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
	109	* 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
	110	* 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
	111	* 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
	112	*/
	113
	114	#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 \| LCRR_EADC_3)
	115
	116	/*
	117	* NAND flash configuration
	118	*/
	119	#define CONFIG_SYS_NAND_BASE 0xef800000
	120	#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
	121	#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
	122	CONFIG_SYS_NAND_BASE2}
	123	#define CONFIG_SYS_MAX_NAND_DEVICE 2
bfe18815 JS	124	#define CONFIG_NAND_FSL_ELBC
	125
	126	/*
	127	* NOR flash configuration
	128	*/
	129	#define CONFIG_SYS_FLASH_BASE 0xf8000000
	130	#define CONFIG_SYS_FLASH_BASE2 0xf0000000
	131	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
	132	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
	133	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	134	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	135	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	136	#define CONFIG_FLASH_CFI_DRIVER
	137	#define CONFIG_SYS_FLASH_CFI
	138	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	139	#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
	140	{0xf7f40000, 0xc0000} }
	141	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	142
	143	/*
	144	* Chip select configuration
	145	*/
	146	/* NOR Flash 0 on CS0 */
	147	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| \
	148	BR_PS_16 \| \
	149	BR_V)
	150	#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB \| \
	151	OR_GPCM_CSNT \| \
	152	OR_GPCM_XACS \| \
	153	OR_GPCM_ACS_DIV2 \| \
	154	OR_GPCM_SCY_8 \| \
	155	OR_GPCM_TRLX \| \
	156	OR_GPCM_EHTR \| \
	157	OR_GPCM_EAD)
	158
	159	/* NOR Flash 1 on CS1 */
	160	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 \| \
	161	BR_PS_16 \| \
	162	BR_V)
	163	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
	164
	165	/* NAND flash on CS2 */
	166	#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE \| \
	167	(2<<BR_DECC_SHIFT) \| \
	168	BR_PS_8 \| \
	169	BR_MS_FCM \| \
	170	BR_V)
	171
	172	/* NAND flash on CS2 */
	173	#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB \| \
	174	OR_FCM_PGS \| \
	175	OR_FCM_CSCT \| \
	176	OR_FCM_CST \| \
	177	OR_FCM_CHT \| \
	178	OR_FCM_SCY_1 \| \
	179	OR_FCM_TRLX \| \
	180	OR_FCM_EHTR)
	181
	182	/* NAND flash on CS3 */
	183	#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 \| \
	184	(2<<BR_DECC_SHIFT) \| \
	185	BR_PS_8 \| \
	186	BR_MS_FCM \| \
	187	BR_V)
188	#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
189
190	/*
191	* Use L1 as initial stack
192	*/
193	#define CONFIG_SYS_INIT_RAM_LOCK 1
194	#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
553f0982	195	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
bfe18815	196
25ddd1fb	197	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
bfe18815 JS	198	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	199
	200	#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
	201	#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
	202
	203	/*
	204	* Serial Port
	205	*/
	206	#define CONFIG_CONS_INDEX 1
bfe18815 JS	207	#define CONFIG_SYS_NS16550_SERIAL
	208	#define CONFIG_SYS_NS16550_REG_SIZE 1
	209	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	210	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
	211	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
	212	#define CONFIG_SYS_BAUDRATE_TABLE \
	213	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
	214	#define CONFIG_BAUDRATE 115200
	215	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	216	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
	217
	218	/*
	219	* Use the HUSH parser
	220	*/
	221	#define CONFIG_SYS_HUSH_PARSER
bfe18815 JS	222
	223	/*
	224	* Pass open firmware flat tree
	225	*/
	226	#define CONFIG_OF_LIBFDT 1
	227	#define CONFIG_OF_BOARD_SETUP 1
	228	#define CONFIG_OF_STDOUT_VIA_ALIAS 1
	229	#define CONFIG_FDT_FIXUP_PCI_IRQ 1
	230
	231	/*
	232	* I2C
	233	*/
00f792e0 HS	234	#define CONFIG_SYS_I2C
	235	#define CONFIG_SYS_I2C_FSL
	236	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	237	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	238	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	239	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	240	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	241	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
bfe18815 JS	242
	243	/* I2C DS7505 temperature sensor */
	244	#define CONFIG_DTT_LM75
	245	#define CONFIG_DTT_SENSORS { 0 }
	246	#define CONFIG_SYS_I2C_LM75_ADDR 0x48
	247
	248	/* I2C ADT7461 temperature sensor */
	249	#define CONFIG_SYS_I2C_LM90_ADDR 0x4C
	250
	251	/* I2C EEPROM - AT24C128B */
	252	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
	253	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	254	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
	255	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
	256
	257	/* I2C RTC */
	258	#define CONFIG_RTC_M41T11 1
	259	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
	260	#define CONFIG_SYS_M41T11_BASE_YEAR 2000
	261
	262	/* GPIO */
	263	#define CONFIG_PCA953X
	264	#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
	265	#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
	266	#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
	267	#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
	268	#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
	269
	270	/*
	271	* GPIO pin definitions, PU = pulled high, PD = pulled low
	272	*/
	273	/* PCA9557 @ 0x18*/
	274	#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
	275	#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
	276	#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
	277	#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
	278	#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
	279	#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */
	280
	281	/* PCA9557 @ 0x1e*/
	282	#define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */
	283	#define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */
	284	#define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */
	285	#define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */
	286	#define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */
	287	#define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */
	288	#define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */
	289
	290	/* PCA9557 @ 0x1f */
	291	#define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */
	292	#define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */
	293	#define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */
	294	#define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */
	295	#define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */
	296	#define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */
	297	#define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */
	298	#define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */
	299
	300	/*
	301	* General PCI
	302	* Memory space is mapped 1-1, but I/O space must start from 0.
	303	*/
	304
	305	/* controller 1 - PEX8112 or XMC, depending on build option */
306	#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
307	#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
308	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
309	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
310	#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
311	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
312
313
314	/*
315	* Networking options
316	*/
317	#define CONFIG_TSEC_ENET /* tsec ethernet support */
318	#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
bfe18815 JS	319	#define CONFIG_TSEC_TBI
	320	#define CONFIG_MII 1 /* MII PHY management */
	321	#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
	322	#define CONFIG_ETHPRIME "eTSEC2"
	323
72c96a68 KG	324	/*
	325	* In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
	326	* 1000mbps SGMII link
	327	*/
	328	#define CONFIG_TSEC_TBICR_SETTINGS ( \
	329	TBICR_PHY_RESET \
	330	\| TBICR_FULL_DUPLEX \
	331	\| TBICR_SPEED1_SET \
	332	)
	333
bfe18815 JS	334	#define CONFIG_TSEC1 1
	335	#define CONFIG_TSEC1_NAME "eTSEC1"
	336	#define TSEC1_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	337	#define TSEC1_PHY_ADDR 1
	338	#define TSEC1_PHYIDX 0
	339	#define CONFIG_HAS_ETH0
	340
	341	#define CONFIG_TSEC2 1
	342	#define CONFIG_TSEC2_NAME "eTSEC2"
	343	#define TSEC2_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	344	#define TSEC2_PHY_ADDR 2
	345	#define TSEC2_PHYIDX 0
	346	#define CONFIG_HAS_ETH1
	347
	348	#define CONFIG_TSEC3 1
	349	#define CONFIG_TSEC3_NAME "eTSEC3"
	350	#define TSEC3_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	351	#define TSEC3_PHY_ADDR 3
	352	#define TSEC3_PHYIDX 0
	353	#define CONFIG_HAS_ETH2
	354
	355	/*
	356	* USB
	357	*/
	358	#define CONFIG_USB_STORAGE
	359	#define CONFIG_USB_EHCI
	360	#define CONFIG_USB_EHCI_FSL
	361	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	362	#define CONFIG_DOS_PARTITION
	363
	364	/*
	365	* Command configuration.
	366	*/
bfe18815 JS	367	#define CONFIG_CMD_ASKENV
	368	#define CONFIG_CMD_DATE
	369	#define CONFIG_CMD_DHCP
	370	#define CONFIG_CMD_DTT
	371	#define CONFIG_CMD_EEPROM
bfe18815 JS	372	#define CONFIG_CMD_I2C
	373	#define CONFIG_CMD_JFFS2
	374	#define CONFIG_CMD_MII
	375	#define CONFIG_CMD_NAND
bfe18815 JS	376	#define CONFIG_CMD_PCA953X
	377	#define CONFIG_CMD_PCA953X_INFO
	378	#define CONFIG_CMD_PCI
	379	#define CONFIG_CMD_PCI_ENUM
	380	#define CONFIG_CMD_PING
	381	#define CONFIG_CMD_REGINFO
bfe18815 JS	382	#define CONFIG_CMD_SNTP
	383	#define CONFIG_CMD_USB
	384
	385	/*
	386	* Miscellaneous configurable options
	387	*/
	388	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	389	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
bfe18815 JS	390	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	391	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	392	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	393	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
bfe18815 JS	394	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	395	#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
	396	#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
	397	#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
	398	#define CONFIG_PANIC_HANG /* do not reset board on panic */
	399	#define CONFIG_PREBOOT /* enable preboot variable */
	400	#define CONFIG_FIT 1
	401	#define CONFIG_FIT_VERBOSE 1
	402	#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
	403
	404	/*
	405	* For booting Linux, the board info and command line data
	406	* have to be in the first 16 MB of memory, since this is
	407	* the maximum mapped by the Linux kernel during initialization.
	408	*/
	409	#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
	410	#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
	411
bfe18815 JS	412	/*
	413	* Environment Configuration
	414	*/
	415	#define CONFIG_ENV_IS_IN_FLASH 1
	416	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
	417	#define CONFIG_ENV_SIZE 0x8000
	418	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
	419
	420	/*
	421	* Flash memory map:
	422	* fff80000 - ffffffff Pri U-Boot (512 KB)
	423	* fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
	424	* fff00000 - fff3ffff Pri FDT (256KB)
	425	* fef00000 - ffefffff Pri OS image (16MB)
	426	* f8000000 - feefffff Pri OS Use/Filesystem (111MB)
	427	*
	428	* f7f80000 - f7ffffff Sec U-Boot (512 KB)
	429	* f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
	430	* f7f00000 - f7f3ffff Sec FDT (256KB)
	431	* f6f00000 - f7efffff Sec OS image (16MB)
	432	* f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
	433	*/
5368c55d MV	434	#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
	435	#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000)
	436	#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000)
	437	#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000)
	438	#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000)
	439	#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000)
bfe18815 JS	440
	441	#define CONFIG_PROG_UBOOT1 \
	442	"$download_cmd $loadaddr $ubootfile; " \
	443	"if test $? -eq 0; then " \
	444	"protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
	445	"erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
	446	"cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
	447	"protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
	448	"cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
	449	"if test $? -ne 0; then " \
	450	"echo PROGRAM FAILED; " \
	451	"else; " \
	452	"echo PROGRAM SUCCEEDED; " \
	453	"fi; " \
	454	"else; " \
	455	"echo DOWNLOAD FAILED; " \
	456	"fi;"
	457
	458	#define CONFIG_PROG_UBOOT2 \
	459	"$download_cmd $loadaddr $ubootfile; " \
	460	"if test $? -eq 0; then " \
	461	"protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
	462	"erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
	463	"cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
	464	"protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
	465	"cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
	466	"if test $? -ne 0; then " \
	467	"echo PROGRAM FAILED; " \
	468	"else; " \
	469	"echo PROGRAM SUCCEEDED; " \
	470	"fi; " \
	471	"else; " \
	472	"echo DOWNLOAD FAILED; " \
	473	"fi;"
	474
	475	#define CONFIG_BOOT_OS_NET \
	476	"$download_cmd $osaddr $osfile; " \
	477	"if test $? -eq 0; then " \
	478	"if test -n $fdtaddr; then " \
	479	"$download_cmd $fdtaddr $fdtfile; " \
	480	"if test $? -eq 0; then " \
	481	"bootm $osaddr - $fdtaddr; " \
	482	"else; " \
	483	"echo FDT DOWNLOAD FAILED; " \
	484	"fi; " \
	485	"else; " \
	486	"bootm $osaddr; " \
	487	"fi; " \
	488	"else; " \
	489	"echo OS DOWNLOAD FAILED; " \
	490	"fi;"
	491
	492	#define CONFIG_PROG_OS1 \
	493	"$download_cmd $osaddr $osfile; " \
	494	"if test $? -eq 0; then " \
	495	"erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
	496	"cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
	497	"cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
	498	"if test $? -ne 0; then " \
	499	"echo OS PROGRAM FAILED; " \
	500	"else; " \
	501	"echo OS PROGRAM SUCCEEDED; " \
	502	"fi; " \
	503	"else; " \
504	"echo OS DOWNLOAD FAILED; " \
505	"fi;"
506
507	#define CONFIG_PROG_OS2 \
508	"$download_cmd $osaddr $osfile; " \
509	"if test $? -eq 0; then " \
510	"erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
511	"cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
512	"cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
513	"if test $? -ne 0; then " \
514	"echo OS PROGRAM FAILED; " \
515	"else; " \
516	"echo OS PROGRAM SUCCEEDED; " \
517	"fi; " \
518	"else; " \
519	"echo OS DOWNLOAD FAILED; " \
520	"fi;"
521
522	#define CONFIG_PROG_FDT1 \
523	"$download_cmd $fdtaddr $fdtfile; " \
524	"if test $? -eq 0; then " \
525	"erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
526	"cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
527	"cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
528	"if test $? -ne 0; then " \
529	"echo FDT PROGRAM FAILED; " \
530	"else; " \
531	"echo FDT PROGRAM SUCCEEDED; " \
532	"fi; " \
533	"else; " \
534	"echo FDT DOWNLOAD FAILED; " \
535	"fi;"
536
537	#define CONFIG_PROG_FDT2 \
538	"$download_cmd $fdtaddr $fdtfile; " \
539	"if test $? -eq 0; then " \
540	"erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
541	"cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
542	"cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
543	"if test $? -ne 0; then " \
544	"echo FDT PROGRAM FAILED; " \
545	"else; " \
546	"echo FDT PROGRAM SUCCEEDED; " \
547	"fi; " \
548	"else; " \
549	"echo FDT DOWNLOAD FAILED; " \
550	"fi;"
551
552	#define CONFIG_EXTRA_ENV_SETTINGS \
553	"autoload=yes\0" \
554	"download_cmd=tftp\0" \
555	"console_args=console=ttyS0,115200\0" \
556	"root_args=root=/dev/nfs rw\0" \
557	"misc_args=ip=on\0" \
558	"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
559	"bootfile=/home/user/file\0" \
560	"osfile=/home/user/board.uImage\0" \
561	"fdtfile=/home/user/board.dtb\0" \
562	"ubootfile=/home/user/u-boot.bin\0" \
563	"fdtaddr=c00000\0" \
564	"osaddr=0x1000000\0" \
565	"loadaddr=0x1000000\0" \
566	"prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
567	"prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
568	"prog_os1="CONFIG_PROG_OS1"\0" \
569	"prog_os2="CONFIG_PROG_OS2"\0" \
570	"prog_fdt1="CONFIG_PROG_FDT1"\0" \
571	"prog_fdt2="CONFIG_PROG_FDT2"\0" \
572	"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
573	"bootcmd_flash1=run set_bootargs; " \
574	"bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
575	"bootcmd_flash2=run set_bootargs; " \
576	"bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
577	"bootcmd=run bootcmd_flash1\0"
578	#endif /* __CONFIG_H */